dts: add dtb file to makefile

arch/arm/dts/Makefile

@@ -1100,7 +1100,9 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp15xx-dhcom-pdk2.dtb \
 	stm32mp15xx-dhcom-picoitx.dtb \
 	stm32mp15xx-dhcor-avenger96.dtb \
-	stm32mp157a-panguboard.dtb
+	stm32mp157a-panguboard.dtb \
+	stm32mp157a-dthr.dtb \
+	stm32mp151a-dthr.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
 dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \

arch/arm/dts/stm32mp151a-dthr-u-boot.dtsi

@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright : STMicroelectronics 2018
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c3 = &i2c4;
+		usb0 = &usbotg_hs;
+	};
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+		u-boot,mmc-env-partition = "u-boot-env";
+		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
+		st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	};
+
+#if defined(CONFIG_STM32MP15x_STM32IMAGE) || defined(CONFIG_SPL)
+	config {
+		u-boot,mmc-env-partition = "ssbl";
+	};
+#endif
+
+	reserved-memory {
+		u-boot,dm-spl;
+
+		optee@de000000 {
+			u-boot,dm-spl;
+		};
+	};
+
+	led {
+		led-red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+#ifndef CONFIG_TFABOOT
+&clk_hse {
+	st,digbypass;
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+#endif
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
+

arch/arm/dts/stm32mp151a-dthr.dts

@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp151a-dthr.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
+	compatible = "st,stm32mp157a-dk1", "st,stm32mp157";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};

arch/arm/dts/stm32mp151a-dthr.dtsi

@@ -0,0 +1,719 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp15-m4-srm.dtsi"
+#include "stm32mp15-m4-srm-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart7;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcu_rsc_table: mcu_rsc_table@10048000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10048000 0x8000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu@d4000000 {
+			reg = <0xd4000000 0x4000000>;
+			no-map;
+		};
+
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led-blue {
+			label = "heartbeat";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+/*
+	sound: sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP15-DK";
+		routing =
+			"Playback" , "MCLK",
+			"Capture" , "MCLK",
+			"MICL" , "Mic Bias";
+		dais = <&sai2a_port &sai2b_port &i2s2_port>;
+		status = "okay";
+	};
+*/
+/*
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+*/
+	vddcore: regulator-vddcore {
+		compatible = "regulator-fixed";
+		regulator-name = "vddcore";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	v3v3: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	vdd: regulator-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	vdd_usb: regulator-vdd-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_usb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	wifi-module {
+		//power-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+		wifi-reg-gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>;
+		bt-reg-gpios = <&gpiof 12 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+	adc1: adc@0 {
+		status = "okay";
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+	adc2: adc@100 {
+		status = "okay";
+		/* USB Type-C CC1 & CC2 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_sleep_pins_b>;
+	status = "okay";
+};
+
+&cpu0{
+	cpu-supply = <&vddcore>;
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dma1 {
+	sram = <&dma_pool>;
+};
+
+&dma2 {
+	sram = <&dma_pool>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	snps,reset-gpio = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+	/*nvmem-cells = <&ethernet_mac_address>;
+	nvmem-cell-names = "mac-address";*/
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+/*
+	hdmi-transmitter@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		iovcc-supply = <&v3v3_hdmi>;
+		cvcc12-supply = <&v1v2_hdmi>;
+		reset-gpios = <&gpioa 10 GPIO_ACTIVE_LOW>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+		#sound-dai-cells = <0>;
+		status = "okay";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sii9022_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				sii9022_tx_endpoint: endpoint {
+					remote-endpoint = <&i2s2_endpoint>;
+				};
+			};
+		};
+	};
+
+	cs42l51: cs42l51@4a {
+		compatible = "cirrus,cs42l51";
+		reg = <0x4a>;
+		#sound-dai-cells = <0>;
+		VL-supply = <&v3v3>;
+		VD-supply = <&v1v8_audio>;
+		VA-supply = <&v1v8_audio>;
+		VAHP-supply = <&v1v8_audio>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		clocks = <&sai2a>;
+		clock-names = "MCLK";
+		status = "okay";
+
+		cs42l51_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cs42l51_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&cs42l51_tx_endpoint>;
+				bitclock-master = <&cs42l51_tx_endpoint>;
+			};
+
+			cs42l51_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&cs42l51_rx_endpoint>;
+				bitclock-master = <&cs42l51_rx_endpoint>;
+			};
+		};
+	};
+*/
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+/*
+	stusb1600@28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+		status = "okay";
+		vdd-supply = <&vin>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			typec-power-opmode = "default";
+
+			port {
+				con_usbotg_hs_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+*/
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_sleep_pins_a>;
+	status = "okay";
+/*
+	i2s2_port: port {
+		i2s2_endpoint: endpoint {
+			remote-endpoint = <&sii9022_tx_endpoint>;
+			format = "i2s";
+			mclk-fs = <256>;
+		};
+	};
+*/
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-1 = <&ltdc_sleep_pins_a>;
+	status = "okay";
+/*
+	port {
+		ltdc_ep0_out: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+*/
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>, <&mcu_rsc_table>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	wakeup-source;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	/*pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>;*/
+	status = "okay";
+
+/*
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		status = "okay";
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&cs42l51_tx_endpoint>;
+				format = "i2s";
+				mclk-fs = <256>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&cs42l51_rx_endpoint>;
+				format = "i2s";
+				mclk-fs = <256>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+			};
+		};
+	};
+	*/
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	/*cd-gpios = <&gpioh 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;*/
+	non-removable;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	/*st,neg-edge;*/
+	keep-power-in-suspend;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "disabled";
+};
+
+&spi4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi4_pins_b>;
+	pinctrl-1 = <&spi4_sleep_pins_b>;
+	status = "disabled";
+};
+
+&spi5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi5_pins_a>;
+	pinctrl-1 = <&spi5_sleep_pins_a>;
+	status = "disabled";
+};
+
+&sram {
+	dma_pool: dma_pool@0 {
+		reg = <0x50000 0x10000>;
+		pool;
+	};
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer@5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart7_pins_c>;
+	pinctrl-1 = <&uart7_sleep_pins_c>;
+	pinctrl-2 = <&uart7_idle_pins_c>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_c>;
+	pinctrl-1 = <&usart3_sleep_pins_c>;
+	pinctrl-2 = <&usart3_idle_pins_c>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+/*
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usbotg_hs_ep>;
+		};
+	};
+*/
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+
+	/*
+	 * Hack to keep hub active until all connected devices are suspended
+	 * otherwise the hub will be powered off as soon as the v3v3 is disabled
+	 * and it can disturb connected devices.
+	 */
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&v3v3>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};

arch/arm/dts/stm32mp157a-dthr-u-boot.dtsi

@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright : STMicroelectronics 2018
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c3 = &i2c4;
+		usb0 = &usbotg_hs;
+	};
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+		u-boot,mmc-env-partition = "u-boot-env";
+		st,adc_usb_pd = <&adc1 18>, <&adc1 19>;
+		st,fastboot-gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		st,stm32prog-gpios = <&gpioa 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	};
+
+#if defined(CONFIG_STM32MP15x_STM32IMAGE) || defined(CONFIG_SPL)
+	config {
+		u-boot,mmc-env-partition = "ssbl";
+	};
+#endif
+
+	reserved-memory {
+		u-boot,dm-spl;
+
+		optee@de000000 {
+			u-boot,dm-spl;
+		};
+	};
+
+	led {
+		led-red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+#ifndef CONFIG_TFABOOT
+&clk_hse {
+	st,digbypass;
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4R
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll@1 {
+		compatible = "st,stm32mp1-pll";
+		reg = <1>;
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll@2 {
+		compatible = "st,stm32mp1-pll";
+		reg = <2>;
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+	pll4: st,pll@3 {
+		compatible = "st,stm32mp1-pll";
+		reg = <3>;
+		cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+#endif
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
+

arch/arm/dts/stm32mp157a-dthr.dts

@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xa.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp157a-dthr.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
+	compatible = "st,stm32mp157a-dk1", "st,stm32mp157c-dk2", "st,stm32mp157";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};

arch/arm/dts/stm32mp157a-dthr.dtsi

@@ -0,0 +1,731 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp15-m4-srm.dtsi"
+#include "stm32mp15-m4-srm-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+//#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart7;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcu_rsc_table: mcu_rsc_table@10048000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10048000 0x8000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu@d4000000 {
+			reg = <0xd4000000 0x4000000>;
+			no-map;
+		};
+
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led-blue {
+			label = "heartbeat";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+/*
+	sound: sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP15-DK";
+		routing =
+			"Playback" , "MCLK",
+			"Capture" , "MCLK",
+			"MICL" , "Mic Bias";
+		dais = <&sai2a_port &sai2b_port &i2s2_port>;
+		status = "okay";
+	};
+*/
+/*
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+*/
+	vddcore: regulator-vddcore {
+		compatible = "regulator-fixed";
+		regulator-name = "vddcore";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	v3v3: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	vdd: regulator-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	vdd_usb: regulator-vdd-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_usb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-off-in-suspend;
+		regulator-always-on;
+	};
+
+	wifi-module {
+		//power-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+		wifi-reg-gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>;
+		bt-reg-gpios = <&gpiof 12 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "disabled";
+	adc1: adc@0 {
+		status = "disabled";
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+	adc2: adc@100 {
+		status = "disabled";
+		/* USB Type-C CC1 & CC2 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_sleep_pins_b>;
+	status = "okay";
+};
+
+&cpu0{
+	cpu-supply = <&vddcore>;
+};
+
+&cpu1{
+	cpu-supply = <&vddcore>;
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dma1 {
+	sram = <&dma_pool>;
+};
+
+&dma2 {
+	sram = <&dma_pool>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <10000 15000 50000>;
+	snps,reset-gpio = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+	/*
+	nvmem-cells = <&ethernet_mac_address>;
+	nvmem-cell-names = "mac-address";
+	*/
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+/*
+	hdmi-transmitter@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		iovcc-supply = <&v3v3_hdmi>;
+		cvcc12-supply = <&v1v2_hdmi>;
+		reset-gpios = <&gpioa 10 GPIO_ACTIVE_LOW>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+		#sound-dai-cells = <0>;
+		status = "okay";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sii9022_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				sii9022_tx_endpoint: endpoint {
+					remote-endpoint = <&i2s2_endpoint>;
+				};
+			};
+		};
+	};
+
+	cs42l51: cs42l51@4a {
+		compatible = "cirrus,cs42l51";
+		reg = <0x4a>;
+		#sound-dai-cells = <0>;
+		VL-supply = <&v3v3>;
+		VD-supply = <&v1v8_audio>;
+		VA-supply = <&v1v8_audio>;
+		VAHP-supply = <&v1v8_audio>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		clocks = <&sai2a>;
+		clock-names = "MCLK";
+		status = "okay";
+
+		cs42l51_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cs42l51_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&cs42l51_tx_endpoint>;
+				bitclock-master = <&cs42l51_tx_endpoint>;
+			};
+
+			cs42l51_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&cs42l51_rx_endpoint>;
+				bitclock-master = <&cs42l51_rx_endpoint>;
+			};
+		};
+	};
+*/
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+/*
+	stusb1600@28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+		status = "okay";
+		vdd-supply = <&vin>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			typec-power-opmode = "default";
+
+			port {
+				con_usbotg_hs_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+*/
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_sleep_pins_a>;
+	status = "okay";
+/*
+	i2s2_port: port {
+		i2s2_endpoint: endpoint {
+			remote-endpoint = <&sii9022_tx_endpoint>;
+			format = "i2s";
+			mclk-fs = <256>;
+		};
+	};
+*/
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-1 = <&ltdc_sleep_pins_a>;
+	status = "okay";
+/*
+	port {
+		ltdc_ep0_out: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+*/
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>, <&mcu_rsc_table>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	wakeup-source;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	/*pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>;*/
+	status = "okay";
+
+/*
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		status = "okay";
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&cs42l51_tx_endpoint>;
+				format = "i2s";
+				mclk-fs = <256>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&cs42l51_rx_endpoint>;
+				format = "i2s";
+				mclk-fs = <256>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+			};
+		};
+	};
+	*/
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	/*cd-gpios = <&gpioh 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;*/
+	non-removable;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	/*st,neg-edge;*/
+	bus-width = <8>;
+	keep-power-in-suspend;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "disabled";
+};
+
+&spi4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi4_pins_b>;
+	pinctrl-1 = <&spi4_sleep_pins_b>;
+	status = "disabled";
+};
+
+&spi5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi5_pins_a>;
+	pinctrl-1 = <&spi5_sleep_pins_a>;
+	status = "disabled";
+};
+
+&sram {
+	dma_pool: dma_pool@0 {
+		reg = <0x50000 0x10000>;
+		pool;
+	};
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer@5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart7_pins_c>;
+	pinctrl-1 = <&uart7_sleep_pins_c>;
+	pinctrl-2 = <&uart7_idle_pins_c>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_c>;
+	pinctrl-1 = <&usart3_sleep_pins_c>;
+	pinctrl-2 = <&usart3_idle_pins_c>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+/*
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usbotg_hs_ep>;
+		};
+	};
+*/
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+
+	/*
+	 * Hack to keep hub active until all connected devices are suspended
+	 * otherwise the hub will be powered off as soon as the v3v3 is disabled
+	 * and it can disturb connected devices.
+	 */
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&v3v3>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};