commit 7935799e04 upstream.
Clang warns:
../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
if (oparms->tcon->use_resilient) {
^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
if (rc)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 592fafe644 ("Add resilienthandles mount parm")
Link: https://github.com/ClangBuiltLinux/linux/issues/826
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b698c838e upstream.
I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 742d4d4083 ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1b9ae1864 upstream.
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8a66d8004 upstream.
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c57bfd52 upstream.
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b5026bc16 upstream.
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ed0a1d563 upstream.
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c2d5e33dc upstream.
hsr interface has own debugfs file, which name is same with interface name.
So, interface name is changed, debugfs file name should be changed too.
Fixes: fc4ecaeebd ("net: hsr: add debugfs support for display node list")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6c4ccd7f9 upstream.
In current hsr code, when hsr interface is created, it creates debugfs
directory /sys/kernel/debug/<interface name>.
If there is same directory or file name in there, it fails.
In order to reduce possibility of failure of creation of debugfs,
this patch adds root directory.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
Before this patch:
/sys/kernel/debug/hsr0/node_table
After this patch:
/sys/kernel/debug/hsr/hsr0/node_table
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 051172e8c1 upstream.
Commit Fixes: b9f8b09ce2 ("drm/tegra: Setup shared IOMMU domain after
initialization") changed the initialization order of the IOMMU related
bits but didn't update the cleanup path accordingly. This asymmetry can
cause failures during error recovery.
Fixes: b9f8b09ce2 ("drm/tegra: Setup shared IOMMU domain after initialization")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d935bd50dd upstream.
When a GPIO offset in a lookup table is out-of-range, the printed error
message (1) does not include the actual out-of-range value, and (2)
contains an off-by-one error in the upper bound.
Avoid user confusion by also printing the actual GPIO offset, and
correcting the upper bound of the range.
While at it, use "%u" for unsigned int.
Sample impact:
-requested GPIO 0 is out of range [0..32] for chip e6052000.gpio
+requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio
Fixes: 2a3cf6a359 ("gpiolib: return -ENOENT if no GPIO mapping exists")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191127095919.4214-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83c9c54716 upstream.
Commit 85a8ce62c2 ("block: add bio_truncate to fix guard_bio_eod")
adds bio_truncate() for handling bio EOD. However, bio_truncate()
doesn't use the passed 'op' parameter from guard_bio_eod's callers.
So bio_trunacate() may retrieve wrong 'op', and zering pages may
not be done for READ bio.
Fixes this issue by moving guard_bio_eod() after bio_set_op_attrs()
in submit_bh_wbc() so that bio_truncate() can always retrieve correct
op info.
Meantime remove the 'op' parameter from guard_bio_eod() because it isn't
used any more.
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: linux-fsdevel@vger.kernel.org
Fixes: 85a8ce62c2 ("block: add bio_truncate to fix guard_bio_eod")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fold in kerneldoc and bio_op() change.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit e10360f815 upstream.
Before commit 4bfc0bb2c6 ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
cgroup bpf structures were released with
corresponding cgroup structures. It guaranteed the hierarchical order
of destruction: children were always first. It preserved attached
programs from being released before their propagated copies.
But with cgroup auto-detachment there are no such guarantees anymore:
cgroup bpf is released as soon as the cgroup is offline and there are
no live associated sockets. It means that an attached program can be
detached and released, while its propagated copy is still living
in the cgroup subtree. This will obviously lead to an use-after-free
bug.
To reproduce the issue the following script can be used:
#!/bin/bash
CGROOT=/sys/fs/cgroup
mkdir -p ${CGROOT}/A ${CGROOT}/B ${CGROOT}/A/C
sleep 1
./test_cgrp2_attach ${CGROOT}/A egress &
A_PID=$!
./test_cgrp2_attach ${CGROOT}/B egress &
B_PID=$!
echo $$ > ${CGROOT}/A/C/cgroup.procs
iperf -s &
S_PID=$!
iperf -c localhost -t 100 &
C_PID=$!
sleep 1
echo $$ > ${CGROOT}/B/cgroup.procs
echo ${S_PID} > ${CGROOT}/B/cgroup.procs
echo ${C_PID} > ${CGROOT}/B/cgroup.procs
sleep 1
rmdir ${CGROOT}/A/C
rmdir ${CGROOT}/A
sleep 1
kill -9 ${S_PID} ${C_PID} ${A_PID} ${B_PID}
On the unpatched kernel the following stacktrace can be obtained:
[ 33.619799] BUG: unable to handle page fault for address: ffffbdb4801ab002
[ 33.620677] #PF: supervisor read access in kernel mode
[ 33.621293] #PF: error_code(0x0000) - not-present page
[ 33.622754] Oops: 0000 [#1] SMP NOPTI
[ 33.623202] CPU: 0 PID: 601 Comm: iperf Not tainted 5.5.0-rc2+ #23
[ 33.625545] RIP: 0010:__cgroup_bpf_run_filter_skb+0x29f/0x3d0
[ 33.635809] Call Trace:
[ 33.636118] ? __cgroup_bpf_run_filter_skb+0x2bf/0x3d0
[ 33.636728] ? __switch_to_asm+0x40/0x70
[ 33.637196] ip_finish_output+0x68/0xa0
[ 33.637654] ip_output+0x76/0xf0
[ 33.638046] ? __ip_finish_output+0x1c0/0x1c0
[ 33.638576] __ip_queue_xmit+0x157/0x410
[ 33.639049] __tcp_transmit_skb+0x535/0xaf0
[ 33.639557] tcp_write_xmit+0x378/0x1190
[ 33.640049] ? _copy_from_iter_full+0x8d/0x260
[ 33.640592] tcp_sendmsg_locked+0x2a2/0xdc0
[ 33.641098] ? sock_has_perm+0x10/0xa0
[ 33.641574] tcp_sendmsg+0x28/0x40
[ 33.641985] sock_sendmsg+0x57/0x60
[ 33.642411] sock_write_iter+0x97/0x100
[ 33.642876] new_sync_write+0x1b6/0x1d0
[ 33.643339] vfs_write+0xb6/0x1a0
[ 33.643752] ksys_write+0xa7/0xe0
[ 33.644156] do_syscall_64+0x5b/0x1b0
[ 33.644605] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by grabbing a reference to the bpf structure of each ancestor
on the initialization of the cgroup bpf structure, and dropping the
reference at the end of releasing the cgroup bpf structure.
This will restore the hierarchical order of cgroup bpf releasing,
without adding any operations on hot paths.
Thanks to Josef Bacik for the debugging and the initial analysis of
the problem.
Fixes: 4bfc0bb2c6 ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
Reported-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7e3f63d7 upstream.
The loopback feature is only supported on a few drivers like broadcom,
mellanox, etc. The default veth driver has not supported it yet. To avoid
returning failed and making the runner feel confused, let's just skip
the test on drivers that not support loopback.
Fixes: ad11340994 ("selftests: Add loopback test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35c60be220 upstream.
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcf08d0f8f upstream.
dsp_box is used to keep DSP initiated messages. The value of dsp_offset
is set by the DSP with the first message, so we need a way to bootstrap
it in order to get the first message.
We do this by setting the correct default dsp_box offset which on i.MX8
is not zero.
Very interesting is why it has worked until now.
On i.MX8, DSP communicates with ARM core using a shared SDRAM memory
area. Actually, there are two shared areas:
* SDRAM0 - starting at 0x92400000, size 0x800000
* SDRAM1 - starting at 0x92C00000, size 0x800000
SDRAM0 keeps the data sections, starting with .rodata. By chance
fw_ready structure was placed at the beginning of .rodata.
dsp_box_base is defined as SDRAM0 + dsp_box_offset and it is placed
at the beginning of SDRAM1 (dsp_box_offset should be 0x800000). But
because it is zero initialized by default it points to SDRAM0 where
by chance the fw_ready was placed in the SOF firmware.
Anyhow, SOF commit 7466bee378dd811b ("clk: make freq arrays constant")
fw_ready is no longer at the beginning of SDRAM0 and everything shows
how lucky we were until now.
Fix this by properly setting the default dsp_box offset.
Fixes: 202acc565a ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220170531.10423-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e36e1894 upstream.
In a rare randconfig build I came across one configuration that does
not enable CONFIG_GPIOLIB, which is needed by lochnagar:
ERROR: "devm_gpiochip_add_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_free" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_request" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_get_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
Add another 'select' like all other pinctrl drivers have.
Fixes: 0548448b71 ("pinctrl: lochnagar: Add support for the Cirrus Logic Lochnagar")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191218163701.171914-1-arnd@arndb.de
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b7658679d upstream.
Changing input state in iec capture control is not safe,
as the pin state may be changed concurrently by ASoC
framework.
Remove pin state handling in iec capture control.
Note: This introduces a restriction on capture control,
when pin sleep state is defined in device tree. In this case
channel status can be captured only when an audio stream
capture is active.
Fixes: f68c2a682d ("ASoC: stm32: spdifrx: add power management")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-4-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2859b17840 upstream.
In current spdifrx driver locks may be requested as follows:
- request lock on iec capture control, when starting synchronization.
- request lock in interrupt context, when spdifrx stop is called
from IRQ handler.
Take lock with IRQs disabled, to avoid the possible deadlock.
Lockdep report:
[ 74.278059] ================================
[ 74.282306] WARNING: inconsistent lock state
[ 74.290120] --------------------------------
...
[ 74.314373] CPU0
[ 74.314377] ----
[ 74.314381] lock(&(&spdifrx->lock)->rlock);
[ 74.314396] <Interrupt>
[ 74.314400] lock(&(&spdifrx->lock)->rlock);
Fixes: 03e4d5d56f ("ASoC: stm32: Add SPDIFRX support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-2-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b722da667 upstream.
The commit bebff81fb8 ("i2c: bcm2835: Model Divider in CCF") introduced
a NULL pointer dereference on driver unload. It seems that we can't fetch
the bus clock via devm_clk_get in bcm2835_i2c_remove. As an alternative
approach store a pointer to the bus clock in the private driver structure.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4114b17af4 upstream.
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca9033ba69 upstream.
In the iowait structure, two iowait_work entries were included to queue a
given object: one for normal IB operations, and the other for TID RDMA
operations. For non-TID RDMA operations, the iowait_work structure for TID
RDMA is initialized to contain a NULL function (not used). When the QP is
reset, the function iowait_cancel_work will be called to cancel any
pending work. The problem is that this function will call
cancel_work_sync() for both iowait_work entries, even though the one for
TID RDMA is not used at all. Eventually, the call cascades to
__flush_work(), wherein a WARN_ON will be triggered due to the fact that
work->func is NULL.
The WARN_ON was introduced in commit 4d43d395fe ("workqueue: Try to
catch flush_work() without INIT_WORK().")
This patch fixes the issue by making sure that a work function is present
for TID RDMA before calling cancel_work_sync in iowait_cancel_work.
Fixes: 4d43d395fe ("workqueue: Try to catch flush_work() without INIT_WORK().")
Fixes: 5da0fc9dbf ("IB/hfi1: Prepare resource waits for dual leg")
Link: https://lore.kernel.org/r/20191219211941.58387.39883.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c527572358 upstream.
Some adapters need a fence Work Entry to handle retransmission. Currently
the driver checks for this condition, only if the Send queue entry is
signalled. Implement the condition check, irrespective of the signalled
state of the Work queue entries
Failure to add the fence can result in access to memory that is already
marked as completed, triggering data corruption, transmission failure,
IOMMU failures, etc.
Fixes: 9152e0b722 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Link: https://lore.kernel.org/r/1574671174-5064-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e635c2851 ]
hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e7461f ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc1d ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc8a76a152 upstream.
Intel ID: PSIRT-TA-201910-001
CVEID: CVE-2019-14615
Intel GPU Hardware prior to Gen11 does not clear EU state
during a context switch. This can result in information
leakage between contexts.
For Gen8 and Gen9, hardware provides a mechanism for
fast cleardown of the EU state, by issuing a PIPE_CONTROL
with bit 27 set. We can use this in a context batch buffer
to explicitly cleardown the state on every context switch.
As this workaround is already in place for gen8, we can borrow
the code verbatim for Gen9.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22dad713b8 upstream.
The set uadt functions assume lineno is never NULL, but it is in
case of ip_set_utest().
syzkaller managed to generate a netlink message that calls this with
LINENO attr present:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:hash_mac4_uadt+0x1bc/0x470 net/netfilter/ipset/ip_set_hash_mac.c:104
Call Trace:
ip_set_utest+0x55b/0x890 net/netfilter/ipset/ip_set_core.c:1867
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
nfnetlink_rcv+0x1ba/0x460 net/netfilter/nfnetlink.c:563
pass a dummy lineno storage, its easier than patching all set
implementations.
This seems to be a day-0 bug.
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Reported-by: syzbot+34bd2369d38707f3f4a7@syzkaller.appspotmail.com
Fixes: a7b4f989a6 ("netfilter: ipset: IP set core support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d9a7acd3d upstream.
The timeout pointer can be NULL which means we should modify the
per-nets timeout instead.
All do this, except sctp and dccp which instead give:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
net/netfilter/nf_conntrack_proto_dccp.c:682
ctnl_timeout_parse_policy+0x150/0x1d0 net/netfilter/nfnetlink_cttimeout.c:67
cttimeout_default_set+0x150/0x1c0 net/netfilter/nfnetlink_cttimeout.c:368
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
Reported-by: syzbot+46a4ad33f345d1dd346e@syzkaller.appspotmail.com
Fixes: c779e84960 ("netfilter: conntrack: remove get_timeout() indirection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b789577f6 upstream.
We get crash when the targets checkentry function tries to make
use of the network namespace pointer for arptables.
When the net pointer got added back in 2010, only ip/ip6/ebtables were
changed to initialize it, so arptables has this set to NULL.
This isn't a problem for normal arptables because no existing
arptables target has a checkentry function that makes use of par->net.
However, direct users of the setsockopt interface can provide any
target they want as long as its registered for ARP or UNPSEC protocols.
syzkaller managed to send a semi-valid arptables rule for RATEEST target
which is enough to trigger NULL deref:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: xt_rateest_tg_checkentry+0x11d/0xb40 net/netfilter/xt_RATEEST.c:109
[..]
xt_check_target+0x283/0x690 net/netfilter/x_tables.c:1019
check_target net/ipv4/netfilter/arp_tables.c:399 [inline]
find_check_entry net/ipv4/netfilter/arp_tables.c:422 [inline]
translate_table+0x1005/0x1d70 net/ipv4/netfilter/arp_tables.c:572
do_replace net/ipv4/netfilter/arp_tables.c:977 [inline]
do_arpt_set_ctl+0x310/0x640 net/ipv4/netfilter/arp_tables.c:1456
Fixes: add6746124 ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+d7358a458d8a81aee898@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4acb0200ab upstream.
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2548288b4f upstream.
It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes. In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC. This unexpected
side effect has caused some UVC cameras to stop working.
In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0. Warning
about such things seems like a bad idea.
This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors. Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.
We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.
Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com>
Fixes: d482c7bb05 ("USB: Skip endpoints with 0 maxpacket length")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18a1b06e5b upstream.
The open method of hiddev handler fails to bring the device out of
autosuspend state as was promised in 0361a28d3f, as it actually has 2
blocks that try to start the transport (call hid_hw_open()) with both
being guarded by the "open" counter, so the 2nd block is never executed as
the first block increments the counter so it is never at 0 when we check
it for the second block.
Additionally hiddev_open() was leaving counter incremented on errors,
causing the device to never be reopened properly if there was ever an
error.
Let's fix all of this by factoring out code that creates client structure
and powers up the device into a separate function that is being called
from usbhid_open() with the "existancelock" being held.
Fixes: 0361a28d3f ("HID: autosuspend support for USB HID")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
