commit 780a7654ce upstream.
audit rule additions containing "-F auid!=4294967295" were failing
with EINVAL because of a regression caused by e1760bd.
Apparently some userland audit rule sets want to know if loginuid uid
has been set and are using a test for auid != 4294967295 to determine
that.
In practice that is a horrible way to ask if a value has been set,
because it relies on subtle implementation details and will break
every time the uid implementation in the kernel changes.
So add a clean way to test if the audit loginuid has been set, and
silently convert the old idiom to the cleaner and more comprehensible
new idiom.
RGB notes: In upstream, audit_rule_to_entry has been refactored out.
This is patch is already upstream in functionally the same form in
commit 780a7654ce . The decimal constant
was cast to unsigned to quiet GCC 4.6 32-bit architecture warnings.
Reported-By: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Tested-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Backported-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6880b0150a upstream.
People/distros vary how they prefix the toolchain name for 64bit builds.
Rather than enforce one convention over another, add a for loop which
does a search for all the general prefixes.
For 64bit builds, we now search for (in order):
hppa64-unknown-linux-gnu
hppa64-linux-gnu
hppa64-linux
For 32bit builds, we look for:
hppa-unknown-linux-gnu
hppa-linux-gnu
hppa-linux
hppa2.0-unknown-linux-gnu
hppa2.0-linux-gnu
hppa2.0-linux
hppa1.1-unknown-linux-gnu
hppa1.1-linux-gnu
hppa1.1-linux
This patch was initiated by Mike Frysinger, with feedback from Jeroen
Roovers, John David Anglin and Helge Deller.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeroen Roovers <jer@gentoo.org>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93782eba49 upstream.
The ifeq operator does not accept globs, so this little bit of code will
never match (unless uname literally prints out "parsic*"). Rewrite to
use a pattern matching operator so that NATIVE is set to 1 on parisc.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbbfde7820 upstream.
The "b" branch instruction used in the fork_like macro only can handle
17-bit pc-relative offsets.
This fails with an out of range offset with some .config files.
Rewrite to use the "be" instruction which
can branch to any address in a space.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0a18819e2 upstream.
Currently, race conditions exist in the handling of TLB interruptions in
entry.S. In particular, dirty bit updates can be lost if an accessed
interruption occurs just after the dirty bit interruption on a different
cpu. Lost dirty bit updates result in user pages not being flushed and
general system instability. This change adds lock and unlock macros to
synchronize all PTE and TLB updates done in entry.S. As a result,
userspace stability is significantly improved.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c207a76bf1 upstream.
Helge and I have found that we have a kernel stack overflow problem
which causes a variety of random failures.
Currently, we re-enable interrupts when returning from an external
interrupt incase we need to schedule or delivery
signals. As a result, a potentially unlimited number of interrupts
can occur while we are running on the kernel
stack. It is very limited in space (currently, 16k). This change
defers enabling interrupts until we have
actually decided to schedule or delivery signals. This only occurs
when we about to return to userspace. This
limits the number of interrupts on the kernel stack to one. In other
cases, interrupts remain disabled until the
final return from interrupt (rfi).
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 264b83c07a upstream.
argv_split(empty_or_all_spaces) happily succeeds, it simply returns
argc == 0 and argv[0] == NULL. Change call_usermodehelper_exec() to
check sub_info->path != NULL to avoid the crash.
This is the minimal fix, todo:
- perhaps we should change argv_split() to return NULL or change the
callers.
- kill or justify ->path[0] check
- narrow the scope of helper_lock()
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9ced8e040 upstream.
When UMS was deprecated it removed support for nomodeset commandline
we really want this in distro land so we can debug stuff, everyone
should fallback to vesa correctly.
v2: oops -1 isn't used anymore, restore original behaviour
-1 is default, so we can boot with nomodeset on the command line,
then use radeon.modeset=1 to override it for debugging later.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fefaedcfb8 upstream.
The "boxes" parameter points into userspace memory. It should be verified
like any other operation against user memory.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6368087e85 upstream.
When a 32 bit version of ipmitool is used on a 64 bit kernel, the
ipmi_devintf code fails to correctly acquire ipmi_mutex. This results in
incomplete data being retrieved in some cases, or other possible failures.
Add a wrapper around compat_ipmi_ioctl() to take ipmi_mutex to fix this.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2bdbee0d9 upstream.
This patch fixes a regression bug introduced in v3.9-rc1 where if the
underlying struct block_device for a IBLOCK backend is configured with
WCE=1 + DPOFUA=1 settings, the rw = WRITE assignment no longer occurs
in iblock_execute_rw(), and rw = 0 is passed to iblock_submit_bios()
in effect causing a READ bio operation to occur.
The offending commit is:
commit d0c8b259f8
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Tue Jan 29 22:10:06 2013 -0800
target/iblock: Use backend REQ_FLUSH hint for WriteCacheEnabled status
Note the WCE=1 + DPOFUA=0, WCE=0 + DPOFUA=1, and WCE=0 + DPOFUA=0 cases
are not affected by this regression bug.
Reported-by: Chris Boot <bootc@bootc.net>
Tested-by: Chris Boot <bootc@bootc.net>
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccf5ae83a6 upstream.
It is possible for one thread to to take se_sess->sess_cmd_lock in
core_tmr_abort_task() before taking a reference count on
se_cmd->cmd_kref, while another thread in target_put_sess_cmd() drops
se_cmd->cmd_kref before taking se_sess->sess_cmd_lock.
This introduces kref_put_spinlock_irqsave() and uses it in
target_put_sess_cmd() to close the race window.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3eccfdb01d upstream.
Fix two issues in OOO commands processing done at iscsit_attach_ooo_cmdsn.
Handle command serial numbers wrap around by using iscsi_sna_lt and not regular comparisson.
The routine iterates until it finds an entry whose serial number is greater than the serial number of
the new one, thus the new entry should be inserted before that entry and not after.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca182aee38 upstream.
The ffmpeg benchmark in the phoronix test suite has threads on
multiple cores that rely on the progress on of threads on other cores
and ping pong back and forth fast enough to make the core appear less
busy than it "should" be. If the core has been at minimum p-state for
a while bump the pstate up to kick the core to see if it is in this
ping pong state. If the core is truly idle the p-state will be
reduced at the next sample time. If the core makes more progress it
will send more work to the thread bringing both threads out of the
ping pong scenario and the p-state will be selected normally.
This fixes a performance regression of approximately 30%
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f469e9cf upstream.
There are two ways that the maximum p-state can be clamped, via a
policy change and via the sysfs file.
The acpi-thermal driver adjusts the p-state policy in response to
thermal events. These changes override the users settings at the
moment.
Use the lowest of the two requested values this ensures that we will
not exceed the requested pstate from either mechanism.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1abc4b20b8 upstream.
Idle time is taken into account in the APERF/MPERF ratio calculation
there is no reason for the driver to track it seperately. This
reduces the work in the driver and makes the code more readable.
Removal of the tracking of sample duration removes the possibility of
the divide by zero exception when the duration is sub 1us
References: https://bugzilla.kernel.org/show_bug.cgi?id=56691
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0885846188 upstream.
The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.
This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22ee3b57c3 upstream.
If gcc (e.g. 4.1.2) decides not to inline vsock_init_tables(), this will
cause a section mismatch:
WARNING: net/vmw_vsock/vsock.o(.text+0x1bc): Section mismatch in reference from the function __vsock_core_init() to the function .init.text:vsock_init_tables()
The function __vsock_core_init() references
the function __init vsock_init_tables().
This is often because __vsock_core_init lacks a __init
annotation or the annotation of vsock_init_tables is wrong.
This may cause crashes if VSOCKETS=y and VMWARE_VMCI_VSOCKETS=m.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c689e63a8 upstream.
With an automatic after split-brain recovery policy of
"after-sb-1pri call-pri-lost-after-sb",
when trying to drbd_set_role() to R_SECONDARY,
we run into a deadlock.
This was first recognized and supposedly fixed by
2009-06-10 "Fixed a deadlock when using automatic split brain recovery when both nodes are"
replacing drbd_set_role() with drbd_change_state() in that code-path,
but the first hunk of that patch forgets to remove the drbd_set_role().
We apparently only ever tested the "two primaries" case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60403f7a4d upstream.
A race condition exists when registering the first watchdog device.
Sequence of events:
- watchdog_register_device calls watchdog_dev_register
- watchdog_dev_register creates the watchdog misc device by calling
misc_register.
At that time, the matching character device (/dev/watchdog0) does not yet
exist, and old_wdd is not set either.
- Userspace gets an event and opens /dev/watchdog
- watchdog_open is called and sets wdd = old_wdd, which is still NULL,
and tries to dereference it. This causes the kernel to panic.
Seen with systemd trying to open /dev/watchdog immediately after
it was created.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c1ef59168 upstream.
pdc_desc_get() is called from pd_prep_slave_sg, and the function is
called from interrupt context(e.g. Uart driver "pch_uart.c").
In fact, I saw kernel error message.
So, GFP_ATOMIC must be used not GFP_NOIO.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f77d602124 ]
We have seen multiple NULL dereferences in __inet6_lookup_established()
After analysis, I found that inet6_sk() could be NULL while the
check for sk_family == AF_INET6 was true.
Bug was added in linux-2.6.29 when RCU lookups were introduced in UDP
and TCP stacks.
Once an IPv6 socket, using SLAB_DESTROY_BY_RCU is inserted in a hash
table, we no longer can clear pinet6 field.
This patch extends logic used in commit fcbdf09d96
("net: fix nulls list corruptions in sk_prot_alloc")
TCP/UDP/UDPLite IPv6 protocols provide their own .clear_sk() method
to make sure we do not clear pinet6 field.
At socket clone phase, we do not really care, as cloning the parent (non
NULL) pinet6 is not adding a fatal race.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 233c7df082 ]
Currently, if macvlan in passthru mode is created and data are rxed and
you remove this device, following panic happens:
NULL pointer dereference at 0000000000000198
IP: [<ffffffffa0196058>] macvlan_handle_frame+0x153/0x1f7 [macvlan]
I'm using following script to trigger this:
<script>
while [ 1 ]
do
ip link add link e1 name macvtap0 type macvtap mode passthru
ip link set e1 up
ip link set macvtap0 up
IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
cat /dev/tap$IFINDEX >/dev/null &
ip link del dev macvtap0
done
</script>
I run this script while "ping -f" is running on another machine to send
packets to e1 rx.
Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.
I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.
Introduced by: commit eb06acdc85 "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b264a1676 ]
The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address. Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c81400be71 ]
When unloading the driver that drives an EISA board, a message similar to the
following one is displayed:
Trying to free nonexistent resource <0000000000013000-000000000001301f>
Then an user is unable to reload the driver because the resource it requested in
the previous load hasn't been freed. This happens most probably due to a typo in
vortex_eisa_remove() which calls release_region() with 'dev->base_addr' instead
of 'edev->base_addr'...
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77d21f23a1 ]
Programs using virtio headers outside of kernel will no longer
build because u16 type does not exist in userspace. All user ABI
must use __u16 typedef instead.
Bug introduce by:
commit 986a4f4d45
Author: Jason Wang <jasowang@redhat.com>
Date: Fri Dec 7 07:04:56 2012 +0000
virtio_net: multiqueue support
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8da3056c04 ]
Jakub reported that it is fairly easy to trigger the BUG() macro
from user space with TPACKET_V3's RX_RING by just giving a wrong
header status flag. We already had a similar situation in commit
7f5c3e3a80 (``af_packet: remove BUG statement in
tpacket_destruct_skb'') where this was the case in the TX_RING
side that could be triggered from user space. So really, don't use
BUG() or BUG_ON() unless there's really no way out, and i.e.
don't use it for consistency checking when there's user space
involved, no excuses, especially not if you're slapping the user
with WARN + dump_stack + BUG all at once. The two functions are
of concern:
prb_retire_current_block() [when block status != TP_STATUS_KERNEL]
prb_open_block() [when block_status != TP_STATUS_KERNEL]
Calls to prb_open_block() are guarded by ealier checks if block_status
is really TP_STATUS_KERNEL (racy!), but the first one BUG() is easily
triggable from user space. System behaves still stable after they are
removed. Also remove that yoda condition entirely, since it's already
guarded.
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5060cec6b ]
There is bug in the receive path of the asix driver at the time a
packet is received larger than MTU size and DF bit set:
BUG: unable to handle kernel paging request at 0000004000000001
IP: [<ffffffff8126f65b>] skb_release_head_state+0x2d/0xd2
...
Call Trace:
<IRQ>
[<ffffffff8126f86d>] ? skb_release_all+0x9/0x1e
[<ffffffff8126f8ad>] ? __kfree_skb+0x9/0x6f
[<ffffffffa00b4200>] ? asix_rx_fixup_internal+0xff/0x1ae [asix]
[<ffffffffa00fb3dc>] ? usbnet_bh+0x4f/0x226 [usbnet]
...
It is easily reproducable by setting an MTU of 512 e. g. and sending
something like
ping -s 1472 -c 1 -M do $SELF
from another box.
And this is because the rx->ax_skb is freed on error, but rx->ax_skb
is not reset, and the size is not reset to zero in this case.
And since the skb is added again to the usbnet->done skb queue it is
accessing already freed memory, resulting in the BUG when freeing a
2nd time. I therefore think the value 0x0000004000000001 show in the
trace is more or less random data.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83401eb499 ]
A bridge should only send topology change notice if it is not
the root bridge. It is possible for message age timer to elect itself
as a new root bridge, and still have a topology change timer running
but waiting for bridge lock on other CPU.
Solve the race by checking if we are root bridge before continuing.
This was the root cause of the cases where br_send_tcn_bpdu would OOPS.
Reported-by: JerryKang <jerry.kang@samsung.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0dcffd0964 ]
Deal with changes in newer xtables while maintaining backward
compatibility. Thanks to Jan Engelhardt for suggestions.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b54912f9c ]
The venerable 3c509 driver only sets its device parent in one case, the ISAPnP one.
It does this with the SET_NETDEV_DEV function. It should register with the device
hierarchy in two additional cases: standard (non-PnP) ISA and EISA.
- Currently they appear here:
/sys/devices/virtual/net/eth0 (standard ISA)
/sys/devices/virtual/net/eth1 (EISA)
- Rather, they should instead be here:
/sys/devices/isa/3c509.0/net/eth0 (standard ISA)
/sys/devices/pci0000:00/0000:00:07.0/00:04/net/eth1 (EISA)
Tested on ISA and EISA boards.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd75eff64d ]
Linux immediately returns SYNACK on (spurious) SYN retransmits, but
keeps the SYNACK timer running independently. Thus the timer may
fire right after the SYNACK retransmit and causes a SYN-SYNACK
cross-fire burst.
Adopt the fast retransmit/recovery idea in established state by
re-arming the SYNACK timer after the fast (SYNACK) retransmit. The
timer may fire late up to 500ms due to the current SYNACK timer wheel,
but it's OK to be conservative when network is congested. Eric's new
listener design should address this issue.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c1bbbffa0 ]
Change MAC802154_CHAN_NONE from ~(u8)0 to 0xff, or the comparison in
mac802154_wpan_xmit() for ``chan == MAC802154_CHAN_NONE'' will not
succeed.
This bug can be boiled down to ``u8 foo = 0xff; if (foo == ~(u8)0)
[...] else [...]'' where the condition will always take the else
branch.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89cc80a44b ]
efx_mcdi_get_board_cfg() uses a buffer for the firmware response that
is only large enough to hold subtypes for the originally defined set
of NVRAM partitions. Longer responses are truncated, and we may read
off the end of the buffer when copying out subtypes for additional
partitions. In particular, this can result in the MTD partition for
an FPGA bitfile being named e.g. 'eth5 sfc_fpga:00' when it should be
'eth5 sfc_fpga:01'. This means the firmware update tool (sfupdate)
can't tell which bitfile should be written to the partition.
Correct the response buffer size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a359f0b21 upstream.
In
commit 9e8944ab56
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Nov 15 11:32:17 2012 +0000
drm: Introduce an iterator over holes in the drm_mm range manager
helpers and iterators for hole handling have been introduced with some
debug BUG_ONs sprinkled over. Unfortunately this broke the mm dumper
which unconditionally tried to compute the size of the very first
hole.
While at it unify the code a bit with the hole dumping in the loop.
v2: Extract a hole dump helper.
Reported-by: Christopher Harvey <charvey@matrox.com>
Cc: Christopher Harvey <charvey@matrox.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f1d036648 upstream.
Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb70a66908 upstream.
The original line,
WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd9c46408f upstream.
Jake reported that since commit 1672c0e319
"mac80211: start auth/assoc timeout on frame status", he is unable to
connect to his AP, which is configured to use passive channel.
After switch to passive channel 4965 firmware drops any TX packet until
it receives beacon. Before commit 1672c0e3 we waited on channel and
retransmit packet after 200ms, that makes we receive beacon on the
meantime and association process succeed. New mac80211 behaviour cause
that any ASSOC frame fail immediately on iwl4965 and we can not
associate.
This patch restore old mac80211 behaviour for iwl4965, by removing
IEEE80211_HW_REPORTS_TX_ACK_STATUS feature. This feature will be
added again to iwl4965 driver, when different, more complex
workaround for this firmware issue, will be added to the driver.
Bisected-by: Jake Edge <jake@lwn.net>
Reported-and-tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73b82bf0bf upstream.
Add handling of rx descriptor underflow. This fixes a fault that could
happen on slow machines, where data is received faster than the CPU can
handle. In such a case the device will use up all rx descriptors and
refuse to send any more data before confirming that it is ok. This
patch enables necessary interrupt to discover such a situation and will
handle them by dropping everything in the ring buffer.
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c539914dcd upstream.
The Tilera hypervisor shipped in releases up through MDE 4.1 launches
the client operating system (i.e. Linux) at privilege level 1 (PL1).
Starting with MDE 4.2, as part of the work to enable KVM, the
Tilera hypervisor launches Linux at PL2 instead.
This commit makes the KERNEL_PL option default to 2 for tilegx, while
still saying at 1 for tilepro, which doesn't have an updated hypervisor.
It also explains how and when you might want to choose another value.
In addition, we change a small buglet in the on-chip Ethernet driver,
where we were failing to use the KERNEL_PL constant in an API call.
To make the transition cleaner, this change also provides the updated
hv_init() API for the new hypervisor that supports announcing Linux's
compiled-in PL, so the hypervisor can generate a suitable error in the
case of a mismatched hypervisor and Linux binary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccd384b104 upstream.
A small bug in this code was causing the ALLMULTI filter to be set
when in fact we were just wanting to program a selective multicast list
to the hardware.
Fix that bug and remove a redundant if condition in the code that
follows.
This fixes wakeup behaviour when multicast WOL is enabled. Previously,
all multicast packets would wake up the system. Now, only those that the
host intended to receive trigger wakeups.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16fdc9d2d upstream.
After unregister_netdevice() call the request is queued and
reg_state is changed to NETREG_UNREGISTERING.
As we check for NETREG_UNREGISTERED state, free_netdev() never
gets executed causing memory leak.
Initialize "dev->destructor" to free_netdev() to free device
data after unregistration.
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48795424ac upstream.
When the XO-4 with 8787 wireless is woken up due to wake-on-WLAN
mwifiex is often flooded with "not allowed while suspended" messages
and the interface is unusable.
[ 202.171609] int: sdio_ireg = 0x1
[ 202.180700] info: mwifiex_process_hs_config: auto cancelling host
sleep since there is interrupt from the firmware
[ 202.201880] event: wakeup device...
[ 202.211452] event: hs_deactivated
[ 202.514638] info: --- Rx: Data packet ---
[ 202.514753] data: 4294957544 BSS(0-0): Data <= kernel
[ 202.514825] PREP_CMD: device in suspended state
[ 202.514839] data: dequeuing the packet ec7248c0 ec4869c0
[ 202.514886] mwifiex_write_data_sync: not allowed while suspended
[ 202.514886] host_to_card, write iomem (1) failed: -1
[ 202.514917] mwifiex_write_data_sync: not allowed while suspended
[ 202.514936] host_to_card, write iomem (2) failed: -1
[ 202.514949] mwifiex_write_data_sync: not allowed while suspended
[ 202.514965] host_to_card, write iomem (3) failed: -1
[ 202.514976] mwifiex_write_data_async failed: 0xFFFFFFFF
This can be readily reproduced when putting the XO-4 in a loop where
it goes to sleep due to inactivity, but then wakes up due to an
incoming ping. The error is hit within an hour or two.
This issue happens when an interrupt comes in early while host sleep
is still activated. Driver handles this case by auto cancelling host
sleep. However is_suspended flag is still set which prevents any cmd
or data from being sent to firmware. Fix it by clearing is_suspended
flag in this path.
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ef69d0394 upstream.
If no keycache slots are available, ath_key_config can return -ENOSPC.
If the key index is not checked for errors, it can lead to logspam that
looks like this: "ath: wiphy0: keyreset: keycache entry 228 out of range"
This can cause follow-up errors if the invalid keycache index gets
used for tx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79c66ce8f6 upstream.
commit b3f271e86e (powerpc: POWER7 optimised memcpy using VMX and
enhanced prefetch) uses VMX when it is safe to do so (ie not in
interrupt). It also looks at the task struct to decide if we have to
save the current tasks' VMX state.
kexec calls memcpy() at a point where the task struct may have been
overwritten by the new kexec segments. If it has been overwritten
then when memcpy -> enable_altivec looks up current->thread.regs->msr
we get a cryptic oops or lockup.
I also notice we aren't initialising thread_info->cpu, which means
smp_processor_id is broken. Fix that too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 120496ac2d upstream.
This patch brings online all threads which are present but not online
prior to migration/hibernation. After migration/hibernation those
threads are taken back offline.
During migration/hibernation all online CPUs must call H_JOIN, this is
required by the hypervisor. Without this patch, threads that are offline
(H_CEDE'd) will not be woken to make the H_JOIN call and the OS will be
deadlocked (all threads either JOIN'd or CEDE'd).
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6eabb3301b upstream.
The implementation of cmpxchg64() for the ARM v6 and v7 architecture
casts parameter 2 and 3 (the old and new 64bit values) to an unsigned
long before calling the atomic_cmpxchg64() function. This clears
the top 32 bits of the old and new values, resulting in the wrong
values being compare-exchanged. Luckily, this only appears to be used
for 64-bit sched_clock, which we don't (yet) have on ARM.
This bug was introduced by commit 3e0f5a15f5 ("ARM: 7404/1: cmpxchg64:
use atomic64 and local64 routines for cmpxchg64").
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 074d72ff57 upstream.
This can easily be triggered if a new CPU is added (via
ACPI hotplug mechanism) and from user-space you do:
echo 1 > /sys/devices/system/cpu/cpu3/online
(or wait for UDEV to do it) on a newly appeared physical CPU.
The deadlock is that the "store_online" in drivers/base/cpu.c
takes the cpu_hotplug_driver_lock() lock, then calls "cpu_up".
"cpu_up" eventually ends up calling "save_mc_for_early"
which also takes the cpu_hotplug_driver_lock() lock.
And here is that lockdep thinks of it:
smpboot: Stack at about ffff880075c39f44
smpboot: CPU3: has booted.
microcode: CPU3 sig=0x206a7, pf=0x2, revision=0x25
=============================================
[ INFO: possible recursive locking detected ]
3.9.0upstream-10129-g167af0e #1 Not tainted
---------------------------------------------
sh/2487 is trying to acquire lock:
(x86_cpu_hotplug_driver_mutex){+.+.+.}, at: [<ffffffff81075512>] cpu_hotplug_driver_lock+0x12/0x20
but task is already holding lock:
(x86_cpu_hotplug_driver_mutex){+.+.+.}, at: [<ffffffff81075512>] cpu_hotplug_driver_lock+0x12/0x20
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(x86_cpu_hotplug_driver_mutex);
lock(x86_cpu_hotplug_driver_mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
6 locks held by sh/2487:
#0: (sb_writers#5){.+.+.+}, at: [<ffffffff811ca48d>] vfs_write+0x17d/0x190
#1: (&buffer->mutex){+.+.+.}, at: [<ffffffff812464ef>] sysfs_write_file+0x3f/0x160
#2: (s_active#20){.+.+.+}, at: [<ffffffff81246578>] sysfs_write_file+0xc8/0x160
#3: (x86_cpu_hotplug_driver_mutex){+.+.+.}, at: [<ffffffff81075512>] cpu_hotplug_driver_lock+0x12/0x20
#4: (cpu_add_remove_lock){+.+.+.}, at: [<ffffffff810961c2>] cpu_maps_update_begin+0x12/0x20
#5: (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff810962a7>] cpu_hotplug_begin+0x27/0x60
Suggested-and-Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: fenghua.yu@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1368029583-23337-1-git-send-email-konrad.wilk@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6155736ad upstream.
In the case where we are allocating for a non-extent file,
we must limit the groups we allocate from to those below
2^32 blocks, and ext4_mb_regular_allocator() attempts to
do this initially by putting a cap on ngroups for the
subsequent search loop.
However, the initial target group comes in from the
allocation context (ac), and it may already be beyond
the artificially limited ngroups. In this case,
the limit
if (group == ngroups)
group = 0;
at the top of the loop is never true, and the loop will
run away.
Catch this case inside the loop and reset the search to
start at group 0.
[sandeen@redhat.com: add commit msg & comments]
Signed-off-by: Lachlan McIlroy <lmcilroy@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60705c8946 upstream.
Special preds are created when folding a series of preds that
can be done in serial. These are allocated in an ops field of
the pred structure. But they were never freed, causing memory
leaks.
This was discovered using the kmemleak checker:
unreferenced object 0xffff8800797fd5e0 (size 32):
comm "swapper/0", pid 1, jiffies 4294690605 (age 104.608s)
hex dump (first 32 bytes):
00 00 01 00 03 00 05 00 07 00 09 00 0b 00 0d 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff814b52af>] kmemleak_alloc+0x73/0x98
[<ffffffff8111ff84>] kmemleak_alloc_recursive.constprop.42+0x16/0x18
[<ffffffff81120e68>] __kmalloc+0xd7/0x125
[<ffffffff810d47eb>] kcalloc.constprop.24+0x2d/0x2f
[<ffffffff810d4896>] fold_pred_tree_cb+0xa9/0xf4
[<ffffffff810d3781>] walk_pred_tree+0x47/0xcc
[<ffffffff810d5030>] replace_preds.isra.20+0x6f8/0x72f
[<ffffffff810d50b5>] create_filter+0x4e/0x8b
[<ffffffff81b1c30d>] ftrace_test_event_filter+0x5a/0x155
[<ffffffff8100028d>] do_one_initcall+0xa0/0x137
[<ffffffff81afbedf>] kernel_init_freeable+0x14d/0x1dc
[<ffffffff814b24b7>] kernel_init+0xe/0xdb
[<ffffffff814d539c>] ret_from_fork+0x7c/0xb0
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b0c0f294f upstream.
Prarit reported a crash on CPU offline/online. The reason is that on
CPU down the NOHZ related per cpu data of the dead cpu is not cleaned
up. If at cpu online an interrupt happens before the per cpu tick
device is registered the irq_enter() check potentially sees stale data
and dereferences a NULL pointer.
Cleanup the data after the cpu is dead.
Reported-by: Prarit Bhargava <prarit@redhat.com>
Cc: Mike Galbraith <bitbucket@online.de>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1305031451561.2886@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42a5cf46cd upstream.
An inactive timer's base can refer to a offline cpu's base.
In the current code, cpu_base's lock is blindly reinitialized each
time a CPU is brought up. If a CPU is brought online during the period
that another thread is trying to modify an inactive timer on that CPU
with holding its timer base lock, then the lock will be reinitialized
under its feet. This leads to following SPIN_BUG().
<0> BUG: spinlock already unlocked on CPU#3, kworker/u:3/1466
<0> lock: 0xe3ebe000, .magic: dead4ead, .owner: kworker/u:3/1466, .owner_cpu: 1
<4> [<c0013dc4>] (unwind_backtrace+0x0/0x11c) from [<c026e794>] (do_raw_spin_unlock+0x40/0xcc)
<4> [<c026e794>] (do_raw_spin_unlock+0x40/0xcc) from [<c076c160>] (_raw_spin_unlock+0x8/0x30)
<4> [<c076c160>] (_raw_spin_unlock+0x8/0x30) from [<c009b858>] (mod_timer+0x294/0x310)
<4> [<c009b858>] (mod_timer+0x294/0x310) from [<c00a5e04>] (queue_delayed_work_on+0x104/0x120)
<4> [<c00a5e04>] (queue_delayed_work_on+0x104/0x120) from [<c04eae00>] (sdhci_msm_bus_voting+0x88/0x9c)
<4> [<c04eae00>] (sdhci_msm_bus_voting+0x88/0x9c) from [<c04d8780>] (sdhci_disable+0x40/0x48)
<4> [<c04d8780>] (sdhci_disable+0x40/0x48) from [<c04bf300>] (mmc_release_host+0x4c/0xb0)
<4> [<c04bf300>] (mmc_release_host+0x4c/0xb0) from [<c04c7aac>] (mmc_sd_detect+0x90/0xfc)
<4> [<c04c7aac>] (mmc_sd_detect+0x90/0xfc) from [<c04c2504>] (mmc_rescan+0x7c/0x2c4)
<4> [<c04c2504>] (mmc_rescan+0x7c/0x2c4) from [<c00a6a7c>] (process_one_work+0x27c/0x484)
<4> [<c00a6a7c>] (process_one_work+0x27c/0x484) from [<c00a6e94>] (worker_thread+0x210/0x3b0)
<4> [<c00a6e94>] (worker_thread+0x210/0x3b0) from [<c00aad9c>] (kthread+0x80/0x8c)
<4> [<c00aad9c>] (kthread+0x80/0x8c) from [<c000ea80>] (kernel_thread_exit+0x0/0x8)
As an example, this particular crash occurred when CPU #3 is executing
mod_timer() on an inactive timer whose base is refered to offlined CPU
#2. The code locked the timer_base corresponding to CPU #2. Before it
could proceed, CPU #2 came online and reinitialized the spinlock
corresponding to its base. Thus now CPU #3 held a lock which was
reinitialized. When CPU #3 finally ended up unlocking the old cpu_base
corresponding to CPU #2, we hit the above SPIN_BUG().
CPU #0 CPU #3 CPU #2
------ ------- -------
..... ...... <Offline>
mod_timer()
lock_timer_base
spin_lock_irqsave(&base->lock)
cpu_up(2) ..... ......
init_timers_cpu()
.... ..... spin_lock_init(&base->lock)
..... spin_unlock_irqrestore(&base->lock) ......
<spin_bug>
Allocation of per_cpu timer vector bases is done only once under
"tvec_base_done[]" check. In the current code, spinlock_initialization
of base->lock isn't under this check. When a CPU is up each time the
base lock is reinitialized. Move base spinlock initialization under
the check.
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Link: http://lkml.kernel.org/r/1368520142-4136-1-git-send-email-tirupath@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4f711ee03 upstream.
Kay Sievers noted that the ALWAYS_USE_PERSISTENT_CLOCK config,
which enables some minor compile time optimization to avoid
uncessary code in mostly the suspend/resume path could cause
problems for userland.
In particular, the dependency for RTC_HCTOSYS on
!ALWAYS_USE_PERSISTENT_CLOCK, which avoids setting the time
twice and simplifies suspend/resume, has the side effect
of causing the /sys/class/rtc/rtcN/hctosys flag to always be
zero, and this flag is commonly used by udev to setup the
/dev/rtc symlink to /dev/rtcN, which can cause pain for
older applications.
While the udev rules could use some work to be less fragile,
breaking userland should strongly be avoided. Additionally
the compile time optimizations are fairly minor, and the code
being optimized is likely to be reworked in the future, so
lets revert this change.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Link: http://lkml.kernel.org/r/1366828376-18124-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33e2208acf upstream.
Jiri reported a regression in auditing of open(..., O_CREAT) syscalls.
In older kernels, creating a file with open(..., O_CREAT) created
audit_name records that looked like this:
type=PATH msg=audit(1360255720.628:64): item=1 name="/abc/foo" inode=138810 dev=fd:00 mode=0100640 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
type=PATH msg=audit(1360255720.628:64): item=0 name="/abc/" inode=138635 dev=fd:00 mode=040750 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
...in recent kernels though, they look like this:
type=PATH msg=audit(1360255402.886:12574): item=2 name=(null) inode=264599 dev=fd:00 mode=0100640 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
type=PATH msg=audit(1360255402.886:12574): item=1 name=(null) inode=264598 dev=fd:00 mode=040750 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
type=PATH msg=audit(1360255402.886:12574): item=0 name="/abc/foo" inode=264598 dev=fd:00 mode=040750 ouid=0 ogid=0 rdev=00:00 obj=unconfined_u:object_r:default_t:s0
Richard bisected to determine that the problems started with commit
bfcec708, but the log messages have changed with some later
audit-related patches.
The problem is that this audit_inode call is passing in the parent of
the dentry being opened, but audit_inode is being called with the parent
flag false. This causes later audit_inode and audit_inode_child calls to
match the wrong entry in the audit_names list.
This patch simply sets the flag to properly indicate that this inode
represents the parent. With this, the audit_names entries are back to
looking like they did before.
Reported-by: Jiri Jaburek <jjaburek@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Test By: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdee3904b4 upstream.
Commit b05d8447e7 (audit: inline audit_syscall_entry to reduce
burden on archs) changed audit_syscall_entry to check for a dummy
context before calling __audit_syscall_entry. Unfortunately the dummy
context state is maintained in __audit_syscall_entry so once set it
never gets cleared, even if the audit rules change.
As a result, if there are no auditing rules when a process starts
then it will never be subject to any rules added later. x86 doesn't
see this because it has an assembly fast path that calls directly into
__audit_syscall_entry.
I noticed this issue when working on audit performance optimisations.
I wrote a set of simple test cases available at:
http://ozlabs.org/~anton/junkcode/audit_tests.tar.gz
02_new_rule.py fails without the patch and passes with it. The
test case clears all rules, starts a process, adds a rule then
verifies the process produces a syscall audit record.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39c60a0948 upstream.
Some arrays synchronize their full non volatile cache when the sd driver sends
a SYNCHRONIZE CACHE command. Unfortunately, they can have Terrabytes of this
and we send a SYNCHRONIZE CACHE for every barrier if an array reports it has a
writeback cache. This leads to massive slowdowns on journalled filesystems.
The fix is to allow userspace to turn off the writeback cache setting as a
temporary measure (i.e. without doing the MODE SELECT to write it back to the
device), so even though the device reported it has a writeback cache, the
user, knowing that the cache is non volatile and all they care about is
filesystem correctness, can turn that bit off in the kernel and avoid the
performance ruinous (and safety irrelevant) SYNCHRONIZE CACHE commands.
The way you do this is add a 'temporary' prefix when performing the usual
cache setting operations, so
echo temporary write through > /sys/class/scsi_disk/<disk>/cache_type
Reported-by: Ric Wheeler <rwheeler@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f1fc268c4 upstream.
If a user did:
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
we would (this a build with DEBUG enabled) get to:
smpboot: ++++++++++++++++++++=_---CPU UP 1
.. snip..
smpboot: Stack at about ffff880074c0ff44
smpboot: CPU1: has booted.
and hang. The RCU mechanism would kick in an try to IPI the CPU1
but the IPIs (and all other interrupts) would never arrive at the
CPU1. At first glance at least. A bit digging in the hypervisor
trace shows that (using xenanalyze):
[vla] d4v1 vec 243 injecting
0.043163027 --|x d4v1 intr_window vec 243 src 5(vector) intr f3
] 0.043163639 --|x d4v1 vmentry cycles 1468
] 0.043164913 --|x d4v1 vmexit exit_reason PENDING_INTERRUPT eip ffffffff81673254
0.043164913 --|x d4v1 inj_virq vec 243 real
[vla] d4v1 vec 243 injecting
0.043164913 --|x d4v1 intr_window vec 243 src 5(vector) intr f3
] 0.043165526 --|x d4v1 vmentry cycles 1472
] 0.043166800 --|x d4v1 vmexit exit_reason PENDING_INTERRUPT eip ffffffff81673254
0.043166800 --|x d4v1 inj_virq vec 243 real
[vla] d4v1 vec 243 injecting
there is a pending event (subsequent debugging shows it is the IPI
from the VCPU0 when smpboot.c on VCPU1 has done
"set_cpu_online(smp_processor_id(), true)") and the guest VCPU1 is
interrupted with the callback IPI (0xf3 aka 243) which ends up calling
__xen_evtchn_do_upcall.
The __xen_evtchn_do_upcall seems to do *something* but not acknowledge
the pending events. And the moment the guest does a 'cli' (that is the
ffffffff81673254 in the log above) the hypervisor is invoked again to
inject the IPI (0xf3) to tell the guest it has pending interrupts.
This repeats itself forever.
The culprit was the per_cpu(xen_vcpu, cpu) pointer. At the bootup
we set each per_cpu(xen_vcpu, cpu) to point to the
shared_info->vcpu_info[vcpu] but later on use the VCPUOP_register_vcpu_info
to register per-CPU structures (xen_vcpu_setup).
This is used to allow events for more than 32 VCPUs and for performance
optimizations reasons.
When the user performs the VCPU hotplug we end up calling the
the xen_vcpu_setup once more. We make the hypercall which returns
-EINVAL as it does not allow multiple registration calls (and
already has re-assigned where the events are being set). We pick
the fallback case and set per_cpu(xen_vcpu, cpu) to point to the
shared_info->vcpu_info[vcpu] (which is a good fallback during bootup).
However the hypervisor is still setting events in the register
per-cpu structure (per_cpu(xen_vcpu_info, cpu)).
As such when the events are set by the hypervisor (such as timer one),
and when we iterate in __xen_evtchn_do_upcall we end up reading stale
events from the shared_info->vcpu_info[vcpu] instead of the
per_cpu(xen_vcpu_info, cpu) structures. Hence we never acknowledge the
events that the hypervisor has set and the hypervisor keeps on reminding
us to ack the events which we never do.
The fix is simple. Don't on the second time when xen_vcpu_setup is
called over-write the per_cpu(xen_vcpu, cpu) if it points to
per_cpu(xen_vcpu_info).
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7783819920 upstream.
The error in lis3lv02_poweron() is harmless in the resume path, so
we should ignore it. It is inline with the other usages of lis3lv02_poweron()
and matches the 3.0 code for this routine. This patch is in suse git and
might have missed making it into the mainline.
opensuse - commit id: 66ccdac87c322cf7af12bddba8c805af640b1cff
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f415eb255 upstream.
The Linux client is using CLAIM_FH to implement regular opens, not just
recovery cases, so it depends on the server to check permissions
correctly.
Therefore the owner override, which may make sense in the delegation
recovery case, isn't right in the CLAIM_FH case.
Symptoms: on a client with 49f9a0fafd
"NFSv4.1: Enable open-by-filehandle", Bryan noticed this:
touch test.txt
chmod 000 test.txt
echo test > test.txt
succeeding.
Reported-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9a3c9823a upstream.
Some users have reported that after running a process with
hundreds of threads on intensive CPU-bound loads, the cputime
of the group started to freeze after a few days.
This is due to how we scale the tick-based cputime against
the scheduler precise execution time value.
We add the values of all threads in the group and we multiply
that against the sum of the scheduler exec runtime of the whole
group.
This easily overflows after a few days/weeks of execution.
A proposed solution to solve this was to compute that multiplication
on stime instead of utime:
62188451f0
("cputime: Avoid multiplication overflow on utime scaling")
The rationale behind that was that it's easy for a thread to
spend most of its time in userspace under intensive CPU-bound workload
but it's much harder to do CPU-bound intensive long run in the kernel.
This postulate got defeated when a user recently reported he was still
seeing cputime freezes after the above patch. The workload that
triggers this issue relates to intensive networking workloads where
most of the cputime is consumed in the kernel.
To reduce much more the opportunities for multiplication overflow,
lets reduce the multiplication factors to the remainders of the division
between sched exec runtime and cputime. Assuming the difference between
these shouldn't ever be that large, it could work on many situations.
This gets the same results as in the upstream scaling code except for
a small difference: the upstream code always rounds the results to
the nearest integer not greater to what would be the precise result.
The new code rounds to the nearest integer either greater or not
greater. In practice this difference probably shouldn't matter but
it's worth mentioning.
If this solution appears not to be enough in the end, we'll
need to partly revert back to the behaviour prior to commit
0cf55e1ec0
("sched, cputime: Introduce thread_group_times()")
Back then, the scaling was done on exit() time before adding the cputime
of an exiting thread to the signal struct. And then we'll need to
scale one-by-one the live threads cputime in thread_group_cputime(). The
drawback may be a slightly slower code on exit time.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502624bdad upstream.
This patch uses memalloc_noio_save to avoid a possible deadlock in
dm-bufio. (it could happen only with large block size, at most
PAGE_SIZE << MAX_ORDER (typically 8MiB).
__vmalloc doesn't fully respect gfp flags. The specified gfp flags are
used for allocation of requested pages, structures vmap_area, vmap_block
and vm_struct and the radix tree nodes.
However, the kernel pagetables are allocated always with GFP_KERNEL.
Thus the allocation of pagetables can recurse back to the I/O layer and
cause a deadlock.
This patch uses the function memalloc_noio_save to set per-process
PF_MEMALLOC_NOIO flag and the function memalloc_noio_restore to restore
it. When this flag is set, all allocations in the process are done with
implied GFP_NOIO flag, thus the deadlock can't happen.
This should be backported to stable kernels, but they don't have the
PF_MEMALLOC_NOIO flag and memalloc_noio_save/memalloc_noio_restore
functions. So, PF_MEMALLOC should be set and restored instead.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d793e68427 upstream.
Fix a regression in the calculation of the stripe_width in the
dm stripe target which led to incorrect processing of device limits.
The stripe_width is the stripe device length divided by the number of
stripes. The group of commits in the range f14fa69 ("dm stripe: fix
size test") to eb850de ("dm stripe: support for non power of 2
chunksize") interfered with each other (a merging error) and led to the
stripe_width being set incorrectly to the stripe device length divided by
chunk_size * stripe_count.
For example, a stripe device's table with: 0 33553920 striped 3 512 ...
should result in a stripe_width of 11184640 (33553920 / 3), but due to
the bug it was getting set to 21845 (33553920 / (512 * 3)).
The impact of this bug is that device topologies that previously worked
fine with the stripe target are no longer considered valid. In
particular, there is a higher risk of seeing this issue if one of the
stripe devices has a 4K logical block size. Resulting in an error
message like this:
"device-mapper: table: 253:4: len=21845 not aligned to h/w logical block size 4096 of dm-1"
The fix is to swap the order of the divisions and to use a temporary
variable for the second one, so that width retains the intended
value.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc019b21fb upstream.
If device_not_write_same_capable() returns true then the iterate_devices
loop in dm_table_supports_write_same() should return false.
Reported-by: Bharata B Rao <bharata.rao@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a188eb126 upstream.
In of_dma_controller_register() routine we are calling of_get_property() as an
parameter to be32_to_cpup(). In case the property doesn't exist we will get a
crash.
This patch changes this code to check if we got a valid property first and then
runs be32_to_cpup() on it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Robert Richter <robert.richter@calxeda.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff359b1491 upstream.
The older Conexant codecs have up to two EAPDs and these are supposed
to be rather statically turned on. The new generic parser code
assumes the dynamic on/off per path usage, thus it resulted in the
silent output on some machines.
This patch fixes the problem by simply assuming the static EAPD on for
such old Conexant codecs as we did until 3.8 kernel.
Reported-and-tested-by: Christopher K. <c.krooss@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2195b063f6 upstream.
The interrupt handler azx_interrupt will call azx_update_rirb,
which may call snd_hda_queue_unsol_event, snd_hda_queue_unsol_event
will dereference chip->bus pointer.
The problem is we alloc chip->bus in azx_codec_create
which will be called after we enable IRQ and enable unsolicited
event in azx_probe.
This will cause Oops due dereference NULL pointer. I meet it, good luck:)
[Rearranged the NULL check before the tracepoint and added another
NULL check of bus->workq -- tiwai]
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c35ae3c32 upstream.
This reverts commit affdb62b81.
The commit introduced a regression with AD codecs where the stream is
always clean up. Since the patch is just a minor optimization and
reverting the commit fixes the issue, let's just revert it.
Reported-and-tested-by: Michael Burian <michael.burian@sbg.at>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61388f9e5d upstream.
Can only happen under these conditions: 1) The DSDT version is 1,
meaning integers are 32-bits. 2) The field is between 33 and 64
bits long.
It applies cleanly back to ACPICA 20100806+ (Linux v2.6.37+).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e65f131a14 upstream.
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1e0ac192b upstream.
It looks like the manual merge 0d69a3c731 ("Merge
branches 'for-3.9/sony' and 'for-3.9/steelseries' into for-linus") accidentally
removed Sony RF receiver with USB product id 0x0374 from the "have special
driver" list, effectively nullifying a464918419
("HID: add support for Sony RF receiver with USB product id 0x0374"). Add the
device back to the list.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 326f578f7e upstream.
This is an almost-undocumented instruction available in 32-bit mode.
I say "almost" undocumented because AMD documents it in their opcode
maps just to say that it is unavailable in 64-bit mode (sections
"A.2.1 One-Byte Opcodes" and "B.3 Invalid and Reassigned Instructions
in 64-Bit Mode").
It is roughly equivalent to "sbb %al, %al" except it does not
set the flags. Use fastop to emulate it, but do not use the opcode
directly because it would fail if the host is 64-bit!
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fa57952d7 upstream.
This is used by SGABIOS, KVM breaks with emulate_invalid_guest_state=1.
It is just a MOV in disguise, with a funny source address.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a035d5c64d upstream.
This is used by SGABIOS, KVM breaks with emulate_invalid_guest_state=1.
AAM needs the source operand to be unsigned; do the same in AAD as well
for consistency, even though it does not affect the result.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d76c49e9f upstream.
The invalid guest state emulation loop does not check halt_request
which causes 100% cpu loop while guest is in halt and in invalid
state, but more serious issue is that this leaves halt_request set, so
random instruction emulated by vm86 #GP exit can be interpreted
as halt which causes guest hang. Fix both problems by handling
halt_request in emulation loop.
Reported-by: Tomas Papan <tomas.papan@gmail.com>
Tested-by: Tomas Papan <tomas.papan@gmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12b2f117f3 upstream.
audit_trim_trees() calls get_tree(). If a failure occurs we must call
put_tree().
[akpm@linux-foundation.org: run put_tree() before mutex_lock() for small scalability improvement]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5a2a15f81 upstream.
If a NFS client receives a delegation for a file after it has taken
a lock on that file, we can currently end up in a situation where
we mistakenly skip unlocking that file.
The following patch swaps an erroneous check in nfs4_proc_unlck for
whether or not the file has a delegation to one which checks whether
or not we hold a lock stateid for that file.
Reported-by: Chuck Lever <Chuck.Lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Chuck Lever <Chuck.Lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fdb7846c9 upstream.
A rebranded Novatel E371 for AT&T's LTE bands. qmi_wwan should drive this
device, while cdc_ether should ignore it. Even though the USB descriptors
are plain CDC-ETHER that USB interface is a QMI interface.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e253aaf0af upstream.
Commit 4f535093cf "PCI: Put pci_dev in device tree as early as possible"
moved final fixups from pci_bus_add_device() to pci_device_add(). But
pci_device_add() happens before resource assignment, so BARs may not be
valid yet.
Typical flow for hot-add:
pciehp_configure_device
pci_scan_slot
pci_scan_single_device
pci_device_add
pci_fixup_device(pci_fixup_final, dev) # previous location
# resource assignment happens here
pci_bus_add_devices
pci_bus_add_device
pci_fixup_device(pci_fixup_final, dev) # new location
[bhelgaas: changelog, move fixups to pci_bus_add_device()]
Reference: https://lkml.kernel.org/r/20130415182614.GB9224@xanatos
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Tested-by: David Bulkow <David.Bulkow@stratus.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8c64d165c upstream.
I get the following warning on boot:
------------[ cut here ]------------
WARNING: at drivers/base/core.c:575 device_create_file+0x9a/0xa0()
Hardware name: -[8737R2A]-
Write permission without 'store'
...
</snip>
Drilling down, this is related to dynamic channel ce_count attribute
files sporting a S_IWUSR mode without a ->store() function. Looking
around, it appears that they aren't supposed to have a ->store()
function. So remove the bogus write permission to get rid of the
warning.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
[ shorten commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb384b55ae upstream.
This is the same as the fix from commit
Btrfs: fix bad extent logging
but for O_DIRECT. I missed this when I fixed the problem originally, we were
still using the em for the orig_start and orig_block_len, which would be the
merged extent. We need to use the actual extent from the on disk file extent
item, which we have to lookup to make sure it's ok to nocow anyway so just pass
in some pointers to hold this info. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41b0fc4280 upstream.
A user reported a panic while running a balance. What was happening was he was
relocating a block, which added the reference to the relocation tree. Then
relocation would walk through the relocation tree and drop that reference and
free that block, and then it would walk down a snapshot which referenced the
same block and add another ref to the block. The problem is this was all
happening in the same transaction, so the parent block was free'ed up when we
drop our reference which was immediately available for allocation, and then it
was used _again_ to add a reference for the same block from a different
snapshot. This resulted in something like this in the delayed ref tree
add ref to 90234880, parent=2067398656, ref_root 1766, level 1
del ref to 90234880, parent=2067398656, ref_root 18446744073709551608, level 1
add ref to 90234880, parent=2067398656, ref_root 1767, level 1
as you can see the ref_root's don't match, because when we inc the ref we use
the header owner, which is the original tree the block belonged to, instead of
the data reloc tree. Then when we remove the extent we use the reloc tree
objectid. But none of this matters, since it is a shared reference which means
only the parent matters. When the delayed ref stuff runs it adds all the
increments first, and then does all the drops, to make sure that we don't delete
the ref if we net a positive ref count. But tree blocks aren't allowed to have
multiple refs from the same block, so this panics when it tries to add the
second ref. We need the add and the drop to cancel each other out in memory so
we only do the final add.
So to fix this we need to adjust how the delayed refs are added to the tree.
Only the ref_root matters when it is a normal backref, and only the parent
matters when it is a shared backref. So make our decision based on what ref
type we have. This allows us to keep the ref_root in memory in case anybody
wants to use it for something else, and it allows the delayed refs to be merged
properly so we don't end up with this panic.
With this patch the users image no longer panics on mount, and it has a clean
fsck after a normal mount/umount cycle. Thanks,
Reported-by: Roman Mamedov <rm@romanrm.ru>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fe70b579c upstream.
ftrace_dump() had a lot of issues. What ftrace_dump() does, is when
ftrace_dump_on_oops is set (via a kernel parameter or sysctl), it
will dump out the ftrace buffers to the console when either a oops,
panic, or a sysrq-z occurs.
This was written a long time ago when ftrace was fragile to recursion.
But it wasn't written well even for that.
There's a possible deadlock that can occur if a ftrace_dump() is happening
and an NMI triggers another dump. This is because it grabs a lock
before checking if the dump ran.
It also totally disables ftrace, and tracing for no good reasons.
As the ring_buffer now checks if it is read via a oops or NMI, where
there's a chance that the buffer gets corrupted, it will disable
itself. No need to have ftrace_dump() do the same.
ftrace_dump() is now cleaned up where it uses an atomic counter to
make sure only one dump happens at a time. A simple atomic_inc_return()
is enough that is needed for both other CPUs and NMIs. No need for
a spinlock, as if one CPU is running the dump, no other CPU needs
to do it too.
The tracing_on variable is turned off and not turned on. The original
code did this, but it wasn't pretty. By just disabling this variable
we get the result of not seeing traces that happen between crashes.
For sysrq-z, it doesn't get turned on, but the user can always write
a '1' to the tracing_on file. If they are using sysrq-z, then they should
know about tracing_on.
The new code is much easier to read and less error prone. No more
deadlock possibility when an NMI triggers here.
Reported-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e884fc640c upstream.
Just disabling the mem requests should be enough, but
that doesn't seem to work correctly on efi systems.
v2: blank displays first, then disable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b48b968c0 upstream.
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10257a6d83 upstream.
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bea5497bfc upstream.
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b27290dd upstream.
When ppgtt is enabled, dev_priv->gtt.total has excluded the gtt space
occupied by ppgtt table in i915_gem_init_global_gtt() function. So the
calculation of first_pd_entry_in_global_pt doesn't need to subtract
I915_PPGTT_PD_ENTRIES again. Or else PPGTT directory table will be
destroyed by global gtt allocation.
This regression has been introduced in
commit a54c0c279f
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Thu Jan 24 14:45:00 2013 -0800
drm/i915: remove intel_gtt structure
The breakage is pretty subtile since the old gtt_total_entries
included the pde range, whereas the new on did not.
Signed-off-by: Xiong Zhang<xiong.y.zhang@intel.com>
[danvet: Add regression citation and cc: stable. Thanks to Chris for
correcting my wrong guess about which commit broke things.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c5164d7b upstream.
Yet again our current confusion between doing the modeset globally,
but only having the new parameters for one crtc at a time.
So that intel_set_mode essentially already does a global modeset:
intel_modeset_affected_pipes compares the current state with where we
want to go to (which is carefully set up by intel_crtc_set_config) and
then goes through the modeset sequence for any crtc which needs
updating.
Now the issue is that the actual interface with the remaining code
still only works on one crtc, and so we only pass in one fb and one
mode. In intel_set_mode we also only compute one intel_crtc_config
(which should be the one for the crtc we're doing a modeset on).
The reason for that mismatch is twofold:
- We want to eventually do all modeset as global state changes, so
it's just infrastructure prep.
- But even the old semantics can change more than one crtc when you
e.g. move a connector from crtc A to crtc B, then both crtc A and B
need to be updated. Usually that means one pipe is disabled and the
other enabled. This is also the reason why the hack doesn't touch the
disable_pipes mask.
Now hilarity ensued in our kms config restore paths when we actually
try to do a modeset on all crtcs: If the first crtc should be off and
the second should be on, then the call on the first crtc will notice
that the 2nd one should be switched on and so tries to compute the
pipe_config. But due to a lack of passed-in fb (crtc 1 should be off
after all) it only results in tears.
This case is ridiculously easy to hit on gen2/3 where the lvds output
is restricted to pipe B. Note that before the pipe_config bpp rework
gen2/3 didn't care really about the fb->depth, so this is a regression
brought to light with
commit 4e53c2e010
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
But apparently Ajax also managed to blow up pch platforms, probably
with some randomized configs, and pch platforms trip up over the lack
of an fb even in the old code. So this actually goes back to the first
introduction of the new modeset restore code in
commit 45e2b5f640
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 23 18:16:34 2012 +0100
drm/i915: force restore on lid open
Fix this mess by now by justing shunting all the cool new global
modeset logic in intel_modeset_affected_pipes.
v2: Improve commit message and clean up all the comments in
intel_modeset_affected_pipes - since the introduction of the modeset
restore code they've been a bit outdated.
Bugzill: https://bugzilla.redhat.com/show_bug.cgi?id=917725
References: http://www.mail-archive.com/stable@vger.kernel.org/msg38084.html
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c40c0f5bd5 upstream.
We may have DDI_BUF_CTL(PORT_A) configured with 2 lanes and still not
have CRT, so just check for !IS_ULT. This problem happened on a real
machine and resulted in a very ugly dmesg.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc652f90e0 upstream.
Backlight cleanup in the eDP connector destroy callback caused the
backlight device to be removed on some systems that first initialized LVDS
and then attempted to initialize eDP. Prevent multiple backlight
initializations, and ensure backlight cleanup is only done once by moving
it to modeset cleanup.
A small wrinkle is the introduced asymmetry in backlight
setup/cleanup. This could be solved by adding refcounting, but it seems
overkill considering that there should only ever be one backlight device.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55701
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Peter Verthez <peter.verthez@skynet.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f30da187cd upstream.
It will be only consistent once we've restored all the crtcs. Since a
bunch of other callers also want to just restore a single crtc, add a
boolean to disable checking only where it doesn't make sense.
Note that intel_modeset_setup_hw_state already has a call to
intel_modeset_check_state at the end, so we don't reduce the amount of
checking.
v2: Try harder not to create a big patch (Chris).
v3: Even smaller (still Chris). Also fix a trailing space.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://lkml.org/lkml/2013/3/16/60
Cc: Tomas Melin <tomas.melin@iki.fi>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomas Melin <tomas.melin@iki.fi>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4615d4c9e2 upstream.
Enabling context support increases SwapBuffers latency by about 20%
(measured on an i7-3720qm). We can offset that loss slightly by enabling
faster caching for the contexts. As they are not backed by any
particular cache (such as the sampler or render caches) our only option
is to select the generic mid-level cache. This reduces the latency of
the swap by about 5%.
Oddly this effect can be observed running smokin-guns on IVB at
1280x1024:
Using BLT copies for swaps: 151.67 fps
Using Render copies for swaps (unpatched): 141.70 fps
With contexts disabled: 150.23 fps
With contexts in L3$: 150.77 fps
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25ff1195f8 upstream.
In order to fully serialize access to the fenced region and the update
to the fence register we need to take extreme measures on SNB+, and
manually flush writes to memory prior to writing the fence register in
conjunction with the memory barriers placed around the register write.
Fixes i-g-t/gem_fence_thrash
v2: Bring a bigger gun
v3: Switch the bigger gun for heavier bullets (Arjan van de Ven)
v4: Remove changes for working generations.
v5: Reduce to a per-cpu wbinvd() call prior to updating the fences.
v6: Rewrite comments to ellide forgotten history.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=62191
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Tested-by: Jon Bloomfield <jon.bloomfield@intel.com> (v2)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a7d1fb79f upstream.
The connector associated with the encoder is considered active when the
output associtated with this connector is active on the encoder. The
encoder itself is considered active when either there is an active
output on it or the respective SDVO channel is active.
Having active outputs when the SDVO channel is inactive seems to be
inconsistent: such states can be found when intel_modeset_setup_hw_state()
collects the hardware state set by the BIOS.
This inconsistency will be fixed in intel_sanitize_crtc()
(when intel_crtc_update_dpms() is called), this however only happens
when the encoder is associated with a crtc.
This patch also reverts:
commit bd6946e87a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 2 21:30:34 2013 +0200
drm/i915: Fix sdvo connector get_hw_state function
Signed-off-by: Egbert Eich <eich@suse.de>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63031
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e9dd0e889 upstream.
The "Mobile Sandy Bridge CPUs" in the Fujitsu Esprimo Q900
mini desktop PCs are probably misleading the LVDS detection
code in intel_lvds_supported. Nothing is connected to the
LVDS ports in these systems.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 306373b645 upstream.
Port over the mgag200 fix to ast as it suffers the same issue.
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 219b47339c upstream.
Currently we have a problem with this:
1. i915: create gem object
2. i915: export gem object to prime
3. radeon: import gem object
4. close prime fd
5. radeon: unref object
6. i915: unref object
i915 has an imported object reference in its file priv, that isn't
cleaned up properly until fd close. The reference gets added at step 2,
but at step 6 we don't have enough info to clean it up.
The solution is to take a reference on the dma-buf when we export it,
and drop the reference when the gem handle goes away.
So when we export a dma_buf from a gem object, we keep track of it
with the handle, we take a reference to the dma_buf. When we close
the handle (i.e. userspace is finished with the buffer), we drop
the reference to the dma_buf, and it gets collected.
This patch isn't meant to fix any other problem or bikesheds, and it doesn't
fix any races with other scenarios.
v1.1: move export symbol line back up.
v2: okay I had to do a bit more, as the first patch showed a leak
on one of my tests, that I found using the dma-buf debugfs support,
the problem case is exporting a buffer twice with the same handle,
we'd add another export handle for it unnecessarily, however
we now fail if we try to export the same object with a different gem handle,
however I'm not sure if that is a case I want to support, and I've
gotten the code to WARN_ON if we hit something like that.
v2.1: rebase this patch, write better commit msg.
v3: cleanup error handling, track import vs export in linked list,
these two patches were separate previously, but seem to work better
like this.
v4: danvet is correct, this code is no longer useful, since the buffer
better exist, so remove it.
v5: always take a reference to the dma buf object, import or export.
(Imre Deak contributed this originally)
v6: square the circle, remove import vs export tracking now
that there is no difference
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 011c2282c7 upstream.
In commit be8a42ae60 we inroduced a refcount problem, where on the
drm_gem_prime_fd_to_handle() error path we'll call dma_buf_put() for
self imported dma buffers.
Fix this by taking a reference on the dma buffer in the .gem_import
hook instead of assuming the caller had taken one. Besides fixing the
bug this is also more logical.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e127dc28cc upstream.
Backlight hotkeys weren't working before on certain cedartrail laptops.
The source of this problem is that the hotkeys' ASLE opregion interrupts
were simply ignored. Driver seemed to expect the interrupt to be
associated with a pipe, but it wasn't.
Accepting the ASLE interrupt without an associated pipe event flag fixes
the issue, the backlight code is called when needed, making the
brightness keys work properly.
[patrik: This patch affects irq handling on any netbook with opregion support]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=833597
Reference: http://lists.freedesktop.org/archives/dri-devel/2012-July/025279.html
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6417195995 upstream.
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3b2bbdc8a upstream.
Port over the mgag200 fix to cirrus as it suffers the same issue.
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 871dd9286e upstream.
linux-v3.8-rc1 and later support for plug for blkdev_issue_discard with
commit 0cfbcafcae
(block: add plug for blkdev_issue_discard )
For example,
1) DISCARD rq-1 with size size 4GB
2) DISCARD rq-2 with size size 1GB
If these 2 discard requests get merged, final request size will be 5GB.
In this case, request's __data_len field may overflow as it can store
max 4GB(unsigned int).
This issue was observed while doing mkfs.f2fs on 5GB SD card:
https://lkml.org/lkml/2013/4/1/292
Info: sector size = 512
Info: total sectors = 11370496 (in 512bytes)
Info: zone aligned segment0 blkaddr: 512
[ 257.789764] blk_update_request: bio idx 0 >= vcnt 0
mkfs process gets stuck in D state and I see the following in the dmesg:
[ 257.789733] __end_that: dev mmcblk0: type=1, flags=122c8081
[ 257.789764] sector 4194304, nr/cnr 2981888/4294959104
[ 257.789764] bio df3840c0, biotail df3848c0, buffer (null), len
1526726656
[ 257.789764] blk_update_request: bio idx 0 >= vcnt 0
[ 257.794921] request botched: dev mmcblk0: type=1, flags=122c8081
[ 257.794921] sector 4194304, nr/cnr 2981888/4294959104
[ 257.794921] bio df3840c0, biotail df3848c0, buffer (null), len
1526726656
This patch fixes this issue.
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e7f7bcc3f upstream.
ESR.WnR bit is always set on data cache maintenance faults even though
the page is not required to have write permission. If a translation
fault (page not yet mapped) happens for read-only user address range,
Linux incorrectly assumes a permission fault. This patch adds the check
of the ESR.CM bit during the page fault handling to ignore the 'write'
flag.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Tim Northover <Tim.Northover@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c449bbc6 upstream.
When compiling kernel with -jN (N > 1), all warning/error messages
printed while openssl is generating key pair may get mixed dots and
other symbols openssl sends to stderr. This patch makes sure openssl
logs go to default stdout.
Example of the garbage on stderr:
crypto/anubis.c:581: warning: ‘inter’ is used uninitialized in this function
Generating a 4096 bit RSA private key
.........
drivers/gpu/drm/i915/i915_gem_gtt.c: In function ‘gen6_ggtt_insert_entries’:
drivers/gpu/drm/i915/i915_gem_gtt.c:440: warning: ‘addr’ may be used uninitialized in this function
.net/mac80211/tx.c: In function ‘ieee80211_subif_start_xmit’:
net/mac80211/tx.c:1780: warning: ‘chanctx_conf’ may be used uninitialized in this function
..drivers/isdn/hardware/mISDN/hfcpci.c: In function ‘hfcpci_softirq’:
.....drivers/isdn/hardware/mISDN/hfcpci.c:2298: warning: ignoring return value of ‘driver_for_each_device’, declared with attribute warn_unused_result
Signed-off-by: David Cohen <david.a.cohen@intel.com>
Reviewed-by: mark gross <mark.gross@intel.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13f85203e1 upstream.
Some ancient pHyp versions used to create a 8 bytes local-mac-address
property in the device-tree instead of a 6 bytes one for veth.
The Linux driver code to deal with that is an insane hack which also
happens to break with some choices of MAC addresses in qemu by testing
for a bit in the address rather than just looking at the size of the
property.
Sanitize this by doing the latter instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af73e4d950 upstream.
The current kernel returns -EINVAL unless a given mmap length is
"almost" hugepage aligned. This is because in sys_mmap_pgoff() the
given length is passed to vm_mmap_pgoff() as it is without being aligned
with hugepage boundary.
This is a regression introduced in commit 40716e2924 ("hugetlbfs: fix
alignment of huge page requests"), where alignment code is pushed into
hugetlb_file_setup() and the variable len in caller side is not changed.
To fix this, this patch partially reverts that commit, and adds
alignment code in caller side. And it also introduces hstate_sizelog()
in order to get proper hstate to specified hugepage size.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=56881
[akpm@linux-foundation.org: fix warning when CONFIG_HUGETLB_PAGE=n]
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: <iceman_dvd@yahoo.com>
Cc: Steven Truelove <steven.truelove@utoronto.ca>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce8a5dbdf9 upstream.
When checking if an autofs mount point is busy it isn't sufficient to
only check if it's a mount point.
For example, if the mount of an offset mountpoint in a tree is denied
for this host by its export and the dentry becomes a process working
directory the check incorrectly returns the mount as not in use at
expire.
This can happen since the default when mounting within a tree is
nostrict, which means ingnore mount fails on mounts within the tree and
continue. The nostrict option is meant to allow mounting in this case.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7122beeee7 upstream.
The following commit breaks numa distance setup for old powerpc
systems that use form0 encoding in device tree.
commit 41eab6f88f
powerpc/numa: Use form 1 affinity to setup node distance
Device tree node /rtas/ibm,associativity-reference-points would
index into /cpus/PowerPCxxxx/ibm,associativity based on form0 or
form1 encoding detected by ibm,architecture-vec-5 property.
All modern systems use form1 and current kernel code is correct.
However, on older systems with form0 encoding, the numa distance
will get hard coded as LOCAL_DISTANCE for all nodes. This causes
task scheduling anomaly since scheduler will skip building numa
level domain (topmost domain with all cpus) if all numa distances
are same. (value of 'level' in sched_init_numa() will remain 0)
Prior to the above commit:
((from) == (to) ? LOCAL_DISTANCE : REMOTE_DISTANCE)
Restoring compatible behavior with this patch for old powerpc systems
with device tree where numa distance are encoded as form0.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73d2fb758e upstream.
POWER8 allows read and write of the DSCR in userspace. We added
kernel emulation so applications could always use the instructions
regardless of the CPU type.
Unfortunately there are two SPRs for the DSCR and we only added
emulation for the privileged one. Add code to match the non
privileged one.
A simple test was created to verify the fix:
http://ozlabs.org/~anton/junkcode/user_dscr_test.c
Without the patch we get a SIGILL and it passes with the patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6cc25fda5 upstream.
The adp5520 unfortunately also clears the BL_EN bit when the nSTNDBY bit is
cleared. So we need to make sure to restore it during resume if it was set
before suspend.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdbc5d0c60 upstream.
The driver is doing, by default, multi-block reads. When a block error
occurs, card/block.c instigates a single block read: "mmcblk0: retrying
using single block read". It leaves the sg chain intact and just changes
the length attribute for the first sg entry and the overall sg_len
parameter. When atmci_read_data_pio is called to read the single block
of data it ignores the sg_len and expects to read more than 512 bytes as
it sees there are multiple items in the sg list. No more data comes as
the controller has only been commanded to get one block.
Signed-off-by: Terry Barnaby <terry@beam.ltd.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 836dc2fe89 upstream.
PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data. Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.
Only affects old emmc devices - pre 4.4 devices.
Reported-by: Elad Yi <elad.yi@gmail.com>
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660696d1d1 upstream.
Source operand for one byte mov[zs]x is decoded incorrectly if it is in
high byte register. Fix that.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91cf54feec upstream.
Fix regression introduced by commit 796211b795 ("mmc: atmel-mci: add
pdc support and runtime capabilities detection") which removed the need
for CONFIG_MMC_ATMELMCI_DMA but kept the Kconfig-entry as well as the
compile guards around dma_release_channel() in remove(). Consequently,
DMA is always enabled (if supported), but the DMA-channel is not
released on module unload unless the DMA-config option is selected.
Remove the no longer used CONFIG_MMC_ATMELMCI_DMA option completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f3e3c7cfc upstream.
Fox the Kconfig documentation for CONFIG_EXT4_DEBUG to match the
change made by commit a0b30c1229: ext4: use module parameters instead
of debugfs for mballoc_debug
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5c72d814c upstream.
Commit fb0a387dcd restricts block allocations for indirect-mapped
files to block groups less than s_blockfile_groups. However, the
online resizing code wasn't setting s_blockfile_groups, so the newly
added block groups were not available for non-extent mapped files.
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d76a3a7711 upstream.
In the case where an inode has a very stale transaction id (tid) in
i_datasync_tid or i_sync_tid, it's possible that after a very large
(2**31) number of transactions, that the tid number space might wrap,
causing tid_geq()'s calculations to fail.
Commit deeeaf13 "jbd2: fix fsync() tid wraparound bug", later modified
by commit e7b04ac0 "jbd2: don't wake kjournald unnecessarily",
attempted to fix this problem, but it only avoided kjournald spinning
forever by fixing the logic in jbd2_log_start_commit().
Unfortunately, in the codepaths in fs/ext4/fsync.c and fs/ext4/inode.c
that might call jbd2_log_start_commit() with a stale tid, those
functions will subsequently call jbd2_log_wait_commit() with the same
stale tid, and then wait for a very long time. To fix this, we
replace the calls to jbd2_log_start_commit() and
jbd2_log_wait_commit() with a call to a new function,
jbd2_complete_transaction(), which will correctly handle stale tid's.
As a bonus, jbd2_complete_transaction() will avoid locking
j_state_lock for writing unless a commit needs to be started. This
should have a small (but probably not measurable) improvement for
ext4's scalability.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: George Barnett <gbarnett@atlassian.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d77df715 upstream.
During early init, we would incorrectly set the NX bit even if the NX
feature was not supported. Instead, only set this bit if NX is
actually available and enabled. We already do very early detection of
the NX bit to enable it in EFER, this simply extends this detection to
the early page table mask.
Reported-by: Fernando Luis Vázquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1367476850.5660.2.camel@nexus
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73e3dd6b45 upstream.
The PTP Hardware Clock settime function in the e1000e driver
computes nanoseconds from a struct timespec. The code converts the
seconds field .tv_sec by multiplying it with NSEC_PER_SEC. However,
both operands are of type long, resulting in an unintended overflow.
The patch fixes the issue by using the helper function from time.h.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d87d830720 upstream.
Previously, the ixgbe_msix_other was writing the full 32bits of the set
interrupts, instead of only the ones which the ixgbe_msix_other is
handling. This resulted in a loss of performance when the X540's PPS feature is
enabled due to sometimes clearing queue interrupts which resulted in the driver
not getting the interrupt for cleaning the q_vector rings often enough. The fix
is to simply mask the lower 16bits off so that this handler does not write them
in the EICR, which causes them to remain high and be properly handled by the
clean_rings interrupt routine as normal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d69f3bad46 upstream.
Trying to run an application which was trying to put data into half of
memory using shmget(), we found that having a shmall value below 8EiB-8TiB
would prevent us from using anything more than 8TiB. By setting
kernel.shmall greater than 8EiB-8TiB would make the job work.
In the newseg() function, ns->shm_tot which, at 8TiB is INT_MAX.
ipc/shm.c:
458 static int newseg(struct ipc_namespace *ns, struct ipc_params *params)
459 {
...
465 int numpages = (size + PAGE_SIZE -1) >> PAGE_SHIFT;
...
474 if (ns->shm_tot + numpages > ns->shm_ctlall)
475 return -ENOSPC;
[akpm@linux-foundation.org: make ipc/shm.c:newseg()'s numpages size_t, not int]
Signed-off-by: Robin Holt <holt@sgi.com>
Reported-by: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 990de49f74 upstream.
When a full scan 2.4 and 5 GHz scan is scheduled, but then the 2.4 GHz
part of the scan disables a 5.2 GHz channel due to, e.g. receiving
country or frequency information, that 5.2 GHz channel might already
be in the list of channels to scan next. Then, when the driver checks
if it should do a passive scan, that will return false and attempt an
active scan. This is not only wrong but can also lead to the iwlwifi
device firmware crashing since it checks regulatory as well.
Fix this by not setting the channel flags to just disabled but rather
OR'ing in the disabled flag. That way, even if the race happens, the
channel will be scanned passively which is still (mostly) correct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf8d909705 upstream.
The seconds field of an nfstime4 structure is 64bit, but we are assuming
that the first 32bits are zero-filled. So if the client tries to set
atime to a value before the epoch (touch -t 196001010101), then the
server will save the wrong value on disk.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c7c3e67ab upstream.
Don't actually close any opens until we don't need them at all.
This means being left with write access when it's not really necessary,
but that's better than putting a file that might still have posix locks
held on it, as we have been.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b6cc4d6f8 upstream.
A server shouldn't normally return NFS4ERR_GRACE if the client holds a
delegation, since no conflicting lock reclaims can be granted, however
the spec does not require the server to grant the open in this
instance
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbb21c25a3 upstream.
A server shouldn't normally return NFS4ERR_GRACE if the client holds a
delegation, since no conflicting lock reclaims can be granted, however
the spec does not require the server to grant the lock in this
instance.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32f9f570d0 upstream.
In SSD/hard disk hybid storage, discard request should be ignored for hard
disk. We used to be doing this way, but the unplug path forgets it.
This is suitable for stable tree since v3.6.
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 486adf72cc upstream.
Maintenance of a bad-block-list currently defaults to 'enabled'
and is then disabled when it cannot be supported.
This is backwards and causes problem for dm-raid which didn't know
to disable it.
So fix the defaults, and only enabled for v1.x metadata which
explicitly has bad blocks enabled.
The problem with dm-raid has been present since badblock support was
added in v3.1, so this patch is suitable for any -stable from 3.1
onwards.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dfd89af86 upstream.
After a server reboot, the reclaimer thread will recover all the existing
locks. For locks that are blocked, however, it will change the value
of block->b_status to nlm_lck_denied_grace_period in order to signal that
they need to wake up and resend the original blocking lock request.
Due to a bug, however, the block->b_status never gets reset after the
blocked locks have been woken up, and so the process goes into an
infinite loop of resends until the blocked lock is satisfied.
Reported-by: Marc Eshel <eshel@us.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e56fb28740 upstream.
threadgroup_lock() takes signal->cred_guard_mutex to ensure that
thread_group_leader() is stable. This doesn't look nice, the scope of
this lock in do_execve() is huge.
And as Dave pointed out this can lead to deadlock, we have the
following dependencies:
do_execve: cred_guard_mutex -> i_mutex
cgroup_mount: i_mutex -> cgroup_mutex
attach_task_by_pid: cgroup_mutex -> cred_guard_mutex
Change de_thread() to take threadgroup_change_begin() around the
switch-the-leader code and change threadgroup_lock() to avoid
->cred_guard_mutex.
Note that de_thread() can't sleep with ->group_rwsem held, this can
obviously deadlock with the exiting leader if the writer is active, so it
does threadgroup_change_end() before schedule().
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 421348f1ca upstream.
Call cond_resched() in shrink_dcache_parent() to maintain interactivity.
Before this patch:
void shrink_dcache_parent(struct dentry * parent)
{
while ((found = select_parent(parent, &dispose)) != 0)
shrink_dentry_list(&dispose);
}
select_parent() populates the dispose list with dentries which
shrink_dentry_list() then deletes. select_parent() carefully uses
need_resched() to avoid doing too much work at once. But neither
shrink_dcache_parent() nor its called functions call cond_resched(). So
once need_resched() is set select_parent() will return single dentry
dispose list which is then deleted by shrink_dentry_list(). This is
inefficient when there are a lot of dentry to process. This can cause
softlockup and hurts interactivity on non preemptable kernels.
This change adds cond_resched() in shrink_dcache_parent(). The benefit
of this is that need_resched() is quickly cleared so that future calls
to select_parent() are able to efficiently return a big batch of dentry.
These additional cond_resched() do not seem to impact performance, at
least for the workload below.
Here is a program which can cause soft lockup if other system activity
sets need_resched().
int main()
{
struct rlimit rlim;
int i;
int f[100000];
char buf[20];
struct timeval t1, t2;
double diff;
/* cleanup past run */
system("rm -rf x");
/* boost nfile rlimit */
rlim.rlim_cur = 200000;
rlim.rlim_max = 200000;
if (setrlimit(RLIMIT_NOFILE, &rlim))
err(1, "setrlimit");
/* make directory for files */
if (mkdir("x", 0700))
err(1, "mkdir");
if (gettimeofday(&t1, NULL))
err(1, "gettimeofday");
/* populate directory with open files */
for (i = 0; i < 100000; i++) {
snprintf(buf, sizeof(buf), "x/%d", i);
f[i] = open(buf, O_CREAT);
if (f[i] == -1)
err(1, "open");
}
/* close some of the files */
for (i = 0; i < 85000; i++)
close(f[i]);
/* unlink all files, even open ones */
system("rm -rf x");
if (gettimeofday(&t2, NULL))
err(1, "gettimeofday");
diff = (((double)t2.tv_sec * 1000000 + t2.tv_usec) -
((double)t1.tv_sec * 1000000 + t1.tv_usec));
printf("done: %g elapsed\n", diff/1e6);
return 0;
}
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04df32fa10 upstream.
When we run the crackerjack testsuite, the inotify_add_watch test is
stalled.
This is caused by the invalid mask 0 - the task is waiting for the event
but it never comes. inotify_add_watch() should return -EINVAL as it did
before commit 676a0675cf ("inotify: remove broken mask checks causing
unmount to be EINVAL"). That commit removes the invalid mask check, but
that check is needed.
Check the mask's ALL_INOTIFY_BITS before the inotify_arg_to_mask() call.
If none are set, just return -EINVAL.
Because IN_UNMOUNT is in ALL_INOTIFY_BITS, this change will not trigger
the problem that above commit fixed.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Acked-by: Jim Somerville <Jim.Somerville@windriver.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cc1144a31 upstream.
mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find
the module name of a disk driver. Current name is "highbank-ahci" but
the module is "sata_highbank". Rename it to match the module name.
Signed-off-by: Robert Richter <robert.richter@calxeda.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f7a05d701 upstream.
Vitaliy reported that a per cpu HPET timer interrupt crashes the
system during hibernation. What happens is that the per cpu HPET timer
gets shut down when the nonboot cpus are stopped. When the nonboot
cpus are onlined again the HPET code sets up the MSI interrupt which
fires before the clock event device is registered. The event handler
is still set to hrtimer_interrupt, which then crashes the machine due
to highres mode not being active.
See http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=700333
There is no real good way to avoid that in the HPET code. The HPET
code alrady has a mechanism to detect spurious interrupts when event
handler == NULL for a similar reason.
We can handle that in the clockevent/tick layer and replace the
previous functional handler with a dummy handler like we do in
tick_setup_new_device().
The original clockevents code did this in clockevents_exchange_device(),
but that got removed by commit 7c1e76897 (clockevents: prevent
clockevent event_handler ending up handler_noop) which forgot to fix
it up in tick_shutdown(). Same issue with the broadcast device.
Reported-by: Vitaliy Fillipov <vitalif@yourcmc.ru>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: 700333@bugs.debian.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ced9cb1af1 upstream.
A bug was reported that caused localmodconfig to not keep all the
dependencies of ATH9K. This was caused by the kconfig file:
In drivers/net/wireless/ath/Kconfig:
commit 712317ad97 upstream.
We should store file xattrs in struct cfent instead of struct cftype,
because cftype is a type while cfent is object instance of cftype.
For example each cgroup has a tasks file, and each tasks file is
associated with a uniq cfent, but all those files share the same
struct cftype.
Alexey Kodanev reported a crash, which can be reproduced:
# mount -t cgroup -o xattr /sys/fs/cgroup
# mkdir /sys/fs/cgroup/test
# setfattr -n trusted.value -v test_value /sys/fs/cgroup/tasks
# rmdir /sys/fs/cgroup/test
# umount /sys/fs/cgroup
oops!
In this case, simple_xattrs_free() will free the same struct simple_xattrs
twice.
tj: Dropped unused local variable @cft from cgroup_diput().
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ac1707a13 upstream.
The 3rd parameter of flex_array_prealloc() is the number of elements,
not the index of the last element.
The effect of the bug is, when opening cgroup.procs, a flex array will
be allocated and all elements of the array is allocated with
GFP_KERNEL flag, but the last one is GFP_ATOMIC, and if we fail to
allocate memory for it, it'll trigger a BUG_ON().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94a4093195 upstream.
Commit 4ae46be "Thermal: Introduce thermal_zone_trip_update()"
introduced a regression causing the fan to be always on even when
the system is idle.
My original idea in that commit is that:
- when the current temperature is above the trip point,
keep the fan on, even if the temperature is dropping.
- when the current temperature is below the trip point,
turn on the fan when the temperature is raising,
turn off the fan when the temperature is dropping.
But this is what the code actually does:
- when the current temperature is above the trip point,
the fan keeps on.
- when the current temperature is below the trip point,
the fan is always on because thermal_get_trend()
in driver/acpi/thermal.c returns THERMAL_TREND_RAISING.
Thus the fan keeps running even if the system is idle.
Fix this in drivers/acpi/thermal.c.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56591
References: https://bugzilla.kernel.org/show_bug.cgi?id=56601
References: https://bugzilla.kernel.org/show_bug.cgi?id=50041#c45
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Tested-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6432ded29 upstream.
Commit 53aac44 (ACPI: Store valid ACPI tables passed via early initrd
in reserved memblock areas) introduced acpi_initrd_override() that
passes a wrong value as the second argument to memblock_reserve().
Namely, the second argument of memblock_reserve() is the size of the
region, not the address of the top of it, so make
acpi_initrd_override() pass the size in there as appropriate.
[rjw: Changelog]
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66af4df08 upstream.
Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace
walk, which requires acquiring an acpi namespace mutex. This made it
impossible to be used when calling path has held a spinlock.
For example, it can occur in the following code path for pata_acpi:
ata_scsi_queuecmd (ap->lock is acquired)
__ata_scsi_queuecmd
ata_scsi_translate
ata_qc_issue
pacpi_qc_issue
ata_acpi_stm
ata_ap_acpi_handle
acpi_get_child
acpi_walk_namespace
acpi_ut_acquire_mutex (acquire mutex while holding lock)
This caused scheduling while atomic bug, as reported in bug #56781.
Actually, ata_ap_acpi_handle doesn't have to walk the namespace every
time it is called, it can simply return the bound acpi handle on the
corresponding SCSI host. The reason previously it is not done this way
is, ata_ap_acpi_handle is used in the binding function
ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the
SCSI host yet. Since we already have the ATA port's handle in its
binding function, we can simply use it instead of calling
ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm,
where it will receive an acpi handle param in addition to the ATA port
which is solely used for debug statement. With this change, we can make
ata_ap_acpi_handle simply return the bound handle for SCSI host instead
of walking the acpi namespace now.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781
Reported-and-tested-by: <kenzopl@o2.pl>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e005715efa upstream.
There's a bug where rtc alarms are ignored after the rtc cmos suspends
but before the system finishes suspend. Since hpet emulation is
disabled and it still handles the interrupts, a wake event is never
registered which is done from the rtc layer.
This patch reverts commit d1b2efa83f ("rtc: disable hpet emulation on
suspend") which disabled hpet emulation. To fix the problem mentioned
in that commit, hpet_rtc_timer_init() is called directly on resume.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cdc444a67 upstream.
As pointed out by Andrew Morton, the swap-over-NFS writeback is not
setting PageWriteback before it is queued for direct IO. While swap
pages do not participate in BDI or process dirty accounting and the IO
is synchronous, the writeback bit is still required and not setting it
in this case was an oversight. swapoff depends on the page writeback to
synchronoise all pending writes on a swap page before it is reused.
Swapcache freeing and reuse depend on checking the PageWriteback under
lock to ensure the page is safe to reuse.
Direct IO handlers and the direct IO handler for NFS do not deal with
PageWriteback as they are synchronous writes. In the case of NFS, it
schedules pages (or a page in the case of swap) for IO and then waits
synchronously for IO to complete in nfs_direct_write(). It is
recognised that this is a slowdown from normal swap handling which is
asynchronous and uses a completion handler. Shoving PageWriteback
handling down into direct IO handlers looks like a bad fit to handle the
swap case although it may have to be dealt with some day if swap is
converted to use direct IO in general and bmap is finally done away
with. At that point it will be necessary to refit asynchronous direct
IO with completion handlers onto the swap subsystem.
As swapcache currently depends on PageWriteback to protect against
races, this patch sets PageWriteback under the page lock before queueing
it for direct IO. It is cleared when the direct IO handler returns. IO
errors are treated similarly to the direct-to-bio case except PageError
is not set as in the case of swap-over-NFS, it is likely to be a
transient error.
It was asked what prevents such a page being reclaimed in parallel.
With this patch applied, such a page will now be skipped (most of the
time) or blocked until the writeback completes. Reclaim checks
PageWriteback under the page lock before calling try_to_free_swap and
the page lock should prevent the page being requeued for IO before it is
freed.
This and Jerome's related patch should considered for -stable as far
back as 3.6 when swap-over-NFS was introduced.
[akpm@linux-foundation.org: use pr_err_ratelimited()]
[akpm@linux-foundation.org: remove hopefully-unneeded cast in printk]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d30d31ea3 upstream.
Since commit 62c230bc17 ("mm: add support for a filesystem to activate
swap files and use direct_IO for writing swap pages"), swap_writepage()
calls direct_IO on swap files. However, in that case the page isn't
redirtied if I/O fails, and is therefore handled afterwards as if it has
been successfully written to the swap file, leading to memory corruption
when the page is eventually swapped back in.
This patch sets the page dirty when direct_IO() fails. It fixes a
memory corruption that happened while using swap-over-NFS.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f294b5a13 upstream.
The settimeofday01 test in the LTP testsuite effectively does
gettimeofday(current time);
settimeofday(Jan 1, 1970 + 100 seconds);
settimeofday(current time);
This test causes a stack trace to be displayed on the console during the
setting of timeofday to Jan 1, 1970 + 100 seconds:
[ 131.066751] ------------[ cut here ]------------
[ 131.096448] WARNING: at kernel/time/clockevents.c:209 clockevents_program_event+0x135/0x140()
[ 131.104935] Hardware name: Dinar
[ 131.108150] Modules linked in: sg nfsv3 nfs_acl nfsv4 auth_rpcgss nfs dns_resolver fscache lockd sunrpc nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 iptable_nat nf_nat_ipv4 nf_nat iptable_mangle ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter ip_tables kvm_amd kvm sp5100_tco bnx2 i2c_piix4 crc32c_intel k10temp fam15h_power ghash_clmulni_intel amd64_edac_mod pcspkr serio_raw edac_mce_amd edac_core microcode xfs libcrc32c sr_mod sd_mod cdrom ata_generic crc_t10dif pata_acpi radeon i2c_algo_bit drm_kms_helper ttm drm ahci pata_atiixp libahci libata usb_storage i2c_core dm_mirror dm_region_hash dm_log dm_mod
[ 131.176784] Pid: 0, comm: swapper/28 Not tainted 3.8.0+ #6
[ 131.182248] Call Trace:
[ 131.184684] <IRQ> [<ffffffff810612af>] warn_slowpath_common+0x7f/0xc0
[ 131.191312] [<ffffffff8106130a>] warn_slowpath_null+0x1a/0x20
[ 131.197131] [<ffffffff810b9fd5>] clockevents_program_event+0x135/0x140
[ 131.203721] [<ffffffff810bb584>] tick_program_event+0x24/0x30
[ 131.209534] [<ffffffff81089ab1>] hrtimer_interrupt+0x131/0x230
[ 131.215437] [<ffffffff814b9600>] ? cpufreq_p4_target+0x130/0x130
[ 131.221509] [<ffffffff81619119>] smp_apic_timer_interrupt+0x69/0x99
[ 131.227839] [<ffffffff8161805d>] apic_timer_interrupt+0x6d/0x80
[ 131.233816] <EOI> [<ffffffff81099745>] ? sched_clock_cpu+0xc5/0x120
[ 131.240267] [<ffffffff814b9ff0>] ? cpuidle_wrap_enter+0x50/0xa0
[ 131.246252] [<ffffffff814b9fe9>] ? cpuidle_wrap_enter+0x49/0xa0
[ 131.252238] [<ffffffff814ba050>] cpuidle_enter_tk+0x10/0x20
[ 131.257877] [<ffffffff814b9c89>] cpuidle_idle_call+0xa9/0x260
[ 131.263692] [<ffffffff8101c42f>] cpu_idle+0xaf/0x120
[ 131.268727] [<ffffffff815f8971>] start_secondary+0x255/0x257
[ 131.274449] ---[ end trace 1151a50552231615 ]---
When we change the system time to a low value like this, the value of
timekeeper->offs_real will be a negative value.
It seems that the WARN occurs because an hrtimer has been started in the time
between the releasing of the timekeeper lock and the IPI call (via a call to
on_each_cpu) in clock_was_set() in the do_settimeofday() code. The end result
is that a REALTIME_CLOCK timer has been added with softexpires = expires =
KTIME_MAX. The hrtimer_interrupt() fires/is called and the loop at
kernel/hrtimer.c:1289 is executed. In this loop the code subtracts the
clock base's offset (which was set to timekeeper->offs_real in
do_settimeofday()) from the current hrtimer_cpu_base->expiry value (which
was KTIME_MAX):
KTIME_MAX - (a negative value) = overflow
A simple check for an overflow can resolve this problem. Using KTIME_MAX
instead of the overflow value will result in the hrtimer function being run,
and the reprogramming of the timer after that.
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
[jstultz: Tweaked commit subject]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51fd36f3fa upstream.
One can trigger an overflow when using ktime_add_ns() on a 32bit
architecture not supporting CONFIG_KTIME_SCALAR.
When passing a very high value for u64 nsec, e.g. 7881299347898368000
the do_div() function converts this value to seconds (7881299347) which
is still to high to pass to the ktime_set() function as long. The result
in is a negative value.
The problem on my system occurs in the tick-sched.c,
tick_nohz_stop_sched_tick() when time_delta is set to
timekeeping_max_deferment(). The check for time_delta < KTIME_MAX is
valid, thus ktime_add_ns() is called with a too large value resulting in
a negative expire value. This leads to an endless loop in the ticker code:
time_delta: 7881299347898368000
expires = ktime_add_ns(last_update, time_delta)
expires: negative value
This fix caps the value to KTIME_MAX.
This error doesn't occurs on 64bit or architectures supporting
CONFIG_KTIME_SCALAR (e.g. ARM, x86-32).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
[jstultz: Minor tweaks to commit message & header]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65033cc8d5 upstream.
When we have a loopback mixer control, this should manage the state
whether the output paths include the aamix or not. But the current
code blindly initializes the output paths with aamix = true, thus the
aamix is enabled unless the loopback mixer control is changed.
Also, update_aamix_paths() called by the loopback mixer control put
callback invokes snd_hda_activate_path() with aamix = true even for
disabling the mixing. This leaves the aamix path even though the
loopback control is turned off.
This patch fixes these issues:
- Introduced aamix_default() helper to indicate whether with_aamix is
true or false as default
- Fix the argument in update_aamix_paths() for disabling loopback
Reported-by: Lydia Wang <LydiaWang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c75c5ab575 upstream.
The recent changes in the USB API ("implement new semantics for
URB_ISO_ASAP") made the former meaning of the URB_ISO_ASAP flag the
default, and changed this flag to mean that URBs can be delayed.
This is not the behaviour wanted by any of the audio drivers because
it leads to discontinuous playback with very small period sizes.
Therefore, our URBs need to be submitted without this flag.
Reported-by: Joe Rayhawk <jrayhawk@fairlystable.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60af3d037e upstream.
We've got strange errors in get_ctl_value() in mixer.c during
probing, e.g. on Hercules RMX2 DJ Controller:
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x201, wIndex = 0xa00, type = 4
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x200, wIndex = 0xa00, type = 4
....
It turned out that the culprit is autopm: snd_usb_autoresume() returns
-ENODEV when called during card->probing = 1.
Since the call itself during card->probing = 1 is valid, let's fix the
return value of snd_usb_autoresume() as success.
Reported-and-tested-by: Daniel Schürmann <daschuer@mixxx.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbc200bca4 upstream.
Commit 88a8516a21 (ALSA: usbaudio: implement USB autosuspend)
introduced autopm for all USB audio/MIDI devices. However, many MIDI
devices, such as synthesizers, do not merely transmit MIDI messages but
use their MIDI inputs to control other functions. With autopm, these
devices would get powered down as soon as the last MIDI port device is
closed on the host.
Even some plain MIDI interfaces could get broken: they automatically
send Active Sensing messages while powered up, but as soon as these
messages cease, the receiving device would interpret this as an
accidental disconnection.
Commit f5f165418c (ALSA: usb-audio: Fix missing autopm for MIDI input)
introduced another regression: some devices (e.g. the Roland GAIA SH-01)
are self-powered but do a reset whenever the USB interface's power state
changes.
To work around all this, just disable autopm for all USB MIDI devices.
Reported-by: Laurens Holst
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1539d4f82a upstream.
When recording at 176.2KHz or 192Khz, the device adds a 32-bit length
header to the capture packets, which obviously needs to be ignored for
recording to work properly.
Userspace expected: L0 L1 L2 R0 R1 R2
...but actually got: R2 L0 L1 L2 R0 R1
Also, the last byte of the length header being interpreted as L0 of
the first sample caused spikes every 0.5ms, resulting in a loud 16KHz
tone (about the highest 'B' on a piano) being present throughout
captures.
Tested at all sample rates on an E-Mu 0404USB, and tested for
regressions on a generic USB headset.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebfc594c02 upstream.
The USB_DT_CS_ENDPOINT class-specific endpoint descriptor is usually
stuffed directly after the standard USB endpoint descriptor, and this is
where the driver currently expects it to be.
There are, however, devices in the wild that have it the other way
around in their descriptor sets, so the USB_DT_CS_ENDPOINT comes
*before* the standard enpoint. Devices known to implement it that way
are "Sennheiser BTD-500" and Plantronics USB headsets.
When the driver can't find the USB_DT_CS_ENDPOINT, it won't be able to
change sample rates, as the bitmask for the validity of this command is
storen in bmAttributes of that descriptor.
Fix this by searching the entire interface instead of just the extra
bytes of the first endpoint, in case the latter fails.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Torstein Hegge <hegge@resisty.net>
Reported-and-tested-by: Yves G <alsa-user@vivigatt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d33b29ba upstream.
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Dirk Hohndel <dirk@hohndel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ee8630e02 upstream.
On architectures where a pgd entry may be shared between user and kernel
(e.g. ARM+LPAE), freeing page tables needs a ceiling other than 0.
This patch introduces a generic USER_PGTABLES_CEILING that arch code can
override. It is the responsibility of the arch code setting the ceiling
to ensure the complete freeing of the page tables (usually in
pgd_free()).
[catalin.marinas@arm.com: commit log; shift_arg_pages(), asm-generic/pgtables.h changes]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de53e9caa4 upstream.
The Linux Kernel contains some inline assembly source code which has
wrong asm register constraints in arch/ia64/kvm/vtlb.c.
I observed this on Kernel 3.2.35 but it is also true on the most
recent Kernel 3.9-rc1.
File arch/ia64/kvm/vtlb.c:
u64 guest_vhpt_lookup(u64 iha, u64 *pte)
{
u64 ret;
struct thash_data *data;
data = __vtr_lookup(current_vcpu, iha, D_TLB);
if (data != NULL)
thash_vhpt_insert(current_vcpu, data->page_flags,
data->itir, iha, D_TLB);
asm volatile (
"rsm psr.ic|psr.i;;"
"srlz.d;;"
"ld8.s r9=[%1];;"
"tnat.nz p6,p7=r9;;"
"(p6) mov %0=1;"
"(p6) mov r9=r0;"
"(p7) extr.u r9=r9,0,53;;"
"(p7) mov %0=r0;"
"(p7) st8 [%2]=r9;;"
"ssm psr.ic;;"
"srlz.d;;"
"ssm psr.i;;"
"srlz.d;;"
: "=r"(ret) : "r"(iha), "r"(pte):"memory");
return ret;
}
The list of output registers is
: "=r"(ret) : "r"(iha), "r"(pte):"memory");
The constraint "=r" means that the GCC has to maintain that these vars
are in registers and contain valid info when the program flow leaves
the assembly block (output registers).
But "=r" also means that GCC can put them in registers that are used
as input registers. Input registers are iha, pte on the example.
If the predicate p7 is true, the 8th assembly instruction
"(p7) mov %0=r0;"
is the first one which writes to a register which is maintained by the
register constraints; it sets %0. %0 means the first register operand;
it is ret here.
This instruction might overwrite the %2 register (pte) which is needed
by the next instruction:
"(p7) st8 [%2]=r9;;"
Whether it really happens depends on how GCC decides what registers it
uses and how it optimizes the code.
The attached patch fixes the register operand constraints in
arch/ia64/kvm/vtlb.c.
The register constraints should be
: "=&r"(ret) : "r"(iha), "r"(pte):"memory");
The & means that GCC must not use any of the input registers to place
this output register in.
This is Debian bug#702639
(http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=702639).
The patch is applicable on Kernel 3.9-rc1, 3.2.35 and many other versions.
Signed-off-by: Stephan Schreiber <info@fs-driver.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e9dafd873 upstream.
Some cards on Ralink RT30xx chipset not have correctly TX_MIXER_GAIN
value in them EEPROM/EFUSE. In this case, we must use default value,
but always used EEPROM/EFUSE value. As result we have tranmitt power
range from -10dBm to +6dBm instead 0dBm to +16dBm.
Correctly value in EEPROM/EFUSE is one or more for RT3070 and two or
more for other RT30xx chips.
Tested on Canyon CNP-WF518N1 usb Wi-Fi dongle and Jorjin WN8020 usb
embedded Wi-Fi module.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 769ba7212f upstream.
Commit b51306c (PCI: Set device power state to PCI_D0 for device
without native PM support) modified pci_platform_power_transition()
by adding code causing dev->current_state for devices that don't
support native PCI PM but are power-manageable by the platform to be
changed to PCI_D0 regardless of the value returned by the preceding
platform_pci_set_power_state(). In particular, that also is done
if the platform_pci_set_power_state() has been successful, which
causes the correct power state of the device set by
pci_update_current_state() in that case to be overwritten by PCI_D0.
Fix that mistake by making the fallback to PCI_D0 only happen if
the platform_pci_set_power_state() has returned an error.
[bhelgaas: folded in Yinghai's simplification, added URL & stable info]
Reference: http://lkml.kernel.org/r/27806FC4E5928A408B78E88BBC67A2306F466BBA@ORSMSX101.amr.corp.intel.com
Reported-by: Chris J. Benenati <chris.j.benenati@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 545d6e189a upstream.
Found problem on system that firmware that could handle pci aer.
Firmware get error reporting after pci injecting error, before os boots.
But after os boots, firmware can not get report anymore, even pci=noaer
is passed.
Root cause: BIOS _OSC has problem with query bit checking.
It turns out that BIOS vendor is copying example code from ACPI Spec.
In ACPI Spec 5.0, page 290:
If (Not(And(CDW1,1))) // Query flag clear?
{ // Disable GPEs for features granted native control.
If (And(CTRL,0x01)) // Hot plug control granted?
{
Store(0,HPCE) // clear the hot plug SCI enable bit
Store(1,HPCS) // clear the hot plug SCI status bit
}
...
}
When Query flag is set, And(CDW1,1) will be 1, Not(1) will return 0xfffffffe.
So it will get into code path that should be for control set only.
BIOS acpi code should be changed to "If (LEqual(And(CDW1,1), 0)))"
Current kernel code is using _OSC query to notify firmware about support
from OS and then use _OSC to set control bits.
During query support, current code is using all possible controls.
So will execute code that should be only for control set stage.
That will have problem when pci=noaer or aer firmware_first is used.
As firmware have that control set for os aer already in query support stage,
but later will not os aer handling.
We should avoid passing all possible controls, just use osc_control_set
instead.
That should workaround BIOS bugs with affected systems on the field
as more bios vendors are copying sample code from ACPI spec.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d303e9e98f upstream.
Back 2010 during a revamp of the irq code some initializations
were moved from ia64_mca_init() to ia64_mca_late_init() in
commit c75f2aa13f
Cannot use register_percpu_irq() from ia64_mca_init()
But this was hideously wrong. First of all these initializations
are now down far too late. Specifically after all the other cpus
have been brought up and initialized their own CMC vectors from
smp_callin(). Also ia64_mca_late_init() may be called from any cpu
so the line:
ia64_mca_cmc_vector_setup(); /* Setup vector on BSP */
is generally not executed on the BSP, and so the CMC vector isn't
setup at all on that processor.
Make use of the arch_early_irq_init() hook to get this code executed
at just the right moment: not too early, not too late.
Reported-by: Fred Hartnett <fred.hartnett@hp.com>
Tested-by: Fred Hartnett <fred.hartnett@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7db5e7660 upstream.
The inode->i_mutex isn't hold when updating filp->f_pos
in read()/write(), so the filp->f_pos might be read as
0 or 1 in readdir() when there is concurrent read()/write()
on this same file, then may cause use after free in readdir().
The bug can be reproduced with Li Zefan's test code on the
link:
https://patchwork.kernel.org/patch/2160771/
This patch fixes the use after free under this situation.
Reported-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 288fa3e022 upstream.
As part of updating the vmbus protocol, the function hv_need_to_signal()
was introduced. This functions helps optimize signalling from guest to
host. The newly added memory barrier is needed to ensure that we correctly
decide when to signal the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Olaf Hering <olh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57ae1b0532 upstream.
Occurs when CONFIG_CRYPTO_CRC32C_INTEL=y and CONFIG_CRYPTO_CRC32C_INTEL=y.
Older versions of bintuils do not support the pclmulqdq instruction. The
PCLMULQDQ gas macro is used instead.
Signed-off-by: Sandy Wu <sandyw@twitter.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c39e8e4354 upstream.
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4df297129f upstream.
Currently, the depth reported in the stack tracer stack_trace file
does not match the stack_max_size file. This is because the stack_max_size
includes the overhead of stack tracer itself while the depth does not.
The first time a max is triggered, a calculation is not performed that
figures out the overhead of the stack tracer and subtracts it from
the stack_max_size variable. The overhead is stored and is subtracted
from the reported stack size for comparing for a new max.
Now the stack_max_size corresponds to the reported depth:
# cat stack_max_size
4640
# cat stack_trace
Depth Size Location (48 entries)
----- ---- --------
0) 4640 32 _raw_spin_lock+0x18/0x24
1) 4608 112 ____cache_alloc+0xb7/0x22d
2) 4496 80 kmem_cache_alloc+0x63/0x12f
3) 4416 16 mempool_alloc_slab+0x15/0x17
[...]
While testing against and older gcc on x86 that uses mcount instead
of fentry, I found that pasing in ip + MCOUNT_INSN_SIZE let the
stack trace show one more function deep which was missing before.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4ecbfc49b upstream.
When gcc 4.6 on x86 is used, the function tracer will use the new
option -mfentry which does a call to "fentry" at every function
instead of "mcount". The significance of this is that fentry is
called as the first operation of the function instead of the mcount
usage of being called after the stack.
This causes the stack tracer to show some bogus results for the size
of the last function traced, as well as showing "ftrace_call" instead
of the function. This is due to the stack frame not being set up
by the function that is about to be traced.
# cat stack_trace
Depth Size Location (48 entries)
----- ---- --------
0) 4824 216 ftrace_call+0x5/0x2f
1) 4608 112 ____cache_alloc+0xb7/0x22d
2) 4496 80 kmem_cache_alloc+0x63/0x12f
The 216 size for ftrace_call includes both the ftrace_call stack
(which includes the saving of registers it does), as well as the
stack size of the parent.
To fix this, if CC_USING_FENTRY is defined, then the stack_tracer
will reserve the first item in stack_dump_trace[] array when
calling save_stack_trace(), and it will fill it in with the parent ip.
Then the code will look for the parent pointer on the stack and
give the real size of the parent's stack pointer:
# cat stack_trace
Depth Size Location (14 entries)
----- ---- --------
0) 2640 48 update_group_power+0x26/0x187
1) 2592 224 update_sd_lb_stats+0x2a5/0x4ac
2) 2368 160 find_busiest_group+0x31/0x1f1
3) 2208 256 load_balance+0xd9/0x662
I'm Cc'ing stable, although it's not urgent, as it only shows bogus
size for item #0, the rest of the trace is legit. It should still be
corrected in previous stable releases.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87889501d0 upstream.
Use the stack of stack_trace_call() instead of check_stack() as
the test pointer for max stack size. It makes it a bit cleaner
and a little more accurate.
Adding stable, as a later fix depends on this patch.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0b885657b upstream.
We first tried to avoid updating atime/mtime entirely (commit
b0de59b573: "TTY: do not update atime/mtime on read/write"), and then
limited it to only update it occasionally (commit 37b7f3c765: "TTY:
fix atime/mtime regression"), but it turns out that this was both
insufficient and overkill.
It was insufficient because we let people attach to the shared ptmx node
to see activity without even reading atime/mtime, and it was overkill
because the "only once a minute" means that you can't really tell an
idle person from an active one with 'w'.
So this tries to fix the problem properly. It marks the shared ptmx
node as un-notifiable, and it lowers the "only once a minute" to a few
seconds instead - still long enough that you can't time individual
keystrokes, but short enough that you can tell whether somebody is
active or not.
Reported-by: Simon Kirby <sim@hostway.ca>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd4baaaa04 upstream.
An early draft of the PHC patch series included an alarm in the
gianfar driver. During the review process, the alarm code was dropped,
but the capability removal was overlooked. This patch fixes the issue
by advertising zero alarms.
This patch should be applied to every 3.x stable kernel.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Chris LaRocque <clarocq@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 104ad3b32d upstream.
ARM processors with LPAE enabled use 3 levels of page tables, with an
entry in the top level (pgd) covering 1GB of virtual space. Because of
the branch relocation limitations on ARM, the loadable modules are
mapped 16MB below PAGE_OFFSET, making the corresponding 1GB pgd shared
between kernel modules and user space.
If free_pgtables() is called with the default ceiling 0,
free_pgd_range() (and subsequently called functions) also frees the page
table shared between user space and kernel modules (which is normally
handled by the ARM-specific pgd_free() function). This patch changes
defines the ARM USER_PGTABLES_CEILING to TASK_SIZE when CONFIG_ARM_LPAE
is enabled.
Note that the pgd_free() function already checks the presence of the
shared pmd page allocated by pgd_alloc() and frees it, though with
ceiling 0 this wasn't necessary.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a65dcc04c upstream.
The serial core uses device_find_child() but does not drop the reference to
the retrieved child after using it. This patch add the missing put_device().
What I have done to test this issue.
I used a machine with an AMBA PL011 serial driver. I tested the patch on
next-20120408 because the last branch [next-20120415] does not boot on this
board.
For test purpose, I added some pr_info() messages to print the refcount
after device_find_child() (lines: 1937,2009), and after put_device()
(lines: 1947, 2021).
Boot the machine *without* put_device(). Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 87.058575] uart_suspend_port:1937 refcount 4
[ 87.058582] uart_suspend_port:1947 refcount 4
[ 87.098083] uart_resume_port:2009refcount 5
[ 87.098088] uart_resume_port:2021 refcount 5
echo disk > /sys/power/state
[ 103.055574] uart_suspend_port:1937 refcount 6
[ 103.055580] uart_suspend_port:1947 refcount 6
[ 103.095322] uart_resume_port:2009 refcount 7
[ 103.095327] uart_resume_port:2021 refcount 7
echo disk > /sys/power/state
[ 252.459580] uart_suspend_port:1937 refcount 8
[ 252.459586] uart_suspend_port:1947 refcount 8
[ 252.499611] uart_resume_port:2009 refcount 9
[ 252.499616] uart_resume_port:2021 refcount 9
The refcount continuously increased.
Boot the machine *with* this patch. Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 159.333559] uart_suspend_port:1937 refcount 4
[ 159.333566] uart_suspend_port:1947 refcount 3
[ 159.372751] uart_resume_port:2009 refcount 4
[ 159.372755] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 185.713614] uart_suspend_port:1937 refcount 4
[ 185.713621] uart_suspend_port:1947 refcount 3
[ 185.752935] uart_resume_port:2009 refcount 4
[ 185.752940] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 207.458584] uart_suspend_port:1937 refcount 4
[ 207.458591] uart_suspend_port:1947 refcount 3
[ 207.498598] uart_resume_port:2009 refcount 4
[ 207.498605] uart_resume_port:2021 refcount 3
The refcount correctly handled.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66ff0fe9e7 upstream.
While we don't use the spinlock interrupt line (see for details
commit f10cd522c5 -
xen: disable PV spinlocks on HVM) - we should still do the proper
init / deinit sequence. We did not do that correctly and for the
CPU init for PVHVM guest we would allocate an interrupt line - but
failed to deallocate the old interrupt line.
This resulted in leakage of an irq_desc but more importantly this splat
as we online an offlined CPU:
genirq: Flags mismatch irq 71. 0002cc20 (spinlock1) vs. 0002cc20 (spinlock1)
Pid: 2542, comm: init.late Not tainted 3.9.0-rc6upstream #1
Call Trace:
[<ffffffff811156de>] __setup_irq+0x23e/0x4a0
[<ffffffff81194191>] ? kmem_cache_alloc_trace+0x221/0x250
[<ffffffff811161bb>] request_threaded_irq+0xfb/0x160
[<ffffffff8104c6f0>] ? xen_spin_trylock+0x20/0x20
[<ffffffff813a8423>] bind_ipi_to_irqhandler+0xa3/0x160
[<ffffffff81303758>] ? kasprintf+0x38/0x40
[<ffffffff8104c6f0>] ? xen_spin_trylock+0x20/0x20
[<ffffffff810cad35>] ? update_max_interval+0x15/0x40
[<ffffffff816605db>] xen_init_lock_cpu+0x3c/0x78
[<ffffffff81660029>] xen_hvm_cpu_notify+0x29/0x33
[<ffffffff81676bdd>] notifier_call_chain+0x4d/0x70
[<ffffffff810bb2a9>] __raw_notifier_call_chain+0x9/0x10
[<ffffffff8109402b>] __cpu_notify+0x1b/0x30
[<ffffffff8166834a>] _cpu_up+0xa0/0x14b
[<ffffffff816684ce>] cpu_up+0xd9/0xec
[<ffffffff8165f754>] store_online+0x94/0xd0
[<ffffffff8141d15b>] dev_attr_store+0x1b/0x20
[<ffffffff81218f44>] sysfs_write_file+0xf4/0x170
[<ffffffff811a2864>] vfs_write+0xb4/0x130
[<ffffffff811a302a>] sys_write+0x5a/0xa0
[<ffffffff8167ada9>] system_call_fastpath+0x16/0x1b
cpu 1 spinlock event irq -16
smpboot: Booting Node 0 Processor 1 APIC 0x2
And if one looks at the /proc/interrupts right after
offlining (CPU1):
70: 0 0 xen-percpu-ipi spinlock0
71: 0 0 xen-percpu-ipi spinlock1
77: 0 0 xen-percpu-ipi spinlock2
There is the oddity of the 'spinlock1' still being present.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 888b65b4bc upstream.
In the PVHVM path when we do CPU online/offline path we would
leak the timer%d IRQ line everytime we do a offline event. The
online path (xen_hvm_setup_cpu_clockevents via
x86_cpuinit.setup_percpu_clockev) would allocate a new interrupt
line for the timer%d.
But we would still use the old interrupt line leading to:
kernel BUG at /home/konrad/ssd/konrad/linux/kernel/hrtimer.c:1261!
invalid opcode: 0000 [#1] SMP
RIP: 0010:[<ffffffff810b9e21>] [<ffffffff810b9e21>] hrtimer_interrupt+0x261/0x270
.. snip..
<IRQ>
[<ffffffff810445ef>] xen_timer_interrupt+0x2f/0x1b0
[<ffffffff81104825>] ? stop_machine_cpu_stop+0xb5/0xf0
[<ffffffff8111434c>] handle_irq_event_percpu+0x7c/0x240
[<ffffffff811175b9>] handle_percpu_irq+0x49/0x70
[<ffffffff813a74a3>] __xen_evtchn_do_upcall+0x1c3/0x2f0
[<ffffffff813a760a>] xen_evtchn_do_upcall+0x2a/0x40
[<ffffffff8167c26d>] xen_hvm_callback_vector+0x6d/0x80
<EOI>
[<ffffffff81666d01>] ? start_secondary+0x193/0x1a8
[<ffffffff81666cfd>] ? start_secondary+0x18f/0x1a8
There is also the oddity (timer1) in the /proc/interrupts after
offlining CPU1:
64: 1121 0 xen-percpu-virq timer0
78: 0 0 xen-percpu-virq timer1
84: 0 2483 xen-percpu-virq timer2
This patch fixes it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7918c92ae9 upstream.
When we online the CPU, we get this splat:
smpboot: Booting Node 0 Processor 1 APIC 0x2
installing Xen timer for CPU 1
BUG: sleeping function called from invalid context at /home/konrad/ssd/konrad/linux/mm/slab.c:3179
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/1
Pid: 0, comm: swapper/1 Not tainted 3.9.0-rc6upstream-00001-g3884fad #1
Call Trace:
[<ffffffff810c1fea>] __might_sleep+0xda/0x100
[<ffffffff81194617>] __kmalloc_track_caller+0x1e7/0x2c0
[<ffffffff81303758>] ? kasprintf+0x38/0x40
[<ffffffff813036eb>] kvasprintf+0x5b/0x90
[<ffffffff81303758>] kasprintf+0x38/0x40
[<ffffffff81044510>] xen_setup_timer+0x30/0xb0
[<ffffffff810445af>] xen_hvm_setup_cpu_clockevents+0x1f/0x30
[<ffffffff81666d0a>] start_secondary+0x19c/0x1a8
The solution to that is use kasprintf in the CPU hotplug path
that 'online's the CPU. That is, do it in in xen_hvm_cpu_notify,
and remove the call to in xen_hvm_setup_cpu_clockevents.
Unfortunatly the later is not a good idea as the bootup path
does not use xen_hvm_cpu_notify so we would end up never allocating
timer%d interrupt lines when booting. As such add the check for
atomic() to continue.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94c163663f upstream.
In case a machine supports memory hotplug all active memory increments
present at IPL time have been initialized with a "usecount" of 1.
This is wrong if the memory increment size is larger than the memory
section size of the memory hotplug code. If that is the case the
usecount must be initialized with the number of memory sections that
fit into one memory increment.
Otherwise it is possible to put a memory increment into standby state
even if there are still active sections.
Afterwards addressing exceptions might happen which cause the kernel
to panic.
However even worse, if a memory increment was put into standby state
and afterwards into active state again, it's contents would have been
zeroed, leading to memory corruption.
This was only an issue for machines that support standby memory and
have at least 256GB memory.
This is broken since commit fdb1bb15 "[S390] sclp/memory hotplug: fix
initial usecount of increments".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 671b4b2ba9 upstream.
Many cards based on CY7C68300A/B/C use the USB ID 04b4:6830 but only the
B and C variants (EZ-USB AT2LP) support the ATA Command Block
functionality, according to the data sheets. The A variant (EZ-USB AT2)
locks up if ATACB is attempted, until a typical 30 seconds timeout runs
out and a USB reset is performed.
https://bugs.launchpad.net/bugs/428469
It seems that one way to spot a CY7C68300A (at least where the card
manufacturer left Cypress' EEPROM default vaules, against Cypress'
recommendations) is to look at the USB string descriptor indices.
A http://media.digikey.com/pdf/Data%20Sheets/Cypress%20PDFs/CY7C68300A.pdf
B http://www.farnell.com/datasheets/43456.pdf
C http://www.cypress.com/?rID=14189
Note that a CY7C68300B/C chip appears as CY7C68300A if it is running
in Backward Compatibility Mode, and if ATACB would be supported in this
case there is anyway no way to tell which chip it really is.
For 5 years my external USB drive has been locking up for half a minute
when plugged in and ata_id is run by udev, or anytime hdparm or similar
is run on it.
Finally looking at the /correct/ datasheet I think I found the reason. I
am aware the quirk in this patch is a bit hacky, but the hardware
manufacturers haven't made it easy for us.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ca2cd291f upstream.
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c174302b upstream.
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
writeb(0xde, &td->ptr.next + 0x0); /* strb */
writeb(0xad, &td->ptr.next + 0x1); /* strb */
<----- hardware reads value of td->ptr.next and get stuck!
writeb(0xbe, &td->ptr.next + 0x2); /* strb */
writeb(0xef, &td->ptr.next + 0x3); /* strb */
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1361bf4b9f upstream.
When usbfs receives a ctrl-request from userspace it calls check_ctrlrecip,
which for a request with USB_RECIP_ENDPOINT tries to map this to an interface
to see if this interface is claimed, except for ctrl-requests with a type of
USB_TYPE_VENDOR.
When trying to use this device: http://www.akaipro.com/eiepro
redirected to a Windows vm running on qemu on top of Linux.
The windows driver makes a ctrl-req with USB_TYPE_CLASS and
USB_RECIP_ENDPOINT with index 0, and the mapping of the endpoint (0) to
the interface fails since ep 0 is the ctrl endpoint and thus never is
part of an interface.
This patch fixes this ctrl-req failing by skipping the checkintf call for
USB_RECIP_ENDPOINT ctrl-reqs on the ctrl endpoint.
Reported-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Tested-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6fd35ee57 upstream.
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71d9a2b95f upstream.
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.
We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f06d15f8d upstream.
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58f8b6c4fa upstream.
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ceb59557b upstream.
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b20d34c458 upstream.
Since Stanislaw's patches, when suspending while connected,
cfg80211 will disconnect. This causes the AP station to be
removed, which uses call_rcu() to clean up. Due to needing
process context, this queues a work struct on the mac80211
workqueue. This will warn and fail when already suspended,
which can happen if the rcu call doesn't happen quickly.
To fix this, replace the synchronize_net() which is really
just synchronize_rcu_expedited() with rcu_barrier(), which
unlike synchronize_rcu() waits until RCU callback have run
and thus avoids this issue.
In theory, this can even happen without Stanislaw's change
to disconnect on suspend since userspace might disconnect
just before suspending, though then it's unlikely that the
call_rcu() will be delayed long enough.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63b77bf489 upstream.
When the stations are being restored because of unassoc
RXON, the LQ cmd may not have been initialized because it
is initialized only after association.
Sending zeroed LQ_CMD makes the fw unhappy: it raises
SYSASSERT_2078.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[move zero_lq and make static const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6747e83235 upstream.
In commit 85fe402 (fs: do not assign default i_ino in new_inode), the
initialisation of i_ino was removed from new_inode() and pushed down
into the callers. However spufs_new_inode() was not updated.
This exhibits as no files appearing in /spu, because all our dirents
have a zero inode, which readdir() seems to dislike.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c2a381734 upstream.
In __restore_cpu_power8 we determine if we are HV and if not, we return
before setting HV only resources.
Unfortunately we forgot to restore the link register from r11 before
returning.
This will happen on boot and with secondary CPUs not coming online.
This adds the missing link register restore.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e96ca7f00 upstream.
POWER8 allows us to take interrupts with the MMU on. This gives us a
second set of vectors offset at 0x4000.
Unfortunately when coping these vectors we missed checking for MSR HV
for hardware interrupts (0x500). This results in us trying to use
HSRR0/1 when HV=0, rather than SRR0/1 on HW IRQs
The below fixes this to check CPU_FTR_HVMODE when patching the code at
0x4500.
Also we remove the check for CPU_FTR_ARCH_206 since relocation on IRQs
are only available in arch 2.07 and beyond.
Thanks to benh for helping find this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29ce3c5073 upstream.
In __after_prom_start we copy the kernel down to zero in two calls to
copy_and_flush. After the first call (copy from 0 to copy_to_here:)
we jump to the newly copied code soon after.
Unfortunately there's no isync between the copy of this code and the
jump to it. Hence it's possible that stale instructions could still be
in the icache or pipeline before we branch to it.
We've seen this on real machines and it's results in no console output
after:
calling quiesce...
returning from prom_init
The below adds an isync to ensure that the copy and flushing has
completed before any branching to the new instructions occurs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d97558901 upstream.
The TIME_VALID flag is specified for the different states but
the time residency computation is not done, no tk flag, no time
computation in the idle function.
Set the en_core_tk_irqen flag to activate it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d95abbbb29 upstream.
Testing the arm chromebook config against the upstream
kernel produces a linker error for the zsmalloc module from
staging. The symbol flush_tlb_kernel_range is not available
there. Fix this by removing the reimplementation of
unmap_kernel_range in the zsmalloc module and using the
function directly. The unmap_kernel_range function is not
usable by modules, so also disallow building the driver as a
module for now.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
<listitem><para><constant>FE_SCALE_NOT_AVAILABLE</constant> - The parameter is supported by the frontend, but it was not possible to collect it (could be a transitory or permanent condition)</para></listitem>
<listitem><para><constant>FE_SCALE_DECIBEL</constant> - parameter is a signed value, measured in 1/1000 dB</para></listitem>
<listitem><para><constant>FE_SCALE_RELATIVE</constant> - parameter is a unsigned value, where 0 means 0% and 65535 means 100%.</para></listitem>
<listitem><para><constant>FE_SCALE_COUNTER</constant> - parameter is a unsigned value that counts the occurrence of an event, like bit error, block error, or lapsed time.</para></listitem>
</itemizedlist>
</section>
</listitem>
</itemizedlist>
<sectionid="DTV-STAT-SIGNAL-STRENGTH">
@ -916,9 +918,9 @@ enum fe_interleaving {
<para>Indicates the signal strength level at the analog part of the tuner or of the demod.</para>
<para>Possible scales for this metric are:</para>
<itemizedlistmark='bullet'>
<listitem><para><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</para></listitem>
<listitem><para><constant>FE_SCALE_DECIBEL</constant> - signal strength is in 0.0001 dBm units, power measured in miliwatts. This value is generally negative.</para></listitem>
<listitem><para><constant>FE_SCALE_RELATIVE</constant> - The frontend provides a 0% to 100% measurement for power (actually, 0 to 65535).</para></listitem>
<listitem><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</listitem>
<listitem><constant>FE_SCALE_DECIBEL</constant> - signal strength is in 0.0001 dBm units, power measured in miliwatts. This value is generally negative.</listitem>
<listitem><constant>FE_SCALE_RELATIVE</constant> - The frontend provides a 0% to 100% measurement for power (actually, 0 to 65535).</listitem>
</itemizedlist>
</section>
<sectionid="DTV-STAT-CNR">
@ -926,9 +928,9 @@ enum fe_interleaving {
<para>Indicates the Signal to Noise ratio for the main carrier.</para>
<para>Possible scales for this metric are:</para>
<itemizedlistmark='bullet'>
<listitem><para><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</para></listitem>
<listitem><para><constant>FE_SCALE_DECIBEL</constant> - Signal/Noise ratio is in 0.0001 dB units.</para></listitem>
<listitem><para><constant>FE_SCALE_RELATIVE</constant> - The frontend provides a 0% to 100% measurement for Signal/Noise (actually, 0 to 65535).</para></listitem>
<listitem><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</listitem>
<listitem><constant>FE_SCALE_DECIBEL</constant> - Signal/Noise ratio is in 0.0001 dB units.</listitem>
<listitem><constant>FE_SCALE_RELATIVE</constant> - The frontend provides a 0% to 100% measurement for Signal/Noise (actually, 0 to 65535).</listitem>
</itemizedlist>
</section>
<sectionid="DTV-STAT-PRE-ERROR-BIT-COUNT">
@ -941,8 +943,8 @@ enum fe_interleaving {
The frontend may reset it when a channel/transponder is tuned.</para>
<para>Possible scales for this metric are:</para>
<itemizedlistmark='bullet'>
<listitem><para><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</para></listitem>
<listitem><para><constant>FE_SCALE_COUNTER</constant> - Number of error bits counted before the inner coding.</para></listitem>
<listitem><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</listitem>
<listitem><constant>FE_SCALE_COUNTER</constant> - Number of error bits counted before the inner coding.</listitem>
</itemizedlist>
</section>
<sectionid="DTV-STAT-PRE-TOTAL-BIT-COUNT">
@ -950,14 +952,14 @@ enum fe_interleaving {
<para>Measures the amount of bits received before the inner code block, during the same period as
<linklinkend="DTV-STAT-PRE-ERROR-BIT-COUNT"><constant>DTV_STAT_PRE_ERROR_BIT_COUNT</constant></link> measurement was taken.</para>
<para>It should be noticed that this measurement can be smaller than the total amount of bits on the transport stream,
as the frontend may need to manually restart the measurement, losing some data between each measurement interval.</para>
as the frontend may need to manually restart the measurement, loosing some data between each measurement interval.</para>
<para>This measurement is monotonically increased, as the frontend gets more bit count measurements.
The frontend may reset it when a channel/transponder is tuned.</para>
<para>Possible scales for this metric are:</para>
<itemizedlistmark='bullet'>
<listitem><para><constant>FE_SCALE_NOT_AVAILABLE</constant> - it failed to measure it, or the measurement was not complete yet.</para></listitem>
<listitem><para><constant>FE_SCALE_COUNTER</constant> - Number of bits counted while measuring
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
