Otherwise we allow building appletalk drivers in-kernel when
CONFIG_ATALK is modular. That doesn't work because these drivers use
symbols such as "alloc_talkdev" which is exported from code built
by CONFIG_ATALK.
Noticed by Toralf Förster.
Signed-off-by: David S. Miller <davem@davemloft.net>
Okay, Fix both typo's in one patch .The impact is that the incorrect value
was being computed for blinking LED and interrupt moderation values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always do a dummy RDMA after loading the firmware to work around
buggy PCIe chipsets which do not implement resending properly.
This is so cheap as to be almost free, and should never have been
conditional on the tx boundary != 4096.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When determining whether there's a key to set or not, orinoco should be
looking at the key length, not the key data. Otherwise confusion reigns
when trying to set TX key only, passing in zero-length key, but non-NULL
pointer. Key length takes precedence over non-NULL key data.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johann Uhrmann reported a bcm43xx crash and Michael Buesch tracked
it down to a problem with the new shared key auth code (recursive
calls into the driver)
This patch (effectively Michael's patch with a couple of small
modifications) solves the problem by sending the authentication
challenge response frame from a workqueue entry.
I also removed a lone \n from the bcm43xx messages relating to
authentication mode - this small change was previously discussed but
not patched in.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver airo (for Cisco Wlan-Cards) complains about "failed to load
transform for AES", when it is loaded and CRYPTO_AES is not selected
in Kconfig.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1201 has nasty tendency to emit magicall anti-wifi cloud when it is
inserted into slot, but not used.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle dev_alloc_skb() failures when initializing the RX rings.
Without proper handling, the driver will crash when using a partial
ring.
Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and
providing the initial patch.
Howie Xu <howie@vmware.com> also reported the same issue.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_restart_hw() to handle failures when re-initializing the
device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_register_driver instead of pci_module_init. Use PCI_DEVICE macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WAN: Fixed a problem with PPP/raw HDLC/X.25 protocols not doing
netif_dormant_off() at startup.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The via-velocity driver reports incorrect speed and link detected status
as viewed by ethtool (and probably other tools). This patch fixes those
incorrect reports and prettifies a long line.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
With this patch TX queue descriptors are not chained per default any more.
The pointer to next descriptor is set only when next descriptor is prepaired
for transfer. Also the mechanism of checking wether Spider is ready has been
changed: it checks not for CARDOWNED flag in status of previous descriptor
but for a TXDMAENABLED flag in Spider's register.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When sky2 driver gets lots of received packets at once, it can get stuck.
The NAPI poll routine gets called back to keep going, but since no IRQ bits
are set it doesn't make progress.
Increase version, since this is serious enough problem that I want to be
able to tell new from old problems.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A panic was reported when receiving 1522 size packets if using
the default MTU. we should set the initial rx buffer length to the
value that e1000changemtu sets so that we can receive any packet
that would not be dropped by LPE=0.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke.jan.h.kok@intel.com>
After removing the hardware CRC stripping which causes problems with
SOL and related issues, we need to compensate for this changed size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The original suggested fix for netpoll was found to be racy on SMP
kernels. While it is highly unlikely that this race would ever be seen
in the real world due to current netpoll usage models, we implemented
this updated fix to address concerns.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
* HEAD:
[NET]: fix __sk_stream_mem_reclaim
[Bluetooth] Fix deadlock in the L2CAP layer
[Bluetooth] Let BT_HIDP depend on INPUT
[Bluetooth] Avoid NULL pointer dereference with tty->driver
[Bluetooth] Remaining transitions to use kzalloc()
[WAN]: converting generic HDLC to use netif_dormant*()
[IPV4]: Fix error handling for fib_insert_node call
[NETROM] lockdep: fix false positive
[ROSE] lockdep: fix false positive
[AX.25]: Optimize AX.25 socket list lock
[IPCOMP]: Fix truesize after decompression
[IPV6]: Use ipv6_addr_src_scope for link address sorting.
[TCP] tcp_highspeed: Fix AI updates.
[MAINTAINERS]: Add proper entry for TC classifier
[NETROM]: Drop lock before calling nr_destroy_socket
[NETROM]: Fix locking order when establishing a NETROM circuit.
[AX.25]: Fix locking of ax25 protocol function list.
[IPV6]: order addresses by scope
When the driver handles multiple packets per NAPI poll, it is
better to reload the receive ring, then tell the hardware. Otherwise,
under packet storm with flow control, the driver/hardware will degrade
down to one packet getting through per pause-exchange.
Likewise on transmit, don't wakeup until a little more than minimum
ring space is available.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The documentation says we need to wait after turning on the PHY.
Also, don't enable WOL by default.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The changes to handle suspend/resume didn't handle the case where
a dual port card has the first port down, but the second is running.
In this driver, all NAPI polling is done on the primary port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since sky2_reset gets call from sky2_resume it shouldn't be tagged
with devinit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in (same problem
as sky2 driver). Should be three bits wide, but the mask only allows
for 1 bit to be set.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in (same problem
as sky2 driver). Should be three bits wide, but the mask only allows
for 1 bit to be set.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in sky2 driver. Should be
three bits wide, but the mask only allows for 1 bit to be set.
Thanks & Regards
Neil
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
sky2.h | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton wrote:
> All these functions return error codes, and we're not checking them. We
> should. So there's a patch which marks all these things as __must_check,
> which causes around 1,500 new warnings.
>
The following patch fixes such a warning in myri10ge.
Check pci_enable_device() return value in myri10ge_resume().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There were some tso bugs that only showed up with heavy load and 16kB
pages that this patch fixes by making the driver's internal use count
of descriptors match the count that it was estimating it needed using
the DESC_NEEDED macro. This bug caused NETDEV_WATCHDOG resets aka
tx timeouts.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
subsystem_configurations array is only used by an __init function,
therefore it should be marked __initdata, not __devinitdata.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/8139cp.c: In function 'cp_init_one':
drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modification and bug fixes with respect to irq registration.
- Enable interrupts after request_irq
- Restored MSI data register value at driver unload time
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch defines the watermark registers and fixes up the use of this
register.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the definition for the deferral registers and fixes up
the use of these registers.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts generic HDLC (and WAN drivers using it) from
hdlc_set_carrier() to netif_dormant*() interface.
WAN hardware drivers should now use netif_carrier_on|off() like
other network drivers.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bpqether is encapsulating AX.25 frames into ethernet frames. There is a
virtual bpqether device paired with each ethernet devices, so it's normal
to pass through dev_queue_xmit twice for each frame which triggers the
locking detector.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
