Add max_snk_mw property for power sink to know the max power.
Because the max mw may be smaller than the max ma multiplied by
max mv:
max-mw <= max-mv*max-ma
After the power sink decides the PDO from source, it needs
to check the power to see if the provided power of this PDO
can match its requirement, which needs consider max_snk_mw to
know the max current it can have based on selected voltage.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Some chipidea hardware needs to disable low power mode for controller
due to IC issue or hardware issue, add one quirk for it.
Acked-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
There is already one quirk for usb3 xhci flag XHCI_MISSING_CAS, for
those platform with OF we can use usb3-resume-missing-cas to enable
this quirk to work around usb3 resume from system sleep.
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
TCPCI stands for typec port controller interface, its implementation
has full typec port control with power delivery support, it's a
standard i2c slave with GPIO input as irq interface, detail see spec
"Universal Serial Bus Type-C Port Controller Interface Specification
Revision 1.0, Version 1.1"
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
port-type is required for any typec port; default-role is only required
for drp; power source capable needs src-pdos; power sink capable needs
snk-pdos, max-snk-mv, max-snk-ma, op-snk-mw.
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Add dt documentation for specify the suspend clk and its caculation.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
USB host vbus control can be via port power(PP) bit of ehci, there
is a polarity setting in controller register for this signal, if
power supply chip use active high, add this property.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
imx7ulp non core register mapping is similar with imx7d, and the
initialization is the same, but lacks of USB charger detection support.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
It is used to indicate whether we use SoC's usb charger
detection or not. Besides, we add anatop phandle since
we need to use anatop register to do most of charger detect operations.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
[ Upstream commit f42ae7b054 ]
The USB hub port-number range for USB 2.0 is 1-255 and not 1-31 which
reflects an arbitrary limit set by the current Linux implementation.
Note that for USB 3.1 hubs the valid range is 1-15.
Increase the documented valid range in the binding to 255, which is the
maximum allowed by the specifications.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull DeviceTree updates from Rob Herring:
"There's a few orphans in the conversion to %pOF printf specifiers
included here that no one else picked up.
Summary:
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans
- Correct unittests to use preferred "okay" for "status" property
value
- Add a KASLR seed property
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa
- Fix modalias buffer handling
- Clean-up of include paths for building dtbs
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10
devices
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC
- Add compatible string for Allwinner H5 Mali-450 GPU
- Fix links to old OpenFirmware docs with new mirror on
devicetree.org
- Remove status property from binding doc examples"
* tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
devicetree: Adjust status "ok" -> "okay" under drivers/of/
dt-bindings: Remove "status" from examples
dt-bindings: pinctrl: sh-pfc: Use generic node name
dt-bindings: Add vendor Mellanox
dt-binding: net/phy: fix interrupts description
virt: Convert to using %pOF instead of full_name
macintosh: Convert to using %pOF instead of full_name
ide: pmac: Convert to using %pOF instead of full_name
microblaze: Convert to using %pOF instead of full_name
dt-bindings: usb: musb: Grammar s/the/to/, s/is/are/
of: Use PLATFORM_DEVID_NONE definition
of/device: Fix of_device_get_modalias() buffer handling
of/device: Prevent buffer overflow in of_device_modalias()
dt-bindings: add amc6821, isl1208 trivial bindings
dt-bindings: add vendor prefix for Theobroma Systems
of: search scripts/dtc/include-prefixes path for both CPP and DTC
of: remove arch/$(SRCARCH)/boot/dts from include search path for CPP
of: remove drivers/of/testcase-data from include search path for CPP
of: return of_get_cpu_node from of_cpu_device_node_get if CPUs are not registered
iio: srf08: add device tree binding for srf02 and srf10
...
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver update for 4.14-rc1.
Lots of staging driver fixes and cleanups, including some reorginizing
of the lustre header files to try to impose some sanity on what is,
and what is not, the uapi for that filesystem.
There are some tty core changes in here as well, as the speakup
drivers need them, and that's ok with me, they are sane and the
speakup code is getting nicer because of it.
There is also the addition of the obiligatory new wifi driver, just
because it has been a release or two since we added our last one...
Other than that, lots and lots of small coding style fixes, as usual.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (612 commits)
staging:rtl8188eu:core Fix remove unneccessary else block
staging: typec: fusb302: make structure fusb302_psy_desc static
staging: unisys: visorbus: make two functions static
staging: fsl-dpaa2/eth: fix off-by-one FD ctrl bitmaks
staging: r8822be: Simplify deinit_priv()
staging: r8822be: Remove some dead code
staging: vboxvideo: Use CONFIG_DRM_KMS_FB_HELPER to check for fbdefio availability
staging:rtl8188eu Fix comparison to NULL
staging: rts5208: rename mmc_ddr_tunning_rx_cmd to mmc_ddr_tuning_rx_cmd
Staging: Pi433: style fix - tabs and spaces
staging: pi433: fix spelling mistake: "preample" -> "preamble"
staging:rtl8188eu:core Fix Code Indent
staging: typec: fusb302: Export current-limit through a power_supply class dev
staging: typec: fusb302: Add support for USB2 charger detection through extcon
staging: typec: fusb302: Use client->irq as irq if set
staging: typec: fusb302: Get max snk mv/ma/mw from device-properties
staging: typec: fusb302: Set max supply voltage to 5V
staging: typec: tcpm: Add get_current_limit tcpc_dev callback
staging:rtl8188eu Use __func__ instead of function name
staging: lustre: coding style fixes found by checkpatch.pl
...
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This is board specific info so it should come from board config, such
as devicetree.
I've chosen to prefix these with "fcs," treating them as fusb302 driver
specific for now. We may want to revisit this and replace these with
properties which are part of a (to be written) generic type-c controller
devicetree binding.
Since this commit adds new dt-properties it also adds devicetree-bindings
documentation (which so far was absent for the fusb302 driver).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mt8173-mtu3.txt actually holds the bindings for all mediatek
SoCs with usb3 DRD IP, so add a generic compatible and change the
name to mediatek,mtu3.txt.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mt8173-xhci.txt actually holds the bindings for all mediatek
SoCs with xHCI controller, so add a generic compatible and change
the name to mediatek,mtk-xhci.txt to reflect that.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update various properties to properly indicate their requirement depending
on the SoC.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car M3-W. This patch also adds R-Car
Gen3 generic version's compatible and changes ".compatible" in
the usb3_of_match from "renesas,r8a7796-usb3-peri" to
"renesas,rcar-gen3-usb3-peri".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull DeviceTree updates from Rob Herring:
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
of: document /sys/firmware/fdt
dt-bindings: Add RISC-V vendor prefix
vsprintf: Add %p extension "%pOF" for device tree
of: find_node_by_full_name rewrite to compare each level
of: use kbasename instead of open coding
dt-bindings: thermal: add file extension to brcm,ns-thermal
of: update ePAPR references to point to Devicetree Specification
scripts/dtc: dtx_diff - Show real file names in diff header
of: detect invalid phandle in overlay
of: be consistent in form of file mode
of: make __of_attach_node() static
of: address.c header comment typo
of: fdt.c header comment typo
of: make of_fdt_is_compatible() static
dt-bindings: display-timing.txt convert non-ascii characters to ascii
Documentation: remove overlay-notes reference to non-existent file
dt-bindings: usb: exynos-usb: Add missing required VDD properties
dt-bindings: Add vendor prefix for Linksys
MAINTAINERS: add device tree ABI documentation file
of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
...
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
Since commit bd8ce544ec ("usb: dwc3: exynos: Make provision for vdd
regulators") vdd33-supply and vdd10-supply are required so document them
in bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The device node is used for UDCs integrated into Broadcom's
iProc family of SoCs'. The UDC is based on Synopsys Designware
Cores AHB Subsystem USB Device Controller IP.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull dmaengine updates from Vinod Koul:
"This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor,
ioat, dmatest"
* tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (35 commits)
dmaengine: pl08x: remove lock documentation
dmaengine: pl08x: fix pl08x_dma_chan_state documentation
dmaengine: pl08x: Use the BIT() macro consistently
dmaengine: pl080: Fix some missing kerneldoc
dmaengine: pl080: Cut some unused defines
dmaengine: dmatest: Add check for supported buffer count (sg_buffers)
dmaengine: dmatest: Select DMA_ENGINE_RAID as its needed for the slave_sg test
dmaengine: virt-dma: Convert to use list_for_each_entry_safe()
dma-debug: use offset_in_page() macro
dmaengine: mv_xor: use offset_in_page() macro
dmaengine: dmatest: use offset_in_page() macro
dmaengine: sun4i: fix invalid argument
dmaengine: ioat: use setup_timer
dmaengine: cppi41: Fix an Oops happening in cppi41_dma_probe()
dmaengine: pl330: remove pdata based initialization
dmaengine: cppi: fix build error due to bad variable
dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
dmaengine: cppi41: use managed functions devm_*()
dmaengine: cppi41: fix cppi41_dma_tx_status() logic
dmaengine: qcom_hidma: pause the channel on shutdown
...
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
STM32 DT updates for v4.12, round 1
Highlights:
----------
- ADD RTC support on STM32F746 MCU
- Enable RTC on STM32F746 Eval board
- Enable clocks on STM32F746 MCU
- Enable DMA, pwm1 and pwm3 on STM32F429I Eval
- Add support of STM32H743 MCU and his Eval board
- Enable USB HS and FS on STM32F469 Disco board
* tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
dt-bindings: Document the STM32 USB OTG DWC2 core binding
ARM: dts: stm32: Enable USB HS in FS mode (embedded phy) on stm32f429-disco
ARM: dts: stm32: Enable USB FS on stm32f469-disco
ARM: dts: stm32: Add USB FS support for STM32F429 MCU
ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL board
ARM: dts: stm32: Enable pwm1 and pwm3 on stm32f429i-eval
ARM: dts: stm32: Enable dma by default on stm32f4 adc
ARM: dts: stm32: enable RTC on stm32746g-eval
ARM: dts: stm32: Add RTC support for STM32F746 MCU
ARM: dts: stm32: set HSE_RTC clock frequency to 1 MHz on stm32f746
dt-bindings: mfd: Add STM32F7 RCC numeric constants into DT include file
ARM: dts: stm32: Enable clocks for STM32F746 MCU
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add a new compatible string for the Armada 3700 SoCs
- add sbuscfg support for orion usb controller driver. For the SoCs
without hlock, need to program BAWR/BARD/AHBBRST fields in the sbuscfg
register to guarantee the AHB master's burst would not overrun or
underrun the FIFO.
- the sbuscfg register has to be set after the usb controller reset,
otherwise the value would be overridden to 0. In order to do this, the
reset callback is registered.
[gregory.clement@free-electrons.com: - reword commit and comments
- fix error path in ehci_orion_drv_reset()
- fix checkpatch warning]
Signed-off-by: Hua Jing <jinghua@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI controllers will have a companion controller. However, on platform
bus, there was difficult to bind them in previous code. So, this
patch adds helper functions to bind them using a "companion" property.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark the reg property as required and furthermore fix some typos and
spellings in the documentation.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull DeviceTree updates from Rob Herring:
"Pretty standard stuff with dtc upstream sync being the biggest piece.
- Sync dtc to upstream commit 0931cea3ba20. This picks up overlay
support in dtc.
- Set dma_ops for reserved memory users.
- Make references to IOMMU consistent in DT bindings.
- Cleanup references to pm_power_off in bindings.
- Move some display bindings that snuck into the old bindings/video/
path.
- Fix some wrong documentation paths caused from binding
restructuring.
- Vendor prefixes for Faraday and Fujitsu.
- Fix an of_node ref counting leak in of_find_node_opts_by_path
- Introduce new graph helper of_graph_get_remote_node() which will be
used by DRM drivers in 4.12"
* tag 'devicetree-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (27 commits)
DT: add Faraday Tec. as vendor
of: introduce of_graph_get_remote_node
of: Add missing space at end of pr_fmt().
of: make of_device_make_bus_id() static
of: fix of_node leak caused in of_find_node_opts_by_path
dt-bindings: net: remove reference to fixed link support
dt-bindings: power: reset: qnap-poweroff: Drop reference to pm_power_off
dt-bindings: power: reset: gpio-poweroff: Drop reference to pm_power_off
dt-bindings: mfd: as3722: Drop reference to pm_power_off
dt-bindings: display: move ANX7814 and SiI8620 bridge bindings
of/unittest: Swap arguments of of_unittest_apply_overlay()
Documentation: usb: fix wrong documentation paths
serial: fsl-imx-uart.txt: Remove generic property
devicetree: Add Fujitsu Ltd. vendor prefix
Documentation: display: fix wrong documentation paths
of: remove redundant memset in overlay
bus:qcom : Fix typo in qcom,ebi2.txt
dt-bindings: qman: Remove pool channel node
Documentation: panel-dpi: fix path to display-timing.txt
devicetree: bindings: clk: mvebu: fix description for sata1 on Armada XP
...
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
Furthermore add myself as a maintainer for this driver.
The datasheet can be found at the manufacturers website, see [1]. All
device-tree exposed configuration features have been tested on a i.MX6
platform with a USB2512B hub.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00001692C.pdf
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter writes:
Hi Greg,
In this series, it adds qualcomm USB2 support. The review process takes
more than half of year, thanks for Stephen Boyd's great work.
Most of patches at linux-next more than ten days, and the last two small
chipidea patches at my tree about one day, no warning is reported from
autobuild robot.
Thanks.
Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
