Duo to the new egalax touch driver, in Multi-touch mode, the report messages
also contain the single touch message. So there is no need to use the single
touch config.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Multi-touch Protocol is divided into two types:
Type A --> for devices handling anonymous contacts, the protocol
describes how to send the raw data for all contacts to
the receiver.
Tyep B --> for devices capable of tracking identifiable contacts,
the protocol describes how to send updates for individual
contacts via event slots.
Before this patch, our driver use type A, but wayland 1.6(GPU team)
just call type B contact to check the multi slots number. Besides,
type B can also be used in Android and Yocto, so this patch use
type B to replace type A.
The upstream EETI egalax touch driver use type B multi-touch protocol,
so this patch just use the upstream driver to replace the current
egalax touch driver.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Remove useless code for release interrupt enabled, because we check status by
timer rather than release interrupt. Remove the code which may disable depress
interrupt. Also make sure enable depress interrupt in suspend function.
Signed-off-by: Robin Gong <b38343@freescale.com>
There is a small window after system suspend but timer scan function
didn't finish timely, in this case, system enter suspend without kpp
interrupt enabled and failed to resume back if key depressed.We add
pm_stay_awake and pm_relax to make sure system suspend flow abort in
this case.
Signed-off-by: Robin Gong <b38343@freescale.com>
The isl29023 share the same interrupt gpio with mag3110 sensor. This patch add shared
interrutp support.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
evbug will open the mma8450 on i.MX6SL_EVK and mma8450 will work in 2G mode by default.
That is the reason why mma8450 logs will be printed out. The main changes is below:
* Remove the open(), close() hook out of the drivers. The open() and close()
hook in input framwork is defined as void type. It isn't strictly safe in
logic when some error happends. So remove them out.
* Modify the mma8450 to standby mode by default. It will be more power saving
and there would be no log printing out after booting up.
* Provide the sys interface to modify the mma8450 work modes. Then the higher
layer can modify the the mma8450 work mode via the interface. It would be
much safer.There would be a sclaemode interface in the folder of
/sys/devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001c/scalemode
User can use cat to read the current scalemode and echo to write. The mode
is defined as: MODE_STANDBY: 0 MODE_2G:1 MODE_4G:2 MODE_8G:3
* Add mutex to protect and some error handling.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
When system suspend, need to switch keyboard pins to sleep mode,
this is to save IO power. Using pinctrl mode switch framework
to make it happen.
Signed-off-by: Anson Huang <b20788@freescale.com>
Add chip ID check in probe function. The mma8450 is
on the E-INK daughter board. When the daughter board
is not pluged, there would be polling error log
continuously. Add the check to avoid this.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
To support wakeup system from freeze mode of suspend,
device's irq can NOT be disabled during devices suspend,
so we need to add IRQF_NO_SUSPEND flag to irqflags.
Signed-off-by: Anson Huang <b20788@freescale.com>
It's ported from 3.5.7 kernel. To test this driver, the EBook Daughter
Board need to be attached (on imx6dl sabresd or imx6sl evk board).
Signed-off-by: Robby Cai <R63905@freescale.com>
ISL29023 is an integrated ambient and infrared light to digital
converter with I2C (SMBus Compatible) Interface.
(Cherry-pick from freescale internal kernel 3.0.35_4.1.0 branch)
Signed-off-by: Luwei Zhou <b45643@freescale.com>
We need add DCM mode/AUX mode for ADC converter function of max11801, so that
it can be used to read voltage of battery. Meanwhile, let the driver based on
device tree. The patchset is based on below patch (V3.5.7):
commit 4001774cf51f0140ae7e4e8e0ec1d86475790682
Author: Rong Dian <b38775@freescale.com>
Date: Fri Jan 18 14:24:28 2013 +0800
Engr00240284-1 MAX11801: Add DCM aux adc sample function
1.Add direct conversion mode operations
2.Add aux adc sample function
Signed-off-by: Robin Gong <b38343@freescale.com>
Copy the egalax touch screen driver from linux3.5.7.Make some
modification.Remove the __devinit __devexit __devexit_p out
of the file, because 3.10 does not support.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
commit 50c5d36dab upstream.
We attempt to remove noise from coordinates reported by devices in
input_handle_abs_event(), unfortunately, unless we were dropping the
event altogether, we were ignoring the adjusted value and were passing
on the original value instead.
Reviewed-by: Andrew de los Reyes <adlr@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb4f8f568a upstream.
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9e83e275 upstream.
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d396ede22 upstream.
The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.
This is a preparation patch for simplifying the quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36189cc3cd upstream.
The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2
Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"
Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.
https://bugzilla.kernel.org/show_bug.cgi?id=61151
Reported-by: Philipp Wolfer <ph.wolfer@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d725caa9d upstream.
After issuing ATKBD_CMD_RESET_DIS, keyboard on some LG laptops stops
working. The workaround is to stop issuing ATKBD_CMD_RESET_DIS commands.
In order to keep changes in atkbd driver to the minimum we check DMI
signature and only skip ATKBD_CMD_RESET_DIS if we are running on LG
LW25-B7HV or P1-J273B.
Signed-off-by: Sheng-Liang Song <ssl@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46a2986ebb upstream.
We expect that all the Haswell series will need such quirks, sigh.
The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad,
with the same min/max issue.
The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation.
The X1 and T431s share a PnPID with the T540p, but the reported ranges are
closer to those of the T440s.
HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me,
S1 Yoga and X1 are written by Benjamin Tissoires.
Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the
X240, X1 uses the same touchpad as the T440.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6797b39e6f upstream.
The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.
The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.
When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=76341
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 421e08c41f upstream.
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c15bdfd5b9 upstream.
The current assumption in the elantech driver that hw version 3 touchpads
are never clickpads and hw version 4 touchpads are always clickpads is
wrong.
There are several bug reports for this, ie:
https://bugzilla.redhat.com/show_bug.cgi?id=1030802http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux
I've spend a couple of hours wading through various bugzillas, launchpads
and forum posts to create a list of fw-versions and capabilities for
different laptop models to find a good method to differentiate between
clickpads and versions with separate hardware buttons.
Which shows that a device being a clickpad is reliable indicated by bit 12
being set in the fw_version. I've included the gathered list inside the
driver, so that we've this info at hand if we need to revisit this later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28a2a2e1ae upstream.
We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
Rested-by: Paul Cercueil <pcercuei@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ef38351d7 upstream.
This patch supports the separate handling of the USB transfer buffer length
and the length of the buffer used for multi packet support. For devices
supporting multiple report or diagnostic packets, the USB transfer size is now
limited to the USB endpoints wMaxPacketSize - otherwise it defaults to the
configured report packet size as before.
This fixes an issue where event reporting can be delayed for an arbitrary
time for multi packet devices. For instance the report size for eGalax devices
is defined to the 16 byte maximum diagnostic packet size as opposed to the 5
byte report packet size. In case the driver requests 16 byte from the USB
interrupt endpoint, the USB host controller driver needs to split up the
request into 2 accesses according to the endpoints wMaxPacketSize of 8 byte.
When the first transfer is answered by the eGalax device with not less than
the full 8 byte requested, the host controller has got no way of knowing
whether the touch controller has got additional data queued and will issue
the second transfer. If per example a liftoff event finishes at such a
wMaxPacketSize boundary, the data will not be available to the usbtouch driver
until a further event is triggered and transfered to the host. From user
perspective the BTN_TOUCH release event in this case is stuck until the next
touch down event.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfaaed08ec upstream.
Moust (if not all) modern software, including X, uses /dev/eventX rather than
the legacy /dev/mouseX devices. It therefore makes sense for general-purpose
(distro) kernels to use MOUSEDV=m (or even n), so let's drop the EXPERT=y
requirement.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcd2623073 upstream.
There is plenty of consumer hardware (e.g., mac books) that does not use AT
keyboards or PS/2 mice. It therefore makes sense for distro kernels to
build the related drivers as modules to avoid loading them on hardware that
does not need them. As such, these options should no longer be protected by
EXPERT.
Moreover, building these drivers as modules gets rid of the following ugly
error during boot:
[ 2.337745] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 3.439537] i8042: No controller found
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78551277e4 upstream.
This allows the module to be autoloaded in the common case.
In order to work on non-PnP systems the module should be compiled in or
loaded unconditionally at boot (c.f. modules-load.d(5)), as before.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92eb77d0ff upstream.
evdev always tries to allocate the event buffer for clients using
kzalloc rather than vmalloc, presumably to avoid mapping overhead where
possible. However, drivers like bcm5974, which claims support for
reporting 16 fingers simultaneously, can have an extraordinarily large
buffer. The resultant contiguous order-4 allocation attempt fails due
to fragmentation, and the device is thus unusable until reboot.
Try kzalloc if we can to avoid the mapping overhead, but if that fails,
fall back to vzalloc.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c89cc17b9 upstream.
A recent patch (9d9a04ee) added support for the new machine, but got
the sequence of USB ids wrong. Reports from both Ian and Linus T show
that the 0x0291 id is for ISO, not ANSI, which should have the missing
number 0x0290. This patchs moves the three numbers accordingly, fixing
the problem.
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Tested-by: Linus G Thiel <linus@hanssonlarsson.se>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 148c1c8ad3 upstream.
The June 2013 Macbook Air (13'') has a new trackpad protocol; four new
values are inserted in the header, and the mode switch is no longer
needed. This patch adds support for the new devices.
Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input subsystem updates from Dmitry Torokhov:
"A few small fixups for cyttsp, wacom and xpad drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - fix for "Mad Catz Street Fighter IV FightPad" controllers
Input: wacom - add a new stylus (0x100802) for Intuos5 and Cintiqs
Input: add missing dependencies on CONFIG_HAS_IOMEM
Input: cyttsp - fix swapped mfg_stat and mfg_cmd registers
Input: cyttsp - add missing handshake
Input: cyttsp - fix memcpy size param
Added MAP_TRIGGERS_TO_BUTTONS for Mad Catz Street Fighter IV FightPad
device. This controller model was already supported by the xpad
driver, but none of the buttons work correctly without this change.
Tested on kernel version 3.9.5.
Signed-off-by: Shawn Joseph <jms.576@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The command and status register in the driver were swapped with
respect to the order specified in the datasheet (CY8CTMA140).
Confirmed with Cypress that the order in the datasheet is correct.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For the devices that has blocking with timeout communication, these
extra handshakes will prevent one timeout delay in startup sequence
Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
