commit 7c8c0291f8 upstream.
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[fixes gcc-11 build warnings - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff4cff962a ]
board-xxs1500.c references 2 functions without declaring them, so add
the header file to placate the build.
../arch/mips/alchemy/board-xxs1500.c: In function 'board_setup':
../arch/mips/alchemy/board-xxs1500.c:56:2: error: implicit declaration of function 'alchemy_gpio1_input_enable' [-Werror=implicit-function-declaration]
56 | alchemy_gpio1_input_enable();
../arch/mips/alchemy/board-xxs1500.c:57:2: error: implicit declaration of function 'alchemy_gpio2_enable'; did you mean 'alchemy_uart_enable'? [-Werror=implicit-function-declaration]
57 | alchemy_gpio2_enable();
Fixes: 8e026910fc ("MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e29f011e8f ]
Commit dbd1759e6a ("ipv6: on reassembly, record frag_max_size")
filled the frag_max_size field in IP6CB in the input path.
The field should also be filled in case of atomic fragments.
Fixes: dbd1759e6a ('ipv6: on reassembly, record frag_max_size')
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84316ca4e1 ]
The skb_change_head() helper did not set "skb->mac_len", which is
problematic when it's used in combination with skb_redirect_peer().
Without it, redirecting a packet from a L3 device such as wireguard to
the veth peer device will cause skb->data to point to the middle of the
IP header on entry to tcp_v4_rcv() since the L2 header is not pulled
correctly due to mac_len=0.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210519154743.2554771-2-joamaki@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020ef930b8 ]
mld_newpack() doesn't allow to allocate high order page,
only order-0 allocation is allowed.
If headroom size is too large, a kernel panic could occur in skb_put().
Test commands:
ip netns del A
ip netns del B
ip netns add A
ip netns add B
ip link add veth0 type veth peer name veth1
ip link set veth0 netns A
ip link set veth1 netns B
ip netns exec A ip link set lo up
ip netns exec A ip link set veth0 up
ip netns exec A ip -6 a a 2001:db8:0::1/64 dev veth0
ip netns exec B ip link set lo up
ip netns exec B ip link set veth1 up
ip netns exec B ip -6 a a 2001:db8:0::2/64 dev veth1
for i in {1..99}
do
let A=$i-1
ip netns exec A ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::1 remote 2001:db8:$A::2 encaplimit 100
ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev ip6gre$i
ip netns exec A ip link set ip6gre$i up
ip netns exec B ip link add ip6gre$i type ip6gre \
local 2001:db8:$A::2 remote 2001:db8:$A::1 encaplimit 100
ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev ip6gre$i
ip netns exec B ip link set ip6gre$i up
done
Splat looks like:
kernel BUG at net/core/skbuff.c:110!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.12.0+ #891
Workqueue: ipv6_addrconf addrconf_dad_work
RIP: 0010:skb_panic+0x15d/0x15f
Code: 92 fe 4c 8b 4c 24 10 53 8b 4d 70 45 89 e0 48 c7 c7 00 ae 79 83
41 57 41 56 41 55 48 8b 54 24 a6 26 f9 ff <0f> 0b 48 8b 6c 24 20 89
34 24 e8 4a 4e 92 fe 8b 34 24 48 c7 c1 20
RSP: 0018:ffff88810091f820 EFLAGS: 00010282
RAX: 0000000000000089 RBX: ffff8881086e9000 RCX: 0000000000000000
RDX: 0000000000000089 RSI: 0000000000000008 RDI: ffffed1020123efb
RBP: ffff888005f6eac0 R08: ffffed1022fc0031 R09: ffffed1022fc0031
R10: ffff888117e00187 R11: ffffed1022fc0030 R12: 0000000000000028
R13: ffff888008284eb0 R14: 0000000000000ed8 R15: 0000000000000ec0
FS: 0000000000000000(0000) GS:ffff888117c00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8b801c5640 CR3: 0000000033c2c006 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
skb_put.cold.104+0x22/0x22
ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
? rcu_read_lock_sched_held+0x91/0xc0
mld_newpack+0x398/0x8f0
? ip6_mc_hdr.isra.26.constprop.46+0x600/0x600
? lock_contended+0xc40/0xc40
add_grhead.isra.33+0x280/0x380
add_grec+0x5ca/0xff0
? mld_sendpack+0xf40/0xf40
? lock_downgrade+0x690/0x690
mld_send_initial_cr.part.34+0xb9/0x180
ipv6_mc_dad_complete+0x15d/0x1b0
addrconf_dad_completed+0x8d2/0xbb0
? lock_downgrade+0x690/0x690
? addrconf_rs_timer+0x660/0x660
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
Allowing high order page allocation could fix this problem.
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1d027dd97 ]
'bus->mii_bus' has been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the error handling path of the
probe function and in remove function.
Suggested-By: Andrew Lunn <andrew@lunn.ch>
Fixes: 35d2aeac98 ("phy: mdio-octeon: Use devm_mdiobus_alloc_size()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93a0a1587 ]
'bus->mii_bus' have been allocated with 'devm_mdiobus_alloc_size()' in the
probe function. So it must not be freed explicitly or there will be a
double free.
Remove the incorrect 'mdiobus_free' in the remove function.
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddb6e00f84 ]
'ret' is known to be 0 here.
The expected error code is stored in 'tx_pipe->dma_queue', so use it
instead.
While at it, switch from %d to %pe which is more user friendly.
Fixes: 84640e27f2 ("net: netcp: Add Keystone NetCP core ethernet driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0d46717b9 ]
See MS-SMB2 3.2.4.1.4, file ids in compounded requests should be set to
0xFFFFFFFFFFFFFFFF (we were treating it as u32 not u64 and setting
it incorrectly).
Signed-off-by: Steve French <stfrench@microsoft.com>
Reported-by: Stefan Metzmacher <metze@samba.org>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b549c18ae ]
This came up in the discussion of the requirements of qspinlock on an
architecture. OpenRISC uses qspinlock, but it was noticed that the
memmory barrier was not defined.
Peter defined it in the mail thread writing:
As near as I can tell this should do. The arch spec only lists
this one instruction and the text makes it sound like a completion
barrier.
This is correct so applying this patch.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
[shorne@gmail.com:Turned the mail into a patch]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56f396146a ]
Commit 391e2f2560 ("[SCSI] BusLogic: Port driver to 64-bit")
introduced a serious issue for 64-bit systems. With this commit,
64-bit kernel will enumerate 8*15 non-existing disks. This is caused
by the broken CCB structure. The change from u32 data to void *data
increased CCB length on 64-bit system, which introduced an extra 4
byte offset of the CDB. This leads to incorrect response to INQUIRY
commands during enumeration.
Fix disk enumeration failure by reverting the portion of the commit
above which switched the data pointer from u32 to void.
Link: https://lore.kernel.org/r/C325637F-1166-4340-8F0F-3BCCD59D4D54@vmware.com
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Matt Wang <wwentao@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e79b38fe9 ]
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-54-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c446f0d470 ]
Move hw->cfg.mode and hw->addr.mode assignments from hw->ci->cfg_mode
and hw->ci->addr_mode respectively, to be before the subsequent checks
for memory IO mode (and possible ioremap calls in this case).
Also introduce ioremap error checks at both locations. This allows
resources to be properly freed on ioremap failure, as when the caller
of setup_io then subsequently calls release_io via its error path,
release_io can now correctly determine the mode as it has been set
before the ioremap call.
Finally, refactor release_io function so that it will call
release_mem_region in the memory IO case, regardless of whether or not
hw->cfg.p/hw->addr.p are NULL. This means resources are then properly
released on failure.
This properly implements the original reverted commit (d721fe99f6)
from the University of Minnesota, whilst also implementing the ioremap
check for the hw->ci->cfg_mode if block as well.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210503115736.2104747-42-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65a67792e3 ]
The condition of dev == NULL is impossible in caif_xmit(), hence it is
for the removal.
Explanation:
The static caif_xmit() is only called upon via a function pointer
`ndo_start_xmit` defined in include/linux/netdevice.h:
```
struct net_device_ops {
...
netdev_tx_t (*ndo_start_xmit)(struct sk_buff *skb, struct net_device *dev);
...
}
```
The exhausive list of call points are:
```
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c
dev->netdev_ops->ndo_start_xmit(skb, dev);
^ ^
drivers/infiniband/ulp/opa_vnic/opa_vnic_netdev.c
struct opa_vnic_adapter *adapter = opa_vnic_priv(netdev);
^ ^
return adapter->rn_ops->ndo_start_xmit(skb, netdev); // adapter would crash first
^ ^
drivers/usb/gadget/function/f_ncm.c
ncm->netdev->netdev_ops->ndo_start_xmit(NULL, ncm->netdev);
^ ^
include/linux/netdevice.h
static inline netdev_tx_t __netdev_start_xmit(...
{
return ops->ndo_start_xmit(skb, dev);
^
}
const struct net_device_ops *ops = dev->netdev_ops;
^
rc = __netdev_start_xmit(ops, skb, dev, more);
^
```
In each of the enumerated scenarios, it is impossible for the NULL-valued dev to
reach the caif_xmit() without crashing the kernel earlier, therefore `BUG_ON(dev ==
NULL)` is rather useless, hence the removal.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-20-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3890e3dea3 ]
The macro "spi_register_driver" invokes the function
"__spi_register_driver()" which has a return type of int and can fail,
returning a negative value in such a case. This is currently ignored and
the init() function yields success even if the spi driver failed to
register.
Fix this by collecting the return value of "__spi_register_driver()" and
also unregister the uart driver in case of failure.
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2499042326 upstream.
Interrupt handler processes multiple message write requests one after
another, till the driver message queue is drained. However if driver
encounters a read message without preceding START, it stops the I2C
transfer as it is an invalid condition for the controller. At least the
comment describes a requirement "the controller forces us to send a new
START when we change direction". This stop results in clearing the
message queue (i2c->msg = NULL).
The code however immediately jumped back to label "retry_write" which
dereferenced the "i2c->msg" making it a possible NULL pointer
dereference.
The Coverity analysis:
1. Condition !is_msgend(i2c), taking false branch.
if (!is_msgend(i2c)) {
2. Condition !is_lastmsg(i2c), taking true branch.
} else if (!is_lastmsg(i2c)) {
3. Condition i2c->msg->flags & 1, taking true branch.
if (i2c->msg->flags & I2C_M_RD) {
4. write_zero_model: Passing i2c to s3c24xx_i2c_stop, which sets i2c->msg to NULL.
s3c24xx_i2c_stop(i2c, -EINVAL);
5. Jumping to label retry_write.
goto retry_write;
6. var_deref_model: Passing i2c to is_msgend, which dereferences null i2c->msg.
if (!is_msgend(i2c)) {"
All previous calls to s3c24xx_i2c_stop() in this interrupt service
routine are followed by jumping to end of function (acknowledging
the interrupt and returning). This seems a reasonable choice also here
since message buffer was entirely emptied.
Addresses-Coverity: Explicit null dereferenced
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7df21cf1b upstream.
It's not a good idea to append the frag skb to a skb's frag_list if
the frag_list already has skbs from elsewhere, such as this skb was
created by pskb_copy() where the frag_list was cloned (all the skbs
in it were skb_get'ed) and shared by multiple skbs.
However, the new appended frag skb should have been only seen by the
current skb. Otherwise, it will cause use after free crashes as this
appended frag skb are seen by multiple skbs but it only got skb_get
called once.
The same thing happens with a skb updated by pskb_may_pull() with a
skb_cloned skb. Li Shuang has reported quite a few crashes caused
by this when doing testing over macvlan devices:
[] kernel BUG at net/core/skbuff.c:1970!
[] Call Trace:
[] skb_clone+0x4d/0xb0
[] macvlan_broadcast+0xd8/0x160 [macvlan]
[] macvlan_process_broadcast+0x148/0x150 [macvlan]
[] process_one_work+0x1a7/0x360
[] worker_thread+0x30/0x390
[] kernel BUG at mm/usercopy.c:102!
[] Call Trace:
[] __check_heap_object+0xd3/0x100
[] __check_object_size+0xff/0x16b
[] simple_copy_to_iter+0x1c/0x30
[] __skb_datagram_iter+0x7d/0x310
[] __skb_datagram_iter+0x2a5/0x310
[] skb_copy_datagram_iter+0x3b/0x90
[] tipc_recvmsg+0x14a/0x3a0 [tipc]
[] ____sys_recvmsg+0x91/0x150
[] ___sys_recvmsg+0x7b/0xc0
[] kernel BUG at mm/slub.c:305!
[] Call Trace:
[] <IRQ>
[] kmem_cache_free+0x3ff/0x400
[] __netif_receive_skb_core+0x12c/0xc40
[] ? kmem_cache_alloc+0x12e/0x270
[] netif_receive_skb_internal+0x3d/0xb0
[] ? get_rx_page_info+0x8e/0xa0 [be2net]
[] be_poll+0x6ef/0xd00 [be2net]
[] ? irq_exit+0x4f/0x100
[] net_rx_action+0x149/0x3b0
...
This patch is to fix it by linearizing the head skb if it has frag_list
set in tipc_buf_append(). Note that we choose to do this before calling
skb_unshare(), as __skb_linearize() will avoid skb_copy(). Also, we can
not just drop the frag_list either as the early time.
Fixes: 45c8b7b175 ("tipc: allow non-linear first fragment buffer")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db825feefc upstream.
Fix SFP and QSFP* EEPROM queries by setting i2c_address, offset and page
number correctly. For SFP set the following params:
- I2C address for offsets 0-255 is 0x50. For 256-511 - 0x51.
- Page number is zero.
- Offset is 0-255.
At the same time, QSFP* parameters are different:
- I2C address is always 0x50.
- Page number is not limited to zero.
- Offset is 0-255 for page zero and 128-255 for others.
To set parameters accordingly to cable used, implement function to query
module ID and implement respective helper functions to set parameters
correctly.
Fixes: 135dd9594f ("net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cfc4ea78f upstream.
When main component is not probed, by example when the dw-hdmi module is
not loaded yet or in probe defer, the following crash appears on shutdown:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038
...
pc : meson_drv_shutdown+0x24/0x50
lr : platform_drv_shutdown+0x20/0x30
...
Call trace:
meson_drv_shutdown+0x24/0x50
platform_drv_shutdown+0x20/0x30
device_shutdown+0x158/0x360
kernel_restart_prepare+0x38/0x48
kernel_restart+0x18/0x68
__do_sys_reboot+0x224/0x250
__arm64_sys_reboot+0x24/0x30
...
Simply check if the priv struct has been allocated before using it.
Fixes: fa0c16caf3 ("drm: meson_drv add shutdown function")
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430082744.3638743-1-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e67afa7ee4 upstream.
Since commit bdcc2cd14e ("NFSv4.2: handle NFS-specific llseek errors"),
nfs42_proc_llseek would return -EOPNOTSUPP rather than -ENOTSUPP when
SEEK_DATA on NFSv4.0/v4.1.
This will lead xfstests generic/285 not run on NFSv4.0/v4.1 when set the
CONFIG_NFS_V4_2, rather than run failed.
Fixes: bdcc2cd14e ("NFSv4.2: handle NFS-specific llseek errors")
Cc: <stable.vger.kernel.org> # 4.2
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d0ea30935 upstream.
The value of mirror->pg_bytes_written should only be updated after a
successful attempt to flush out the requests on the list.
Fixes: a7d42ddb30 ("nfs: add mirroring support to pgio layer")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 769b01ea68 upstream.
The "sizeof(struct nfs_fh)" is two bytes too large and could lead to
memory corruption. It should be NFS_MAXFHSIZE because that's the size
of the ->data[] buffer.
I reversed the size of the arguments to put the variable on the left.
Fixes: 16b374ca43 ("NFSv4.1: pnfs: filelayout: add driver's LAYOUTGET and GETDEVICEINFO infrastructure")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8da3a0b87f4f1c3a3bbc4bfb78cf68476e97d183 upstream.
When cmtp_attach_device fails, cmtp_add_connection returns the error value
which leads to the caller to doing fput through sockfd_put. But
cmtp_session kthread, which is stopped in this path will also call fput,
leading to a potential refcount underflow or a use-after-free.
Add a refcount before we signal the kthread to stop. The kthread will try
to grab the cmtp_session_sem mutex before doing the fput, which is held
when get_file is called, so there should be no races there.
Reported-by: Ryota Shiga
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46a8b29c63 upstream.
Syzbot reported memory leak in smsc75xx_bind().
The problem was is non-freed memory in case of
errors after memory allocation.
backtrace:
[<ffffffff84245b62>] kmalloc include/linux/slab.h:556 [inline]
[<ffffffff84245b62>] kzalloc include/linux/slab.h:686 [inline]
[<ffffffff84245b62>] smsc75xx_bind+0x7a/0x334 drivers/net/usb/smsc75xx.c:1460
[<ffffffff82b5b2e6>] usbnet_probe+0x3b6/0xc30 drivers/net/usb/usbnet.c:1728
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Cc: stable@kernel.vger.org
Reported-and-tested-by: syzbot+b558506ba8165425fee2@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e752dbc59e upstream.
The usb3_start_pipen() is called by renesas_usb3_ep_queue() and
usb3_request_done_pipen() so that usb3_start_pipen() is possible
to cause a race when getting usb3_first_req like below:
renesas_usb3_ep_queue()
spin_lock_irqsave()
list_add_tail()
spin_unlock_irqrestore()
usb3_start_pipen()
usb3_first_req = usb3_get_request() --- [1]
--- interrupt ---
usb3_irq_dma_int()
usb3_request_done_pipen()
usb3_get_request()
usb3_start_pipen()
usb3_first_req = usb3_get_request()
...
(the req is possible to be finished in the interrupt)
The usb3_first_req [1] above may have been finished after the interrupt
ended so that this driver caused to start a transfer wrongly. To fix this
issue, getting/checking the usb3_first_req are under spin_lock_irqsave()
in the same section.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210524060155.1178724-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89b1a3d811 upstream.
This adds support for the Startech.com generic serial to USB converter.
It seems to be a bone stock TI_3410. I have been using this patch for
years.
Signed-off-by: Sean MacLennan <seanm@seanm.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ea2e019c1 upstream.
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 746e4acf87 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the set-speed request which erroneously used USB_DIR_IN and update
the default timeout argument to match (same value).
Fixes: 5638e4d92e ("USB: add PlayStation 2 Trance Vibrator driver")
Cc: stable@vger.kernel.org # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133109.17396-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04f5b9f539 upstream.
AD7745 devices don't have the CIN2 pins and therefore can't handle related
channels. Forcing the number of AD7746 channels may lead to enabling more
channels than what the hardware actually supports.
Avoid num_channels being overwritten after first assignment.
Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Fixes: 83e416f458 ("staging: iio: adc: Replace, rewrite ad7745 from scratch.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b106776080 upstream.
Up to 64 bytes of data can be read from NVM in one go. Read address
must be dword aligned. Data is read into a local buffer.
If caller asks to read data starting at an unaligned address then full
dword is anyway read from NVM into a local buffer. Data is then copied
from the local buffer starting at the unaligned offset to the caller
buffer.
In cases where asked data length + unaligned offset is over 64 bytes
we need to make sure we don't read past the 64 bytes in the local
buffer when copying to caller buffer, and make sure that we don't
skip copying unaligned offset bytes from local buffer anymore after
the first round of 64 byte NVM data read.
Fixes: 3e13676862 ("thunderbolt: Add support for DMA configuration based mailbox")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e768532b2 upstream.
If an origin target has no snapshots, o->split_boundary is set to 0.
This causes BUG_ON(sectors <= 0) in block/bio.c:bio_split().
Fix this by initializing chunk_size, and in turn split_boundary, to
rounddown_pow_of_two(UINT_MAX) -- the largest power of two that fits
into "unsigned" type.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62a8ff67eb upstream.
In certain scenarios a normal MSDU can be received as an A-MSDU when
the A-MSDU present bit of a QoS header gets flipped during reception.
Since this bit is unauthenticated, the hardware crypto engine can pass
the frame to the driver without any error indication.
This could result in processing unintended subframes collected in the
A-MSDU list. Hence, validate A-MSDU list by checking if the first frame
has a valid subframe header.
Comparing the non-aggregated MSDU and an A-MSDU, the fields of the first
subframe DA matches the LLC/SNAP header fields of a normal MSDU.
In order to avoid processing such frames, add a validation to
filter such A-MSDU frames where the first subframe header DA matches
with the LLC/SNAP header pattern.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.10-00047
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.e6f5eb7b9847.I38a77ae26096862527a5eab73caebd7346af8b66@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3edc6b0d6c upstream.
For some chips/drivers, e.g., QCA6174 with ath10k, the decryption is
done by the hardware, and the Protected bit in the Frame Control field
is cleared in the lower level driver before the frame is passed to
mac80211. In such cases, the condition for ieee80211_has_protected() is
not met in ieee80211_rx_h_defragment() of mac80211 and the new security
validation steps are not executed.
Extend mac80211 to cover the case where the Protected bit has been
cleared, but the frame is indicated as having been decrypted by the
hardware. This extends protection against mixed key and fragment cache
attack for additional drivers/chips. This fixes CVE-2020-24586 and
CVE-2020-24587 for such cases.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.037aa5ca0390.I7bb888e2965a0db02a67075fcb5deb50eb7408aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8c4d76a8d upstream.
EAPOL frames are used for authentication and key management between the
AP and each individual STA associated in the BSS. Those frames are not
supposed to be sent by one associated STA to another associated STA
(either unicast for broadcast/multicast).
Similarly, in 802.11 they're supposed to be sent to the authenticator
(AP) address.
Since it is possible for unexpected EAPOL frames to result in misbehavior
in supplicant implementations, it is better for the AP to not allow such
cases to be forwarded to other clients either directly, or indirectly if
the AP interface is part of a bridge.
Accept EAPOL (control port) frames only if they're transmitted to the
own address, or, due to interoperability concerns, to the PAE group
address.
Disable forwarding of EAPOL (or well, the configured control port
protocol) frames back to wireless medium in all cases. Previously, these
frames were accepted from fully authenticated and authorized stations
and also from unauthenticated stations for one of the cases.
Additionally, to avoid forwarding by the bridge, rewrite the PAE group
address case to the local MAC address.
Cc: stable@vger.kernel.org
Co-developed-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.cb327ed0cabe.Ib7dcffa2a31f0913d660de65ba3c8aca75b1d10f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a11ce08c4 upstream.
Prior patches protected against fragmentation cache attacks
by coloring keys, but this shows that it can lead to issues
when multiple stations use the same sequence number. Add a
fragment cache to struct sta_info (in addition to the one in
the interface) to separate fragments for different stations
properly.
This then automatically clear most of the fragment cache when a
station disconnects (or reassociates) from an AP, or when client
interfaces disconnect from the network, etc.
On the way, also fix the comment there since this brings us in line
with the recommendation in 802.11-2016 ("An AP should support ...").
Additionally, remove a useless condition (since there's no problem
purging an already empty list).
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.fc35046b0d52.I1ef101e3784d13e8f6600d83de7ec9a3a45bcd52@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 270032a2a9 upstream.
With old ciphers (WEP and TKIP) we shouldn't be using A-MSDUs
since A-MSDUs are only supported if we know that they are, and
the only practical way for that is HT support which doesn't
support old ciphers.
However, we would normally accept them anyway. Since we check
the MMIC before deaggregating A-MSDUs, and the A-MSDU bit in
the QoS header is not protected in TKIP (or WEP), this enables
attacks similar to CVE-2020-24588. To prevent that, drop A-MSDUs
completely with old ciphers.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.076543300172.I548e6e71f1ee9cad4b9a37bf212ae7db723587aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b8a1fee34 upstream.
Mitigate A-MSDU injection attacks (CVE-2020-24588) by detecting if the
destination address of a subframe equals an RFC1042 (i.e., LLC/SNAP)
header, and if so dropping the complete A-MSDU frame. This mitigates
known attacks, although new (unknown) aggregation-based attacks may
remain possible.
This defense works because in A-MSDU aggregation injection attacks, a
normal encrypted Wi-Fi frame is turned into an A-MSDU frame. This means
the first 6 bytes of the first A-MSDU subframe correspond to an RFC1042
header. In other words, the destination MAC address of the first A-MSDU
subframe contains the start of an RFC1042 header during an aggregation
attack. We can detect this and thereby prevent this specific attack.
For details, see Section 7.2 of "Fragment and Forge: Breaking Wi-Fi
Through Frame Aggregation and Fragmentation".
Note that for kernel 4.9 and above this patch depends on "mac80211:
properly handle A-MSDUs that start with a rfc1042 header". Otherwise
this patch has no impact and attacks will remain possible.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.25d93176ddaf.I9e265b597f2cd23eb44573f35b625947b386a9de@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94034c40ab upstream.
Simultaneously prevent mixed key attacks (CVE-2020-24587) and fragment
cache attacks (CVE-2020-24586). This is accomplished by assigning a
unique color to every key (per interface) and using this to track which
key was used to decrypt a fragment. When reassembling frames, it is
now checked whether all fragments were decrypted using the same key.
To assure that fragment cache attacks are also prevented, the ID that is
assigned to keys is unique even over (re)associations and (re)connects.
This means fragments separated by a (re)association or (re)connect will
not be reassembled. Because mac80211 now also prevents the reassembly of
mixed encrypted and plaintext fragments, all cache attacks are prevented.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.3f8290e59823.I622a67769ed39257327a362cfc09c812320eb979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 965a7d72e7 upstream.
Do not mix plaintext and encrypted fragments in protected Wi-Fi
networks. This fixes CVE-2020-26147.
Previously, an attacker was able to first forward a legitimate encrypted
fragment towards a victim, followed by a plaintext fragment. The
encrypted and plaintext fragment would then be reassembled. For further
details see Section 6.3 and Appendix D in the paper "Fragment and Forge:
Breaking Wi-Fi Through Frame Aggregation and Fragmentation".
Because of this change there are now two equivalent conditions in the
code to determine if a received fragment requires sequential PNs, so we
also move this test to a separate function to make the code easier to
maintain.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.30c4394bb835.I5acfdb552cc1d20c339c262315950b3eac491397@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a6e9a9c68 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the tiocmset and rfkill requests which erroneously used
usb_rcvctrlpipe().
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c954eb72b3 upstream.
The decoder reports the current instruction if it was decoded. In some
cases the current instruction is not decoded, in which case the instruction
bytes length must be set to zero. Ensure that is always done.
Note perf script can anyway get the instruction bytes for any samples where
they are not present.
Also note, that there is a redundant "ptq->insn_len = 0" statement which is
not removed until a subsequent patch in order to make this patch apply
cleanly to stable branches.
Example:
A machne that supports TSX is required. It will have flag "rtm". Kernel
parameter tsx=on may be required.
# for w in `cat /proc/cpuinfo | grep -m1 flags `;do echo $w | grep rtm ; done
rtm
Test program:
#include <stdio.h>
#include <immintrin.h>
int main()
{
int x = 0;
if (_xbegin() == _XBEGIN_STARTED) {
x = 1;
_xabort(1);
} else {
printf("x = %d\n", x);
}
return 0;
}
Compile with -mrtm i.e.
gcc -Wall -Wextra -mrtm xabort.c -o xabort
Record:
perf record -e intel_pt/cyc/u --filter 'filter main @ ./xabort' ./xabort
Before:
# perf script --itrace=xe -F+flags,+insn,-period --xed --ns
xabort 1478 [007] 92161.431348581: transactions: x 400b81 main+0x14 (/root/xabort) mov $0xffffffff, %eax
xabort 1478 [007] 92161.431348624: transactions: tx abrt 400b93 main+0x26 (/root/xabort) mov $0xffffffff, %eax
After:
# perf script --itrace=xe -F+flags,+insn,-period --xed --ns
xabort 1478 [007] 92161.431348581: transactions: x 400b81 main+0x14 (/root/xabort) xbegin 0x6
xabort 1478 [007] 92161.431348624: transactions: tx abrt 400b93 main+0x26 (/root/xabort) xabort $0x1
Fixes: faaa87680b ("perf intel-pt/bts: Report instruction bytes and length in sample")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210519074515.9262-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a421d21860 upstream.
Commit de144ff423 changes _pnfs_return_layout() to call
pnfs_mark_matching_lsegs_return() passing NULL as the struct
pnfs_layout_range argument. Unfortunately,
pnfs_mark_matching_lsegs_return() doesn't check if we have a value here
before dereferencing it, causing an oops.
I'm able to hit this crash consistently when running connectathon basic
tests on NFS v4.1/v4.2 against Ontap.
Fixes: de144ff423 ("NFSv4: Don't discard segments marked for return in _pnfs_return_layout()")
Cc: stable@vger.kernel.org
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 175e476b8c upstream.
When a new table value was assigned, it was followed by a write memory
barrier. This ensured that all writes before this point would complete
before any writes after this point. However, to determine whether the
rules are unused, the sequence counter is read. To ensure that all
writes have been done before these reads, a full memory barrier is
needed, not just a write memory barrier. The same argument applies when
incrementing the counter, before the rules are read.
Changing to using smp_mb() instead of smp_wmb() fixes the kernel panic
reported in cc00bcaa58 (which is still present), while still
maintaining the same speed of replacing tables.
The smb_mb() barriers potentially slow the packet path, however testing
has shown no measurable change in performance on a 4-core MIPS64
platform.
Fixes: 7f5c6d4f66 ("netfilter: get rid of atomic ops in fast path")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[Ported to stable, affected barrier is added by d3d40f2374 in mainline]
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1d90dd272 upstream.
commit 72704f876f ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org
[jackp@codeaurora.org: backport to pre-5.7 by replacing
DWC3_IS_VER_PRIOR check with direct comparison of dwc->revision]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51839e29cb upstream.
Some distributions are about to switch to Python 3 support only.
This means that /usr/bin/python, which is Python 2, is not available
anymore. Hence, switch scripts to use Python 3 explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c25ce589dc upstream.
Change every shebang which does not need an argument to use /usr/bin/env.
This is needed as not every distro has everything under /usr/bin,
sometimes not even bash.
Signed-off-by: Finn Behrens <me@kloenk.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[nicolas@fjasle.eu: update contexts for v4.14, adapt for old scripts]
Signed-off-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 93b3a67448 upstream
Commit 93b3a67448 ("mm,vmstat: reduce zone->lock holding time by
/proc/pagetypeinfo") upstream caps the number of iterations over each
free_list at 100,000, and also drops the zone->lock in between each
migrate type. Capping the iteration count alters the file contents in
some cases, which means this approach may not be suitable for stable
backports.
However, dropping zone->lock in between migrate types (and, as a result,
page orders) will not change the /proc/pagetypeinfo file contents. It
can significantly reduce the length of time spent with IRQs disabled,
which can prevent missed interrupts or soft lockups which we have
observed on systems with particularly large memory.
Thus, this commit is a modified version of the upstream one which only
drops the lock in between migrate types.
Fixes: 467c996c1e ("Print out statistics in relation to fragmentation avoidance to /proc/pagetypeinfo")
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 860dafa902 upstream.
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d076336 ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
References:
[1] https://syzkaller.appspot.com/bug?id=32577e96d88447ded2d3b76d71254fb855245837
[2] https://syzkaller.appspot.com/bug?id=6b8355d27b2b94fb5cedf4655e3a59162d9e48e3
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d0ad57b3 upstream.
Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.
Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.
Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: e400b6ec4e ("vt/vgacon: Check if screen resize request comes from userspace")
Cc: stable@vger.kernel.org # v2.6.24+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6e337708c upstream.
niu_pci_eeprom_read() may fail, so add checks to its return value and
propagate the error up the callstack.
An examination of the callstack up to niu_pci_eeprom_read shows that:
niu_pci_eeprom_read() // returns int
niu_pci_vpd_scan_props() // returns int
niu_pci_vpd_fetch() // returns *void*
niu_get_invariants() // returns int
since niu_pci_vpd_fetch() returns void which breaks the bubbling up,
change its return type to int so that error is propagated upwards.
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Cc: Shannon Nelson <shannon.lee.nelson@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-24-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7930742d6a upstream.
This reverts commit 26fd962bde.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change here was incorrect. While it is nice to check if
niu_pci_eeprom_read() succeeded or not when using the data, any error
that might have happened was not propagated upwards properly, causing
the kernel to assume that these reads were successful, which results in
invalid data in the buffer that was to contain the successfully read
data.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Shannon Nelson <shannon.lee.nelson@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 26fd962bde ("niu: fix missing checks of niu_pci_eeprom_read")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-23-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b95b57dfe7 upstream.
This reverts commit 5bf7295fe3.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit does not properly detect if an error happens because the
logic after this loop will not detect that there was a failed
allocation.
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 5bf7295fe3 ("qlcnic: Avoid potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-25-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c5634c4a upstream.
This reverts commit 765976285a.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Bryan Brattlof <hello@bryanbrattlof.com>
Fixes: 765976285a ("rtlwifi: fix a potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9183f01b5e upstream.
As Peter points out, if we were to disconnect and then reconnect this
driver from a device, the "global" state of the device would contain odd
values and could cause problems. Fix this up by just initializing the
whole thing to 0 at probe() time.
Ideally this would be a per-device variable, but given the age and the
total lack of users of it, that would require a lot of s/./->/g changes
for really no good reason.
Reported-by: Peter Rosin <peda@axentia.se>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/YJP2j6AU82MqEY2M@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d03d1021da upstream.
The fields, "toc" and "cd_info", of "struct gdrom_unit gd" are allocated
in "probe_gdrom()". Prevent a memory leak by making sure "gd.cd_info" is
deallocated in the "remove_gdrom()" function.
Also prevent double free of the field "gd.toc" by moving it from the
module's exit function to "remove_gdrom()". This is because, in
"probe_gdrom()", the function makes sure to deallocate "gd.toc" in case
of any errors, so the exit function invoked later would again free
"gd.toc".
The patch also maintains consistency by deallocating the above mentioned
fields in "remove_gdrom()" along with another memory allocated field
"gd.disk".
Suggested-by: Jens Axboe <axboe@kernel.dk>
Cc: Peter Rosin <peda@axentia.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-28-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 257343d3ed upstream.
This reverts commit 093c48213e.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
Because of this, all submissions from this group must be reverted from
the kernel tree and will need to be re-reviewed again to determine if
they actually are a valid fix. Until that work is complete, remove this
change to ensure that no problems are being introduced into the
codebase.
Cc: Wenwen Wang <wang6495@umn.edu>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jens Axboe <axboe@kernel.dk>
Fixes: 093c48213e ("gdrom: fix a memory leak bug")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-27-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1436df2f2 upstream.
This reverts commit 2c2a7552dd.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit log for this change was incorrect, no "error
handling code" was added, things will blow up just as badly as before if
any of these cases ever were true. As this BUG_ON() never fired, and
most of these checks are "obviously" never going to be true, let's just
revert to the original code for now until this gets unwound to be done
correctly in the future.
Cc: Aditya Pakki <pakki001@umn.edu>
Fixes: 2c2a7552dd ("ecryptfs: replace BUG_ON with error handling code")
Cc: stable <stable@vger.kernel.org>
Acked-by: Tyler Hicks <code@tyhicks.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-49-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed04fe8a0e upstream.
This reverts commit 1d84353d20.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here, while technically correct, did not fully
handle all of the reported issues that the commit stated it was fixing,
so revert it until it can be "fixed" fully.
Note, ioremap() probably will never fail for old hardware like this, and
if anyone actually used this hardware (a PowerMac era PCI display card),
they would not be using fbdev anymore.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fixes: 1d84353d20 ("video: imsttfb: fix potential NULL pointer dereferences")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-67-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ae341767 upstream.
This reverts commit 9aa3aa15f4.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu>
Fixes: 9aa3aa15f4 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe")
Cc: stable <stable@vger.kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d1beda5f1 upstream.
This reverts commit 248b57015f.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit does not properly unwind if there is an error
condition so it needs to be reverted at this point in time.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 248b57015f ("leds: lp5523: fix a missing check of return value of lp55xx_read")
Link: https://lore.kernel.org/r/20210503115736.2104747-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bee1b05118 upstream.
This reverts commit f86a3b8383.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: David S. Miller <davem@davemloft.net>
Fixes: f86a3b8383 ("net: stmicro: fix a missing check of clk_prepare")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58c0cc2d90 upstream.
This reverts commit ec7f6aad57.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This patch "looks" correct, but the driver keeps on running and will
fail horribly right afterward if this error condition ever trips.
So points for trying to resolve an issue, but a huge NEGATIVE value for
providing a "fake" fix for the problem as nothing actually got resolved
at all. I'll go fix this up properly...
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Ferenc Bakonyi <fero@drama.obuda.kando.hu>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: ec7f6aad57 ("video: hgafb: fix potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-39-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c699a0db2d upstream.
The following commands will crash the kernel:
modprobe brd rd_size=1048576
dmsetup create o --table "0 `blockdev --getsize /dev/ram0` snapshot-origin /dev/ram0"
dmsetup create s --table "0 `blockdev --getsize /dev/ram0` snapshot /dev/ram0 /dev/ram1 N 0"
The reason is that when we test for zero chunk size, we jump to the label
bad_read_metadata without setting the "r" variable. The function
snapshot_ctr destroys all the structures and then exits with "r == 0". The
kernel then crashes because it falsely believes that snapshot_ctr
succeeded.
In order to fix the bug, we set the variable "r" to -EINVAL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c81d3d2460 upstream.
When multiple PCI devices get assigned to a guest right at boot, libxl
incrementally populates the backend tree. The writes for the first of
the devices trigger the backend watch. In turn xen_pcibk_setup_backend()
will set the XenBus state to Initialised, at which point no further
reconfigures would happen unless a device got hotplugged. Arrange for
reconfigure to also get triggered from the backend watch handler.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/2337cbd6-94b9-4187-9862-c03ea12e0c61@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8822702f6e upstream.
Ubuntu users reported an audio bug on the Lenovo Yoga Slim 7 14IIL05,
he installed dual OS (Windows + Linux), if he booted to the Linux
from Windows, the Speaker can't work well, it has crackling noise,
if he poweroff the machine first after Windows, the Speaker worked
well.
Before rebooting or shutdown from Windows, the Windows changes the
codec eapd coeff value, but the BIOS doesn't re-initialize its value,
when booting into the Linux from Windows, the eapd coeff value is not
correct. To fix it, set the codec default value to that coeff register
in the alsa driver.
BugLink: http://bugs.launchpad.net/bugs/1925057
Suggested-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210507024452.8300-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94f88309f2 upstream.
This reverts commit dcd0feac9b.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit message for this change was incorrect as the code
path can never result in a NULL dereference, alluding to the fact that
whatever tool was used to "find this" is broken. It's just an optional
resource reservation, so removing this check is fine.
Cc: Kangjie Lu <kjlu@umn.edu>
Acked-by: Takashi Iwai <tiwai@suse.de>
Fixes: dcd0feac9b ("ALSA: sb8: add a check for request_region")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-35-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0edabdfe89 upstream.
Mackie d.2 has an extension card for IEEE 1394 communication, which uses
BridgeCo DM1000 ASIC. On the other hand, Mackie d.4 Pro has built-in
function for IEEE 1394 communication by Oxford Semiconductor OXFW971,
according to schematic diagram available in Mackie website. Although I
misunderstood that Mackie d.2 Pro would be also a model with OXFW971,
it's wrong. Mackie d.2 Pro is a model which includes the extension card
as factory settings.
This commit fixes entries in Kconfig and comment in ALSA OXFW driver.
Cc: <stable@vger.kernel.org>
Fixes: fd6f4b0dc1 ("ALSA: bebob: Add skelton for BeBoB based devices")
Fixes: ec4dba5053 ("ALSA: oxfw: Add support for Behringer/Mackie devices")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210513125652.110249-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ca447630 upstream.
The initialization of MIDI devices that are found on some LINE6
drivers are currently done in a racy way; namely, the MIDI buffer
instance is allocated and initialized in each private_init callback
while the communication with the interface is already started via
line6_init_cap_control() call before that point. This may lead to
Oops in line6_data_received() when a spurious event is received, as
reported by syzkaller.
This patch moves the MIDI initialization to line6_init_cap_control()
as well instead of the too-lately-called private_init for avoiding the
race. Also this reduces slightly more lines, so it's a win-win
change.
Reported-by: syzbot+0d2b3feb0a2887862e06@syzkallerlkml..appspotmail.com
Link: https://lore.kernel.org/r/000000000000a4be9405c28520de@google.com
Link: https://lore.kernel.org/r/20210517132725.GA50495@hyeyoo
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210518083939.1927-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d201d7631c upstream.
When using smb2_copychunk_range() for large ranges we will
run through several iterations of a loop calling SMB2_ioctl()
but never actually free the returned buffer except for the final
iteration.
This leads to memory leaks everytime a large copychunk is requested.
Fixes: 9bf0c9cd43 ("CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files")
Cc: <stable@vger.kernel.org>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dbb5afad10 ]
Suppose we have 2 threads, the group-leader L and a sub-theread T,
both parked in ptrace_stop(). Debugger tries to resume both threads
and does
ptrace(PTRACE_CONT, T);
ptrace(PTRACE_CONT, L);
If the sub-thread T execs in between, the 2nd PTRACE_CONT doesn not
resume the old leader L, it resumes the post-exec thread T which was
actually now stopped in PTHREAD_EVENT_EXEC. In this case the
PTHREAD_EVENT_EXEC event is lost, and the tracer can't know that the
tracee changed its pid.
This patch makes ptrace() fail in this case until debugger does wait()
and consumes PTHREAD_EVENT_EXEC which reports old_pid. This affects all
ptrace requests except the "asynchronous" PTRACE_INTERRUPT/KILL.
The patch doesn't add the new PTRACE_ option to not complicate the API,
and I _hope_ this won't cause any noticeable regression:
- If debugger uses PTRACE_O_TRACEEXEC and the thread did an exec
and the tracer does a ptrace request without having consumed
the exec event, it's 100% sure that the thread the ptracer
thinks it is targeting does not exist anymore, or isn't the
same as the one it thinks it is targeting.
- To some degree this patch adds nothing new. In the scenario
above ptrace(L) can fail with -ESRCH if it is called after the
execing sub-thread wakes the leader up and before it "steals"
the leader's pid.
Test-case:
#include <stdio.h>
#include <unistd.h>
#include <signal.h>
#include <sys/ptrace.h>
#include <sys/wait.h>
#include <errno.h>
#include <pthread.h>
#include <assert.h>
void *tf(void *arg)
{
execve("/usr/bin/true", NULL, NULL);
assert(0);
return NULL;
}
int main(void)
{
int leader = fork();
if (!leader) {
kill(getpid(), SIGSTOP);
pthread_t th;
pthread_create(&th, NULL, tf, NULL);
for (;;)
pause();
return 0;
}
waitpid(leader, NULL, WSTOPPED);
ptrace(PTRACE_SEIZE, leader, 0,
PTRACE_O_TRACECLONE | PTRACE_O_TRACEEXEC);
waitpid(leader, NULL, 0);
ptrace(PTRACE_CONT, leader, 0,0);
waitpid(leader, NULL, 0);
int status, thread = waitpid(-1, &status, 0);
assert(thread > 0 && thread != leader);
assert(status == 0x80137f);
ptrace(PTRACE_CONT, thread, 0,0);
/*
* waitid() because waitpid(leader, &status, WNOWAIT) does not
* report status. Why ????
*
* Why WEXITED? because we have another kernel problem connected
* to mt-exec.
*/
siginfo_t info;
assert(waitid(P_PID, leader, &info, WSTOPPED|WEXITED|WNOWAIT) == 0);
assert(info.si_pid == leader && info.si_status == 0x0405);
/* OK, it sleeps in ptrace(PTRACE_EVENT_EXEC == 0x04) */
assert(ptrace(PTRACE_CONT, leader, 0,0) == -1);
assert(errno == ESRCH);
assert(leader == waitpid(leader, &status, WNOHANG));
assert(status == 0x04057f);
assert(ptrace(PTRACE_CONT, leader, 0,0) == 0);
return 0;
}
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Simon Marchi <simon.marchi@efficios.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pedro Alves <palves@redhat.com>
Acked-by: Simon Marchi <simon.marchi@efficios.com>
Acked-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c019d92457 ]
'setup_find_cpu_node()' take a reference on the node it returns.
This reference must be decremented when not needed anymore, or there will
be a leak.
Add the missing 'of_node_put(cpu)'.
Note that 'setup_cpuinfo()' that also calls this function already has a
correct 'of_node_put(cpu)' at its end.
Fixes: 9d02a4283e ("OpenRISC: Boot code")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0d7a7b2014 upstream.
My previous commits added a dev_hold() in tunnels ndo_init(),
but forgot to remove it from special functions setting up fallback tunnels.
Fallback tunnels do call their respective ndo_init()
This leads to various reports like :
unregister_netdevice: waiting for ip6gre0 to become free. Usage count = 2
Fixes: 48bb569726 ("ip6_tunnel: sit: proper dev_{hold|put} in ndo_[un]init methods")
Fixes: 6289a98f08 ("sit: proper dev_{hold|put} in ndo_[un]init methods")
Fixes: 40cb881b5a ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods")
Fixes: 7f700334be ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6289a98f08 upstream.
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding prior dev_hold().
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
Fixes: 919067cc84 ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b86f86e8e7 ]
Canceling hrtimer when holding uart spinlock can deadlock.
CPU0: syscall write
-> get uart port spinlock
-> write uart
-> start_tx_rs485
-> hrtimer_cancel
-> wait for hrtimer callback to finish
CPU1: hrtimer IRQ
-> run hrtimer
-> em485_handle_stop_tx
-> get uart port spinlock
CPU0 is waiting for the hrtimer callback to finish, but the hrtimer
callback running on CPU1 is waiting to get the uart port spinlock.
This deadlock can be avoided by not canceling the hrtimers in these paths.
Setting active_timer=NULL can be done without accessing hrtimer,
and that will effectively cancel operations that would otherwise have been
performed by the hrtimer callback.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f48652bbe3 ]
Without this change, the DAC ctl's name could be changed only when
the machine has both Speaker and Headphone, but we met some machines
which only has Lineout and Headhpone, and the Lineout and Headphone
share the Audio Mixer0 and DAC0, the ctl's name is set to "Front".
On most of machines, the "Front" is used for Speaker only or Lineout
only, but on this machine it is shared by Lineout and Headphone,
This introduces an issue in the pipewire and pulseaudio, suppose users
want the Headphone to be on and the Speaker/Lineout to be off, they
could turn off the "Front", this works on most of the machines, but on
this machine, the "Front" couldn't be turned off otherwise the
headphone will be off too. Here we do some change to let the ctl's
name change to "Headphone+LO" on this machine, and pipewire and
pulseaudio already could handle "Headphone+LO" and "Speaker+LO".
(https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/747)
BugLink: http://bugs.launchpad.net/bugs/804178
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210504073917.22406-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da91ece226 ]
Like some other Bay and Cherry Trail SoC based devices the Dell Venue
10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to
report events instead of using the standard ACPI EC interface for this.
The EC interrupt is only used to report battery-level changes and
it keeps doing this while the system is suspended, causing the system
to not stay suspended.
Add an ignore-wake quirk for the GPIO pin used by the EC to fix the
spurious wakeups from suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5027ca63e ]
Ritesh reported a bug [1] against UML, noting that it crashed on
startup. The backtrace shows the following (heavily redacted):
(gdb) bt
...
#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268
#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2
#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72
...
#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359
...
#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486
#45 0x00007f8990968b85 in __getgrnam_r [...]
#46 0x00007f89909d6b77 in grantpt [...]
#47 0x00007f8990a9394e in __GI_openpty [...]
#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407
#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598
#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45
#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334
#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144
indicating that the UML function openpty_cb() calls openpty(),
which internally calls __getgrnam_r(), which causes the nsswitch
machinery to get started.
This loads, through lots of indirection that I snipped, the
libcom_err.so.2 library, which (in an unknown function, "??")
calls sem_init().
Now, of course it wants to get libpthread's sem_init(), since
it's linked against libpthread. However, the dynamic linker
looks up that symbol against the binary first, and gets the
kernel's sem_init().
Hajime Tazaki noted that "objcopy -L" can localize a symbol,
so the dynamic linker wouldn't do the lookup this way. I tried,
but for some reason that didn't seem to work.
Doing the same thing in the linker script instead does seem to
work, though I cannot entirely explain - it *also* works if I
just add "VERSION { { global: *; }; }" instead, indicating that
something else is happening that I don't really understand. It
may be that explicitly doing that marks them with some kind of
empty version, and that's different from the default.
Explicitly marking them with a version breaks kallsyms, so that
doesn't seem to be possible.
Marking all the symbols as local seems correct, and does seem
to address the issue, so do that. Also do it for static link,
nsswitch libraries could still be loaded there.
[1] https://bugs.debian.org/983379
Reported-by: Ritesh Raj Sarraf <rrs@debian.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Tested-By: Ritesh Raj Sarraf <rrs@debian.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e479187748 ]
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65299e8bfb ]
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bbfd31903 ]
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com
Signed-off-by: Feilong Lin <linfeilong@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8252ca87c7 ]
Enabling function_graph tracer on ARM causes kernel panic, because the
function graph tracer updates the "return address" of a function in order
to insert a trace callback on function exit, it saves the function's
original return address in a return trace stack, but cpu_suspend() may not
return through the normal return path.
cpu_suspend() will resume directly via the cpu_resume path, but the return
trace stack has been set-up by the subfunctions of cpu_suspend(), which
makes the "return address" inconsistent with cpu_suspend().
This patch refers to Commit de818bd452
("arm64: kernel: pause/unpause function graph tracer in cpu_suspend()"),
fixes the issue by pausing/resuming the function graph tracer on the thread
executing cpu_suspend(), so that the function graph tracer state is kept
consistent across functions that enter power down states and never return
by effectively disabling graph tracer while they are executing.
Signed-off-by: louis.wang <liang26812@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16f7ae5906 ]
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5ee7d4c7fb upstream.
gcc-11 complains about a prototype declaration that is different
from the function definition:
drivers/isdn/capi/kcapi.c:724:44: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
724 | u16 capi20_get_manufacturer(u32 contr, u8 *buf)
| ~~~~^~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:62:43: note: previously declared as an array ‘u8[64]’ {aka ‘unsigned char[64]’}
62 | u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/capi/kcapi.c:790:38: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
790 | u16 capi20_get_serial(u32 contr, u8 *serial)
| ~~~~^~~~~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:64:37: note: previously declared as an array ‘u8[8]’ {aka ‘unsigned char[8]’}
64 | u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~
Change the definition to make them match.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8460f6003a upstream.
gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164244.827589-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40cc3a80bb upstream.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
Fixes: e8d31c204e ("kgdb: add kgdb internal test suite")
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210322164308.827846-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 396a66aa11 upstream.
gcc-11 warns about mismatched prototypes here:
arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}
GCC is right here - fix up the types.
[ mingo: Twiddled the changelog. ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210322164541.912261-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34138a59b9 upstream.
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2671fa4dc0 upstream.
These sysctls point to global variables:
- NF_SYSCTL_CT_MAX (&nf_conntrack_max)
- NF_SYSCTL_CT_EXPECT_MAX (&nf_ct_expect_max)
- NF_SYSCTL_CT_BUCKETS (&nf_conntrack_htable_size_user)
Because their data pointers are not updated to point to per-netns
structures, they must be marked read-only in a non-init_net ns.
Otherwise, changes in any net namespace are reflected in (leaked into)
all other net namespaces. This problem has existed since the
introduction of net namespaces.
The current logic marks them read-only only if the net namespace is
owned by an unprivileged user (other than init_user_ns).
Commit d0febd81ae ("netfilter: conntrack: re-visit sysctls in
unprivileged namespaces") "exposes all sysctls even if the namespace is
unpriviliged." Since we need to mark them readonly in any case, we can
forego the unprivileged user check altogether.
Fixes: d0febd81ae ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces")
Signed-off-by: Jonathon Reinhart <Jonathon.Reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25ab14cbe9 upstream.
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d337d45e upstream.
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c49f71f607 upstream.
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.")
Reported-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 193ced4a79 upstream.
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
The default kernel configuration choice for the defxx driver is the use
of I/O ports rather than MMIO for PCI and EISA systems. It may have
made sense as a conservative backwards compatible choice back when MMIO
operation support was added to the driver as a part of TURBOchannel bus
support. However nowadays this configuration choice makes the driver
unusable with systems that do not implement I/O transactions for PCIe.
Make DEFXX_MMIO the configuration default then, except where configured
for EISA. This exception is because an EISA adapter can have its MMIO
decoding disabled with ECU (EISA Configuration Utility) and therefore
not available with the resource allocation infrastructure we implement,
while port I/O is always readily available as it uses slot-specific
addressing, directly mapped to the slot an option card has been placed
in and handled with our EISA bus support core. Conversely a kernel that
supports modern systems which may not have I/O transactions implemented
for PCIe will usually not be expected to handle legacy EISA systems.
The change of the default will make it easier for people, including but
not limited to distribution packagers, to make a working choice for the
driver.
Update the option description accordingly and while at it replace the
potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports"
according to our nomenclature used elsewhere.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: e89a2cfb7d ("[TC] defxx: TURBOchannel support")
Cc: stable@vger.kernel.org # v2.6.21+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 594b27e677 upstream.
Nothing prevents the following:
pvclock_gtod_notify()
queue_work(system_long_wq, &pvclock_gtod_work);
...
remove_module(kvm);
...
work_queue_run()
pvclock_gtod_work() <- UAF
Ditto for any other operation on that workqueue list head which touches
pvclock_gtod_work after module removal.
Cancel the work in kvm_arch_exit() to prevent that.
Fixes: 16e8d74d2d ("KVM: x86: notifier for clocksource changes")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Message-Id: <87czu4onry.ffs@nanos.tec.linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af0e1871d7 upstream.
The lux_val returned from tsl2583_get_lux can potentially be zero,
so check for this to avoid a division by zero and an overflowed
gain_trim_val.
Fixes clang scan-build warning:
drivers/iio/light/tsl2583.c:345:40: warning: Either the
condition 'lux_val<0' is redundant or there is division
by zero at line 345. [zerodivcond]
Fixes: ac4f6eee8f ("staging: iio: TAOS tsl258x: Device driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75a41ce46b upstream.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcd ("usb: dwc2: gadget: manage ep0 state in software")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e17b02d497 upstream.
When extcon is used in combination with dwc3, it is assumed that the dwc3
registers are untouched and as such are only configured if VBUS is valid
or ID is tied to ground.
In case VBUS is not valid or ID is floating, the registers are not
configured as such during driver initialization, causing a wrong
default state during boot.
If the registers are not in a default state, because they are for
instance touched by a boot loader, this can cause for a kernel error.
Signed-off-by: Marcel Hamer <marcel@solidxs.se>
Link: https://lore.kernel.org/r/20210427122118.1948340-1-marcel@solidxs.se
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 630ef623ed ]
If a tag set is shared across request queues (e.g. SCSI LUNs) then the
block layer core keeps track of the number of active request queues in
tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that
atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make
sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is
cleared by blk_mq_del_queue_tag_set().
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Fixes: 0d2602ca30 ("blk-mq: improve support for shared tags maps")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210513171529.7977-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 227545b9a0 upstream.
Screen flickers rapidly when two 4K 60Hz monitors are in use. This issue
doesn't happen when one monitor is 4K 60Hz (pixelclock 594MHz) and
another one is 4K 30Hz (pixelclock 297MHz).
The issue is gone after setting "power_dpm_force_performance_level" to
"high". Following the indication, we found that the issue occurs when
sclk is too low.
So resolve the issue by disabling sclk switching when there are two
monitors requires high pixelclock (> 297MHz).
v2:
- Only apply the fix to Oland.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ed9d238c7 upstream.
Consider the following sequence of events:
1. Userspace issues a UFFD ioctl, which ends up calling into
shmem_mfill_atomic_pte(). We successfully account the blocks, we
shmem_alloc_page(), but then the copy_from_user() fails. We return
-ENOENT. We don't release the page we allocated.
2. Our caller detects this error code, tries the copy_from_user() after
dropping the mmap_lock, and retries, calling back into
shmem_mfill_atomic_pte().
3. Meanwhile, let's say another process filled up the tmpfs being used.
4. So shmem_mfill_atomic_pte() fails to account blocks this time, and
immediately returns - without releasing the page.
This triggers a BUG_ON in our caller, which asserts that the page
should always be consumed, unless -ENOENT is returned.
To fix this, detect if we have such a "dangling" page when accounting
fails, and if so, release it before returning.
Link: https://lkml.kernel.org/r/20210428230858.348400-1-axelrasmussen@google.com
Fixes: cb658a453b ("userfaultfd: shmem: avoid leaking blocks and used blocks in UFFDIO_COPY")
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reported-by: Hugh Dickins <hughd@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec86b052d upstream.
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
sleeper[15639]: segfault (11) at c000000000004c20 nip c000000000004c20 lr c000000000004c20
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: f79643787e ("powerpc/64s: flush L1D on kernel entry")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec7791bae upstream.
The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
User access of kernel address (c00000003fff5af0) - exploit attempt? (uid: 0)
segfault (11) at c00000003fff5af0 nip 7fff8ad12198 lr 7fff8ad121f8 code 1
code: 40820128 e93c00d0 e9290058 7c292840 40810058 38600000 4bfd9a81 e8410018
code: 2c030006 41810154 3860ffb6 e9210098 <e94d8ff0> 7d295279 39400000 40820a3c
Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: a048a07d7f ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3433adc8bd upstream.
We have NR_syscall syscalls from [0 .. NR_syscall-1].
However the check for invalid syscall number is "> NR_syscall" as
opposed to >=. This off-by-one error erronesously allows "NR_syscall"
to be treated as valid syscall causeing out-of-bounds access into
syscall-call table ensuing a crash (holes within syscall table have a
invalid-entry handler but this is beyond the array implementing the
table).
This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10
kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has
NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was
not handled as -ENOSYS but processed leading to a crash.
Link: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/48
Reported-by: Shahab Vahedi <shahab@synopsys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c16db6c92 ]
Android userspace has been using TCA_KIND with a char[IFNAMESIZ]
many-null-terminated buffer containing the string 'bpf'.
This works on 4.19 and ceases to work on 5.10.
I'm not entirely sure what fixes tag to use, but I think the issue
was likely introduced in the below mentioned 5.4 commit.
Reported-by: Nucca Chen <nuccachen@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Fixes: 62794fc4fb ("net_sched: add max len check for TCA_KIND")
Change-Id: I66dc281f165a2858fc29a44869a270a2d698a82b
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c89a384e25 ]
When removing rmap_item from stable tree, STABLE_FLAG of rmap_item is
cleared with head reserved. So the following scenario might happen: For
ksm page with rmap_item1:
cmp_and_merge_page
stable_node->head = &migrate_nodes;
remove_rmap_item_from_tree, but head still equal to stable_node;
try_to_merge_with_ksm_page failed;
return;
For the same ksm page with rmap_item2, stable node migration succeed this
time. The stable_node->head does not equal to migrate_nodes now. For ksm
page with rmap_item1 again:
cmp_and_merge_page
stable_node->head != &migrate_nodes && rmap_item->head == stable_node
return;
We would miss the rmap_item for stable_node and might result in failed
rmap_walk_ksm(). Fix this by set rmap_item->head to NULL when rmap_item
is removed from stable tree.
Link: https://lkml.kernel.org/r/20210330140228.45635-5-linmiaohe@huawei.com
Fixes: 4146d2d673 ("ksm: make !merge_across_nodes migration safe")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f282df0391 ]
Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into
ESTABLISHED from the state < ESTABLISHED and decremented when the asoc
is being deleted.
However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to
ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment
SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB
multiple times but only decrement once at the end.
I was able to reproduce it by using scapy to do the 4-way shakehands,
after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field
changed to different values, and SCTP_MIB_CURRESTAB was incremented
multiple times and never went back to 0 even when the asoc was freed.
This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when
the state < ESTABLISHED in sctp_sf_do_dupcook_b().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73f5c88f52 ]
Currently the client ignores the value of the sr_eof of the SEEK
operation. According to the spec, if the server didn't find the
requested extent and reached the end of the file, the server
would return sr_eof=true. In case the request for DATA and no
data was found (ie in the middle of the hole), then the lseek
expects that ENXIO would be returned.
Fixes: 1c6dcbe5ce ("NFS: Implement SEEK")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed34695e15 ]
We (adam zabrocki, alexander matrosov, alexander tereshkin, maksym
bazalii) observed the check:
if (fh->size > sizeof(struct nfs_fh))
should not use the size of the nfs_fh struct which includes an extra two
bytes from the size field.
struct nfs_fh {
unsigned short size;
unsigned char data[NFS_MAXFHSIZE];
}
but should determine the size from data[NFS_MAXFHSIZE] so the memcpy
will not write 2 bytes beyond destination. The proposed fix is to
compare against the NFS_MAXFHSIZE directly, as is done elsewhere in fs
code base.
Fixes: d67ae825a5 ("pnfs/flexfiles: Add the FlexFile Layout Driver")
Signed-off-by: Nikola Livic <nlivic@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdbfad177 ]
We need to use unsigned long subtraction and then convert to signed in
order to deal correcly with C overflow rules.
Fixes: f506200346 ("NFS: Set an attribute barrier on all updates")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99f2378322 ]
Whether we're allocating or delallocating space, we should flush out the
pending writes in order to avoid races with attribute updates.
Fixes: 1e564d3dbd ("NFSv4.2: Fix a race in nfs42_proc_deallocate()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28e18ee636 ]
The uninitialized variable dn.node_changed does not get set when a
call to f2fs_get_node_page fails. This uninitialized value gets used
in the call to f2fs_balance_fs() that may or not may not balances
dirty node and dentry pages depending on the uninitialized state of
the variable. Fix this by only calling f2fs_balance_fs if err is
not set.
Thanks to Jaegeuk Kim for suggesting an appropriate fix.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 2a34076070 ("f2fs: call f2fs_balance_fs only when node was changed")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f57d8c40f ]
The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc7130bf11 ]
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock:
c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock:
c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(p->lock)/1);
lock(&(p->lock)/1);
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210301063653.51003-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb43e5718d ]
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_req drivers/net/wireless/wl3501_cs.o
struct wl3501_req {
u16 beacon_period; /* 0 2 */
u16 dtim_period; /* 2 2 */
u16 cap_info; /* 4 2 */
u8 bss_type; /* 6 1 */
u8 bssid[6]; /* 7 6 */
struct iw_mgmt_essid_pset ssid; /* 13 34 */
struct iw_mgmt_ds_pset ds_pset; /* 47 3 */
struct iw_mgmt_cf_pset cf_pset; /* 50 8 */
struct iw_mgmt_ibss_pset ibss_pset; /* 58 4 */
struct iw_mgmt_data_rset bss_basic_rset; /* 62 10 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
$ pahole -C wl3501_join_req drivers/net/wireless/wl3501_cs.o
struct wl3501_join_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
struct iw_mgmt_data_rset operational_rset; /* 4 10 */
u16 reserved2; /* 14 2 */
u16 timeout; /* 16 2 */
u16 probe_delay; /* 18 2 */
u8 timestamp[8]; /* 20 8 */
u8 local_time[8]; /* 28 8 */
struct wl3501_req req; /* 36 72 */
/* size: 108, cachelines: 2, members: 10 */
/* last cacheline: 44 bytes */
};
$ pahole -C wl3501_scan_confirm drivers/net/wireless/wl3501_cs.o
struct wl3501_scan_confirm {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
u16 status; /* 4 2 */
char timestamp[8]; /* 6 8 */
char localtime[8]; /* 14 8 */
struct wl3501_req req; /* 22 72 */
/* --- cacheline 1 boundary (64 bytes) was 30 bytes ago --- */
u8 rssi; /* 94 1 */
/* size: 96, cachelines: 2, members: 8 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1fbaf516da763b50edac47d792a9145aa4482e29.1618442265.git.gustavoars@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820aa37638 ]
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_md_req drivers/net/wireless/wl3501_cs.o
struct wl3501_md_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 pri; /* 8 1 */
u8 service_class; /* 9 1 */
struct {
u8 daddr[6]; /* 10 6 */
u8 saddr[6]; /* 16 6 */
} addr; /* 10 12 */
/* size: 22, cachelines: 1, members: 8 */
/* last cacheline: 22 bytes */
};
$ pahole -C wl3501_md_ind drivers/net/wireless/wl3501_cs.o
struct wl3501_md_ind {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 reception; /* 8 1 */
u8 pri; /* 9 1 */
u8 service_class; /* 10 1 */
struct {
u8 daddr[6]; /* 11 6 */
u8 saddr[6]; /* 17 6 */
} addr; /* 11 12 */
/* size: 24, cachelines: 1, members: 9 */
/* padding: 1 */
/* last cacheline: 24 bytes */
};
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d260fe56aed7112bff2be5b4d152d03ad7b78e78.1618442265.git.gustavoars@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed8029d7b4 ]
RCU complains about us calling printk() from an offline CPU:
=============================
WARNING: suspicious RCU usage
5.12.0-rc7-02874-g7cf90e481cb8 #1 Not tainted
-----------------------------
kernel/locking/lockdep.c:3568 RCU-list traversed in non-reader section!!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc7-02874-g7cf90e481cb8 #1
Call Trace:
dump_stack+0xec/0x144 (unreliable)
lockdep_rcu_suspicious+0x124/0x144
__lock_acquire+0x1098/0x28b0
lock_acquire+0x128/0x600
_raw_spin_lock_irqsave+0x6c/0xc0
down_trylock+0x2c/0x70
__down_trylock_console_sem+0x60/0x140
vprintk_emit+0x1a8/0x4b0
vprintk_func+0xcc/0x200
printk+0x40/0x54
pseries_cpu_offline_self+0xc0/0x120
arch_cpu_idle_dead+0x54/0x70
do_idle+0x174/0x4a0
cpu_startup_entry+0x38/0x40
rest_init+0x268/0x388
start_kernel+0x748/0x790
start_here_common+0x1c/0x614
Which happens because by the time we get to rtas_stop_self() we are
already offline. In addition the message can be spammy, and is not that
helpful for users, so remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210418135413.1204031-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5272ad4aa ]
Fix the following out-of-bounds warning:
net/sctp/sm_make_chunk.c:3150:4: warning: 'memcpy' offset [17, 28] from the object at 'addr' is out of the bounds of referenced subobject 'v4' with type 'struct sockaddr_in' at offset 0 [-Warray-bounds]
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c94b430b9 ]
If the user selects the very first entry in a page and performs a
search-up operation, or selects the very last entry in a page and
performs a search-down operation that will not succeed (e.g., via
[/]asdfzzz[Up Arrow]), nconf will never terminate searching the page.
The reason is that in this case, the starting point will be set to -1
or n, which is then translated into (n - 1) (i.e., the last entry of
the page) or 0 (i.e., the first entry of the page) and finally the
search begins. This continues to work fine until the index reaches 0 or
(n - 1), at which point it will be decremented to -1 or incremented to
n, but not checked against the starting point right away. Instead, it's
wrapped around to the bottom or top again, after which the starting
point check occurs... and naturally fails.
My original implementation added another check for -1 before wrapping
the running index variable around, but Masahiro Yamada pointed out that
the actual issue is that the comparison point (starting point) exceeds
bounds (i.e., the [0,n-1] interval) in the first place and that,
instead, the starting point should be fixed.
This has the welcome side-effect of also fixing the case where the
starting point was n while searching down, which also lead to an
infinite loop.
OTOH, this code is now essentially all his work.
Amazingly, nobody seems to have been hit by this for 11 years - or at
the very least nobody bothered to debug and fix this.
Signed-off-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26e6dd1072 ]
selftests/bpf/Makefile includes lib.mk. With the following command
make -j60 LLVM=1 LLVM_IAS=1 <=== compile kernel
make -j60 -C tools/testing/selftests/bpf LLVM=1 LLVM_IAS=1 V=1
some files are still compiled with gcc. This patch
fixed lib.mk issue which sets CC to gcc in all cases.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210413153413.3027426-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8217673d07 ]
For cloned connections cuse_channel_release() will be called more than
once, resulting in use after free.
Prevent device cloning for CUSE, which does not make sense at this point,
and highly unlikely to be used in real life.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0c10a5f3 ]
The Special Function Registers on all Exynos SoC, including ARM64, are
32-bit wide, so entire driver uses matching functions like readl() or
writel(). On 64-bit ARM using unsigned long for register masks:
1. makes little sense as immediately after bitwise operation it will be
cast to 32-bit value when calling writel(),
2. is actually error-prone because it might promote other operands to
64-bit.
Addresses-Coverity: Unintentional integer overflow
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20210408195029.69974-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6843d1ee2 ]
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210408143124.b9e68aa98304.I465afb55ca2c7d59f7bf610c6046a1fd732b4c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a9d54b194 ]
Currently l2cap_chan_set_defaults() reset chan->conf_state to zero.
However, there is a flag CONF_NOT_COMPLETE which is set when
creating the l2cap_chan. It is suggested that the flag should be
cleared when l2cap_chan is ready, but when l2cap_chan_set_defaults()
is called, l2cap_chan is not yet ready. Therefore, we must set this
flag as the default.
Example crash call trace:
__dump_stack lib/dump_stack.c:15 [inline]
dump_stack+0xc4/0x118 lib/dump_stack.c:56
panic+0x1c6/0x38b kernel/panic.c:117
__warn+0x170/0x1b9 kernel/panic.c:471
warn_slowpath_fmt+0xc7/0xf8 kernel/panic.c:494
debug_print_object+0x175/0x193 lib/debugobjects.c:260
debug_object_assert_init+0x171/0x1bf lib/debugobjects.c:614
debug_timer_assert_init kernel/time/timer.c:629 [inline]
debug_assert_init kernel/time/timer.c:677 [inline]
del_timer+0x7c/0x179 kernel/time/timer.c:1034
try_to_grab_pending+0x81/0x2e5 kernel/workqueue.c:1230
cancel_delayed_work+0x7c/0x1c4 kernel/workqueue.c:2929
l2cap_clear_timer+0x1e/0x41 include/net/bluetooth/l2cap.h:834
l2cap_chan_del+0x2d8/0x37e net/bluetooth/l2cap_core.c:640
l2cap_chan_close+0x532/0x5d8 net/bluetooth/l2cap_core.c:756
l2cap_sock_shutdown+0x806/0x969 net/bluetooth/l2cap_sock.c:1174
l2cap_sock_release+0x64/0x14d net/bluetooth/l2cap_sock.c:1217
__sock_release+0xda/0x217 net/socket.c:580
sock_close+0x1b/0x1f net/socket.c:1039
__fput+0x322/0x55c fs/file_table.c:208
____fput+0x17/0x19 fs/file_table.c:244
task_work_run+0x19b/0x1d3 kernel/task_work.c:115
exit_task_work include/linux/task_work.h:21 [inline]
do_exit+0xe4c/0x204a kernel/exit.c:766
do_group_exit+0x291/0x291 kernel/exit.c:891
get_signal+0x749/0x1093 kernel/signal.c:2396
do_signal+0xa5/0xcdb arch/x86/kernel/signal.c:737
exit_to_usermode_loop arch/x86/entry/common.c:243 [inline]
prepare_exit_to_usermode+0xed/0x235 arch/x86/entry/common.c:277
syscall_return_slowpath+0x3a7/0x3b3 arch/x86/entry/common.c:348
int_ret_from_sys_call+0x25/0xa3
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+338f014a98367a08a114@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e127906b68 ]
Commit eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1980d37565 ]
(struct tipc_link_info)->dest is in network order (__be32), so we must
convert the value to network order before assigning. The problem detected
by sparse:
net/tipc/netlink_compat.c:699:24: warning: incorrect type in assignment (different base types)
net/tipc/netlink_compat.c:699:24: expected restricted __be32 [usertype] dest
net/tipc/netlink_compat.c:699:24: got int
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c48950b4 ]
This patch fixes the following message which randomly pops up during
glocktop call:
seq_file: buggy .next function table_seq_next did not update position index
The issue is that seq_read_iter() in fs/seq_file.c also needs an
increment of the index in an non next record case as well which this
patch fixes otherwise seq_read_iter() will print out the above message.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1df83992d9 upstream.
If the total number of commands queried through TPM2_CAP_COMMANDS is
different from that queried through TPM2_CC_GET_CAPABILITY, it indicates
an unknown error. In this case, an appropriate error code -EFAULT should
be returned. However, we currently do not explicitly assign this error
code to 'rc'. As a result, 0 was incorrectly returned.
Cc: stable@vger.kernel.org
Fixes: 58472f5cd4f6("tpm: validate TPM 2.0 commands")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34e5b01186 upstream.
As Or Cohen described:
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
This patch is to fix it by moving the auto_asconf init out of
sctp_init_sock(), by which inet_create()/inet6_create() won't
need to operate it in sctp_destroy_sock() when calling
sk_common_release().
It also makes more sense to do auto_asconf init while binding the
first addr, as auto_asconf actually requires an ANY addr bind,
see it in sctp_addr_wq_timeout_handler().
This addresses CVE-2021-23133.
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bfe5e8e4 upstream.
This reverts commit b166a20b07.
This one has to be reverted as it introduced a dead lock, as
syzbot reported:
CPU0 CPU1
---- ----
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
CPU0 is the thread of sctp_addr_wq_timeout_handler(), and CPU1
is that of sctp_close().
The original issue this commit fixed will be fixed in the next
patch.
Reported-by: syzbot+959223586843e69a2674@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1139aeb1c5 upstream.
As of commit 966a967116 ("smp: Avoid using two cache lines for struct
call_single_data"), the smp code prefers 32-byte aligned call_single_data
objects for performance reasons, but the block layer includes an instance
of this structure in the main 'struct request' that is more senstive
to size than to performance here, see 4ccafe0320 ("block: unalign
call_single_data in struct request").
The result is a violation of the calling conventions that clang correctly
points out:
block/blk-mq.c:630:39: warning: passing 8-byte aligned argument to 32-byte aligned parameter 2 of 'smp_call_function_single_async' may result in an unaligned pointer access [-Walign-mismatch]
smp_call_function_single_async(cpu, &rq->csd);
It does seem that the usage of the call_single_data without cache line
alignment should still be allowed by the smp code, so just change the
function prototype so it accepts both, but leave the default alignment
unchanged for the other users. This seems better to me than adding
a local hack to shut up an otherwise correct warning in the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.kernel.org/r/20210505211300.3174456-1-arnd@kernel.org
[nc: Fix conflicts]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 926ee00ea2 ]
The intent with this code was to return negative error codes but instead
it returns positives.
The problem is how type promotion works with ternary operations. These
functions return long, "ret" is an int and "copied" is a u32. The
negative error code is first cast to u32 so it becomes a high positive and
then cast to long where it's still a positive.
We could fix this by declaring "ret" as a ssize_t but let's just get rid
of the ternaries instead.
Link: https://lkml.kernel.org/r/YIE+/cK1tBzSuQPU@mwanda
Fixes: 5bf2b19320 ("kfifo: add example files to the kernel sample directory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7525858679 ]
In digital_tg_recv_dep_req, it calls nfc_tm_data_received(..,resp).
If nfc_tm_data_received() failed, the callee will free the resp via
kfree_skb() and return error. But in the exit branch, the resp
will be freed again.
My patch sets resp to NULL if nfc_tm_data_received() failed, to
avoid the double free.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d72e7c767 ]
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd9a40fd6 ]
When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d0 ("ath9k: Check for errors when reading SREV register")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83b8aa520 ]
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16edc99d6 ]
VMCI feature is not supported in conjunction with the vSphere Fault
Tolerance (FT) feature.
VMware Tools can repeatedly try to create a vsock connection. If FT is
enabled the kernel logs is flooded with the following messages:
qp_alloc_hypercall result = -20
Could not attach to queue pair with -20
"qp_alloc_hypercall result = -20" was hidden by commit e8266c4c33
("VMCI: Stop log spew when qp allocation isn't possible"), but "Could
not attach to queue pair with -20" is still there flooding the log.
Since the error message can be useful in some cases, print it only once.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e083ee8e ]
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92dfb27240 ]
While adding the invalid IRQ check after calling platform_get_irq(),
I managed to overlook that the driver has a complex error path in its
probe() method, thus a simple *return* couldn't be used. Use a proper
*goto* instead!
Fixes: e5b2e3e742 ("i2c: sh7760: add IRQ check")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fb0bedb5 ]
The signal strength of 5G is quite low, so user can't connect to an AP far
away. New parameters with new format and its parser are updated by the commit
84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser."), but
some parameters are missing. Use this commit to update to the novel parameters
that use new format.
Fixes: 84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219052607.7323-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38d0b1c9ce ]
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecb9dc158 ]
Mirror commit aeba3731b1 ("powerpc/pci: Fix IO space breakage after
of_pci_range_to_resource() change").
Most MIPS platforms do not define PCI_IOBASE, nor implement
pci_address_to_pio(). Moreover, IO_SPACE_LIMIT is 0xffff for most MIPS
platforms. of_pci_range_to_resource passes the _start address_ of the IO
range into pci_address_to_pio, which then checks it against
IO_SPACE_LIMIT and fails, because for MIPS platforms that use
pci-legacy (pci-lantiq, pci-rt3883, pci-mt7620), IO ranges start much
higher than 0xffff.
In fact, pci-mt7621 in staging already works around this problem, see
commit 09dd629eea ("staging: mt7621-pci: fix io space and properly set
resource limits")
So just stop using of_pci_range_to_resource, which does not work for
MIPS.
Fixes PCI errors like:
pci_bus 0000:00: root bus resource [io 0xffffffff]
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5b2e3e742 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: a26c20b1fa ("i2c: Renesas SH7760 I2C master driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e5f7a8d9 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb6129c328 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: 5faf6e1f58 ("i2c: emev2: add driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5581c2c5d0 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e701a25840 ]
The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 4863dea3fa ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87fce88658 ]
Currently the expression ~nic_conf1 is always true because nic_conf1
is a u16 and according to 6.5.3.3 of the C standard the ~ operator
promotes the u16 to an integer before flipping all the bits. Thus
the top 16 bits of the integer result are all set so the expression
is always true. If the intention was to flip all the bits of nic_conf1
then casting the integer result back to a u16 is a suitabel fix.
Interestingly static analyzers seem to thing a bitwise ! should be
used instead of ~ for this scenario, so I think the original intent
of the expression may need some extra consideration.
Addresses-Coverity: ("Logical vs. bitwise operator")
Fixes: c869f77d6a ("add mt7601u driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210225183241.1002129-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b27dadecdf ]
When neither CONFIG_PCI nor CONFIG_IBMVIO is set/enabled, iommu.c has a
build error. The fault injection code is not useful in that kernel config,
so make the FAIL_IOMMU option depend on PCI || IBMVIO.
Prevents this build error (warning escalated to error):
../arch/powerpc/kernel/iommu.c:178:30: error: 'fail_iommu_bus_notifier' defined but not used [-Werror=unused-variable]
178 | static struct notifier_block fail_iommu_bus_notifier = {
Fixes: d6b9a81b2a ("powerpc: IOMMU fault injection")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210404192623.10697-1-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10f8f96179 ]
The power PMU group constraints includes check for EBB events to make
sure all events in a group must agree on EBB. This will prevent
scheduling EBB and non-EBB events together. But in the existing check,
settings for constraint mask and value is interchanged. Patch fixes the
same.
Before the patch, PMU selftest "cpu_event_pinned_vs_ebb_test" fails with
below in dmesg logs. This happens because EBB event gets enabled along
with a non-EBB cpu event.
[35600.453346] cpu_event_pinne[41326]: illegal instruction (4)
at 10004a18 nip 10004a18 lr 100049f8 code 1 in
cpu_event_pinned_vs_ebb_test[10000000+10000]
Test results after the patch:
$ ./pmu/ebb/cpu_event_pinned_vs_ebb_test
test: cpu_event_pinned_vs_ebb
tags: git_version:v5.12-rc5-93-gf28c3125acd3-dirty
Binding to cpu 8
EBB Handler is at 0x100050c8
read error on event 0x7fffe6bd4040!
PM_RUN_INST_CMPL: result 9872 running/enabled 37930432
success: cpu_event_pinned_vs_ebb
This bug was hidden by other logic until commit 1908dc9117 (perf:
Tweak perf_event_attr::exclusive semantics).
Fixes: 4df4899911 ("powerpc/perf: Add power8 EBB support")
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
[mpe: Mention commit 1908dc9117]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1617725761-1464-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 298b58f00c ]
The macro CN23XX_PEM_BAR1_INDEX_REG is being used to shift oct->pcie_port
(a u16) left 24 places. There are two subtle issues here, first the
shift gets promoted to an signed int and then sign extended to a u64.
If oct->pcie_port is 0x80 or more then the upper bits get sign extended
to 1. Secondly shfiting a u16 24 bits will lead to an overflow so it
needs to be cast to a u64 for all the bits to not overflow.
It is entirely possible that the u16 port value is never large enough
for this to fail, but it is useful to fix unintended overflows such
as this.
Fix this by casting the port parameter to the macro to a u64 before
the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 5bc67f587b ("liquidio: CN23XX register definitions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fb45414ae ]
There are a few calls of usb_driver_claim_interface() but all of those
miss the proper error checks, as reported by Coverity. This patch
adds those missing checks.
Along with it, replace the magic pointer with -1 with a constant
USB_AUDIO_IFACE_UNUSED for better readability.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1475943 ("Error handling issues")
Addresses-Coverity-ID: 1475944 ("Error handling issues")
Addresses-Coverity-ID: 1475945 ("Error handling issues")
Fixes: b1ce7ba619 ("ALSA: usb-audio: claim autodetected PCM interfaces all at once")
Fixes: e5779998bf ("ALSA: usb-audio: refactor code")
Link: https://lore.kernel.org/r/202104051059.FB7F3016@keescook
Link: https://lore.kernel.org/r/20210406113534.30455-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca4d4c34ae ]
If the "type_a->nfcid_len" is too large then it would lead to memory
corruption in pn533_target_found_type_a() when we do:
memcpy(nfc_tgt->nfcid1, tgt_type_a->nfcid_data, nfc_tgt->nfcid1_len);
Fixes: c3b1e1e8a7 ("NFC: Export NFCID1 from pn533")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fe529449d ]
When compiling the powerpc with the SMP disabled, it shows the issue:
arch/powerpc/kernel/watchdog.c: In function ‘watchdog_smp_panic’:
arch/powerpc/kernel/watchdog.c:177:4: error: implicit declaration of function ‘smp_send_nmi_ipi’; did you mean ‘smp_send_stop’? [-Werror=implicit-function-declaration]
177 | smp_send_nmi_ipi(c, wd_lockup_ipi, 1000000);
| ^~~~~~~~~~~~~~~~
| smp_send_stop
cc1: all warnings being treated as errors
make[2]: *** [scripts/Makefile.build:273: arch/powerpc/kernel/watchdog.o] Error 1
make[1]: *** [scripts/Makefile.build:534: arch/powerpc/kernel] Error 2
make: *** [Makefile:1980: arch/powerpc] Error 2
make: *** Waiting for unfinished jobs....
We found that powerpc used ipi to implement hardlockup watchdog, so the
HAVE_HARDLOCKUP_DETECTOR_ARCH should depend on the SMP.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Huang <chenhuang5@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210327094900.938555-1-chenhuang5@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ef1dd9c7e ]
If identical_pvr_fixup() is not inlined, there are two modpost warnings:
WARNING: modpost: vmlinux.o(.text+0x54e8): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:of_get_flat_dt_prop()
The function identical_pvr_fixup() references
the function __init of_get_flat_dt_prop().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of of_get_flat_dt_prop is wrong.
WARNING: modpost: vmlinux.o(.text+0x551c): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:identify_cpu()
The function identical_pvr_fixup() references
the function __init identify_cpu().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of identify_cpu is wrong.
identical_pvr_fixup() calls two functions marked as __init and is only
called by a function marked as __init so it should be marked as __init
as well. At the same time, remove the inline keywork as it is not
necessary to inline this function. The compiler is still free to do so
if it feels it is worthwhile since commit 889b3c1245 ("compiler:
remove CONFIG_OPTIMIZE_INLINING entirely").
Fixes: 14b3d926a2 ("[POWERPC] 4xx: update 440EP(x)/440GR(x) identical PVR issue workaround")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1316
Link: https://lore.kernel.org/r/20210302200829.2680663-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5acd0cfbfb ]
There are two "netif_running" checks in this driver. One is in
"lapbeth_xmit" and the other is in "lapbeth_rcv". They serve to make
sure that the LAPB APIs called in these functions are called before
"lapb_unregister" is called by the "ndo_stop" function.
However, these "netif_running" checks are unreliable, because it's
possible that immediately after "netif_running" returns true, "ndo_stop"
is called (which causes "lapb_unregister" to be called).
This patch adds locking to make sure "lapbeth_xmit" and "lapbeth_rcv" can
reliably check and ensure the netif is running while doing their work.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f567d6ef86 ]
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
Fixes: 81bb773fae ("HID: plantronics: Update to map volume up/down controls")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de5bc7b425 ]
dev_attr_show() calls _iommu_event_show() via an indirect call but
_iommu_event_show()'s type does not currently match the type of the
show() member in 'struct device_attribute', resulting in a Control Flow
Integrity violation.
$ cat /sys/devices/amd_iommu_1/events/mem_dte_hit
csource=0x0a
$ dmesg | grep "CFI failure"
[ 3526.735140] CFI failure (target: _iommu_event_show...):
Change _iommu_event_show() and 'struct amd_iommu_event_desc' to
'struct device_attribute' so that there is no more CFI violation.
Fixes: 7be6296fdd ("perf/x86/amd: AMD IOMMU Performance Counter PERF uncore PMU implementation")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210415001112.3024673-1-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c08b0f755 ]
If some of the allocations fail between the dev_set_name() and the
device_register() then the name will not be freed. Fix this by
moving dev_set_name() directly in front of the call to device_register().
Fixes: a2aa24734d ("HSI: Add common DT binding for HSI client devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917e498c6 ]
The ARR register is cleared unconditionally upon probing, after the maximum
value has been read. This initial condition is rather not intuitive, when
considering the counter child driver. It rather expects the maximum value
by default:
- The counter interface shows a zero value by default for 'ceiling'
attribute.
- Enabling the counter without any prior configuration makes it doesn't
count.
The reset value of ARR register is the maximum. So Choice here
is to backup it, and restore it then, instead of clearing its value.
It also fixes the initial condition seen by the counter driver.
Fixes: d0f949e220 ("mfd: Add STM32 Timers driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6b1340dc7 ]
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of num_parents that is an int type.
There is a potential infinite loop if num_parents is larger than
the u8 loop counter. Fix this by making the loop counter the same
type as num_parents. Also make num_parents an unsigned int to
match the return type of the call to clk_hw_get_num_parents.
Addresses-Coverity: ("Infinite loop")
Fixes: 734d82f4a6 ("clk: uniphier: add core support code for UniPhier clock driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210409090104.629722-1-colin.king@canonical.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5a1f8921d ]
There is a small race where the parent is NULL even though the kobj has
already been made visible in sysfs.
For instance the attribute_group is made visible in sysfs_create_files()
and the mdev_type_attr_show() does:
ret = attr->show(kobj, type->parent->dev, buf);
Which will crash on NULL parent. Move the parent setup to before the type
pointer leaves the stack frame.
Fixes: 7b96953bc6 ("vfio: Mediated device Core driver")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <2-v2-d36939638fc6+d54-vfio2_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6471a65fd ]
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
Fixes: f351b2d638 ("sata_mv: Support SoC controllers")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/51436f00-27a1-e20b-c21b-0e817e0a7c86@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e379b40cc0 ]
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking
code to pass the positive IRQ #s to ata_host_activate(), propagate errors
upstream, and treat IRQ0 as error, returning -EINVAL, as the libata code
treats 0 as an indication that polling should be used anyway...
Fixes: 0df0d0a0ea ("[libata] ARM: add ixp4xx PATA driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e8f404d5 ]
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking code
to pass the positive IRQ #s to ata_host_activate(), propagate upstream
-EPROBE_DEFER, and set up the driver to polling mode on (negative) errors
and IRQ0 (libata treats IRQ #0 as a polling mode anyway)...
Fixes: a480167b23 ("pata_arasan_cf: Adding support for arasan compact flash host controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dd3b8c9f5 ]
There are 2 bugs in the can_boost() function because of using
x86 insn decoder. Since the insn->opcode never has a prefix byte,
it can not find CS override prefix in it. And the insn->attr is
the attribute of the opcode, thus inat_is_address_size_prefix(
insn->attr) always returns false.
Fix those by checking each prefix bytes with for_each_insn_prefix
loop and getting the correct attribute for each prefix byte.
Also, this removes unlikely, because this is a slow path.
Fixes: a8d11cd071 ("kprobes/x86: Consolidate insn decoder users for copying code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/161666691162.1120877.2808435205294352583.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cde22fcc7 ]
Currently the chroma_flags and alpha_flags are being zero'd with a bit-wise
mask and the following statement should be bit-wise or'ing in the new flag
bits but instead is making a direct assignment. Fix this by using the |=
operator rather than an assignment.
Addresses-Coverity: ("Unused value")
Fixes: ef834f7836 ("[media] vivid: add the video capture and output parts")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77db0ec8b7 ]
When running in Azure, disks may be connected to a Linux VM with
read/write caching enabled. If a VM panics and issues a VMbus
UNLOAD request to Hyper-V, the response is delayed until all dirty
data in the disk cache is flushed. In extreme cases, this flushing
can take 10's of seconds, depending on the disk speed and the amount
of dirty data. If kdump is configured for the VM, the current 10 second
timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD
complete message may arrive well after the kdump kernel is already
running, causing problems. Note that no problem occurs if kdump is
not enabled because Hyper-V waits for the cache flush before doing
a reboot through the BIOS/UEFI code.
Fix this problem by increasing the timeout in vmbus_wait_for_unload()
to 100 seconds. Also output periodic messages so that if anyone is
watching the serial console, they won't think the VM is completely
hung.
Fixes: 911e1987ef ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2209ea556 ]
When KEXEC is disabled, the UV build fails:
arch/x86/platform/uv/uv_nmi.c:875:14: error: ‘uv_nmi_kexec_failed’ undeclared (first use in this function)
Since uv_nmi_kexec_failed is only defined in the KEXEC_CORE #ifdef branch,
this code cannot ever have been build tested:
if (main)
pr_err("UV: NMI kdump: KEXEC not supported in this kernel\n");
atomic_set(&uv_nmi_kexec_failed, 1);
Nor is this use possible in uv_handle_nmi():
atomic_set(&uv_nmi_kexec_failed, 0);
These bugs were introduced in this commit:
d0a9964e98: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Which added the uv_nmi_kexec_failed assignments to !KEXEC code, while making the
definition KEXEC-only - apparently without testing the !KEXEC case.
Instead of complicating the #ifdef maze, simplify the code by requiring X86_UV
to depend on KEXEC_CORE. This pattern is present in other architectures as well.
( We'll remove the untested, 7 years old !KEXEC complications from the file in a
separate commit. )
Fixes: d0a9964e98: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d21e5abd3a ]
pmc_plt_clk* clocks are used for ethernet controllers, so need to stay
turned on. This adds the affected board family to critclk_systems DMI
table, so the clocks are marked as CLK_CRITICAL and not turned off.
This replaces the previously listed boards with a match for the whole
device family CBxx63. CBxx63 matches only baytrail devices.
There are new affected boards that would otherwise need to be listed.
There are unaffected boards in the family, but having the clocks
turned on is not an issue.
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Link: https://lore.kernel.org/r/20210412133006.397679-1-linux-kernel-dev@beckhoff.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2954a6f12f ]
When CONFIG_QCOM_SCM is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/firmware/qcom_scm-smc.o: In function `__scm_smc_do_quirk':
qcom_scm-smc.c:(.text+0x36): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call':
qcom_scm-legacy.c:(.text+0xe2): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call_atomic':
qcom_scm-legacy.c:(.text+0x1f0): undefined reference to `__arm_smccc_smc'
Note that __arm_smccc_smc is defined when HAVE_ARM_SMCCC is y.
So add dependency on HAVE_ARM_SMCCC in QCOM_SCM configuration.
Fixes: 916f743da3 ("firmware: qcom: scm: Move the scm driver to drivers/firmware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210406094200.60952-1-heying24@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8b20868a ]
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Fix up the TIOCMGET, TIOCMSET and TIOCGICOUNT helpers which returned
-EINVAL when a tty driver did not implement the corresponding
operations.
Note that the TIOCMGET and TIOCMSET helpers predate git and do not get a
corresponding Fixes tag below.
Fixes: d281da7ff6 ("tty: Make tiocgicount a handler")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d09845e98a ]
Some kernel-internal ASYNC flags have been superseded by tty-port flags
and should no longer be used by kernel drivers.
Fix the misspelled "__KERNEL__" compile guards which failed their sole
purpose to break out-of-tree drivers that have not yet been updated.
Fixes: 5c0517fefc ("tty: core: Undefine ASYNC_* flags superceded by TTY_PORT* flags")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd5619582d ]
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7cae626ca ]
In adf_create_ring, if the callee adf_init_ring() failed, the callee will
free the ring->base_addr by dma_free_coherent() and return -EFAULT. Then
adf_create_ring will goto err and the ring->base_addr will be freed again
in adf_cleanup_ring().
My patch sets ring->base_addr to NULL after the first freed to avoid the
double free.
Fixes: a672a9dc87 ("crypto: qat - Intel(R) QAT transport code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bc6262c61 ]
All of the CPPC sysfs show functions are called via indirect call in
kobj_attr_show(), where they should be of type
ssize_t (*show)(struct kobject *kobj, struct kobj_attribute *attr, char *buf);
because that is the type of the ->show() member in
'struct kobj_attribute' but they are actually of type
ssize_t (*show)(struct kobject *kobj, struct attribute *attr, char *buf);
because of the ->show() member in 'struct cppc_attr', resulting in a
Control Flow Integrity violation [1].
$ cat /sys/devices/system/cpu/cpu0/acpi_cppc/highest_perf
3400
$ dmesg | grep "CFI failure"
[ 175.970559] CFI failure (target: show_highest_perf+0x0/0x8):
As far as I can tell, the only difference between 'struct cppc_attr'
and 'struct kobj_attribute' aside from the type of the attr parameter
is the type of the count parameter in the ->store() member (ssize_t vs.
size_t), which does not actually matter because all of these nodes are
read-only.
Eliminate 'struct cppc_attr' in favor of 'struct kobj_attribute' to fix
the violation.
[1]: https://lore.kernel.org/r/20210401233216.2540591-1-samitolvanen@google.com/
Fixes: 158c998ea4 ("ACPI / CPPC: add sysfs support to compute delivered performance")
Link: https://github.com/ClangBuiltLinux/linux/issues/1343
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0648c55e3a ]
Given that no validation of how much data the firmware loader read in
for a given segment truncated segment files would best case result in a
hash verification failure, without any indication of what went wrong.
Improve this by validating that the firmware loader did return the
amount of data requested.
Fixes: 445c2410a4 ("soc: qcom: mdt_loader: Use request_firmware_into_buf()")
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210107232526.716989-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794aaf0144 ]
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c6b305c1 ]
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the greybus implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: e68453ed28 ("greybus: uart-gb: now builds, more framework added")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407102334.32361-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9b9263a25 ]
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of riv->ieee80211->LinkDetectInfo.SlotNum
that is a u16 type. There is a potential infinite loop if SlotNum
is larger than the u8 loop counter. Fix this by making the loop
counter the same type as SlotNum.
Addresses-Coverity: ("Infinite loop")
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210407150308.496623-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 076de75de1 ]
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9a ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83dc1173d7 ]
The function adf_isr_resource_alloc() is not unwinding correctly in case
of error.
This patch fixes the error paths and propagate the errors to the caller.
Fixes: 7afa232e76 ("crypto: qat - Intel(R) QAT DH895xcc accelerator")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 755915fc28 ]
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8609f5cfdc ]
ADF_STATUS_PF_RUNNING is (only) used and checked by adf_vf2pf_shutdown()
before calling adf_iov_putmsg()->mutex_lock(vf2pf_lock), however the
vf2pf_lock is initialized in adf_dev_init(), which can fail and when it
fail, the vf2pf_lock is either not initialized or destroyed, a subsequent
use of vf2pf_lock will cause issue.
To fix this issue, only set this flag if adf_dev_init() returns 0.
[ 7.178404] BUG: KASAN: user-memory-access in __mutex_lock.isra.0+0x1ac/0x7c0
[ 7.180345] Call Trace:
[ 7.182576] mutex_lock+0xc9/0xd0
[ 7.183257] adf_iov_putmsg+0x118/0x1a0 [intel_qat]
[ 7.183541] adf_vf2pf_shutdown+0x4d/0x7b [intel_qat]
[ 7.183834] adf_dev_shutdown+0x172/0x2b0 [intel_qat]
[ 7.184127] adf_probe+0x5e9/0x600 [qat_dh895xccvf]
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: 25c6ffb249 ("crypto: qat - check if PF is running")
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbdbbe6d3e ]
Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:
[ 55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[ 55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[ 55.245843] <IRQ>
[ 55.245843] ? pch_udc_svc_data_out+0x160/0x160
Check if driver is present before calling ->setup().
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7189b3c119 ]
Currently, the late microcode loading mechanism checks whether any CPUs
are offlined, and, in such a case, aborts the load attempt.
However, this must be done before the kernel caches new microcode from
the filesystem. Otherwise, when offlined CPUs are onlined later, those
cores are going to be updated through the CPU hotplug notifier callback
with the new microcode, while CPUs previously onine will continue to run
with the older microcode.
For example:
Turn off one core (2 threads):
echo 0 > /sys/devices/system/cpu/cpu3/online
echo 0 > /sys/devices/system/cpu/cpu1/online
Install the ucode fails because a primary SMT thread is offline:
cp intel-ucode/06-8e-09 /lib/firmware/intel-ucode/
echo 1 > /sys/devices/system/cpu/microcode/reload
bash: echo: write error: Invalid argument
Turn the core back on
echo 1 > /sys/devices/system/cpu/cpu3/online
echo 1 > /sys/devices/system/cpu/cpu1/online
cat /proc/cpuinfo |grep microcode
microcode : 0x30
microcode : 0xde
microcode : 0x30
microcode : 0xde
The rationale for why the update is aborted when at least one primary
thread is offline is because even if that thread is soft-offlined
and idle, it will still have to participate in broadcasted MCE's
synchronization dance or enter SMM, and in both examples it will execute
instructions so it better have the same microcode revision as the other
cores.
[ bp: Heavily edit and extend commit message with the reasoning behind all
this. ]
Fixes: 30ec26da99 ("x86/microcode: Do not upload microcode if CPUs are offline")
Signed-off-by: Otavio Pontes <otavio.pontes@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lkml.kernel.org/r/20210319165515.9240-2-otavio.pontes@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19c234a14e ]
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A
If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A
Fixes: 74e656d6b0 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3db1d52466 ]
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-13-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f264c6f6ae ]
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8987efbb17 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: c61248afa8 ("ARM: dts: Add max77686 RTC interrupt to cros5250-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6368c6056 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6503c568e9 ]
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: eea6653aae ("ARM: dts: Enable PMIC interrupts for exynos4412-odroid-common")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212534.216197-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e004c3e67b ]
Currently the array gpmc_cs is indexed by cs before it cs is range checked
and the pointer read from this out-of-index read is dereferenced. Fix this
by performing the range check on cs before the read and the following
pointer dereference.
Addresses-Coverity: ("Negative array index read")
Fixes: 9ed7a776eb ("ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210223193821.17232-1-colin.king@canonical.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 50a318cc9b upstream.
The commit d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a121 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44bada2821 upstream.
store_regs_fmt2() has an ordering problem: first the guarded storage
facility is enabled on the local cpu, then preemption disabled, and
then the STGSC (store guarded storage controls) instruction is
executed.
If the process gets scheduled away between enabling the guarded
storage facility and before preemption is disabled, this might lead to
a special operation exception and therefore kernel crash as soon as
the process is scheduled back and the STGSC instruction is executed.
Fixes: 4e0b1ab72b ("KVM: s390: gs support for kvm guests")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Cc: <stable@vger.kernel.org> # 4.12
Link: https://lore.kernel.org/r/20210415080127.1061275-1-hca@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6b4fbd90b upstream.
Initialize MSR_TSC_AUX with CPU node information if RDTSCP or RDPID is
supported. This fixes a bug where vdso_read_cpunode() will read garbage
via RDPID if RDPID is supported but RDTSCP is not. While no known CPU
supports RDPID but not RDTSCP, both Intel's SDM and AMD's APM allow for
RDPID to exist without RDTSCP, e.g. it's technically a legal CPU model
for a virtual machine.
Note, technically MSR_TSC_AUX could be initialized if and only if RDPID
is supported since RDTSCP is currently not used to retrieve the CPU node.
But, the cost of the superfluous WRMSR is negigible, whereas leaving
MSR_TSC_AUX uninitialized is just asking for future breakage if someone
decides to utilize RDTSCP.
Fixes: a582c540ac ("x86/vdso: Use RDPID in preference to LSL when available")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210504225632.1532621-2-seanjc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit defce244b0 upstream.
The quirk entry for Uniwill ECS M31EI is with the PCI SSID device 0,
which means matching with all. That is, it's essentially equivalent
with SND_PCI_QUIRK_VENDOR(0x1584), which also matches with the
previous entry for Haier W18 applying the very same quirk.
Let's unify them with the single vendor-quirk entry.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210428112704.23967-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dbc2ccac5 upstream.
Currently the ioctl command RADEON_INFO_SI_BACKEND_ENABLED_MASK can
copy back uninitialised data in value_tmp that pointer *value points
to. This can occur when rdev->family is less than CHIP_BONAIRE and
less than CHIP_TAHITI. Fix this by adding in a missing -EINVAL
so that no invalid value is copied back to userspace.
Addresses-Coverity: ("Uninitialized scalar variable)
Cc: stable@vger.kernel.org # 3.13+
Fixes: 439a1cfffe ("drm/radeon: expose render backend mask to the userspace")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a4db2a603 upstream.
commit d3374825ce ("md: make devices disappear when they are no longer
needed.") introduced protection between mddev creating & removing. The
md_open shouldn't create mddev when all_mddevs list doesn't contain
mddev. With currently code logic, there will be very easy to trigger
soft lockup in non-preempt env.
This patch changes md_open returning from -ERESTARTSYS to -EBUSY, which
will break the infinitely retry when md_open enter racing area.
This patch is partly fix soft lockup issue, full fix needs mddev_find
is split into two functions: mddev_find & mddev_find_or_alloc. And
md_open should call new mddev_find (it only does searching job).
For more detail, please refer with Christoph's "split mddev_find" patch
in later commits.
*** env ***
kvm-qemu VM 2C1G with 2 iscsi luns
kernel should be non-preempt
*** script ***
about trigger every time with below script
```
1 node1="mdcluster1"
2 node2="mdcluster2"
3
4 mdadm -Ss
5 ssh ${node2} "mdadm -Ss"
6 wipefs -a /dev/sda /dev/sdb
7 mdadm -CR /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda \
/dev/sdb --assume-clean
8
9 for i in {1..10}; do
10 echo ==== $i ====;
11
12 echo "test ...."
13 ssh ${node2} "mdadm -A /dev/md0 /dev/sda /dev/sdb"
14 sleep 1
15
16 echo "clean ....."
17 ssh ${node2} "mdadm -Ss"
18 done
```
I use mdcluster env to trigger soft lockup, but it isn't mdcluster
speical bug. To stop md array in mdcluster env will do more jobs than
non-cluster array, which will leave enough time/gap to allow kernel to
run md_open.
*** stack ***
```
[ 884.226509] mddev_put+0x1c/0xe0 [md_mod]
[ 884.226515] md_open+0x3c/0xe0 [md_mod]
[ 884.226518] __blkdev_get+0x30d/0x710
[ 884.226520] ? bd_acquire+0xd0/0xd0
[ 884.226522] blkdev_get+0x14/0x30
[ 884.226524] do_dentry_open+0x204/0x3a0
[ 884.226531] path_openat+0x2fc/0x1520
[ 884.226534] ? seq_printf+0x4e/0x70
[ 884.226536] do_filp_open+0x9b/0x110
[ 884.226542] ? md_release+0x20/0x20 [md_mod]
[ 884.226543] ? seq_read+0x1d8/0x3e0
[ 884.226545] ? kmem_cache_alloc+0x18a/0x270
[ 884.226547] ? do_sys_open+0x1bd/0x260
[ 884.226548] do_sys_open+0x1bd/0x260
[ 884.226551] do_syscall_64+0x5b/0x1e0
[ 884.226554] entry_SYSCALL_64_after_hwframe+0x44/0xa9
```
*** rootcause ***
"mdadm -A" (or other array assemble commands) will start a daemon "mdadm
--monitor" by default. When "mdadm -Ss" is running, the stop action will
wakeup "mdadm --monitor". The "--monitor" daemon will immediately get
info from /proc/mdstat. This time mddev in kernel still exist, so
/proc/mdstat still show md device, which makes "mdadm --monitor" to open
/dev/md0.
The previously "mdadm -Ss" is removing action, the "mdadm --monitor"
open action will trigger md_open which is creating action. Racing is
happening.
```
<thread 1>: "mdadm -Ss"
md_release
mddev_put deletes mddev from all_mddevs
queue_work for mddev_delayed_delete
at this time, "/dev/md0" is still available for opening
<thread 2>: "mdadm --monitor ..."
md_open
+ mddev_find can't find mddev of /dev/md0, and create a new mddev and
| return.
+ trigger "if (mddev->gendisk != bdev->bd_disk)" and return
-ERESTARTSYS.
```
In non-preempt kernel, <thread 2> is occupying on current CPU. and
mddev_delayed_delete which was created in <thread 1> also can't be
schedule.
In preempt kernel, it can also trigger above racing. But kernel doesn't
allow one thread running on a CPU all the time. after <thread 2> running
some time, the later "mdadm -A" (refer above script line 13) will call
md_alloc to alloc a new gendisk for mddev. it will break md_open
statement "if (mddev->gendisk != bdev->bd_disk)" and return 0 to caller,
the soft lockup is broken.
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhao Heming <heming.zhao@suse.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65aa97c4d2 upstream.
Split mddev_find into a simple mddev_find that just finds an existing
mddev by the unit number, and a more complicated mddev_find that deals
with find or allocating a mddev.
This turns out to fix this bug reported by Zhao Heming.
----------------------------- snip ------------------------------
commit d3374825ce ("md: make devices disappear when they are no longer
needed.") introduced protection between mddev creating & removing. The
md_open shouldn't create mddev when all_mddevs list doesn't contain
mddev. With currently code logic, there will be very easy to trigger
soft lockup in non-preempt env.
commit aafe104aa9 upstream.
It was reported that a fix to the ring buffer recursion detection would
cause a hung machine when performing suspend / resume testing. The
following backtrace was extracted from debugging that case:
Call Trace:
trace_clock_global+0x91/0xa0
__rb_reserve_next+0x237/0x460
ring_buffer_lock_reserve+0x12a/0x3f0
trace_buffer_lock_reserve+0x10/0x50
__trace_graph_return+0x1f/0x80
trace_graph_return+0xb7/0xf0
? trace_clock_global+0x91/0xa0
ftrace_return_to_handler+0x8b/0xf0
? pv_hash+0xa0/0xa0
return_to_handler+0x15/0x30
? ftrace_graph_caller+0xa0/0xa0
? trace_clock_global+0x91/0xa0
? __rb_reserve_next+0x237/0x460
? ring_buffer_lock_reserve+0x12a/0x3f0
? trace_event_buffer_lock_reserve+0x3c/0x120
? trace_event_buffer_reserve+0x6b/0xc0
? trace_event_raw_event_device_pm_callback_start+0x125/0x2d0
? dpm_run_callback+0x3b/0xc0
? pm_ops_is_empty+0x50/0x50
? platform_get_irq_byname_optional+0x90/0x90
? trace_device_pm_callback_start+0x82/0xd0
? dpm_run_callback+0x49/0xc0
With the following RIP:
RIP: 0010:native_queued_spin_lock_slowpath+0x69/0x200
Since the fix to the recursion detection would allow a single recursion to
happen while tracing, this lead to the trace_clock_global() taking a spin
lock and then trying to take it again:
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* lock taken */
(something else gets traced by function graph tracer)
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* DEAD LOCK! */
Tracing should *never* block, as it can lead to strange lockups like the
above.
Restructure the trace_clock_global() code to instead of simply taking a
lock to update the recorded "prev_time" simply use it, as two events
happening on two different CPUs that calls this at the same time, really
doesn't matter which one goes first. Use a trylock to grab the lock for
updating the prev_time, and if it fails, simply try again the next time.
If it failed to be taken, that means something else is already updating
it.
Link: https://lkml.kernel.org/r/20210430121758.650b6e8a@gandalf.local.home
Cc: stable@vger.kernel.org
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Fixes: b02414c8f0 ("ring-buffer: Fix recursion protection transitions between interrupt context") # started showing the problem
Fixes: 14131f2f98 ("tracing: implement trace_clock_*() APIs") # where the bug happened
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212761
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3641762c1c upstream.
Before this commit lis3lv02d_get_pwron_wait() had a WARN_ONCE() to catch
a potential divide by 0. WARN macros should only be used to catch internal
kernel bugs and that is not the case here. We have been receiving a lot of
bug reports about kernel backtraces caused by this WARN.
The div value being checked comes from the lis3->odrs[] array. Which
is sized to be a power-of-2 matching the number of bits in lis3->odr_mask.
The only lis3 model where this array is not entirely filled with non zero
values. IOW the only model where we can hit the div == 0 check is the
3dc ("8 bits 3DC sensor") model:
int lis3_3dc_rates[16] = {0, 1, 10, 25, 50, 100, 200, 400, 1600, 5000};
Note the 0 value at index 0, according to the datasheet an odr index of 0
means "Power-down mode". HP typically uses a lis3 accelerometer for HDD
fall protection. What I believe is happening here is that on newer
HP devices, which only contain a SDD, the BIOS is leaving the lis3 device
powered-down since it is not used for HDD fall protection.
Note that the lis3_3dc_rates array initializer only specifies 10 values,
which matches the datasheet. So it also contains 6 zero values at the end.
Replace the WARN with a normal check, which treats an odr index of 0
as power-down and uses a normal dev_err() to report the error in case
odr index point past the initialized part of the array.
Fixes: 1510dd5954 ("lis3lv02d: avoid divide by zero due to unchecked")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=785814
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1817027
BugLink: https://bugs.centos.org/view.php?id=10720
Link: https://lore.kernel.org/r/20210217102501.31758-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f626ca6829 upstream.
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
For those systems the PCI BARs that request a mapping in the I/O space
have the length recorded in the corresponding PCI resource set to zero,
which makes it unassigned:
# lspci -s 0031:02:04.0 -v
0031:02:04.0 FDDI network controller: Digital Equipment Corporation PCI-to-PDQ Interface Chip [PFI] FDDI (DEFPA) (rev 02)
Subsystem: Digital Equipment Corporation FDDIcontroller/PCI (DEFPA)
Flags: bus master, medium devsel, latency 136, IRQ 57, NUMA node 8
Memory at 620c080020000 (32-bit, non-prefetchable) [size=128]
I/O ports at <unassigned> [disabled]
Memory at 620c080030000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Kernel driver in use: defxx
Kernel modules: defxx
#
Regardless the driver goes ahead and requests it (here observed with a
Raptor Talos II POWER9 system), resulting in an odd /proc/ioport entry:
# cat /proc/ioports
00000000-ffffffffffffffff : 0031:02:04.0
#
Furthermore, the system gets confused as the driver actually continues
and pokes at those locations, causing a flood of messages being output
to the system console by the underlying system firmware, like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
defxx 0031:02:04.0: enabling device (0140 -> 0142)
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010000
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
and so on and so on (possibly intermixed actually, as there's no locking
between the kernel and the firmware in console port access with this
particular system, but cleaned up above for clarity), and once some 10k
of such pairs of the latter two messages have been produced an interace
eventually shows up in a useless state:
0031:02:04.0: DEFPA at I/O addr = 0x0, IRQ = 57, Hardware addr = 00-00-00-00-00-00
This was not expected to happen as resource handling was added to the
driver a while ago, because it was not known at that time that a PCI
system would be possible that cannot assign port I/O resources, and
oddly enough `request_region' does not fail, which would have caught it.
Correct the problem then by checking for the length of zero for the CSR
resource and bail out gracefully refusing to register an interface if
that turns out to be the case, producing messages like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
0031:02:04.0: Cannot use I/O, no address set, aborting
0031:02:04.0: Recompile driver with "CONFIG_DEFXX_MMIO=y"
Keep the original check for the EISA MMIO resource as implemented,
because in that case the length is hardwired to 0x400 as a consequence
of how the compare/mask address decoding works in the ESIC chip and it
is only the base address that is set to zero if MMIO has been disabled
for the adapter in EISA configuration, which in turn could be a valid
bus address in a legacy-free system implementing PCI, especially for
port I/O.
Where the EISA MMIO resource has been disabled for the adapter in EISA
configuration this arrangement keeps producing messages like:
eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
00:05: Cannot use MMIO, no address set, aborting
00:05: Recompile driver with "CONFIG_DEFXX_MMIO=n"
00:05: Or run ECU and set adapter's MMIO location
with the last two lines now swapped for easier handling in the driver.
There is no need to check for and catch the case of a port I/O resource
not having been assigned for EISA as the adapter uses the slot-specific
I/O space, which gets assigned by how EISA has been specified and maps
directly to the particular slot an option card has been placed in. And
the EISA variant of the adapter has additional registers that are only
accessible via the port I/O space anyway.
While at it factor out the error message calls into helpers and fix an
argument order bug with the `pr_err' call now in `dfx_register_res_err'.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4d0438e56a ("defxx: Clean up DEFEA resource management")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e98b69700 upstream.
pci_fixup_irqs() used to call pcibios_map_irq on every PCI device, which
for RT2880 included bus 0 slot 0. After pci_fixup_irqs() got removed,
only slots/funcs with devices attached would be called. While arguably
the right thing, that left no chance for this driver to ever initialize
slot 0, effectively bricking PCI and USB on RT2880 devices such as the
Belkin F5D8235-4 v1.
Slot 0 configuration needs to happen after PCI bus enumeration, but
before any device at slot 0x11 (func 0 or 1) is talked to. That was
determined empirically by testing on a Belkin F5D8235-4 v1 device. A
minimal BAR 0 config write followed by read, then setting slot 0
PCI_COMMAND to MASTER | IO | MEMORY is all that seems to be required for
proper functionality.
Tested by ensuring that full- and high-speed USB devices get enumerated
on the Belkin F5D8235-4 v1 (with an out of tree DTS file from OpenWrt).
Fixes: 04c81c7293 ("MIPS: PCI: Replace pci_fixup_irqs() call with host bridge IRQ mapping hooks")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tobias Wolf <dev-NTEO@vplace.de>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c61760e694 upstream.
Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()")
and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
fixed a refcount leak bug in bind/connect but introduced a
use-after-free if the same local is assigned to 2 different sockets.
This can be triggered by the following simple program:
int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) );
addr.sa_family = AF_NFC;
addr.nfc_protocol = NFC_PROTO_NFC_DEP;
bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
close(sock1);
close(sock2);
Fix this by assigning NULL to llcp_sock->local after calling
nfc_llcp_local_put.
This addresses CVE-2021-23134.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reported-by: Nadav Markus <nmarkus@paloaltonetworks.com>
Fixes: c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2cb6b891a upstream.
There is a possible race condition vulnerability between issuing a HCI
command and removing the cont. Specifically, functions hci_req_sync()
and hci_dev_do_close() can race each other like below:
thread-A in hci_req_sync() | thread-B in hci_dev_do_close()
| hci_req_sync_lock(hdev);
test_bit(HCI_UP, &hdev->flags); |
... | test_and_clear_bit(HCI_UP, &hdev->flags)
hci_req_sync_lock(hdev); |
|
In this commit we alter the sequence in function hci_req_sync(). Hence,
the thread-A cannot issue th.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Cc: Marcel Holtmann <marcel@holtmann.org>
Fixes: 7c6a329e44 ("[Bluetooth] Fix regression from using default link policy")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b793acdca upstream.
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c4c8c9544 upstream.
hci_chan can be created in 2 places: hci_loglink_complete_evt() if
it is an AMP hci_chan, or l2cap_conn_add() otherwise. In theory,
Only AMP hci_chan should be removed by a call to
hci_disconn_loglink_complete_evt(). However, the controller might mess
up, call that function, and destroy an hci_chan which is not initiated
by hci_loglink_complete_evt().
This patch adds a verification that the destroyed hci_chan must have
been init'd by hci_loglink_complete_evt().
Example crash call trace:
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe3/0x144 lib/dump_stack.c:118
print_address_description+0x67/0x22a mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report mm/kasan/report.c:412 [inline]
kasan_report+0x251/0x28f mm/kasan/report.c:396
hci_send_acl+0x3b/0x56e net/bluetooth/hci_core.c:4072
l2cap_send_cmd+0x5af/0x5c2 net/bluetooth/l2cap_core.c:877
l2cap_send_move_chan_cfm_icid+0x8e/0xb1 net/bluetooth/l2cap_core.c:4661
l2cap_move_fail net/bluetooth/l2cap_core.c:5146 [inline]
l2cap_move_channel_rsp net/bluetooth/l2cap_core.c:5185 [inline]
l2cap_bredr_sig_cmd net/bluetooth/l2cap_core.c:5464 [inline]
l2cap_sig_channel net/bluetooth/l2cap_core.c:5799 [inline]
l2cap_recv_frame+0x1d12/0x51aa net/bluetooth/l2cap_core.c:7023
l2cap_recv_acldata+0x2ea/0x693 net/bluetooth/l2cap_core.c:7596
hci_acldata_packet net/bluetooth/hci_core.c:4606 [inline]
hci_rx_work+0x2bd/0x45e net/bluetooth/hci_core.c:4796
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
Allocated by task 38:
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0x8d/0x9a mm/kasan/kasan.c:553
kmem_cache_alloc_trace+0x102/0x129 mm/slub.c:2787
kmalloc include/linux/slab.h:515 [inline]
kzalloc include/linux/slab.h:709 [inline]
hci_chan_create+0x86/0x26d net/bluetooth/hci_conn.c:1674
l2cap_conn_add.part.0+0x1c/0x814 net/bluetooth/l2cap_core.c:7062
l2cap_conn_add net/bluetooth/l2cap_core.c:7059 [inline]
l2cap_connect_cfm+0x134/0x852 net/bluetooth/l2cap_core.c:7381
hci_connect_cfm+0x9d/0x122 include/net/bluetooth/hci_core.h:1404
hci_remote_ext_features_evt net/bluetooth/hci_event.c:4161 [inline]
hci_event_packet+0x463f/0x72fa net/bluetooth/hci_event.c:5981
hci_rx_work+0x197/0x45e net/bluetooth/hci_core.c:4791
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
Freed by task 1732:
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free mm/kasan/kasan.c:521 [inline]
__kasan_slab_free+0x106/0x128 mm/kasan/kasan.c:493
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook+0xaa/0xf6 mm/slub.c:1436
slab_free mm/slub.c:3009 [inline]
kfree+0x182/0x21e mm/slub.c:3972
hci_disconn_loglink_complete_evt net/bluetooth/hci_event.c:4891 [inline]
hci_event_packet+0x6a1c/0x72fa net/bluetooth/hci_event.c:6050
hci_rx_work+0x197/0x45e net/bluetooth/hci_core.c:4791
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
The buggy address belongs to the object at ffff8881d7af9180
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 24 bytes inside of
128-byte region [ffff8881d7af9180, ffff8881d7af9200)
The buggy address belongs to the page:
page:ffffea00075ebe40 count:1 mapcount:0 mapping:ffff8881da403200 index:0x0
flags: 0x8000000000000200(slab)
raw: 8000000000000200 dead000000000100 dead000000000200 ffff8881da403200
raw: 0000000000000000 0000000080150015 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881d7af9080: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8881d7af9100: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8881d7af9180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881d7af9200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881d7af9280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+98228e7407314d2d4ba2@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 262e6ae708 upstream.
If a TAINT_PROPRIETARY_MODULE exports symbol, inherit the taint flag
for all modules importing these symbols, and don't allow loading
symbols from TAINT_PROPRIETARY_MODULE modules if the module previously
imported gplonly symbols. Add a anti-circumvention devices so people
don't accidentally get themselves into trouble this way.
Comment from Greg:
"Ah, the proven-to-be-illegal "GPL Condom" defense :)"
[jeyu: pr_info -> pr_err and pr_warn as per discussion]
Link: http://lore.kernel.org/r/20200730162957.GA22469@lst.de
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e947c8f4a upstream.
When loading a device-mapper table for a request-based mapped device,
and the allocation/initialization of the blk_mq_tag_set for the device
fails, a following device remove will cause a double free.
E.g. (dmesg):
device-mapper: core: Cannot initialize queue for request-based dm-mq mapped device
device-mapper: ioctl: unable to set up device queue for new table.
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0305e098835de000 TEID: 0305e098835de803
Fault in home space mode while using kernel ASCE.
AS:000000025efe0007 R3:0000000000000024
Oops: 0038 ilc:3 [#1] SMP
Modules linked in: ... lots of modules ...
Supported: Yes, External
CPU: 0 PID: 7348 Comm: multipathd Kdump: loaded Tainted: G W X 5.3.18-53-default #1 SLE15-SP3
Hardware name: IBM 8561 T01 7I2 (LPAR)
Krnl PSW : 0704e00180000000 000000025e368eca (kfree+0x42/0x330)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 000000000000004a 000000025efe5230 c1773200d779968d 0000000000000000
000000025e520270 000000025e8d1b40 0000000000000003 00000007aae10000
000000025e5202a2 0000000000000001 c1773200d779968d 0305e098835de640
00000007a8170000 000003ff80138650 000000025e5202a2 000003e00396faa8
Krnl Code: 000000025e368eb8: c4180041e100 lgrl %r1,25eba50b8
000000025e368ebe: ecba06b93a55 risbg %r11,%r10,6,185,58
#000000025e368ec4: e3b010000008 ag %r11,0(%r1)
>000000025e368eca: e310b0080004 lg %r1,8(%r11)
000000025e368ed0: a7110001 tmll %r1,1
000000025e368ed4: a7740129 brc 7,25e369126
000000025e368ed8: e320b0080004 lg %r2,8(%r11)
000000025e368ede: b904001b lgr %r1,%r11
Call Trace:
[<000000025e368eca>] kfree+0x42/0x330
[<000000025e5202a2>] blk_mq_free_tag_set+0x72/0xb8
[<000003ff801316a8>] dm_mq_cleanup_mapped_device+0x38/0x50 [dm_mod]
[<000003ff80120082>] free_dev+0x52/0xd0 [dm_mod]
[<000003ff801233f0>] __dm_destroy+0x150/0x1d0 [dm_mod]
[<000003ff8012bb9a>] dev_remove+0x162/0x1c0 [dm_mod]
[<000003ff8012a988>] ctl_ioctl+0x198/0x478 [dm_mod]
[<000003ff8012ac8a>] dm_ctl_ioctl+0x22/0x38 [dm_mod]
[<000000025e3b11ee>] ksys_ioctl+0xbe/0xe0
[<000000025e3b127a>] __s390x_sys_ioctl+0x2a/0x40
[<000000025e8c15ac>] system_call+0xd8/0x2c8
Last Breaking-Event-Address:
[<000000025e52029c>] blk_mq_free_tag_set+0x6c/0xb8
Kernel panic - not syncing: Fatal exception: panic_on_oops
When allocation/initialization of the blk_mq_tag_set fails in
dm_mq_init_request_queue(), it is uninitialized/freed, but the pointer
is not reset to NULL; so when dev_remove() later gets into
dm_mq_cleanup_mapped_device() it sees the pointer and tries to
uninitialize and free it again.
Fix this by setting the pointer to NULL in dm_mq_init_request_queue()
error-handling. Also set it to NULL in dm_mq_cleanup_mapped_device().
Cc: <stable@vger.kernel.org> # 4.6+
Fixes: 1c357a1e86 ("dm: allocate blk_mq_tag_set rather than embed in mapped_device")
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 785e3c0a3a upstream.
The default max PID is set by PID_MAX_DEFAULT, and the tracing
infrastructure uses this number to map PIDs to the comm names of the
tasks, such output of the trace can show names from the recorded PIDs in
the ring buffer. This mapping is also exported to user space via the
"saved_cmdlines" file in the tracefs directory.
But currently the mapping expects the PIDs to be less than
PID_MAX_DEFAULT, which is the default maximum and not the real maximum.
Recently, systemd will increases the maximum value of a PID on the system,
and when tasks are traced that have a PID higher than PID_MAX_DEFAULT, its
comm is not recorded. This leads to the entire trace to have "<...>" as
the comm name, which is pretty useless.
Instead, keep the array mapping the size of PID_MAX_DEFAULT, but instead
of just mapping the index to the comm, map a mask of the PID
(PID_MAX_DEFAULT - 1) to the comm, and find the full PID from the
map_cmdline_to_pid array (that already exists).
This bug goes back to the beginning of ftrace, but hasn't been an issue
until user space started increasing the maximum value of PIDs.
Link: https://lkml.kernel.org/r/20210427113207.3c601884@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: bc0c38d139 ("ftrace: latency tracer infrastructure")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c560e76319 upstream.
The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.
Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55b74ce7d2 upstream.
Fixes bug with the handling of more than one language in
the string table in f_fs.c.
str_count was not reset for subsequent language codes.
str_count-- "rolls under" and processes u32 max strings on
the processing of the second language entry.
The existing bug can be reproduced by adding a second language table
to the structure "strings" in tools/usb/ffs-test.c.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Link: https://lore.kernel.org/r/20210317224109.21534-1-dean@sensoray.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43c4cab006 upstream.
Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().
Fixes: f5c61225cf ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a5d797a9f upstream.
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a149d2a5ca upstream.
Commit <50122847007> ("ext4: fix check to prevent initializing reserved
inodes") check the block group zero and prevent initializing reserved
inodes. But in some special cases, the reserved inode may not all belong
to the group zero, it may exist into the second group if we format
filesystem below.
mkfs.ext4 -b 4096 -g 8192 -N 1024 -I 4096 /dev/sda
So, it will end up triggering a false positive report of a corrupted
file system. This patch fix it by avoid check reserved inodes if no free
inode blocks will be zeroed.
Cc: stable@kernel.org
Fixes: 5012284700 ("ext4: fix check to prevent initializing reserved inodes")
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Suggested-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210331121516.2243099-1-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9af478c0 upstream.
# echo switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter
will cause switch_mm to stop tracing by the traceoff command.
# echo -n switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter
does nothing.
The reason is that the parsing in the write function only processes
commands if it finished parsing (there is white space written after the
command). That's to handle:
write(fd, "switch_mm:", 10);
write(fd, "traceoff", 8);
cases, where the command is broken over multiple writes.
The problem is if the file descriptor is closed, then the write call is
not processed, and the command needs to be processed in the release code.
The release code can handle matching of functions, but does not handle
commands.
Cc: stable@vger.kernel.org
Fixes: eda1e32855 ("tracing: handle broken names in ftrace filter")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fbf5d6837 upstream.
The FUTEX_WAIT operand has historically a relative timeout which means that
the clock id is irrelevant as relative timeouts on CLOCK_REALTIME are not
subject to wall clock changes and therefore are mapped by the kernel to
CLOCK_MONOTONIC for simplicity.
If a caller would set FUTEX_CLOCK_REALTIME for FUTEX_WAIT the timeout is
still treated relative vs. CLOCK_MONOTONIC and then the wait arms that
timeout based on CLOCK_REALTIME which is broken and obviously has never
been used or even tested.
Reject any attempt to use FUTEX_CLOCK_REALTIME with FUTEX_WAIT again.
The desired functionality can be achieved with FUTEX_WAIT_BITSET and a
FUTEX_BITSET_MATCH_ANY argument.
Fixes: 337f13046f ("futex: Allow FUTEX_CLOCK_REALTIME with FUTEX_WAIT op")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210422194704.834797921@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c6e405e1 upstream.
It seems like Fedora 34 ends up enabling a few new gcc warnings, notably
"-Wstringop-overread" and "-Warray-parameter".
Both of them cause what seem to be valid warnings in the kernel, where
we have array size mismatches in function arguments (that are no longer
just silently converted to a pointer to element, but actually checked).
This fixes most of the trivial ones, by making the function declaration
match the function definition, and in the case of intel_pm.c, removing
the over-specified array size from the argument declaration.
At least one 'stringop-overread' warning remains in the i915 driver, but
that one doesn't have the same obvious trivial fix, and may or may not
actually be indicative of a bug.
[ It was a mistake to upgrade one of my machines to Fedora 34 while
being busy with the merge window, but if this is the extent of the
compiler upgrade problems, things are better than usual - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrey Zhizhikin <andrey.z@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82e5d8cc76 upstream.
gcc-11 introdces a harmless warning for cap_inode_getsecurity:
security/commoncap.c: In function ‘cap_inode_getsecurity’:
security/commoncap.c:440:33: error: ‘memcpy’ reading 16 bytes from a region of size 0 [-Werror=stringop-overread]
440 | memcpy(&nscap->data, &cap->data, sizeof(__le32) * 2 * VFS_CAP_U32);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem here is that tmpbuf is initialized to NULL, so gcc assumes
it is not accessible unless it gets set by vfs_getxattr_alloc(). This is
a legitimate warning as far as I can tell, but the code is correct since
it correctly handles the error when that function fails.
Add a separate NULL check to tell gcc about it as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: James Morris <jamorris@linux.microsoft.com>
Cc: Andrey Zhizhikin <andrey.z@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2417b9869b upstream.
This patch addresses a data corruption bug in raid1 arrays using bitmaps.
Without this fix, the bitmap bits for the failed I/O end up being cleared.
Since we are in the failure leg of raid1_end_write_request, the request
either needs to be retried (R1BIO_WriteError) or failed (R1BIO_Degraded).
Fixes: eeba6809d8 ("md/raid1: end bio when the device faulty")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Paul Clements <paul.clements@us.sios.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7de21e679e upstream.
A few archs like powerpc have different errno.h values for macros
EDEADLOCK and EDEADLK. In code including both libc and linux versions of
errno.h, this can result in multiple definitions of EDEADLOCK in the
include chain. Definitions to the same value (e.g. seen with mips) do
not raise warnings, but on powerpc there are redefinitions changing the
value, which raise warnings and errors (if using "-Werror").
Guard against these redefinitions to avoid build errors like the following,
first seen cross-compiling libbpf v5.8.9 for powerpc using GCC 8.4.0 with
musl 1.1.24:
In file included from ../../arch/powerpc/include/uapi/asm/errno.h:5,
from ../../include/linux/err.h:8,
from libbpf.c:29:
../../include/uapi/asm-generic/errno.h:40: error: "EDEADLOCK" redefined [-Werror]
#define EDEADLOCK EDEADLK
In file included from toolchain-powerpc_8540_gcc-8.4.0_musl/include/errno.h:10,
from libbpf.c:26:
toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/errno.h:58: note: this is the location of the previous definition
#define EDEADLOCK 58
cc1: all warnings being treated as errors
Cc: Stable <stable@vger.kernel.org>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200917135437.1238787-1-Tony.Ambardar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ae5bc12d0 upstream.
During the EEH MMIO error checking, the current implementation fails to map
the (virtual) MMIO address back to the pci device on radix with hugepage
mappings for I/O. This results into failure to dispatch EEH event with no
recovery even when EEH capability has been enabled on the device.
eeh_check_failure(token) # token = virtual MMIO address
addr = eeh_token_to_phys(token);
edev = eeh_addr_cache_get_dev(addr);
if (!edev)
return 0;
eeh_dev_check_failure(edev); <= Dispatch the EEH event
In case of hugepage mappings, eeh_token_to_phys() has a bug in virt -> phys
translation that results in wrong physical address, which is then passed to
eeh_addr_cache_get_dev() to match it against cached pci I/O address ranges
to get to a PCI device. Hence, it fails to find a match and the EEH event
never gets dispatched leaving the device in failed state.
The commit 3343962068 ("powerpc/eeh: Handle hugepages in ioremap space")
introduced following logic to translate virt to phys for hugepage mappings:
eeh_token_to_phys():
+ pa = pte_pfn(*ptep);
+
+ /* On radix we can do hugepage mappings for io, so handle that */
+ if (hugepage_shift) {
+ pa <<= hugepage_shift; <= This is wrong
+ pa |= token & ((1ul << hugepage_shift) - 1);
+ }
This patch fixes the virt -> phys translation in eeh_token_to_phys()
function.
$ cat /sys/kernel/debug/powerpc/eeh_address_cache
mem addr range [0x0000040080000000-0x00000400807fffff]: 0030:01:00.1
mem addr range [0x0000040080800000-0x0000040080ffffff]: 0030:01:00.1
mem addr range [0x0000040081000000-0x00000400817fffff]: 0030:01:00.0
mem addr range [0x0000040081800000-0x0000040081ffffff]: 0030:01:00.0
mem addr range [0x0000040082000000-0x000004008207ffff]: 0030:01:00.1
mem addr range [0x0000040082080000-0x00000400820fffff]: 0030:01:00.0
mem addr range [0x0000040082100000-0x000004008210ffff]: 0030:01:00.1
mem addr range [0x0000040082110000-0x000004008211ffff]: 0030:01:00.0
Above is the list of cached io address ranges of pci 0030:01:00.<fn>.
Before this patch:
Tracing 'arg1' of function eeh_addr_cache_get_dev() during error injection
clearly shows that 'addr=' contains wrong physical address:
kworker/u16:0-7 [001] .... 108.883775: eeh_addr_cache_get_dev:
(eeh_addr_cache_get_dev+0xc/0xf0) addr=0x80103000a510
dmesg shows no EEH recovery messages:
[ 108.563768] bnx2x: [bnx2x_timer:5801(eth2)]MFW seems hanged: drv_pulse (0x9ae) != mcp_pulse (0x7fff)
[ 108.563788] bnx2x: [bnx2x_hw_stats_update:870(eth2)]NIG timer max (4294967295)
[ 108.883788] bnx2x: [bnx2x_acquire_hw_lock:2013(eth1)]lock_status 0xffffffff resource_bit 0x1
[ 108.884407] bnx2x 0030:01:00.0 eth1: MDC/MDIO access timeout
[ 108.884976] bnx2x 0030:01:00.0 eth1: MDC/MDIO access timeout
<..>
After this patch:
eeh_addr_cache_get_dev() trace shows correct physical address:
<idle>-0 [001] ..s. 1043.123828: eeh_addr_cache_get_dev:
(eeh_addr_cache_get_dev+0xc/0xf0) addr=0x40080bc7cd8
dmesg logs shows EEH recovery getting triggerred:
[ 964.323980] bnx2x: [bnx2x_timer:5801(eth2)]MFW seems hanged: drv_pulse (0x746f) != mcp_pulse (0x7fff)
[ 964.323991] EEH: Recovering PHB#30-PE#10000
[ 964.324002] EEH: PE location: N/A, PHB location: N/A
[ 964.324006] EEH: Frozen PHB#30-PE#10000 detected
<..>
Fixes: 3343962068 ("powerpc/eeh: Handle hugepages in ioremap space")
Cc: stable@vger.kernel.org # v5.3+
Reported-by: Dominic DeMarco <ddemarc@us.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/161821396263.48361.2796709239866588652.stgit@jupiter
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 960b9a8a76 upstream.
KASAN report a slab-out-of-bounds problem. The logs are listed below.
It is because in function jffs2_scan_dirent_node, we alloc "checkedlen+1"
bytes for fd->name and we check crc with length rd->nsize. If checkedlen
is less than rd->nsize, it will cause the slab-out-of-bounds problem.
jffs2: Dirent at *** has zeroes in name. Truncating to %d char
==================================================================
BUG: KASAN: slab-out-of-bounds in crc32_le+0x1ce/0x260 at addr ffff8800842cf2d1
Read of size 1 by task test_JFFS2/915
=============================================================================
BUG kmalloc-64 (Tainted: G B O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in jffs2_alloc_full_dirent+0x2a/0x40 age=0 cpu=1 pid=915
___slab_alloc+0x580/0x5f0
__slab_alloc.isra.24+0x4e/0x64
__kmalloc+0x170/0x300
jffs2_alloc_full_dirent+0x2a/0x40
jffs2_scan_eraseblock+0x1ca4/0x3b64
jffs2_scan_medium+0x285/0xfe0
jffs2_do_mount_fs+0x5fb/0x1bbc
jffs2_do_fill_super+0x245/0x6f0
jffs2_fill_super+0x287/0x2e0
mount_mtd_aux.isra.0+0x9a/0x144
mount_mtd+0x222/0x2f0
jffs2_mount+0x41/0x60
mount_fs+0x63/0x230
vfs_kern_mount.part.6+0x6c/0x1f4
do_mount+0xae8/0x1940
SyS_mount+0x105/0x1d0
INFO: Freed in jffs2_free_full_dirent+0x22/0x40 age=27 cpu=1 pid=915
__slab_free+0x372/0x4e4
kfree+0x1d4/0x20c
jffs2_free_full_dirent+0x22/0x40
jffs2_build_remove_unlinked_inode+0x17a/0x1e4
jffs2_do_mount_fs+0x1646/0x1bbc
jffs2_do_fill_super+0x245/0x6f0
jffs2_fill_super+0x287/0x2e0
mount_mtd_aux.isra.0+0x9a/0x144
mount_mtd+0x222/0x2f0
jffs2_mount+0x41/0x60
mount_fs+0x63/0x230
vfs_kern_mount.part.6+0x6c/0x1f4
do_mount+0xae8/0x1940
SyS_mount+0x105/0x1d0
entry_SYSCALL_64_fastpath+0x1e/0x97
Call Trace:
[<ffffffff815befef>] dump_stack+0x59/0x7e
[<ffffffff812d1d65>] print_trailer+0x125/0x1b0
[<ffffffff812d82c8>] object_err+0x34/0x40
[<ffffffff812dadef>] kasan_report.part.1+0x21f/0x534
[<ffffffff81132401>] ? vprintk+0x2d/0x40
[<ffffffff815f1ee2>] ? crc32_le+0x1ce/0x260
[<ffffffff812db41a>] kasan_report+0x26/0x30
[<ffffffff812d9fc1>] __asan_load1+0x3d/0x50
[<ffffffff815f1ee2>] crc32_le+0x1ce/0x260
[<ffffffff814764ae>] ? jffs2_alloc_full_dirent+0x2a/0x40
[<ffffffff81485cec>] jffs2_scan_eraseblock+0x1d0c/0x3b64
[<ffffffff81488813>] ? jffs2_scan_medium+0xccf/0xfe0
[<ffffffff81483fe0>] ? jffs2_scan_make_ino_cache+0x14c/0x14c
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff812d5d90>] ? kmem_cache_alloc_trace+0x10c/0x2cc
[<ffffffff818169fb>] ? mtd_point+0xf7/0x130
[<ffffffff81487dc9>] jffs2_scan_medium+0x285/0xfe0
[<ffffffff81487b44>] ? jffs2_scan_eraseblock+0x3b64/0x3b64
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff812d57df>] ? __kmalloc+0x12b/0x300
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff814a2753>] ? jffs2_sum_init+0x9f/0x240
[<ffffffff8148b2ff>] jffs2_do_mount_fs+0x5fb/0x1bbc
[<ffffffff8148ad04>] ? jffs2_del_noinode_dirent+0x640/0x640
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff81127c5b>] ? __init_rwsem+0x97/0xac
[<ffffffff81492349>] jffs2_do_fill_super+0x245/0x6f0
[<ffffffff81493c5b>] jffs2_fill_super+0x287/0x2e0
[<ffffffff814939d4>] ? jffs2_parse_options+0x594/0x594
[<ffffffff81819bea>] mount_mtd_aux.isra.0+0x9a/0x144
[<ffffffff81819eb6>] mount_mtd+0x222/0x2f0
[<ffffffff814939d4>] ? jffs2_parse_options+0x594/0x594
[<ffffffff81819c94>] ? mount_mtd_aux.isra.0+0x144/0x144
[<ffffffff81258757>] ? free_pages+0x13/0x1c
[<ffffffff814fa0ac>] ? selinux_sb_copy_data+0x278/0x2e0
[<ffffffff81492b35>] jffs2_mount+0x41/0x60
[<ffffffff81302fb7>] mount_fs+0x63/0x230
[<ffffffff8133755f>] ? alloc_vfsmnt+0x32f/0x3b0
[<ffffffff81337f2c>] vfs_kern_mount.part.6+0x6c/0x1f4
[<ffffffff8133ceec>] do_mount+0xae8/0x1940
[<ffffffff811b94e0>] ? audit_filter_rules.constprop.6+0x1d10/0x1d10
[<ffffffff8133c404>] ? copy_mount_string+0x40/0x40
[<ffffffff812cbf78>] ? alloc_pages_current+0xa4/0x1bc
[<ffffffff81253a89>] ? __get_free_pages+0x25/0x50
[<ffffffff81338993>] ? copy_mount_options.part.17+0x183/0x264
[<ffffffff8133e3a9>] SyS_mount+0x105/0x1d0
[<ffffffff8133e2a4>] ? copy_mnt_ns+0x560/0x560
[<ffffffff810e8391>] ? msa_space_switch_handler+0x13d/0x190
[<ffffffff81be184a>] entry_SYSCALL_64_fastpath+0x1e/0x97
[<ffffffff810e9274>] ? msa_space_switch+0xb0/0xe0
Memory state around the buggy address:
ffff8800842cf180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8800842cf200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8800842cf280: fc fc fc fc fc fc 00 00 00 00 01 fc fc fc fc fc
^
ffff8800842cf300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8800842cf380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Cc: stable@vger.kernel.org
Reported-by: Kunkun Xu <xukunkun1@huawei.com>
Signed-off-by: lizhe <lizhe67@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de144ff423 upstream.
If the pNFS layout segment is marked with the NFS_LSEG_LAYOUTRETURN
flag, then the assumption is that it has some reporting requirement
to perform through a layoutreturn (e.g. flexfiles layout stats or error
information).
Fixes: 6d597e1750 ("pnfs: only tear down lsegs that precede seqid in LAYOUTRETURN args")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 388708028e ]
The arm64 assembler in binutils 2.32 and above generates a program
property note in a note section, .note.gnu.property, to encode used x86
ISAs and features. But the kernel linker script only contains a single
NOTE segment:
PHDRS
{
text PT_LOAD FLAGS(5) FILEHDR PHDRS; /* PF_R|PF_X */
dynamic PT_DYNAMIC FLAGS(4); /* PF_R */
note PT_NOTE FLAGS(4); /* PF_R */
}
The NOTE segment generated by the vDSO linker script is aligned to 4 bytes.
But the .note.gnu.property section must be aligned to 8 bytes on arm64.
$ readelf -n vdso64.so
Displaying notes found in: .note
Owner Data size Description
Linux 0x00000004 Unknown note type: (0x00000000)
description data: 06 00 00 00
readelf: Warning: note with invalid namesz and/or descsz found at offset 0x20
readelf: Warning: type: 0x78, namesize: 0x00000100, descsize: 0x756e694c, alignment: 8
Since the note.gnu.property section in the vDSO is not checked by the
dynamic linker, discard the .note.gnu.property sections in the vDSO.
Similar to commit 4caffe6a28 ("x86/vdso: Discard .note.gnu.property
sections in vDSO"), but for arm64.
Signed-off-by: Bill Wendling <morbo@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210423205159.830854-1-morbo@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9690f426b ]
Commit dbcc7d57bf ("btrfs: fix race when cloning extent buffer during
rewind of an old root"), fixed a race when we need to rewind the extent
buffer of an old root. It was caused by picking a new mod log operation
for the extent buffer while getting a cloned extent buffer with an outdated
number of items (off by -1), because we cloned the extent buffer without
locking it first.
However there is still another similar race, but in the opposite direction.
The cloned extent buffer has a number of items that does not match the
number of tree mod log operations that are going to be replayed. This is
because right after we got the last (most recent) tree mod log operation to
replay and before locking and cloning the extent buffer, another task adds
a new pointer to the extent buffer, which results in adding a new tree mod
log operation and incrementing the number of items in the extent buffer.
So after cloning we have mismatch between the number of items in the extent
buffer and the number of mod log operations we are going to apply to it.
This results in hitting a BUG_ON() that produces the following stack trace:
------------[ cut here ]------------
kernel BUG at fs/btrfs/tree-mod-log.c:675!
invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 3 PID: 4811 Comm: crawl_1215 Tainted: G W 5.12.0-7d1efdf501f8-misc-next+ #99
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:tree_mod_log_rewind+0x3b1/0x3c0
Code: 05 48 8d 74 10 (...)
RSP: 0018:ffffc90001027090 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff8880a8514600 RCX: ffffffffaa9e59b6
RDX: 0000000000000007 RSI: dffffc0000000000 RDI: ffff8880a851462c
RBP: ffffc900010270e0 R08: 00000000000000c0 R09: ffffed1004333417
R10: ffff88802199a0b7 R11: ffffed1004333416 R12: 000000000000000e
R13: ffff888135af8748 R14: ffff88818766ff00 R15: ffff8880a851462c
FS: 00007f29acf62700(0000) GS:ffff8881f2200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0e6013f718 CR3: 000000010d42e003 CR4: 0000000000170ee0
Call Trace:
btrfs_get_old_root+0x16a/0x5c0
? lock_downgrade+0x400/0x400
btrfs_search_old_slot+0x192/0x520
? btrfs_search_slot+0x1090/0x1090
? free_extent_buffer.part.61+0xd7/0x140
? free_extent_buffer+0x13/0x20
resolve_indirect_refs+0x3e9/0xfc0
? lock_downgrade+0x400/0x400
? __kasan_check_read+0x11/0x20
? add_prelim_ref.part.11+0x150/0x150
? lock_downgrade+0x400/0x400
? __kasan_check_read+0x11/0x20
? lock_acquired+0xbb/0x620
? __kasan_check_write+0x14/0x20
? do_raw_spin_unlock+0xa8/0x140
? rb_insert_color+0x340/0x360
? prelim_ref_insert+0x12d/0x430
find_parent_nodes+0x5c3/0x1830
? stack_trace_save+0x87/0xb0
? resolve_indirect_refs+0xfc0/0xfc0
? fs_reclaim_acquire+0x67/0xf0
? __kasan_check_read+0x11/0x20
? lockdep_hardirqs_on_prepare+0x210/0x210
? fs_reclaim_acquire+0x67/0xf0
? __kasan_check_read+0x11/0x20
? ___might_sleep+0x10f/0x1e0
? __kasan_kmalloc+0x9d/0xd0
? trace_hardirqs_on+0x55/0x120
btrfs_find_all_roots_safe+0x142/0x1e0
? find_parent_nodes+0x1830/0x1830
? trace_hardirqs_on+0x55/0x120
? ulist_free+0x1f/0x30
? btrfs_inode_flags_to_xflags+0x50/0x50
iterate_extent_inodes+0x20e/0x580
? tree_backref_for_extent+0x230/0x230
? release_extent_buffer+0x225/0x280
? read_extent_buffer+0xdd/0x110
? lock_downgrade+0x400/0x400
? __kasan_check_read+0x11/0x20
? lock_acquired+0xbb/0x620
? __kasan_check_write+0x14/0x20
? do_raw_spin_unlock+0xa8/0x140
? _raw_spin_unlock+0x22/0x30
? release_extent_buffer+0x225/0x280
iterate_inodes_from_logical+0x129/0x170
? iterate_inodes_from_logical+0x129/0x170
? btrfs_inode_flags_to_xflags+0x50/0x50
? iterate_extent_inodes+0x580/0x580
? __vmalloc_node+0x92/0xb0
? init_data_container+0x34/0xb0
? init_data_container+0x34/0xb0
? kvmalloc_node+0x60/0x80
btrfs_ioctl_logical_to_ino+0x158/0x230
btrfs_ioctl+0x2038/0x4360
? __kasan_check_write+0x14/0x20
? mmput+0x3b/0x220
? btrfs_ioctl_get_supported_features+0x30/0x30
? __kasan_check_read+0x11/0x20
? __kasan_check_read+0x11/0x20
? lock_release+0xc8/0x650
? __might_fault+0x64/0xd0
? __kasan_check_read+0x11/0x20
? lock_downgrade+0x400/0x400
? lockdep_hardirqs_on_prepare+0x210/0x210
? lockdep_hardirqs_on_prepare+0x13/0x210
? _raw_spin_unlock_irqrestore+0x51/0x63
? __kasan_check_read+0x11/0x20
? do_vfs_ioctl+0xfc/0x9d0
? ioctl_file_clone+0xe0/0xe0
? lock_downgrade+0x400/0x400
? lockdep_hardirqs_on_prepare+0x210/0x210
? __kasan_check_read+0x11/0x20
? lock_release+0xc8/0x650
? __task_pid_nr_ns+0xd3/0x250
? __kasan_check_read+0x11/0x20
? __fget_files+0x160/0x230
? __fget_light+0xf2/0x110
__x64_sys_ioctl+0xc3/0x100
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f29ae85b427
Code: 00 00 90 48 8b (...)
RSP: 002b:00007f29acf5fcf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007f29acf5ff40 RCX: 00007f29ae85b427
RDX: 00007f29acf5ff48 RSI: 00000000c038943b RDI: 0000000000000003
RBP: 0000000001000000 R08: 0000000000000000 R09: 00007f29acf60120
R10: 00005640d5fc7b00 R11: 0000000000000246 R12: 0000000000000003
R13: 00007f29acf5ff48 R14: 00007f29acf5ff40 R15: 00007f29acf5fef8
Modules linked in:
---[ end trace 85e5fce078dfbe04 ]---
(gdb) l *(tree_mod_log_rewind+0x3b1)
0xffffffff819e5b21 is in tree_mod_log_rewind (fs/btrfs/tree-mod-log.c:675).
670 * the modification. As we're going backwards, we do the
671 * opposite of each operation here.
672 */
673 switch (tm->op) {
674 case BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING:
675 BUG_ON(tm->slot < n);
676 fallthrough;
677 case BTRFS_MOD_LOG_KEY_REMOVE_WHILE_MOVING:
678 case BTRFS_MOD_LOG_KEY_REMOVE:
679 btrfs_set_node_key(eb, &tm->key, tm->slot);
(gdb) quit
The following steps explain in more detail how it happens:
1) We have one tree mod log user (through fiemap or the logical ino ioctl),
with a sequence number of 1, so we have fs_info->tree_mod_seq == 1.
This is task A;
2) Another task is at ctree.c:balance_level() and we have eb X currently as
the root of the tree, and we promote its single child, eb Y, as the new
root.
Then, at ctree.c:balance_level(), we call:
ret = btrfs_tree_mod_log_insert_root(root->node, child, true);
3) At btrfs_tree_mod_log_insert_root() we create a tree mod log operation
of type BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING, with a ->logical field
pointing to ebX->start. We only have one item in eb X, so we create
only one tree mod log operation, and store in the "tm_list" array;
4) Then, still at btrfs_tree_mod_log_insert_root(), we create a tree mod
log element of operation type BTRFS_MOD_LOG_ROOT_REPLACE, ->logical set
to ebY->start, ->old_root.logical set to ebX->start, ->old_root.level
set to the level of eb X and ->generation set to the generation of eb X;
5) Then btrfs_tree_mod_log_insert_root() calls tree_mod_log_free_eb() with
"tm_list" as argument. After that, tree_mod_log_free_eb() calls
tree_mod_log_insert(). This inserts the mod log operation of type
BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING from step 3 into the rbtree
with a sequence number of 2 (and fs_info->tree_mod_seq set to 2);
6) Then, after inserting the "tm_list" single element into the tree mod
log rbtree, the BTRFS_MOD_LOG_ROOT_REPLACE element is inserted, which
gets the sequence number 3 (and fs_info->tree_mod_seq set to 3);
7) Back to ctree.c:balance_level(), we free eb X by calling
btrfs_free_tree_block() on it. Because eb X was created in the current
transaction, has no other references and writeback did not happen for
it, we add it back to the free space cache/tree;
8) Later some other task B allocates the metadata extent from eb X, since
it is marked as free space in the space cache/tree, and uses it as a
node for some other btree;
9) The tree mod log user task calls btrfs_search_old_slot(), which calls
btrfs_get_old_root(), and finally that calls tree_mod_log_oldest_root()
with time_seq == 1 and eb_root == eb Y;
10) The first iteration of the while loop finds the tree mod log element
with sequence number 3, for the logical address of eb Y and of type
BTRFS_MOD_LOG_ROOT_REPLACE;
11) Because the operation type is BTRFS_MOD_LOG_ROOT_REPLACE, we don't
break out of the loop, and set root_logical to point to
tm->old_root.logical, which corresponds to the logical address of
eb X;
12) On the next iteration of the while loop, the call to
tree_mod_log_search_oldest() returns the smallest tree mod log element
for the logical address of eb X, which has a sequence number of 2, an
operation type of BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING and
corresponds to the old slot 0 of eb X (eb X had only 1 item in it
before being freed at step 7);
13) We then break out of the while loop and return the tree mod log
operation of type BTRFS_MOD_LOG_ROOT_REPLACE (eb Y), and not the one
for slot 0 of eb X, to btrfs_get_old_root();
14) At btrfs_get_old_root(), we process the BTRFS_MOD_LOG_ROOT_REPLACE
operation and set "logical" to the logical address of eb X, which was
the old root. We then call tree_mod_log_search() passing it the logical
address of eb X and time_seq == 1;
15) But before calling tree_mod_log_search(), task B locks eb X, adds a
key to eb X, which results in adding a tree mod log operation of type
BTRFS_MOD_LOG_KEY_ADD, with a sequence number of 4, to the tree mod
log, and increments the number of items in eb X from 0 to 1.
Now fs_info->tree_mod_seq has a value of 4;
16) Task A then calls tree_mod_log_search(), which returns the most recent
tree mod log operation for eb X, which is the one just added by task B
at the previous step, with a sequence number of 4, a type of
BTRFS_MOD_LOG_KEY_ADD and for slot 0;
17) Before task A locks and clones eb X, task A adds another key to eb X,
which results in adding a new BTRFS_MOD_LOG_KEY_ADD mod log operation,
with a sequence number of 5, for slot 1 of eb X, increments the
number of items in eb X from 1 to 2, and unlocks eb X.
Now fs_info->tree_mod_seq has a value of 5;
18) Task A then locks eb X and clones it. The clone has a value of 2 for
the number of items and the pointer "tm" points to the tree mod log
operation with sequence number 4, not the most recent one with a
sequence number of 5, so there is mismatch between the number of
mod log operations that are going to be applied to the cloned version
of eb X and the number of items in the clone;
19) Task A then calls tree_mod_log_rewind() with the clone of eb X, the
tree mod log operation with sequence number 4 and a type of
BTRFS_MOD_LOG_KEY_ADD, and time_seq == 1;
20) At tree_mod_log_rewind(), we set the local variable "n" with a value
of 2, which is the number of items in the clone of eb X.
Then in the first iteration of the while loop, we process the mod log
operation with sequence number 4, which is targeted at slot 0 and has
a type of BTRFS_MOD_LOG_KEY_ADD. This results in decrementing "n" from
2 to 1.
Then we pick the next tree mod log operation for eb X, which is the
tree mod log operation with a sequence number of 2, a type of
BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING and for slot 0, it is the one
added in step 5 to the tree mod log tree.
We go back to the top of the loop to process this mod log operation,
and because its slot is 0 and "n" has a value of 1, we hit the BUG_ON:
(...)
switch (tm->op) {
case BTRFS_MOD_LOG_KEY_REMOVE_WHILE_FREEING:
BUG_ON(tm->slot < n);
fallthrough;
(...)
Fix this by checking for a more recent tree mod log operation after locking
and cloning the extent buffer of the old root node, and use it as the first
operation to apply to the cloned extent buffer when rewinding it.
Stable backport notes: due to moved code and renames, in =< 5.11 the
change should be applied to ctree.c:get_old_root.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Link: https://lore.kernel.org/linux-btrfs/20210404040732.GZ32440@hungrycats.org/
Fixes: 834328a849 ("Btrfs: tree mod log's old roots could still be part of the tree")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4fb44dd2c1 upstream.
In snd_sb_qsound_build, snd_ctl_add(..,p->qsound_switch...) and
snd_ctl_add(..,p->qsound_space..) are called. But the second
arguments of snd_ctl_add() could be freed via snd_ctl_add_replace()
->snd_ctl_free_one(). After the error code is returned,
snd_sb_qsound_destroy(p) is called in __error branch.
But in snd_sb_qsound_destroy(), the freed p->qsound_switch and
p->qsound_space are still used by snd_ctl_remove().
My patch set p->qsound_switch and p->qsound_space to NULL if
snd_ctl_add() failed to avoid the uaf bugs. But these codes need
to further be improved with the code style.
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426145541.8070-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c98f57440 upstream.
Our code analyzer reported a uaf.
In snd_emu8000_create_mixer, the callee snd_ctl_add(..,emu->controls[i])
calls snd_ctl_add_replace(.., kcontrol,..). Inside snd_ctl_add_replace(),
if error happens, kcontrol will be freed by snd_ctl_free_one(kcontrol).
Then emu->controls[i] points to a freed memory, and the execution comes
to __error branch of snd_emu8000_create_mixer. The freed emu->controls[i]
is used in snd_ctl_remove(card, emu->controls[i]).
My patch set emu->controls[i] to NULL if snd_ctl_add() failed to avoid
the uaf.
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426131129.4796-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90d6697810 ]
Since the 'mfs' member has been declared as 'u32' in include/scsi/libfc.h,
use the %u format specifier instead of %hu. This patch fixes the following
clang compiler warning:
warning: format specifies type
'unsigned short' but the argument has type 'u32' (aka 'unsigned int')
[-Wformat]
"lport->mfs:%hu\n", mfs, lport->mfs);
~~~ ^~~~~~~~~~
%u
Link: https://lore.kernel.org/r/20210415220826.29438-8-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fffd18ec65 ]
Fix a crash caused by a double put on the node when the driver completed an
ACC for an unsolicted abort on the same node. The second put was executed
by lpfc_nlp_not_used() and is wrong because the completion routine executes
the nlp_put when the iocbq was released. Additionally, the driver is
issuing a LOGO then immediately calls lpfc_nlp_set_state to put the node
into NPR. This call does nothing.
Remove the lpfc_nlp_not_used call and additional set_state in the
completion routine. Remove the lpfc_nlp_set_state post issue_logo. Isn't
necessary.
Link: https://lore.kernel.org/r/20210412013127.2387-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ad52bdb22 ]
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4e6644cd ]
For two of the supported sensors the stv06xx driver allocates memory which
is stored in sd->sensor_priv. This memory is freed on a disconnect, but if
the probe() fails, then it isn't freed and so this leaks memory.
Add a new probe_error() op that drivers can use to free any allocated
memory in case there was a probe failure.
Thanks to Pavel Skripkin <paskripkin@gmail.com> for discovering the cause
of the memory leak.
Reported-and-tested-by: syzbot+e7f4c64a4248a0340c37@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7cd0da982 ]
syzbot reported memory leak in dvb-usb. The problem was
in invalid error handling in dvb_usb_adapter_init().
for (n = 0; n < d->props.num_adapters; n++) {
....
if ((ret = dvb_usb_adapter_stream_init(adap)) ||
(ret = dvb_usb_adapter_dvb_init(adap, adapter_nrs)) ||
(ret = dvb_usb_adapter_frontend_init(adap))) {
return ret;
}
...
d->num_adapters_initialized++;
...
}
In case of error in dvb_usb_adapter_dvb_init() or
dvb_usb_adapter_dvb_init() d->num_adapters_initialized won't be
incremented, but dvb_usb_adapter_exit() relies on it:
for (n = 0; n < d->num_adapters_initialized; n++)
So, allocated objects won't be freed.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reported-by: syzbot+3c2be7424cea3b932b0e@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a15275b6a ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9541720c ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa56f5f1fe ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ae256945 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6cfa007b3 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 443ec4bbc6 ]
The EDID had a few mistakes as reported by edid-decode:
Block 1, CTA-861 Extension Block:
Video Data Block: For improved preferred timing interoperability, set 'Native detailed modes' to 1.
Video Capability Data Block: S_PT is equal to S_IT and S_CE, so should be set to 0 instead.
Fixed those.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ae10a7dc8 ]
If some error occurs, URB buffers should also be freed. If they aren't
freed with the dvb here, the em28xx_dvb_fini call doesn't frees the URB
buffers as dvb is set to NULL. The function in which error occurs should
do all the cleanup for the allocations it had done.
Tested the patch with the reproducer provided by syzbot. This patch
fixes the memleak.
Reported-by: syzbot+889397c820fa56adf25d@syzkaller.appspotmail.com
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8941550aa ]
This recent change introduce SDMA interrupt info printing with irq->process function.
These functions do not require a set function to enable/disable the irq
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c759b2970c ]
Add a fix for the memory leak bugs that can occur when the
saa7164_encoder_register() function fails.
The function allocates memory without explicitly freeing
it when errors occur.
Add a better error handling that deallocate the unused buffers before the
function exits during a fail.
Signed-off-by: Daniel Niv <danielniv3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c309a3e879 ]
When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done
Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4d57c22ac ]
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a9213a935 ]
A few BUG_ON()'s in replace_path are purely to keep us from making
logical mistakes, so replace them with ASSERT()'s.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1723d8b87 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092716.3270248-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c650b8dc7a ]
When Secure World returns, it may have changed the size attribute of the
memory references passed as [in/out] parameters. The GlobalPlatform TEE
Internal Core API specification does not restrict the values that this
size can take. In particular, Secure World may increase the value to be
larger than the size of the input buffer to indicate that it needs more.
Therefore, the size check in optee_from_msg_param() is incorrect and
needs to be removed. This fixes a number of failed test cases in the
GlobalPlatform TEE Initial Configuratiom Test Suite v2_0_0_0-2017_06_09
when OP-TEE is compiled without dynamic shared memory support
(CFG_CORE_DYN_SHM=n).
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Suggested-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Jerome Forissier <jerome@forissier.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8abe7fc26a ]
When cross-compiling with Clang, the `$(CLANG_FLAGS)' variable
contains additional flags needed to build C and assembly sources
for the target platform. Normally this variable is automatically
included in `$(KBUILD_CFLAGS)' via the top-level Makefile.
The x86 real-mode makefile builds `$(REALMODE_CFLAGS)' from a
plain assignment and therefore drops the Clang flags. This causes
Clang to not recognize x86-specific assembler directives:
arch/x86/realmode/rm/header.S:36:1: error: unknown directive
.type real_mode_header STT_OBJECT ; .size real_mode_header, .-real_mode_header
^
Explicit propagation of `$(CLANG_FLAGS)' to `$(REALMODE_CFLAGS)',
which is inherited by real-mode make rules, fixes cross-compilation
with Clang for x86 targets.
Relevant flags:
* `--target' sets the target architecture when cross-compiling. This
flag must be set for both compilation and assembly (`KBUILD_AFLAGS')
to support architecture-specific assembler directives.
* `-no-integrated-as' tells clang to assemble with GNU Assembler
instead of its built-in LLVM assembler. This flag is set by default
unless `LLVM_IAS=1' is set, because the LLVM assembler can't yet
parse certain GNU extensions.
Signed-off-by: John Millikin <john@john-millikin.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Link: https://lkml.kernel.org/r/20210326000435.4785-2-nathan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4514d991d9 ]
It should not be necessary to update the current_state field of
struct pci_dev in pci_enable_device_flags() before calling
do_pci_enable_device() for the device, because none of the
code between that point and the pci_set_power_state() call in
do_pci_enable_device() invoked later depends on it.
Moreover, doing that is actively harmful in some cases. For example,
if the given PCI device depends on an ACPI power resource whose _STA
method initially returns 0 ("off"), but the config space of the PCI
device is accessible and the power state retrieved from the
PCI_PM_CTRL register is D0, the current_state field in the struct
pci_dev representing that device will get out of sync with the
power.state of its ACPI companion object and that will lead to
power management issues going forward.
To avoid such issues it is better to leave the current_state value
as is until it is changed to PCI_D0 by do_pci_enable_device() as
appropriate. However, the power state of the device is not changed
to PCI_D0 if it is already enabled when pci_enable_device_flags()
gets called for it, so update its current_state in that case, but
use pci_update_current_state() covering platform PM too for that.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64364bc912 ]
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ed330e95a19dc367819c5b4d78bf7a541c35aa0a.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71ca43f30d ]
The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event. If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions. To avoid this, set the
connected flag to false until the stop active transfers is complete.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1616146285-19149-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a59c68a6a3 ]
Currently user can configure UAC1 function with
parameters that violate UAC1 spec or are not supported
by UAC1 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC1 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-5-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 67addf2900 upstream.
When creating a subvolume we allocate an extent buffer for its root node
after starting a transaction. We setup a root item for the subvolume that
points to that extent buffer and then attempt to insert the root item into
the root tree - however if that fails, due to ENOMEM for example, we do
not free the extent buffer previously allocated and we do not abort the
transaction (as at that point we did nothing that can not be undone).
This means that we effectively do not return the metadata extent back to
the free space cache/tree and we leave a delayed reference for it which
causes a metadata extent item to be added to the extent tree, in the next
transaction commit, without having backreferences. When this happens
'btrfs check' reports the following:
$ btrfs check /dev/sdi
Opening filesystem to check...
Checking filesystem on /dev/sdi
UUID: dce2cb9d-025f-4b05-a4bf-cee0ad3785eb
[1/7] checking root items
[2/7] checking extents
ref mismatch on [30425088 16384] extent item 1, found 0
backref 30425088 root 256 not referenced back 0x564a91c23d70
incorrect global backref count on 30425088 found 1 wanted 0
backpointer mismatch on [30425088 16384]
owner ref check failed [30425088 16384]
ERROR: errors found in extent allocation tree or chunk allocation
[3/7] checking free space cache
[4/7] checking fs roots
[5/7] checking only csums items (without verifying data)
[6/7] checking root refs
[7/7] checking quota groups skipped (not enabled on this FS)
found 212992 bytes used, error(s) found
total csum bytes: 0
total tree bytes: 131072
total fs tree bytes: 32768
total extent tree bytes: 16384
btree space waste bytes: 124669
file data blocks allocated: 65536
referenced 65536
So fix this by freeing the metadata extent if btrfs_insert_root() returns
an error.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 147186f531 upstream.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9046625511 upstream.
When mounting eCryptfs, a null "dev_name" argument to ecryptfs_mount()
causes a kernel panic if the parsed options are valid. The easiest way to
reproduce this is to call mount() from userspace with an existing
eCryptfs mount's options and a "source" argument of 0.
Error out if "dev_name" is null in ecryptfs_mount()
Fixes: 237fead619 ("[PATCH] ecryptfs: fs/Makefile and fs/Kconfig")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffrey Mitchell <jeffrey.mitchell@starlab.io>
Signed-off-by: Tyler Hicks <code@tyhicks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cfd895643 upstream.
In cm_write(), if the 'buf' is allocated memory but not fully consumed,
it is possible to reallocate the buffer without freeing it by passing
'*ppos' as 0 on a subsequent call.
Add an explicit kfree() before kzalloc() to prevent the possible memory
leak.
Fixes: 526b4af47f ("ACPI: Split out custom_method functionality into an own driver")
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e483bb9a99 upstream.
In cm_write(), buf is always freed when reaching the end of the
function. If the requested count is less than table.length, the
allocated buffer will be freed but subsequent calls to cm_write() will
still try to access it.
Remove the unconditional kfree(buf) at the end of the function and
set the buf to NULL in the -EINVAL error path to match the rest of
function.
Fixes: 03d1571d95 ("ACPI: custom_method: fix memory leaks")
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6759e18e5c upstream.
On recent Thinkpad platforms it was reported that temp sensor 11 was
always incorrectly displaying 66C. It turns out the reason for this is
that this location in EC RAM is not a temperature sensor but is the
power supply ID (offset 0xC2).
Based on feedback from the Lenovo firmware team the EC RAM version can
be determined and for the current version (3) only the 0x78 to 0x7F
range is used for temp sensors. I don't have any details for earlier
versions so I have left the implementation unaltered there.
Note - in this block only 0x78 and 0x79 are officially designated (CPU &
GPU sensors). The use of the other locations in the block will vary from
platform to platform; but the existing logic to detect a sensor presence
holds.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20210407212015.298222-1-markpearson@lenovo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca91fd8c76 upstream.
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9b34ddbe2 upstream.
The negation logic for the case where the off_reg is sitting in the
dst register is not correct given then we cannot just invert the add
to a sub or vice versa. As a fix, perform the final bitwise and-op
unconditionally into AX from the off_reg, then move the pointer from
the src to dst and finally use AX as the source for the original
pointer arithmetic operation such that the inversion yields a correct
result. The single non-AX mov in between is possible given constant
blinding is retaining it as it's not an immediate based operation.
Fixes: 979d63d50c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7ba0165d upstream
>From [1]
"GCC 10 (PR 91233) won't silently allow registers that are not
architecturally available to be present in the clobber list anymore,
resulting in build failure for mips*r6 targets in form of:
...
.../sysdep.h:146:2: error: the register ‘lo’ cannot be clobbered in ‘asm’ for the current target
146 | __asm__ volatile ( \
| ^~~~~~~
This is because base R6 ISA doesn't define hi and lo registers w/o DSP
extension. This patch provides the alternative clobber list for r6 targets
that won't include those registers."
Since kernel 5.4 and mips support for generic vDSO [2], the kernel fail to
build for mips r6 cpus with gcc 10 for the same reason as glibc.
[1] https://sourceware.org/git/?p=glibc.git;a=commit;h=020b2a97bb15f807c0482f0faee2184ed05bcad8
[2] '24640f233b46 ("mips: Add support for generic vDSO")'
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1690905240 upstream
There are multiple instances in the kernel where we need to include or
exclude particular instructions based on the ISA revision of the target
processor. For MIPS32 / MIPS64, the compiler exports a __mips_isa_rev
define. However, when targeting MIPS I - V, this define is absent. This
leads to each use of __mips_isa_rev having to check that it is defined
first. To simplify this, introduce the isa-rev.h header which always
exports MIPS_ISA_REV. The name is changed so as to avoid confusion with
the compiler builtin and to avoid accidentally using the builtin.
MIPS_ISA_REV is defined to the compilers builtin if provided, or 0,
which satisfies all current usages.
Suggested-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18676/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the backport of the changes to fix CVE 2019-7308, the
selftests also need to be fixed up, as was done originally
in mainline 80c9b2fae8 ("bpf: add various test cases to selftests").
4.14 commit 03f11a51a1 ("bpf: Fix selftests are changes for CVE 2019-7308")
did that, but since there was an error in the backport, some
selftests did not change output. So, add them now that this error
has been fixed, and their output has actually changed as expected.
This adds the rest of the changed test outputs from 80c9b2fae8.
Fixes: 03f11a51a1 ("bpf: Fix selftests are changes for CVE 2019-7308")
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 4.14 backport of 9d7eceede ("bpf: restrict unknown scalars of mixed
signed bounds for unprivileged") adds the PTR_TO_MAP_VALUE check to the
wrong location in adjust_ptr_min_max_vals(), most likely because 4.14
doesn't include the commit that updates the if-statement to a
switch-statement (aad2eeaf4 "bpf: Simplify ptr_min_max_vals adjustment").
Move the check to the proper location in adjust_ptr_min_max_vals().
Fixes: 17efa65350 ("bpf: restrict unknown scalars of mixed signed bounds for unprivileged")
Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com>
Reviewed-by: Frank van der Linden <fllinden@amazon.com>
Reviewed-by: Ethan Chen <yishache@amazon.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6998a8800d upstream.
Commit 1a1c130ab7 ("ACPI: tables: x86: Reserve memory occupied by
ACPI tables") attempted to address an issue with reserving the memory
occupied by ACPI tables, but it broke the initrd-based table override
mechanism relied on by multiple users.
To restore the initrd-based ACPI table override functionality, move
the acpi_boot_table_init() invocation in setup_arch() on x86 after
the acpi_table_upgrade() one.
Fixes: 1a1c130ab7 ("ACPI: tables: x86: Reserve memory occupied by ACPI tables")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a1c130ab7 upstream.
The following problem has been reported by George Kennedy:
Since commit 7fef431be9 ("mm/page_alloc: place pages to tail
in __free_pages_core()") the following use after free occurs
intermittently when ACPI tables are accessed.
BUG: KASAN: use-after-free in ibft_init+0x134/0xc49
Read of size 4 at addr ffff8880be453004 by task swapper/0/1
CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc1-7a7fd0d #1
Call Trace:
dump_stack+0xf6/0x158
print_address_description.constprop.9+0x41/0x60
kasan_report.cold.14+0x7b/0xd4
__asan_report_load_n_noabort+0xf/0x20
ibft_init+0x134/0xc49
do_one_initcall+0xc4/0x3e0
kernel_init_freeable+0x5af/0x66b
kernel_init+0x16/0x1d0
ret_from_fork+0x22/0x30
ACPI tables mapped via kmap() do not have their mapped pages
reserved and the pages can be "stolen" by the buddy allocator.
Apparently, on the affected system, the ACPI table in question is
not located in "reserved" memory, like ACPI NVS or ACPI Data, that
will not be used by the buddy allocator, so the memory occupied by
that table has to be explicitly reserved to prevent the buddy
allocator from using it.
In order to address this problem, rearrange the initialization of the
ACPI tables on x86 to locate the initial tables earlier and reserve
the memory occupied by them.
The other architectures using ACPI should not be affected by this
change.
Link: https://lore.kernel.org/linux-acpi/1614802160-29362-1-git-send-email-george.kennedy@oracle.com/
Reported-by: George Kennedy <george.kennedy@oracle.com>
Tested-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8b3b51961 upstream.
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927 ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ad5692db7 upstream.
Commit 8a12f88361 ("net: hso: fix null-ptr-deref during tty device
unregistration") fixed the racy minor allocation reported by syzbot, but
introduced an unconditional NULL-pointer dereference on every disconnect
instead.
Specifically, the serial device table must no longer be accessed after
the minor has been released by hso_serial_tty_unregister().
Fixes: 8a12f88361 ("net: hso: fix null-ptr-deref during tty device unregistration")
Cc: stable@vger.kernel.org
Cc: Anirudh Rayabharam <mail@anirudhrb.com>
Reported-by: Leonardo Antoniazzi <leoanto@aruba.it>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5849cdf8c1 upstream.
Commit in Fixes: added support for kexec-ing a kernel on panic using a
new system call. As part of it, it does prepare a memory map for the new
kernel.
However, while doing so, it wrongly accesses memory it has not
allocated: it accesses the first element of the cmem->ranges[] array in
memmap_exclude_ranges() but it has not allocated the memory for it in
crash_setup_memmap_entries(). As KASAN reports:
BUG: KASAN: vmalloc-out-of-bounds in crash_setup_memmap_entries+0x17e/0x3a0
Write of size 8 at addr ffffc90000426008 by task kexec/1187
(gdb) list *crash_setup_memmap_entries+0x17e
0xffffffff8107cafe is in crash_setup_memmap_entries (arch/x86/kernel/crash.c:322).
317 unsigned long long mend)
318 {
319 unsigned long start, end;
320
321 cmem->ranges[0].start = mstart;
322 cmem->ranges[0].end = mend;
323 cmem->nr_ranges = 1;
324
325 /* Exclude elf header region */
326 start = image->arch.elf_load_addr;
(gdb)
Make sure the ranges array becomes a single element allocated.
[ bp: Write a proper commit message. ]
Fixes: dd5f726076 ("kexec: support for kexec on panic using new system call")
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Young <dyoung@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/725fa3dc1da2737f0f6188a1a9701bead257ea9d.camel@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4bf09dc3a ]
The ia64_mf() macro defined in tools/arch/ia64/include/asm/barrier.h is
already defined in <asm/gcc_intrin.h> on ia64 which causes libbpf
failing to build:
CC /usr/src/linux/tools/bpf/bpftool//libbpf/staticobjs/libbpf.o
In file included from /usr/src/linux/tools/include/asm/barrier.h:24,
from /usr/src/linux/tools/include/linux/ring_buffer.h:4,
from libbpf.c:37:
/usr/src/linux/tools/include/asm/../../arch/ia64/include/asm/barrier.h:43: error: "ia64_mf" redefined [-Werror]
43 | #define ia64_mf() asm volatile ("mf" ::: "memory")
|
In file included from /usr/include/ia64-linux-gnu/asm/intrinsics.h:20,
from /usr/include/ia64-linux-gnu/asm/swab.h:11,
from /usr/include/linux/swab.h:8,
from /usr/include/linux/byteorder/little_endian.h:13,
from /usr/include/ia64-linux-gnu/asm/byteorder.h:5,
from /usr/src/linux/tools/include/uapi/linux/perf_event.h:20,
from libbpf.c:36:
/usr/include/ia64-linux-gnu/asm/gcc_intrin.h:382: note: this is the location of the previous definition
382 | #define ia64_mf() __asm__ volatile ("mf" ::: "memory")
|
cc1: all warnings being treated as errors
Thus, remove the definition from tools/arch/ia64/include/asm/barrier.h.
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2af9da4f8 ]
Fix IA64 discontig.c Section mismatch warnings.
When CONFIG_SPARSEMEM=y and CONFIG_MEMORY_HOTPLUG=y, the functions
computer_pernodesize() and scatter_node_data() should not be marked as
__meminit because they are needed after init, on any memory hotplug
event. Also, early_nr_cpus_node() is called by compute_pernodesize(),
so early_nr_cpus_node() cannot be __meminit either.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1612): Section mismatch in reference from the function arch_alloc_nodedata() to the function .meminit.text:compute_pernodesize()
The function arch_alloc_nodedata() references the function __meminit compute_pernodesize().
This is often because arch_alloc_nodedata lacks a __meminit annotation or the annotation of compute_pernodesize is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1692): Section mismatch in reference from the function arch_refresh_nodedata() to the function .meminit.text:scatter_node_data()
The function arch_refresh_nodedata() references the function __meminit scatter_node_data().
This is often because arch_refresh_nodedata lacks a __meminit annotation or the annotation of scatter_node_data is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1502): Section mismatch in reference from the function compute_pernodesize() to the function .meminit.text:early_nr_cpus_node()
The function compute_pernodesize() references the function __meminit early_nr_cpus_node().
This is often because compute_pernodesize lacks a __meminit annotation or the annotation of early_nr_cpus_node is wrong.
Link: https://lkml.kernel.org/r/20210411001201.3069-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mike Rapoport <rppt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416dcc5ce9 ]
Fix the following coccicheck warning:
./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28:
duplicated argument to & or |
The CN6XXX_INTR_M1UPB0_ERR here is duplicate.
Here should be CN6XXX_INTR_M1UNB0_ERR.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2afeec08ab ]
The logic in connect() is currently written with the assumption that
xenbus_watch_pathfmt() will return an error for a node that does not
exist. This assumption is incorrect: xenstore does allow a watch to
be registered for a nonexistent node (and will send notifications
should the node be subsequently created).
As of commit 1f2565780 ("xen-netback: remove 'hotplug-status' once it
has served its purpose"), this leads to a failure when a domU
transitions into XenbusStateConnected more than once. On the first
domU transition into Connected state, the "hotplug-status" node will
be deleted by the hotplug_status_changed() callback in dom0. On the
second or subsequent domU transition into Connected state, the
hotplug_status_changed() callback will therefore never be invoked, and
so the backend will remain stuck in InitWait.
This failure prevents scenarios such as reloading the xen-netfront
module within a domU, or booting a domU via iPXE. There is
unfortunately no way for the domU to work around this dom0 bug.
Fix by explicitly checking for existence of the "hotplug-status" node,
thereby creating the behaviour that was previously assumed to exist.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a994eddb94 ]
Currently psw_idle does not allocate a stack frame and does not
save its r14 and r15 into the save area. Even though this is valid from
call ABI point of view, because psw_idle does not make any calls
explicitly, in reality psw_idle is an entry point for controlled
transition into serving interrupts. So, in practice, psw_idle stack
frame is analyzed during stack unwinding. Depending on build options
that r14 slot in the save area of psw_idle might either contain a value
saved by previous sibling call or complete garbage.
[task 0000038000003c28] do_ext_irq+0xd6/0x160
[task 0000038000003c78] ext_int_handler+0xba/0xe8
[task *0000038000003dd8] psw_idle_exit+0x0/0x8 <-- pt_regs
([task 0000038000003dd8] 0x0)
[task 0000038000003e10] default_idle_call+0x42/0x148
[task 0000038000003e30] do_idle+0xce/0x160
[task 0000038000003e70] cpu_startup_entry+0x36/0x40
[task 0000038000003ea0] arch_call_rest_init+0x76/0x80
So, to make a stacktrace nicer and actually point for the real caller of
psw_idle in this frequently occurring case, make psw_idle save its r14.
[task 0000038000003c28] do_ext_irq+0xd6/0x160
[task 0000038000003c78] ext_int_handler+0xba/0xe8
[task *0000038000003dd8] psw_idle_exit+0x0/0x6 <-- pt_regs
([task 0000038000003dd8] arch_cpu_idle+0x3c/0xd0)
[task 0000038000003e10] default_idle_call+0x42/0x148
[task 0000038000003e30] do_idle+0xce/0x160
[task 0000038000003e70] cpu_startup_entry+0x36/0x40
[task 0000038000003ea0] arch_call_rest_init+0x76/0x80
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ebdb3741 ]
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa8ba6e5dc ]
When input_register_device() fails, no error return code is assigned.
To fix this bug, ret is assigned with -ENOENT as error return code.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196d941753 ]
When updating pin names for Intel Lewisburg, the numbers of pins were
left behind. Update them accordingly.
Fixes: e66ff71fd0 ("pinctrl: lewisburg: Update pin list according to v1.1v6")
Signed-off-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The backport of upstream patch 5dccdc5a19 ("ext4: do not iput inode
under running transaction in ext4_rename()") introduced a regression on
the stable kernels 4.14 and older. One of the end_rename error label was
forgetting to change to release_bh, which may trigger below bug.
------------[ cut here ]------------
kernel BUG at /home/zhangyi/hulk-4.4/fs/ext4/ext4_jbd2.c:30!
...
Call Trace:
[<ffffffff8b4207b2>] ext4_rename+0x9e2/0x10c0
[<ffffffff8b331324>] ? unlazy_walk+0x124/0x2a0
[<ffffffff8b420eb5>] ext4_rename2+0x25/0x60
[<ffffffff8b335104>] vfs_rename+0x3a4/0xed0
[<ffffffff8b33a7ad>] SYSC_renameat2+0x57d/0x7f0
[<ffffffff8b33c119>] SyS_renameat+0x19/0x30
[<ffffffff8bc57bb8>] entry_SYSCALL_64_fastpath+0x18/0x78
...
---[ end trace 75346ce7c76b9f06 ]---
Fixes: d962f1b4ef ("ext4: do not iput inode under running transaction in ext4_rename()")
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a12f88361 upstream
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17839856fd upstream.
Doing a "get_user_pages()" on a copy-on-write page for reading can be
ambiguous: the page can be COW'ed at any time afterwards, and the
direction of a COW event isn't defined.
Yes, whoever writes to it will generally do the COW, but if the thread
that did the get_user_pages() unmapped the page before the write (and
that could happen due to memory pressure in addition to any outright
action), the writer could also just take over the old page instead.
End result: the get_user_pages() call might result in a page pointer
that is no longer associated with the original VM, and is associated
with - and controlled by - another VM having taken it over instead.
So when doing a get_user_pages() on a COW mapping, the only really safe
thing to do would be to break the COW when getting the page, even when
only getting it for reading.
At the same time, some users simply don't even care.
For example, the perf code wants to look up the page not because it
cares about the page, but because the code simply wants to look up the
physical address of the access for informational purposes, and doesn't
really care about races when a page might be unmapped and remapped
elsewhere.
This adds logic to force a COW event by setting FOLL_WRITE on any
copy-on-write mapping when FOLL_GET (or FOLL_PIN) is used to get a page
pointer as a result.
The current semantics end up being:
- __get_user_pages_fast(): no change. If you don't ask for a write,
you won't break COW. You'd better know what you're doing.
- get_user_pages_fast(): the fast-case "look it up in the page tables
without anything getting mmap_sem" now refuses to follow a read-only
page, since it might need COW breaking. Which happens in the slow
path - the fast path doesn't know if the memory might be COW or not.
- get_user_pages() (including the slow-path fallback for gup_fast()):
for a COW mapping, turn on FOLL_WRITE for FOLL_GET/FOLL_PIN, with
very similar semantics to FOLL_FORCE.
If it turns out that we want finer granularity (ie "only break COW when
it might actually matter" - things like the zero page are special and
don't need to be broken) we might need to push these semantics deeper
into the lookup fault path. So if people care enough, it's possible
that we might end up adding a new internal FOLL_BREAK_COW flag to go
with the internal FOLL_COW flag we already have for tracking "I had a
COW".
Alternatively, if it turns out that different callers might want to
explicitly control the forced COW break behavior, we might even want to
make such a flag visible to the users of get_user_pages() instead of
using the above default semantics.
But for now, this is mostly commentary on the issue (this commit message
being a lot bigger than the patch, and that patch in turn is almost all
comments), with that minimal "enable COW breaking early" logic using the
existing FOLL_WRITE behavior.
[ It might be worth noting that we've always had this ambiguity, and it
could arguably be seen as a user-space issue.
You only get private COW mappings that could break either way in
situations where user space is doing cooperative things (ie fork()
before an execve() etc), but it _is_ surprising and very subtle, and
fork() is supposed to give you independent address spaces.
So let's treat this as a kernel issue and make the semantics of
get_user_pages() easier to understand. Note that obviously a true
shared mapping will still get a page that can change under us, so this
does _not_ mean that get_user_pages() somehow returns any "stable"
page ]
[surenb: backport notes
Replaced (gup_flags | FOLL_WRITE) with write=1 in gup_pgd_range.
Removed FOLL_PIN usage in should_force_cow_break since it's missing in
the earlier kernels.]
Reported-by: Jann Horn <jannh@google.com>
Tested-by: Christoph Hellwig <hch@lst.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kirill Shutemov <kirill@shutemov.name>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[surenb: backport to 4.14 kernel]
Cc: stable@vger.kernel.org # 4.14.x
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2f7eca60b upstream.
Since uprobes is not supported for thumb, check that the thumb bit is
not set when matching the uprobes instruction hooks.
The Arm UDF instructions used for uprobes triggering
(UPROBE_SWBP_ARM_INSN and UPROBE_SS_ARM_INSN) coincidentally share the
same encoding as a pair of unallocated 32-bit thumb instructions (not
UDF) when the condition code is 0b1111 (0xf). This in effect makes it
possible to trigger the uprobes functionality from thumb, and at that
using two unallocated instructions which are not permanently undefined.
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Cc: stable@vger.kernel.org
Fixes: c7edc9e326 ("ARM: add uprobes support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30e3b4f256 ]
Since commit 30fdfb929e ("PCI: Add a call to pci_assign_irq() in
pci_device_probe()"), the PCI code will call the IRQ mapping function
whenever a PCI driver is probed. If these are marked as __init, this
causes an oops if a PCI driver is loaded or bound after the kernel has
initialised.
Fixes: 30fdfb929e ("PCI: Add a call to pci_assign_irq() in pci_device_probe()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c451f3ef6 upstream.
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since
interrupt_rx() calls napi_schedule_prep/__napi_schedule during every
receive interrupt.
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a6abccbd upstream.
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(),
which will calls napi_schedule if previous state is VNIC_CLOSED
(i.e, the reset case, and "ifconfig down" case). So there is no need
for do_reset to call napi_schedule again at the end of the function
though napi_schedule will neglect the request if napi is already
scheduled.
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0775ebc4cf upstream.
__ibmvnic_open calls napi_disable without checking whether NAPI polling
has already been disabled or not. This could cause napi_disable
being called twice, which could generate deadlock. For example,
the first napi_disable will spin until NAPI_STATE_SCHED is cleared
by napi_complete_done, then set it again.
When napi_disable is called the second time, it will loop infinitely
because no dev->poll will be running to clear NAPI_STATE_SCHED.
To prevent above scenario from happening, call ibmvnic_napi_disable()
which checks if napi is disabled or not before calling napi_disable.
Fixes: bfc32f2973 ("ibmvnic: Move resource initialization to its own routine")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e39a072a6 upstream.
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e]
Call Trace:
[2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e]
[2160294.717666] dev_xdp_install+0x4f/0x70
[2160294.718036] dev_change_xdp_fd+0x11f/0x230
[2160294.718380] ? dev_disable_lro+0xe0/0xe0
[2160294.718705] do_setlink+0xac7/0xe70
[2160294.719035] ? __nla_parse+0xed/0x120
[2160294.719365] rtnl_newlink+0x73b/0x860
Fixes: 41c445ff0f ("i40e: main driver core")
Co-developed-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Jason Xing <xingwanli@kuaishou.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 610f8c0fc8 upstream.
A sit interface created without a local or a remote address is linked
into the `sit_net::tunnels_wc` list of its original namespace. When
deleting a network namespace, delete the devices that have been moved.
The following script triggers a null pointer dereference if devices
linked in a deleted `sit_net` remain:
for i in `seq 1 30`; do
ip netns add ns-test
ip netns exec ns-test ip link add dev veth0 type veth peer veth1
ip netns exec ns-test ip link add dev sit$i type sit dev veth0
ip netns exec ns-test ip link set dev sit$i netns $$
ip netns del ns-test
done
for i in `seq 1 30`; do
ip link del dev sit$i
done
Fixes: 5e6700b3bf ("sit: add support of x-netns")
Signed-off-by: Hristo Venev <hristo@venev.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31457db375 upstream.
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 176ddd8917 upstream.
When the cache_type for the SCSI device is changed, the SCSI layer issues a
MODE_SELECT command. The caching mode details are communicated via a
request buffer associated with the SCSI command with data direction set as
DMA_TO_DEVICE (scsi_mode_select()). When this command reaches the libata
layer, as a part of generic initial setup, libata layer sets up the
scatterlist for the command using the SCSI command (ata_scsi_qc_new()).
This command is then translated by the libata layer into
ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat()). The libata layer treats
this as a non-data command (ata_mselect_caching()), since it only needs an
ATA taskfile to pass the caching on/off information to the device. It does
not need the scatterlist that has been setup, so it does not perform
dma_map_sg() on the scatterlist (ata_qc_issue()). Unfortunately, when this
command reaches the libsas layer (sas_ata_qc_issue()), libsas layer sees it
as a non-data command with a scatterlist. It cannot extract the correct DMA
length since the scatterlist has not been mapped with dma_map_sg() for a
DMA operation. When this partially constructed SAS task reaches pm80xx
LLDD, it results in the following warning:
"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"
Update libsas to handle ATA non-data commands separately so num_scatter and
total_xfer_len remain 0.
Link: https://lore.kernel.org/r/20210318225632.2481291-1-jollys@google.com
Fixes: 53de092f47 ("scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA")
Tested-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jolly Shah <jollys@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22315a2296 upstream.
After commit 2decad92f4 ("arm64: mte: Ensure TIF_MTE_ASYNC_FAULT is
set atomically"), LLVM's integrated assembler fails to build entry.S:
<instantiation>:5:7: error: expected assembly-time absolute expression
.org . - (664b-663b) + (662b-661b)
^
<instantiation>:6:7: error: expected assembly-time absolute expression
.org . - (662b-661b) + (664b-663b)
^
The root cause is LLVM's assembler has a one-pass design, meaning it
cannot figure out these instruction lengths when the .org directive is
outside of the subsection that they are in, which was changed by the
.arch_extension directive added in the above commit.
Apply the same fix from commit 966a0acce2 ("arm64/alternatives: move
length validation inside the subsection") to the alternative_endif
macro, shuffling the .org directives so that the length validation
happen will always happen in the same subsections. alternative_insn has
not shown any issue yet but it appears that it could have the same issue
in the future so just preemptively change it.
Fixes: f7b93d4294 ("arm64/alternatives: use subsections for replacement sequences")
Cc: <stable@vger.kernel.org> # 5.8.x
Link: https://github.com/ClangBuiltLinux/linux/issues/1347
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c93ac6940 upstream.
This does the directory entry name verification for the legacy
"fillonedir" (and compat) interface that goes all the way back to the
dark ages before we had a proper dirent, and the readdir() system call
returned just a single entry at a time.
Nobody should use this interface unless you still have binaries from
1991, but let's do it right.
This came up during discussions about unsafe_copy_to_user() and proper
checking of all the inputs to it, as the networking layer is looking to
use it in a few new places. So let's make sure the _old_ users do it
all right and proper, before we add new ones.
See also commit 8a23eb804c ("Make filldir[64]() verify the directory
entry filename is valid") which did the proper modern interfaces that
people actually use. It had a note:
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
which this now corrects. Note that we really don't care about POSIX and
the presense of '/' in a directory entry, but verify_dirent_name() also
ends up doing the proper name length verification which is what the
input checking discussion was about.
[ Another option would be to remove the support for this particular very
old interface: any binaries that use it are likely a.out binaries, and
they will no longer run anyway since we removed a.out binftm support
in commit eac6165570 ("x86: Deprecate a.out support").
But I'm not sure which came first: getdents() or ELF support, so let's
pretend somebody might still have a working binary that uses the
legacy readdir() case.. ]
Link: https://lore.kernel.org/lkml/CAHk-=wjbvzCAhAtvG0d81W5o0-KT5PPTHhfJ5ieDFq+bGtgOYg@mail.gmail.com/
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 276559d8d0 upstream.
Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.
Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"
Fixes: 6ecfe51b40 ("Input: refuse to register absolute devices without absinfo")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Tested-by: Juan Garrido <Juan.Garrido@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit daa58c8eec upstream.
The Zenbook Flip entry that was added overwrites a previous one
because of a typo:
In file included from drivers/input/serio/i8042.h:23,
from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
591 | .matches = {
| ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')
Add the missing separator between the two.
Fixes: b5d6e7ab7f ("Input: i8042 - add ASUS Zenbook Flip to noselftest list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd0b455381 ]
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66c3f05ddc ]
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
pci 0000:00:01.0: reg 0x10: [io 0x0000-0x001f]
pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000001f]
...
pcnet32: card has no PCI IO resources, aborting
Use pci_resouce_len() instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cd0f6f576 ]
rport_dev_loss_timedout() sets the rport state to SRP_PORT_LOST and the
SCSI target state to SDEV_TRANSPORT_OFFLINE. If this races with
srp_reconnect_work(), a warning is printed:
Mar 27 18:48:07 ictm1604s01h4 kernel: dev_loss_tmo expired for SRP port-18:1 / host18.
Mar 27 18:48:07 ictm1604s01h4 kernel: ------------[ cut here ]------------
Mar 27 18:48:07 ictm1604s01h4 kernel: scsi_internal_device_block(18:0:0:100) failed: ret = -22
Mar 27 18:48:07 ictm1604s01h4 kernel: Call Trace:
Mar 27 18:48:07 ictm1604s01h4 kernel: ? scsi_target_unblock+0x50/0x50 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: starget_for_each_device+0x80/0xb0 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: target_block+0x24/0x30 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: device_for_each_child+0x57/0x90
Mar 27 18:48:07 ictm1604s01h4 kernel: srp_reconnect_rport+0xe4/0x230 [scsi_transport_srp]
Mar 27 18:48:07 ictm1604s01h4 kernel: srp_reconnect_work+0x40/0xc0 [scsi_transport_srp]
Avoid this by not trying to block targets for rports in SRP_PORT_LOST
state.
Link: https://lore.kernel.org/r/20210401091105.8046-1-mwilck@suse.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7a48c710d ]
When using the driver in I2S TDM mode, the fsl_esai_startup()
function rewrites the number of slots previously set by the
fsl_esai_set_dai_tdm_slot() function to 2.
To fix this, let's use the saved slot count value or, if TDM
is not used and the number of slots is not set, the driver will use
the default value (2), which is set by fsl_esai_probe().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210402081405.9892-1-shc_work@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 844b85dda2 ]
clang warns about an impossible condition when building with 32-bit
phys_addr_t:
arch/arm/mach-keystone/keystone.c:79:16: error: result of comparison of constant 51539607551 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
mem_end > KEYSTONE_HIGH_PHYS_END) {
~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-keystone/keystone.c:78:16: error: result of comparison of constant 34359738368 with expression of type 'phys_addr_t' (aka 'unsigned int') is always true [-Werror,-Wtautological-constant-out-of-range-compare]
if (mem_start < KEYSTONE_HIGH_PHYS_START ||
~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~
Change the temporary variable to a fixed-size u64 to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Link: https://lore.kernel.org/r/20210323131814.2751750-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d47ec7a0a7 ]
After a short network outage, the dst_entry is timed out and put
in DST_OBSOLETE_DEAD. We are in this code because arp reply comes
from this neighbour after network recovers. There is a potential
race condition that dst_entry is still in DST_OBSOLETE_DEAD.
With that, another neighbour lookup causes more harm than good.
In best case all packets in arp_queue are lost. This is
counterproductive to the original goal of finding a better path
for those packets.
I observed a worst case with 4.x kernel where a dst_entry in
DST_OBSOLETE_DEAD state is associated with loopback net_device.
It leads to an ethernet header with all zero addresses.
A packet with all zero source MAC address is quite deadly with
mac80211, ath9k and 802.11 block ack. It fails
ieee80211_find_sta_by_ifaddr in ath9k (xmit.c). Ath9k flushes tx
queue (ath_tx_complete_aggr). BAW (block ack window) is not
updated. BAW logic is damaged and ath9k transmission is disabled.
Signed-off-by: Tong Zhu <zhutong@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46e152186c ]
The copy_to_user() function returns the number of bytes remaining to be
copied, but we want to return -EFAULT if the copy doesn't complete.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77335a0401 ]
Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69d5ff3e9e ]
The driver registers an interrupt handler in _probe, but didn't configure
them until later when the _open function is called. In between, the keypad
can fire an IRQ due to touchpad activity, which the handler ignores. This
causes the kernel to disable the interrupt, blocking the keypad from
working.
Fix this by disabling interrupts before registering the handler.
Additionally, disable them in _close, so that they're only enabled while
open.
Fixes: fc4f314618 ("Input: add TI-Nspire keypad support")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/3383725.iizBOSrK1V@linux-e202.suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b166a20b07 upstream.
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
The bug is fixed by acquiring addr_wq_lock in sctp_destroy_sock
instead of sctp_close.
This addresses CVE-2021-23133.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backport of upstream patch 25da4618af ("xen/events: don't
unmask an event channel when an eoi is pending") introduced a
regression for stable kernels 5.10 and older: setting IRQ affinity for
IRQs related to interdomain events would no longer work, as moving the
IRQ to its new cpu was not included in the irq_ack callback for those
events.
Fix that by adding the needed call.
Note that kernels 5.11 and later don't need the explicit moving of the
IRQ to the target cpu in the irq_ack callback, due to a rework of the
affinity setting in kernel 5.11.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77d02bd00c upstream.
Noticed on a debian:experimental mips and mipsel cross build build
environment:
perfbuilder@ec265a086e9b:~$ mips-linux-gnu-gcc --version | head -1
mips-linux-gnu-gcc (Debian 10.2.1-3) 10.2.1 20201224
perfbuilder@ec265a086e9b:~$
CC /tmp/build/perf/util/map.o
util/map.c: In function 'map__new':
util/map.c:109:5: error: '%s' directive output may be truncated writing between 1 and 2147483645 bytes into a region of size 4096 [-Werror=format-truncation=]
109 | "%s/platforms/%s/arch-%s/usr/lib/%s",
| ^~
In file included from /usr/mips-linux-gnu/include/stdio.h:867,
from util/symbol.h:11,
from util/map.c:2:
/usr/mips-linux-gnu/include/bits/stdio2.h:67:10: note: '__builtin___snprintf_chk' output 32 or more bytes (assuming 4294967321) into a destination of size 4096
67 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
68 | __bos (__s), __fmt, __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Since we have the lenghts for what lands in that place, use it to give
the compiler more info and make it happy.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c056d480b4 upstream
We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.
Fixes: 99cec8a4dd ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3edf5346e4 ]
For multiple split bios, if one of the bio is fail, the whole
should return error to application. But we found there is a race
between bio_integrity_verify_fn and bio complete, which return
io success to application after one of the bio fail. The race as
following:
split bio(READ) kworker
nvme_complete_rq
blk_update_request //split error=0
bio_endio
bio_integrity_endio
queue_work(kintegrityd_wq, &bip->bip_work);
bio_integrity_verify_fn
bio_endio //split bio
__bio_chain_endio
if (!parent->bi_status)
<interrupt entry>
nvme_irq
blk_update_request //parent error=7
req_bio_endio
bio->bi_status = 7 //parent bio
<interrupt exit>
parent->bi_status = 0
parent->bi_end_io() // return bi_status=0
The bio has been split as two: split and parent. When split
bio completed, it depends on kworker to do endio, while
bio_integrity_verify_fn have been interrupted by parent bio
complete irq handler. Then, parent bio->bi_status which have
been set in irq handler will overwrite by kworker.
In fact, even without the above race, we also need to conside
the concurrency beteen mulitple split bio complete and update
the same parent bi_status. Normally, multiple split bios will
be issued to the same hctx and complete from the same irq
vector. But if we have updated queue map between multiple split
bios, these bios may complete on different hw queue and different
irq vector. Then the concurrency update parent bi_status may
cause the final status error.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210331115359.1125679-1-yuyufen@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff132c5f93 ]
Before this patch, gfs2's freeze function failed to report an error
when the target file system was already frozen as it should (and as
generic vfs function freeze_super does. Similarly, gfs2's thaw function
failed to report an error when trying to thaw a file system that is not
frozen, as vfs function thaw_super does. The errors were checked, but
it always returned a 0 return code.
This patch adds the missing error return codes to gfs2 freeze and thaw.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33ce7f2f95 ]
When CONFIG_OF is disabled, building with 'make W=1' produces warnings
about out of bounds array access:
drivers/gpu/drm/imx/imx-ldb.c: In function 'imx_ldb_set_clock.constprop':
drivers/gpu/drm/imx/imx-ldb.c:186:8: error: array subscript -22 is below array bounds of 'struct clk *[4]' [-Werror=array-bounds]
Add an error check before the index is used, which helps with the
warning, as well as any possible other error condition that may be
triggered at runtime.
The warning could be fixed by adding a Kconfig depedency on CONFIG_OF,
but Liu Ying points out that the driver may hit the out-of-bounds
problem at runtime anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d676673d6 ]
Currently we advertise the ID_AA6DFR0_EL1.TRACEVER for the guest,
when the trace register accesses are trapped (CPTR_EL2.TTA == 1).
So, the guest will get an undefined instruction, if trusts the
ID registers and access one of the trace registers.
Lets be nice to the guest and hide the feature to avoid
unexpected behavior.
Even though this can be done at KVM sysreg emulation layer,
we do this by removing the TRACEVER from the sanitised feature
register field. This is fine as long as the ETM drivers
can handle the individual trace units separately, even
when there are differences among the CPUs.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-2-suzuki.poulose@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1165affd48 upstream.
syzbot found general protection fault in crypto_destroy_tfm()[1].
It was caused by wrong clean up loop in llsec_key_alloc().
If one of the tfm array members is in IS_ERR() range it will
cause general protection fault in clean up function [1].
Call Trace:
crypto_free_aead include/crypto/aead.h:191 [inline] [1]
llsec_key_alloc net/mac802154/llsec.c:156 [inline]
mac802154_llsec_key_add+0x9e0/0xcc0 net/mac802154/llsec.c:249
ieee802154_add_llsec_key+0x56/0x80 net/mac802154/cfg.c:338
rdev_add_llsec_key net/ieee802154/rdev-ops.h:260 [inline]
nl802154_add_llsec_key+0x3d3/0x560 net/ieee802154/nl802154.c:1584
genl_family_rcv_msg_doit+0x228/0x320 net/netlink/genetlink.c:739
genl_family_rcv_msg net/netlink/genetlink.c:783 [inline]
genl_rcv_msg+0x328/0x580 net/netlink/genetlink.c:800
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
genl_rcv+0x24/0x40 net/netlink/genetlink.c:811
netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:674
____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
___sys_sendmsg+0xf3/0x170 net/socket.c:2404
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reported-by: syzbot+9ec037722d2603a9f52e@syzkaller.appspotmail.com
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210304152125.1052825-1-paskripkin@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0b96b4a62 upstream.
syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.
backtrace:
[<0000000079d6542a>] kmalloc include/linux/slab.h:552 [inline]
[<0000000079d6542a>] kzalloc include/linux/slab.h:682 [inline]
[<0000000079d6542a>] pcan_usb_fd_init+0x156/0x210 drivers/net/can/usb/peak_usb/pcan_usb_fd.c:868 [2]
[<00000000c09f9057>] peak_usb_create_dev drivers/net/can/usb/peak_usb/pcan_usb_core.c:851 [inline] [1]
[<00000000c09f9057>] peak_usb_probe+0x389/0x490 drivers/net/can/usb/peak_usb/pcan_usb_core.c:949
Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b9fbe1695 upstream.
syzbot reported memory leak in atusb_probe()[1].
The problem was in atusb_alloc_urbs().
Since urb is anchored, we need to release the reference
to correctly free the urb
backtrace:
[<ffffffff82ba0466>] kmalloc include/linux/slab.h:559 [inline]
[<ffffffff82ba0466>] usb_alloc_urb+0x66/0xe0 drivers/usb/core/urb.c:74
[<ffffffff82ad3888>] atusb_alloc_urbs drivers/net/ieee802154/atusb.c:362 [inline][2]
[<ffffffff82ad3888>] atusb_probe+0x158/0x820 drivers/net/ieee802154/atusb.c:1038 [1]
Reported-by: syzbot+28a246747e0a465127f3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46613c9dfa upstream.
usbip_sockfd_store() is invoked when user requests attach (import)
detach (unimport) usb gadget device from usbip host. vhci_hcd sends
import request and usbip_sockfd_store() exports the device if it is
free for export.
Export and unexport are governed by local state and shared state
- Shared state (usbip device status, sockfd) - sockfd and Device
status are used to determine if stub should be brought up or shut
down. Device status is shared between host and client.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- While the device is exported, device status is marked used and socket,
sockfd, and thread pointers are valid.
Export sequence (stub-up) includes validating the socket and creating
receive (rx) and transmit (tx) threads to talk to the client to provide
access to the exported device. rx and tx threads depends on local and
shared state to be correct and in sync.
Unexport (stub-down) sequence shuts the socket down and stops the rx and
tx threads. Stub-down sequence relies on local and shared states to be
in sync.
There are races in updating the local and shared status in the current
stub-up sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to SDEV_ST_USED. This opens up a
race condition between the threads and usbip_sockfd_store() stub up
and down handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold usbip_device lock to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to SDEV_ST_USED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is a
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the stub-up sequence.
Fixes: 9720b4bc76 ("staging/usbip: convert to kthread")
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+bf1a360e305ee719e364@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+95ce4b142579611ef0a9@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/b1c08b983ffa185449c9f0f7d1021dc8c8454b60.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 062b3e1b6d upstream.
The NCSI driver defines a generic ncsi_channel_filter struct that can be
used to store arbitrarily formatted filters, and several generic methods
of accessing data stored in such a filter.
However in both the driver and as defined in the NCSI specification
there are only two actual filters: VLAN ID filters and MAC address
filters. The splitting of the MAC filter into unicast, multicast, and
mixed is also technically not necessary as these are stored in the same
location in hardware.
To save complexity, particularly in the set up and accessing of these
generic filters, remove them in favour of two specific structs. These
can be acted on directly and do not need several generic helper
functions to use.
This also fixes a memory error found by KASAN on ARM32 (which is not
upstream yet), where response handlers accessing a filter's data field
could write past allocated memory.
[ 114.926512] ==================================================================
[ 114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58
[ 114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546
[ 114.947593]
[ 114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13
...
[ 115.170233] The buggy address belongs to the object at 94888540
[ 115.170233] which belongs to the cache kmalloc-32 of size 32
[ 115.181917] The buggy address is located 24 bytes inside of
[ 115.181917] 32-byte region [94888540, 94888560)
[ 115.192115] The buggy address belongs to the page:
[ 115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1
[ 115.204200] flags: 0x100(slab)
[ 115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0
[ 115.215444] page dumped because: kasan: bad access detected
[ 115.221036]
[ 115.222544] Memory state around the buggy address:
[ 115.227384] 94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc
[ 115.233959] 94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc
[ 115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.247077] ^
[ 115.252523] 94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc
[ 115.259093] 94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.265639] ==================================================================
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 955dc68cb9 upstream.
Add a generic netlink family for NCSI. This supports three commands;
NCSI_CMD_PKG_INFO which returns information on packages and their
associated channels, NCSI_CMD_SET_INTERFACE which allows a specific
package or package/channel combination to be set as the preferred
choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04bad8bda9 upstream.
Several response handlers return EBUSY if the data corresponding to the
command/response pair is already set. There is no reason to return an
error here; the channel is advertising something as enabled because we
told it to enable it, and it's possible that the feature has been
enabled previously.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ef8690be1 upstream.
The NCSI driver is mostly silent which becomes a headache when trying to
determine what has occurred on the NCSI connection. This adds additional
logging in a few key areas such as state transitions and calling out
certain errors more visibly.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a14587dfc5 ]
The cited commit wrongly placed log_max_flow_counter field of
mlx5_ifc_flow_table_prop_layout_bits, align it to the HW spec intended
placement.
Fixes: 16f1c5bb3e ("net/mlx5: Check device capability for maximum flow counters")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0687c66b5f ]
The debug_work_activate() is called on the premise that
the work can be inserted, because if wq be in WQ_DRAINING
status, insert work may be failed.
Fixes: e41e704bc4 ("workqueue: improve destroy_workqueue() debuggability")
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7045465500 ]
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_unregister(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used. The patch fixes a logical
bug that hasn't been seen in pratice however it is analogus
to the bug fixed in clk_notifier_register().
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc1 #1
Hardware name: Google Caroline/Caroline,
BIOS Google_Caroline.7820.430.0 07/20/2018
Call Trace:
dump_stack+0xee/0x15c
print_address_description+0x1e/0x2dc
kasan_report+0x188/0x1ce
? clk_notifier_register+0xab/0x230
? clk_prepare_lock+0x15/0x7b
? clk_notifier_register+0xab/0x230
clk_notifier_register+0xab/0x230
dw8250_probe+0xc01/0x10d4
...
Memory state around the buggy address:
ffffffffa0d10480: 00 00 00 00 00 03 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f9 f9
>ffffffffa0d10580: f9 f9 f9 f9 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffffffa0d10600: 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10680: 00 00 00 00 00 00 00 00 f9 f9 f9 f9 00 00 00 00
==================================================================
Fixes: b2476490ef ("clk: introduce the common clock framework")
Reported-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Bartosik <lb@semihalf.com>
Link: https://lore.kernel.org/r/20210401225149.18826-2-lb@semihalf.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3c0c01cb ]
Fix invalid usage of a list_for_each_entry cursor in
clk_notifier_register(). When list is empty or if the list
is completely traversed (without breaking from the loop on one
of the entries) then the list cursor does not point to a valid
entry and therefore should not be used.
The issue was dicovered when running 5.12-rc1 kernel on x86_64
with KASAN enabled:
BUG: KASAN: global-out-of-bounds in clk_notifier_register+0xab/0x230
Read of size 8 at addr ffffffffa0d10588 by task swapper/0/1
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc1 #1
Hardware name: Google Caroline/Caroline,
BIOS Google_Caroline.7820.430.0 07/20/2018
Call Trace:
dump_stack+0xee/0x15c
print_address_description+0x1e/0x2dc
kasan_report+0x188/0x1ce
? clk_notifier_register+0xab/0x230
? clk_prepare_lock+0x15/0x7b
? clk_notifier_register+0xab/0x230
clk_notifier_register+0xab/0x230
dw8250_probe+0xc01/0x10d4
...
Memory state around the buggy address:
ffffffffa0d10480: 00 00 00 00 00 03 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f9 f9
>ffffffffa0d10580: f9 f9 f9 f9 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffffffa0d10600: 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9 00 00 00 00
ffffffffa0d10680: 00 00 00 00 00 00 00 00 f9 f9 f9 f9 00 00 00 00
==================================================================
Fixes: b2476490ef ("clk: introduce the common clock framework")
Reported-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Bartosik <lb@semihalf.com>
Link: https://lore.kernel.org/r/20210401225149.18826-1-lb@semihalf.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 040f31196e ]
When building with W=1, gcc points out that the __packed attribute
on struct qm_eqcr_entry conflicts with the 8-byte alignment
attribute on struct qm_fd inside it:
drivers/soc/fsl/qbman/qman.c:189:1: error: alignment 1 of 'struct qm_eqcr_entry' is less than 8 [-Werror=packed-not-aligned]
I assume that the alignment attribute is the correct one, and
that qm_eqcr_entry cannot actually be unaligned in memory,
so add the same alignment on the outer struct.
Fixes: c535e923bb ("soc/fsl: Introduce DPAA 1.x QMan device driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210323131530.2619900-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0d6e4820 ]
card->owner is a required property and since commit 81033c6b58 ("ALSA:
core: Warn on empty module") a warning is issued if it is empty. Add it.
This fixes following warning observed on Lamobo R1:
WARNING: CPU: 1 PID: 190 at sound/core/init.c:207 snd_card_new+0x430/0x480 [snd]
Modules linked in: sun4i_codec(E+) sun4i_backend(E+) snd_soc_core(E) ...
CPU: 1 PID: 190 Comm: systemd-udevd Tainted: G C E 5.10.0-1-armmp #1 Debian 5.10.4-1
Hardware name: Allwinner sun7i (A20) Family
Call trace:
(snd_card_new [snd])
(snd_soc_bind_card [snd_soc_core])
(snd_soc_register_card [snd_soc_core])
(sun4i_codec_probe [sun4i_codec])
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on early Allwinner SoCs")
Related: commit 3c27ea23ff ("ASoC: qcom: Set card->owner to avoid warnings")
Related: commit ec653df2a0 ("drm/vc4/vc4_hdmi: fill ASoC card owner")
Cc: linux-arm-kernel@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Bastian Germann <bage@linutronix.de>
Link: https://lore.kernel.org/r/20210331151843.30583-1-bage@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03cb4d05b4 ]
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.
Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared. After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.
If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.
Fixes: 0795fb2021 ("net/ncsi: Stop monitor if channel times out or is inactive")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f57011e72f ]
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bf24dc0cc ]
In the if(skb_peek(arrvq) == skb) branch, it calls __skb_dequeue(arrvq) to get
the skb by skb = skb_peek(arrvq). Then __skb_dequeue() unlinks the skb from arrvq
and returns the skb which equals to skb_peek(arrvq). After __skb_dequeue(arrvq)
finished, the skb is freed by kfree_skb(__skb_dequeue(arrvq)) in the first time.
Unfortunately, the same skb is freed in the second time by kfree_skb(skb) after
the branch completed.
My patch removes kfree_skb() in the if(skb_peek(arrvq) == skb) branch, because
this skb will be freed by kfree_skb(skb) finally.
Fixes: cb1b728096 ("tipc: eliminate race condition at multicast reception")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d751350826 ]
Based on the IOMMU configuration, the current cache control settings can
result in possible coherency issues. The hardware team has recommended
new settings for the PCI device path to eliminate the issue.
Fixes: 6f595959c0 ("amd-xgbe: Adjust register settings to improve performance")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b82e75c1 ]
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b6e7088af ]
According to Table 30 ("DVFS_MoniVDAC [6:0] Setting Table") in the
BD9571MWV-M Datasheet Rev. 002, the valid voltage range is 600..1100 mV
(settings 0x3c..0x6e). While the lower limit is taken into account (by
setting regulator_desc.linear_min_sel to 0x3c), the upper limit is not.
Fix this by reducing regulator_desc.n_voltages from 0x80 to 0x6f.
Fixes: e85c5a153f ("regulator: Add ROHM BD9571MWV-M PMIC regulator driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210312130242.3390038-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61431a5907 upstream.
Commit 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.
This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]
This patch resets mac_header earlier, to get more coverage about this change.
Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.
[1]
BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409
CPU: 1 PID: 8409 Comm: syz-executor313 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
dev_parse_header_protocol include/linux/netdevice.h:3177 [inline]
virtio_net_hdr_to_skb.constprop.0+0x99d/0xcd0 include/linux/virtio_net.h:83
packet_snd net/packet/af_packet.c:2994 [inline]
packet_sendmsg+0x2325/0x52b0 net/packet/af_packet.c:3031
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:674
sock_no_sendpage+0xf3/0x130 net/core/sock.c:2860
kernel_sendpage.part.0+0x1ab/0x350 net/socket.c:3631
kernel_sendpage net/socket.c:3628 [inline]
sock_sendpage+0xe5/0x140 net/socket.c:947
pipe_to_sendpage+0x2ad/0x380 fs/splice.c:364
splice_from_pipe_feed fs/splice.c:418 [inline]
__splice_from_pipe+0x43e/0x8a0 fs/splice.c:562
splice_from_pipe fs/splice.c:597 [inline]
generic_splice_sendpage+0xd4/0x140 fs/splice.c:746
do_splice_from fs/splice.c:767 [inline]
do_splice+0xb7e/0x1940 fs/splice.c:1079
__do_splice+0x134/0x250 fs/splice.c:1144
__do_sys_splice fs/splice.c:1350 [inline]
__se_sys_splice fs/splice.c:1332 [inline]
__x64_sys_splice+0x198/0x250 fs/splice.c:1332
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes: 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Balazs Nemeth <bnemeth@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26c56ae67 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df41872b68 upstream.
I encountered a hung task issue, but not a performance one. I run DIO
on a device (need lba continuous, for example open channel ssd), maybe
hungtask in below case:
DIO: Checkpoint:
get addr A(at boundary), merge into BIO,
no submit because boundary missing
flush dirty data(get addr A+1), wait IO(A+1)
writeback timeout, because DIO(A) didn't submit
get addr A+2 fail, because checkpoint is doing
dio_send_cur_page() may clear sdio->boundary, so prevent it from missing
a boundary.
Link: https://lkml.kernel.org/r/20210322042253.38312-1-jack.qiu@huawei.com
Fixes: b1058b9812 ("direct-io: submit bio after boundary buffer is added to it")
Signed-off-by: Jack Qiu <jack.qiu@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90bd070aae upstream.
The following deadlock is detected:
truncate -> setattr path is waiting for pending direct IO to be done (inode->i_dio_count become zero) with inode->i_rwsem held (down_write).
PID: 14827 TASK: ffff881686a9af80 CPU: 20 COMMAND: "ora_p005_hrltd9"
#0 __schedule at ffffffff818667cc
#1 schedule at ffffffff81866de6
#2 inode_dio_wait at ffffffff812a2d04
#3 ocfs2_setattr at ffffffffc05f322e [ocfs2]
#4 notify_change at ffffffff812a5a09
#5 do_truncate at ffffffff812808f5
#6 do_sys_ftruncate.constprop.18 at ffffffff81280cf2
#7 sys_ftruncate at ffffffff81280d8e
#8 do_syscall_64 at ffffffff81003949
#9 entry_SYSCALL_64_after_hwframe at ffffffff81a001ad
dio completion path is going to complete one direct IO (decrement
inode->i_dio_count), but before that it hung at locking inode->i_rwsem:
#0 __schedule+700 at ffffffff818667cc
#1 schedule+54 at ffffffff81866de6
#2 rwsem_down_write_failed+536 at ffffffff8186aa28
#3 call_rwsem_down_write_failed+23 at ffffffff8185a1b7
#4 down_write+45 at ffffffff81869c9d
#5 ocfs2_dio_end_io_write+180 at ffffffffc05d5444 [ocfs2]
#6 ocfs2_dio_end_io+85 at ffffffffc05d5a85 [ocfs2]
#7 dio_complete+140 at ffffffff812c873c
#8 dio_aio_complete_work+25 at ffffffff812c89f9
#9 process_one_work+361 at ffffffff810b1889
#10 worker_thread+77 at ffffffff810b233d
#11 kthread+261 at ffffffff810b7fd5
#12 ret_from_fork+62 at ffffffff81a0035e
Thus above forms ABBA deadlock. The same deadlock was mentioned in
upstream commit 28f5a8a7c0 ("ocfs2: should wait dio before inode lock
in ocfs2_setattr()"). It seems that that commit only removed the
cluster lock (the victim of above dead lock) from the ABBA deadlock
party.
End-user visible effects: Process hang in truncate -> ocfs2_setattr path
and other processes hang at ocfs2_dio_end_io_write path.
This is to fix the deadlock itself. It removes inode_lock() call from
dio completion path to remove the deadlock and add ip_alloc_sem lock in
setattr path to synchronize the inode modifications.
[wen.gang.wang@oracle.com: remove the "had_alloc_lock" as suggested]
Link: https://lkml.kernel.org/r/20210402171344.1605-1-wen.gang.wang@oracle.com
Link: https://lkml.kernel.org/r/20210331203654.3911-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad1e36616 upstream.
ia64 has two stacks:
- memory stack (or stack), pointed at by by r12
- register backing store (register stack), pointed at by
ar.bsp/ar.bspstore with complications around dirty
register frame on CPU.
In [1] Dmitry noticed that PTRACE_GET_SYSCALL_INFO returns the register
stack instead memory stack.
The bug comes from the fact that user_stack_pointer() and
current_user_stack_pointer() don't return the same register:
ulong user_stack_pointer(struct pt_regs *regs) { return regs->ar_bspstore; }
#define current_user_stack_pointer() (current_pt_regs()->r12)
The change gets both back in sync.
I think ptrace(PTRACE_GET_SYSCALL_INFO) is the only affected user by
this bug on ia64.
The change fixes 'rt_sigreturn.gen.test' strace test where it was
observed initially.
Link: https://bugs.gentoo.org/769614 [1]
Link: https://lkml.kernel.org/r/20210331084447.2561532-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 864db232dc upstream.
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5db93e7f upstream.
When sock_wait_state() returns -EINPROGRESS, "sk->sk_state" is
LLCP_CONNECTING. In this case, llcp_sock_connect() is repeatedly invoked,
nfc_llcp_sock_link() will add sk to local->connecting_sockets twice.
sk->sk_node->next will point to itself, that will make an endless loop
and hang-up the system.
To fix it, check whether sk->sk_state is LLCP_CONNECTING in
llcp_sock_connect() to avoid repeated invoking.
Fixes: b4011239a0 ("NFC: llcp: Fix non blocking sockets connections")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.11
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47c5e474bc upstream.
For cases when flexcan is built-in, bitrate is still not set at
registering. So flexcan_chip_freeze() generates:
[ 1.860000] *** ZERO DIVIDE *** FORMAT=4
[ 1.860000] Current process id is 1
[ 1.860000] BAD KERNEL TRAP: 00000000
[ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8
To allow chip freeze, using an hardcoded timeout when bitrate is still
not set.
Fixes: ec15e27cc8 ("can: flexcan: enable RX FIFO after FRZ/HALT valid")
Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.org
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
[mkl: use if instead of ? operator]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Koen Vandeputte <koen.vandeputte@citymesh.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 334ef6ed06 upstream.
While allmodconfig and allyesconfig build for s390 there are also
various bots running compile tests with randconfig, where PCI is
disabled. This reveals that a lot of drivers should actually depend on
HAS_IOMEM.
Adding this to each device driver would be a never ending story,
therefore just disable COMPILE_TEST for s390.
The reasoning is more or less the same as described in
commit bc083a64b6 ("init/Kconfig: make COMPILE_TEST depend on !UML").
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d4d45643 upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 219481a8f9 ]
Make SMB2 not print out an error when an oplock break is received for an
unknown handle, similar to SMB1. The debug message which is printed for
these unknown handles may also be misleading, so fix that too.
The SMB2 lease break path is not affected by this patch.
Without this, a program which writes to a file from one thread, and
opens, reads, and writes the same file from another thread triggers the
below errors several times a minute when run against a Samba server
configured with "smb2 leases = no".
CIFS: VFS: \\192.168.0.1 No task to wake, unknown frame received! NumMids 2
00000000: 424d53fe 00000040 00000000 00000012 .SMB@...........
00000010: 00000001 00000000 ffffffff ffffffff ................
00000020: 00000000 00000000 00000000 00000000 ................
00000030: 00000000 00000000 00000000 00000000 ................
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee8f4f6fc ]
RHBZ: 1933527
Under SMB1 + POSIX, if an inode is reused on a server after we have read and
cached a part of a file, when we then open the new file with the
re-cycled inode there is a chance that we may serve the old data out of cache
to the application.
This only happens for SMB1 (deprecated) and when posix are used.
The simplest solution to avoid this race is to force a revalidate
on smb1-posix open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a419cf49 ]
The sleep warning happens at early boot right at secondary CPU
activation bootup:
smp: Bringing up secondary CPUs ...
BUG: sleeping function called from invalid context at mm/page_alloc.c:4942
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.12.0-rc2-00007-g79e228d0b611-dirty #99
..
Call Trace:
show_stack+0x90/0xc0
dump_stack+0x150/0x1c0
___might_sleep+0x1c0/0x2a0
__might_sleep+0xa0/0x160
__alloc_pages_nodemask+0x1a0/0x600
alloc_page_interleave+0x30/0x1c0
alloc_pages_current+0x2c0/0x340
__get_free_pages+0x30/0xa0
ia64_mca_cpu_init+0x2d0/0x3a0
cpu_init+0x8b0/0x1440
start_secondary+0x60/0x700
start_ap+0x750/0x780
Fixed BSP b0 value from CPU 1
As I understand interrupts are not enabled yet and system has a lot of
memory. There is little chance to sleep and switch to GFP_ATOMIC should
be a no-op.
Link: https://lkml.kernel.org/r/20210315085045.204414-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fcb51c14d ]
The new Ubuntu GCC packages turn on -fcf-protection globally,
which causes a build failure in the x86 realmode code:
cc1: error: ‘-fcf-protection’ is not compatible with this target
Turn it off explicitly on compilers that understand this option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210323124846.1584944-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d677f12ea ]
On many recent ThinkPad laptops, there's a new LED next to the ESC key,
that indicates the FnLock status.
When the Fn+ESC combo is pressed, FnLock is toggled, which causes the
Media Key functionality to change, making it so that the media keys
either perform their media key function, or function as an F-key by
default. The Fn key can be used the access the alternate function at any
time.
With the current linux kernel, the LED doens't change state if you press
the Fn+ESC key combo. However, the media key functionality *does*
change. This is annoying, since the LED will stay on if it was on during
bootup, and it makes it hard to keep track what the current state of the
FnLock is.
This patch calls an ACPI function, that gets the current media key
state, when the Fn+ESC key combo is pressed. Through testing it was
discovered that this function causes the LED to update correctly to
reflect the current state when this function is called.
The relevant ACPI calls are the following:
\_SB_.PCI0.LPC0.EC0_.HKEY.GMKS: Get media key state, returns 0x603 if the FnLock mode is enabled, and 0x602 if it's disabled.
\_SB_.PCI0.LPC0.EC0_.HKEY.SMKS: Set media key state, sending a 1 will enable FnLock mode, and a 0 will disable it.
Relevant discussion:
https://bugzilla.kernel.org/show_bug.cgi?id=207841https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1881015
Signed-off-by: Esteve Varela Colominas <esteve.varela@gmail.com>
Link: https://lore.kernel.org/r/20210315195823.23212-1-esteve.varela@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad48d27a2 ]
We have seen a couple cases where low memory situations cause something
bad to happen, followed by a flood of these messages obscuring the root
cause. Lets ratelimit the dmesg spam so that next time it happens we
don't lose the kernel traces leading up to this.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0571a753cb ]
pxa168_eth_remove() firstly calls unregister_netdev(),
then cancels a timeout work. unregister_netdev() shuts down a device
interface and removes it from the kernel tables. If the timeout occurs
in parallel, the timeout work (pxa168_eth_tx_timeout_task) performs stop
and open of the device. It may lead to an inconsistent state and memory
leaks.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bbce32a20 ]
Without DT aliases, the numbering of mmc interfaces is unpredictable.
Adding them makes it possible to refer to devices consistently. The
popular suggestion to use UUIDs obviously doesn't work with a blank
device fresh from the factory.
See commit fa2d0aa969 ("mmc: core: Allow setting slot index via
device tree alias") for more discussion.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e78836ae76 upstream.
The "u16 CcxRmState[2];" array field in struct "rtllib_network" has 4
bytes in total while the operations performed on this array through-out
the code base are only 2 bytes.
The "CcxRmState" field is fed only 2 bytes of data using memcpy():
(In rtllib_rx.c:1972)
memcpy(network->CcxRmState, &info_element->data[4], 2)
With "info_element->data[]" being a u8 array, if 2 bytes are written
into "CcxRmState" (whose one element is u16 size), then the 2 u8
elements from "data[]" gets squashed and written into the first element
("CcxRmState[0]") while the second element ("CcxRmState[1]") is never
fed with any data.
Same in file rtllib_rx.c:2522:
memcpy(dst->CcxRmState, src->CcxRmState, 2);
The above line duplicates "src" data to "dst" but only writes 2 bytes
(and not 4, which is the actual size). Again, only 1st element gets the
value while the 2nd element remains uninitialized.
This later makes operations done with CcxRmState unpredictable in the
following lines as the 1st element is having a squashed number while the
2nd element is having an uninitialized random number.
rtllib_rx.c:1973: if (network->CcxRmState[0] != 0)
rtllib_rx.c:1977: network->MBssidMask = network->CcxRmState[1] & 0x07;
network->MBssidMask is also of type u8 and not u16.
Fix this by changing the type of "CcxRmState" from u16 to u8 so that the
data written into this array and read from it make sense and are not
random values.
NOTE: The wrong initialization of "CcxRmState" can be seen in the
following commit:
commit ecdfa44610 ("Staging: add Realtek 8192 PCI wireless driver")
The above commit created a file `rtl8192e/ieee80211.h` which used to
have the faulty line. The file has been deleted (or possibly renamed)
with the contents copied in to a new file `rtl8192e/rtllib.h` along with
additional code in the commit 94a799425e (tagged in Fixes).
Fixes: 94a799425e ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek")
Cc: stable@vger.kernel.org
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210323113413.29179-2-atulgopinathan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72ad25fbbb upstream.
The variable "info_element" is of the following type:
struct rtllib_info_element *info_element
defined in drivers/staging/rtl8192e/rtllib.h:
struct rtllib_info_element {
u8 id;
u8 len;
u8 data[];
} __packed;
The "len" field defines the size of the "data[]" array. The code is
supposed to check if "info_element->len" is greater than 4 and later
equal to 6. If this is satisfied then, the last two bytes (the 4th and
5th element of u8 "data[]" array) are copied into "network->CcxRmState".
Right now the code uses "memcpy()" with the source as "&info_element[4]"
which would copy in wrong and unintended information. The struct
"rtllib_info_element" has a size of 2 bytes for "id" and "len",
therefore indexing will be done in interval of 2 bytes. So,
"info_element[4]" would point to data which is beyond the memory
allocated for this pointer (that is, at x+8, while "info_element" has
been allocated only from x to x+7 (2 + 6 => 8 bytes)).
This patch rectifies this error by using "&info_element->data[4]" which
correctly copies the last two bytes of "data[]".
NOTE: The faulty line of code came from the following commit:
commit ecdfa44610 ("Staging: add Realtek 8192 PCI wireless driver")
The above commit created the file `rtl8192e/ieee80211/ieee80211_rx.c`
which had the faulty line of code. This file has been deleted (or
possibly renamed) with the contents copied in to a new file
`rtl8192e/rtllib_rx.c` along with additional code in the commit
94a799425e (tagged in Fixes).
Fixes: 94a799425e ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek")
Cc: stable@vger.kernel.org
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210323113413.29179-1-atulgopinathan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72035f4954 upstream.
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool.
however, dev->dev is actually set after calling init_dma_pools(), which
effectively makes dma_pool_create(..NULL) and cause crash.
To fix this issue, init dma only after dev->dev is set.
[ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290
[ 1.323257] Call Trace:
[ 1.323390] ? pci_write_config_word+0x27/0x30
[ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core]
[ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci]
Fixes: 7c51247a1f (usb: gadget: udc: Provide correct arguments for 'dma_pool_create')
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bd860493f upstream.
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 829933ef05 ]
For each device, the nosy driver allocates a pcilynx structure.
A use-after-free might happen in the following scenario:
1. Open nosy device for the first time and call ioctl with command
NOSY_IOC_START, then a new client A will be malloced and added to
doubly linked list.
2. Open nosy device for the second time and call ioctl with command
NOSY_IOC_START, then a new client B will be malloced and added to
doubly linked list.
3. Call ioctl with command NOSY_IOC_START for client A, then client A
will be readded to the doubly linked list. Now the doubly linked
list is messed up.
4. Close the first nosy device and nosy_release will be called. In
nosy_release, client A will be unlinked and freed.
5. Close the second nosy device, and client A will be referenced,
resulting in UAF.
The root cause of this bug is that the element in the doubly linked list
is reentered into the list.
Fix this bug by adding a check before inserting a client. If a client
is already in the linked list, don't insert it.
The following KASAN report reveals it:
BUG: KASAN: use-after-free in nosy_release+0x1ea/0x210
Write of size 8 at addr ffff888102ad7360 by task poc
CPU: 3 PID: 337 Comm: poc Not tainted 5.12.0-rc5+ #6
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
nosy_release+0x1ea/0x210
__fput+0x1e2/0x840
task_work_run+0xe8/0x180
exit_to_user_mode_prepare+0x114/0x120
syscall_exit_to_user_mode+0x1d/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Allocated by task 337:
nosy_open+0x154/0x4d0
misc_open+0x2ec/0x410
chrdev_open+0x20d/0x5a0
do_dentry_open+0x40f/0xe80
path_openat+0x1cf9/0x37b0
do_filp_open+0x16d/0x390
do_sys_openat2+0x11d/0x360
__x64_sys_open+0xfd/0x1a0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Freed by task 337:
kfree+0x8f/0x210
nosy_release+0x158/0x210
__fput+0x1e2/0x840
task_work_run+0xe8/0x180
exit_to_user_mode_prepare+0x114/0x120
syscall_exit_to_user_mode+0x1d/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff888102ad7300 which belongs to the cache kmalloc-128 of size 128
The buggy address is located 96 bytes inside of 128-byte region [ffff888102ad7300, ffff888102ad7380)
[ Modified to use 'list_empty()' inside proper lock - Linus ]
Link: https://lore.kernel.org/lkml/1617433116-5930-1-git-send-email-zheyuma97@gmail.com/
Reported-and-tested-by: 马哲宇 (Zheyu Ma) <zheyuma97@gmail.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3bdd1c314 ]
When devm_kcalloc() fails, we should execute device_unregister()
to unregister edev->dev from system.
Fixes: 046050f6e6 ("extcon: Update the prototype of extcon_register_notifier() with enum extcon")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9570d4a5e ]
Add stubs for extcon_register_notifier_all() function for !CONFIG_EXTCON
case. This is useful for compile testing and for drivers which use
EXTCON but do not require it (therefore do not depend on CONFIG_EXTCON).
Fixes: 815429b39d ("extcon: Add new extcon_register_notifier_all() to monitor all external connectors")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0b3d6e6f2d upstream.
Since commit a983b5ebee ("mm: memcontrol: fix excessive complexity in
memory.stat reporting") memcg dirty and writeback counters are managed
as:
1) per-memcg per-cpu values in range of [-32..32]
2) per-memcg atomic counter
When a per-cpu counter cannot fit in [-32..32] it's flushed to the
atomic. Stat readers only check the atomic. Thus readers such as
balance_dirty_pages() may see a nontrivial error margin: 32 pages per
cpu.
Assuming 100 cpus:
4k x86 page_size: 13 MiB error per memcg
64k ppc page_size: 200 MiB error per memcg
Considering that dirty+writeback are used together for some decisions the
errors double.
This inaccuracy can lead to undeserved oom kills. One nasty case is
when all per-cpu counters hold positive values offsetting an atomic
negative value (i.e. per_cpu[*]=32, atomic=n_cpu*-32).
balance_dirty_pages() only consults the atomic and does not consider
throttling the next n_cpu*32 dirty pages. If the file_lru is in the
13..200 MiB range then there's absolutely no dirty throttling, which
burdens vmscan with only dirty+writeback pages thus resorting to oom
kill.
It could be argued that tiny containers are not supported, but it's more
subtle. It's the amount the space available for file lru that matters.
If a container has memory.max-200MiB of non reclaimable memory, then it
will also suffer such oom kills on a 100 cpu machine.
The following test reliably ooms without this patch. This patch avoids
oom kills.
$ cat test
mount -t cgroup2 none /dev/cgroup
cd /dev/cgroup
echo +io +memory > cgroup.subtree_control
mkdir test
cd test
echo 10M > memory.max
(echo $BASHPID > cgroup.procs && exec /memcg-writeback-stress /foo)
(echo $BASHPID > cgroup.procs && exec dd if=/dev/zero of=/foo bs=2M count=100)
$ cat memcg-writeback-stress.c
/*
* Dirty pages from all but one cpu.
* Clean pages from the non dirtying cpu.
* This is to stress per cpu counter imbalance.
* On a 100 cpu machine:
* - per memcg per cpu dirty count is 32 pages for each of 99 cpus
* - per memcg atomic is -99*32 pages
* - thus the complete dirty limit: sum of all counters 0
* - balance_dirty_pages() only sees atomic count -99*32 pages, which
* it max()s to 0.
* - So a workload can dirty -99*32 pages before balance_dirty_pages()
* cares.
*/
#define _GNU_SOURCE
#include <err.h>
#include <fcntl.h>
#include <sched.h>
#include <stdlib.h>
#include <stdio.h>
#include <sys/stat.h>
#include <sys/sysinfo.h>
#include <sys/types.h>
#include <unistd.h>
static char *buf;
static int bufSize;
static void set_affinity(int cpu)
{
cpu_set_t affinity;
CPU_ZERO(&affinity);
CPU_SET(cpu, &affinity);
if (sched_setaffinity(0, sizeof(affinity), &affinity))
err(1, "sched_setaffinity");
}
static void dirty_on(int output_fd, int cpu)
{
int i, wrote;
set_affinity(cpu);
for (i = 0; i < 32; i++) {
for (wrote = 0; wrote < bufSize; ) {
int ret = write(output_fd, buf+wrote, bufSize-wrote);
if (ret == -1)
err(1, "write");
wrote += ret;
}
}
}
int main(int argc, char **argv)
{
int cpu, flush_cpu = 1, output_fd;
const char *output;
if (argc != 2)
errx(1, "usage: output_file");
output = argv[1];
bufSize = getpagesize();
buf = malloc(getpagesize());
if (buf == NULL)
errx(1, "malloc failed");
output_fd = open(output, O_CREAT|O_RDWR);
if (output_fd == -1)
err(1, "open(%s)", output);
for (cpu = 0; cpu < get_nprocs(); cpu++) {
if (cpu != flush_cpu)
dirty_on(output_fd, cpu);
}
set_affinity(flush_cpu);
if (fsync(output_fd))
err(1, "fsync(%s)", output);
if (close(output_fd))
err(1, "close(%s)", output);
free(buf);
}
Make balance_dirty_pages() and wb_over_bg_thresh() work harder to
collect exact per memcg counters. This avoids the aforementioned oom
kills.
This does not affect the overhead of memory.stat, which still reads the
single atomic counter.
Why not use percpu_counter? memcg already handles cpus going offline, so
no need for that overhead from percpu_counter. And the percpu_counter
spinlocks are more heavyweight than is required.
It probably also makes sense to use exact dirty and writeback counters
in memcg oom reports. But that is saved for later.
Link: http://lkml.kernel.org/r/20190329174609.164344-1-gthelen@google.com
Signed-off-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org> [4.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe6bdfc8e1 upstream.
Commit e27be240df ("mm: memcg: make sure memory.events is uptodate
when waking pollers") converted most of memcg event counters to
per-memcg atomics, which made them less confusing for a user. The
"oom_kill" counter remained untouched, so now it behaves differently
than other counters (including "oom"). This adds nothing but confusion.
Let's fix this by adding the MEMCG_OOM_KILL event, and follow the
MEMCG_OOM approach.
This also removes a hack from count_memcg_event_mm(), introduced earlier
specially for the OOM_KILL counter.
[akpm@linux-foundation.org: fix for droppage of memcg-replace-mm-owner-with-mm-memcg.patch]
Link: http://lkml.kernel.org/r/20180508124637.29984-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[fllinden@amazon.com: backport to 4.14, minor contextual changes]
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e81bf9793b upstream.
The LKP robot found a 27% will-it-scale/page_fault3 performance
regression regarding commit e27be240df53("mm: memcg: make sure
memory.events is uptodate when waking pollers").
What the test does is:
1 mkstemp() a 128M file on a tmpfs;
2 start $nr_cpu processes, each to loop the following:
2.1 mmap() this file in shared write mode;
2.2 write 0 to this file in a PAGE_SIZE step till the end of the file;
2.3 unmap() this file and repeat this process.
3 After 5 minutes, check how many loops they managed to complete, the
higher the better.
The commit itself looks innocent enough as it merely changed some event
counting mechanism and this test didn't trigger those events at all.
Perf shows increased cycles spent on accessing root_mem_cgroup->stat_cpu
in count_memcg_event_mm()(called by handle_mm_fault()) and in
__mod_memcg_state() called by page_add_file_rmap(). So it's likely due
to the changed layout of 'struct mem_cgroup' that either make stat_cpu
falling into a constantly modifying cacheline or some hot fields stop
being in the same cacheline.
I verified this by moving memory_events[] back to where it was:
: --- a/include/linux/memcontrol.h
: +++ b/include/linux/memcontrol.h
: @@ -205,7 +205,6 @@ struct mem_cgroup {
: int oom_kill_disable;
:
: /* memory.events */
: - atomic_long_t memory_events[MEMCG_NR_MEMORY_EVENTS];
: struct cgroup_file events_file;
:
: /* protect arrays of thresholds */
: @@ -238,6 +237,7 @@ struct mem_cgroup {
: struct mem_cgroup_stat_cpu __percpu *stat_cpu;
: atomic_long_t stat[MEMCG_NR_STAT];
: atomic_long_t events[NR_VM_EVENT_ITEMS];
: + atomic_long_t memory_events[MEMCG_NR_MEMORY_EVENTS];
:
: unsigned long socket_pressure;
And performance restored.
Later investigation found that as long as the following 3 fields
moving_account, move_lock_task and stat_cpu are in the same cacheline,
performance will be good. To avoid future performance surprise by other
commits changing the layout of 'struct mem_cgroup', this patch makes
sure the 3 fields stay in the same cacheline.
One concern of this approach is, moving_account and move_lock_task could
be modified when a process changes memory cgroup while stat_cpu is a
always read field, it might hurt to place them in the same cacheline. I
assume it is rare for a process to change memory cgroup so this should
be OK.
Link: https://lkml.kernel.org/r/20180528114019.GF9904@yexl-desktop
Link: http://lkml.kernel.org/r/20180601071115.GA27302@intel.com
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e27be240df upstream.
Commit a983b5ebee ("mm: memcontrol: fix excessive complexity in
memory.stat reporting") added per-cpu drift to all memory cgroup stats
and events shown in memory.stat and memory.events.
For memory.stat this is acceptable. But memory.events issues file
notifications, and somebody polling the file for changes will be
confused when the counters in it are unchanged after a wakeup.
Luckily, the events in memory.events - MEMCG_LOW, MEMCG_HIGH, MEMCG_MAX,
MEMCG_OOM - are sufficiently rare and high-level that we don't need
per-cpu buffering for them: MEMCG_HIGH and MEMCG_MAX would be the most
frequent, but they're counting invocations of reclaim, which is a
complex operation that touches many shared cachelines.
This splits memory.events from the generic VM events and tracks them in
their own, unbuffered atomic counters. That's also cleaner, as it
eliminates the ugly enum nesting of VM and cgroup events.
[hannes@cmpxchg.org: "array subscript is above array bounds"]
Link: http://lkml.kernel.org/r/20180406155441.GA20806@cmpxchg.org
Link: http://lkml.kernel.org/r/20180405175507.GA24817@cmpxchg.org
Fixes: a983b5ebee ("mm: memcontrol: fix excessive complexity in memory.stat reporting")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c3cc39118c upstream.
After commit a983b5ebee ("mm: memcontrol: fix excessive complexity in
memory.stat reporting"), we observed slowly upward creeping NR_WRITEBACK
counts over the course of several days, both the per-memcg stats as well
as the system counter in e.g. /proc/meminfo.
The conversion from full per-cpu stat counts to per-cpu cached atomic
stat counts introduced an irq-unsafe RMW operation into the updates.
Most stat updates come from process context, but one notable exception
is the NR_WRITEBACK counter. While writebacks are issued from process
context, they are retired from (soft)irq context.
When writeback completions interrupt the RMW counter updates of new
writebacks being issued, the decs from the completions are lost.
Since the global updates are routed through the joint lruvec API, both
the memcg counters as well as the system counters are affected.
This patch makes the joint stat and event API irq safe.
Link: http://lkml.kernel.org/r/20180203082353.17284-1-hannes@cmpxchg.org
Fixes: a983b5ebee ("mm: memcontrol: fix excessive complexity in memory.stat reporting")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Debugged-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5e46d1b78a upstream.
syzbot is reporting NULL pointer dereference at reiserfs_security_init()
[1], for commit ab17c4f021 ("reiserfs: fixup xattr_root caching")
is assuming that REISERFS_SB(s)->xattr_root != NULL in
reiserfs_xattr_jcreate_nblocks() despite that commit made
REISERFS_SB(sb)->priv_root != NULL && REISERFS_SB(s)->xattr_root == NULL
case possible.
I guess that commit 6cb4aff0a7 ("reiserfs: fix oops while creating
privroot with selinux enabled") wanted to check xattr_root != NULL
before reiserfs_xattr_jcreate_nblocks(), for the changelog is talking
about the xattr root.
The issue is that while creating the privroot during mount
reiserfs_security_init calls reiserfs_xattr_jcreate_nblocks which
dereferences the xattr root. The xattr root doesn't exist, so we get
an oops.
Therefore, update reiserfs_xattrs_initialized() to check both the
privroot and the xattr root.
Link: https://syzkaller.appspot.com/bug?id=8abaedbdeb32c861dc5340544284167dd0e46cde # [1]
Reported-and-tested-by: syzbot <syzbot+690cb1e51970435f9775@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 6cb4aff0a7 ("reiserfs: fix oops while creating privroot with selinux enabled")
Acked-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e720e7d0e9 upstream.
There are code paths that rely on zero_pfn to be fully initialized
before core_initcall. For example, wq_sysfs_init() is a core_initcall
function that eventually results in a call to kernel_execve, which
causes a page fault with a subsequent mmput. If zero_pfn is not
initialized by then it may not get cleaned up properly and result in an
error:
BUG: Bad rss-counter state mm:(ptrval) type:MM_ANONPAGES val:1
Here is an analysis of the race as seen on a MIPS device. On this
particular MT7621 device (Ubiquiti ER-X), zero_pfn is PFN 0 until
initialized, at which point it becomes PFN 5120:
1. wq_sysfs_init calls into kobject_uevent_env at core_initcall:
kobject_uevent_env+0x7e4/0x7ec
kset_register+0x68/0x88
bus_register+0xdc/0x34c
subsys_virtual_register+0x34/0x78
wq_sysfs_init+0x1c/0x4c
do_one_initcall+0x50/0x1a8
kernel_init_freeable+0x230/0x2c8
kernel_init+0x10/0x100
ret_from_kernel_thread+0x14/0x1c
2. kobject_uevent_env() calls call_usermodehelper_exec() which executes
kernel_execve asynchronously.
3. Memory allocations in kernel_execve cause a page fault, bumping the
MM reference counter:
add_mm_counter_fast+0xb4/0xc0
handle_mm_fault+0x6e4/0xea0
__get_user_pages.part.78+0x190/0x37c
__get_user_pages_remote+0x128/0x360
get_arg_page+0x34/0xa0
copy_string_kernel+0x194/0x2a4
kernel_execve+0x11c/0x298
call_usermodehelper_exec_async+0x114/0x194
4. In case zero_pfn has not been initialized yet, zap_pte_range does
not decrement the MM_ANONPAGES RSS counter and the BUG message is
triggered shortly afterwards when __mmdrop checks the ref counters:
__mmdrop+0x98/0x1d0
free_bprm+0x44/0x118
kernel_execve+0x160/0x1d8
call_usermodehelper_exec_async+0x114/0x194
ret_from_kernel_thread+0x14/0x1c
To avoid races such as described above, initialize init_zero_pfn at
early_initcall level. Depending on the architecture, ZERO_PAGE is
either constant or gets initialized even earlier, at paging_init, so
there is no issue with initializing zero_pfn earlier.
Link: https://lkml.kernel.org/r/CALCv0x2YqOXEAy2Q=hafjhHCtTHVodChv1qpM=niAXOpqEbt7w@mail.gmail.com
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: stable@vger.kernel.org
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9deb193af6 upstream.
Commit cbc3b92ce0 fixed an issue to modify the macros of the stack trace
event so that user space could parse it properly. Originally the stack
trace format to user space showed that the called stack was a dynamic
array. But it is not actually a dynamic array, in the way that other
dynamic event arrays worked, and this broke user space parsing for it. The
update was to make the array look to have 8 entries in it. Helper
functions were added to make it parse it correctly, as the stack was
dynamic, but was determined by the size of the event stored.
Although this fixed user space on how it read the event, it changed the
internal structure used for the stack trace event. It changed the array
size from [0] to [8] (added 8 entries). This increased the size of the
stack trace event by 8 words. The size reserved on the ring buffer was the
size of the stack trace event plus the number of stack entries found in
the stack trace. That commit caused the amount to be 8 more than what was
needed because it did not expect the caller field to have any size. This
produced 8 entries of garbage (and reading random data) from the stack
trace event:
<idle>-0 [002] d... 1976396.837549: <stack trace>
=> trace_event_raw_event_sched_switch
=> __traceiter_sched_switch
=> __schedule
=> schedule_idle
=> do_idle
=> cpu_startup_entry
=> secondary_startup_64_no_verify
=> 0xc8c5e150ffff93de
=> 0xffff93de
=> 0
=> 0
=> 0xc8c5e17800000000
=> 0x1f30affff93de
=> 0x00000004
=> 0x200000000
Instead, subtract the size of the caller field from the size of the event
to make sure that only the amount needed to store the stack trace is
reserved.
Link: https://lore.kernel.org/lkml/your-ad-here.call-01617191565-ext-9692@work.hours/
Cc: stable@vger.kernel.org
Fixes: cbc3b92ce0 ("tracing: Set kernel_stack's caller size properly")
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Tested-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54f30befa upstream.
We found the alc_update_headset_mode() is not called on some machines
when unplugging the headset, as a result, the mode of the
ALC_HEADSET_MODE_UNPLUGGED can't be set, then the current_headset_type
is not cleared, if users plug a differnt type of headset next time,
the determine_headset_type() will not be called and the audio jack is
set to the headset type of previous time.
On the Dell machines which connect the dmic to the PCH, if we open
the gnome-sound-setting and unplug the headset, this issue will
happen. Those machines disable the auto-mute by ucm and has no
internal mic in the input source, so the update_headset_mode() will
not be called by cap_sync_hook or automute_hook when unplugging, and
because the gnome-sound-setting is opened, the codec will not enter
the runtime_suspend state, so the update_headset_mode() will not be
called by alc_resume when unplugging. In this case the
hp_automute_hook is called when unplugging, so add
update_headset_mode() calling to this function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210320091542.6748-2-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit febf225655 upstream.
We found a recording issue on a Dell AIO, users plug a headset-mic and
select headset-mic from UI, but can't record any sound from
headset-mic. The root cause is the determine_headset_type() returns a
wrong type, e.g. users plug a ctia type headset, but that function
returns omtp type.
On this machine, the internal mic is not connected to the codec, the
"Input Source" is headset mic by default. And when users plug a
headset, the determine_headset_type() will be called immediately, the
codec on this AIO is alc274, the delay time for this codec in the
determine_headset_type() is only 80ms, the delay is too short to
correctly determine the headset type, the fail rate is nearly 99% when
users plug the headset with the normal speed.
Other codecs set several hundred ms delay time, so here I change the
delay time to 850ms for alc2x4 series, after this change, the fail
rate is zero unless users plug the headset slowly on purpose.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210320091542.6748-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6306c1189e upstream.
Multiple BPF-helpers that can manipulate/increase the size of the SKB uses
__bpf_skb_max_len() as the max-length. This function limit size against
the current net_device MTU (skb->dev->mtu).
When a BPF-prog grow the packet size, then it should not be limited to the
MTU. The MTU is a transmit limitation, and software receiving this packet
should be allowed to increase the size. Further more, current MTU check in
__bpf_skb_max_len uses the MTU from ingress/current net_device, which in
case of redirects uses the wrong net_device.
This patch keeps a sanity max limit of SKB_MAX_ALLOC (16KiB). The real limit
is elsewhere in the system. Jesper's testing[1] showed it was not possible
to exceed 8KiB when expanding the SKB size via BPF-helper. The limiting
factor is the define KMALLOC_MAX_CACHE_SIZE which is 8192 for
SLUB-allocator (CONFIG_SLUB) in-case PAGE_SIZE is 4096. This define is
in-effect due to this being called from softirq context see code
__gfp_pfmemalloc_flags() and __do_kmalloc_node(). Jakub's testing showed
that frames above 16KiB can cause NICs to reset (but not crash). Keep this
sanity limit at this level as memory layer can differ based on kernel
config.
[1] https://github.com/xdp-project/bpf-examples/tree/master/MTU-tests
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161287788936.790810.2937823995775097177.stgit@firesoul
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39935dccb2 ]
If a DDP broadcast packet is sent out to a non-gateway target, it is
also looped back. There is a potential for the loopback device to have a
longer hardware header length than the original target route's device,
which can result in the skb not being created with enough room for the
loopback device's hardware header. This patch fixes the issue by
determining that a loopback will be necessary prior to allocating the
skb, and if so, ensuring the skb has enough room.
This was discovered while testing a new driver that creates a LocalTalk
network interface (LTALK_HLEN = 1). It caused an skb_under_panic.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a28af7a3e ]
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e862a3e408 ]
This ensure that previous association attempts do not leave stale statuses
on subsequent attempts.
This fixes the WARN_ON(!cr->bss)) from __cfg80211_connect_result() when
connecting to an AP after a previous connection failure (e.g. where EAP fails
due to incorrect psk but association succeeded). In some scenarios, indeed,
brcmf_is_linkup() was reporting a link up event too early due to stale
BRCMF_VIF_STATUS_ASSOC_SUCCESS bit, thus reporting to cfg80211 a connection
result with a zeroed bssid (vif->profile.bssid is still empty), causing the
WARN_ON due to the call to cfg80211_get_bss() with the empty bssid.
Signed-off-by: Luca Pesce <luca.pesce@vimar.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608807119-21785-1-git-send-email-luca.pesce@vimar.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dccdc5a19 ]
In ext4_rename(), when RENAME_WHITEOUT failed to add new entry into
directory, it ends up dropping new created whiteout inode under the
running transaction. After commit <9b88f9fb0d2> ("ext4: Do not iput inode
under running transaction"), we follow the assumptions that evict() does
not get called from a transaction context but in ext4_rename() it breaks
this suggestion. Although it's not a real problem, better to obey it, so
this patch add inode to orphan list and stop transaction before final
iput().
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210303131703.330415-2-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2d106fe3b ]
request_irq() wont accept a name which contains slash so we need to
repalce it with something else -- otherwise it will trigger a warning
and the entry in /proc/irq/ will not be created
since the .name might be used by userspace and we don't want to break
userspace, so we are changing the parameters passed to request_irq()
[ 1.565966] name 'pci-das6402/16'
[ 1.566149] WARNING: CPU: 0 PID: 184 at fs/proc/generic.c:180 __xlate_proc_name+0x93/0xb0
[ 1.568923] RIP: 0010:__xlate_proc_name+0x93/0xb0
[ 1.574200] Call Trace:
[ 1.574722] proc_mkdir+0x18/0x20
[ 1.576629] request_threaded_irq+0xfe/0x160
[ 1.576859] auto_attach+0x60a/0xc40 [cb_pcidas64]
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210315195814.4692-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5848a3d8 ]
request_irq() wont accept a name which contains slash so we need to
repalce it with something else -- otherwise it will trigger a warning
and the entry in /proc/irq/ will not be created
since the .name might be used by userspace and we don't want to break
userspace, so we are changing the parameters passed to request_irq()
[ 1.630764] name 'pci-das1602/16'
[ 1.630950] WARNING: CPU: 0 PID: 181 at fs/proc/generic.c:180 __xlate_proc_name+0x93/0xb0
[ 1.634009] RIP: 0010:__xlate_proc_name+0x93/0xb0
[ 1.639441] Call Trace:
[ 1.639976] proc_mkdir+0x18/0x20
[ 1.641946] request_threaded_irq+0xfe/0x160
[ 1.642186] cb_pcidas_auto_attach+0xf4/0x610 [cb_pcidas]
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210315195914.4801-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb691e69f ]
vhost_reset_is_le() is vhost_init_is_le(), and in the case of
cross-endian legacy, vhost_init_is_le() depends on vq->user_be.
vq->user_be is set by vhost_disable_cross_endian().
But in vhost_vq_reset(), we have:
vhost_reset_is_le(vq);
vhost_disable_cross_endian(vq);
And so user_be is used before being set.
To fix that, reverse the lines order as there is no other dependency
between them.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://lore.kernel.org/r/20210312140913.788592-1-lvivier@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed5fae005 ]
The code relies on constant folding of cpu_has_feature() based
on possible and always true values as defined per
CPU_FTRS_ALWAYS and CPU_FTRS_POSSIBLE.
Build failure is encountered with for instance
book3e_all_defconfig on kisskb in the AMDGPU driver which uses
cpu_has_feature(CPU_FTR_VSX_COMP) to decide whether calling
kernel_enable_vsx() or not.
The failure is due to cpu_has_feature() not being inlined with
that configuration with gcc 4.9.
In the same way as commit acdad8fb4a ("powerpc: Force inlining of
mmu_has_feature to fix build failure"), for inlining of
cpu_has_feature().
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b231dfa040ce4cc37f702f5c3a595fdeabfe0462.1615378209.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb18c67875 ]
Most steps in this table are steps of 3dB (300 centi-dB), so we can
simplify the table.
This not only reduces the amount of space it takes inside the kernel,
this also makes alsa-lib's mixer code actually accept the table, where
as before this change alsa-lib saw the "ADC PGA Gain" control as a
control without a dB scale.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210228160441.241110-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f86f58e359 ]
According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has
the following bit field definitions:
| BITS | FIELD | RW | RESET | DEFINITION |
| 15 | RSVD | RO | 0x0 | Reserved |
| 14 | RSVD | RW | 0x1 | Reserved |
| 13:12 | MAX_GAIN | RW | 0x1 | Max Gain of AVC in expander mode |
| 11:10 | RSVD | RO | 0x0 | Reserved |
| 9:8 | LBI_RESP | RW | 0x1 | Integrator Response |
| 7:6 | RSVD | RO | 0x0 | Reserved |
| 5 | HARD_LMT_EN | RW | 0x0 | Enable hard limiter mode |
| 4:1 | RSVD | RO | 0x0 | Reserved |
| 0 | EN | RW | 0x0 | Enable/Disable AVC |
The original default value written to the DAP_AVC_CTRL register during
sgtl5000_i2c_probe() was 0x0510. This would incorrectly write values to
bits 4 and 10, which are defined as RESERVED. It would also not set
bits 12 and 14 to their correct RESET values of 0x1, and instead set
them to 0x0. While the DAP_AVC module is effectively disabled because
the EN bit is 0, this default value is still writing invalid values to
registers that are marked as read-only and RESERVED as well as not
setting bits 12 and 14 to their correct default values as defined by the
datasheet.
The correct value that should be written to the DAP_AVC_CTRL register is
0x5100, which configures the register bits to the default values defined
by the datasheet, and prevents any writes to bits defined as
'read-only'. Generally speaking, it is best practice to NOT attempt to
write values to registers/bits defined as RESERVED, as it generally
produces unwanted/undefined behavior, or errors.
Also, all credit for this patch should go to my colleague Dan MacDonald
<dmacdonald@curbellmedical.com> for finding this error in the first
place.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Benjamin Rood <benjaminjrood@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-dev
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eee51df776 ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b5 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfa26ed1f9 ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b5 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ddc942394 ]
I think this is unlikely but possible:
svc_authenticate sets rq_authop and calls svcauth_gss_accept. The
kmalloc(sizeof(*svcdata), GFP_KERNEL) fails, leaving rq_auth_data NULL,
and returning SVC_DENIED.
This causes svc_process_common to go to err_bad_auth, and eventually
call svc_authorise. That calls ->release == svcauth_gss_release, which
tries to dereference rq_auth_data.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Link: https://lore.kernel.org/linux-nfs/3F1B347F-B809-478F-A1E9-0BE98E22B0F0@oracle.com/T/#t
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcc32f4f18 ]
This reverts commit 6af1799aaf.
Commit 6af1799aaf ("ipv6: drop incoming packets having a v4mapped
source address") introduced an input check against v4mapped addresses.
Use of such addresses on the wire is indeed questionable and not
allowed on public Internet. As the commit pointed out
https://tools.ietf.org/html/draft-itojun-v6ops-v4mapped-harmful-02
lists potential issues.
Unfortunately there are applications which use v4mapped addresses,
and breaking them is a clear regression. For example v4mapped
addresses (or any semi-valid addresses, really) may be used
for uni-direction event streams or packet export.
Since the issue which sparked the addition of the check was with
TCP and request_socks in particular push the check down to TCPv6
and DCCP. This restores the ability to receive UDPv6 packets with
v4mapped address as the source.
Keep using the IPSTATS_MIB_INHDRERRORS statistic to minimize the
user-visible changes.
Fixes: 6af1799aaf ("ipv6: drop incoming packets having a v4mapped source address")
Reported-by: Sunyi Shao <sunyishao@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f935e8e72 ]
For AF_VSOCK, accept() currently returns sockets that are unlabelled.
Other socket families derive the child's SID from the SID of the parent
and the SID of the incoming packet. This is typically done as the
connected socket is placed in the queue that accept() removes from.
Reuse the existing 'security_sk_clone' hook to copy the SID from the
parent (server) socket to the child. There is no packet SID in this
case.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: David Brazdil <dbrazdil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a846738f8c upstream.
The fix for XSA-365 zapped too many of the ->persistent_gnt[] entries.
Ones successfully obtained should not be overwritten, but instead left
for xen_blkbk_unmap_prepare() to pick up and put.
This is XSA-371.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 163f0ec1df upstream.
Syzbot is reporting that ext4 can enter fs reclaim from kvmalloc() while
the transaction is started like:
fs_reclaim_acquire+0x117/0x150 mm/page_alloc.c:4340
might_alloc include/linux/sched/mm.h:193 [inline]
slab_pre_alloc_hook mm/slab.h:493 [inline]
slab_alloc_node mm/slub.c:2817 [inline]
__kmalloc_node+0x5f/0x430 mm/slub.c:4015
kmalloc_node include/linux/slab.h:575 [inline]
kvmalloc_node+0x61/0xf0 mm/util.c:587
kvmalloc include/linux/mm.h:781 [inline]
ext4_xattr_inode_cache_find fs/ext4/xattr.c:1465 [inline]
ext4_xattr_inode_lookup_create fs/ext4/xattr.c:1508 [inline]
ext4_xattr_set_entry+0x1ce6/0x3780 fs/ext4/xattr.c:1649
ext4_xattr_ibody_set+0x78/0x2b0 fs/ext4/xattr.c:2224
ext4_xattr_set_handle+0x8f4/0x13e0 fs/ext4/xattr.c:2380
ext4_xattr_set+0x13a/0x340 fs/ext4/xattr.c:2493
This should be impossible since transaction start sets PF_MEMALLOC_NOFS.
Add some assertions to the code to catch if something isn't working as
expected early.
Link: https://lore.kernel.org/linux-ext4/000000000000563a0205bafb7970@google.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210222171626.21884-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5ca85707 upstream.
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8d ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b410ed2a85 ]
The only requirement of an auxtrace queue is that the buffers are in
time order. That is achieved by making separate queues for separate
perf buffer or AUX area buffer mmaps.
That generally means a separate queue per cpu for per-cpu contexts, and
a separate queue per thread for per-task contexts.
When buffers are added to a queue, perf checks that the buffer cpu and
thread id (tid) match the queue cpu and thread id.
However, generally, that need not be true, and perf will queue buffers
correctly anyway, so the check is not needed.
In addition, the check gets erroneously hit when using sample mode to
trace multiple threads.
Consequently, fix that case by removing the check.
Fixes: e502789302 ("perf auxtrace: Add helpers for queuing AUX area tracing data")
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20210308151143.18338-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb50aaf960 ]
The decrementation of acpi_device_bus_id->instance_no
in acpi_device_del() is incorrect, because it may cause
a duplicate instance number to be allocated next time
a device with the same acpi_device_bus_id is added.
Replace above mentioned approach by using IDA framework.
While at it, define the instance range to be [0, 4096).
Fixes: e49bd2dd5a ("ACPI: use PNPID:instance_no as bus_id of ACPI device")
Fixes: ca9dc8d42b ("ACPI / scan: Fix acpi_bus_id_list bookkeeping")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1013ff7a5 ]
The upfront allocation of new_bus_id is done to avoid allocating
memory under acpi_device_lock, but it doesn't really help,
because (1) it leads to many unnecessary memory allocations for
_ADR devices, (2) kstrdup_const() is run under that lock anyway and
(3) it complicates the code.
Rearrange acpi_device_add() to allocate memory for a new struct
acpi_device_bus_id instance only when necessary, eliminate a redundant
local variable from it and reduce the number of labels in there.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3408be145a ]
Not setting the ipv6 bit while destroying ipv6 listening servers may
result in potential fatal adapter errors due to lookup engine memory hash
errors. Therefore always set ipv6 field while destroying ipv6 listening
servers.
Fixes: 830662f6f0 ("RDMA/cxgb4: Add support for active and passive open connection with IPv6 address")
Link: https://lore.kernel.org/r/20210324190453.8171-1-bharat@chelsio.com
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 141f8202cf ]
The ppos points to a position in the old kernel memory (and in case of
arm64 in the crash kernel since elfcorehdr is passed as a segment). The
function should update the ppos by the amount that was read. This bug is
not exposed by accident, but other platforms update this value properly.
So, fix it in ARM64 version of elfcorehdr_read() as well.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Fixes: e62aaeac42 ("arm64: kdump: provide /proc/vmcore file")
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Link: https://lore.kernel.org/r/20210319205054.743368-1-pasha.tatashin@soleen.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 014dfa26ce ]
MTU cannot be changed on dwmac-sun8i. (ip link set eth0 mtu xxx returning EINVAL)
This is due to tx_fifo_size being 0, since this value is used to compute valid
MTU range.
Like dwmac-sunxi (with commit 806fd188ce ("net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes"))
dwmac-sun8i need to have tx and rx fifo sizes set.
I have used values from datasheets.
After this patch, setting a non-default MTU (like 1000) value works and network is still useable.
Tested-on: sun8i-h3-orangepi-pc
Tested-on: sun8i-r40-bananapi-m2-ultra
Tested-on: sun50i-a64-bananapi-m64
Tested-on: sun50i-h5-nanopi-neo-plus2
Tested-on: sun50i-h6-pine-h64
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c79a707072 ]
Set the disconnected flag before releasing the data interface in case
netdev registration fails to avoid having the disconnect callback try to
deregister the never registered netdev (and trigger a WARN_ON()).
Fixes: 87cf65601e ("USB host CDC Phonet network interface driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1944015fe9 ]
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d333 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e72 ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e399f3ba ]
Message loss from RX FIFO 0 is already handled in
m_can_handle_lost_msg(), with netdev output included.
Removing this warning also improves driver performance under heavy
load, where m_can_do_rx_poll() may be called many times before this
interrupt is cleared, causing this message to be output many
times (thanks Mariusz Madej for this report).
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/r/20210303103151.3760532-1-torin@maxiluxsystems.com
Reported-by: Mariusz Madej <mariusz.madej@xtrack.com>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db74623a38 ]
In qlcnic_83xx_get_minidump_template, fw_dump->tmpl_hdr was freed by
vfree(). But unfortunately, it is used when extended is true.
Fixes: 7061b2bdd6 ("qlogic: Deletion of unnecessary checks before two function calls")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b52912b829 ]
There is one e1e_wphy() call in e1000_set_d0_lplu_state_82571
that we have caught its return value but lack further handling.
Check and terminate the execution flow just like other e1e_wphy()
in this function.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f857f032 ]
A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b7 ("igb: reinit_locked() should be called
with rtnl_lock").
Added rtnl_lock() and rtnl_unlock() to avoid this.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47142ed6c3 ]
Similar to commit 92696286f3 ("net:
bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to
qualify the phydev->dev_flags based on whether the port is connected to
an internal or external PHY otherwise we risk having a flags collision
with a completely different interpretation depending on the driver.
Fixes: aa9aef77c7 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d7275b3e8 ]
The main purpose of l3 IRQs is to catch OCP bus access errors and identify
corresponding code places by showing call stack, so it's important to
handle L3 interconnect errors as fast as possible. On RT these IRQs will
became threaded and will be scheduled much more late from the moment actual
error occurred so showing completely useless information.
Hence, mark l3 IRQs as IRQF_NO_THREAD so they will not be forced threaded
on RT or if force_irqthreads = true.
Fixes: 0ee7261c92 ("drivers: bus: Move the OMAP interconnect driver to drivers/bus/")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4edbe1d7bc upstream.
If there are not any dm devices, we need to zero the "dev" argument in
the first structure dm_name_list. However, this can cause out of
bounds write, because the "needed" variable is zero and len may be
less than eight.
Fix this bug by reporting DM_BUFFER_FULL_FLAG if the result buffer is
too small to hold the "nl->dev" value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 221c3a09dd upstream.
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb1 ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba8da03fa7 upstream.
Crypto engine (CAAM) on LS1012A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 85b85c5695 ("arm64: dts: ls1012a: add crypto node")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ceb1ace4a ]
In https://bugs.gentoo.org/769614 Dmitry noticed that
`ptrace(PTRACE_GET_SYSCALL_INFO)` does not work for syscalls called via
glibc's syscall() wrapper.
ia64 has two ways to call syscalls from userspace: via `break` and via
`eps` instructions.
The difference is in stack layout:
1. `eps` creates simple stack frame: no locals, in{0..7} == out{0..8}
2. `break` uses userspace stack frame: may be locals (glibc provides
one), in{0..7} == out{0..8}.
Both work fine in syscall handling cde itself.
But `ptrace(PTRACE_GET_SYSCALL_INFO)` uses unwind mechanism to
re-extract syscall arguments but it does not account for locals.
The change always skips locals registers. It should not change `eps`
path as kernel's handler already enforces locals=0 and fixes `break`.
Tested on v5.10 on rx3600 machine (ia64 9040 CPU).
Link: https://lkml.kernel.org/r/20210221002554.333076-1-slyfox@gentoo.org
Link: https://bugs.gentoo.org/769614
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f8be1f53b ]
The NFSv4 protocol doesn't have any notion of reomoving an attribute, so
removexattr(path,"system.nfs4_acl") doesn't make sense.
There's no documented return value. Arguably it could be EOPNOTSUPP but
I'm a little worried an application might take that to mean that we
don't support ACLs or xattrs. How about EINVAL?
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5b0e0677b ]
Jakub reported that:
static struct net_device *rtl8139_init_board(struct pci_dev *pdev)
{
...
u64_stats_init(&tp->rx_stats.syncp);
u64_stats_init(&tp->tx_stats.syncp);
...
}
results in lockdep getting confused between the RX and TX stats lock.
This is because u64_stats_init() is an inline calling seqcount_init(),
which is a macro using a static variable to generate a lockdep class.
By wrapping that in an inline, we negate the effect of the macro and
fold the static key variable, hence the confusion.
Fix by also making u64_stats_init() a macro for the case where it
matters, leaving the other case an inline for argument validation
etc.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Debugged-by: "Ahmed S. Darwish" <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: "Erhard F." <erhard_f@mailbox.org>
Link: https://lkml.kernel.org/r/YEXicy6+9MksdLZh@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5e8b80d35 ]
is_no_fault_exception() has two bugs which were discovered via random
opcode testing with stress-ng. Both are caused by improper filtering
of opcodes.
The first bug can be triggered by a floating point store with a no-fault
ASI, for instance "sta %f0, [%g0] #ASI_PNF", opcode C1A01040.
The code first tests op3[5] (0x1000000), which denotes a floating
point instruction, and then tests op3[2] (0x200000), which denotes a
store instruction. But these bits are not mutually exclusive, and the
above mentioned opcode has both bits set. The intent is to filter out
stores, so the test for stores must be done first in order to have
any effect.
The second bug can be triggered by a floating point load with one of
the invalid ASI values 0x8e or 0x8f, which pass this check in
is_no_fault_exception():
if ((asi & 0xf2) == ASI_PNF)
An example instruction is "ldqa [%l7 + %o7] #ASI 0x8f, %f38",
opcode CF95D1EF. Asi values greater than 0x8b (ASI_SNFL) are fatal
in handle_ldf_stq(), and is_no_fault_exception() must not allow these
invalid asi values to make it that far.
In both of these cases, handle_ldf_stq() reacts by calling
sun4v_data_access_exception() or spitfire_data_access_exception(),
which call is_no_fault_exception() and results in an infinite
recursion.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4416e98594 ]
this one is similar to the phy_data allocation fix in uPD98402, the
driver allocate the idt77105_priv and store to dev_data but later
dereference using dev->dev_data, which will cause null-ptr-dereference.
fix this issue by changing dev_data to phy_data so that PRIV(dev) can
work correctly.
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3153724fc0 ]
dev->dev_data is set in zatm.c, calling zatm_start() will overwrite this
dev->dev_data in uPD98402_start() and a subsequent PRIV(dev)->lock
(i.e dev->phy_data->lock) will result in a null-ptr-dereference.
I believe this is a typo and what it actually want to do is to allocate
phy_data instead of dev_data.
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62765d3955 ]
When priv->rx_skbuff or priv->tx_skbuff is NULL, no error return code of
uhdlc_init() is assigned.
To fix this bug, ret is assigned with -ENOMEM in these cases.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 143c253f42 ]
When hns_assemble_skb() returns NULL to skb, no error return code of
hns_nic_clear_all_rx_fetch() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad3dbe35c8 ]
CREATE requests return a post_op_fh3, rather than nfs_fh3. The
post_op_fh3 includes an extra word to indicate 'handle_follows'.
Without that additional word, create fails when full 64-byte
filehandles are in use.
Add NFS3_post_op_fh_sz, and correct the size calculation for
NFS3_createres_sz.
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155b23e6e5 ]
RXMAC_BC_FRM_CNT_COUNT added to mp->rx_bcasts twice in a row
in niu_xmac_interrupt(). Remove the second addition.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38c26ff304 ]
When bdx_read_mac() fails, no error return code of bdx_probe()
is assigned.
To fix this bug, err is assigned with -EFAULT as error return code.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b5dc1a94d ]
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eead089311 ]
lkp reported a build error in fsp2.o:
CC arch/powerpc/platforms/44x/fsp2.o
{standard input}:577: Error: unsupported relocation against base
Which comes from:
pr_err("GESR0: 0x%08x\n", mfdcr(base + PLB4OPB_GESR0));
Where our mfdcr() macro is stringifying "base + PLB4OPB_GESR0", and
passing that to the assembler, which obviously doesn't work.
The mfdcr() macro already checks that the argument is constant using
__builtin_constant_p(), and if not calls the out-of-line version of
mfdcr(). But in this case GCC is smart enough to notice that "base +
PLB4OPB_GESR0" will be constant, even though it's not something we can
immediately stringify into a register number.
Segher pointed out that passing the register number to the inline asm
as a constant would be better, and in fact it fixes the build error,
presumably because it gives GCC a chance to resolve the value.
While we're at it, change mtdcr() similarly.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210218123058.748882-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4d7234ae ]
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 81e2073c17 upstream.
With interrupt force threading all device interrupt handlers are invoked
from kernel threads. Contrary to hard interrupt context the invocation only
disables bottom halfs, but not interrupts. This was an oversight back then
because any code like this will have an issue:
thread(irq_A)
irq_handler(A)
spin_lock(&foo->lock);
interrupt(irq_B)
irq_handler(B)
spin_lock(&foo->lock);
This has been triggered with networking (NAPI vs. hrtimers) and console
drivers where printk() happens from an interrupt which interrupted the
force threaded handler.
Now people noticed and started to change the spin_lock() in the handler to
spin_lock_irqsave() which affects performance or add IRQF_NOTHREAD to the
interrupt request which in turn breaks RT.
Fix the root cause and not the symptom and disable interrupts before
invoking the force threaded handler which preserves the regular semantics
and the usefulness of the interrupt force threading as a general debugging
tool.
For not RT this is not changing much, except that during the execution of
the threaded handler interrupts are delayed until the handler
returns. Vs. scheduling and softirq processing there is no difference.
For RT kernels there is no issue.
Fixes: 8d32a307e4 ("genirq: Provide forced interrupt threading")
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210317143859.513307808@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b22489911 upstream.
Syzbot report a warning that ext4 may create an empty ea_inode if set
an empty extent attribute to a file on the file system which is no free
blocks left.
WARNING: CPU: 6 PID: 10667 at fs/ext4/xattr.c:1640 ext4_xattr_set_entry+0x10f8/0x1114 fs/ext4/xattr.c:1640
...
Call trace:
ext4_xattr_set_entry+0x10f8/0x1114 fs/ext4/xattr.c:1640
ext4_xattr_block_set+0x1d0/0x1b1c fs/ext4/xattr.c:1942
ext4_xattr_set_handle+0x8a0/0xf1c fs/ext4/xattr.c:2390
ext4_xattr_set+0x120/0x1f0 fs/ext4/xattr.c:2491
ext4_xattr_trusted_set+0x48/0x5c fs/ext4/xattr_trusted.c:37
__vfs_setxattr+0x208/0x23c fs/xattr.c:177
...
Now, ext4 try to store extent attribute into an external inode if
ext4_xattr_block_set() return -ENOSPC, but for the case of store an
empty extent attribute, store the extent entry into the extent
attribute block is enough. A simple reproduce below.
fallocate test.img -l 1M
mkfs.ext4 -F -b 2048 -O ea_inode test.img
mount test.img /mnt
dd if=/dev/zero of=/mnt/foo bs=2048 count=500
setfattr -n "user.test" /mnt/foo
Reported-by: syzbot+98b881fdd8ebf45ab4ae@syzkaller.appspotmail.com
Fixes: 9c6e7853c5 ("ext4: reserve space for xattr entries/names")
Cc: stable@kernel.org
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210305120508.298465-1-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7ff91fd03 upstream.
If we failed to add new entry on rename whiteout, we cannot reset the
old->de entry directly, because the old->de could have moved from under
us during make indexed dir. So find the old entry again before reset is
needed, otherwise it may corrupt the filesystem as below.
/dev/sda: Entry '00000001' in ??? (12) has deleted/unused inode 15. CLEARED.
/dev/sda: Unattached inode 75
/dev/sda: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Fixes: 6b4b8e6b4a ("ext4: fix bug for rename with RENAME_WHITEOUT")
Cc: stable@vger.kernel.org
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Link: https://lore.kernel.org/r/20210303131703.330415-1-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c150ba2fb upstream.
The comment in get_nr_restart_syscall() says:
* The problem is that we can get here when ptrace pokes
* syscall-like values into regs even if we're not in a syscall
* at all.
Yes, but if not in a syscall then the
status & (TS_COMPAT|TS_I386_REGS_POKED)
check below can't really help:
- TS_COMPAT can't be set
- TS_I386_REGS_POKED is only set if regs->orig_ax was changed by
32bit debugger; and even in this case get_nr_restart_syscall()
is only correct if the tracee is 32bit too.
Suppose that a 64bit debugger plays with a 32bit tracee and
* Tracee calls sleep(2) // TS_COMPAT is set
* User interrupts the tracee by CTRL-C after 1 sec and does
"(gdb) call func()"
* gdb saves the regs by PTRACE_GETREGS
* does PTRACE_SETREGS to set %rip='func' and %orig_rax=-1
* PTRACE_CONT // TS_COMPAT is cleared
* func() hits int3.
* Debugger catches SIGTRAP.
* Restore original regs by PTRACE_SETREGS.
* PTRACE_CONT
get_nr_restart_syscall() wrongly returns __NR_restart_syscall==219, the
tracee calls ia32_sys_call_table[219] == sys_madvise.
Add the sticky TS_COMPAT_RESTART flag which survives after return to user
mode. It's going to be removed in the next step again by storing the
information in the restart block. As a further cleanup it might be possible
to remove also TS_I386_REGS_POKED with that.
Test-case:
$ cvs -d :pserver:anoncvs:anoncvs@sourceware.org:/cvs/systemtap co ptrace-tests
$ gcc -o erestartsys-trap-debuggee ptrace-tests/tests/erestartsys-trap-debuggee.c --m32
$ gcc -o erestartsys-trap-debugger ptrace-tests/tests/erestartsys-trap-debugger.c -lutil
$ ./erestartsys-trap-debugger
Unexpected: retval 1, errno 22
erestartsys-trap-debugger: ptrace-tests/tests/erestartsys-trap-debugger.c:421
Fixes: 609c19a385 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174709.GA17895@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c1b6d74c upstream.
Move TS_COMPAT back to asm/thread_info.h, close to TS_I386_REGS_POKED.
It was moved to asm/processor.h by b9d989c721 ("x86/asm: Move the
thread_info::status field to thread_struct"), then later 37a8f7c383
("x86/asm: Move 'status' from thread_struct to thread_info") moved the
'status' field back but TS_COMPAT was forgotten.
Preparatory patch to fix the COMPAT case for get_nr_restart_syscall()
Fixes: 609c19a385 ("x86/ptrace: Stop setting TS_COMPAT in ptrace code")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210201174649.GA17880@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a501b048a9 upstream.
Vitaly ran into an issue with hotplugging CPU0 on an Amazon instance where
the matrix allocator claimed to be out of vectors. He analyzed it down to
the point that IRQ2, the PIC cascade interrupt, which is supposed to be not
ever routed to the IO/APIC ended up having an interrupt vector assigned
which got moved during unplug of CPU0.
The underlying issue is that IRQ2 for various reasons (see commit
af174783b9 ("x86: I/O APIC: Never configure IRQ2" for details) is treated
as a reserved system vector by the vector core code and is not accounted as
a regular vector. The Amazon BIOS has an routing entry of pin2 to IRQ2
which causes the IO/APIC setup to claim that interrupt which is granted by
the vector domain because there is no sanity check. As a consequence the
allocation counter of CPU0 underflows which causes a subsequent unplug to
fail with:
[ ... ] CPU 0 has 4294967295 vectors, 589 available. Cannot disable CPU
There is another sanity check missing in the matrix allocator, but the
underlying root cause is that the IO/APIC code lost the IRQ2 ignore logic
during the conversion to irqdomains.
For almost 6 years nobody complained about this wreckage, which might
indicate that this requirement could be lifted, but for any system which
actually has a PIC IRQ2 is unusable by design so any routing entry has no
effect and the interrupt cannot be connected to a device anyway.
Due to that and due to history biased paranoia reasons restore the IRQ2
ignore logic and treat it as non existent despite a routing entry claiming
otherwise.
Fixes: d32932d02e ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210318192819.636943062@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d88d05a9e0 upstream.
A repeatable crash can be triggered by the perf_fuzzer on some Haswell
system.
https://lore.kernel.org/lkml/7170d3b-c17f-1ded-52aa-cc6d9ae999f4@maine.edu/
For some old CPUs (HSW and earlier), the PEBS status in a PEBS record
may be mistakenly set to 0. To minimize the impact of the defect, the
commit was introduced to try to avoid dropping the PEBS record for some
cases. It adds a check in the intel_pmu_drain_pebs_nhm(), and updates
the local pebs_status accordingly. However, it doesn't correct the PEBS
status in the PEBS record, which may trigger the crash, especially for
the large PEBS.
It's possible that all the PEBS records in a large PEBS have the PEBS
status 0. If so, the first get_next_pebs_record_by_bit() in the
__intel_pmu_pebs_event() returns NULL. The at = NULL. Since it's a large
PEBS, the 'count' parameter must > 1. The second
get_next_pebs_record_by_bit() will crash.
Besides the local pebs_status, correct the PEBS status in the PEBS
record as well.
Fixes: 01330d7288 ("perf/x86: Allow zero PEBS status with only single active event")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1615555298-140216-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7a0bb058 upstream.
Both add_slot_store() and remove_slot_store() try to fix up the
drc_name copied from the store buffer by placing a NUL terminator at
nbyte + 1 or in place of a '\n' if present. However, the static buffer
that we copy the drc_name data into is not zeroed and can contain
anything past the n-th byte.
This is problematic if a '\n' byte appears in that buffer after nbytes
and the string copied into the store buffer was not NUL terminated to
start with as the strchr() search for a '\n' byte will mark this
incorrectly as the end of the drc_name string resulting in a drc_name
string that contains garbage data after the n-th byte.
Additionally it will cause us to overwrite that '\n' byte on the stack
with NUL, potentially corrupting data on the stack.
The following debugging shows an example of the drmgr utility writing
"PHB 4543" to the add_slot sysfs attribute, but add_slot_store()
logging a corrupted string value.
drmgr: drmgr: -c phb -a -s PHB 4543 -d 1
add_slot_store: drc_name = PHB 4543°|<82>!, rc = -19
Fix this by using strscpy() instead of memcpy() to ensure the string
is NUL terminated when copied into the static drc_name buffer.
Further, since the string is now NUL terminated the code only needs to
change '\n' to '\0' when present.
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mpe: Reformat change log and add mention of possible stack corruption]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315214821.452959-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98f153a10d upstream.
When gadget is disconnected, running sequence is like this.
. composite_disconnect
. Call trace:
usb_string_copy+0xd0/0x128
gadget_config_name_configuration_store+0x4
gadget_config_name_attr_store+0x40/0x50
configfs_write_file+0x198/0x1f4
vfs_write+0x100/0x220
SyS_write+0x58/0xa8
. configfs_composite_unbind
. configfs_composite_bind
In configfs_composite_bind, it has
"cn->strings.s = cn->configuration;"
When usb_string_copy is invoked. it would
allocate memory, copy input string, release previous pointed memory space,
and use new allocated memory.
When gadget is connected, host sends down request to get information.
Call trace:
usb_gadget_get_string+0xec/0x168
lookup_string+0x64/0x98
composite_setup+0xa34/0x1ee8
If gadget is disconnected and connected quickly, in the failed case,
cn->configuration memory has been released by usb_string_copy kfree but
configfs_composite_bind hasn't been run in time to assign new allocated
"cn->configuration" pointer to "cn->strings.s".
When "strlen(s->s) of usb_gadget_get_string is being executed, the dangling
memory is accessed, "BUG: KASAN: use-after-free" error occurs.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/1615444961-13376-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 546aa0e4ea upstream.
Matthias reports that the Amazon Kindle automatically removes its
emulated media if it doesn't receive another SCSI command within about
one second after a SYNCHRONIZE CACHE. It does so even when the host
has sent a PREVENT MEDIUM REMOVAL command. The reason for this
behavior isn't clear, although it's not hard to make some guesses.
At any rate, the results can be unexpected for anyone who tries to
access the Kindle in an unusual fashion, and in theory they can lead
to data loss (for example, if one file is closed and synchronized
while other files are still in the middle of being written).
To avoid such problems, this patch creates a new usb-storage quirks
flag telling the driver always to issue a REQUEST SENSE following a
SYNCHRONIZE CACHE command, and adds an unusual_devs entry for the
Kindle with the flag set. This is sufficient to prevent the Kindle
from doing its automatic unload, without interfering with proper
operation.
Another possible way to deal with this would be to increase the
frequency of TEST UNIT READY polling that the kernel normally carries
out for removable-media storage devices. However that would increase
the overall load on the system and it is not as reliable, because the
user can override the polling interval. Changing the driver's
behavior is safer and has minimal overhead.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210317190654.GA497856@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c4c6df5fc8 ]
We only setup io queues for nvme controllers, and it makes absolutely no
sense to allow a controller (re)connect without any I/O queues. If we
happen to fail setting the queue count for any reason, we should not allow
this to be a successful reconnect as I/O has no chance in going through.
Instead just fail and schedule another reconnect.
Reported-by: Chao Leng <lengchao@huawei.com>
Fixes: 7110230719 ("nvme-rdma: add a NVMe over Fabrics RDMA host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 093b036aa9 upstream.
syzbot found WARNING in __alloc_pages_nodemask()[1] when order >= MAX_ORDER.
It was caused by a huge length value passed from userspace to qrtr_tun_write_iter(),
which tries to allocate skb. Since the value comes from the untrusted source
there is no need to raise a warning in __alloc_pages_nodemask().
[1] WARNING in __alloc_pages_nodemask+0x5f8/0x730 mm/page_alloc.c:5014
Call Trace:
__alloc_pages include/linux/gfp.h:511 [inline]
__alloc_pages_node include/linux/gfp.h:524 [inline]
alloc_pages_node include/linux/gfp.h:538 [inline]
kmalloc_large_node+0x60/0x110 mm/slub.c:3999
__kmalloc_node_track_caller+0x319/0x3f0 mm/slub.c:4496
__kmalloc_reserve net/core/skbuff.c:150 [inline]
__alloc_skb+0x4e4/0x5a0 net/core/skbuff.c:210
__netdev_alloc_skb+0x70/0x400 net/core/skbuff.c:446
netdev_alloc_skb include/linux/skbuff.h:2832 [inline]
qrtr_endpoint_post+0x84/0x11b0 net/qrtr/qrtr.c:442
qrtr_tun_write_iter+0x11f/0x1a0 net/qrtr/tun.c:98
call_write_iter include/linux/fs.h:1901 [inline]
new_sync_write+0x426/0x650 fs/read_write.c:518
vfs_write+0x791/0xa30 fs/read_write.c:605
ksys_write+0x12d/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported-by: syzbot+80dccaee7c6630fa9dcf@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1442d6349 upstream.
If an auth module's accept op returns SVC_CLOSE, svc_process_common()
enters a call path that does not call svc_authorise() before leaving the
function, and thus leaks a reference on the auth module's refcount. Hence,
make sure calls to svc_authenticate() and svc_authorise() are paired for
all call paths, to make sure rpc auth modules can be unloaded.
Signed-off-by: Daniel Kobras <kobras@puzzle-itc.de>
Fixes: 4d712ef1db ("svcauth_gss: Close connection when dropping an incoming message")
Link: https://lore.kernel.org/linux-nfs/3F1B347F-B809-478F-A1E9-0BE98E22B0F0@oracle.com/T/#t
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6820bf7786 upstream.
This brings it in line with the regular tcp backchannel, which also has
all those timeouts disabled.
Prevents the backchannel from timing out, getting some async operations
like server side copying getting stuck indefinitely on the client side.
Signed-off-by: Timo Rothenpieler <timo@rothenpieler.org>
Fixes: 5d252f90a8 ("svcrdma: Add class for RDMA backwards direction transport")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7de87ff9d upstream.
[ This problem is in mainline, but only rt has the chops to be
able to detect it. ]
Lockdep reports a circular lock dependency between serv->sv_lock and
softirq_ctl.lock on system shutdown, when using a kernel built with
CONFIG_PREEMPT_RT=y, and a nfs mount exists.
This is due to the definition of spin_lock_bh on rt:
local_bh_disable();
rt_spin_lock(lock);
which forces a softirq_ctl.lock -> serv->sv_lock dependency. This is
not a problem as long as _every_ lock of serv->sv_lock is a:
spin_lock_bh(&serv->sv_lock);
but there is one of the form:
spin_lock(&serv->sv_lock);
This is what is causing the circular dependency splat. The spin_lock()
grabs the lock without first grabbing softirq_ctl.lock via local_bh_disable.
If later on in the critical region, someone does a local_bh_disable, we
get a serv->sv_lock -> softirq_ctrl.lock dependency established. Deadlock.
Fix is to make serv->sv_lock be locked with spin_lock_bh everywhere, no
exceptions.
[ OK ] Stopped target NFS client services.
Stopping Logout off all iSCSI sessions on shutdown...
Stopping NFS server and services...
[ 109.442380]
[ 109.442385] ======================================================
[ 109.442386] WARNING: possible circular locking dependency detected
[ 109.442387] 5.10.16-rt30 #1 Not tainted
[ 109.442389] ------------------------------------------------------
[ 109.442390] nfsd/1032 is trying to acquire lock:
[ 109.442392] ffff994237617f60 ((softirq_ctrl.lock).lock){+.+.}-{2:2}, at: __local_bh_disable_ip+0xd9/0x270
[ 109.442405]
[ 109.442405] but task is already holding lock:
[ 109.442406] ffff994245cb00b0 (&serv->sv_lock){+.+.}-{0:0}, at: svc_close_list+0x1f/0x90
[ 109.442415]
[ 109.442415] which lock already depends on the new lock.
[ 109.442415]
[ 109.442416]
[ 109.442416] the existing dependency chain (in reverse order) is:
[ 109.442417]
[ 109.442417] -> #1 (&serv->sv_lock){+.+.}-{0:0}:
[ 109.442421] rt_spin_lock+0x2b/0xc0
[ 109.442428] svc_add_new_perm_xprt+0x42/0xa0
[ 109.442430] svc_addsock+0x135/0x220
[ 109.442434] write_ports+0x4b3/0x620
[ 109.442438] nfsctl_transaction_write+0x45/0x80
[ 109.442440] vfs_write+0xff/0x420
[ 109.442444] ksys_write+0x4f/0xc0
[ 109.442446] do_syscall_64+0x33/0x40
[ 109.442450] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 109.442454]
[ 109.442454] -> #0 ((softirq_ctrl.lock).lock){+.+.}-{2:2}:
[ 109.442457] __lock_acquire+0x1264/0x20b0
[ 109.442463] lock_acquire+0xc2/0x400
[ 109.442466] rt_spin_lock+0x2b/0xc0
[ 109.442469] __local_bh_disable_ip+0xd9/0x270
[ 109.442471] svc_xprt_do_enqueue+0xc0/0x4d0
[ 109.442474] svc_close_list+0x60/0x90
[ 109.442476] svc_close_net+0x49/0x1a0
[ 109.442478] svc_shutdown_net+0x12/0x40
[ 109.442480] nfsd_destroy+0xc5/0x180
[ 109.442482] nfsd+0x1bc/0x270
[ 109.442483] kthread+0x194/0x1b0
[ 109.442487] ret_from_fork+0x22/0x30
[ 109.442492]
[ 109.442492] other info that might help us debug this:
[ 109.442492]
[ 109.442493] Possible unsafe locking scenario:
[ 109.442493]
[ 109.442493] CPU0 CPU1
[ 109.442494] ---- ----
[ 109.442495] lock(&serv->sv_lock);
[ 109.442496] lock((softirq_ctrl.lock).lock);
[ 109.442498] lock(&serv->sv_lock);
[ 109.442499] lock((softirq_ctrl.lock).lock);
[ 109.442501]
[ 109.442501] *** DEADLOCK ***
[ 109.442501]
[ 109.442501] 3 locks held by nfsd/1032:
[ 109.442503] #0: ffffffff93b49258 (nfsd_mutex){+.+.}-{3:3}, at: nfsd+0x19a/0x270
[ 109.442508] #1: ffff994245cb00b0 (&serv->sv_lock){+.+.}-{0:0}, at: svc_close_list+0x1f/0x90
[ 109.442512] #2: ffffffff93a81b20 (rcu_read_lock){....}-{1:2}, at: rt_spin_lock+0x5/0xc0
[ 109.442518]
[ 109.442518] stack backtrace:
[ 109.442519] CPU: 0 PID: 1032 Comm: nfsd Not tainted 5.10.16-rt30 #1
[ 109.442522] Hardware name: Supermicro X9DRL-3F/iF/X9DRL-3F/iF, BIOS 3.2 09/22/2015
[ 109.442524] Call Trace:
[ 109.442527] dump_stack+0x77/0x97
[ 109.442533] check_noncircular+0xdc/0xf0
[ 109.442546] __lock_acquire+0x1264/0x20b0
[ 109.442553] lock_acquire+0xc2/0x400
[ 109.442564] rt_spin_lock+0x2b/0xc0
[ 109.442570] __local_bh_disable_ip+0xd9/0x270
[ 109.442573] svc_xprt_do_enqueue+0xc0/0x4d0
[ 109.442577] svc_close_list+0x60/0x90
[ 109.442581] svc_close_net+0x49/0x1a0
[ 109.442585] svc_shutdown_net+0x12/0x40
[ 109.442588] nfsd_destroy+0xc5/0x180
[ 109.442590] nfsd+0x1bc/0x270
[ 109.442595] kthread+0x194/0x1b0
[ 109.442600] ret_from_fork+0x22/0x30
[ 109.518225] nfsd: last server has exited, flushing export cache
[ OK ] Stopped NFSv4 ID-name mapping service.
[ OK ] Stopped GSSAPI Proxy Daemon.
[ OK ] Stopped NFS Mount Daemon.
[ OK ] Stopped NFS status monitor for NFSv2/3 locking..
Fixes: 719f8bcc88 ("svcrpc: fix xpt_list traversal locking on shutdown")
Signed-off-by: Joe Korty <joe.korty@concurrent-rt.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d218a8a300 upstream.
From the base spec, Figure 78:
"Controller Configuration, these fields are defined as parameters to
configure an "I/O Controller (IOC)" and not to configure a "Discovery
Controller (DC).
...
If the controller does not support I/O queues, then this field shall
be read-only with a value of 0h
Just perform this check for I/O controllers.
Fixes: a07b4970f4 ("nvmet: add a generic NVMe target")
Reported-by: Belanger, Martin <Martin.Belanger@dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbcc7d57bf upstream.
While resolving backreferences, as part of a logical ino ioctl call or
fiemap, we can end up hitting a BUG_ON() when replaying tree mod log
operations of a root, triggering a stack trace like the following:
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.c:1210!
invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 19054 Comm: crawl_335 Tainted: G W 5.11.0-2d11c0084b02-misc-next+ #89
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:__tree_mod_log_rewind+0x3b1/0x3c0
Code: 05 48 8d 74 10 (...)
RSP: 0018:ffffc90001eb70b8 EFLAGS: 00010297
RAX: 0000000000000000 RBX: ffff88812344e400 RCX: ffffffffb28933b6
RDX: 0000000000000007 RSI: dffffc0000000000 RDI: ffff88812344e42c
RBP: ffffc90001eb7108 R08: 1ffff11020b60a20 R09: ffffed1020b60a20
R10: ffff888105b050f9 R11: ffffed1020b60a1f R12: 00000000000000ee
R13: ffff8880195520c0 R14: ffff8881bc958500 R15: ffff88812344e42c
FS: 00007fd1955e8700(0000) GS:ffff8881f5600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007efdb7928718 CR3: 000000010103a006 CR4: 0000000000170ee0
Call Trace:
btrfs_search_old_slot+0x265/0x10d0
? lock_acquired+0xbb/0x600
? btrfs_search_slot+0x1090/0x1090
? free_extent_buffer.part.61+0xd7/0x140
? free_extent_buffer+0x13/0x20
resolve_indirect_refs+0x3e9/0xfc0
? lock_downgrade+0x3d0/0x3d0
? __kasan_check_read+0x11/0x20
? add_prelim_ref.part.11+0x150/0x150
? lock_downgrade+0x3d0/0x3d0
? __kasan_check_read+0x11/0x20
? lock_acquired+0xbb/0x600
? __kasan_check_write+0x14/0x20
? do_raw_spin_unlock+0xa8/0x140
? rb_insert_color+0x30/0x360
? prelim_ref_insert+0x12d/0x430
find_parent_nodes+0x5c3/0x1830
? resolve_indirect_refs+0xfc0/0xfc0
? lock_release+0xc8/0x620
? fs_reclaim_acquire+0x67/0xf0
? lock_acquire+0xc7/0x510
? lock_downgrade+0x3d0/0x3d0
? lockdep_hardirqs_on_prepare+0x160/0x210
? lock_release+0xc8/0x620
? fs_reclaim_acquire+0x67/0xf0
? lock_acquire+0xc7/0x510
? poison_range+0x38/0x40
? unpoison_range+0x14/0x40
? trace_hardirqs_on+0x55/0x120
btrfs_find_all_roots_safe+0x142/0x1e0
? find_parent_nodes+0x1830/0x1830
? btrfs_inode_flags_to_xflags+0x50/0x50
iterate_extent_inodes+0x20e/0x580
? tree_backref_for_extent+0x230/0x230
? lock_downgrade+0x3d0/0x3d0
? read_extent_buffer+0xdd/0x110
? lock_downgrade+0x3d0/0x3d0
? __kasan_check_read+0x11/0x20
? lock_acquired+0xbb/0x600
? __kasan_check_write+0x14/0x20
? _raw_spin_unlock+0x22/0x30
? __kasan_check_write+0x14/0x20
iterate_inodes_from_logical+0x129/0x170
? iterate_inodes_from_logical+0x129/0x170
? btrfs_inode_flags_to_xflags+0x50/0x50
? iterate_extent_inodes+0x580/0x580
? __vmalloc_node+0x92/0xb0
? init_data_container+0x34/0xb0
? init_data_container+0x34/0xb0
? kvmalloc_node+0x60/0x80
btrfs_ioctl_logical_to_ino+0x158/0x230
btrfs_ioctl+0x205e/0x4040
? __might_sleep+0x71/0xe0
? btrfs_ioctl_get_supported_features+0x30/0x30
? getrusage+0x4b6/0x9c0
? __kasan_check_read+0x11/0x20
? lock_release+0xc8/0x620
? __might_fault+0x64/0xd0
? lock_acquire+0xc7/0x510
? lock_downgrade+0x3d0/0x3d0
? lockdep_hardirqs_on_prepare+0x210/0x210
? lockdep_hardirqs_on_prepare+0x210/0x210
? __kasan_check_read+0x11/0x20
? do_vfs_ioctl+0xfc/0x9d0
? ioctl_file_clone+0xe0/0xe0
? lock_downgrade+0x3d0/0x3d0
? lockdep_hardirqs_on_prepare+0x210/0x210
? __kasan_check_read+0x11/0x20
? lock_release+0xc8/0x620
? __task_pid_nr_ns+0xd3/0x250
? lock_acquire+0xc7/0x510
? __fget_files+0x160/0x230
? __fget_light+0xf2/0x110
__x64_sys_ioctl+0xc3/0x100
do_syscall_64+0x37/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fd1976e2427
Code: 00 00 90 48 8b 05 (...)
RSP: 002b:00007fd1955e5cf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fd1955e5f40 RCX: 00007fd1976e2427
RDX: 00007fd1955e5f48 RSI: 00000000c038943b RDI: 0000000000000004
RBP: 0000000001000000 R08: 0000000000000000 R09: 00007fd1955e6120
R10: 0000557835366b00 R11: 0000000000000246 R12: 0000000000000004
R13: 00007fd1955e5f48 R14: 00007fd1955e5f40 R15: 00007fd1955e5ef8
Modules linked in:
---[ end trace ec8931a1c36e57be ]---
(gdb) l *(__tree_mod_log_rewind+0x3b1)
0xffffffff81893521 is in __tree_mod_log_rewind (fs/btrfs/ctree.c:1210).
1205 * the modification. as we're going backwards, we do the
1206 * opposite of each operation here.
1207 */
1208 switch (tm->op) {
1209 case MOD_LOG_KEY_REMOVE_WHILE_FREEING:
1210 BUG_ON(tm->slot < n);
1211 fallthrough;
1212 case MOD_LOG_KEY_REMOVE_WHILE_MOVING:
1213 case MOD_LOG_KEY_REMOVE:
1214 btrfs_set_node_key(eb, &tm->key, tm->slot);
Here's what happens to hit that BUG_ON():
1) We have one tree mod log user (through fiemap or the logical ino ioctl),
with a sequence number of 1, so we have fs_info->tree_mod_seq == 1;
2) Another task is at ctree.c:balance_level() and we have eb X currently as
the root of the tree, and we promote its single child, eb Y, as the new
root.
Then, at ctree.c:balance_level(), we call:
tree_mod_log_insert_root(eb X, eb Y, 1);
3) At tree_mod_log_insert_root() we create tree mod log elements for each
slot of eb X, of operation type MOD_LOG_KEY_REMOVE_WHILE_FREEING each
with a ->logical pointing to ebX->start. These are placed in an array
named tm_list.
Lets assume there are N elements (N pointers in eb X);
4) Then, still at tree_mod_log_insert_root(), we create a tree mod log
element of operation type MOD_LOG_ROOT_REPLACE, ->logical set to
ebY->start, ->old_root.logical set to ebX->start, ->old_root.level set
to the level of eb X and ->generation set to the generation of eb X;
5) Then tree_mod_log_insert_root() calls tree_mod_log_free_eb() with
tm_list as argument. After that, tree_mod_log_free_eb() calls
__tree_mod_log_insert() for each member of tm_list in reverse order,
from highest slot in eb X, slot N - 1, to slot 0 of eb X;
6) __tree_mod_log_insert() sets the sequence number of each given tree mod
log operation - it increments fs_info->tree_mod_seq and sets
fs_info->tree_mod_seq as the sequence number of the given tree mod log
operation.
This means that for the tm_list created at tree_mod_log_insert_root(),
the element corresponding to slot 0 of eb X has the highest sequence
number (1 + N), and the element corresponding to the last slot has the
lowest sequence number (2);
7) Then, after inserting tm_list's elements into the tree mod log rbtree,
the MOD_LOG_ROOT_REPLACE element is inserted, which gets the highest
sequence number, which is N + 2;
8) Back to ctree.c:balance_level(), we free eb X by calling
btrfs_free_tree_block() on it. Because eb X was created in the current
transaction, has no other references and writeback did not happen for
it, we add it back to the free space cache/tree;
9) Later some other task T allocates the metadata extent from eb X, since
it is marked as free space in the space cache/tree, and uses it as a
node for some other btree;
10) The tree mod log user task calls btrfs_search_old_slot(), which calls
get_old_root(), and finally that calls __tree_mod_log_oldest_root()
with time_seq == 1 and eb_root == eb Y;
11) First iteration of the while loop finds the tree mod log element with
sequence number N + 2, for the logical address of eb Y and of type
MOD_LOG_ROOT_REPLACE;
12) Because the operation type is MOD_LOG_ROOT_REPLACE, we don't break out
of the loop, and set root_logical to point to tm->old_root.logical
which corresponds to the logical address of eb X;
13) On the next iteration of the while loop, the call to
tree_mod_log_search_oldest() returns the smallest tree mod log element
for the logical address of eb X, which has a sequence number of 2, an
operation type of MOD_LOG_KEY_REMOVE_WHILE_FREEING and corresponds to
the old slot N - 1 of eb X (eb X had N items in it before being freed);
14) We then break out of the while loop and return the tree mod log operation
of type MOD_LOG_ROOT_REPLACE (eb Y), and not the one for slot N - 1 of
eb X, to get_old_root();
15) At get_old_root(), we process the MOD_LOG_ROOT_REPLACE operation
and set "logical" to the logical address of eb X, which was the old
root. We then call tree_mod_log_search() passing it the logical
address of eb X and time_seq == 1;
16) Then before calling tree_mod_log_search(), task T adds a key to eb X,
which results in adding a tree mod log operation of type
MOD_LOG_KEY_ADD to the tree mod log - this is done at
ctree.c:insert_ptr() - but after adding the tree mod log operation
and before updating the number of items in eb X from 0 to 1...
17) The task at get_old_root() calls tree_mod_log_search() and gets the
tree mod log operation of type MOD_LOG_KEY_ADD just added by task T.
Then it enters the following if branch:
if (old_root && tm && tm->op != MOD_LOG_KEY_REMOVE_WHILE_FREEING) {
(...)
} (...)
Calls read_tree_block() for eb X, which gets a reference on eb X but
does not lock it - task T has it locked.
Then it clones eb X while it has nritems set to 0 in its header, before
task T sets nritems to 1 in eb X's header. From hereupon we use the
clone of eb X which no other task has access to;
18) Then we call __tree_mod_log_rewind(), passing it the MOD_LOG_KEY_ADD
mod log operation we just got from tree_mod_log_search() in the
previous step and the cloned version of eb X;
19) At __tree_mod_log_rewind(), we set the local variable "n" to the number
of items set in eb X's clone, which is 0. Then we enter the while loop,
and in its first iteration we process the MOD_LOG_KEY_ADD operation,
which just decrements "n" from 0 to (u32)-1, since "n" is declared with
a type of u32. At the end of this iteration we call rb_next() to find the
next tree mod log operation for eb X, that gives us the mod log operation
of type MOD_LOG_KEY_REMOVE_WHILE_FREEING, for slot 0, with a sequence
number of N + 1 (steps 3 to 6);
20) Then we go back to the top of the while loop and trigger the following
BUG_ON():
(...)
switch (tm->op) {
case MOD_LOG_KEY_REMOVE_WHILE_FREEING:
BUG_ON(tm->slot < n);
fallthrough;
(...)
Because "n" has a value of (u32)-1 (4294967295) and tm->slot is 0.
Fix this by taking a read lock on the extent buffer before cloning it at
ctree.c:get_old_root(). This should be done regardless of the extent
buffer having been freed and reused, as a concurrent task might be
modifying it (while holding a write lock on it).
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Link: https://lore.kernel.org/linux-btrfs/20210227155037.GN28049@hungrycats.org/
Fixes: 834328a849 ("Btrfs: tree mod log's old roots could still be part of the tree")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4541a8bb13 upstream.
Laura reported that the perf build failed in fedora when we got a glibc
that provides gettid(), which I reproduced using fedora rawhide with the
glibc-devel-2.29.9000-26.fc31.x86_64 package.
Add a feature check to avoid providing a gettid() helper in such
systems.
On a fedora rawhide system with this patch applied we now get:
[root@7a5f55352234 perf]# grep gettid /tmp/build/perf/FEATURE-DUMP
feature-gettid=1
[root@7a5f55352234 perf]# cat /tmp/build/perf/feature/test-gettid.make.output
[root@7a5f55352234 perf]# ldd /tmp/build/perf/feature/test-gettid.bin
linux-vdso.so.1 (0x00007ffc6b1f6000)
libc.so.6 => /lib64/libc.so.6 (0x00007f04e0a74000)
/lib64/ld-linux-x86-64.so.2 (0x00007f04e0c47000)
[root@7a5f55352234 perf]# nm /tmp/build/perf/feature/test-gettid.bin | grep -w gettid
U gettid@@GLIBC_2.30
[root@7a5f55352234 perf]#
While on a fedora:29 system:
[acme@quaco perf]$ grep gettid /tmp/build/perf/FEATURE-DUMP
feature-gettid=0
[acme@quaco perf]$ cat /tmp/build/perf/feature/test-gettid.make.output
test-gettid.c: In function ‘main’:
test-gettid.c:8:9: error: implicit declaration of function ‘gettid’; did you mean ‘getgid’? [-Werror=implicit-function-declaration]
return gettid();
^~~~~~
getgid
cc1: all warnings being treated as errors
[acme@quaco perf]$
Reported-by: Laura Abbott <labbott@redhat.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lkml.kernel.org/n/tip-yfy3ch53agmklwu9o7rlgf9c@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11c6cbe706 upstream.
A new 'perf bench epoll' will use this, and to disable it for older
systems, add a feature test for this API.
This is just a simple program that if successfully compiled, means that
the feature is present, at least at the library level, in a build that
sets the output directory to /tmp/build/perf (using O=/tmp/build/perf),
we end up with:
$ ls -la /tmp/build/perf/feature/test-eventfd*
-rwxrwxr-x. 1 acme acme 8176 Nov 21 15:58 /tmp/build/perf/feature/test-eventfd.bin
-rw-rw-r--. 1 acme acme 588 Nov 21 15:58 /tmp/build/perf/feature/test-eventfd.d
-rw-rw-r--. 1 acme acme 0 Nov 21 15:58 /tmp/build/perf/feature/test-eventfd.make.output
$ ldd /tmp/build/perf/feature/test-eventfd.bin
linux-vdso.so.1 (0x00007fff3bf3f000)
libc.so.6 => /lib64/libc.so.6 (0x00007fa984061000)
/lib64/ld-linux-x86-64.so.2 (0x00007fa984417000)
$ grep eventfd -A 2 -B 2 /tmp/build/perf/FEATURE-DUMP
feature-dwarf=1
feature-dwarf_getlocations=1
feature-eventfd=1
feature-fortify-source=1
feature-sync-compare-and-swap=1
$
The main thing here is that in the end we'll have -DHAVE_EVENTFD in
CFLAGS, and then the 'perf bench' entry needing that API can be
selectively pruned.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-wkeldwob7dpx6jvtuzl8164k@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f232326f69 upstream.
The purpose of this patch is to streamline error propagation and in particular
to propagate retrieve_ptr_limit() errors for pointer types that are not defining
a ptr_limit such that register-based alu ops against these types can be rejected.
The main rationale is that a gap has been identified by Piotr in the existing
protection against speculatively out-of-bounds loads, for example, in case of
ctx pointers, unprivileged programs can still perform pointer arithmetic. This
can be abused to execute speculatively out-of-bounds loads without restrictions
and thus extract contents of kernel memory.
Fix this by rejecting unprivileged programs that attempt any pointer arithmetic
on unprotected pointer types. The two affected ones are pointer to ctx as well
as pointer to map. Field access to a modified ctx' pointer is rejected at a
later point in time in the verifier, and 7c69673262 ("bpf: Permit map_ptr
arithmetic with opcode add and offset 0") only relevant for root-only use cases.
Risk of unprivileged program breakage is considered very low.
Fixes: 7c69673262 ("bpf: Permit map_ptr arithmetic with opcode add and offset 0")
Fixes: b2157399cc ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9b3827ee6 upstream.
Add support for being able to set the learning attribute on port, and
make sure that the standalone ports start up with learning disabled.
We can remove the code in bcm_sf2 that configured the ports learning
attribute because we want the standalone ports to have learning disabled
by default and port 7 cannot be bridged, so its learning attribute will
not change past its initial configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b1597e64e upstream.
Given we know the max possible value of ptr_limit at the time of retrieving
the latter, add basic assertions, so that the verifier can bail out if
anything looks odd and reject the program. Nothing triggered this so far,
but it also does not hurt to have these.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5871dca25 upstream.
Instead of having the mov32 with aux->alu_limit - 1 immediate, move this
operation to retrieve_ptr_limit() instead to simplify the logic and to
allow for subsequent sanity boundary checks inside retrieve_ptr_limit().
This avoids in future that at the time of the verifier masking rewrite
we'd run into an underflow which would not sign extend due to the nature
of mov32 instruction.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10d2bb2e6b upstream.
retrieve_ptr_limit() computes the ptr_limit for registers with stack and
map_value type. ptr_limit is the size of the memory area that is still
valid / in-bounds from the point of the current position and direction
of the operation (add / sub). This size will later be used for masking
the operation such that attempting out-of-bounds access in the speculative
domain is redirected to remain within the bounds of the current map value.
When masking to the right the size is correct, however, when masking to
the left, the size is off-by-one which would lead to an incorrect mask
and thus incorrect arithmetic operation in the non-speculative domain.
Piotr found that if the resulting alu_limit value is zero, then the
BPF_MOV32_IMM() from the fixup_bpf_calls() rewrite will end up loading
0xffffffff into AX instead of sign-extending to the full 64 bit range,
and as a result, this allows abuse for executing speculatively out-of-
bounds loads against 4GB window of address space and thus extracting the
contents of kernel memory via side-channel.
Fixes: 979d63d50c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce9f24cccd upstream.
Currently, system zones just track ranges of block, that are "important"
fs metadata (bitmaps, group descriptors, journal blocks, etc.). This
however complicates how extent tree (or indirect blocks) can be checked
for inodes that actually track such metadata - currently the journal
inode but arguably we should be treating quota files or resize inode
similarly. We cannot run __ext4_ext_check() on such metadata inodes when
loading their extents as that would immediately trigger the validity
checks and so we just hack around that and special-case the journal
inode. This however leads to a situation that a journal inode which has
extent tree of depth at least one can have invalid extent tree that gets
unnoticed until ext4_cache_extents() crashes.
To overcome this limitation, track inode number each system zone belongs
to (0 is used for zones not belonging to any inode). We can then verify
inode number matches the expected one when verifying extent tree and
thus avoid the false errors. With this there's no need to to
special-case journal inode during extent tree checking anymore so remove
it.
Fixes: 0a944e8a6c ("ext4: don't perform block validity checks on the journal inode")
Reported-by: Wolfgang Frisch <wolfgang.frisch@suse.com>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200728130437.7804-4-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf9a379d09 upstream.
Currently, add_system_zone() just silently merges two added system zones
that overlap. However the overlap should not happen and it generally
suggests that some unrelated metadata overlap which indicates the fs is
corrupted. We should have caught such problems earlier (e.g. in
ext4_check_descriptors()) but add this check as another line of defense.
In later patch we also use this for stricter checking of journal inode
extent tree.
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200728130437.7804-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e77d96b8e upstream.
When creating a new event channel with 2-level events the affinity
needs to be reset initially in order to avoid using an old affinity
from earlier usage of the event channel port. So when tearing an event
channel down reset all affinity bits.
The same applies to the affinity when onlining a vcpu: all old
affinity settings for this vcpu must be reset. As percpu events get
initialized before the percpu event channel hook is called,
resetting of the affinities happens after offlining a vcpu (this is
working, as initial percpu memory is zeroed out).
Cc: stable@vger.kernel.org
Reported-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Link: https://lore.kernel.org/r/20210306161833.4552-2-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 262b003d05 upstream.
When registering a memslot, we check the size and location of that
memslot against the IPA size to ensure that we can provide guest
access to the whole of the memory.
Unfortunately, this check rejects memslot that end-up at the exact
limit of the addressing capability for a given IPA size. For example,
it refuses the creation of a 2GB memslot at 0x8000000 with a 32bit
IPA space.
Fix it by relaxing the check to accept a memslot reaching the
limit of the IPA space.
Fixes: c3058d5da2 ("arm/arm64: KVM: Ensure memslots are within KVM_PHYS_SIZE")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 4.4, 4.9, 4.14, 4.19
Reviewed-by: Andrew Jones <drjones@redhat.com>
Link: https://lore.kernel.org/r/20210311100016.3830038-3-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62456189f3 upstream.
max6658 may report unrealistically high temperature during
the driver initialization, for which, its overtemp alarm pin
also gets asserted. For certain devices implementing overtemp
protection based on that pin, it may further trigger a reset to
the device. By reproducing the problem, the wrong reading is
found to be coincident with changing the conversion rate.
To mitigate this issue, set the stop bit before changing the
conversion rate and unset it thereafter. After such change, the
wrong reading is not reproduced. Apply this change only to the
max6657 kind for now, controlled by flag LM90_PAUSE_ON_CONFIG.
Signed-off-by: Boyang Yu <byu@arista.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7850f4d84 upstream.
There is a deadlock in bm_register_write:
First, in the begining of the function, a lock is taken on the binfmt_misc
root inode with inode_lock(d_inode(root)).
Then, if the user used the MISC_FMT_OPEN_FILE flag, the function will call
open_exec on the user-provided interpreter.
open_exec will call a path lookup, and if the path lookup process includes
the root of binfmt_misc, it will try to take a shared lock on its inode
again, but it is already locked, and the code will get stuck in a deadlock
To reproduce the bug:
$ echo ":iiiii:E::ii::/proc/sys/fs/binfmt_misc/bla:F" > /proc/sys/fs/binfmt_misc/register
backtrace of where the lock occurs (#5):
0 schedule () at ./arch/x86/include/asm/current.h:15
1 0xffffffff81b51237 in rwsem_down_read_slowpath (sem=0xffff888003b202e0, count=<optimized out>, state=state@entry=2) at kernel/locking/rwsem.c:992
2 0xffffffff81b5150a in __down_read_common (state=2, sem=<optimized out>) at kernel/locking/rwsem.c:1213
3 __down_read (sem=<optimized out>) at kernel/locking/rwsem.c:1222
4 down_read (sem=<optimized out>) at kernel/locking/rwsem.c:1355
5 0xffffffff811ee22a in inode_lock_shared (inode=<optimized out>) at ./include/linux/fs.h:783
6 open_last_lookups (op=0xffffc9000022fe34, file=0xffff888004098600, nd=0xffffc9000022fd10) at fs/namei.c:3177
7 path_openat (nd=nd@entry=0xffffc9000022fd10, op=op@entry=0xffffc9000022fe34, flags=flags@entry=65) at fs/namei.c:3366
8 0xffffffff811efe1c in do_filp_open (dfd=<optimized out>, pathname=pathname@entry=0xffff8880031b9000, op=op@entry=0xffffc9000022fe34) at fs/namei.c:3396
9 0xffffffff811e493f in do_open_execat (fd=fd@entry=-100, name=name@entry=0xffff8880031b9000, flags=<optimized out>, flags@entry=0) at fs/exec.c:913
10 0xffffffff811e4a92 in open_exec (name=<optimized out>) at fs/exec.c:948
11 0xffffffff8124aa84 in bm_register_write (file=<optimized out>, buffer=<optimized out>, count=19, ppos=<optimized out>) at fs/binfmt_misc.c:682
12 0xffffffff811decd2 in vfs_write (file=file@entry=0xffff888004098500, buf=buf@entry=0xa758d0 ":iiiii:E::ii::i:CF
", count=count@entry=19, pos=pos@entry=0xffffc9000022ff10) at fs/read_write.c:603
13 0xffffffff811defda in ksys_write (fd=<optimized out>, buf=0xa758d0 ":iiiii:E::ii::i:CF
", count=19) at fs/read_write.c:658
14 0xffffffff81b49813 in do_syscall_64 (nr=<optimized out>, regs=0xffffc9000022ff58) at arch/x86/entry/common.c:46
15 0xffffffff81c0007c in entry_SYSCALL_64 () at arch/x86/entry/entry_64.S:120
To solve the issue, the open_exec call is moved to before the write
lock is taken by bm_register_write
Link: https://lkml.kernel.org/r/20210228224414.95962-1-liorribak@gmail.com
Fixes: 948b701a60 ("binfmt_misc: add persistent opened binary handler for containers")
Signed-off-by: Lior Ribak <liorribak@gmail.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbf78d8507 ]
With clang-13, some functions only get partially inlined, with a
specialized version referring to a global variable. This triggers a
harmless build-time check for the intel-rng driver:
WARNING: modpost: drivers/char/hw_random/intel-rng.o(.text+0xe): Section mismatch in reference from the function stop_machine() to the function .init.text:intel_rng_hw_init()
The function stop_machine() references
the function __init intel_rng_hw_init().
This is often because stop_machine lacks a __init
annotation or the annotation of intel_rng_hw_init is wrong.
In this instance, an easy workaround is to force the stop_machine()
function to be inline, along with related interfaces that did not show the
same behavior at the moment, but theoretically could.
The combination of the two patches listed below triggers the behavior in
clang-13, but individually these commits are correct.
Link: https://lkml.kernel.org/r/20210225130153.1956990-1-arnd@kernel.org
Fixes: fe5595c074 ("stop_machine: Provide stop_machine_cpuslocked()")
Fixes: ee527cd3a2 ("Use stop_machine_run in the Intel RNG driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14fbbc8297 ]
Commit b0841eefd9 ("configfs: provide exclusion between IO and removals")
uses ->frag_dead to mark the fragment state, thus no bothering with extra
refcount on config_item when opening a file. The configfs_get_config_item
was removed in __configfs_open_file, but not with config_item_put. So the
refcount on config_item will lost its balance, causing use-after-free
issues in some occasions like this:
Test:
1. Mount configfs on /config with read-only items:
drwxrwx--- 289 root root 0 2021-04-01 11:55 /config
drwxr-xr-x 2 root root 0 2021-04-01 11:54 /config/a
--w--w--w- 1 root root 4096 2021-04-01 11:53 /config/a/1.txt
......
2. Then run:
for file in /config
do
echo $file
grep -R 'key' $file
done
3. __configfs_open_file will be called in parallel, the first one
got called will do:
if (file->f_mode & FMODE_READ) {
if (!(inode->i_mode & S_IRUGO))
goto out_put_module;
config_item_put(buffer->item);
kref_put()
package_details_release()
kfree()
the other one will run into use-after-free issues like this:
BUG: KASAN: use-after-free in __configfs_open_file+0x1bc/0x3b0
Read of size 8 at addr fffffff155f02480 by task grep/13096
CPU: 0 PID: 13096 Comm: grep VIP: 00 Tainted: G W 4.14.116-kasan #1
TGID: 13096 Comm: grep
Call trace:
dump_stack+0x118/0x160
kasan_report+0x22c/0x294
__asan_load8+0x80/0x88
__configfs_open_file+0x1bc/0x3b0
configfs_open_file+0x28/0x34
do_dentry_open+0x2cc/0x5c0
vfs_open+0x80/0xe0
path_openat+0xd8c/0x2988
do_filp_open+0x1c4/0x2fc
do_sys_open+0x23c/0x404
SyS_openat+0x38/0x48
Allocated by task 2138:
kasan_kmalloc+0xe0/0x1ac
kmem_cache_alloc_trace+0x334/0x394
packages_make_item+0x4c/0x180
configfs_mkdir+0x358/0x740
vfs_mkdir2+0x1bc/0x2e8
SyS_mkdirat+0x154/0x23c
el0_svc_naked+0x34/0x38
Freed by task 13096:
kasan_slab_free+0xb8/0x194
kfree+0x13c/0x910
package_details_release+0x524/0x56c
kref_put+0xc4/0x104
config_item_put+0x24/0x34
__configfs_open_file+0x35c/0x3b0
configfs_open_file+0x28/0x34
do_dentry_open+0x2cc/0x5c0
vfs_open+0x80/0xe0
path_openat+0xd8c/0x2988
do_filp_open+0x1c4/0x2fc
do_sys_open+0x23c/0x404
SyS_openat+0x38/0x48
el0_svc_naked+0x34/0x38
To fix this issue, remove the config_item_put in
__configfs_open_file to balance the refcount of config_item.
Fixes: b0841eefd9 ("configfs: provide exclusion between IO and removals")
Signed-off-by: Daiyue Zhang <zhangdaiyue1@huawei.com>
Signed-off-by: Yi Chen <chenyi77@huawei.com>
Signed-off-by: Ge Qiu <qiuge@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53cb245454 ]
An xattr 'get' handler is expected to return the length of the value on
success, yet _nfs4_get_security_label() (and consequently also
nfs4_xattr_get_nfs4_label(), which is used as an xattr handler) returns
just 0 on success.
Fix this by returning label.len instead, which contains the length of
the result.
Fixes: aa9c266962 ("NFS: Client implementation of Labeled-NFS")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: James Morris <jamorris@linux.microsoft.com>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75be7fb7f9 ]
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d3 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 148e34fd33 upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
parameter. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the parameter
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit edf4537bcb ("staging: comedi:
pcl818: use comedi_buf_write_samples()") but the patch applies better to
commit d615416de6 ("staging: comedi: pcl818: introduce
pcl818_ai_write_sample()").]
Fixes: d615416de6 ("staging: comedi: pcl818: introduce pcl818_ai_write_sample()")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-10-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a084303a64 upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: 1f44c034de ("staging: comedi: pcl711: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-9-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b39dfcced3 upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: de88924f67 ("staging: comedi: me4000: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-8-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54999c0d94 upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit 1700529b24 ("staging: comedi:
dmm32at: use comedi_buf_write_samples()") but the patch applies better
to the later (but in the same kernel release) commit 0c0eadadcb
("staging: comedi: dmm32at: introduce dmm32_ai_get_sample()").]
Fixes: 0c0eadadcb ("staging: comedi: dmm32at: introduce dmm32_ai_get_sample()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-7-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 459b1e8c8f upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: ad9eb43c93 ("staging: comedi: das800: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-6-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c0f20b787 upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: d1d24cb65e ("staging: comedi: das6402: read analog input samples in interrupt handler")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-5-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2e78630f7 upstream.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variables
holding the sample value to `unsigned short`. The type of the `val`
parameter of `pci1710_ai_read_sample()` is changed to `unsigned short *`
accordingly. The type of the `val` variable in `pci1710_ai_insn_read()`
is also changed to `unsigned short` since its address is passed to
`pci1710_ai_read_sample()`.
Fixes: a9c3a015c1 ("staging: comedi: adv_pci1710: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-4-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac0bbf55ed upstream.
The digital input subdevice supports Comedi asynchronous commands that
read interrupt status information. This uses 16-bit Comedi samples (of
which only the bottom 8 bits contain status information). However, the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit variable `unsigned int status`. On a bigendian
machine, this will copy 2 bytes from the wrong end of the variable. Fix
it by changing the type of the variable to `unsigned short`.
Fixes: a8c66b684e ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions")
Cc: <stable@vger.kernel.org> #4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25317f428a upstream.
The Change-Of-State (COS) subdevice supports Comedi asynchronous
commands to read 16-bit change-of-state values. However, the interrupt
handler is calling `comedi_buf_write_samples()` with the address of a
32-bit integer `&s->state`. On bigendian architectures, it will copy 2
bytes from the wrong end of the 32-bit integer. Fix it by transferring
the value via a 16-bit integer.
Fixes: 6bb45f2b0c ("staging: comedi: addi_apci_1032: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 718ad9693e upstream.
attach_store() is invoked when user requests import (attach) a device
from usbip host.
Attach and detach are governed by local state and shared state
- Shared state (usbip device status) - Device status is used to manage
the attach and detach operations on import-able devices.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- Device has to be in the right state to be attached and detached.
Attach sequence includes validating the socket and creating receive (rx)
and transmit (tx) threads to talk to the host to get access to the
imported device. rx and tx threads depends on local and shared state to
be correct and in sync.
Detach sequence shuts the socket down and stops the rx and tx threads.
Detach sequence relies on local and shared states to be in sync.
There are races in updating the local and shared status in the current
attach sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to VDEV_ST_NOTASSIGNED. This opens
up a race condition between the threads, port connect, and detach
handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold vhci and usbip_device locks to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to VDEV_ST_NOTASSIGNED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the attach sequence.
- Update usbip_device tcp_rx and tcp_tx pointers holding vhci and
usbip_device locks.
Tested with syzbot reproducer:
- https://syzkaller.appspot.com/text?tag=ReproC&x=14801034d00000
Fixes: 9720b4bc76 ("staging/usbip: convert to kthread")
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+bf1a360e305ee719e364@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+95ce4b142579611ef0a9@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/bb434bd5d7a64fbec38b5ecfb838a6baef6eb12b.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9380afd6df upstream.
usbip_sockfd_store() is invoked when user requests attach (import)
detach (unimport) usb device from usbip host. vhci_hcd sends import
request and usbip_sockfd_store() exports the device if it is free
for export.
Export and unexport are governed by local state and shared state
- Shared state (usbip device status, sockfd) - sockfd and Device
status are used to determine if stub should be brought up or shut
down.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- While the device is exported, device status is marked used and socket,
sockfd, and thread pointers are valid.
Export sequence (stub-up) includes validating the socket and creating
receive (rx) and transmit (tx) threads to talk to the client to provide
access to the exported device. rx and tx threads depends on local and
shared state to be correct and in sync.
Unexport (stub-down) sequence shuts the socket down and stops the rx and
tx threads. Stub-down sequence relies on local and shared states to be
in sync.
There are races in updating the local and shared status in the current
stub-up sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to SDEV_ST_USED. This opens up a
race condition between the threads and usbip_sockfd_store() stub up
and down handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold usbip_device lock to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to SDEV_ST_USED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is a
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the stub-up sequence.
Tested with syzbot reproducer:
- https://syzkaller.appspot.com/text?tag=ReproC&x=14801034d00000
Fixes: 9720b4bc76 ("staging/usbip: convert to kthread")
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+bf1a360e305ee719e364@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+95ce4b142579611ef0a9@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/268a0668144d5ff36ec7d87fdfa90faf583b7ccc.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5563b3b642 upstream.
Add PID for CH340 that's found on cheap programmers.
The driver works flawlessly as soon as the new PID (0x9986) is added to it.
These look like ANU232MI but ship with a ch341 inside. They have no special
identifiers (mine only has the string "DB9D20130716" printed on the PCB and
nothing identifiable on the packaging. The merchant i bought it from
doesn't sell these anymore).
the lsusb -v output is:
Bus 001 Device 009: ID 9986:7523
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x9986
idProduct 0x7523
bcdDevice 2.54
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0027
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 96mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 1
bInterfaceProtocol 2
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
Signed-off-by: Niv Sardi <xaiki@evilgiggle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 253f588c70 upstream.
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1d25e6ee5 upstream.
According to the datasheet, this controller has a restriction
which "set an endpoint number so that combinations of the DIR bit and
the EPNUM bits do not overlap.". However, since the udc core driver is
possible to assign a bulk pipe as an interrupt endpoint, an endpoint
number may not match the pipe number. After that, when user rebinds
another gadget driver, this driver broke the restriction because
the driver didn't clear any configuration in usb_ep_disable().
Example:
# modprobe g_ncm
Then, EP3 = pipe 3, EP4 = pipe 4, EP5 = pipe 6
# rmmod g_ncm
# modprobe g_hid
Then, EP3 = pipe 6, EP4 = pipe 7.
So, pipe 3 and pipe 6 are set as EP3.
So, clear PIPECFG register in usbhs_pipe_free().
Fixes: dfb87b8bfe ("usb: renesas_usbhs: gadget: fix re-enabling pipe without re-connecting")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1615168538-26101-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 789ea77310 upstream.
As per UAC2 Audio Data Formats spec (2.3.1.1 USB Packets),
if the sampling rate is a constant, the allowable variation
of number of audio slots per virtual frame is +/- 1 audio slot.
It means that endpoint should be able to accept/send +1 audio
slot.
Previous endpoint max_packet_size calculation code
was adding sometimes +1 audio slot due to DIV_ROUND_UP
behaviour which was rounding up to closest integer.
However this doesn't work if the numbers are divisible.
It had no any impact with Linux hosts which ignore
this issue, but in case of more strict Windows it
caused rejected enumeration
Thus always add +1 audio slot to endpoint's max packet size
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Cc: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org> #v4.3+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-2-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d8654e81d upstream.
The CDC ACM driver is false matching the Goodix Fingerprint device
against the USB_CDC_ACM_PROTO_AT_V25TER.
The Goodix Fingerprint device is a biometrics sensor that should be
handled in user-space. libfprint has some support for Goodix
fingerprint sensors, although not for this particular one. It is
possible that the vendor allocates a PID per OEM (Lenovo, Dell etc).
If this happens to be the case then more devices from the same vendor
could potentially match the ACM modem module table.
Signed-off-by: Yorick de Wid <ydewid@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210213144901.53199-1-ydewid@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66f669a272 upstream.
Prevent that an IO request is build during device shutdown initiated by
a driver unbind. This request will never be able to be processed or
canceled and will hang forever. This will lead also to a hanging unbind.
Fix by checking not only if the device is in READY state but also check
that there is no device offline initiated before building a new IO request.
Fixes: e443343e50 ("s390/dasd: blk-mq conversion")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Tested-by: Bjoern Walk <bwalk@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d365bd0bf upstream.
In case of an unbind of the DASD device driver the function
dasd_generic_remove() is called which shuts down the device.
Among others this functions removes the int_handler from the cdev.
During shutdown the device cancels all outstanding IO requests and waits
for completion of the clear request.
Unfortunately the clear interrupt will never be received when there is no
interrupt handler connected.
Fix by moving the int_handler removal after the call to the state machine
where no request or interrupt is outstanding.
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Tested-by: Bjoern Walk <bwalk@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b0c2d3eaa upstream.
It turns out that there are in fact userspace implementations that
care and this recent change caused a regression.
https://github.com/containers/buildah/issues/3071
As the motivation for the original change was future development,
and the impact is existing real world code just revert this change
and allow the ambiguity in v3 file caps.
Cc: stable@vger.kernel.org
Fixes: 95ebabde38 ("capabilities: Don't allow writing ambiguous v3 file capabilities")
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ff9dde42e upstream.
When HD-audio bus receives unsolicited events during its system
suspend/resume (S3 and S4) phase, the controller driver may still try
to process events although the codec chips are already (or yet)
powered down. This might screw up the codec communication, resulting
in CORB/RIRB errors. Such events should be rather skipped, as the
codec chip status such as the jack status will be fully refreshed at
the system resume time.
Since we're tracking the system suspend/resume state in codec
power.power_state field, let's add the check in the common unsol event
handler entry point to filter out such events.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org> # 183ab39eb0: ALSA: hda: Initialize power_state
Link: https://lore.kernel.org/r/20210310112809.9215-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28e96c1693 upstream.
The commit c02f77d32d ("ALSA: hda - Workaround for crackled sound on
AMD controller (1022:1457)") introduced a few workarounds for the
recent AMD HD-audio controller, and one of them is the forced BATCH
PCM mode so that PulseAudio avoids the timer-based scheduling. This
was thought to cover for some badly working applications, but this
actually worsens for more others. In total, this wasn't a good idea
to enforce it.
This is a partial revert of the commit above for dropping the PCM
BATCH enforcement part to recover from the regression again.
Fixes: c02f77d32d ("ALSA: hda - Workaround for crackled sound on AMD controller (1022:1457)")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195303
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210308160726.22930-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d28d48c699 ]
If iscsi_prep_scsi_cmd_pdu() fails we try to add it back to the cmdqueue,
but we leave it partially setup. We don't have functions that can undo the
pdu and init task setup. We only have cleanup_task which can clean up both
parts. So this has us just fail the cmd and go through the standard cleanup
routine and then have the SCSI midlayer retry it like is done when it fails
in the queuecommand path.
Link: https://lore.kernel.org/r/20210207044608.27585-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62c8dca9e1 ]
Avoid a potentially large stack frame and overflow by making
"cpumask_t avail" a static variable. There is no concurrent
access due to the existing locking.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42814c438a ]
The for_each_available_child_of_node helper internally makes use of the
of_get_next_available_child() which performs an of_node_get() on each
iteration when searching for next available child node.
Should an available child node be found, then it would return a device
node pointer with reference count incremented, thus early return from
the middle of the loop requires an explicit of_node_put() to prevent
reference count leak.
To stop the reference leak, explicitly call of_node_put() before
returning after an error occurred.
Link: https://lore.kernel.org/r/20210120184810.3068794-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93c00e5f9 ]
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained IRQ
handler").
Based on the mail discussion, it seems ok to drop the error handling.
Link: https://lore.kernel.org/r/20210115212435.19940-3-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d137845c97 ]
While sampling for marked events, currently we record the sample only
if the SIAR valid bit of Sampled Instruction Event Register (SIER) is
set. SIAR_VALID bit is used for fetching the instruction address from
Sampled Instruction Address Register(SIAR). But there are some
usecases, where the user is interested only in the PMU stats at each
counter overflow and the exact IP of the overflow event is not
required. Dropping SIAR invalid samples will fail to record some of
the counter overflows in such cases.
Example of such usecase is dumping the PMU stats (event counts) after
some regular amount of instructions/events from the userspace (ex: via
ptrace). Here counter overflow is indicated to userspace via signal
handler, and captured by monitoring and enabling I/O signaling on the
event file descriptor. In these cases, we expect to get
sample/overflow indication after each specified sample_period.
Perf event attribute will not have PERF_SAMPLE_IP set in the
sample_type if exact IP of the overflow event is not requested. So
while profiling if SAMPLE_IP is not set, just record the counter
overflow irrespective of SIAR_VALID check.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
[mpe: Reflow comment and if formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1612516492-1428-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0354ca6edd ]
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63c9e47a16 ]
When extending a file, udf_do_extend_file() may enter following empty
indirect extent. At the end of udf_do_extend_file() we revert prev_epos
to point to the last written extent. However if we end up not adding any
further extent in udf_do_extend_file(), the reverting points prev_epos
into the header area of the AED and following updates of the extents
(in udf_update_extents()) will corrupt the header.
Make sure that we do not follow indirect extent if we are not going to
add any more extents so that returning back to the last written extent
works correctly.
Link: https://lore.kernel.org/r/20210107234116.6190-2-magnani@ieee.org
Signed-off-by: Steven J. Magnani <magnani@ieee.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9032dba5a ]
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846e ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8a7e27fd5c upstream.
usbtv doesn't support power management, so on system suspend the
.disconnect callback of the driver is called. The teardown sequence
includes a call to snd_card_free. Its implementation waits until the
refcount of the sound card device drops to zero, however, if its file is
open, snd_card_file_add takes a reference, which can't be dropped during
the suspend, because the userspace processes are already frozen at this
point. snd_card_free waits for completion forever, leading to a hang on
suspend.
This commit fixes this deadlock condition by replacing snd_card_free
with snd_card_free_when_closed, that doesn't wait until all references
are released, allowing suspend to progress.
Fixes: 63ddf68de5 ("[media] usbtv: add audio support")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3e860a833 upstream.
If clear GMAC_CONFIG_TE bit, it would stop all tx channels, but users
may only want to stop specific tx channel.
Fixes: 48863ce594 ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac88c531a5 upstream.
When the probe fails or requests to be defered, we must disable the
regulator that was previously enabled.
Fixes: 7994fe55a4 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7d9d48545 upstream.
For the devices in this driver, the default qdisc is "noqueue",
because their "tx_queue_len" is 0.
In function "__dev_queue_xmit" in "net/core/dev.c", devices with the
"noqueue" qdisc are specially handled. Packets are transmitted without
being queued after a "dev->flags & IFF_UP" check. However, it's possible
that even if this check succeeds, "ops->ndo_stop" may still have already
been called. This is because in "__dev_close_many", "ops->ndo_stop" is
called before clearing the "IFF_UP" flag.
If we call "netif_stop_queue" in "ops->ndo_stop", then it's possible in
"__dev_queue_xmit", it sees the "IFF_UP" flag is present, and then it
checks "netif_xmit_stopped" and finds that the queue is already stopped.
In this case, it will complain that:
"Virtual device ... asks to queue packet!"
To prevent "__dev_queue_xmit" from generating this complaint, we should
not call "netif_stop_queue" in "ops->ndo_stop".
We also don't need to call "netif_start_queue" in "ops->ndo_open",
because after a netdev is allocated and registered, the
"__QUEUE_STATE_DRV_XOFF" flag is initially not set, so there is no need
to call "netif_start_queue" to clear it.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad5d07f4a9 upstream.
The current CIPSO and CALIPSO refcounting scheme for the DOI
definitions is a bit flawed in that we:
1. Don't correctly match gets/puts in netlbl_cipsov4_list().
2. Decrement the refcount on each attempt to remove the DOI from the
DOI list, only removing it from the list once the refcount drops
to zero.
This patch fixes these problems by adding the missing "puts" to
netlbl_cipsov4_list() and introduces a more conventional, i.e.
not-buggy, refcounting mechanism to the DOI definitions. Upon the
addition of a DOI to the DOI list, it is initialized with a refcount
of one, removing a DOI from the list removes it from the list and
drops the refcount by one; "gets" and "puts" behave as expected with
respect to refcounts, increasing and decreasing the DOI's refcount by
one.
Fixes: b1edeb1023 ("netlabel: Replace protocol/NetLabel linking with refrerence counts")
Fixes: d7cce01504 ("netlabel: Add support for removing a CALIPSO DOI.")
Reported-by: syzbot+9ec037722d2603a9f52e@syzkaller.appspotmail.com
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c59cff38e upstream.
There's no reason for preventing the creation and removal
of qmimux network interfaces when the underlying interface
is up.
This makes qmi_wwan mux implementation more similar to the
rmnet one, simplifying userspace management of the same
logical interfaces.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfc2560563 upstream.
This is a follow up of commit ea32746953 ("net: sched: avoid
duplicates in qdisc dump") which has fixed the issue only for the qdisc
dump.
The duplicate printing also occurs when dumping the classes via
tc class show dev eth0
Fixes: 59cc1f61f0 ("net: sched: convert qdisc linked list to hashtable")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 879c348c35 upstream.
We introduce dwmac410_dma_init_channel() here for both EQoS v4.10 and
above which use different DMA_CH(n)_Interrupt_Enable bit definitions for
NIE and AIE.
Fixes: 48863ce594 ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00ff801bb8 upstream.
This patch fixes a bug that the moderation config will not be
applied when calling mlx4_en_reset_config. For example, when
turning on rx timestamping, mlx4_en_reset_config() will be called,
causing the NIC to forget previous moderation config.
This fix is in phase with a previous fix:
commit 79c54b6bbf ("net/mlx4_en: Fix TX moderation info loss
after set_ringparam is called")
Tested: Before this patch, on a host with NIC using mlx4, run
netserver and stream TCP to the host at full utilization.
$ sar -I SUM 1
INTR intr/s
14:03:56 sum 48758.00
After rx hwtstamp is enabled:
$ sar -I SUM 1
14:10:38 sum 317771.00
We see the moderation is not working properly and issued 7x more
interrupts.
After the patch, and turned on rx hwtstamp, the rate of interrupts
is as expected:
$ sar -I SUM 1
14:52:11 sum 49332.00
Fixes: 79c54b6bbf ("net/mlx4_en: Fix TX moderation info loss after set_ringparam is called")
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
CC: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c91bc3d44 upstream.
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b1ea29bc0 upstream.
This reverts commit 8ff60eb052.
The kernel test robot reports a huge performance regression due to the
commit, and the reason seems fairly straightforward: when there is
contention on the page list (which is what causes acquire_slab() to
fail), we do _not_ want to just loop and try again, because that will
transfer the contention to the 'n->list_lock' spinlock we hold, and
just make things even worse.
This is admittedly likely a problem only on big machines - the kernel
test robot report comes from a 96-thread dual socket Intel Xeon Gold
6252 setup, but the regression there really is quite noticeable:
-47.9% regression of stress-ng.rawpkt.ops_per_sec
and the commit that was marked as being fixed (7ced371971: "slub:
Acquire_slab() avoid loop") actually did the loop exit early very
intentionally (the hint being that "avoid loop" part of that commit
message), exactly to avoid this issue.
The correct thing to do may be to pick some kind of reasonable middle
ground: instead of breaking out of the loop on the very first sign of
contention, or trying over and over and over again, the right thing may
be to re-try _once_, and then give up on the second failure (or pick
your favorite value for "once"..).
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/lkml/20210301080404.GF12822@xsang-OptiPlex-9020/
Cc: Jann Horn <jannh@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c8e2f6d3d upstream.
When building with -ffunction-sections, the compiler will place each
function into its own ELF section, prefixed with ".text". For example,
a simple test module with functions test_module_do_work() and
test_module_wq_func():
% objdump --section-headers test_module.o | awk '/\.text/{print $2}'
.text
.text.test_module_do_work
.text.test_module_wq_func
.init.text
.exit.text
Adjust the recordmcount scripts to look for ".text" as a section name
prefix. This will ensure that those functions will be included in the
__mcount_loc relocations:
% objdump --reloc --section __mcount_loc test_module.o
OFFSET TYPE VALUE
0000000000000000 R_X86_64_64 .text.test_module_do_work
0000000000000008 R_X86_64_64 .text.test_module_wq_func
0000000000000010 R_X86_64_64 .init.text
Link: http://lkml.kernel.org/r/1542745158-25392-2-git-send-email-joe.lawrence@redhat.com
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Manoj Gupta <manojgupta@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14302ee330 upstream.
In cifs_statfs(), if server->ops->queryfs is not NULL, then we should
use its return value rather than always returning 0. Instead, use rc
variable as it is properly set to 0 in case there is no
server->ops->queryfs.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 449052cfeb upstream.
Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is
asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although
the reset value is 1b'1. This is a prepare patch, later patch will
invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze
mode acknowledge.
Fixes: b1aa1c7a21 ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze")
Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e940e0895a upstream.
There are two ref count variables controlling the free()ing of a socket:
- struct sock::sk_refcnt - which is changed by sock_hold()/sock_put()
- struct sock::sk_wmem_alloc - which accounts the memory allocated by
the skbs in the send path.
In case there are still TX skbs on the fly and the socket() is closed,
the struct sock::sk_refcnt reaches 0. In the TX-path the CAN stack
clones an "echo" skb, calls sock_hold() on the original socket and
references it. This produces the following back trace:
| WARNING: CPU: 0 PID: 280 at lib/refcount.c:25 refcount_warn_saturate+0x114/0x134
| refcount_t: addition on 0; use-after-free.
| Modules linked in: coda_vpu(E) v4l2_jpeg(E) videobuf2_vmalloc(E) imx_vdoa(E)
| CPU: 0 PID: 280 Comm: test_can.sh Tainted: G E 5.11.0-04577-gf8ff6603c617 #203
| Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
| Backtrace:
| [<80bafea4>] (dump_backtrace) from [<80bb0280>] (show_stack+0x20/0x24) r7:00000000 r6:600f0113 r5:00000000 r4:81441220
| [<80bb0260>] (show_stack) from [<80bb593c>] (dump_stack+0xa0/0xc8)
| [<80bb589c>] (dump_stack) from [<8012b268>] (__warn+0xd4/0x114) r9:00000019 r8:80f4a8c2 r7:83e4150c r6:00000000 r5:00000009 r4:80528f90
| [<8012b194>] (__warn) from [<80bb09c4>] (warn_slowpath_fmt+0x88/0xc8) r9:83f26400 r8:80f4a8d1 r7:00000009 r6:80528f90 r5:00000019 r4:80f4a8c2
| [<80bb0940>] (warn_slowpath_fmt) from [<80528f90>] (refcount_warn_saturate+0x114/0x134) r8:00000000 r7:00000000 r6:82b44000 r5:834e5600 r4:83f4d540
| [<80528e7c>] (refcount_warn_saturate) from [<8079a4c8>] (__refcount_add.constprop.0+0x4c/0x50)
| [<8079a47c>] (__refcount_add.constprop.0) from [<8079a57c>] (can_put_echo_skb+0xb0/0x13c)
| [<8079a4cc>] (can_put_echo_skb) from [<8079ba98>] (flexcan_start_xmit+0x1c4/0x230) r9:00000010 r8:83f48610 r7:0fdc0000 r6:0c080000 r5:82b44000 r4:834e5600
| [<8079b8d4>] (flexcan_start_xmit) from [<80969078>] (netdev_start_xmit+0x44/0x70) r9:814c0ba0 r8:80c8790c r7:00000000 r6:834e5600 r5:82b44000 r4:82ab1f00
| [<80969034>] (netdev_start_xmit) from [<809725a4>] (dev_hard_start_xmit+0x19c/0x318) r9:814c0ba0 r8:00000000 r7:82ab1f00 r6:82b44000 r5:00000000 r4:834e5600
| [<80972408>] (dev_hard_start_xmit) from [<809c6584>] (sch_direct_xmit+0xcc/0x264) r10:834e5600 r9:00000000 r8:00000000 r7:82b44000 r6:82ab1f00 r5:834e5600 r4:83f27400
| [<809c64b8>] (sch_direct_xmit) from [<809c6c0c>] (__qdisc_run+0x4f0/0x534)
To fix this problem, only set skb ownership to sockets which have still
a ref count > 0.
Fixes: 0ae89beb28 ("can: add destructor for self generated skbs")
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Andre Naujoks <nautsch2@gmail.com>
Link: https://lore.kernel.org/r/20210226092456.27126-1-o.rempel@pengutronix.de
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d348ede32e upstream.
A packet with skb_inner_network_header(skb) == skb_network_header(skb)
and ETH_P_MPLS_UC will prevent mpls_gso_segment from pulling any headers
from the packet. Subsequently, the call to skb_mac_gso_segment will
again call mpls_gso_segment with the same packet leading to an infinite
loop. In addition, ensure that the header length is a multiple of four,
which should hold irrespective of the number of stacked labels.
Signed-off-by: Balazs Nemeth <bnemeth@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 924a9bc362 upstream.
For gso packets, virtio_net_hdr_set_proto sets the protocol (if it isn't
set) based on the type in the virtio net hdr, but the skb could contain
anything since it could come from packet_snd through a raw socket. If
there is a mismatch between what virtio_net_hdr_set_proto sets and
the actual protocol, then the skb could be handled incorrectly later
on.
An example where this poses an issue is with the subsequent call to
skb_flow_dissect_flow_keys_basic which relies on skb->protocol being set
correctly. A specially crafted packet could fool
skb_flow_dissect_flow_keys_basic preventing EINVAL to be returned.
Avoid blindly trusting the information provided by the virtio net header
by checking that the protocol in the packet actually matches the
protocol set by virtio_net_hdr_set_proto. Note that since the protocol
is only checked if skb->dev implements header_ops->parse_protocol,
packets from devices without the implementation are not checked at this
stage.
Fixes: 9274124f02 ("net: stricter validation of untrusted gso packets")
Signed-off-by: Balazs Nemeth <bnemeth@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e78b291551 upstream.
Introduce a new optional header_ops callback called parse_protocol and a
wrapper function dev_parse_header_protocol, similar to dev_parse_header.
The new callback's purpose is to extract the protocol number from the L2
header, the format of which is known to the driver, but not to the upper
layers of the stack.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89e5c58fc1 upstream.
We noticed a GRO issue for UDP-based encaps such as vxlan/geneve when the
csum for the UDP header itself is 0. In that case, GRO aggregation does
not take place on the phys dev, but instead is deferred to the vxlan/geneve
driver (see trace below).
The reason is essentially that GRO aggregation bails out in udp_gro_receive()
for such case when drivers marked the skb with CHECKSUM_UNNECESSARY (ice, i40e,
others) where for non-zero csums 2abb7cdc0d ("udp: Add support for doing
checksum unnecessary conversion") promotes those skbs to CHECKSUM_COMPLETE
and napi context has csum_valid set. This is however not the case for zero
UDP csum (here: csum_cnt is still 0 and csum_valid continues to be false).
At the same time 57c67ff4bd ("udp: additional GRO support") added matches
on !uh->check ^ !uh2->check as part to determine candidates for aggregation,
so it certainly is expected to handle zero csums in udp_gro_receive(). The
purpose of the check added via 662880f442 ("net: Allow GRO to use and set
levels of checksum unnecessary") seems to catch bad csum and stop aggregation
right away.
One way to fix aggregation in the zero case is to only perform the !csum_valid
check in udp_gro_receive() if uh->check is infact non-zero.
Before:
[...]
swapper 0 [008] 731.946506: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100400 len=1500 (1)
swapper 0 [008] 731.946507: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100200 len=1500
swapper 0 [008] 731.946507: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101100 len=1500
swapper 0 [008] 731.946508: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101700 len=1500
swapper 0 [008] 731.946508: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101b00 len=1500
swapper 0 [008] 731.946508: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100600 len=1500
swapper 0 [008] 731.946508: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100f00 len=1500
swapper 0 [008] 731.946509: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100a00 len=1500
swapper 0 [008] 731.946516: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100500 len=1500
swapper 0 [008] 731.946516: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100700 len=1500
swapper 0 [008] 731.946516: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101d00 len=1500 (2)
swapper 0 [008] 731.946517: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101000 len=1500
swapper 0 [008] 731.946517: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101c00 len=1500
swapper 0 [008] 731.946517: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101400 len=1500
swapper 0 [008] 731.946518: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100e00 len=1500
swapper 0 [008] 731.946518: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497101600 len=1500
swapper 0 [008] 731.946521: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff966497100800 len=774
swapper 0 [008] 731.946530: net:netif_receive_skb: dev=test_vxlan skbaddr=0xffff966497100400 len=14032 (1)
swapper 0 [008] 731.946530: net:netif_receive_skb: dev=test_vxlan skbaddr=0xffff966497101d00 len=9112 (2)
[...]
# netperf -H 10.55.10.4 -t TCP_STREAM -l 20
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.55.10.4 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 20.01 13129.24
After:
[...]
swapper 0 [026] 521.862641: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff93ab0d479000 len=11286 (1)
swapper 0 [026] 521.862643: net:netif_receive_skb: dev=test_vxlan skbaddr=0xffff93ab0d479000 len=11236 (1)
swapper 0 [026] 521.862650: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff93ab0d478500 len=2898 (2)
swapper 0 [026] 521.862650: net:netif_receive_skb: dev=enp10s0f0 skbaddr=0xffff93ab0d479f00 len=8490 (3)
swapper 0 [026] 521.862653: net:netif_receive_skb: dev=test_vxlan skbaddr=0xffff93ab0d478500 len=2848 (2)
swapper 0 [026] 521.862653: net:netif_receive_skb: dev=test_vxlan skbaddr=0xffff93ab0d479f00 len=8440 (3)
[...]
# netperf -H 10.55.10.4 -t TCP_STREAM -l 20
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.55.10.4 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 20.01 24576.53
Fixes: 57c67ff4bd ("udp: additional GRO support")
Fixes: 662880f442 ("net: Allow GRO to use and set levels of checksum unnecessary")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tom Herbert <tom@herbertland.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20210226212248.8300-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c33cb0020e upstream.
Apparently, <linux/netfilter/nfnetlink_cthelper.h> and
<linux/netfilter/nfnetlink_acct.h> could not be included into the same
compilation unit because of a cut-and-paste typo in the former header.
Fixes: 12f7a50533 ("netfilter: add user-space connection tracking helper infrastructure")
Cc: <stable@vger.kernel.org> # v3.6
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f03c30cb8 ]
The PC_DBG_ECO_CNTL register on the Adreno A5xx family gets
programmed to some different values on a per-model basis.
At least, this is what we intend to do here;
Unfortunately, though, this register is being overwritten with a
static magic number, right after applying the GPU-specific
configuration (including the GPU-specific quirks) and that is
effectively nullifying the efforts.
Let's remove the redundant and wrong write to the PC_DBG_ECO_CNTL
register in order to retain the wanted configuration for the
target GPU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c54cb6c62 ]
Add support for SW_TABLET_MODE on the Acer Switch 10 (SW5-012) and the
acer Switch 10 (S1003) models.
There is no way to detect if this is supported, so this uses DMI based
quirks setting force_caps to ACER_CAP_KBD_DOCK (these devices have no
other acer-wmi based functionality).
The new SW_TABLET_MODE functionality can be tested on devices which
are not in the DMI table by passing acer_wmi.force_caps=0x40 on the
kernel commandline.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-6-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82cb8a5c39 ]
Not all devices supporting WMID_GUID3 support the wmid3_set_function_mode()
call, leading to errors like these:
[ 60.138358] acer_wmi: Enabling RF Button failed: 0x1 - 0xff
[ 60.140036] acer_wmi: Enabling Launch Manager failed: 0x1 - 0xff
Add an ACER_CAP_SET_FUNCTION_MODE capability flag, so that these calls
can be disabled through the new force_caps mechanism.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-5-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39aa009bb6 ]
Add a new force_caps module parameter to allow overriding the drivers
builtin capability detection mechanism.
This can be used to for example:
-Disable rfkill functionality on devices where there is an AA OEM DMI
record advertising non functional rfkill switches
-Force loading of the driver on devices with a missing AA OEM DMI record
Note that force_caps is -1 when unset, this allows forcing the
capability field to 0, which results in acer-wmi only providing WMI
hotkey handling while disabling all other (led, rfkill, backlight)
functionality.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-4-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9feb0763e4 ]
Cleanup accelerometer device handling:
-Drop acer_wmi_accel_destroy instead directly call input_unregister_device.
-The information tracked by the CAP_ACCEL flag mirrors acer_wmi_accel_dev
being NULL. Drop the CAP flag, this is a preparation change for allowing
users to override the capability flags. Dropping the flag stops users
from causing a NULL pointer dereference by forcing the capability.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-3-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4add4d988f ]
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24f6b6036c upstream.
Fix dm_table_supports_zoned_model() and invert logic of both
iterate_devices_callout_fn so that all devices' zoned capabilities are
properly checked.
Add one more parameter to dm_table_any_dev_attr(), which is actually
used as the @data parameter of iterate_devices_callout_fn, so that
dm_table_matches_zone_sectors() can be replaced by
dm_table_any_dev_attr().
Fixes: dd88d313be ("dm table: add zoned block devices validation")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[jeffle: also convert no_sg_merge check]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0fab5089 upstream.
Fix dm_table_supports_dax() and invert logic of both
iterate_devices_callout_fn so that all devices' DAX capabilities are
properly checked.
Fixes: 545ed20e6d ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[jeffle: no dax synchronous]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4c8dd9c2d upstream.
According to the definition of dm_iterate_devices_fn:
* This function must iterate through each section of device used by the
* target until it encounters a non-zero return code, which it then returns.
* Returns zero if no callout returned non-zero.
For some target type (e.g. dm-stripe), one call of iterate_devices() may
iterate multiple underlying devices internally, in which case a non-zero
return code returned by iterate_devices_callout_fn will stop the iteration
in advance. No iterate_devices_callout_fn should return non-zero unless
device iteration should stop.
Rename dm_table_requires_stable_pages() to dm_table_any_dev_attr() and
elevate it for reuse to stop iterating (and return non-zero) on the
first device that causes iterate_devices_callout_fn to return non-zero.
Use dm_table_any_dev_attr() to properly iterate through devices.
Rename device_is_nonrot() to device_is_rotational() and invert logic
accordingly to fix improper disposition.
[jeffle: backport notes]
Also convert the no_sg_merge capability check, which is introduced by
commit 200612ec33 ("dm table: propagate QUEUE_FLAG_NO_SG_MERGE"), and
removed since commit 2705c93742 ("block: kill QUEUE_FLAG_NO_SG_MERGE")
in v5.1.
Fixes: c3c4555edd ("dm table: clear add_random unless all devices have it set")
Fixes: 4693c9668f ("dm table: propagate non rotational flag")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77516d25f5 ]
The copy_to_user() function returns the number of bytes remaining but
we want to return -EFAULT to the user if it can't complete the copy.
The "st" variable only holds zero on success or negative error codes on
failure so the type should be int.
Fixes: 36f988e978 ("rsxx: Adding in debugfs entries.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a9630c72 ]
Currently the mask operation on variable conf is just 3 bits so
the switch statement case value of 8 is unreachable dead code.
The function daio_mgr_dao_init can be passed a 4 bit value,
function dao_rsc_init calls it with conf set to:
conf = (desc->msr & 0x7) | (desc->passthru << 3);
so clearly when desc->passthru is set to 1 then conf can be
at least 8.
Fix this by changing the mask to 0xf.
Fixes: 8cc7236148 ("ALSA: SB X-Fi driver merge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210227001527.1077484-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d70cef0d46 upstream.
When a qstripe is required an extra page is allocated and mapped. There
were 3 problems:
1) There is no corresponding call of kunmap() for the qstripe page.
2) There is no reason to map the qstripe page more than once if the
number of bits set in rbio->dbitmap is greater than one.
3) There is no reason to map the parity page and unmap it each time
through the loop.
The page memory can continue to be reused with a single mapping on each
iteration by raid6_call.gen_syndrome() without remapping. So map the
page for the duration of the loop.
Similarly, improve the algorithm by mapping the parity page just 1 time.
Fixes: 5a6ac9eacb ("Btrfs, raid56: support parity scrub on raid56")
CC: stable@vger.kernel.org # 4.4.x: c17af96554: btrfs: raid56: simplify tracking of Q stripe presence
CC: stable@vger.kernel.org # 4.4.x
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c17af96554 upstream.
There are temporary variables tracking the index of P and Q stripes, but
none of them is really used as such, merely for determining if the Q
stripe is present. This leads to compiler warnings with
-Wunused-but-set-variable and has been reported several times.
fs/btrfs/raid56.c: In function ‘finish_rmw’:
fs/btrfs/raid56.c:1199:6: warning: variable ‘p_stripe’ set but not used [-Wunused-but-set-variable]
1199 | int p_stripe = -1;
| ^~~~~~~~
fs/btrfs/raid56.c: In function ‘finish_parity_scrub’:
fs/btrfs/raid56.c:2356:6: warning: variable ‘p_stripe’ set but not used [-Wunused-but-set-variable]
2356 | int p_stripe = -1;
| ^~~~~~~~
Replace the two variables with one that has a clear meaning and also get
rid of the warnings. The logic that verifies that there are only 2
valid cases is unchanged.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caf6912f3f upstream.
We're not factoring in the start of the file for where to write and
read the swapfile, which leads to very unfortunate side effects of
writing where we should not be...
[This issue only affects swapfiles on filesystems on top of blockdevs
that implement rw_page ops (brd, zram, btt, pmem), and not on top of any
other block devices, in contrast to the upstream commit fix.]
Fixes: dd6bd0d9c7 ("swap: use bdev_read_page() / bdev_write_page()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2395928158 upstream.
There exists multiple path may do zram compaction concurrently.
1. auto-compaction triggered during memory reclaim
2. userspace utils write zram<id>/compaction node
So, multiple threads may call zs_shrinker_scan/zs_compact concurrently.
But pages_compacted is a per zsmalloc pool variable and modification
of the variable is not serialized(through under class->lock).
There are two issues here:
1. the pages_compacted may not equal to total number of pages
freed(due to concurrently add).
2. zs_shrinker_scan may not return the correct number of pages
freed(issued by current shrinker).
The fix is simple:
1. account the number of pages freed in zs_compact locally.
2. use actomic variable pages_compacted to accumulate total number.
Link: https://lkml.kernel.org/r/20210202122235.26885-1-wu-yan@tcl.com
Fixes: 860c707dca ("zsmalloc: account the number of compacted pages")
Signed-off-by: Rokudo Yan <wu-yan@tcl.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8310b77b48 upstream.
Bailing immediately from set_foreign_p2m_mapping() upon a p2m updating
error leaves the full batch in an ambiguous state as far as the caller
is concerned. Instead flags respective slots as bad, unmapping what
was mapped there right away.
HYPERVISOR_grant_table_op()'s return value and the individual unmap
slots' status fields get used only for a one-time - there's not much we
can do in case of a failure.
Note that there's no GNTST_enomem or alike, so GNTST_general_error gets
used.
The map ops' handle fields get overwritten just to be on the safe side.
This is part of XSA-367.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/96cccf5d-e756-5f53-b91a-ea269bfb9be0@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2efc459d06 upstream.
Output defects can exist in sysfs content using sprintf and snprintf.
sprintf does not know the PAGE_SIZE maximum of the temporary buffer
used for outputting sysfs content and it's possible to overrun the
PAGE_SIZE buffer length.
Add a generic sysfs_emit function that knows that the size of the
temporary buffer and ensures that no overrun is done.
Add a generic sysfs_emit_at function that can be used in multiple
call situations that also ensures that no overrun is done.
Validate the output buffer argument to be page aligned.
Validate the offset len argument to be within the PAGE_SIZE buf.
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/884235202216d464d61ee975f7465332c86f76b2.1600285923.git.joe@perches.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 688e8128b7 upstream.
Protect the iSCSI transport handle, available in sysfs, by requiring
CAP_SYS_ADMIN to read it. Also protect the netlink socket by restricting
reception of messages to ones sent with CAP_SYS_ADMIN. This disables
normal users from being able to end arbitrary iSCSI sessions.
Cc: stable@vger.kernel.org
Reported-by: Adam Nichols <adam@grimm-co.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31680c1d15 ]
Bump 64-bit IRQ stack size to 64 KB.
I had a kernel IRQ stack overflow on the mx3210 debian buildd machine. This patch increases the
64-bit IRQ stack size to 64 KB. The 64-bit stack size needs to be larger than the 32-bit stack
size since registers are twice as big.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb73d07148 ]
This is similar to commit
b21ebf2fb4 ("x86: Treat R_X86_64_PLT32 as R_X86_64_PC32")
but for i386. As far as the kernel is concerned, R_386_PLT32 can be
treated the same as R_386_PC32.
R_386_PLT32/R_X86_64_PLT32 are PC-relative relocation types which
can only be used by branches. If the referenced symbol is defined
externally, a PLT will be used.
R_386_PC32/R_X86_64_PC32 are PC-relative relocation types which can be
used by address taking operations and branches. If the referenced symbol
is defined externally, a copy relocation/canonical PLT entry will be
created in the executable.
On x86-64, there is no PIC vs non-PIC PLT distinction and an
R_X86_64_PLT32 relocation is produced for both `call/jmp foo` and
`call/jmp foo@PLT` with newer (2018) GNU as/LLVM integrated assembler.
This avoids canonical PLT entries (st_shndx=0, st_value!=0).
On i386, there are 2 types of PLTs, PIC and non-PIC. Currently,
the GCC/GNU as convention is to use R_386_PC32 for non-PIC PLT and
R_386_PLT32 for PIC PLT. Copy relocations/canonical PLT entries
are possible ABI issues but GCC/GNU as will likely keep the status
quo because (1) the ABI is legacy (2) the change will drop a GNU
ld diagnostic for non-default visibility ifunc in shared objects.
clang-12 -fno-pic (since [1]) can emit R_386_PLT32 for compiler
generated function declarations, because preventing canonical PLT
entries is weighed over the rare ifunc diagnostic.
Further info for the more interested:
https://github.com/ClangBuiltLinux/linux/issues/1210https://sourceware.org/bugzilla/show_bug.cgi?id=27169a084c0388e [1]
[ bp: Massage commit message. ]
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Link: https://lkml.kernel.org/r/20210127205600.1227437-1-maskray@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55379e343 ]
Failed to transmit wmi management frames:
[84977.840894] ath10k_snoc a000000.wifi: wmi mgmt tx queue is full
[84977.840913] ath10k_snoc a000000.wifi: failed to transmit packet, dropping: -28
[84977.840924] ath10k_snoc a000000.wifi: failed to submit frame: -28
[84977.840932] ath10k_snoc a000000.wifi: failed to transmit frame: -28
This issue is caused by race condition between skb_dequeue and
__skb_queue_tail. The queue of ‘wmi_mgmt_tx_queue’ is protected by a
different lock: ar->data_lock vs list->lock, the result is no protection.
So when ath10k_mgmt_over_wmi_tx_work() and ath10k_mac_tx_wmi_mgmt()
running concurrently on different CPUs, there appear to be a rare corner
cases when the queue length is 1,
CPUx (skb_deuque) CPUy (__skb_queue_tail)
next=list
prev=list
struct sk_buff *skb = skb_peek(list); WRITE_ONCE(newsk->next, next);
WRITE_ONCE(list->qlen, list->qlen - 1);WRITE_ONCE(newsk->prev, prev);
next = skb->next; WRITE_ONCE(next->prev, newsk);
prev = skb->prev; WRITE_ONCE(prev->next, newsk);
skb->next = skb->prev = NULL; list->qlen++;
WRITE_ONCE(next->prev, prev);
WRITE_ONCE(prev->next, next);
If the instruction ‘next = skb->next’ is executed before
‘WRITE_ONCE(prev->next, newsk)’, newsk will be lost, as CPUx get the
old ‘next’ pointer, but the length is still added by one. The final
result is the length of the queue will reach the maximum value but
the queue is empty.
So remove ar->data_lock, and use 'skb_queue_tail' instead of
'__skb_queue_tail' to prevent the potential race condition. Also switch
to use skb_queue_len_lockless, in case we queue a few SKBs simultaneously.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1.c2-00033-QCAHLSWMTPLZ-1
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608618887-8857-1-git-send-email-miaoqing@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 275b1e88ca ]
pktgen create threads for all online cpus and bond these threads to
relevant cpu repecivtily. when this thread firstly be woken up, it
will compare cpu currently running with the cpu specified at the time
of creation and if the two cpus are not equal, BUG_ON() will take effect
causing panic on the system.
Notice that these threads could be migrated to other cpus before start
running because of the cpu hotplug after these threads have created. so the
BUG_ON() used here seems unreasonable and we can replace it with WARN_ON()
to just printf a warning other than panic the system.
Signed-off-by: Di Zhu <zhudi21@huawei.com>
Link: https://lore.kernel.org/r/20210125124229.19334-1-zhudi21@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb88d01b67 ]
We can currently get a "command execute failure 19" error on beacon loss
if the signal is weak:
wlcore: Beacon loss detected. roles:0xff
wlcore: Connection loss work (role_id: 0).
...
wlcore: ERROR command execute failure 19
...
WARNING: CPU: 0 PID: 1552 at drivers/net/wireless/ti/wlcore/main.c:803
...
(wl12xx_queue_recovery_work.part.0 [wlcore])
(wl12xx_cmd_role_start_sta [wlcore])
(wl1271_op_bss_info_changed [wlcore])
(ieee80211_prep_connection [mac80211])
Error 19 is defined as CMD_STATUS_WRONG_NESTING from the wlcore firmware,
and seems to mean that the firmware no longer wants to see the quirk
handling for WLCORE_QUIRK_START_STA_FAILS done.
This quirk got added with commit 18eab43070 ("wlcore: workaround
start_sta problem in wl12xx fw"), and it seems that this already got fixed
in the firmware long time ago back in 2012 as wl18xx never had this quirk
in place to start with.
As we no longer even support firmware that early, to me it seems that it's
safe to just drop WLCORE_QUIRK_START_STA_FAILS to fix the error. Looks
like earlier firmware got disabled back in 2013 with commit 0e284c074e
("wl12xx: increase minimum singlerole firmware version required").
If it turns out we still need WLCORE_QUIRK_START_STA_FAILS with any
firmware that the driver works with, we can simply revert this patch and
add extra checks for firmware version used.
With this fix wlcore reconnects properly after a beacon loss.
Cc: Raz Bouganim <r-bouganim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210115065613.7731-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a1ba9da8f0 upstream.
The current code would unnecessarily expand the address range. Consider
one example, (start, end) = (1G-2M, 3G+2M), and (vm_start, vm_end) =
(1G-4M, 3G+4M), the expected adjustment should be keep (1G-2M, 3G+2M)
without expand. But the current result will be (1G-4M, 3G+4M). Actually,
the range (1G-4M, 1G) and (3G, 3G+4M) would never been involved in pmd
sharing.
After this patch, we will check that the vma span at least one PUD aligned
size and the start,end range overlap the aligned range of vma.
With above example, the aligned vma range is (1G, 3G), so if (start, end)
range is within (1G-4M, 1G), or within (3G, 3G+4M), then no adjustment to
both start and end. Otherwise, we will have chance to adjust start
downwards or end upwards without exceeding (vm_start, vm_end).
Mike:
: The 'adjusted range' is used for calls to mmu notifiers and cache(tlb)
: flushing. Since the current code unnecessarily expands the range in some
: cases, more entries than necessary would be flushed. This would/could
: result in performance degradation. However, this is highly dependent on
: the user runtime. Is there a combination of vma layout and calls to
: actually hit this issue? If the issue is hit, will those entries
: unnecessarily flushed be used again and need to be unnecessarily reloaded?
Link: https://lkml.kernel.org/r/20210104081631.2921415-1-lixinhai.lxh@gmail.com
Fixes: 75802ca663 ("mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible")
Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ef4c19d24 upstream.
syzbot found WARNINGs in several smackfs write operations where
bytes count is passed to memdup_user_nul which exceeds
GFP MAX_ORDER. Check count size if bigger than PAGE_SIZE.
Per smackfs doc, smk_write_net4addr accepts any label or -CIPSO,
smk_write_net6addr accepts any label or -DELETE. I couldn't find
any general rule for other label lengths except SMK_LABELLEN,
SMK_LONGLABEL, SMK_CIPSOMAX which are documented.
Let's constrain, in general, smackfs label lengths for PAGE_SIZE.
Although fuzzer crashes write to smackfs/netlabel on 0x400000 length.
Here is a quick way to reproduce the WARNING:
python -c "print('A' * 0x400000)" > /sys/fs/smackfs/netlabel
Reported-by: syzbot+a71a442385a0b2815497@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88a9e03bee upstream.
An assert failure is triggered by syzkaller test due to
ATTR_KILL_PRIV is not cleared before xfs_setattr_size.
As ATTR_KILL_PRIV is not checked/used by xfs_setattr_size,
just remove it from the assert.
Signed-off-by: Yumei Huang <yuhuang@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bef198f1b upstream.
syzbot is feeding invalid superblock data to JFS for mount testing.
JFS does not check several of the fields -- just assumes that they
are good since the JFS_MAGIC and version fields are good.
In this case (syzbot reproducer), we have s_l2bsize == 0xda0c,
pad == 0xf045, and s_state == 0x50, all of which are invalid IMO.
Having s_l2bsize == 0xda0c causes this UBSAN warning:
UBSAN: shift-out-of-bounds in fs/jfs/jfs_mount.c:373:25
shift exponent -9716 is negative
s_l2bsize can be tested for correctness. pad can be tested for non-0
and punted. s_state can be tested for its valid values and punted.
Do those 3 tests and if any of them fails, report the superblock as
invalid/corrupt and let fsck handle it.
With this patch, chkSuper() says this when JFS_DEBUG is enabled:
jfs_mount: Mount Failure: superblock is corrupt!
Mount JFS Failure: -22
jfs_mount failed w/return code = -22
The obvious problem with this method is that next week there could
be another syzbot test that uses different fields for invalid values,
this making this like a game of whack-a-mole.
syzkaller link: https://syzkaller.appspot.com/bug?extid=36315852ece4132ec193
Reported-by: syzbot+36315852ece4132ec193@syzkaller.appspotmail.com
Reported-by: kernel test robot <lkp@intel.com> # v2
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: jfs-discussion@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 580fa1b874 upstream.
The A64 ISA accepts distinct (but overlapping) ranges of immediates for:
* add arithmetic instructions ('I' machine constraint)
* sub arithmetic instructions ('J' machine constraint)
* 32-bit logical instructions ('K' machine constraint)
* 64-bit logical instructions ('L' machine constraint)
... but we currently use the 'I' constraint for many atomic operations
using sub or logical instructions, which is not always valid.
When CONFIG_ARM64_LSE_ATOMICS is not set, this allows invalid immediates
to be passed to instructions, potentially resulting in a build failure.
When CONFIG_ARM64_LSE_ATOMICS is selected the out-of-line ll/sc atomics
always use a register as they have no visibility of the value passed by
the caller.
This patch adds a constraint parameter to the ATOMIC_xx and
__CMPXCHG_CASE macros so that we can pass appropriate constraints for
each case, with uses updated accordingly.
Unfortunately prior to GCC 8.1.0 the 'K' constraint erroneously accepted
'4294967295', so we must instead force the use of a register.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
[bwh: Backported to 4.14: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4230509978 upstream.
The "L" AArch64 machine constraint, which we use for the "old" value in
an LL/SC cmpxchg(), generates an immediate that is suitable for a 64-bit
logical instruction. However, for cmpxchg() operations on types smaller
than 64 bits, this constraint can result in an invalid instruction which
is correctly rejected by GAS, such as EOR W1, W1, #0xffffffff.
Whilst we could special-case the constraint based on the cmpxchg size,
it's far easier to change the constraint to "K" and put up with using
a register for large 64-bit immediates. For out-of-line LL/SC atomics,
this is all moot anyway.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ef3fe4cec upstream.
Our atomic instructions (either LSE atomics of LDXR/STXR sequences)
natively support byte, half-word, word and double-word memory accesses
so there is no need to mask the data register prior to being stored.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5c6d0fcf9 upstream.
These plt* and .text.ftrace_trampoline sections specified for arm64 have
non-zero addressses. Non-zero section addresses in a relocatable ELF would
confuse GDB when it tries to compute the section offsets and it ends up
printing wrong symbol addresses. Therefore, set them to zero, which mirrors
the change in commit 5d8591bc0f ("module: set ksymtab/kcrctab* section
addresses to 0x0").
Reported-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210216183234.GA23876@amazon.com
Signed-off-by: Will Deacon <will@kernel.org>
[shaoyi@amazon.com: made same changes in arch/arm64/kernel/module.lds for 5.4]
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 182f709c5c upstream.
CCW_CMD_READ_STATUS was introduced with revision 2 of virtio-ccw,
and drivers should only rely on it being implemented when they
negotiated at least that revision with the device.
However, virtio_ccw_get_status() issued READ_STATUS for any
device operating at least at revision 1. If the device accepts
READ_STATUS regardless of the negotiated revision (which some
implementations like QEMU do, even though the spec currently does
not allow it), everything works as intended. While a device
rejecting the command should also be handled gracefully, we will
not be able to see any changes the device makes to the status,
such as setting NEEDS_RESET or setting the status to zero after
a completed reset.
We negotiated the revision to at most 1, as we never bumped the
maximum revision; let's do that now and properly send READ_STATUS
only if we are operating at least at revision 2.
Cc: stable@vger.kernel.org
Fixes: 7d3ce5ab94 ("virtio/s390: support READ_STATUS command for virtio-ccw")
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/20210216110645.1087321-1-cohuck@redhat.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cea4a7a18 upstream.
Otherwise build fails if the headers are not in the default location. While at
it also ask pkg-config for the libs, with fallback to the existing value.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2099b145d7 upstream.
In case of a system crash, dm-era might fail to mark blocks as written
in its metadata, although the corresponding writes to these blocks were
passed down to the origin device and completed successfully.
Consider the following sequence of events:
1. We write to a block that has not been yet written in the current era
2. era_map() checks the in-core bitmap for the current era and sees
that the block is not marked as written.
3. The write is deferred for submission after the metadata have been
updated and committed.
4. The worker thread processes the deferred write
(process_deferred_bios()) and marks the block as written in the
in-core bitmap, **before** committing the metadata.
5. The worker thread starts committing the metadata.
6. We do more writes that map to the same block as the write of step (1)
7. era_map() checks the in-core bitmap and sees that the block is marked
as written, **although the metadata have not been committed yet**.
8. These writes are passed down to the origin device immediately and the
device reports them as completed.
9. The system crashes, e.g., power failure, before the commit from step
(5) finishes.
When the system recovers and we query the dm-era target for the list of
written blocks it doesn't report the aforementioned block as written,
although the writes of step (6) completed successfully.
The issue is that era_map() decides whether to defer or not a write
based on non committed information. The root cause of the bug is that we
update the in-core bitmap, **before** committing the metadata.
Fix this by updating the in-core bitmap **after** successfully
committing the metadata.
Fixes: eec40579d8 ("dm: add era target")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee576c47db upstream.
The icmp{,v6}_send functions make all sorts of use of skb->cb, casting
it with IPCB or IP6CB, assuming the skb to have come directly from the
inet layer. But when the packet comes from the ndo layer, especially
when forwarded, there's no telling what might be in skb->cb at that
point. As a result, the icmp sending code risks reading bogus memory
contents, which can result in nasty stack overflows such as this one
reported by a user:
panic+0x108/0x2ea
__stack_chk_fail+0x14/0x20
__icmp_send+0x5bd/0x5c0
icmp_ndo_send+0x148/0x160
In icmp_send, skb->cb is cast with IPCB and an ip_options struct is read
from it. The optlen parameter there is of particular note, as it can
induce writes beyond bounds. There are quite a few ways that can happen
in __ip_options_echo. For example:
// sptr/skb are attacker-controlled skb bytes
sptr = skb_network_header(skb);
// dptr/dopt points to stack memory allocated by __icmp_send
dptr = dopt->__data;
// sopt is the corrupt skb->cb in question
if (sopt->rr) {
optlen = sptr[sopt->rr+1]; // corrupt skb->cb + skb->data
soffset = sptr[sopt->rr+2]; // corrupt skb->cb + skb->data
// this now writes potentially attacker-controlled data, over
// flowing the stack:
memcpy(dptr, sptr+sopt->rr, optlen);
}
In the icmpv6_send case, the story is similar, but not as dire, as only
IP6CB(skb)->iif and IP6CB(skb)->dsthao are used. The dsthao case is
worse than the iif case, but it is passed to ipv6_find_tlv, which does
a bit of bounds checking on the value.
This is easy to simulate by doing a `memset(skb->cb, 0x41,
sizeof(skb->cb));` before calling icmp{,v6}_ndo_send, and it's only by
good fortune and the rarity of icmp sending from that context that we've
avoided reports like this until now. For example, in KASAN:
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xa0e/0x12b0
Write of size 38 at addr ffff888006f1f80e by task ping/89
CPU: 2 PID: 89 Comm: ping Not tainted 5.10.0-rc7-debug+ #5
Call Trace:
dump_stack+0x9a/0xcc
print_address_description.constprop.0+0x1a/0x160
__kasan_report.cold+0x20/0x38
kasan_report+0x32/0x40
check_memory_region+0x145/0x1a0
memcpy+0x39/0x60
__ip_options_echo+0xa0e/0x12b0
__icmp_send+0x744/0x1700
Actually, out of the 4 drivers that do this, only gtp zeroed the cb for
the v4 case, while the rest did not. So this commit actually removes the
gtp-specific zeroing, while putting the code where it belongs in the
shared infrastructure of icmp{,v6}_ndo_send.
This commit fixes the issue by passing an empty IPCB or IP6CB along to
the functions that actually do the work. For the icmp_send, this was
already trivial, thanks to __icmp_send providing the plumbing function.
For icmpv6_send, this required a tiny bit of refactoring to make it
behave like the v4 case, after which it was straight forward.
Fixes: a2b78e9b2c ("sunvnet: generate ICMP PTMUD messages for smaller port MTUs")
Reported-by: SinYu <liuxyon@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CAF=yD-LOF116aHub6RMe8vB8ZpnrrnoTdqhobEx+bvoA8AsP0w@mail.gmail.com/T/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20210223131858.72082-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1faba27f11 upstream.
The W=1 compilation of allmodconfig generates the following warning:
net/ipv6/icmp.c:448:6: warning: no previous prototype for 'icmp6_send' [-Wmissing-prototypes]
448 | void icmp6_send(struct sk_buff *skb, u8 type, u8 code, __u32 info,
| ^~~~~~~~~~
Fix it by providing function declaration for builds with ipv6 as a module.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7a21b6fb upstream.
If IPv6 is builtin, we do not need an expensive indirect call
to reach icmp6_send().
v2: put inline keyword before the type to avoid sparse warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67c9a7e1e3 upstream.
Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0fce6f945 upstream.
Because gtp is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8e41f6033 upstream.
The icmpv6_send function has long had a static inline implementation
with an empty body for CONFIG_IPV6=n, so that code calling it doesn't
need to be ifdef'd. The new icmpv6_ndo_send function, which is intended
for drivers as a drop-in replacement with an identical function
signature, should follow the same pattern. Without this patch, drivers
that used to work with CONFIG_IPV6=n now result in a linker error.
Cc: Chen Zhou <chenzhou10@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0b41713b60 ("icmp: introduce helper for nat'd source address in network device context")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b41713b60 upstream.
This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cca2c6aebe upstream.
Metadata resize shouldn't happen in the ctr. The ctr loads a temporary
(inactive) table that will only become active upon resume. That is why
resize should always be done in terms of resume. Otherwise a load (ctr)
whose inactive table never becomes active will incorrectly resize the
metadata.
Also, perform the resize directly in preresume, instead of using the
worker to do it.
The worker might run other metadata operations, e.g., it could start
digestion, before resizing the metadata. These operations will end up
using the old size.
This could lead to errors, like:
device-mapper: era: metadata_digest_transcribe_writeset: dm_array_set_value failed
device-mapper: era: process_old_eras: digest step failed, stopping digestion
The reason of the above error is that the worker started the digestion
of the archived writeset using the old, larger size.
As a result, metadata_digest_transcribe_writeset tried to write beyond
the end of the era array.
Fixes: eec40579d8 ("dm: add era target")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2524933307 upstream.
In case of devices with at most 64 blocks, the digestion of consecutive
eras uses the writeset of the first era as the writeset of all eras to
digest, leading to lost writes. That is, we lose the information about
what blocks were written during the affected eras.
The digestion code uses a dm_disk_bitset object to access the archived
writesets. This structure includes a one word (64-bit) cache to reduce
the number of array lookups.
This structure is initialized only once, in metadata_digest_start(),
when we kick off digestion.
But, when we insert a new writeset into the writeset tree, before the
digestion of the previous writeset is done, or equivalently when there
are multiple writesets in the writeset tree to digest, then all these
writesets are digested using the same cache and the cache is not
re-initialized when moving from one writeset to the next.
For devices with more than 64 blocks, i.e., the size of the cache, the
cache is indirectly invalidated when we move to a next set of blocks, so
we avoid the bug.
But for devices with at most 64 blocks we end up using the same cached
data for digesting all archived writesets, i.e., the cache is loaded
when digesting the first writeset and it never gets reloaded, until the
digestion is done.
As a result, the writeset of the first era to digest is used as the
writeset of all the following archived eras, leading to lost writes.
Fix this by reinitializing the dm_disk_bitset structure, and thus
invalidating the cache, every time the digestion code starts digesting a
new writeset.
Fixes: eec40579d8 ("dm: add era target")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8e846ff93 upstream.
dm-era doesn't support changing the data block size of existing devices,
so check explicitly that the requested block size for a new target
matches the one stored in the metadata.
Fixes: eec40579d8 ("dm: add era target")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Reviewed-by: Ming-Hung Tsai <mtsai@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de89afc1e4 upstream.
Following a system crash, dm-era fails to recover the committed writeset
for the current era, leading to lost writes. That is, we lose the
information about what blocks were written during the affected era.
dm-era assumes that the writeset of the current era is archived when the
device is suspended. So, when resuming the device, it just moves on to
the next era, ignoring the committed writeset.
This assumption holds when the device is properly shut down. But, when
the system crashes, the code that suspends the target never runs, so the
writeset for the current era is not archived.
There are three issues that cause the committed writeset to get lost:
1. dm-era doesn't load the committed writeset when opening the metadata
2. The code that resizes the metadata wipes the information about the
committed writeset (assuming it was loaded at step 1)
3. era_preresume() starts a new era, without taking into account that
the current era might not have been archived, due to a system crash.
To fix this:
1. Load the committed writeset when opening the metadata
2. Fix the code that resizes the metadata to make sure it doesn't wipe
the loaded writeset
3. Fix era_preresume() to check for a loaded writeset and archive it,
before starting a new era.
Fixes: eec40579d8 ("dm: add era target")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78178ca844 upstream.
Patch fb6791d100 was designed to allow gfs2 to unmount quicker by
skipping the step where it tells dlm to unlock glocks in EX with lvbs.
This was done because when gfs2 unmounts a file system, it destroys the
dlm lockspace shortly after it destroys the glocks so it doesn't need to
unlock them all: the unlock is implied when the lockspace is destroyed
by dlm.
However, that patch introduced a use-after-free in dlm: as part of its
normal dlm_recoverd process, it can call ls_recovery to recover dead
locks. In so doing, it can call recover_rsbs which calls recover_lvb for
any mastered rsbs. Func recover_lvb runs through the list of lkbs queued
to the given rsb (if the glock is cached but unlocked, it will still be
queued to the lkb, but in NL--Unlocked--mode) and if it has an lvb,
copies it to the rsb, thus trying to preserve the lkb. However, when
gfs2 skips the dlm unlock step, it frees the glock and its lvb, which
means dlm's function recover_lvb references the now freed lvb pointer,
copying the freed lvb memory to the rsb.
This patch changes the check in gdlm_put_lock so that it calls
dlm_unlock for all glocks that contain an lvb pointer.
Fixes: fb6791d100 ("GFS2: skip dlm_unlock calls in unmount")
Cc: stable@vger.kernel.org # v3.8+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7780918b36 upstream.
Back in 2.1.29 the clear_user() guts (__bzero()) had been merged
with memset(). Unfortunately, while all exception handlers had been
copied, one of the exception table entries got lost. As the result,
clear_user() starting at 128*n bytes before the end of page and
spanning between 8 and 127 bytes into the next page would oops when
the second page is unmapped. It's trivial to reproduce - all
it takes is
main()
{
int fd = open("/dev/zero", O_RDONLY);
char *p = mmap(NULL, 16384, PROT_READ|PROT_WRITE,
MAP_PRIVATE|MAP_ANON, -1, 0);
munmap(p + 8192, 8192);
read(fd, p + 8192 - 128, 192);
}
which had been oopsing since March 1997. Says something about
the quality of test coverage... ;-/ And while today sparc32 port
is nearly dead, back in '97 it had been very much alive; in fact,
sparc64 had only been in mainline for 3 months by that point...
Cc: stable@kernel.org
Fixes: v2.1.29
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a8109f303 upstream.
printk_safe_flush_on_panic() caused the following deadlock on our
server:
CPU0: CPU1:
panic rcu_dump_cpu_stacks
kdump_nmi_shootdown_cpus nmi_trigger_cpumask_backtrace
register_nmi_handler(crash_nmi_callback) printk_safe_flush
__printk_safe_flush
raw_spin_lock_irqsave(&read_lock)
// send NMI to other processors
apic_send_IPI_allbutself(NMI_VECTOR)
// NMI interrupt, dead loop
crash_nmi_callback
printk_safe_flush_on_panic
printk_safe_flush
__printk_safe_flush
// deadlock
raw_spin_lock_irqsave(&read_lock)
DEADLOCK: read_lock is taken on CPU1 and will never get released.
It happens when panic() stops a CPU by NMI while it has been in
the middle of printk_safe_flush().
Handle the lock the same way as logbuf_lock. The printk_safe buffers
are flushed only when both locks can be safely taken. It can avoid
the deadlock _in this particular case_ at expense of losing contents
of printk_safe buffers.
Note: It would actually be safe to re-init the locks when all CPUs were
stopped by NMI. But it would require passing this information
from arch-specific code. It is not worth the complexity.
Especially because logbuf_lock and printk_safe buffers have been
obsoleted by the lockless ring buffer.
Fixes: cf9b1106c8 ("printk/nmi: flush NMI messages on the system panic")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: <stable@vger.kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210210034823.64867-1-songmuchun@bytedance.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8002a3593 upstream.
If no n_latch value will be provided at driver probe then all pins will
be used as an input:
gpio->out = ~n_latch;
In that case initial state for all pins is "one":
gpio->status = gpio->out;
So if pcf857x IRQ happens with change pin value from "zero" to "one"
then we miss it, because of "one" from IRQ and "one" from initial state
leaves corresponding pin unchanged:
change = (gpio->status ^ status) & gpio->irq_enabled;
The right solution will be to read actual state at driver probe.
Cc: stable@vger.kernel.org
Fixes: 6e20a0a429 ("gpio: pcf857x: enable gpio_to_irq() support")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebfac7b778 upstream.
clang-12 -fno-pic (since
a084c0388e)
can emit `call __stack_chk_fail@PLT` instead of `call __stack_chk_fail`
on x86. The two forms should have identical behaviors on x86-64 but the
former causes GNU as<2.37 to produce an unreferenced undefined symbol
_GLOBAL_OFFSET_TABLE_.
(On x86-32, there is an R_386_PC32 vs R_386_PLT32 difference but the
linker behavior is identical as far as Linux kernel is concerned.)
Simply ignore _GLOBAL_OFFSET_TABLE_ for now, like what
scripts/mod/modpost.c:ignore_undef_symbol does. This also fixes the
problem for gcc/clang -fpie and -fpic, which may emit `call foo@PLT` for
external function calls on x86.
Note: ld -z defs and dynamic loaders do not error for unreferenced
undefined symbols so the module loader is reading too much. If we ever
need to ignore more symbols, the code should be refactored to ignore
unreferenced symbols.
Cc: <stable@vger.kernel.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/1250
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=27178
Reported-by: Marco Elver <elver@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Marco Elver <elver@google.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7018c897c2 upstream
Richard reports that the following test:
(while true; do
cat /sys/bus/nd/devices/nmem*/available_slots 2>&1 > /dev/null
done) &
while true; do
for i in $(seq 0 4); do
echo nmem$i > /sys/bus/nd/drivers/nvdimm/bind
done
for i in $(seq 0 4); do
echo nmem$i > /sys/bus/nd/drivers/nvdimm/unbind
done
done
...fails with a crash signature like:
divide error: 0000 [#1] SMP KASAN PTI
RIP: 0010:nd_label_nfree+0x134/0x1a0 [libnvdimm]
[..]
Call Trace:
available_slots_show+0x4e/0x120 [libnvdimm]
dev_attr_show+0x42/0x80
? memset+0x20/0x40
sysfs_kf_seq_show+0x218/0x410
The root cause is that available_slots_show() consults driver-data, but
fails to synchronize against device-unbind setting up a TOCTOU race to
access uninitialized memory.
Validate driver-data under the device-lock.
Fixes: 4d88a97aa9 ("libnvdimm, nvdimm: dimm driver and base libnvdimm device-driver infrastructure")
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Coly Li <colyli@suse.com>
Reported-by: Richard Palethorpe <rpalethorpe@suse.com>
Acked-by: Richard Palethorpe <rpalethorpe@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[sudip: use device_lock()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ffddd499b upstream
There is a race condition between __free_huge_page()
and dissolve_free_huge_page().
CPU0: CPU1:
// page_count(page) == 1
put_page(page)
__free_huge_page(page)
dissolve_free_huge_page(page)
spin_lock(&hugetlb_lock)
// PageHuge(page) && !page_count(page)
update_and_free_page(page)
// page is freed to the buddy
spin_unlock(&hugetlb_lock)
spin_lock(&hugetlb_lock)
clear_page_huge_active(page)
enqueue_huge_page(page)
// It is wrong, the page is already freed
spin_unlock(&hugetlb_lock)
The race window is between put_page() and dissolve_free_huge_page().
We should make sure that the page is already on the free list when it is
dissolved.
As a result __free_huge_page would corrupt page(s) already in the buddy
allocator.
Link: https://lkml.kernel.org/r/20210115124942.46403-4-songmuchun@bytedance.com
Fixes: c8721bbbdd ("mm: memory-hotplug: enable memory hotplug to handle hugepage")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3272cfc252 upstream.
page structs are not guaranteed to be contiguous for gigantic pages. The
routine copy_huge_page_from_user can encounter gigantic pages, yet it
assumes page structs are contiguous when copying pages from user space.
Since page structs for the target gigantic page are not contiguous, the
data copied from user space could overwrite other pages not associated
with the gigantic page and cause data corruption.
Non-contiguous page structs are generally not an issue. However, they can
exist with a specific kernel configuration and hotplug operations. For
example: Configure the kernel with CONFIG_SPARSEMEM and
!CONFIG_SPARSEMEM_VMEMMAP. Then, hotplug add memory for the area where
the gigantic page will be allocated.
Link: https://lkml.kernel.org/r/20210217184926.33567-2-mike.kravetz@oracle.com
Fixes: 8fb5debc5f ("userfaultfd: hugetlbfs: add hugetlb_mcopy_atomic_pte for userfaultfd support")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Joao Martins <joao.m.martins@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 740c0a57b8 upstream.
The MEI bus has a special behavior on suspend it destroys
all the attached devices, this is due to the fact that also
firmware context is not persistent across power flows.
If watchdog on MEI bus is ticking before suspending the firmware
times out and reports that the OS is missing watchdog tick.
Send the stop command to the firmware on watchdog unregistered
to eliminate the false event on suspend.
This does not make the things worse from the user-space perspective
as a user-space should re-open watchdog device after
suspending before this patch.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210124114938.373885-1-tomas.winkler@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0c014cd2 upstream.
This issue was originally fixed in 09954bad4 ("floppy: refactor open()
flags handling").
The fix as a side-effect, however, introduce issue for open(O_ACCMODE)
that is being used for ioctl-only open. I wrote a fix for that, but
instead of it being merged, full revert of 09954bad4 was performed,
re-introducing the O_NDELAY / O_NONBLOCK issue, and it strikes again.
This is a forward-port of the original fix to current codebase; the
original submission had the changelog below:
====
Commit 09954bad4 ("floppy: refactor open() flags handling"), as a
side-effect, causes open(/dev/fdX, O_ACCMODE) to fail. It turns out that
this is being used setfdprm userspace for ioctl-only open().
Reintroduce back the original behavior wrt !(FMODE_READ|FMODE_WRITE)
modes, while still keeping the original O_NDELAY bug fixed.
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2101221209060.5622@cbobk.fhfr.pm
Cc: stable@vger.kernel.org
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Reported-and-tested-by: Kurt Garloff <kurt@garloff.de>
Fixes: 09954bad4 ("floppy: refactor open() flags handling")
Fixes: f2791e7ead ("Revert "floppy: refactor open() flags handling"")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed72736183 upstream.
Force all CPUs to do VMXOFF (via NMI shootdown) during an emergency
reboot if VMX is _supported_, as VMX being off on the current CPU does
not prevent other CPUs from being in VMX root (post-VMXON). This fixes
a bug where a crash/panic reboot could leave other CPUs in VMX root and
prevent them from being woken via INIT-SIPI-SIPI in the new kernel.
Fixes: d176720d34 ("x86: disable VMX on all CPUs on reboot")
Cc: stable@vger.kernel.org
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: David P. Reed <dpreed@deepplum.com>
[sean: reworked changelog and further tweaked comment]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201231002702.2223707-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bdcd851fa upstream.
The optimized cipher function need length multiple of 4 bytes.
But it get sometimes odd length.
This is due to SG data could be stored with an offset.
So the fix is to check also if the offset is aligned with 4 bytes.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Cc: <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72c9925f87 upstream.
At btrfs_copy_root(), if the call to btrfs_inc_ref() fails we end up
returning without unlocking and releasing our reference on the extent
buffer named "cow" we previously allocated with btrfs_alloc_tree_block().
So fix that by unlocking the extent buffer and dropping our reference on
it before returning.
Fixes: be20aa9dba ("Btrfs: Add mount option to turn off data cow")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78a10aebb upstream.
When recovering a relocation, if we run into a reloc root that has 0
refs we simply add it to the reloc_control->reloc_roots list, and then
clean it up later. The problem with this is __del_reloc_root() doesn't
do anything if the root isn't in the radix tree, which in this case it
won't be because we never call __add_reloc_root() on the reloc_root.
This exit condition simply isn't correct really. During normal
operation we can remove ourselves from the rb tree and then we're meant
to clean up later at merge_reloc_roots() time, and this happens
correctly. During recovery we're depending on free_reloc_roots() to
drop our references, but we're short-circuiting.
Fix this by continuing to check if we're on the list and dropping
ourselves from the reloc_control root list and dropping our reference
appropriately. Change the corresponding BUG_ON() to an ASSERT() that
does the correct thing if we aren't in the rb tree.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 867ed321f9 upstream.
While testing my error handling patches, I added a error injection site
at btrfs_inc_extent_ref, to validate the error handling I added was
doing the correct thing. However I hit a pretty ugly corruption while
doing this check, with the following error injection stack trace:
btrfs_inc_extent_ref
btrfs_copy_root
create_reloc_root
btrfs_init_reloc_root
btrfs_record_root_in_trans
btrfs_start_transaction
btrfs_update_inode
btrfs_update_time
touch_atime
file_accessed
btrfs_file_mmap
This is because we do not catch the error from btrfs_inc_extent_ref,
which in practice would be ENOMEM, which means we lose the extent
references for a root that has already been allocated and inserted,
which is the problem. Fix this by aborting the transaction if we fail
to do the reference modification.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8da7520c80 upstream.
Consider the following transcript:
$ keyctl add trusted kmk "new 32 blobauth=helloworld keyhandle=80000000 migratable=1" @u
add_key: Invalid argument
The documentation has the following description:
migratable= 0|1 indicating permission to reseal to new PCR values,
default 1 (resealing allowed)
The consequence is that "migratable=1" should succeed. Fix this by
allowing this condition to pass instead of return -EINVAL.
[*] Documentation/security/keys/trusted-encrypted.rst
Cc: stable@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Fixes: d00a1c72f7 ("keys: add new trusted key-type")
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d9ae54af1 upstream.
The TPM TIS specification says the TPM signals the acquisition of locality
when the TMP_ACCESS_REQUEST_USE bit goes to one *and* the
TPM_ACCESS_REQUEST_USE bit goes to zero. Currently we only check the
former not the latter, so check both. Adding the check on
TPM_ACCESS_REQUEST_USE should fix the case where the locality is
re-requested before the TPM has released it. In this case the locality may
get released briefly before it is reacquired, which causes all sorts of
problems. However, with the added check, TPM_ACCESS_REQUEST_USE should
remain 1 until the second request for the locality is granted.
Cc: stable@ger.kernel.org
Fixes: 27084efee0 ("[PATCH] tpm: driver for next generation TPM chips")
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eaa1a3714 upstream.
musb_queue_resume_work() would call the provided callback if the runtime
PM status was 'active'. Otherwise, it would enqueue the request if the
hardware was still suspended (musb->is_runtime_suspended is true).
This causes a race with the runtime PM handlers, as it is possible to be
in the case where the runtime PM status is not yet 'active', but the
hardware has been awaken (PM resume function has been called).
When hitting the race, the resume work was not enqueued, which probably
triggered other bugs further down the stack. For instance, a telnet
connection on Ingenic SoCs would result in a 50/50 chance of a
segmentation fault somewhere in the musb code.
Rework the code so that either we call the callback directly if
(musb->is_runtime_suspended == 0), or enqueue the query otherwise.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: stable@vger.kernel.org # v4.9+
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210123142502.16980-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d6e7ab7f upstream.
After commit 77b425399f ("Input: i8042 - use chassis info to skip
selftest on Asus laptops"), all modern Asus laptops have the i8042
selftest disabled. It has done by using chassys type "10" (laptop).
The Asus Zenbook Flip suffers from similar suspend/resume issues, but
it _sometimes_ work and sometimes it doesn't. Setting noselftest makes
it work reliably. In this case, we need to add chassis type "31"
(convertible) in order to avoid selftest in this device.
Reported-by: Ludvig Norgren Guldhag <ludvigng@gmail.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210219164638.761-1-mpdesouza@suse.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88f38846bf upstream.
The `wacom_feature_mapping` function is careful to only set the the
touch_max value a single time, but this care does not extend to the
`wacom_wac_finger_event` function. In particular, if a device sends
multiple HID_DG_CONTACTMAX items in a single feature report, the
driver will end up retaining the value of last item.
The HID descriptor for the Cintiq Companion 2 does exactly this. It
incorrectly sets a "Report Count" of 2, which will cause the driver
to process two HID_DG_CONTACTCOUNT items. The first item has the actual
count, while the second item should have been declared as a constant
zero. The constant zero is the value the driver ends up using, however,
since it is the last HID_DG_CONTACTCOUNT in the report.
Report ID (16),
Usage (Contact Count Maximum), ; Contact count maximum (55h, static value)
Report Count (2),
Logical Maximum (10),
Feature (Variable),
To address this, we add a check that the touch_max is not already set
within the `wacom_wac_finger_event` function that processes the
HID_DG_TOUCHMAX item. We emit a warning if the value is set and ignore
the updated value.
This could potentially cause problems if there is a tablet which has
a similar issue but requires the last item to be used. This is unlikely,
however, since it would have to have a different non-zero value for
HID_DG_CONTACTMAX earlier in the same report, which makes no sense
except in the case of a firmware bug. Note that cases where the
HID_DG_CONTACTMAX items are in different reports is already handled
(and similarly ignored) by `wacom_feature_mapping` as mentioned above.
Link: https://github.com/linuxwacom/input-wacom/issues/223
Fixes: 184eccd403 ("HID: wacom: generic: read HID_DG_CONTACTMAX from any feature report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67e40054de upstream.
A list_add corruption is reported by Hulk Robot like this:
==============
list_add corruption.
Call Trace:
link_obj+0xc0/0x1c0
link_group+0x21/0x140
configfs_register_subsystem+0xdb/0x380
acpi_configfs_init+0x25/0x1000 [acpi_configfs]
do_one_initcall+0x149/0x820
do_init_module+0x1ef/0x720
load_module+0x35c8/0x4380
__do_sys_finit_module+0x10d/0x1a0
do_syscall_64+0x34/0x80
It's because of the missing check after configfs_register_default_group,
where configfs_unregister_subsystem should be called once failure.
Fixes: 612bd01fc6 ("ACPI: add support for loading SSDTs via configfs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1e6bd2995 upstream.
Property matching does not work for ACPI fwnodes if the value of the
given property is not represented as a package in the _DSD package
containing it. For example, the "compatible" property in the _DSD
below
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"compatible", "ethernet-phy-ieee802.3-c45"}
}
})
will not be found by fwnode_property_match_string(), because the ACPI
code handling device properties does not regard the single value as a
"list" in that case.
Namely, fwnode_property_match_string() invoked to match a given
string property value first calls fwnode_property_read_string_array()
with the last two arguments equal to NULL and 0, respectively, in
order to count the items in the value of the given property, with the
assumption that this value may be an array. For ACPI fwnodes, that
operation is carried out by acpi_node_prop_read() which calls
acpi_data_prop_read() for this purpose. However, when the return
(val) pointer is NULL, that function only looks for a property whose
value is a package without checking the single-value case at all.
To fix that, make acpi_data_prop_read() check the single-value
case if its return pointer argument is NULL and modify
acpi_data_prop_read_single() handling that case to attempt to
read the value of the property if the return pointer is NULL
and return 1 if that succeeds.
Fixes: 3708184afc ("device property: Move FW type specific functionality to FW specific files")
Reported-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97f433c360 upstream.
We get I/O errors when we run md-raid1 on the top of dm-integrity on the
top of ramdisk.
device-mapper: integrity: Bio not aligned on 8 sectors: 0xff00, 0xff
device-mapper: integrity: Bio not aligned on 8 sectors: 0xff00, 0xff
device-mapper: integrity: Bio not aligned on 8 sectors: 0xffff, 0x1
device-mapper: integrity: Bio not aligned on 8 sectors: 0xffff, 0x1
device-mapper: integrity: Bio not aligned on 8 sectors: 0x8048, 0xff
device-mapper: integrity: Bio not aligned on 8 sectors: 0x8147, 0xff
device-mapper: integrity: Bio not aligned on 8 sectors: 0x8246, 0xff
device-mapper: integrity: Bio not aligned on 8 sectors: 0x8345, 0xbb
The ramdisk device has logical_block_size 512 and max_sectors 255. The
dm-integrity device uses logical_block_size 4096 and it doesn't affect the
"max_sectors" value - thus, it inherits 255 from the ramdisk. So, we have
a device with max_sectors not aligned on logical_block_size.
The md-raid device sees that the underlying leg has max_sectors 255 and it
will split the bios on 255-sector boundary, making the bios unaligned on
logical_block_size.
In order to fix the bug, we round down max_sectors to logical_block_size.
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1858ce0cf ]
The brcmstb_send_i2c_cmd currently has a condition that is (CMD_RD ||
CMD_WR) which always evaluates to true, while the obvious fix is to test
whether the cmd variable passed as parameter holds one of these two
values.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d41053e8d ]
Although there has been a bit of back and forth on the subject, it
appears that invalidating TLBs requires an ISB instruction when FEAT_ETS
is not implemented by the CPU.
From the bible:
| In an implementation that does not implement FEAT_ETS, a TLB
| maintenance instruction executed by a PE, PEx, can complete at any
| time after it is issued, but is only guaranteed to be finished for a
| PE, PEx, after the execution of DSB by the PEx followed by a Context
| synchronization event
Add the missing ISB in __primary_switch, just in case.
Fixes: 3c5e9f238b ("arm64: head.S: move KASLR processing out of __enable_mmu()")
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210224093738.3629662-3-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c6058024 ]
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with I40E_TX_CTX_EXT_IP_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a3fd9d8876 ("i40e/i40evf: Handle IPv6 extension headers in checksum offload")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5776e7524 ]
In the case where we need to do an interior node split, and
immediately afterwards, we are unable to allocate a new directory leaf
block due to ENOSPC, the directory index checksum's will not be filled
in correctly (and indeed, will not be correctly journalled).
This looks like a bug that was introduced when we added largedir
support. The original code doesn't make any sense (and should have
been caught in code review), but it was hidden because most of the
time, the index node checksum will be set by do_split(). But if
do_split bails out due to ENOSPC, then ext4_handle_dirty_dx_node()
won't get called, and so the directory index checksum field will not
get set, leading to:
EXT4-fs error (device sdb): dx_probe:858: inode #6635543: block 4022: comm nfsd: Directory index failed checksum
Google-Bug-Id: 176345532
Fixes: e08ac99fa2 ("ext4: add largedir feature")
Cc: Artem Blagodarenko <artem.blagodarenko@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33a7808ce1 ]
The previous registers were *almost* correct, but instead of
PHYs, they were pointing at DSI PLLs, resulting in the PHY id
autodetection failing miserably.
Fixes: dcefc117cc ("drm/msm/dsi: Add support for msm8x94")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef9e4005cb ]
After 34e3207205 ("PCI: handle positive error codes"),
pci_user_read_config_*() and pci_user_write_config_*() return 0 or negative
errno values, not PCIBIOS_* values like PCIBIOS_SUCCESSFUL or
PCIBIOS_BAD_REGISTER_NUMBER.
Remove comparisons with PCIBIOS_SUCCESSFUL and check only for non-zero. It
happens that PCIBIOS_SUCCESSFUL is zero, so this is not a functional
change, but it aligns this code with the user accessors.
[bhelgaas: commit log]
Fixes: 34e3207205 ("PCI: handle positive error codes")
Link: https://lore.kernel.org/r/f1220314-e518-1e18-bf94-8e6f8c703758@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a16c53540 ]
When the VMCI host support releases guest memory in the case where
the VM was killed, the pinned guest pages aren't locked. Use
set_page_dirty_lock() instead of set_page_dirty().
Testing done: Killed VM while having an active VMCI based vSocket
connection and observed warning from ext4. With this fix, no
warning was observed. Ran various vSocket tests without issues.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/1611160360-30299-1-git-send-email-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5d8d67586 ]
If rockchip_pwm_probe() fails to register a PWM device it calls
clk_unprepare() for the device's PWM clock, without having first disabled
the clock and before jumping to an error handler that also unprepares
it. This is likely to produce warnings from the kernel about the clock
being unprepared when it is still enabled, and then being unprepared when
it has already been unprepared.
Prevent these warnings by removing this unnecessary call to
clk_unprepare().
Fixes: 48cf973cae ("pwm: rockchip: Avoid glitches on already running PWMs")
Signed-off-by: Simon South <simon@simonsouth.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80bddf5c93 ]
Currently COMPAT on SPARC64 selects COMPAT_BINFMT_ELF unconditionally,
even when BINFMT_ELF is not enabled. This causes a kconfig warning.
Instead, just select COMPAT_BINFMT_ELF if BINFMT_ELF is enabled.
This builds cleanly with no kconfig warnings.
WARNING: unmet direct dependencies detected for COMPAT_BINFMT_ELF
Depends on [n]: COMPAT [=y] && BINFMT_ELF [=n]
Selected by [y]:
- COMPAT [=y] && SPARC64 [=y]
Fixes: 26b4c91218 ("sparc,sparc64: unify Kconfig files")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5c97cadd7 ]
The ubsan reported the following error. It was because sample's raw
data missed u32 padding at the end. So it broke the alignment of the
array after it.
The raw data contains an u32 size prefix so the data size should have
an u32 padding after 8-byte aligned data.
27: Sample parsing :util/synthetic-events.c:1539:4:
runtime error: store to misaligned address 0x62100006b9bc for type
'__u64' (aka 'unsigned long long'), which requires 8 byte alignment
0x62100006b9bc: note: pointer points here
00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
#0 0x561532a9fc96 in perf_event__synthesize_sample util/synthetic-events.c:1539:13
#1 0x5615327f4a4f in do_test tests/sample-parsing.c:284:8
#2 0x5615327f3f50 in test__sample_parsing tests/sample-parsing.c:381:9
#3 0x56153279d3a1 in run_test tests/builtin-test.c:424:9
#4 0x56153279c836 in test_and_print tests/builtin-test.c:454:9
#5 0x56153279b7eb in __cmd_test tests/builtin-test.c:675:4
#6 0x56153279abf0 in cmd_test tests/builtin-test.c:821:9
#7 0x56153264e796 in run_builtin perf.c:312:11
#8 0x56153264cf03 in handle_internal_command perf.c:364:8
#9 0x56153264e47d in run_argv perf.c:408:2
#10 0x56153264c9a9 in main perf.c:538:3
#11 0x7f137ab6fbbc in __libc_start_main (/lib64/libc.so.6+0x38bbc)
#12 0x561532596828 in _start ...
SUMMARY: UndefinedBehaviorSanitizer: misaligned-pointer-use
util/synthetic-events.c:1539:4 in
Fixes: 045f8cd854 ("perf tests: Add a sample parsing test")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210214091638.519643-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 768d70e19b ]
dlpar_configure_connector() has two problems in its handling of
ibm,configure-connector's return status:
1. When the status is -2 (busy, call again), we call
ibm,configure-connector again immediately without checking whether
to schedule, which can result in monopolizing the CPU.
2. Extended delay status (9900..9905) goes completely unhandled,
causing the configuration to unnecessarily terminate.
Fix both of these issues by using rtas_busy_delay().
Fixes: ab519a011c ("powerpc/pseries: Kernel DLPAR Infrastructure")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210107025900.410369-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26783d74cc ]
The "req" struct is always added to the "wm831x->auxadc_pending" list,
but it's only removed from the list on the success path. If a failure
occurs then the "req" struct is freed but it's still on the list,
leading to a use after free.
Fixes: 78bb3688ea ("mfd: Support multiple active WM831x AUXADC conversions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de5d7adb89 ]
Consider an amba driver with a .probe but without a .remove callback (e.g.
pl061_gpio_driver). The function amba_probe() is called to bind a device
and so dev_pm_domain_attach() and others are called. As there is no remove
callback amba_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use the core driver callbacks and handle missing amba
callbacks there. For probe refuse registration as a driver without probe
doesn't make sense.
Fixes: 7cfe249475 ("ARM: AMBA: Add pclk support to AMBA bus infrastructure")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210126165835.687514-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2acb909750 ]
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fc5461823 ]
MAD message received by the user has EINVAL error in all flows
including when the device is disassociated. That makes it impossible
for the applications to treat such flow differently.
Change it to return EIO, so the applications will be able to perform
disassociation recovery.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20210125121339.837518-2-leon@kernel.org
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89b0a4267 ]
Drop the call to msecs_to_jiffies(), as "HZ / fbdev->refresh_rate" is
already the number of jiffies to wait.
Fixes: 8992da44c6 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4993e1f947 ]
KEY_FLAG_KEEP is not meant to be passed to keyring_alloc() or key_alloc(),
as these only take KEY_ALLOC_* flags. KEY_FLAG_KEEP has the same value as
KEY_ALLOC_BYPASS_RESTRICTION, but fortunately only key_create_or_update()
uses it. LSMs using the key_alloc hook don't check that flag.
KEY_FLAG_KEEP is then ignored but fortunately (again) the root user cannot
write to the blacklist keyring, so it is not possible to remove a key/hash
from it.
Fix this by adding a KEY_ALLOC_SET_KEEP flag that tells key_alloc() to set
KEY_FLAG_KEEP on the new key. blacklist_init() can then, correctly, pass
this to keyring_alloc().
We can also use this in ima_mok_init() rather than setting the flag
manually.
Note that this doesn't fix an observable bug with the current
implementation but it is required to allow addition of new hashes to the
blacklist in the future without making it possible for them to be removed.
Fixes: 734114f878 ("KEYS: Add a system blacklist keyring")
Reported-by: Mickaël Salaün <mic@linux.microsoft.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Mickaël Salaün <mic@linux.microsoft.com>
cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a5a75e5e9 ]
If the device tree is incorrectly configured, and attempts to
define a "no-map" reserved memory that overlaps with the kernel
data/code, the kernel would crash quickly after boot, with no
obvious clue about the nature of the issue.
For example, this would happen if we have the kernel mapped at
these addresses (from /proc/iomem):
40000000-41ffffff : System RAM
40080000-40dfffff : Kernel code
40e00000-411fffff : reserved
41200000-413e0fff : Kernel data
And we declare a no-map shared-dma-pool region at a fixed address
within that range:
mem_reserved: mem_region {
compatible = "shared-dma-pool";
reg = <0 0x40000000 0 0x01A00000>;
no-map;
};
To fix this, when removing memory regions at early boot (which is
what "no-map" regions do), we need to make sure that the memory
is not already reserved. If we do, __reserved_mem_reserve_reg
will throw an error:
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory
for node 'mem_region': base 0x0000000040000000, size 26 MiB
and the code that will try to use the region should also fail,
later on.
We do not do anything for non-"no-map" regions, as memblock
explicitly allows reserved regions to overlap, and the commit
that this fixes removed the check for that precise reason.
[ qperret: fixed conflicts caused by the usage of memblock_mark_nomap ]
Fixes: 094cb98179 ("of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20210115114544.1830068-3-qperret@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 035b73b2b3 ]
On Intel Tangier B0 and Anniedale the interrupt line, disregarding
to have different numbers, is shared between HSU DMA and UART IPs.
Thus on such SoCs we are expecting that IRQ handler is called in
UART driver only. hsu_pci_irq was handling the spurious interrupt
from HSU DMA by returning immediately. This wastes CPU time and
since HSU DMA and HSU UART interrupt occur simultaneously they race
to be handled causing delay to the HSU UART interrupt handling.
Fix this by disabling the interrupt entirely.
Fixes: 4831e0d905 ("serial: 8250_mid: handle interrupt correctly in DMA case")
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210112223749.97036-1-ftoth@exalondelft.nl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbc0ad004c ]
A 'irq_dispose_mapping()' call is missing in the remove function.
Add it.
This is needed to undo the 'irq_of_parse_and_map() call from the probe
function and already part of the error handling path of the probe function.
It was added in the probe function only in commit d3f620b2c4 ("fsldma:
simplify IRQ probing and handling")
Fixes: 77cd62e808 ("fsldma: allow Freescale Elo DMA driver to be compiled as a module")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201212160516.92515-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0312af1f9 ]
Prevent invalid (0, 0) inputs to hid-core's snto32() function.
Maybe it is just the dummy device here that is causing this, but
there are hundreds of calls to snto32(0, 0). Having n (bits count)
of 0 is causing the current UBSAN trap with a shift value of
0xffffffff (-1, or n - 1 in this function).
Either of the value to shift being 0 or the bits count being 0 can be
handled by just returning 0 to the caller, avoiding the following
complex shift + OR operations:
return value & (1 << (n - 1)) ? value | (~0U << n) : value;
Fixes: dde5845a52 ("[PATCH] Generic HID layer - code split")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+1e911ad71dd4ea72e04a@syzkaller.appspotmail.com
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceeda328ed ]
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ebabde38 ]
The v3 file capabilities have a uid field that records the filesystem
uid of the root user of the user namespace the file capabilities are
valid in.
When someone is silly enough to have the same underlying uid as the
root uid of multiple nested containers a v3 filesystem capability can
be ambiguous.
In the spirit of don't do that then, forbid writing a v3 filesystem
capability if it is ambiguous.
Fixes: 8db6c34f1d ("Introduce v3 namespaced file capabilities")
Reviewed-by: Andrew G. Morgan <morgan@kernel.org>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19646447ad ]
clang static analysis reports this problem
fs/jffs2/summary.c:794:31: warning: Use of memory after it is freed
c->summary->sum_list_head = temp->u.next;
^~~~~~~~~~~~
In jffs2_sum_write_data(), in a loop summary data is handles a node at
a time. When it has written out the node it is removed the summary list,
and the node is deleted. In the corner case when a
JFFS2_FEATURE_RWCOMPAT_COPY is seen, a call is made to
jffs2_sum_disable_collecting(). jffs2_sum_disable_collecting() deletes
the whole list which conflicts with the loop's deleting the list by parts.
To preserve the old behavior of stopping the write midway, bail out of
the loop after disabling summary collection.
Fixes: 6171586a7a ("[JFFS2] Correct handling of JFFS2_FEATURE_RWCOMPAT_COPY nodes.")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4208c398aa ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit integer. In the case where
l2nb is 32 or more this can lead to an overflow. Avoid this by shifting
the value 1LL instead.
Addresses-Coverity: ("Uninitentional integer overflow")
Fixes: b40c2e665c ("fs/jfs: TRIM support for JFS Filesystem")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31e3386a4 ]
IMA allocates kernel virtual memory to carry forward the measurement
list, from the current kernel to the next kernel on kexec system call,
in ima_add_kexec_buffer() function. This buffer is not freed before
completing the kexec system call resulting in memory leak.
Add ima_buffer field in "struct kimage" to store the virtual address
of the buffer allocated for the IMA measurement list.
Free the memory allocated for the IMA measurement list in
kimage_file_post_load_cleanup() function.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Suggested-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Fixes: 7b8589cc29 ("ima: on soft reboot, save the measurement list")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d14c65178 ]
IMA allocates kernel virtual memory to carry forward the measurement
list, from the current kernel to the next kernel on kexec system call,
in ima_add_kexec_buffer() function. In error code paths this memory
is not freed resulting in memory leak.
Free the memory allocated for the IMA measurement list in
the error code paths in ima_add_kexec_buffer() function.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Suggested-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Fixes: 7b8589cc29 ("ima: on soft reboot, save the measurement list")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a53ab94eb6 ]
The length ('len' parameter) passed to crypto_ecdh_decode_key() is never
checked against the length encoded in the passed buffer ('buf'
parameter). This could lead to an out-of-bounds access when the passed
length is less than the encoded length.
Add a check to prevent that.
Fixes: 3c4b23901a ("crypto: ecdh - Add ECDH software support")
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cc64e7ebf ]
Return value in __load_free_space_cache is not properly set after
(unlikely) memory allocation failures and 0 is returned instead.
This is not a problem for the caller load_free_space_cache because only
value 1 is considered as 'cache loaded' but for clarity it's better
to set the errors accordingly.
Fixes: a67509c300 ("Btrfs: add a io_ctl struct and helpers for dealing with the space cache")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3fa4b747f ]
When channel->device_obj is non-NULL, vmbus_onoffer_rescind() could
invoke put_device(), that will eventually release the device and free
the channel object (cf. vmbus_device_release()). However, a pointer
to the object is dereferenced again later to load the primary_channel.
The use-after-free can be avoided by noticing that this load/check is
redundant if device_obj is non-NULL: primary_channel must be NULL if
device_obj is non-NULL, cf. vmbus_add_channel_work().
Fixes: 54a66265d6 ("Drivers: hv: vmbus: Fix rescind handling")
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20201209070827.29335-5-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10340f8d7b ]
While reworking the resources management and departing from using
ahci_platform_enable_resources() which did not allow a proper step
separation like we need, we unfortunately lost the ability to control
AHCI regulators. This broke some Broadcom STB systems that do expect
regulators to be turned on to link up with attached hard drives.
Fixes: c0cdf2ac4b ("ata: ahci_brcm: Fix AHCI resources management")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9455ffae ]
The Renkforce RF AC4K 300 Action Cam 4K reports invalid bFormatIndex and
bFrameIndex values when negotiating the video probe and commit controls.
The UVC descriptors report a single supported format and frame size,
with bFormatIndex and bFrameIndex both equal to 2, but the video probe
and commit controls report bFormatIndex and bFrameIndex set to 1.
The device otherwise operates correctly, but the driver rejects the
values and fails the format try operation. Fix it by ignoring the
invalid indices, and assuming that the format and frame requested by the
driver are accepted by the device.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210767
Fixes: 8a652a17e3 ("media: uvcvideo: Ensure all probed info is returned to v4l2")
Reported-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 031b9212ee ]
When DEBUG is defined this error occurs
drivers/media/platform/pxa_camera.c:1410:7: error:
‘i’ undeclared (first use in this function)
for (i = 0; i < vb->num_planes; i++)
^
The variable 'i' is missing, so declare it.
Fixes: 6f28435d1c ("[media] media: platform: pxa_camera: trivial move of functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2de3643c5 ]
This function looks like a realloc.
However, if 'risc->cpu != NULL', the memory will be freed, but never
reallocated with the bigger 'size'.
Explicitly set 'risc->cpu' to NULL, so that the reallocation is
correctly performed a few lines below.
[hverkuil: NULL != risc->cpu -> risc->cpu]
Fixes: 5ede94c705 ("[media] cx25821: remove bogus btcx_risc dependency)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a3e78f8c ]
There's a comma used instead of a semicolon that causes multiple
statements to be executed after an if instead of just the intended
single statement.
Replace the comma with a semicolon.
Fixes: 15e1ce3318 ("[media] lmedm04: Fix usb_submit_urb BOGUS urb xfer, pipe 1 != type 3 in interrupt urb")
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7f2b43eaf ]
Renaming 'struct device_private' to 'struct bcm_device_private',
because it clashes with 'struct device_private' from
'drivers/base/base.h'.
While it's not a functional problem, it's causing two distinct
type hierarchies in BTF data. It also breaks build with options:
CONFIG_DEBUG_INFO_BTF=y
CONFIG_CRYPTO_DEV_BCM_SPU=y
as reported by Qais Yousef [1].
[1] https://lore.kernel.org/lkml/20201229151352.6hzmjvu3qh6p2qgg@e107158-lin/
Fixes: 9d12ba86f8 ("crypto: brcm - Add Broadcom SPU driver")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76aaf8a967 ]
When usb_clear_halt() fails, dvb->bulk_urb->transfer_buffer
and dvb->bulk_urb should be freed just like when
usb_submit_urb() fails.
Fixes: 3169c9b26f ("V4L/DVB (12788): tm6000: Add initial DVB-T support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc1eb7c9c2 ]
The driver currently reports a single supported value for
V4L2_CID_PIXEL_RATE and initializes the control's minimum value to 0,
which is very risky, as userspace might accidentally use it as divider
when calculating the time duration of a line.
Fix this by using as minimum the only supported value when registering
the control.
Fixes: 5de35c9b8d ("media: i2c: Add Omnivision OV5670 5M sensor support")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6f2a9e17b ]
When building xway_defconfig with clang:
arch/mips/lantiq/irq.c:305:48: error: use of logical '&&' with constant
operand [-Werror,-Wconstant-logical-operand]
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
^ ~~~~~~~~~~~~~~~~~
arch/mips/lantiq/irq.c:305:48: note: use '&' for a bitwise operation
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
^~
&
arch/mips/lantiq/irq.c:305:48: note: remove constant to silence this
warning
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
~^~~~~~~~~~~~~~~~~~~~
1 error generated.
Explicitly compare the constant LTQ_EBU_PCC_ISTAT against 0 to fix the
warning. Additionally, remove the unnecessary parentheses as this is a
simple conditional statement and shorthand '== 0' to '!'.
Fixes: 3645da0276 ("OF: MIPS: lantiq: implement irq_domain support")
Link: https://github.com/ClangBuiltLinux/linux/issues/807
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c58734eee6 ]
When building with clang, the following section mismatch warning occurs:
WARNING: modpost: vmlinux.o(.text+0x24490): Section mismatch in
reference from the function r4k_cache_init() to the function
.init.text:loongson2_sc_init()
This should have been fixed with commit ad4fddef5f ("mips: fix Section
mismatch in reference") but it was missed. Remove the improper __init
annotation like that commit did.
Fixes: 078a55fc82 ("MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code")
Link: https://github.com/ClangBuiltLinux/linux/issues/787
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bc3dd24e7 ]
With the recent kmap change, some tests which were conditional on
CONFIG_DEBUG_HIGHMEM now are enabled by default.
This permit to detect a problem in sun4i-ss usage of kmap.
sun4i-ss uses two kmap via sg_miter (one for input, one for output), but
using two kmap at the same time is hard:
"the ordering has to be correct and with sg_miter that's probably hard to get
right." (quoting Tlgx)
So the easiest solution is to never have two sg_miter/kmap open at the same time.
After each use of sg_miter, I store the current index, for being able to
resume sg_miter to the right place.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ccc39b3a ]
The main problem with this error handling was that it didn't clean up if
i2c_add_numbered_adapter() failed. This code is pretty old, and doesn't
match with today's checkpatch.pl standards so I took the opportunity to
tidy it up a bit. I changed the NULL comparison, and removed the
WARNING message if kzalloc() fails and updated the label names.
Fixes: 1b082ccf59 ("gma500: Add Oaktrail support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/X8ikkAqZfnDO2lu6@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9bf87128 ]
According to Errata #23 "The per-CPU GbE interrupt is limited to Core
0", we can't use the per-cpu interrupt mechanism on the Armada 3700
familly.
This is correctly checked for RSS configuration, but the initial queue
mapping is still done by having the queues spread across all the CPUs in
the system, both in the init path and in the cpu_hotplug path.
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84fe68eb67 ]
Normally, auto negotiation and reconnect should be automatically done by
the hardware. But there seems to be an issue where auto negotiation has
to be restarted manually. This happens because of link training and so
even though still connected to the partner the link never "comes back".
This needs an auto-negotiation restart.
Also, a change in xgbe-mdio is needed to get ethtool to recognize the
link down and get the link change message. This change is only
required in a backplane connection mode.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30b7edc82e ]
Sometimes mailbox commands timeout when the RX data path becomes
unresponsive. This prevents the submission of new mailbox commands to DXIO.
This patch identifies the timeout and resets the RX data path so that the
next message can be submitted properly.
Fixes: 549b32af9f ("amd-xgbe: Simplify mailbox interface rate change code")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d3a7b9ea5 ]
Timeout reset will trigger the VIOS to unmap it automatically,
similarly as FAILVOER and MOBILITY events. If we unmap it
in the linux side, we will see errors like
"30000003: Error 4 in REQUEST_UNMAP_RSP".
So, don't call send_request_unmap for timeout reset.
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4773acf3d4 ]
The documentation for the PHY update [1] states:
Loop 4 times with index i
If PHY Revision >= 3
Copy table[i] to coef[i]
Otherwise
Set coef[i] to 0
the copy of the table to coef is currently implemented the wrong way
around, table is being updated from uninitialized values in coeff.
Fix this by swapping the assignment around.
[1] https://bcm-v4.sipsolutions.net/802.11/PHY/N/RestoreCal/
Fixes: 2f258b74d1 ("b43: N-PHY: implement restoring general configuration")
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6194f7e647 ]
The multiplication of the u32 variables tx_time and estimated_retx is
performed using a 32 bit multiplication and the result is stored in
a u64 result. This has a potential u32 overflow issue, so avoid this
by casting tx_time to a u64 to force a 64 bit multiply.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 050ac52cbe ("mac80211: code for on-demand Hybrid Wireless Mesh Protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210205175352.208841-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3daf3d391 ]
In case of a common event for rx and tx queue the event should be
regarded to be spurious if no rx and no tx requests are pending.
Unfortunately the condition for testing that is wrong causing to
decide a event being spurious if no rx OR no tx requests are
pending.
Fix that plus using local variables for rx/tx pending indicators in
order to split function calls and if condition.
Fixes: 23025393db ("xen/netback: use lateeoi irq binding")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 132e0b65dc ]
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6df8fb8330 ]
For double-checked locking in bpf_common_lru_push_free(), node->type is
read outside the critical section and then re-checked under the lock.
However, concurrent writes to node->type result in data races.
For example, the following concurrent access was observed by KCSAN:
write to 0xffff88801521bc22 of 1 bytes by task 10038 on cpu 1:
__bpf_lru_node_move_in kernel/bpf/bpf_lru_list.c:91
__local_list_flush kernel/bpf/bpf_lru_list.c:298
...
read to 0xffff88801521bc22 of 1 bytes by task 10043 on cpu 0:
bpf_common_lru_push_free kernel/bpf/bpf_lru_list.c:507
bpf_lru_push_free kernel/bpf/bpf_lru_list.c:555
...
Fix the data races where node->type is read outside the critical section
(for double-checked locking) by marking the access with READ_ONCE() as
well as ensuring the variable is only accessed once.
Fixes: 3a08c2fd76 ("bpf: LRU List")
Reported-by: syzbot+3536db46dfa58c573458@syzkaller.appspotmail.com
Reported-by: syzbot+516acdb03d3e27d91bcd@syzkaller.appspotmail.com
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210209112701.3341724-1-elver@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f9942c61f ]
Building with the clang integrated assembler produces a couple of
errors for the s3c24xx fiq support:
arch/arm/mach-s3c/irq-s3c24xx-fiq.S:52:2: error: instruction 'subne' can not set flags, but 's' suffix specified
subnes pc, lr, #4 @@ return, still have work to do
arch/arm/mach-s3c/irq-s3c24xx-fiq.S:64:1: error: invalid symbol redefinition
s3c24xx_spi_fiq_txrx:
There are apparently two problems: one with extraneous or duplicate
labels, and one with old-style opcode mnemonics. Stefan Agner has
previously fixed other problems like this, but missed this particular
file.
Fixes: bec0806cfe ("spi_s3c24xx: add FIQ pseudo-DMA support")
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210204162416.3030114-1-arnd@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9e38cabd ]
With some USB network adapters, such as DM96xx, the following message
is seen for each maximum size receive packet.
dwc2 ff540000.usb: dwc2_update_urb_state(): trimming xfer length
This happens because the packet size requested by the driver is 1522
bytes, wMaxPacketSize is 64, the dwc2 driver configures the chip to
receive 24*64 = 1536 bytes, and the chip does indeed send more than
1522 bytes of data. Since the event does not indicate an error condition,
the message is just noise. Demote it to debug level.
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f74b68c61c ]
In some situations, the following error messages are reported.
dwc2 ff540000.usb: dwc2_hc_chhltd_intr_dma: Channel 1 - ChHltd set, but reason is unknown
dwc2 ff540000.usb: hcint 0x00000002, intsts 0x04000021
This is sometimes followed by:
dwc2 ff540000.usb: dwc2_update_urb_state_abn(): trimming xfer length
and then:
WARNING: CPU: 0 PID: 0 at kernel/v4.19/drivers/usb/dwc2/hcd.c:2913
dwc2_assign_and_init_hc+0x98c/0x990
The warning suggests that an odd buffer address is to be used for DMA.
After an error is observed, the receive buffer may be full
(urb->actual_length >= urb->length). However, the urb is still left in
the queue unless three errors were observed in a row. When it is queued
again, the dwc2 hcd code translates this into a 1-block transfer.
If urb->actual_length (ie the total expected receive length) is not
DMA-aligned, the buffer pointer programmed into the chip will be
unaligned. This results in the observed warning.
To solve the problem, abort input transactions after an error with
unknown cause if the entire packet was already received. This may be
a bit drastic, but we don't really know why the transfer was aborted
even though the entire packet was received. Aborting the transfer in
this situation is less risky than accepting a potentially corrupted
packet.
With this patch in place, the 'ChHltd set' and 'trimming xfer length'
messages are still observed, but there are no more transfer attempts
with odd buffer addresses.
Fixes: 151d0cbdbe ("usb: dwc2: make the scheduler handle excessive NAKs better")
Cc: Boris ARZUR <boris@konbu.org>
Cc: Douglas Anderson <dianders@chromium.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-3-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415fa1c730 ]
The DWC2 documentation states that transfers with zero data length should
set the number of packets to 1 and the transfer length to 0. This is not
currently the case for inbound transfers: the transfer length is set to
the maximum packet length. This can have adverse effects if the chip
actually does transfer data as it is programmed to do. Follow chip
documentation and keep the transfer length set to 0 in that situation.
Fixes: 56f5b1cff2 ("staging: Core files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-2-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f416879a ]
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb88 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a758c861 ]
Jump to the label done to decrement the reference count of HCI device
hdev on path that the Inquiry procedure is interrupted.
Fixes: 3e13fa1e1f ("Bluetooth: Fix hci_inquiry ioctl usage")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de8681be2 ]
As per the kernel doc for usb_ep_dequeue(), it states that "this
routine is asynchronous, that is, it may return before the completion
routine runs". And indeed since v5.0 the dwc3 gadget driver updated
its behavior to place dequeued requests on to a cancelled list to be
given back later after the endpoint is stopped.
The free_ep() was incorrectly assuming that a request was ready to
be freed after calling dequeue which results in a use-after-free
in dwc3 when it traverses its cancelled list. Fix this by moving
the usb_ep_free_request() call to the callback itself in case the
ep is disabled.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Reported-and-tested-by: Ferry Toth <fntoth@gmail.com>
Reviewed-and-tested-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fea2eb2f5 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 9589f7721e ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98e2367df ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e6a5467c ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437ae60947 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: faaf348ef4 ("ARM: dts: Add board dts file for exynos3250-rinato")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8528cda2b7 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: e0cefb3f79 ("ARM: dts: add board dts file for Exynos3250-based Monk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-2-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5687c6440 ]
Looks like this was missed when patching the source to clear the structures
throughout, causing this one instance to clear the struct after the response
id is assigned.
Fixes: eddb773211 ("Bluetooth: A2MP: Fix not initializing all members")
Signed-off-by: Christopher William Snowhill <chris@kode54.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a39a927be ]
Some resource should be released in the error handling path of the probe
function, as already done in the remove function.
The remove function was fixed in commit 5052de8def ("soc: qcom: smd:
Transition client drivers from smd to rpmsg")
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8ac7c87acd upstream.
MIPS uses its own declaration of rwdata, and thus it should be kept
in sync with the asm-generic one. Currently PAGE_ALIGNED_DATA() is
missing from the linker script, which emits the following ld
warnings:
mips-alpine-linux-musl-ld: warning: orphan section
`.data..page_aligned' from `arch/mips/kernel/vdso.o' being placed
in section `.data..page_aligned'
mips-alpine-linux-musl-ld: warning: orphan section
`.data..page_aligned' from `arch/mips/vdso/vdso-image.o' being placed
in section `.data..page_aligned'
Add the necessary declaration, so the mentioned structures will be
placed in vmlinux as intended:
ffffffff80630580 D __end_once
ffffffff80630580 D __start___dyndbg
ffffffff80630580 D __start_once
ffffffff80630580 D __stop___dyndbg
ffffffff80634000 d mips_vdso_data
ffffffff80638000 d vdso_data
ffffffff80638580 D _gp
ffffffff8063c000 T __init_begin
ffffffff8063c000 D _edata
ffffffff8063c000 T _sinittext
->
ffffffff805a4000 D __end_init_task
ffffffff805a4000 D __nosave_begin
ffffffff805a4000 D __nosave_end
ffffffff805a4000 d mips_vdso_data
ffffffff805a8000 d vdso_data
ffffffff805ac000 D mmlist_lock
ffffffff805ac080 D tasklist_lock
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93f7a6d818 upstream.
Currently kdb uses in_interrupt() to determine whether its library
code has been called from the kgdb trap handler or from a saner calling
context such as driver init. This approach is broken because
in_interrupt() alone isn't able to determine kgdb trap handler entry from
normal task context. This can happen during normal use of basic features
such as breakpoints and can also be trivially reproduced using:
echo g > /proc/sysrq-trigger
We can improve this by adding check for in_dbg_master() instead which
explicitly determines if we are running in debugger context.
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1611313556-4004-1-git-send-email-sumit.garg@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4fa46b30 upstream.
We expect toolchains to produce these new debug info sections as part of
DWARF v5. Add explicit placements to prevent the linker warnings from
--orphan-section=warn.
Compilers may produce such sections with explicit -gdwarf-5, or based on
the implicit default version of DWARF when -g is used via DEBUG_INFO.
This implicit default changes over time, and has changed to DWARF v5
with GCC 11.
.debug_sup was mentioned in review, but without compilers producing it
today, let's wait to add it until it becomes necessary.
Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1922707
Reported-by: Chris Murphy <lists@colorremedies.com>
Suggested-by: Fangrui Song <maskray@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Mark Wielaard <mark@klomp.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a738c93fb1 ]
While debugging another issue today, Steve and I noticed that if a
subdir for a file share is already mounted on the client, any new
mount of any other subdir (or the file share root) of the same share
results in sharing the cifs superblock, which e.g. can result in
incorrect device name.
While setting prefix path for the root of a cifs_sb,
CIFS_MOUNT_USE_PREFIX_PATH flag should also be set.
Without it, prepath is not even considered in some places,
and output of "mount" and various /proc/<>/*mount* related
options can be missing part of the device name.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e0ca54674 upstream.
HDA initialization is failing occasionally on Tegra210 and following
print is observed in the boot log. Because of this probe() fails and
no sound card is registered.
[16.800802] tegra-hda 70030000.hda: no codecs found!
Codecs request a state change and enumeration by the controller. In
failure cases this does not seem to happen as STATETS register reads 0.
The problem seems to be related to the HDA codec dependency on SOR
power domain. If it is gated during HDA probe then the failure is
observed. Building Tegra HDA driver into kernel image avoids this
failure but does not completely address the dependency part. Fix this
problem by adding 'power-domains' DT property for Tegra210 HDA. Note
that Tegra186 and Tegra194 HDA do this already.
Fixes: 742af7e7a0 ("arm64: tegra: Add Tegra210 support")
Depends-on: 96d1f078ff ("arm64: tegra: Add SOR power-domain for Tegra210")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9be64eef upstream.
The HID subsystem allows an "HID report field" to have a different
number of "values" and "usages" when it is allocated. When a field
struct is created, the size of the usage array is guaranteed to be at
least as large as the values array, but it may be larger. This leads to
a potential out-of-bounds write in
__hidinput_change_resolution_multipliers() and an out-of-bounds read in
hidinput_count_leds().
To fix this, let's make sure that both the usage and value arrays are
the same size.
Cc: stable@vger.kernel.org
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88bf56d04b upstream
In kvm_mmu_notifier_invalidate_range_start(), tlbs_dirty is used as:
need_tlb_flush |= kvm->tlbs_dirty;
with need_tlb_flush's type being int and tlbs_dirty's type being long.
It means that tlbs_dirty is always used as int and the higher 32 bits
is useless. We need to check tlbs_dirty in a correct way and this
change checks it directly without propagating it to need_tlb_flush.
Note: it's _extremely_ unlikely this neglecting of higher 32 bits can
cause problems in practice. It would require encountering tlbs_dirty
on a 4 billion count boundary, and KVM would need to be using shadow
paging or be running a nested guest.
Cc: stable@vger.kernel.org
Fixes: a4ee1ca4a3 ("KVM: MMU: delay flush all tlbs on sync_page path")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20201217154118.16497-1-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eea52743eb upstream
Fixes: <b3e3893e1253> ("net: use core MTU range checking")
which patched only one of two functions used to setup the
USB Gadget Ethernet driver, causing a serious performance
regression in the ability to increase mtu size above 1500.
Signed-off-by: John Greb <h3x4m3r0n@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 871997bc9e upstream.
The function uses a goto-based loop, which may lead to an earlier error
getting discarded by a later iteration. Exit this ad-hoc loop when an
error was encountered.
The out-of-memory error path additionally fails to fill a structure
field looked at by xen_blkbk_unmap_prepare() before inspecting the
handle which does get properly set (to BLKBACK_INVALID_HANDLE).
Since the earlier exiting from the ad-hoc loop requires the same field
filling (invalidation) as that on the out-of-memory path, fold both
paths. While doing so, drop the pr_alert(), as extra log messages aren't
going to help the situation (the kernel will log oom conditions already
anyway).
This is XSA-365.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c77474b2d upstream.
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3194a1746e upstream.
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a264285ed upstream.
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36bf1dfb8b upstream.
set_phys_to_machine can fail due to lack of memory, see the kzalloc call
in arch/arm/xen/p2m.c:__set_phys_to_machine_multi.
Don't ignore the potential return error in set_foreign_p2m_mapping,
returning it to the caller instead.
This is part of XSA-361.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Cc: stable@vger.kernel.org
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebee0eab08 upstream.
Failure of the kernel part of the mapping operation should also be
indicated as an error to the caller, or else it may assume the
respective kernel VA is okay to access.
Furthermore gnttab_map_refs() failing still requires recording
successfully mapped handles, so they can be unmapped subsequently. This
in turn requires there to be a way to tell full hypercall failure from
partial success - preset map_op status fields such that they won't
"happen" to look as if the operation succeeded.
Also again use GNTST_okay instead of implying its value (zero).
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbe5283605 upstream.
We may not skip setting the field in the unmap structure when
GNTMAP_device_map is in use - such an unmap would fail to release the
respective resources (a page ref in the hypervisor). Otoh the field
doesn't need setting at all when GNTMAP_device_map is not in use.
To record the value for unmapping, we also better don't use our local
p2m: In particular after a subsequent change it may not have got updated
for all the batch elements. Instead it can simply be taken from the
respective map's results.
We can additionally avoid playing this game altogether for the kernel
part of the mappings in (x86) PV mode.
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b512e1b077 upstream.
We should not set up further state if either mapping failed; paying
attention to just the user mapping's status isn't enough.
Also use GNTST_okay instead of implying its value (zero).
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a35f2ef3b7 upstream.
Its sibling (set_foreign_p2m_mapping()) as well as the sibling of its
only caller (gnttab_map_refs()) don't clean up after themselves in case
of error. Higher level callers are expected to do so. However, in order
for that to really clean up any partially set up state, the operation
should not terminate upon encountering an entry in unexpected state. It
is particularly relevant to notice here that set_foreign_p2m_mapping()
would skip setting up a p2m entry if its grant mapping failed, but it
would continue to set up further p2m entries as long as their mappings
succeeded.
Arguably down the road set_foreign_p2m_mapping() may want its page state
related WARN_ON() also converted to an error return.
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07d0408120 upstream.
Currently if CONFIG_FTRACE_MCOUNT_RECORD is enabled -mrecord-mcount
compiler flag support is tested for every Makefile.
Top 4 cc-option usages:
511 -mrecord-mcount
11 -fno-stack-protector
9 -Wno-override-init
2 -fsched-pressure
To address that move cc-option from scripts/Makefile.build to top Makefile
and export CC_USING_RECORD_MCOUNT to be used in original place.
While doing that also add -mrecord-mcount to CC_FLAGS_FTRACE (if gcc
actually supports it).
Link: http://lkml.kernel.org/r/patch-2.thread-aa7b8d.git-de935bace15a.your-ad-here.call-01533557518-ext-9465@work.hours
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96f60dfa58 upstream.
gcc 5 supports a new -mcount-record option to generate ftrace
tables directly. This avoids the need to run record_mcount
manually.
Use this option when available.
So far doesn't use -mcount-nop, which also exists now.
This is needed to make ftrace work with LTO because the
normal record-mcount script doesn't run over the link
time output.
It should also improve build times slightly in the general
case.
Link: http://lkml.kernel.org/r/20171127213423.27218-12-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d6a3d3a2a ]
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1c5fae9c9a upstream.
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7536bc73 upstream.
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aa6bce9af upstream.
Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:
netif_carrier_off(dev);
netif_tx_disable(dev);
driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.
Fixes: c3f26a269c ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fca3f13810 upstream
Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.
Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.
[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
October 20, 2004, pp. 30 - 36.
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07998281c2 ]
The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.
This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.
This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.
Fixes: 4e35c1cb94 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dcb396454 ]
With kaslr the kernel image is placed at a random place, so starting the
bottom-up allocation with the kernel_end can result in an allocation
failure and a warning like this one:
hugetlb_cma: reserve 2048 MiB, up to 2048 MiB per node
------------[ cut here ]------------
memblock: bottom-up allocation failed, memory hotremove may be affected
WARNING: CPU: 0 PID: 0 at mm/memblock.c:332 memblock_find_in_range_node+0x178/0x25a
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.10.0+ #1169
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
RIP: 0010:memblock_find_in_range_node+0x178/0x25a
Code: e9 6d ff ff ff 48 85 c0 0f 85 da 00 00 00 80 3d 9b 35 df 00 00 75 15 48 c7 c7 c0 75 59 88 c6 05 8b 35 df 00 01 e8 25 8a fa ff <0f> 0b 48 c7 44 24 20 ff ff ff ff 44 89 e6 44 89 ea 48 c7 c1 70 5c
RSP: 0000:ffffffff88803d18 EFLAGS: 00010086 ORIG_RAX: 0000000000000000
RAX: 0000000000000000 RBX: 0000000240000000 RCX: 00000000ffffdfff
RDX: 00000000ffffdfff RSI: 00000000ffffffea RDI: 0000000000000046
RBP: 0000000100000000 R08: ffffffff88922788 R09: 0000000000009ffb
R10: 00000000ffffe000 R11: 3fffffffffffffff R12: 0000000000000000
R13: 0000000000000000 R14: 0000000080000000 R15: 00000001fb42c000
FS: 0000000000000000(0000) GS:ffffffff88f71000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffa080fb401000 CR3: 00000001fa80a000 CR4: 00000000000406b0
Call Trace:
memblock_alloc_range_nid+0x8d/0x11e
cma_declare_contiguous_nid+0x2c4/0x38c
hugetlb_cma_reserve+0xdc/0x128
flush_tlb_one_kernel+0xc/0x20
native_set_fixmap+0x82/0xd0
flat_get_apic_id+0x5/0x10
register_lapic_address+0x8e/0x97
setup_arch+0x8a5/0xc3f
start_kernel+0x66/0x547
load_ucode_bsp+0x4c/0xcd
secondary_startup_64_no_verify+0xb0/0xbb
random: get_random_bytes called from __warn+0xab/0x110 with crng_init=0
---[ end trace f151227d0b39be70 ]---
At the same time, the kernel image is protected with memblock_reserve(),
so we can just start searching at PAGE_SIZE. In this case the bottom-up
allocation has the same chances to success as a top-down allocation, so
there is no reason to fallback in the case of a failure. All together it
simplifies the logic.
Link: https://lkml.kernel.org/r/20201217201214.3414100-2-guro@fb.com
Fixes: 8fabc62323 ("powerpc: Ensure that swiotlb buffer is allocated from low memory")
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Wonhyuk Yang <vvghjk1234@gmail.com>
Cc: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c698bff66 ]
Ensure that the signal page contains our poison instruction to increase
the protection against ROP attacks and also contains well defined
contents.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5638159f6d ]
This reverts commit c17e9377aa.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fedf9359 ]
When inode has no listxattr op of its own (e.g. squashfs) vfs_listxattr
calls the LSM inode_listsecurity hooks to list the xattrs that LSMs will
intercept in inode_getxattr hooks.
When selinux LSM is installed but not initialized, it will list the
security.selinux xattr in inode_listsecurity, but will not intercept it
in inode_getxattr. This results in -ENODATA for a getxattr call for an
xattr returned by listxattr.
This situation was manifested as overlayfs failure to copy up lower
files from squashfs when selinux is built-in but not initialized,
because ovl_copy_xattr() iterates the lower inode xattrs by
vfs_listxattr() and vfs_getxattr().
ovl_copy_xattr() skips copy up of security labels that are indentified by
inode_copy_up_xattr LSM hooks, but it does that after vfs_getxattr().
Since we are not going to copy them, skip vfs_getxattr() of the security
labels.
Reported-by: Michael Labriola <michael.d.labriola@gmail.com>
Tested-by: Michael Labriola <michael.d.labriola@gmail.com>
Link: https://lore.kernel.org/linux-unionfs/2nv9d47zt7.fsf@aldarion.sourceruckus.org/
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2b00be488 ]
If a capability is stored on disk in v2 format cap_inode_getsecurity() will
currently return in v2 format unconditionally.
This is wrong: v2 cap should be equivalent to a v3 cap with zero rootid,
and so the same conversions performed on it.
If the rootid cannot be mapped, v3 is returned unconverted. Fix this so
that both v2 and v3 return -EOVERFLOW if the rootid (or the owner of the fs
user namespace in case of v2) cannot be mapped into the current user
namespace.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554677b972 ]
The vfs_getxattr() in ovl_xattr_set() is used to check whether an xattr
exist on a lower layer file that is to be removed. If the xattr does not
exist, then no need to copy up the file.
This call of vfs_getxattr() wasn't wrapped in credential override, and this
is probably okay. But for consitency wrap this instance as well.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67fbe02a5c ]
Recently userspace has started making more use of SW_TABLET_MODE
(when an input-dev reports this).
Specifically recent GNOME3 versions will:
1. When SW_TABLET_MODE is reported and is reporting 0:
1.1 Disable accelerometer-based screen auto-rotation
1.2 Disable automatically showing the on-screen keyboard when a
text-input field is focussed
2. When SW_TABLET_MODE is reported and is reporting 1:
2.1 Ignore input-events from the builtin keyboard and touchpad
(this is for 360° hinges style 2-in-1s where the keyboard and
touchpads are accessible on the back of the tablet when folded
into tablet-mode)
This means that claiming to support SW_TABLET_MODE when it does not
actually work / reports correct values has bad side-effects.
The check in the hp-wmi code which is used to decide if the input-dev
should claim SW_TABLET_MODE support, only checks if the
HPWMI_HARDWARE_QUERY is supported. It does *not* check if the hardware
actually is capable of reporting SW_TABLET_MODE.
This leads to the hp-wmi input-dev claiming SW_TABLET_MODE support,
while in reality it will always report 0 as SW_TABLET_MODE value.
This has been seen on a "HP ENVY x360 Convertible 15-cp0xxx" and
this likely is the case on a whole lot of other HP models.
This problem causes both auto-rotation and on-screen keyboard
support to not work on affected x360 models.
There is no easy fix for this, but since userspace expects
SW_TABLET_MODE reporting to be reliable when advertised it is
better to not claim/report SW_TABLET_MODE support at all, then
to claim to support it while it does not work.
To avoid the mentioned problems, add a new enable_tablet_mode_sw
module-parameter which defaults to false.
Note I've made this an int using the standard -1=auto, 0=off, 1=on
triplett, with the hope that in the future we can come up with a
better way to detect SW_TABLET_MODE support. ATM the default
auto option just does the same as off.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1918255
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210120124941.73409-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43f20b1c61 ]
It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.
Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200815125112.462652-3-maz@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4295ab0b4 upstream.
After Commit 3499ba8198 ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.
If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).
We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.
After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.
Cc: stable@vger.kernel.org
Fixes: 3499ba8198 ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b220c049d5 upstream.
When filters are used by trace events, a page is allocated on each CPU and
used to copy the trace event fields to this page before writing to the ring
buffer. The reason to use the filter and not write directly into the ring
buffer is because a filter may discard the event and there's more overhead
on discarding from the ring buffer than the extra copy.
The problem here is that there is no check against the size being allocated
when using this page. If an event asks for more than a page size while being
filtered, it will get only a page, leading to the caller writing more that
what was allocated.
Check the length of the request, and if it is more than PAGE_SIZE minus the
header default back to allocating from the ring buffer directly. The ring
buffer may reject the event if its too big anyway, but it wont overflow.
Link: https://lore.kernel.org/ath10k/1612839593-2308-1-git-send-email-wgong@codeaurora.org/
Cc: stable@vger.kernel.org
Fixes: 0fc1b09ff1 ("tracing: Use temp buffer when filtering events")
Reported-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 256cfdd6fd upstream.
The file /sys/kernel/tracing/events/enable is used to enable all events by
echoing in "1", or disabling all events when echoing in "0". To know if all
events are enabled, disabled, or some are enabled but not all of them,
cating the file should show either "1" (all enabled), "0" (all disabled), or
"X" (some enabled but not all of them). This works the same as the "enable"
files in the individule system directories (like tracing/events/sched/enable).
But when all events are enabled, the top level "enable" file shows "X". The
reason is that its checking the "ftrace" events, which are special events
that only exist for their format files. These include the format for the
function tracer events, that are enabled when the function tracer is
enabled, but not by the "enable" file. The check includes these events,
which will always be disabled, and even though all true events are enabled,
the top level "enable" file will show "X" instead of "1".
To fix this, have the check test the event's flags to see if it has the
"IGNORE_ENABLE" flag set, and if so, not test it.
Cc: stable@vger.kernel.org
Fixes: 553552ce17 ("tracing: Combine event filter_active and enable into single flags field")
Reported-by: "Yordan Karadzhov (VMware)" <y.karadz@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eabac19e40 upstream.
Sysbot has reported an "slab-out-of-bounds read" error which has been
identified as being caused by a corrupted "ino_num" value read from the
inode. This could be because the metadata block is uncompressed, or
because the "compression" bit has been corrupted (turning a compressed
block into an uncompressed block).
This patch adds additional sanity checks to detect this, and the
following corruption.
1. It checks against corruption of the inodes count. This can either
lead to a larger table to be read, or a smaller than expected
table to be read.
In the case of a too large inodes count, this would often have been
trapped by the existing sanity checks, but this patch introduces
a more exact check, which can identify too small values.
2. It checks the contents of the index table for corruption.
[phillip@squashfs.org.uk: fix checkpatch issue]
Link: https://lkml.kernel.org/r/527909353.754618.1612769948607@webmail.123-reg.co.uk
Link: https://lkml.kernel.org/r/20210204130249.4495-4-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: syzbot+04419e3ff19d2970ea28@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68f23b8906 ]
Without memcg, there is a one-to-one mapping between the bdi and
bdi_writeback structures. In this world, things are fairly
straightforward; the first thing bdi_unregister() does is to shutdown
the bdi_writeback structure (or wb), and part of that writeback ensures
that no other work queued against the wb, and that the wb is fully
drained.
With memcg, however, there is a one-to-many relationship between the bdi
and bdi_writeback structures; that is, there are multiple wb objects
which can all point to a single bdi. There is a refcount which prevents
the bdi object from being released (and hence, unregistered). So in
theory, the bdi_unregister() *should* only get called once its refcount
goes to zero (bdi_put will drop the refcount, and when it is zero,
release_bdi gets called, which calls bdi_unregister).
Unfortunately, del_gendisk() in block/gen_hd.c never got the memo about
the Brave New memcg World, and calls bdi_unregister directly. It does
this without informing the file system, or the memcg code, or anything
else. This causes the root wb associated with the bdi to be
unregistered, but none of the memcg-specific wb's are shutdown. So when
one of these wb's are woken up to do delayed work, they try to
dereference their wb->bdi->dev to fetch the device name, but
unfortunately bdi->dev is now NULL, thanks to the bdi_unregister()
called by del_gendisk(). As a result, *boom*.
Fortunately, it looks like the rest of the writeback path is perfectly
happy with bdi->dev and bdi->owner being NULL, so the simplest fix is to
create a bdi_dev_name() function which can handle bdi->dev being NULL.
This also allows us to bulletproof the writeback tracepoints to prevent
them from dereferencing a NULL pointer and crashing the kernel if one is
tracing with memcg's enabled, and an iSCSI device dies or a USB storage
stick is pulled.
The most common way of triggering this will be hotremoval of a device
while writeback with memcg enabled is going on. It was triggering
several times a day in a heavily loaded production environment.
Google Bug Id: 145475544
Link: https://lore.kernel.org/r/20191227194829.150110-1-tytso@mit.edu
Link: http://lkml.kernel.org/r/20191228005211.163952-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Chris Mason <clm@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1a445d3b8 ]
There are many of those warnings.
In file included from ./arch/powerpc/include/asm/paca.h:15,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./include/asm-generic/preempt.h:5,
from ./arch/powerpc/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:51,
from fs/fs-writeback.c:19:
In function 'strncpy',
inlined from 'perf_trace_writeback_page_template' at
./include/trace/events/writeback.h:56:1:
./include/linux/string.h:260:9: warning: '__builtin_strncpy' specified
bound 32 equals destination size [-Wstringop-truncation]
return __builtin_strncpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by using the new strscpy_pad() which was introduced in "lib/string:
Add strscpy_pad() function" and will always be NUL-terminated instead of
strncpy(). Also, change strlcpy() to use strscpy_pad() in this file for
consistency.
Link: http://lkml.kernel.org/r/1564075099-27750-1-git-send-email-cai@lca.pw
Fixes: 455b286468 ("writeback: Initial tracing support")
Fixes: 028c2dd184 ("writeback: Add tracing to balance_dirty_pages")
Fixes: e84d0a4f8e ("writeback: trace event writeback_queue_io")
Fixes: b48c104d22 ("writeback: trace event bdi_dirty_ratelimit")
Fixes: cc1676d917 ("writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()")
Fixes: 9fb0a7da0c ("writeback: add more tracepoints")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Tobin C. Harding <tobin@kernel.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Joe Perches <joe@perches.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Jann Horn <jannh@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Nitin Gote <nitin.r.gote@intel.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Stephen Kitt <steve@sk2.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 458a3bf82d ]
We have a function to copy strings safely and we have a function to copy
strings and zero the tail of the destination (if source string is
shorter than destination buffer) but we do not have a function to do
both at once. This means developers must write this themselves if they
desire this functionality. This is a chore, and also leaves us open to
off by one errors unnecessarily.
Add a function that calls strscpy() then memset()s the tail to zero if
the source string is shorter than the destination buffer.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba6dfce47c ]
Remove duplicated helper functions to parse opaque XDR objects
and place inside new file net/sunrpc/auth_gss/auth_gss_internal.h.
In the new file carry the license and copyright from the source file
net/sunrpc/auth_gss/auth_gss.c. Finally, update the comment inside
include/linux/sunrpc/xdr.h since lockd is not the only user of
struct xdr_netobj.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08bd8dbe88 ]
If the server returns a new stateid that does not match the one in our
cache, then try to return the one we hold instead of just invalidating
it on the client side. This ensures that both client and server will
agree that the stateid is invalid.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afbc293add ]
xfrm_probe_algs() probes kernel crypto modules and changes the
availability of struct xfrm_algo_desc. But there is a small window
where ealg->available and aalg->available get changed between
count_ah_combs()/count_esp_combs() and dump_ah_combs()/dump_esp_combs(),
in this case we may allocate a smaller skb but later put a larger
amount of data and trigger the panic in skb_put().
Fix this by relaxing the checks when counting the size, that is,
skipping the test of ->available. We may waste some memory for a few
of sizeof(struct sadb_comb), but it is still much better than a panic.
Reported-by: syzbot+b2bf2652983d23734c5c@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e013f455d9 upstream
The following mem abort is observed when the mba firmware size exceeds
the allocated mba region. MBA firmware size is restricted to a maximum
size of 1M and remaining memory region is used by modem debug policy
firmware when available. Hence verify whether the MBA firmware size lies
within the allocated memory region and is not greater than 1M before
loading.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0x40/0x218
rproc_boot+0x5b4/0x608
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
__arm64_sys_write+0x24/0x30
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sudip: manual backport to old file path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 135b9e8d1c upstream
The following mem abort is observed when one of the modem blob firmware
size exceeds the allocated mpss region. Fix this by restricting the copy
size to segment size using request_firmware_into_buf before load.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0xd0/0x190
rproc_boot+0x404/0x550
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sudip: manual backport to old file path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0a922046 upstream.
On some archs, the idle task can call into cpu_suspend(). The cpu_suspend()
will disable or pause function graph tracing, as there's some paths in
bringing down the CPU that can have issues with its return address being
modified. The task_struct structure has a "tracing_graph_pause" atomic
counter, that when set to something other than zero, the function graph
tracer will not modify the return address.
The problem is that the tracing_graph_pause counter is initialized when the
function graph tracer is enabled. This can corrupt the counter for the idle
task if it is suspended in these architectures.
CPU 1 CPU 2
----- -----
do_idle()
cpu_suspend()
pause_graph_tracing()
task_struct->tracing_graph_pause++ (0 -> 1)
start_graph_tracing()
for_each_online_cpu(cpu) {
ftrace_graph_init_idle_task(cpu)
task-struct->tracing_graph_pause = 0 (1 -> 0)
unpause_graph_tracing()
task_struct->tracing_graph_pause-- (0 -> -1)
The above should have gone from 1 to zero, and enabled function graph
tracing again. But instead, it is set to -1, which keeps it disabled.
There's no reason that the field tracing_graph_pause on the task_struct can
not be initialized at boot up.
Cc: stable@vger.kernel.org
Fixes: 380c4b1411 ("tracing/function-graph-tracer: append the tracing_graph_flag")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=211339
Reported-by: pierre.gondois@arm.com
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29b3283972 upstream.
When an Intel IOMMU is virtualized, and a physical device is
passed-through to the VM, changes of the virtual IOMMU need to be
propagated to the physical IOMMU. The hypervisor therefore needs to
monitor PTE mappings in the IOMMU page-tables. Intel specifications
provide "caching-mode" capability that a virtual IOMMU uses to report
that the IOMMU is virtualized and a TLB flush is needed after mapping to
allow the hypervisor to propagate virtual IOMMU mappings to the physical
IOMMU. To the best of my knowledge no real physical IOMMU reports
"caching-mode" as turned on.
Synchronizing the virtual and the physical IOMMU tables is expensive if
the hypervisor is unaware which PTEs have changed, as the hypervisor is
required to walk all the virtualized tables and look for changes.
Consequently, domain flushes are much more expensive than page-specific
flushes on virtualized IOMMUs with passthrough devices. The kernel
therefore exploited the "caching-mode" indication to avoid domain
flushing and use page-specific flushing in virtualized environments. See
commit 78d5f0f500 ("intel-iommu: Avoid global flushes with caching
mode.")
This behavior changed after commit 13cf017446 ("iommu/vt-d: Make use
of iova deferred flushing"). Now, when batched TLB flushing is used (the
default), full TLB domain flushes are performed frequently, requiring
the hypervisor to perform expensive synchronization between the virtual
TLB and the physical one.
Getting batched TLB flushes to use page-specific invalidations again in
such circumstances is not easy, since the TLB invalidation scheme
assumes that "full" domain TLB flushes are performed for scalability.
Disable batched TLB flushes when caching-mode is on, as the performance
benefit from using batched TLB invalidations is likely to be much
smaller than the overhead of the virtual-to-physical IOMMU page-tables
synchronization.
Fixes: 13cf017446 ("iommu/vt-d: Make use of iova deferred flushing")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210127175317.1600473-1-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25a068b8e9 upstream.
Jan Kiszka reported that the x2apic_wrmsr_fence() function uses a plain
MFENCE while the Intel SDM (10.12.3 MSR Access in x2APIC Mode) calls for
MFENCE; LFENCE.
Short summary: we have special MSRs that have weaker ordering than all
the rest. Add fencing consistent with current SDM recommendations.
This is not known to cause any issues in practice, only in theory.
Longer story below:
The reason the kernel uses a different semantic is that the SDM changed
(roughly in late 2017). The SDM changed because folks at Intel were
auditing all of the recommended fences in the SDM and realized that the
x2apic fences were insufficient.
Why was the pain MFENCE judged insufficient?
WRMSR itself is normally a serializing instruction. No fences are needed
because the instruction itself serializes everything.
But, there are explicit exceptions for this serializing behavior written
into the WRMSR instruction documentation for two classes of MSRs:
IA32_TSC_DEADLINE and the X2APIC MSRs.
Back to x2apic: WRMSR is *not* serializing in this specific case.
But why is MFENCE insufficient? MFENCE makes writes visible, but
only affects load/store instructions. WRMSR is unfortunately not a
load/store instruction and is unaffected by MFENCE. This means that a
non-serializing WRMSR could be reordered by the CPU to execute before
the writes made visible by the MFENCE have even occurred in the first
place.
This means that an x2apic IPI could theoretically be triggered before
there is any (visible) data to process.
Does this affect anything in practice? I honestly don't know. It seems
quite possible that by the time an interrupt gets to consume the (not
yet) MFENCE'd data, it has become visible, mostly by accident.
To be safe, add the SDM-recommended fences for all x2apic WRMSRs.
This also leaves open the question of the _other_ weakly-ordered WRMSR:
MSR_IA32_TSC_DEADLINE. While it has the same ordering architecture as
the x2APIC MSRs, it seems substantially less likely to be a problem in
practice. While writes to the in-memory Local Vector Table (LVT) might
theoretically be reordered with respect to a weakly-ordered WRMSR like
TSC_DEADLINE, the SDM has this to say:
In x2APIC mode, the WRMSR instruction is used to write to the LVT
entry. The processor ensures the ordering of this write and any
subsequent WRMSR to the deadline; no fencing is required.
But, that might still leave xAPIC exposed. The safest thing to do for
now is to add the extra, recommended LFENCE.
[ bp: Massage commit message, fix typos, drop accidentally added
newline to tools/arch/x86/include/asm/barrier.h. ]
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200305174708.F77040DD@viggo.jf.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20bf2b3787 upstream.
With retpolines disabled, some configurations of GCC, and specifically
the GCC versions 9 and 10 in Ubuntu will add Intel CET instrumentation
to the kernel by default. That breaks certain tracing scenarios by
adding a superfluous ENDBR64 instruction before the fentry call, for
functions which can be called indirectly.
CET instrumentation isn't currently necessary in the kernel, as CET is
only supported in user space. Disable it unconditionally and move it
into the x86's Makefile as CET/CFI... enablement should be a per-arch
decision anyway.
[ bp: Massage and extend commit message. ]
Fixes: 29be86d7f9 ("kbuild: add -fcf-protection=none when using retpoline flags")
Reported-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Tested-by: Nikolay Borisov <nborisov@suse.com>
Cc: <stable@vger.kernel.org>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lkml.kernel.org/r/20210128215219.6kct3h2eiustncws@treble
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2f67308a upstream.
Sergey reported deadlock between kswapd correctly doing its usual
lock_page(page) followed by down_read(page->mapping->i_mmap_rwsem), and
madvise(MADV_REMOVE) on an madvise(MADV_HUGEPAGE) area doing
down_write(page->mapping->i_mmap_rwsem) followed by lock_page(page).
This happened when shmem_fallocate(punch hole)'s unmap_mapping_range()
reaches zap_pmd_range()'s call to __split_huge_pmd(). The same deadlock
could occur when partially truncating a mapped huge tmpfs file, or using
fallocate(FALLOC_FL_PUNCH_HOLE) on it.
__split_huge_pmd()'s page lock was added in 5.8, to make sure that any
concurrent use of reuse_swap_page() (holding page lock) could not catch
the anon THP's mapcounts and swapcounts while they were being split.
Fortunately, reuse_swap_page() is never applied to a shmem or file THP
(not even by khugepaged, which checks PageSwapCache before calling), and
anonymous THPs are never created in shmem or file areas: so that
__split_huge_pmd()'s page lock can only be necessary for anonymous THPs,
on which there is no risk of deadlock with i_mmap_rwsem.
Link: https://lkml.kernel.org/r/alpine.LSU.2.11.2101161409470.2022@eggly.anvils
Fixes: c444eb564f ("mm: thp: make the THP mapcount atomic against __split_huge_pmd_locked()")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eb2df2b56 upstream.
There is a race between isolate_huge_page() and __free_huge_page().
CPU0: CPU1:
if (PageHuge(page))
put_page(page)
__free_huge_page(page)
spin_lock(&hugetlb_lock)
update_and_free_page(page)
set_compound_page_dtor(page,
NULL_COMPOUND_DTOR)
spin_unlock(&hugetlb_lock)
isolate_huge_page(page)
// trigger BUG_ON
VM_BUG_ON_PAGE(!PageHead(page), page)
spin_lock(&hugetlb_lock)
page_huge_active(page)
// trigger BUG_ON
VM_BUG_ON_PAGE(!PageHuge(page), page)
spin_unlock(&hugetlb_lock)
When we isolate a HugeTLB page on CPU0. Meanwhile, we free it to the
buddy allocator on CPU1. Then, we can trigger a BUG_ON on CPU0, because
it is already freed to the buddy allocator.
Link: https://lkml.kernel.org/r/20210115124942.46403-5-songmuchun@bytedance.com
Fixes: c8721bbbdd ("mm: memory-hotplug: enable memory hotplug to handle hugepage")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39d3454c35 upstream.
Building with gcc 4.9.2 reveals a latent bug in the PCI accessors
for Footbridge platforms, which causes a fatal alignment fault
while accessing IO memory. Fix this by making the assembly volatile.
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d8d1dbefc upstream.
While addressing some warnings generated by -Warray-bounds, I found this
bug that was introduced back in 2017:
CC [M] fs/cifs/smb2pdu.o
fs/cifs/smb2pdu.c: In function ‘SMB2_negotiate’:
fs/cifs/smb2pdu.c:822:16: warning: array subscript 1 is above array bounds
of ‘__le16[1]’ {aka ‘short unsigned int[1]’} [-Warray-bounds]
822 | req->Dialects[1] = cpu_to_le16(SMB30_PROT_ID);
| ~~~~~~~~~~~~~^~~
fs/cifs/smb2pdu.c:823:16: warning: array subscript 2 is above array bounds
of ‘__le16[1]’ {aka ‘short unsigned int[1]’} [-Warray-bounds]
823 | req->Dialects[2] = cpu_to_le16(SMB302_PROT_ID);
| ~~~~~~~~~~~~~^~~
fs/cifs/smb2pdu.c:824:16: warning: array subscript 3 is above array bounds
of ‘__le16[1]’ {aka ‘short unsigned int[1]’} [-Warray-bounds]
824 | req->Dialects[3] = cpu_to_le16(SMB311_PROT_ID);
| ~~~~~~~~~~~~~^~~
fs/cifs/smb2pdu.c:816:16: warning: array subscript 1 is above array bounds
of ‘__le16[1]’ {aka ‘short unsigned int[1]’} [-Warray-bounds]
816 | req->Dialects[1] = cpu_to_le16(SMB302_PROT_ID);
| ~~~~~~~~~~~~~^~~
At the time, the size of array _Dialects_ was changed from 1 to 3 in struct
validate_negotiate_info_req, and then in 2019 it was changed from 3 to 4,
but those changes were never made in struct smb2_negotiate_req, which has
led to a 3 and a half years old out-of-bounds bug in function
SMB2_negotiate() (fs/cifs/smb2pdu.c).
Fix this by increasing the size of array _Dialects_ in struct
smb2_negotiate_req to 4.
Fixes: 9764c02fcb ("SMB3: Add support for multidialect negotiate (SMB2.1 and later)")
Fixes: d5c7076b77 ("smb3: add smb3.1.1 to default dialect list")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21b200d091 upstream.
Assuming
- //HOST/a is mounted on /mnt
- //HOST/b is mounted on /mnt/b
On a slow connection, running 'df' and killing it while it's
processing /mnt/b can make cifs_get_inode_info() returns -ERESTARTSYS.
This triggers the following chain of events:
=> the dentry revalidation fail
=> dentry is put and released
=> superblock associated with the dentry is put
=> /mnt/b is unmounted
This patch makes cifs_d_revalidate() return the error instead of 0
(invalid) when cifs_revalidate_dentry() fails, except for ENOENT (file
deleted) and ESTALE (file recreated).
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Suggested-by: Shyam Prasad N <nspmangalore@gmail.com>
Reviewed-by: Shyam Prasad N <nspmangalore@gmail.com>
CC: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4a6106354 upstream.
xhci driver may in some special cases need to copy small amounts
of payload data to a bounce buffer in order to meet the boundary
and alignment restrictions set by the xHCI specification.
In the majority of these cases the data is in a sg list, and
driver incorrectly assumed data is always in urb->sg when using
the bounce buffer.
If data instead is contiguous, and in urb->transfer_buffer, we may still
need to bounce buffer a small part if data starts very close (less than
packet size) to a 64k boundary.
Check if sg list is used before copying data to/from it.
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210203113702.436762-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0188b87899 upstream.
Our system encountered a re-init error when re-registering same kretprobe,
where the kretprobe_instance in rp->free_instances is illegally accessed
after re-init.
Implementation to avoid re-registration has been introduced for kprobe
before, but lags for register_kretprobe(). We must check if kprobe has
been re-registered before re-initializing kretprobe, otherwise it will
destroy the data struct of kretprobe registered, which can lead to memory
leak, system crash, also some unexpected behaviors.
We use check_kprobe_rereg() to check if kprobe has been re-registered
before running register_kretprobe()'s body, for giving a warning message
and terminate registration process.
Link: https://lkml.kernel.org/r/20210128124427.2031088-1-bobo.shaobowang@huawei.com
Cc: stable@vger.kernel.org
Fixes: 1f0ab40976 ("kprobes: Prevent re-registration of the same kprobe")
[ The above commit should have been done for kretprobes too ]
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Cheng Jian <cj.chengjian@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f670e9f9c8 upstream.
dwc2_hsotg_process_req_status uses ep_from_windex() to retrieve
the endpoint for the index provided in the wIndex request param.
In a test-case with a rndis gadget running and sending a malformed
packet to it like:
dev.ctrl_transfer(
0x82, # bmRequestType
0x00, # bRequest
0x0000, # wValue
0x0001, # wIndex
0x00 # wLength
)
it is possible to cause a crash:
[ 217.533022] dwc2 ff300000.usb: dwc2_hsotg_process_req_status: USB_REQ_GET_STATUS
[ 217.559003] Unable to handle kernel read from unreadable memory at virtual address 0000000000000088
...
[ 218.313189] Call trace:
[ 218.330217] ep_from_windex+0x3c/0x54
[ 218.348565] usb_gadget_giveback_request+0x10/0x20
[ 218.368056] dwc2_hsotg_complete_request+0x144/0x184
This happens because ep_from_windex wants to compare the endpoint
direction even if index_to_ep() didn't return an endpoint due to
the direction not matching.
The fix is easy insofar that the actual direction check is already
happening when calling index_to_ep() which will return NULL if there
is no endpoint for the targeted direction, so the offending check
can go away completely.
Fixes: c6f5c050e2 ("usb: dwc2: gadget: add bi-directional endpoint support")
Cc: stable@vger.kernel.org
Reported-by: Gerhard Klostermeier <gerhard.klostermeier@syss.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210127103919.58215-1-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 5018c59607 ]
Jesse and Ido reported the following race condition:
<CPU A, t0> - Received packet A is forwarded and cached dst entry is
taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set()
<t1> - Given Jesse has busy routers ("ingesting full BGP routing tables
from multiple ISPs"), route is added / deleted and rt_cache_flush() is
called
<CPU B, t2> - Received packet B tries to use the same cached dst entry
from t0, but rt_cache_valid() is no longer true and it is replaced in
rt_cache_route() by the newer one. This calls dst_dev_put() on the
original dst entry which assigns the blackhole netdev to 'dst->dev'
<CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due
to 'dst->dev' being the blackhole netdev
There are 2 issues in the v4 routing code:
1. A per-netns counter is used to do the validation of the route. That
means whenever a route is changed in the netns, users of all routes in
the netns needs to redo lookup. v6 has an implementation of only
updating fn_sernum for routes that are affected.
2. When rt_cache_valid() returns false, rt_cache_route() is called to
throw away the current cache, and create a new one. This seems
unnecessary because as long as this route does not change, the route
cache does not need to be recreated.
To fully solve the above 2 issues, it probably needs quite some code
changes and requires careful testing, and does not suite for net branch.
So this patch only tries to add the deleted cached rt into the uncached
list, so user could still be able to use it to receive packets until
it's done.
Fixes: 95c47f9cf5 ("ipv4: call dst_dev_put() properly")
Signed-off-by: Wei Wang <weiwan@google.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Reported-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Tested-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e81e072443 upstream.
When compiling the kernel with AS=clang, objtool produces a lot of
warnings:
warning: objtool: missing symbol for section .text
warning: objtool: missing symbol for section .init.text
warning: objtool: missing symbol for section .ref.text
It then fails to generate the ORC table.
The problem is that objtool assumes text section symbols always exist.
But the Clang assembler is aggressive about removing them.
When generating relocations for the ORC table, objtool always tries to
reference instructions by their section symbol offset. If the section
symbol doesn't exist, it bails.
Do a fallback: when a section symbol isn't available, reference a
function symbol instead.
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/669
Link: https://lkml.kernel.org/r/9a9cae7fcf628843aabe5a086b1a3c5bf50f42e8.1585761021.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88c7a9fd9b ]
When sending a packet, we will prepend it with an LAPB header.
This modifies the shared parts of a cloned skb, so we should copy the
skb rather than just clone it, before we prepend the header.
In "Documentation/networking/driver.rst" (the 2nd point), it states
that drivers shouldn't modify the shared parts of a cloned skb when
transmitting.
The "dev_queue_xmit_nit" function in "net/core/dev.c", which is called
when an skb is being sent, clones the skb and sents the clone to
AF_PACKET sockets. Because the LAPB drivers first remove a 1-byte
pseudo-header before handing over the skb to us, if we don't copy the
skb before prepending the LAPB header, the first byte of the packets
received on AF_PACKET sockets can be corrupted.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20210201055706.415842-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa880c6f3e ]
Dcfg was overlapping with clockgen address space which resulted
in failure in memory allocation for dcfg. According regs description
dcfg size should not be bigger than 4KB.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Fixes: 8126d88162 ("arm64: dts: add QorIQ LS1046A SoC support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac687e6e8c ]
There is a need to distinguish geniune per-cpu kthreads from kthreads
that happen to have a single CPU affinity.
Geniune per-cpu kthreads are kthreads that are CPU affine for
correctness, these will obviously have PF_KTHREAD set, but must also
have PF_NO_SETAFFINITY set, lest userspace modify their affinity and
ruins things.
However, these two things are not sufficient, PF_NO_SETAFFINITY is
also set on other tasks that have their affinities controlled through
other means, like for instance workqueues.
Therefore another bit is needed; it turns out kthread_create_per_cpu()
already has such a bit: KTHREAD_IS_PER_CPU, which is used to make
kthread_park()/kthread_unpark() work correctly.
Expose this flag and remove the implicit setting of it from
kthread_create_on_cpu(); the io_uring usage of it seems dubious at
best.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lkml.kernel.org/r/20210121103506.557620262@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d489151e9 ]
Thanks to a recent binutils change which doesn't generate unused
symbols, it's now possible for thunk_64.o be completely empty without
CONFIG_PREEMPTION: no text, no data, no symbols.
We could edit the Makefile to only build that file when
CONFIG_PREEMPTION is enabled, but that will likely create confusion
if/when the thunks end up getting used by some other code again.
Just ignore it and move on.
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1254
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764907293e ]
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b0f16fa6 ]
A race condition exists between the response handler getting called because
of exchange_mgr_reset() (which clears out all the active XIDs) and the
response we get via an interrupt.
Sequence of events:
rport ba0200: Port timeout, state PLOGI
rport ba0200: Port entered PLOGI state from PLOGI state
xid 1052: Exchange timer armed : 20000 msecs xid timer armed here
rport ba0200: Received LOGO request while in state PLOGI
rport ba0200: Delete port
rport ba0200: work event 3
rport ba0200: lld callback ev 3
bnx2fc: rport_event_hdlr: event = 3, port_id = 0xba0200
bnx2fc: ba0200 - rport not created Yet!!
/* Here we reset any outstanding exchanges before
freeing rport using the exch_mgr_reset() */
xid 1052: Exchange timer canceled
/* Here we got two responses for one xid */
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
Skip the response if the exchange is already completed.
Link: https://lore.kernel.org/r/20201215194731.2326-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764257d906 ]
On deferred probe, we will get the following splat:
cpcap-usb-phy cpcap-usb-phy.0: could not initialize VBUS or ID IIO: -517
WARNING: CPU: 0 PID: 21 at drivers/regulator/core.c:2123 regulator_put+0x68/0x78
...
(regulator_put) from [<c068ebf0>] (release_nodes+0x1b4/0x1fc)
(release_nodes) from [<c068a9a4>] (really_probe+0x104/0x4a0)
(really_probe) from [<c068b034>] (driver_probe_device+0x58/0xb4)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201230102105.11826-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3d1cf435e2 upstream
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81b704d3e4 upstream.
Calling acpi_thermal_check() from acpi_thermal_notify() directly
is problematic if _TMP triggers Notify () on the thermal zone for
which it has been evaluated (which happens on some systems), because
it causes a new acpi_thermal_notify() invocation to be queued up
every time and if that takes place too often, an indefinite number of
pending work items may accumulate in kacpi_notify_wq over time.
Besides, it is not really useful to queue up a new invocation of
acpi_thermal_check() if one of them is pending already.
For these reasons, rework acpi_thermal_notify() to queue up a thermal
check instead of calling acpi_thermal_check() directly and only allow
one thermal check to be pending at a time. Moreover, only allow one
acpi_thermal_check_fn() instance at a time to run
thermal_zone_device_update() for one thermal zone and make it return
early if it sees other instances running for the same thermal zone.
While at it, fold acpi_thermal_check() into acpi_thermal_check_fn(),
as it is only called from there after the other changes made here.
[This issue appears to have been exposed by commit 6d25be5782
("sched/core, workqueues: Distangle worker accounting from rq
lock"), but it is unclear why it was not visible earlier.]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208877
Reported-by: Stephen Berman <stephen.berman@gmx.net>
Diagnosed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Stephen Berman <stephen.berman@gmx.net>
Cc: All applicable <stable@vger.kernel.org>
[bigeasy: Backported to v5.4.y]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62d9f1a694 upstream.
Upon receiving a cumulative ACK that changes the congestion state from
Disorder to Open, the TLP timer is not set. If the sender is app-limited,
it can only wait for the RTO timer to expire and retransmit.
The reason for this is that the TLP timer is set before the congestion
state changes in tcp_ack(), so we delay the time point of calling
tcp_set_xmit_timer() until after tcp_fastretrans_alert() returns and
remove the FLAG_SET_XMIT_TIMER from ack_flag when the RACK reorder timer
is set.
This commit has two additional benefits:
1) Make sure to reset RTO according to RFC6298 when receiving ACK, to
avoid spurious RTO caused by RTO timer early expires.
2) Reduce the xmit timer reschedule once per ACK when the RACK reorder
timer is set.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Link: https://lore.kernel.org/netdev/1611311242-6675-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1611464834-23030-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0947d0d21 upstream.
Function __team_compute_features() is protected by team->lock
mutex when it is called from team_compute_features() used when
features of an underlying device is changed. This causes
a deadlock when NETDEV_FEAT_CHANGE notifier for underlying device
is fired due to change propagated from team driver (e.g. MTU
change). It's because callbacks like team_change_mtu() or
team_vlan_rx_{add,del}_vid() protect their port list traversal
by team->lock mutex.
Example (r8169 case where this driver disables TSO for certain MTU
values):
...
[ 6391.348202] __mutex_lock.isra.6+0x2d0/0x4a0
[ 6391.358602] team_device_event+0x9d/0x160 [team]
[ 6391.363756] notifier_call_chain+0x47/0x70
[ 6391.368329] netdev_update_features+0x56/0x60
[ 6391.373207] rtl8169_change_mtu+0x14/0x50 [r8169]
[ 6391.378457] dev_set_mtu_ext+0xe1/0x1d0
[ 6391.387022] dev_set_mtu+0x52/0x90
[ 6391.390820] team_change_mtu+0x64/0xf0 [team]
[ 6391.395683] dev_set_mtu_ext+0xe1/0x1d0
[ 6391.399963] do_setlink+0x231/0xf50
...
In fact team_compute_features() called from team_device_event()
does not need to be protected by team->lock mutex and rcu_read_lock()
is sufficient there for port list traversal.
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Cc: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20210125074416.4056484-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9def3b1a07 upstream.
Since commit c40aaaac10 ("iommu/vt-d: Gracefully handle DMAR units
with no supported address widths") dmar.c needs struct iommu_device to
be selected. We can drop this dependency by not dereferencing struct
iommu_device if IOMMU_API is not selected and by reusing the information
stored in iommu->drhd->ignored instead.
This fixes the following build error when IOMMU_API is not selected:
drivers/iommu/dmar.c: In function ‘free_iommu’:
drivers/iommu/dmar.c:1139:41: error: ‘struct iommu_device’ has no member named ‘ops’
1139 | if (intel_iommu_enabled && iommu->iommu.ops) {
^
Fixes: c40aaaac10 ("iommu/vt-d: Gracefully handle DMAR units with no supported address widths")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20201013073055.11262-1-brgl@bgdev.pl
Signed-off-by: Joerg Roedel <jroedel@suse.de>
[ - context change due to moving drivers/iommu/dmar.c to
drivers/iommu/intel/dmar.c
- set the drhr in the iommu like in upstream commit b1012ca8dc
("iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu") ]
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bb2610bc4 upstream.
32-bit user code that uses int $80 doesn't care about r8-r11. There is,
however, some 64-bit user code that intentionally uses int $0x80 to invoke
32-bit system calls. From what I've seen, basically all such code assumes
that r8-r15 are all preserved, but the kernel clobbers r8-r11. Since I
doubt that there's any code that depends on int $0x80 zeroing r8-r11,
change the kernel to preserve them.
I suspect that very little user code is broken by the old clobber, since
r8-r11 are only rarely allocated by gcc, and they're clobbered by function
calls, so they only way we'd see a problem is if the same function that
invokes int $0x80 also spills something important to one of these
registers.
The current behavior seems to date back to the historical commit
"[PATCH] x86-64 merge for 2.6.4". Before that, all regs were
preserved. I can't find any explanation of why this change was made.
Update the test_syscall_vdso_32 testcase as well to verify the new
behavior, and it strengthens the test to make sure that the kernel doesn't
accidentally permute r8..r15.
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Link: https://lkml.kernel.org/r/d4c4d9985fbe64f8c9e19291886453914b48caee.1523975710.git.luto@kernel.org
Signed-off-by: Alistair Delva <adelva@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d372c4edf ]
If we spin for a long time in memory reads that (for some reason in
hardware) take a long time, then we'll eventually get messages such
as
watchdog: BUG: soft lockup - CPU#2 stuck for 24s! [kworker/2:2:272]
This is because the reading really does take a very long time, and
we don't schedule, so we're hogging the CPU with this task, at least
if CONFIG_PREEMPT is not set, e.g. with CONFIG_PREEMPT_VOLUNTARY=y.
Previously I misinterpreted the situation and thought that this was
only going to happen if we had interrupts disabled, and then fixed
this (which is good anyway, however), but that didn't always help;
looking at it again now I realized that the spin unlock will only
reschedule if CONFIG_PREEMPT is used.
In order to avoid this issue, change the code to cond_resched() if
we've been spinning for too long here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 04516706bb ("iwlwifi: pcie: limit memory read spin time")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130253.217a9d6a6a12.If964cb582ab0aaa94e81c4ff3b279eaafda0fd3f@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56ce7c25ae ]
When setting xfrm replay_window to values higher than 32, a rare
page-fault occurs in xfrm_replay_advance_bmp:
BUG: unable to handle page fault for address: ffff8af350ad7920
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD ad001067 P4D ad001067 PUD 0
Oops: 0002 [#1] SMP PTI
CPU: 3 PID: 30 Comm: ksoftirqd/3 Kdump: loaded Not tainted 5.4.52-050452-generic #202007160732
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
RIP: 0010:xfrm_replay_advance_bmp+0xbb/0x130
RSP: 0018:ffffa1304013ba40 EFLAGS: 00010206
RAX: 000000000000010d RBX: 0000000000000002 RCX: 00000000ffffff4b
RDX: 0000000000000018 RSI: 00000000004c234c RDI: 00000000ffb3dbff
RBP: ffffa1304013ba50 R08: ffff8af330ad7920 R09: 0000000007fffffa
R10: 0000000000000800 R11: 0000000000000010 R12: ffff8af29d6258c0
R13: ffff8af28b95c700 R14: 0000000000000000 R15: ffff8af29d6258fc
FS: 0000000000000000(0000) GS:ffff8af339ac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff8af350ad7920 CR3: 0000000015ee4000 CR4: 00000000001406e0
Call Trace:
xfrm_input+0x4e5/0xa10
xfrm4_rcv_encap+0xb5/0xe0
xfrm4_udp_encap_rcv+0x140/0x1c0
Analysis revealed offending code is when accessing:
replay_esn->bmp[nr] |= (1U << bitnr);
with 'nr' being 0x07fffffa.
This happened in an SMP system when reordering of packets was present;
A packet arrived with a "too old" sequence number (outside the window,
i.e 'diff > replay_window'), and therefore the following calculation:
bitnr = replay_esn->replay_window - (diff - pos);
yields a negative result, but since bitnr is u32 we get a large unsigned
quantity (in crash dump above: 0xffffff4b seen in ecx).
This was supposed to be protected by xfrm_input()'s former call to:
if (x->repl->check(x, skb, seq)) {
However, the state's spinlock x->lock is *released* after '->check()'
is performed, and gets re-acquired before '->advance()' - which gives a
chance for a different core to update the xfrm state, e.g. by advancing
'replay_esn->seq' when it encounters more packets - leading to a
'diff > replay_window' situation when original core continues to
xfrm_replay_advance_bmp().
An attempt to fix this issue was suggested in commit bcf66bf54a
("xfrm: Perform a replay check after return from async codepaths"),
by calling 'x->repl->recheck()' after lock is re-acquired, but fix
applied only to asyncronous crypto algorithms.
Augment the fix, by *always* calling 'recheck()' - irrespective if we're
using async crypto.
Fixes: 0ebea8ef35 ("[IPSEC]: Move state lock into x->type->input")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0c5b7a501e upstream.
Otherwise, the newly create element shows no timeout when listing the
ruleset. If the set definition does not specify a default timeout, then
the set element only shows the expiration time, but not the timeout.
This is a problem when restoring a stateful ruleset listing since it
skips the timeout policy entirely.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a88afa46b8 upstream.
When the kernel is configured to use the Thumb-2 instruction set
"suspend-to-memory" fails to resume. Observed on a Colibri iMX6ULL
(i.MX 6ULL) and Apalis iMX6 (i.MX 6Q).
It looks like the CPU resumes unconditionally in ARM instruction mode
and then chokes on the presented Thumb-2 code it should execute.
Fix this by using the arm instruction set for all code in
suspend-imx6.S.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Fixes: df595746fa ("ARM: imx: add suspend in ocram support for i.mx6q")
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0549cd67b0 upstream.
This is inline with the specification described in blkif.h:
* discard-granularity: should be set to the physical block size if
node is not present.
* discard-alignment, discard-secure: should be set to 0 if node not
present.
This was detected as QEMU would only create the discard-granularity
node but not discard-alignment, and thus the setup done in
blkfront_setup_discard would fail.
Fix blkfront_setup_discard to not fail on missing nodes, and also fix
blkif_set_queue_limits to set the discard granularity to the physical
block size if none is specified in xenbus.
Fixes: ed30bf317c ('xen-blkfront: Handle discard requests.')
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Tested-By: Arthur Borsboom <arthurborsboom@gmail.com>
Link: https://lore.kernel.org/r/20210119105727.95173-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27af8e2c90 upstream.
We have the following potential deadlock condition:
========================================================
WARNING: possible irq lock inversion dependency detected
5.10.0-rc2+ #25 Not tainted
--------------------------------------------------------
swapper/3/0 just changed the state of lock:
ffff8880063bd618 (&host->lock){-...}-{2:2}, at: ata_bmdma_interrupt+0x27/0x200
but this lock took another, HARDIRQ-READ-unsafe lock in the past:
(&trig->leddev_list_lock){.+.?}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&trig->leddev_list_lock);
local_irq_disable();
lock(&host->lock);
lock(&trig->leddev_list_lock);
<Interrupt>
lock(&host->lock);
*** DEADLOCK ***
no locks held by swapper/3/0.
the shortest dependencies between 2nd lock and 1st lock:
-> (&trig->leddev_list_lock){.+.?}-{2:2} ops: 46 {
HARDIRQ-ON-R at:
lock_acquire+0x15f/0x420
_raw_read_lock+0x42/0x90
led_trigger_event+0x2b/0x70
rfkill_global_led_trigger_worker+0x94/0xb0
process_one_work+0x240/0x560
worker_thread+0x58/0x3d0
kthread+0x151/0x170
ret_from_fork+0x1f/0x30
IN-SOFTIRQ-R at:
lock_acquire+0x15f/0x420
_raw_read_lock+0x42/0x90
led_trigger_event+0x2b/0x70
kbd_bh+0x9e/0xc0
tasklet_action_common.constprop.0+0xe9/0x100
tasklet_action+0x22/0x30
__do_softirq+0xcc/0x46d
run_ksoftirqd+0x3f/0x70
smpboot_thread_fn+0x116/0x1f0
kthread+0x151/0x170
ret_from_fork+0x1f/0x30
SOFTIRQ-ON-R at:
lock_acquire+0x15f/0x420
_raw_read_lock+0x42/0x90
led_trigger_event+0x2b/0x70
rfkill_global_led_trigger_worker+0x94/0xb0
process_one_work+0x240/0x560
worker_thread+0x58/0x3d0
kthread+0x151/0x170
ret_from_fork+0x1f/0x30
INITIAL READ USE at:
lock_acquire+0x15f/0x420
_raw_read_lock+0x42/0x90
led_trigger_event+0x2b/0x70
rfkill_global_led_trigger_worker+0x94/0xb0
process_one_work+0x240/0x560
worker_thread+0x58/0x3d0
kthread+0x151/0x170
ret_from_fork+0x1f/0x30
}
... key at: [<ffffffff83da4c00>] __key.0+0x0/0x10
... acquired at:
_raw_read_lock+0x42/0x90
led_trigger_blink_oneshot+0x3b/0x90
ledtrig_disk_activity+0x3c/0xa0
ata_qc_complete+0x26/0x450
ata_do_link_abort+0xa3/0xe0
ata_port_freeze+0x2e/0x40
ata_hsm_qc_complete+0x94/0xa0
ata_sff_hsm_move+0x177/0x7a0
ata_sff_pio_task+0xc7/0x1b0
process_one_work+0x240/0x560
worker_thread+0x58/0x3d0
kthread+0x151/0x170
ret_from_fork+0x1f/0x30
-> (&host->lock){-...}-{2:2} ops: 69 {
IN-HARDIRQ-W at:
lock_acquire+0x15f/0x420
_raw_spin_lock_irqsave+0x52/0xa0
ata_bmdma_interrupt+0x27/0x200
__handle_irq_event_percpu+0xd5/0x2b0
handle_irq_event+0x57/0xb0
handle_edge_irq+0x8c/0x230
asm_call_irq_on_stack+0xf/0x20
common_interrupt+0x100/0x1c0
asm_common_interrupt+0x1e/0x40
native_safe_halt+0xe/0x10
arch_cpu_idle+0x15/0x20
default_idle_call+0x59/0x1c0
do_idle+0x22c/0x2c0
cpu_startup_entry+0x20/0x30
start_secondary+0x11d/0x150
secondary_startup_64_no_verify+0xa6/0xab
INITIAL USE at:
lock_acquire+0x15f/0x420
_raw_spin_lock_irqsave+0x52/0xa0
ata_dev_init+0x54/0xe0
ata_link_init+0x8b/0xd0
ata_port_alloc+0x1f1/0x210
ata_host_alloc+0xf1/0x130
ata_host_alloc_pinfo+0x14/0xb0
ata_pci_sff_prepare_host+0x41/0xa0
ata_pci_bmdma_prepare_host+0x14/0x30
piix_init_one+0x21f/0x600
local_pci_probe+0x48/0x80
pci_device_probe+0x105/0x1c0
really_probe+0x221/0x490
driver_probe_device+0xe9/0x160
device_driver_attach+0xb2/0xc0
__driver_attach+0x91/0x150
bus_for_each_dev+0x81/0xc0
driver_attach+0x1e/0x20
bus_add_driver+0x138/0x1f0
driver_register+0x91/0xf0
__pci_register_driver+0x73/0x80
piix_init+0x1e/0x2e
do_one_initcall+0x5f/0x2d0
kernel_init_freeable+0x26f/0x2cf
kernel_init+0xe/0x113
ret_from_fork+0x1f/0x30
}
... key at: [<ffffffff83d9fdc0>] __key.6+0x0/0x10
... acquired at:
__lock_acquire+0x9da/0x2370
lock_acquire+0x15f/0x420
_raw_spin_lock_irqsave+0x52/0xa0
ata_bmdma_interrupt+0x27/0x200
__handle_irq_event_percpu+0xd5/0x2b0
handle_irq_event+0x57/0xb0
handle_edge_irq+0x8c/0x230
asm_call_irq_on_stack+0xf/0x20
common_interrupt+0x100/0x1c0
asm_common_interrupt+0x1e/0x40
native_safe_halt+0xe/0x10
arch_cpu_idle+0x15/0x20
default_idle_call+0x59/0x1c0
do_idle+0x22c/0x2c0
cpu_startup_entry+0x20/0x30
start_secondary+0x11d/0x150
secondary_startup_64_no_verify+0xa6/0xab
This lockdep splat is reported after:
commit e918188611 ("locking: More accurate annotations for read_lock()")
To clarify:
- read-locks are recursive only in interrupt context (when
in_interrupt() returns true)
- after acquiring host->lock in CPU1, another cpu (i.e. CPU2) may call
write_lock(&trig->leddev_list_lock) that would be blocked by CPU0
that holds trig->leddev_list_lock in read-mode
- when CPU1 (ata_ac_complete()) tries to read-lock
trig->leddev_list_lock, it would be blocked by the write-lock waiter
on CPU2 (because we are not in interrupt context, so the read-lock is
not recursive)
- at this point if an interrupt happens on CPU0 and
ata_bmdma_interrupt() is executed it will try to acquire host->lock,
that is held by CPU1, that is currently blocked by CPU2, so:
* CPU0 blocked by CPU1
* CPU1 blocked by CPU2
* CPU2 blocked by CPU0
*** DEADLOCK ***
The deadlock scenario is better represented by the following schema
(thanks to Boqun Feng <boqun.feng@gmail.com> for the schema and the
detailed explanation of the deadlock condition):
CPU 0: CPU 1: CPU 2:
----- ----- -----
led_trigger_event():
read_lock(&trig->leddev_list_lock);
<workqueue>
ata_hsm_qc_complete():
spin_lock_irqsave(&host->lock);
write_lock(&trig->leddev_list_lock);
ata_port_freeze():
ata_do_link_abort():
ata_qc_complete():
ledtrig_disk_activity():
led_trigger_blink_oneshot():
read_lock(&trig->leddev_list_lock);
// ^ not in in_interrupt() context, so could get blocked by CPU 2
<interrupt>
ata_bmdma_interrupt():
spin_lock_irqsave(&host->lock);
Fix by using read_lock_irqsave/irqrestore() in led_trigger_event(), so
that no interrupt can happen in between, preventing the deadlock
condition.
Apply the same change to led_trigger_blink_setup() as well, since the
same deadlock scenario can also happen in power_supply_update_bat_leds()
-> led_trigger_blink() -> led_trigger_blink_setup() (workqueue context),
and potentially prevent other similar usages.
Link: https://lore.kernel.org/lkml/20201101092614.GB3989@xps-13-7390/
Fixes: eb25cb9956 ("leds: convert IDE trigger to common disk trigger")
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f46400f7a upstream.
In commit 3499ba8198 ("xen: Fix event channel callback via INTX/GSI")
I reworked the triggering of xenbus_probe().
I tried to simplify things by taking out the workqueue based startup
triggered from wake_waiting(); the somewhat poorly named xenbus IRQ
handler.
I missed the fact that in the XS_LOCAL case (Dom0 starting its own
xenstored or xenstore-stubdom, which happens after the kernel is booted
completely), that IRQ-based trigger is still actually needed.
So... put it back, except more cleanly. By just spawning a xenbus_probe
thread which waits on xb_waitq and runs the probe the first time it
gets woken, just as the workqueue-based hack did.
This is actually a nicer approach for *all* the back ends with different
interrupt methods, and we can switch them all over to that without the
complex conditions for when to trigger it. But not in -rc6. This is
the minimal fix for the regression, although it's a step in the right
direction instead of doing a partial revert and actually putting the
workqueue back. It's also simpler than the workqueue.
Fixes: 3499ba8198 ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/4c9af052a6e0f6485d1de43f2c38b1461996db99.camel@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Cc: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f7becf1b7 upstream.
The injection process of smi has two steps:
Qemu KVM
Step1:
cpu->interrupt_request &= \
~CPU_INTERRUPT_SMI;
kvm_vcpu_ioctl(cpu, KVM_SMI)
call kvm_vcpu_ioctl_smi() and
kvm_make_request(KVM_REQ_SMI, vcpu);
Step2:
kvm_vcpu_ioctl(cpu, KVM_RUN, 0)
call process_smi() if
kvm_check_request(KVM_REQ_SMI, vcpu) is
true, mark vcpu->arch.smi_pending = true;
The vcpu->arch.smi_pending will be set true in step2, unfortunately if
vcpu paused between step1 and step2, the kvm_run->immediate_exit will be
set and vcpu has to exit to Qemu immediately during step2 before mark
vcpu->arch.smi_pending true.
During VM migration, Qemu will get the smi pending status from KVM using
KVM_GET_VCPU_EVENTS ioctl at the downtime, then the smi pending status
will be lost.
Signed-off-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Shengen Zhuang <zhuangshengen@huawei.com>
Message-Id: <20210118084720.1585-1-jianjay.zhou@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6808965568 upstream.
of_match_node() calls __of_match_node() which loops though the entries of
matches array. It stops when condition:
(matches->name[0] || matches->type[0] || matches->compatible[0]) is
false. Thus, add a null entry at the end of at91_soc_allowed_list[]
array.
Fixes: caab13b496 ("drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs")
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36af2d5c44 upstream.
Commit 8765c5ba19 ("ACPI / scan: Rework modalias creation when
"compatible" is present") may create two "MODALIAS=" in one uevent
file if specific conditions are met.
This breaks systemd-udevd, which assumes each "key" in one uevent file
to be unique. The internal implementation of systemd-udevd overwrites
the first MODALIAS with the second one, so its kmod rule doesn't load
the driver for the first MODALIAS.
So if both the ACPI modalias and the OF modalias are present, use the
latter to ensure that there will be only one MODALIAS.
Link: https://github.com/systemd/systemd/pull/18163
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fixes: 8765c5ba19 ("ACPI / scan: Rework modalias creation when "compatible" is present")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b98e762e3d upstream.
When setting up a device, we can krealloc the config->socks array to add
new sockets to the configuration. However if we happen to get a IO
request in at this point even though we aren't setup we could hit a UAF,
as we deref config->socks without any locking, assuming that the
configuration was setup already and that ->socks is safe to access it as
we have a reference on the configuration.
But there's nothing really preventing IO from occurring at this point of
the device setup, we don't want to incur the overhead of a lock to
access ->socks when it will never change while the device is running.
To fix this UAF scenario simply freeze the queue if we are adding
sockets. This will protect us from this particular case without adding
any additional overhead for the normal running case.
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e249cb5b7 upstream.
When lazytime is enabled and an inode is being written due to its
in-memory updated timestamps having expired, either due to a sync() or
syncfs() system call or due to dirtytime_expire_interval having elapsed,
the VFS needs to inform the filesystem so that the filesystem can copy
the inode's timestamps out to the on-disk data structures.
This is done by __writeback_single_inode() calling
mark_inode_dirty_sync(), which then calls ->dirty_inode(I_DIRTY_SYNC).
However, this occurs after __writeback_single_inode() has already
cleared the dirty flags from ->i_state. This causes two bugs:
- mark_inode_dirty_sync() redirties the inode, causing it to remain
dirty. This wastefully causes the inode to be written twice. But
more importantly, it breaks cases where sync_filesystem() is expected
to clean dirty inodes. This includes the FS_IOC_REMOVE_ENCRYPTION_KEY
ioctl (as reported at
https://lore.kernel.org/r/20200306004555.GB225345@gmail.com), as well
as possibly filesystem freezing (freeze_super()).
- Since ->i_state doesn't contain I_DIRTY_TIME when ->dirty_inode() is
called from __writeback_single_inode() for lazytime expiration,
xfs_fs_dirty_inode() ignores the notification. (XFS only cares about
lazytime expirations, and it assumes that i_state will contain
I_DIRTY_TIME during those.) Therefore, lazy timestamps aren't
persisted by sync(), syncfs(), or dirtytime_expire_interval on XFS.
Fix this by moving the call to mark_inode_dirty_sync() to earlier in
__writeback_single_inode(), before the dirty flags are cleared from
i_state. This makes filesystems be properly notified of the timestamp
expiration, and it avoids incorrectly redirtying the inode.
This fixes xfstest generic/580 (which tests
FS_IOC_REMOVE_ENCRYPTION_KEY) when run on ext4 or f2fs with lazytime
enabled. It also fixes the new lazytime xfstest I've proposed, which
reproduces the above-mentioned XFS bug
(https://lore.kernel.org/r/20210105005818.92978-1-ebiggers@kernel.org).
Alternatively, we could call ->dirty_inode(I_DIRTY_SYNC) directly. But
due to the introduction of I_SYNC_QUEUED, mark_inode_dirty_sync() is the
right thing to do because mark_inode_dirty_sync() now knows not to move
the inode to a writeback list if it is currently queued for sync.
Fixes: 0ae45f63d4 ("vfs: add support for a lazytime mount option")
Cc: stable@vger.kernel.org
Depends-on: 5afced3bf2 ("writeback: Avoid skipping inode writeback")
Link: https://lore.kernel.org/r/20210112190253.64307-2-ebiggers@kernel.org
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fcd57505c upstream.
The only use of I_DIRTY_TIME_EXPIRE is to detect in
__writeback_single_inode() that inode got there because flush worker
decided it's time to writeback the dirty inode time stamps (either
because we are syncing or because of age). However we can detect this
directly in __writeback_single_inode() and there's no need for the
strange propagation with I_DIRTY_TIME_EXPIRE flag.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09e43968db upstream.
The x86-64 psABI [0] specifies special relocation types
(R_X86_64_[REX_]GOTPCRELX) for indirection through the Global Offset
Table, semantically equivalent to R_X86_64_GOTPCREL, which the linker
can take advantage of for optimization (relaxation) at link time. This
is supported by LLD and binutils versions 2.26 onwards.
The compressed kernel is position-independent code, however, when using
LLD or binutils versions before 2.27, it must be linked without the -pie
option. In this case, the linker may optimize certain instructions into
a non-position-independent form, by converting foo@GOTPCREL(%rip) to $foo.
This potential issue has been present with LLD and binutils-2.26 for a
long time, but it has never manifested itself before now:
- LLD and binutils-2.26 only relax
movq foo@GOTPCREL(%rip), %reg
to
leaq foo(%rip), %reg
which is still position-independent, rather than
mov $foo, %reg
which is permitted by the psABI when -pie is not enabled.
- GCC happens to only generate GOTPCREL relocations on mov instructions.
- CLang does generate GOTPCREL relocations on non-mov instructions, but
when building the compressed kernel, it uses its integrated assembler
(due to the redefinition of KBUILD_CFLAGS dropping -no-integrated-as),
which has so far defaulted to not generating the GOTPCRELX
relocations.
Nick Desaulniers reports [1,2]:
"A recent change [3] to a default value of configuration variable
(ENABLE_X86_RELAX_RELOCATIONS OFF -> ON) in LLVM now causes Clang's
integrated assembler to emit R_X86_64_GOTPCRELX/R_X86_64_REX_GOTPCRELX
relocations. LLD will relax instructions with these relocations based
on whether the image is being linked as position independent or not.
When not, then LLD will relax these instructions to use absolute
addressing mode (R_RELAX_GOT_PC_NOPIC). This causes kernels built with
Clang and linked with LLD to fail to boot."
Patch series [4] is a solution to allow the compressed kernel to be
linked with -pie unconditionally, but even if merged is unlikely to be
backported. As a simple solution that can be applied to stable as well,
prevent the assembler from generating the relaxed relocation types using
the -mrelax-relocations=no option. For ease of backporting, do this
unconditionally.
[0] https://gitlab.com/x86-psABIs/x86-64-ABI/-/blob/master/x86-64-ABI/linker-optimization.tex#L65
[1] https://lore.kernel.org/lkml/20200807194100.3570838-1-ndesaulniers@google.com/
[2] https://github.com/ClangBuiltLinux/linux/issues/1121
[3] https://reviews.llvm.org/rGc41a18cf61790fc898dcda1055c3efbf442c14c0
[4] https://lore.kernel.org/lkml/20200731202738.2577854-1-nivedita@alum.mit.edu/
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200812004308.1448603-1-nivedita@alum.mit.edu
[nc: Backport to 4.14]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbeb97464e upstream.
Below race can come, if trace_open and resize of
cpu buffer is running parallely on different cpus
CPUX CPUY
ring_buffer_resize
atomic_read(&buffer->resize_disabled)
tracing_open
tracing_reset_online_cpus
ring_buffer_reset_cpu
rb_reset_cpu
rb_update_pages
remove/insert pages
resetting pointer
This race can cause data abort or some times infinte loop in
rb_remove_pages and rb_insert_pages while checking pages
for sanity.
Take buffer lock to fix this.
Link: https://lkml.kernel.org/r/1601976833-24377-1-git-send-email-gkohli@codeaurora.org
Cc: stable@vger.kernel.org
Fixes: 83f40318da ("ring-buffer: Make removal of ring buffer pages atomic")
Reported-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Gaurav Kohli <gkohli@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34b1a1ce14 upstream
fixup_pi_state_owner() tries to ensure that the state of the rtmutex,
pi_state and the user space value related to the PI futex are consistent
before returning to user space. In case that the user space value update
faults and the fault cannot be resolved by faulting the page in via
fault_in_user_writeable() the function returns with -EFAULT and leaves
the rtmutex and pi_state owner state inconsistent.
A subsequent futex_unlock_pi() operates on the inconsistent pi_state and
releases the rtmutex despite not owning it which can corrupt the RB tree of
the rtmutex and cause a subsequent kernel stack use after free.
It was suggested to loop forever in fixup_pi_state_owner() if the fault
cannot be resolved, but that results in runaway tasks which is especially
undesired when the problem happens due to a programming error and not due
to malice.
As the user space value cannot be fixed up, the proper solution is to make
the rtmutex and the pi_state consistent so both have the same owner. This
leaves the user space value out of sync. Any subsequent operation on the
futex will fail because the 10th rule of PI futexes (pi_state owner and
user space value are consistent) has been violated.
As a consequence this removes the inept attempts of 'fixing' the situation
in case that the current task owns the rtmutex when returning with an
unresolvable fault by unlocking the rtmutex which left pi_state::owner and
rtmutex::owner out of sync in a different and only slightly less dangerous
way.
Fixes: 1b7558e457 ("futexes: fix fault handling in futex_lock_pi")
Reported-by: gzobqq@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5cade200a upstream
Updating pi_state::owner is done at several places with the same
code. Provide a function for it and use that at the obvious places.
This is also a preparation for a bug fix to avoid yet another copy of the
same code or alternatively introducing a completely unpenetratable mess of
gotos.
Originally-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b79c5520 upstream
If that unexpected case of inconsistent arguments ever happens then the
futex state is left completely inconsistent and the printk is not really
helpful. Replace it with a warning and make the state consistent.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12bb3f7f1b upstream
In case that futex_lock_pi() was aborted by a signal or a timeout and the
task returned without acquiring the rtmutex, but is the designated owner of
the futex due to a concurrent futex_unlock_pi() fixup_owner() is invoked to
establish consistent state. In that case it invokes fixup_pi_state_owner()
which in turn tries to acquire the rtmutex again. If that succeeds then it
does not propagate this success to fixup_owner() and futex_lock_pi()
returns -EINTR or -ETIMEOUT despite having the futex locked.
Return success from fixup_pi_state_owner() in all cases where the current
task owns the rtmutex and therefore the futex and propagate it correctly
through fixup_owner(). Fixup the other callsite which does not expect a
positive return value.
Fixes: c1e2f0eaf0 ("futex: Avoid violating the 10th rule of futex")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 757fed1d08 upstream.
This reverts commit dde3c6b72a.
syzbot report a double-free bug. The following case can cause this bug.
- mm/slab_common.c: create_cache(): if the __kmem_cache_create() fails,
it does:
out_free_cache:
kmem_cache_free(kmem_cache, s);
- but __kmem_cache_create() - at least for slub() - will have done
sysfs_slab_add(s)
-> sysfs_create_group() .. fails ..
-> kobject_del(&s->kobj); .. which frees s ...
We can't remove the kmem_cache_free() in create_cache(), because other
error cases of __kmem_cache_create() do not free this.
So, revert the commit dde3c6b72a ("mm/slub: fix a memory leak in
sysfs_slab_add()") to fix this.
Reported-by: syzbot+d0bd96b4696c1ef67991@syzkaller.appspotmail.com
Fixes: dde3c6b72a ("mm/slub: fix a memory leak in sysfs_slab_add()")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d70ef22892 upstream.
sign_extend32 counts the sign bit parameter from 0, not from 1. So we
have to use "11" for 12th bit, not "12".
This mistake means we have not allowed negative op and cmp args since
commit 30d6e0a419 ("futex: Remove duplicated code and fix undefined
behaviour") till now.
Fixes: 30d6e0a419 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a826b04303 upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d2b51b008 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes: bc044e8db7 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c556025d upstream.
Commit 3226b158e6 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/20210114235423.232737-1-alobakin@pm.me
Fixes: a1c7fff7e1 ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f477a538c1 upstream.
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed7
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
Fixes: d8902adcc1 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5a6266fb upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes: 8f97339d3f ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7e0c3c29 upstream.
Occasionally, we are seeing some SuperSpeed devices resumes right after
being directed to U3. This commits add 500us delay to ensure LFPS
detector is disabled before sending ACK to firmware.
[ 16.099363] tegra-xusb 70090000.usb: entering ELPG
[ 16.104343] tegra-xusb 70090000.usb: 2-1 isn't suspended: 0x0c001203
[ 16.114576] tegra-xusb 70090000.usb: not all ports suspended: -16
[ 16.120789] tegra-xusb 70090000.usb: entering ELPG failed
The register write passes through a few flop stages of 32KHz clock domain.
NVIDIA ASIC designer reviewed RTL and suggests 500us delay.
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 576667bad3 upstream.
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
Cc: <stable@vger.kernel.org>
Tested-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210115161907.2875631-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 643a4df7fe upstream.
The system that use Synopsys USB host controllers goes to suspend
when using USB audio player. This causes the USB host controller
continuous send interrupt signal to system, When the number of
interrupts exceeds 100000, the system will forcibly close the
interrupts and output a calltrace error.
When the system goes to suspend, the last interrupt is reported to
the driver. At this time, the system has set the state to suspend.
This causes the last interrupt to not be processed by the system and
not clear the interrupt flag. This uncleared interrupt flag constantly
triggers new interrupt event. This causing the driver to receive more
than 100,000 interrupts, which causes the system to forcibly close the
interrupt report and report the calltrace error.
so, when the driver goes to sleep and changes the system state to
suspend, the interrupt flag needs to be cleared.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1610416647-45774-1-git-send-email-liulongfang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 599b3063ad upstream.
Since commit 5556797662 ("genirq/irqdomain: Allow partial trimming of
irq_data hierarchy") the irq_data chain is valided.
The irq_domain_trim_hierarchy() function doesn't consider the irq + ipi
domain hierarchy as valid, since the ipi domain has the irq domain set
as parent, but the parent domain has no chip set. Hence the boot ends in
a kernel panic.
Set the chip for the parent domain as it is done in the mips gic irq
driver, to have a valid irq_data chain.
Fixes: 3838a547fd ("irqchip: mips-cpu: Introduce IPI IRQ domain support")
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210107213603.1637781-1-dev@kresin.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b2cfa2d1d ]
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337 ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e05e06cd34 ]
Whatever it is that we were doing before doesn't work on Ampere.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 402a89660e ]
This issue has generally been covered up by the presence of additional
expansion ROMs after the ones we're interested in, with header fetches
of subsequent images loading enough of the ROM to hide the issue.
Noticed on GA102, which lacks a type 0x70 image compared to TU102,.
[ 906.364197] nouveau 0000:09:00.0: bios: 00000000: type 00, 65024 bytes
[ 906.381205] nouveau 0000:09:00.0: bios: 0000fe00: type 03, 91648 bytes
[ 906.405213] nouveau 0000:09:00.0: bios: 00026400: type e0, 22016 bytes
[ 906.410984] nouveau 0000:09:00.0: bios: 0002ba00: type e0, 366080 bytes
vs
[ 22.961901] nouveau 0000:09:00.0: bios: 00000000: type 00, 60416 bytes
[ 22.984174] nouveau 0000:09:00.0: bios: 0000ec00: type 03, 71168 bytes
[ 23.010446] nouveau 0000:09:00.0: bios: 00020200: type e0, 48128 bytes
[ 23.028220] nouveau 0000:09:00.0: bios: 0002be00: type e0, 140800 bytes
[ 23.080196] nouveau 0000:09:00.0: bios: 0004e400: type 70, 7168 bytes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3499ba8198 ]
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 809b1e4945 upstream.
This reverts commit
644bda6f34 ("dm table: fall back to getting device using name_to_dev_t()")
dm_get_dev_t() is just used to convert an arbitrary 'path' string
into a dev_t. It doesn't presume that the device is present; that
check will be done later, as the only caller is dm_get_device(),
which does a dm_get_table_device() later on, which will properly
open the device.
So if the path string already _is_ in major:minor representation
we can convert it directly, avoiding a recursion into the filesystem
to lookup the block device.
This avoids a hang in multipath_message() when the filesystem is
inaccessible.
Fixes: 644bda6f34 ("dm table: fall back to getting device using name_to_dev_t()")
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3ed0dc35 upstream.
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78a18fec52 upstream.
Set the acpi_device pointer which acpi_bus_get_device() returns-by-
reference to NULL on errors.
We've recently had 2 cases where callers of acpi_bus_get_device()
did not properly error check the return value, so set the returned-
by-reference acpi_device pointer to NULL, because at least some
callers of acpi_bus_get_device() expect that to be done on errors.
[ rjw: This issue was exposed by commit 71da201f38 ("ACPI: scan:
Defer enumeration of devices with _DEP lists") which caused it to
be much more likely to occur on some systems, but the real defect
had been introduced by an earlier commit. ]
Fixes: 40e7fcb192 ("ACPI: Add _DEP support to fix battery issue on Asus T100TA")
Fixes: bcfcd409d4 ("usb: split code locating ACPI companion into port and device")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Diagnosed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: All applicable <stable@vger.kernel.org>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc1c2048ab upstream.
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b210de4f8c ]
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/1610027418-30438-1-git-send-email-ayal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eee7bd7e2 upstream.
This worked before, because we made all callers name their next pointer
"next". But in trying to be more "drop-in" ready, the silliness here is
revealed. This commit fixes the problem by making the macro argument and
the member use different names.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcfea72e79 upstream.
As part of the continual effort to remove direct usage of skb->next and
skb->prev, this patch adds a helper for iterating through the
singly-linked variant of skb lists, which are used for lists of GSO
packet. The name "skb_list_..." has been chosen to match the existing
function, "kfree_skb_list, which also operates on these singly-linked
lists, and the "..._walk_safe" part is the same idiom as elsewhere in
the kernel.
This patch removes the helper from wireguard and puts it into
linux/skbuff.h, while making it a bit more robust for general usage. In
particular, parenthesis are added around the macro argument usage, and it
now accounts for trying to iterate through an already-null skb pointer,
which will simply run the iteration zero times. This latter enhancement
means it can be used to replace both do { ... } while and while (...)
open-coded idioms.
This should take care of these three possible usages, which match all
current methods of iterations.
skb_list_walk_safe(segs, skb, next) { ... }
skb_list_walk_safe(skb, skb, next) { ... }
skb_list_walk_safe(segs, skb, segs) { ... }
Gcc appears to generate efficient code for each of these.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Just the skbuff.h changes for backporting - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d52e419ac8 ]
Clang static analysis reports the following:
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()")
Reported-by: Tom Rix <trix@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3226b158e6 ]
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: fd11a83dd3 ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df85bc140a ]
In commit 826f328e2b ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Fixes: 2f90b8657e ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Fixes: 826f328e2b ("net: dcb: Validate netlink message in DCB handler")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/a3edcfda0825f2aa2591801c5232f2bbf2d8a554.1610384801.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 826f328e2b ]
DCB uses the same handler function for both RTM_GETDCB and RTM_SETDCB
messages. dcb_doit() bounces RTM_SETDCB mesasges if the user does not have
the CAP_NET_ADMIN capability.
However, the operation to be performed is not decided from the DCB message
type, but from the DCB command. Thus DCB_CMD_*_GET commands are used for
reading DCB objects, the corresponding SET and DEL commands are used for
manipulation.
The assumption is that set-like commands will be sent via an RTM_SETDCB
message, and get-like ones via RTM_GETDCB. However, this assumption is not
enforced.
It is therefore possible to manipulate DCB objects without CAP_NET_ADMIN
capability by sending the corresponding command in an RTM_GETDCB message.
That is a bug. Fix it by validating the type of the request message against
the type used for the response.
Fixes: 2f90b8657e ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver")
Signed-off-by: Petr Machata <me@pmachata.org>
Link: https://lore.kernel.org/r/a2a9b88418f3a58ef211b718f2970128ef9e3793.1608673640.git.me@pmachata.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bd6b629c3 ]
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e56b3d94d9 ]
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1b ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2bc221b97 ]
For all PCI functions on the netxen_nic adapter, interrupt
mode (INTx or MSI) configuration is dependent on what has
been configured by the PCI function zero in the shared
interrupt register, as these adapters do not support mixed
mode interrupts among the functions of a given adapter.
Logic for setting MSI/MSI-x interrupt mode in the shared interrupt
register based on PCI function id zero check is not appropriate for
all family of netxen adapters, as for some of the netxen family
adapters PCI function zero is not really meant to be probed/loaded
in the host but rather just act as a management function on the device,
which caused all the other PCI functions on the adapter to always use
legacy interrupt (INTx) mode instead of choosing MSI/MSI-x interrupt mode.
This patch replaces that check with port number so that for all
type of adapters driver attempts for MSI/MSI-x interrupt modes.
Fixes: b37eb210c0 ("netxen_nic: Avoid mixed mode interrupts")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20210107101520.6735-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b2ee7d00 upstream.
If you export a subdirectory of a filesystem, a READDIRPLUS on the root
of that export will return the filehandle of the parent with the ".."
entry.
The filehandle is optional, so let's just not return the filehandle for
".." if we're at the root of an export.
Note that once the client learns one filehandle outside of the export,
they can trivially access the rest of the export using further lookups.
However, it is also not very difficult to guess filehandles outside of
the export. So exporting a subdirectory of a filesystem should
considered equivalent to providing access to the entire filesystem. To
avoid confusion, we recommend only exporting entire filesystems.
Reported-by: Youjipeng <wangzhibei1999@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6351c3f1c upstream.
The old way of changing the conntrack hashsize runtime was through changing
the module param via file /sys/module/nf_conntrack/parameters/hashsize. This
was extended to sysctl change in commit 3183ab8997 ("netfilter: conntrack:
allow increasing bucket size via sysctl too").
The commit introduced second "user" variable nf_conntrack_htable_size_user
which shadow actual variable nf_conntrack_htable_size. When hashsize is
changed via module param this "user" variable isn't updated. This results in
sysctl net/netfilter/nf_conntrack_buckets shows the wrong value when users
update via the old way.
This patch fix the issue by always updating "user" variable when reading the
proc file. This will take care of changes to the actual variable without
sysctl need to be aware.
Fixes: 3183ab8997 ("netfilter: conntrack: allow increasing bucket size via sysctl too")
Reported-by: Yoel Caspersen <yoel@kviknet.dk>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c22eeaff upstream.
As snd_ff.rx_bytes[] is unsigned int, and NSEC_PER_SEC is 1000000000L,
the second multiplication in
ff->rx_bytes[port] * 8 * NSEC_PER_SEC / 31250
always overflows on 32-bit platforms, truncating the result. Fix this
by precalculating "NSEC_PER_SEC / 31250", which is an integer constant.
Note that this assumes ff->rx_bytes[port] <= 16777.
Fixes: 1917429578 ("ALSA: fireface: add transaction support")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210111130251.361335-2-geert+renesas@glider.be
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f65df9c58 upstream.
As snd_fw_async_midi_port.consume_bytes is unsigned int, and
NSEC_PER_SEC is 1000000000L, the second multiplication in
port->consume_bytes * 8 * NSEC_PER_SEC / 31250
always overflows on 32-bit platforms, truncating the result. Fix this
by precalculating "NSEC_PER_SEC / 31250", which is an integer constant.
Note that this assumes port->consume_bytes <= 16777.
Fixes: 531f471834 ("ALSA: firewire-lib/firewire-tascam: localize async midi port")
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210111130251.361335-3-geert+renesas@glider.be
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0378c625af upstream.
There wasn't ever a real need to log an error in the kernel log for
ioctls issued with insufficient permissions. Simply return an error
and if an admin/user is sufficiently motivated they can enable DM's
dynamic debugging to see an explanation for why the ioctls were
disallowed.
Reported-by: Nir Soffer <nsoffer@redhat.com>
Fixes: e980f62353 ("dm: don't allow ioctls to targets that don't map to whole devices")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86b53fbf08 upstream.
A return value of 0 means success. This is documented in lib/kstrtox.c.
This was found by trying to mount an NFS share from a link-local IPv6
address with the interface specified by its index:
mount("[fe80::1%1]:/srv/nfs", "/mnt", "nfs", 0, "nolock,addr=fe80::1%1")
Before this commit this failed with EINVAL and also caused the following
message in dmesg:
[...] NFS: bad IP address specified: addr=fe80::1%1
The syscall using the same address based on the interface name instead
of its index succeeds.
Credits for this patch go to my colleague Christian Speich, who traced
the origin of this bug to this line of code.
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Fixes: 00cfaa943e ("replace strict_strto calls")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ff60eb052 upstream.
acquire_slab() fails if there is contention on the freelist of the page
(probably because some other CPU is concurrently freeing an object from
the page). In that case, it might make sense to look for a different page
(since there might be more remote frees to the page from other CPUs, and
we don't want contention on struct page).
However, the current code accidentally stops looking at the partial list
completely in that case. Especially on kernels without CONFIG_NUMA set,
this means that get_partial() fails and new_slab_objects() falls back to
new_slab(), allocating new pages. This could lead to an unnecessary
increase in memory fragmentation.
Link: https://lkml.kernel.org/r/20201228130853.1871516-1-jannh@google.com
Fixes: 7ced371971 ("slub: Acquire_slab() avoid loop")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 896567ee7f upstream.
Before referencing the inode, we must ensure that the superblock can be
referenced. Otherwise, we can end up with iput() calling superblock
operations that are no longer valid or accessible.
Fixes: ea7c38fef0 ("NFSv4: Ensure we reference the inode for return-on-close in delegreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67bbceedc9 upstream.
If the layout return-on-close failed because the layoutreturn was never
sent, then we should mark the layout for return again.
Fixes: 9c47b18cf7 ("pNFS: Ensure we do clear the return-on-close layout stateid on fatal errors")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1a90ab0e upstream.
It is only safe to call the tracepoint before rpc_put_task() because
'data' is freed inside nfs4_lock_release (rpc_release).
Fixes: 48c9579a1a ("Adding stateid information to tracepoints")
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d36a1dd9f7 upstream.
We are not guaranteed the locking environment that would prevent
dentry getting renamed right under us. And it's possible for
old long name to be freed after rename, leading to UAF here.
Cc: stable@kernel.org # v2.6.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee61cfd955 ]
It adds a stub acpi_create_platform_device() for !CONFIG_ACPI build, so
that caller doesn't have to deal with !CONFIG_ACPI build issue.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445c6198fe ]
Since commit 1d6cd39293 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51049bd903 ]
Without this, we run into a link error
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 887078de2a ]
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cfccb3c04 ]
The top-level boot_targets (uImage and uImage.*) should be phony
targets. They just let Kbuild descend into arch/arc/boot/ and create
files there.
If a file exists in the top directory with the same name, the boot
image will not be created.
You can confirm it by the following steps:
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig all # vmlinux will be built
$ touch uImage.gz
$ make ARCH=arc uImage.gz
CALL scripts/atomic/check-atomics.sh
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
# arch/arc/boot/uImage.gz is not created
Specify the targets as PHONY to fix this.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2712ec76a ]
arch/arc/boot/Makefile supports uImage.lzma, but you cannot do
'make uImage.lzma' because the corresponding target is missing
in arch/arc/Makefile. Add it.
I also changed the assignment operator '+=' to ':=' since this is the
only place where we expect this variable to be set.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9836720911 ]
The deb-pkg builds for ARCH=arc fail.
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig
$ make ARCH=arc bindeb-pkg
SORTTAB vmlinux
SYSMAP System.map
MODPOST Module.symvers
make KERNELRELEASE=5.10.0-rc4 ARCH=arc KBUILD_BUILD_VERSION=2 -f ./Makefile intdeb-pkg
sh ./scripts/package/builddeb
cp: cannot stat 'arch/arc/boot/bootpImage': No such file or directory
make[4]: *** [scripts/Makefile.package:87: intdeb-pkg] Error 1
make[3]: *** [Makefile:1527: intdeb-pkg] Error 2
make[2]: *** [debian/rules:13: binary-arch] Error 2
dpkg-buildpackage: error: debian/rules binary subprocess returned exit status 2
make[1]: *** [scripts/Makefile.package:83: bindeb-pkg] Error 2
make: *** [Makefile:1527: bindeb-pkg] Error 2
The reason is obvious; arch/arc/Makefile sets $(boot)/bootpImage as
the default image, but there is no rule to build it.
Remove the meaningless KBUILD_IMAGE assignment so it will fallback
to the default vmlinux. With this change, you can build the deb package.
I removed the 'bootpImage' target as well. At best, it provides
'make bootpImage' as an alias of 'make vmlinux', but I do not see
much sense in doing so.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b4b8e6b4a ]
We got a "deleted inode referenced" warning cross our fsstress test. The
bug can be reproduced easily with following steps:
cd /dev/shm
mkdir test/
fallocate -l 128M img
mkfs.ext4 -b 1024 img
mount img test/
dd if=/dev/zero of=test/foo bs=1M count=128
mkdir test/dir/ && cd test/dir/
for ((i=0;i<1000;i++)); do touch file$i; done # consume all block
cd ~ && renameat2(AT_FDCWD, /dev/shm/test/dir/file1, AT_FDCWD,
/dev/shm/test/dir/dst_file, RENAME_WHITEOUT) # ext4_add_entry in
ext4_rename will return ENOSPC!!
cd /dev/shm/ && umount test/ && mount img test/ && ls -li test/dir/file1
We will get the output:
"ls: cannot access 'test/dir/file1': Structure needs cleaning"
and the dmesg show:
"EXT4-fs error (device loop0): ext4_lookup:1626: inode #2049: comm ls:
deleted inode referenced: 139"
ext4_rename will create a special inode for whiteout and use this 'ino'
to replace the source file's dir entry 'ino'. Once error happens
latter(the error above was the ENOSPC return from ext4_add_entry in
ext4_rename since all space has been consumed), the cleanup do drop the
nlink for whiteout, but forget to restore 'ino' with source file. This
will trigger the bug describle as above.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Fixes: cd808deced ("ext4: support RENAME_WHITEOUT")
Link: https://lore.kernel.org/r/20210105062857.3566-1-yangerkun@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cb82a54904 upstream.
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcc4233837 upstream.
If the origin device has a volatile write-back cache and the following
events occur:
1: After finishing merge operation of one set of exceptions,
merge_callback() is invoked.
2: Update the metadata in COW device tracking the merge completion.
This update to COW device is flushed cleanly.
3: System crashes and the origin device's cache where the recent
merge was completed has not been flushed.
During the next cycle when we read the metadata from the COW device,
we will skip reading those metadata whose merge was completed in
step (1). This will lead to data loss/corruption.
To address this, flush the origin device post merge IO before
updating the metadata.
Cc: stable@vger.kernel.org
Signed-off-by: Akilesh Kailash <akailash@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a58015d638 upstream.
Linux VM on Hyper-V crashes with the latest mainline:
[ 4.069624] detected buffer overflow in strcpy
[ 4.077733] kernel BUG at lib/string.c:1149!
..
[ 4.085819] RIP: 0010:fortify_panic+0xf/0x11
...
[ 4.085819] Call Trace:
[ 4.085819] acpi_device_add.cold.15+0xf2/0xfb
[ 4.085819] acpi_add_single_object+0x2a6/0x690
[ 4.085819] acpi_bus_check_add+0xc6/0x280
[ 4.085819] acpi_ns_walk_namespace+0xda/0x1aa
[ 4.085819] acpi_walk_namespace+0x9a/0xc2
[ 4.085819] acpi_bus_scan+0x78/0x90
[ 4.085819] acpi_scan_init+0xfa/0x248
[ 4.085819] acpi_init+0x2c1/0x321
[ 4.085819] do_one_initcall+0x44/0x1d0
[ 4.085819] kernel_init_freeable+0x1ab/0x1f4
This is because of the recent buffer overflow detection in the
commit 6a39e62abb ("lib: string.h: detect intra-object overflow in
fortified string functions")
Here acpi_device_bus_id->bus_id can only hold 14 characters, while the
the acpi_device_hid(device) returns a 22-char string
"HYPER_V_GEN_COUNTER_V1".
Per ACPI Spec v6.2, Section 6.1.5 _HID (Hardware ID), if the ID is a
string, it must be of the form AAA#### or NNNN####, i.e. 7 chars or 8
chars.
The field bus_id in struct acpi_device_bus_id was originally defined as
char bus_id[9], and later was enlarged to char bus_id[15] in 2007 in the
commit bb0958544f ("ACPI: use more understandable bus_id for ACPI
devices")
Fix the issue by changing the field bus_id to const char *, and use
kstrdup_const() to initialize it.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Tested-By: Jethro Beekman <jethro@fortanix.com>
[ rjw: Subject change, whitespace adjustment ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69e976831c upstream.
LLVM-built Linux triggered a boot hangup with KASLR enabled.
arch/mips/kernel/relocate.c:get_random_boot() uses linux_banner,
which is a string constant, as a random seed, but accesses it
as an array of unsigned long (in rotate_xor()).
When the address of linux_banner is not aligned to sizeof(long),
such access emits unaligned access exception and hangs the kernel.
Use PTR_ALIGN() to align input address to sizeof(long) and also
align down the input length to prevent possible access-beyond-end.
Fixes: 405bc8fd12 ("MIPS: Kernel: Implement KASLR using CONFIG_RELOCATABLE")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d4f9c1a17 upstream.
The compressed payload is not necesarily 4-byte aligned, at least when
compiling with Clang. In that case, the 4-byte value appended to the
compressed payload that corresponds to the uncompressed kernel image
size must be read using get_unaligned_le32().
This fixes Clang-built kernels not booting on MIPS (tested on a Ingenic
JZ4770 board).
Fixes: b8f54f2cde ("MIPS: ZBOOT: copy appended dtb to the end of the kernel")
Cc: <stable@vger.kernel.org> # v4.7
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c6679b5cb upstream.
A widget's "dirty" list_head, much like its "list" list_head, eventually
chains back to a list_head on the snd_soc_card itself. This means that
the list can stick around even after the widget (or all widgets) have
been freed. Currently, however, widgets that are in the dirty list when
freed remain there, corrupting the entire list and leading to memory
errors and undefined behavior when the list is next accessed or
modified.
I encountered this issue when a component failed to probe relatively
late in snd_soc_bind_card(), causing it to bail out and call
soc_cleanup_card_resources(), which eventually called
snd_soc_dapm_free() with widgets that were still dirty from when they'd
been added.
Fixes: db432b414e ("ASoC: Do DAPM power checks only for widgets changed since last run")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/f8b5f031d50122bf1a9bfc9cae046badf4a7a31a.1607822410.git.tommyhebb@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a5f1b67ec upstream.
We reset the guest's view of PMCR_EL0 unconditionally, based on
the host's view of this register. It is however legal for an
implementation not to provide any PMU, resulting in an UNDEF.
The obvious fix is to skip the reset of this shadow register
when no PMU is available, sidestepping the issue entirely.
If no PMU is available, the guest is not able to request
a virtual PMU anyway, so not doing nothing is the right thing
to do!
It is unlikely that this bug can hit any HW implementation
though, as they all provide a PMU. It has been found using nested
virt with the host KVM not implementing the PMU itself.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201210083059.1277162-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69931e1128 upstream.
Without this, the driver runs into a link failure
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_ds26522_probe':
slic_ds26522.c:(.text+0x100c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: slic_ds26522.c:(.text+0x1cdc): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_write':
slic_ds26522.c:(.text+0x1e4c): undefined reference to `byte_rev_table'
Fixes: c37d4a0085 ("Maxim/driver: Add driver for maxim ds26522")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6eb072a9 upstream.
mlx5e_create_ttc_table_groups() frees ft->g on failure of
kvzalloc(), but such failure will be caught by its caller
in mlx5e_create_ttc_table() and ft->g will be freed again
in mlx5e_destroy_flow_table(). The same issue also occurs
in mlx5e_create_ttc_table_groups(). Set ft->g to NULL after
kfree() to avoid double free.
Fixes: 7b3722fa9e ("net/mlx5e: Support RSS for GRE tunneled packets")
Fixes: 33cfaaa8f3 ("net/mlx5e: Split the main flow steering table")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0bb12c58 upstream.
When mlx5_create_flow_group() fails, ft->g should be
freed just like when kvzalloc() fails. The caller of
mlx5e_create_l2_table_groups() does not catch this
issue on failure, which leads to memleak.
Fixes: 33cfaaa8f3 ("net/mlx5e: Split the main flow steering table")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e186620d7b upstream.
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a970650 ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a590370d91 upstream.
if cur_bpw <= 8 and xfer_len < 4 then the value of fthlv will be 1 and
SPI registers content may have been lost.
* If SPI data register is accessed as a 16-bit register and DSIZE <= 8bit,
better to select FTHLV = 2, 4, 6 etc
* If SPI data register is accessed as a 32-bit register and DSIZE > 8bit,
better to select FTHLV = 2, 4, 6 etc, while if DSIZE <= 8bit,
better to select FTHLV = 4, 8, 12 etc
Signed-off-by: Roman Guskov <rguskov@dh-electronics.com>
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201221123532.27272-1-rguskov@dh-electronics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 943bdd0cec upstream.
Currently there is an unlikely case where cpufreq_cpu_get() returns a
NULL policy and this will cause a NULL pointer dereference later on.
Fix this by passing the policy to transition_frequency_fidvid() from
the caller and hence eliminating the need for the cpufreq_cpu_get()
and cpufreq_cpu_put().
Thanks to Viresh Kumar for suggesting the fix.
Addresses-Coverity: ("Dereference null return")
Fixes: b43a7ffbf3 ("cpufreq: Notify all policy->cpus in cpufreq_notify_transition()")
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b884fe71f upstream.
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec76c2eea9 upstream.
On the GTA04A5 od->_driver_status was not set to BUS_NOTIFY_BIND_DRIVER
during probe of the second mmc used for wifi. Therefore
omap_device_late_idle idled the device during probing causing oopses when
accessing the registers.
It was not set because od->_state was set to OMAP_DEVICE_STATE_IDLE
in the notifier callback. Therefore set od->_driver_status also in that
case.
This came apparent after commit 21b2cec61c ("mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") causing this
oops:
omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling
8<--- cut here ---
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0b402c
...
(omap_hsmmc_set_bus_width) from [<c07996bc>] (omap_hsmmc_set_ios+0x11c/0x258)
(omap_hsmmc_set_ios) from [<c077b2b0>] (mmc_power_up.part.8+0x3c/0xd0)
(mmc_power_up.part.8) from [<c077c14c>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c077d284>] (mmc_add_host+0x58/0x84)
(mmc_add_host) from [<c0799190>] (omap_hsmmc_probe+0x5fc/0x8c0)
(omap_hsmmc_probe) from [<c0666728>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c066457c>] (really_probe+0x1dc/0x3b4)
Fixes: 04abaf07f6 ("ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer")
Fixes: 21b2cec61c ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: left out extra parens, trimmed description stack trace]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f9bce7a22 upstream
If we are using edge IRQs, new samples can arrive while processing
current interrupt since there are no hw guarantees the irq line
stays "low" long enough to properly detect the new interrupt.
In this case the new sample will be missed.
Polling FIFO status register in st_lsm6dsx_handler_thread routine
allow us to read new samples even if the interrupt arrives while
processing previous data and the timeslot where the line is "low"
is too short to be properly detected.
Fixes: 89ca88a7cd ("iio: imu: st_lsm6dsx: support active-low interrupts")
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/5e93cda7dc1e665f5685c53ad8e9ea71dbae782d.1605378871.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[sudip: manual backport to old irq handler path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20f1431160 upstream
Write buffers use a kmalloc()'ed buffer, they can leak
up to seven bytes of kernel memory to flash if writes are not
aligned.
So use ubifs_pad() to fill these gaps with padding bytes.
This was never a problem while scanning because the scanner logic
manually aligns node lengths and skips over these gaps.
Cc: <stable@vger.kernel.org>
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e53656ad8 upstream
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch
Fixes: 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: CQ Tang <cq.tang@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
(cherry picked from commit 5f22cc0b13)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[sudip: use file from old path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eff8728fe6 upstream.
Basically, consider .text.{hot|unlikely|unknown}.* part of .text, too.
When compiling with profiling information (collected via PGO
instrumentations or AutoFDO sampling), Clang will separate code into
.text.hot, .text.unlikely, or .text.unknown sections based on profiling
information. After D79600 (clang-11), these sections will have a
trailing `.` suffix, ie. .text.hot., .text.unlikely., .text.unknown..
When using -ffunction-sections together with profiling infomation,
either explicitly (FGKASLR) or implicitly (LTO), code may be placed in
sections following the convention:
.text.hot.<foo>, .text.unlikely.<bar>, .text.unknown.<baz>
where <foo>, <bar>, and <baz> are functions. (This produces one section
per function; we generally try to merge these all back via linker script
so that we don't have 50k sections).
For the above cases, we need to teach our linker scripts that such
sections might exist and that we'd explicitly like them grouped
together, otherwise we can wind up with code outside of the
_stext/_etext boundaries that might not be mapped properly for some
architectures, resulting in boot failures.
If the linker script is not told about possible input sections, then
where the section is placed as output is a heuristic-laiden mess that's
non-portable between linkers (ie. BFD and LLD), and has resulted in many
hard to debug bugs. Kees Cook is working on cleaning this up by adding
--orphan-handling=warn linker flag used in ARCH=powerpc to additional
architectures. In the case of linker scripts, borrowing from the Zen of
Python: explicit is better than implicit.
Also, ld.bfd's internal linker script considers .text.hot AND
.text.hot.* to be part of .text, as well as .text.unlikely and
.text.unlikely.*. I didn't see support for .text.unknown.*, and didn't
see Clang producing such code in our kernel builds, but I see code in
LLVM that can produce such section names if profiling information is
missing. That may point to a larger issue with generating or collecting
profiles, but I would much rather be safe and explicit than have to
debug yet another issue related to orphan section placement.
Reported-by: Jian Cai <jiancai@google.com>
Suggested-by: Fāng-ruì Sòng <maskray@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Luis Lozano <llozano@google.com>
Tested-by: Manoj Gupta <manojgupta@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commitdiff;h=add44f8d5c5c05e08b11e033127a744d61c26aee
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commitdiff;h=1de778ed23ce7492c523d5850c6c6dbb34152655
Link: https://reviews.llvm.org/D79600
Link: https://bugs.chromium.org/p/chromium/issues/detail?id=1084760
Link: https://lore.kernel.org/r/20200821194310.3089815-7-keescook@chromium.org
Debugged-by: Luis Lozano <llozano@google.com>
[nc: Resolve small conflict due to lack of NOINSTR_TEXT]
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae28d1aae4 upstream
Currently, when moving a task to a resource group the PQR_ASSOC MSR is
updated with the new closid and rmid in an added task callback. If the
task is running, the work is run as soon as possible. If the task is not
running, the work is executed later in the kernel exit path when the
kernel returns to the task again.
Updating the PQR_ASSOC MSR as soon as possible on the CPU a moved task
is running is the right thing to do. Queueing work for a task that is
not running is unnecessary (the PQR_ASSOC MSR is already updated when
the task is scheduled in) and causing system resource waste with the way
in which it is implemented: Work to update the PQR_ASSOC register is
queued every time the user writes a task id to the "tasks" file, even if
the task already belongs to the resource group.
This could result in multiple pending work items associated with a
single task even if they are all identical and even though only a single
update with most recent values is needed. Specifically, even if a task
is moved between different resource groups while it is sleeping then it
is only the last move that is relevant but yet a work item is queued
during each move.
This unnecessary queueing of work items could result in significant
system resource waste, especially on tasks sleeping for a long time.
For example, as demonstrated by Shakeel Butt in [1] writing the same
task id to the "tasks" file can quickly consume significant memory. The
same problem (wasted system resources) occurs when moving a task between
different resource groups.
As pointed out by Valentin Schneider in [2] there is an additional issue
with the way in which the queueing of work is done in that the task_struct
update is currently done after the work is queued, resulting in a race with
the register update possibly done before the data needed by the update is
available.
To solve these issues, update the PQR_ASSOC MSR in a synchronous way
right after the new closid and rmid are ready during the task movement,
only if the task is running. If a moved task is not running nothing
is done since the PQR_ASSOC MSR will be updated next time the task is
scheduled. This is the same way used to update the register when tasks
are moved as part of resource group removal.
[1] https://lore.kernel.org/lkml/CALvZod7E9zzHwenzf7objzGKsdBmVwTgEJ0nPgs0LUFU3SN5Pw@mail.gmail.com/
[2] https://lore.kernel.org/lkml/20201123022433.17905-1-valentin.schneider@arm.com
[ bp: Massage commit message and drop the two update_task_closid_rmid()
variants. ]
Backporting notes:
Since upstream commit fa7d949337 ("x86/resctrl: Rename and move rdt
files to a separate directory"), the file
arch/x86/kernel/cpu/intel_rdt_rdtgroup.c has been renamed and moved to
arch/x86/kernel/cpu/resctrl/rdtgroup.c.
Apply the change against file arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
for older stable trees.
Since upstream commit 352940ecec ("x86/resctrl: Rename the RDT
functions and definitions"), resctrl functions received more generic
names. Specifically related to this backport, intel_rdt_sched_in()
was renamed to rescrl_sched_in().
Fixes: e02737d5b8 ("x86/intel_rdt: Add tasks files")
Reported-by: Shakeel Butt <shakeelb@google.com>
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/17aa2fb38fc12ce7bb710106b3e7c7b45acb9e94.1608243147.git.reinette.chatre@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 50c661670f ]
For some reason ip_tunnel insist on setting the DF bit anyway when the
inner header has the DF bit set, EVEN if the tunnel was configured with
'nopmtudisc'.
This means that the script added in the previous commit
cannot be made to work by adding the 'nopmtudisc' flag to the
ip tunnel configuration. Doing so breaks connectivity even for the
without-conntrack/netfilter scenario.
When nopmtudisc is set, the tunnel will skip the mtu check, so no
icmp error is sent to client. Then, because inner header has DF set,
the outer header gets added with DF bit set as well.
IP stack then sends an error to itself because the packet exceeds
the device MTU.
Fixes: 23a3647bc4 ("ip_tunnels: Use skb-len to PMTU check.")
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bb4cc1a188 ]
Conntrack reassembly records the largest fragment size seen in IPCB.
However, when this gets forwarded/transmitted, fragmentation will only
be forced if one of the fragmented packets had the DF bit set.
In that case, a flag in IPCB will force fragmentation even if the
MTU is large enough.
This should work fine, but this breaks with ip tunnels.
Consider client that sends a UDP datagram of size X to another host.
The client fragments the datagram, so two packets, of size y and z, are
sent. DF bit is not set on any of these packets.
Middlebox netfilter reassembles those packets back to single size-X
packet, before routing decision.
packet-size-vs-mtu checks in ip_forward are irrelevant, because DF bit
isn't set. At output time, ip refragmentation is skipped as well
because x is still smaller than the mtu of the output device.
If ttransmit device is an ip tunnel, the packet size increases to
x+overhead.
Also, tunnel might be configured to force DF bit on outer header.
In this case, packet will be dropped (exceeds MTU) and an ICMP error is
generated back to sender.
But sender already respects the announced MTU, all the packets that
it sent did fit the announced mtu.
Force refragmentation as per original sizes unconditionally so ip tunnel
will encapsulate the fragments instead.
The only other solution I see is to place ip refragmentation in
the ip_tunnel code to handle this case.
Fixes: d6b915e29f ("ip_fragment: don't forward defragmented DF packet")
Reported-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55b7ab1178 ]
VLAN checks for NETREG_UNINITIALIZED to distinguish between
registration failure and unregistration in progress.
Since commit cb626bf566 ("net-sysfs: Fix reference count leak")
registration failure may, however, result in NETREG_UNREGISTERED
as well as NETREG_UNINITIALIZED.
This fix is similer to cebb69754f ("rtnetlink: Fix
memory(net_device) leak when ->newlink fails")
Fixes: cb626bf566 ("net-sysfs: Fix reference count leak")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a68d725e4 ]
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d85be8a49e ]
The placeholder for instruction selection should use the second
argument's operand, which is %1, not %0. This could generate incorrect
assembly code if the memory addressing of operand %0 is a different
form from that of operand %1.
Also remove the %Un placeholder because having %Un placeholders
for two operands which are based on the same local var (ptep) doesn't
make much sense. By the way, it doesn't change the current behaviour
because "<>" constraint is missing for the associated "=m".
[chleroy: revised commit log iaw segher's comments and removed %U0]
Fixes: 9bf2b5cdc5 ("powerpc: Fixes for CONFIG_PTE_64BIT for SMP support")
Cc: <stable@vger.kernel.org> # v2.6.28+
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/96354bd77977a6a933fe9020da57629007fdb920.1603358942.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2896c93811 upstream.
When attempting to match EXTENDED COPY CSCD descriptors with corresponding
se_devices, target_xcopy_locate_se_dev_e4() currently iterates over LIO's
global devices list which includes all configured backstores.
This change ensures that only initiator-accessible backstores are
considered during CSCD descriptor lookup, according to the session's
se_node_acl LUN list.
To avoid LUN removal race conditions, device pinning is changed from being
configfs based to instead using the se_node_acl lun_ref.
Reference: CVE-2020-28374
Fixes: cbf031f425 ("target: Add support for EXTENDED_COPY copy offload emulation")
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb7f4a8b1f upstream.
In mtrr_type_lookup(), if the input memory address region is not in the
MTRR, over 4GB, and not over the top of memory, a write-back attribute
is returned. These condition checks are for ensuring the input memory
address region is actually mapped to the physical memory.
However, if the end address is just aligned with the top of memory,
the condition check treats the address is over the top of memory, and
write-back attribute is not returned.
And this hits in a real use case with NVDIMM: the nd_pmem module tries
to map NVDIMMs as cacheable memories when NVDIMMs are connected. If a
NVDIMM is the last of the DIMMs, the performance of this NVDIMM becomes
very low since it is aligned with the top of memory and its memory type
is uncached-minus.
Move the input end address change to inclusive up into
mtrr_type_lookup(), before checking for the top of memory in either
mtrr_type_lookup_{variable,fixed}() helpers.
[ bp: Massage commit message. ]
Fixes: 0cc705f56e ("x86/mm/mtrr: Clean up mtrr_type_lookup()")
Signed-off-by: Ying-Tsun Huang <ying-tsun.huang@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201215070721.4349-1-ying-tsun.huang@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c8193f568 upstream.
htable_bits() can call jhash_size(32) and trigger shift-out-of-bounds
UBSAN: shift-out-of-bounds in net/netfilter/ipset/ip_set_hash_gen.h:151:6
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 8498 Comm: syz-executor519
Not tainted 5.10.0-rc7-next-20201208-syzkaller #0
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:395
htable_bits net/netfilter/ipset/ip_set_hash_gen.h:151 [inline]
hash_mac_create.cold+0x58/0x9b net/netfilter/ipset/ip_set_hash_gen.h:1524
ip_set_create+0x610/0x1380 net/netfilter/ipset/ip_set_core.c:1115
nfnetlink_rcv_msg+0xecc/0x1180 net/netfilter/nfnetlink.c:252
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
nfnetlink_rcv+0x1ac/0x420 net/netfilter/nfnetlink.c:600
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x907/0xe40 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6e8/0x810 net/socket.c:2345
___sys_sendmsg+0xf3/0x170 net/socket.c:2399
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2432
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch replaces htable_bits() by simple fls(hashsize - 1) call:
it alone returns valid nbits both for round and non-round hashsizes.
It is normal to set any nbits here because it is validated inside
following htable_size() call which returns 0 for nbits>31.
Fixes: 1feab10d7e6d("netfilter: ipset: Unified hash type generation")
Reported-by: syzbot+d66bfadebca46cf61a2b@syzkaller.appspotmail.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47f4469970 upstream.
While commit d5dcce0c41 ("device property: Keep secondary firmware
node secondary by type") describes everything correct in its commit
message, the change it made does the opposite and original commit
c15e1bdda4 ("device property: Fix the secondary firmware node handling
in set_primary_fwnode()") was fully correct.
Revert the former one here and improve documentation in the next patch.
Fixes: d5dcce0c41 ("device property: Keep secondary firmware node secondary by type")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1c5246e08 upstream.
Commit
28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
introduced a new location where a pmd was released, but neglected to
run the pmd page destructor. In fact, this happened previously for a
different pmd release path and was fixed by commit:
c283610e44 ("x86, mm: do not leak page->ptl for pmd page tables").
This issue was hidden until recently because the failure mode is silent,
but commit:
b2b29d6d01 ("mm: account PMD tables like PTE tables")
turns the failure mode into this signature:
BUG: Bad page state in process lt-pmem-ns pfn:15943d
page:000000007262ed7b refcount:0 mapcount:-1024 mapping:0000000000000000 index:0x0 pfn:0x15943d
flags: 0xaffff800000000()
raw: 00affff800000000 dead000000000100 0000000000000000 0000000000000000
raw: 0000000000000000 ffff913a029bcc08 00000000fffffbff 0000000000000000
page dumped because: nonzero mapcount
[..]
dump_stack+0x8b/0xb0
bad_page.cold+0x63/0x94
free_pcp_prepare+0x224/0x270
free_unref_page+0x18/0xd0
pud_free_pmd_page+0x146/0x160
ioremap_pud_range+0xe3/0x350
ioremap_page_range+0x108/0x160
__ioremap_caller.constprop.0+0x174/0x2b0
? memremap+0x7a/0x110
memremap+0x7a/0x110
devm_memremap+0x53/0xa0
pmem_attach_disk+0x4ed/0x530 [nd_pmem]
? __devm_release_region+0x52/0x80
nvdimm_bus_probe+0x85/0x210 [libnvdimm]
Given this is a repeat occurrence it seemed prudent to look for other
places where this destructor might be missing and whether a better
helper is needed. try_to_free_pmd_page() looks like a candidate, but
testing with setting up and tearing down pmd mappings via the dax unit
tests is thus far not triggering the failure.
As for a better helper pmd_free() is close, but it is a messy fit
due to requiring an @mm arg. Also, ___pmd_free_tlb() wants to call
paravirt_tlb_remove_table() instead of free_page(), so open-coded
pgtable_pmd_page_dtor() seems the best way forward for now.
Debugged together with Matthew Wilcox <willy@infradead.org>.
Fixes: 28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/160697689204.605323.17629854984697045602.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove an unused variable which was mistakingly left by commit
37faf50615 ("USB: serial: keyspan_pda: fix write-wakeup
use-after-free") and only removed by a later change.
This is needed to suppress a W=1 warning about the unused variable in
the stable trees that the build bots triggers.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64e6bbfff5 upstream.
There is a use-after-free issue, if access udc_name
in function gadget_dev_desc_UDC_store after another context
free udc_name in function unregister_gadget.
Context 1:
gadget_dev_desc_UDC_store()->unregister_gadget()->
free udc_name->set udc_name to NULL
Context 2:
gadget_dev_desc_UDC_show()-> access udc_name
Call trace:
dump_backtrace+0x0/0x340
show_stack+0x14/0x1c
dump_stack+0xe4/0x134
print_address_description+0x78/0x478
__kasan_report+0x270/0x2ec
kasan_report+0x10/0x18
__asan_report_load1_noabort+0x18/0x20
string+0xf4/0x138
vsnprintf+0x428/0x14d0
sprintf+0xe4/0x12c
gadget_dev_desc_UDC_show+0x54/0x64
configfs_read_file+0x210/0x3a0
__vfs_read+0xf0/0x49c
vfs_read+0x130/0x2b4
SyS_read+0x114/0x208
el0_svc_naked+0x34/0x38
Add mutex_lock to protect this kind of scenario.
Signed-off-by: Eddie Hung <eddie.hung@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1609239215-21819-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cd0fe9138 upstream.
When binding the ConfigFS gadget to a UDC, the functions in each
configuration are added in list order. However, if usb_add_function()
fails, the failed function is put back on its configuration's
func_list and purge_configs_funcs() is called to further clean up.
purge_configs_funcs() iterates over the configurations and functions
in forward order, calling unbind() on each of the previously added
functions. But after doing so, each function gets moved to the
tail of the configuration's func_list. This results in reshuffling
the original order of the functions within a configuration such
that the failed function now appears first even though it may have
originally appeared in the middle or even end of the list. At this
point if the ConfigFS gadget is attempted to re-bind to the UDC,
the functions will be added in a different order than intended,
with the only recourse being to remove and relink the functions all
over again.
An example of this as follows:
ln -s functions/mass_storage.0 configs/c.1
ln -s functions/ncm.0 configs/c.1
ln -s functions/ffs.adb configs/c.1 # oops, forgot to start adbd
echo "<udc device>" > UDC # fails
start adbd
echo "<udc device>" > UDC # now succeeds, but...
# bind order is
# "ADB", mass_storage, ncm
[30133.118289] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30133.119875] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30133.119974] using random self ethernet address
[30133.120002] using random host ethernet address
[30133.139604] usb0: HOST MAC 3e:27:46:ba:3e:26
[30133.140015] usb0: MAC 6e:28:7e:42:66:6a
[30133.140062] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30133.140081] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 --> -19
[30133.140098] configfs-gadget gadget: unbind function 'Mass Storage Function'/ffffff810af87200
[30133.140119] configfs-gadget gadget: unbind function 'cdc_network'/ffffff80f48d1a00
[30133.173201] configfs-gadget a600000.dwc3: failed to start g1: -19
[30136.661933] init: starting service 'adbd'...
[30136.700126] read descriptors
[30136.700413] read strings
[30138.574484] configfs-gadget gadget: adding 'Function FS Gadget'/ffffff80f3868438 to config 'c'/ffffff817d6a2520
[30138.575497] configfs-gadget gadget: adding 'Mass Storage Function'/ffffff810af87200 to config 'c'/ffffff817d6a2520
[30138.575554] configfs-gadget gadget: adding 'cdc_network'/ffffff80f48d1a00 to config 'c'/ffffff817d6a2520
[30138.575631] using random self ethernet address
[30138.575660] using random host ethernet address
[30138.595338] usb0: HOST MAC 2e:cf:43💿ca:c8
[30138.597160] usb0: MAC 6a:f0:9f:ee:82:a0
[30138.791490] configfs-gadget gadget: super-speed config #1: c
Fix this by reversing the iteration order of the functions in
purge_config_funcs() when unbinding them, and adding them back to
the config's func_list at the head instead of the tail. This
ensures that we unbind and unwind back to the original list order.
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201229224443.31623-1-jackp@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc35c224a upstream.
There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.
This would result in the below call stack and leads to stall.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
(detected by 2, t=5252 jiffies, g=20129, q=3770)
Task dump for CPU 3:
task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid:
636 flags:0x00000202
Call trace:
__switch_to+0xc0/0x170
_raw_spin_lock_irqsave+0x84/0xb0
composite_disconnect+0x28/0x78
configfs_composite_disconnect+0x68/0x70
usb_gadget_disconnect+0x10c/0x128
usb_gadget_deactivate+0xd4/0x108
usb_function_deactivate+0x6c/0x80
uvc_function_disconnect+0x20/0x58
uvc_v4l2_release+0x30/0x88
v4l2_release+0xbc/0xf0
__fput+0x7c/0x230
____fput+0x14/0x20
task_work_run+0x88/0x140
do_notify_resume+0x240/0x6f0
work_pending+0x8/0x200
Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.
The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9389044f27 upstream.
With commit 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.
Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.
Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 020a1f4534 upstream.
Stack-allocated buffers cannot be used for DMA (on all architectures).
Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.
Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 372c931319 upstream.
Make sure to always cancel the control URB in write() so that it can be
reused after a timeout or spurious CMD_ACK.
Currently any further write requests after a timeout would fail after
triggering a WARN() in usb_submit_urb() when attempting to submit the
already active URB.
Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5323a6f3 upstream.
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce722da66d upstream.
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.
[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
Databook, 2.70a, December 2013, p.388
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2459108b5 upstream.
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0aa171e9b2 upstream.
Pavel reports that commit 17858b140b ("crypto: ecdh - avoid unaligned
accesses in ecdh_set_secret()") fixes one problem but introduces another:
the unconditional memcpy() introduced by that commit may overflow the
target buffer if the source data is invalid, which could be the result of
intentional tampering.
So check params.key_size explicitly against the size of the target buffer
before validating the key further.
Fixes: 17858b140b ("crypto: ecdh - avoid unaligned accesses in ecdh_set_secret()")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
db49200b1d is backported from the mainline commit
5f1251a48c ("video: hyperv_fb: Fix the cache type when mapping the VRAM"),
to v5.4.y and older stable branches, but unluckily db49200b1d causes
mmap() to fail for /dev/fb0 due to EINVAL:
[ 5797.049560] x86/PAT: a.out:1910 map pfn expected mapping type
uncached-minus for [mem 0xf8200000-0xf85cbfff], got write-back
This means the v5.4.y kernel detects an incompatibility issue about the
mapping type of the VRAM: db49200b1d changes to use Write-Back when
mapping the VRAM, while the mmap() syscall tries to use Uncached-minus.
That’s to say, the kernel thinks Uncached-minus is incompatible with
Write-Back: see drivers/video/fbdev/core/fbmem.c: fb_mmap() ->
vm_iomap_memory() -> io_remap_pfn_range() -> ... -> track_pfn_remap() ->
reserve_pfn_range().
Note: any v5.5 and newer kernel doesn't have the issue, because they
have commit
d21987d709 ("video: hyperv: hyperv_fb: Support deferred IO for Hyper-V frame buffer driver")
, and when the hyperv_fb driver has the deferred_io support,
fb_deferred_io_init() overrides info->fbops->fb_mmap with
fb_deferred_io_mmap(), which doesn’t check the mapping type
incompatibility. Note: since it's VRAM here, the checking is not really
necessary.
Fix the regression by ioremap_wc(), which uses Write-combining. The kernel
thinks it's compatible with Uncached-minus. The VRAM mappped by
ioremap_wc() is slightly slower than mapped by ioremap_cache(), but is
still significantly faster than by ioremap().
Change the comment accordingly. Linux VM on ARM64 Hyper-V is still not
working in the latest mainline yet, and when it works in future, the ARM64
support is unlikely to be backported to v5.4 and older, so using
ioremap_wc() in v5.4 and older should be ok.
Note: this fix is only targeted at the stable branches:
v5.4.y, v4.19.y, v4.14.y, v4.9.y and v4.4.y.
Fixes: db49200b1d ("video: hyperv_fb: Fix the cache type when mapping the VRAM")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb25038586 ]
Accesses to dev->xps_cpus_map (when using dev->num_tc) should be
protected by the rtnl lock, like we do for netif_set_xps_queue. I didn't
see an actual bug being triggered, but let's be safe here and take the
rtnl lock while accessing the map in sysfs.
Fixes: 184c449f91 ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59b4a8fa27 ]
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1fef73597f ]
ppp_cp_event is called directly or indirectly by ppp_rx with "ppp->lock"
held. It may call mod_timer to add a new timer. However, at the same time
ppp_timer may be already running and waiting for "ppp->lock". In this
case, there's no need for ppp_timer to continue running and it can just
exit.
If we let ppp_timer continue running, it may call add_timer. This causes
kernel panic because add_timer can't be called with a timer pending.
This patch fixes this problem.
Fixes: e022c2f07a ("WAN: new synchronous PPP implementation for generic HDLC.")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ede3ada3d ]
The function skb_copy() could return NULL, the return value
need to be checked.
Fixes: b5996f11ea ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21fdca22eb ]
RT_TOS() only clears one of the ECN bits. Therefore, when
fib_compute_spec_dst() resorts to a fib lookup, it can return
different results depending on the value of the second ECN bit.
For example, ECT(0) and ECT(1) packets could be treated differently.
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/24 dev veth01
$ ip -netns ns1 address add 192.0.2.11/24 dev veth10
$ ip -netns ns1 address add 192.0.2.21/32 dev lo
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10 src 192.0.2.21
$ ip netns exec ns1 sysctl -wq net.ipv4.icmp_echo_ignore_broadcasts=0
With TOS 4 and ECT(1), ns1 replies using source address 192.0.2.21
(ping uses -Q to set all TOS and ECN bits):
$ ip netns exec ns0 ping -c 1 -b -Q 5 192.0.2.255
[...]
64 bytes from 192.0.2.21: icmp_seq=1 ttl=64 time=0.544 ms
But with TOS 4 and ECT(0), ns1 replies using source address 192.0.2.11
because the "tos 4" route isn't matched:
$ ip netns exec ns0 ping -c 1 -b -Q 6 192.0.2.255
[...]
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.597 ms
After this patch the ECN bits don't affect the result anymore:
$ ip netns exec ns0 ping -c 1 -b -Q 6 192.0.2.255
[...]
64 bytes from 192.0.2.21: icmp_seq=1 ttl=64 time=0.591 ms
Fixes: 35ebf65e85 ("ipv4: Create and use fib_compute_spec_dst() helper.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4614792eeb ]
The CPTS driver registers PTP PHC clock when first netif is going up and
unregister it when all netif are down. Now ethtool will show:
- PTP PHC clock index 0 after boot until first netif is up;
- the last assigned PTP PHC clock index even if PTP PHC clock is not
registered any more after all netifs are down.
This patch ensures that -1 is returned by ethtool when PTP PHC clock is not
registered any more.
Fixes: 8a2c9a5ab4 ("net: ethernet: ti: cpts: rework initialization/deinitialization")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201224162405.28032-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ad58225db ]
Two race conditions can be triggered when storing xps cpus, resulting in
various oops and invalid memory accesses:
1. Calling netdev_set_num_tc while netif_set_xps_queue:
- netif_set_xps_queue uses dev->tc_num as one of the parameters to
compute the size of new_dev_maps when allocating it. dev->tc_num is
also used to access the map, and the compiler may generate code to
retrieve this field multiple times in the function.
- netdev_set_num_tc sets dev->tc_num.
If new_dev_maps is allocated using dev->tc_num and then dev->tc_num
is set to a higher value through netdev_set_num_tc, later accesses to
new_dev_maps in netif_set_xps_queue could lead to accessing memory
outside of new_dev_maps; triggering an oops.
2. Calling netif_set_xps_queue while netdev_set_num_tc is running:
2.1. netdev_set_num_tc starts by resetting the xps queues,
dev->tc_num isn't updated yet.
2.2. netif_set_xps_queue is called, setting up the map with the
*old* dev->num_tc.
2.3. netdev_set_num_tc updates dev->tc_num.
2.4. Later accesses to the map lead to out of bound accesses and
oops.
A similar issue can be found with netdev_reset_tc.
One way of triggering this is to set an iface up (for which the driver
uses netdev_set_num_tc in the open path, such as bnx2x) and writing to
xps_cpus in a concurrent thread. With the right timing an oops is
triggered.
Both issues have the same fix: netif_set_xps_queue, netdev_set_num_tc
and netdev_reset_tc should be mutually exclusive. We do that by taking
the rtnl lock in xps_cpus_store.
Fixes: 184c449f91 ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de33212f76 ]
virtnet_set_channels can recursively call cpus_read_lock if CONFIG_XPS
and CONFIG_HOTPLUG are enabled.
The path is:
virtnet_set_channels - calls get_online_cpus(), which is a trivial
wrapper around cpus_read_lock()
netif_set_real_num_tx_queues
netif_reset_xps_queues_gt
netif_reset_xps_queues - calls cpus_read_lock()
This call chain and potential deadlock happens when the number of TX
queues is reduced.
This commit the removes netif_set_real_num_[tr]x_queues calls from
inside the get/put_online_cpus section, as they don't require that it
be held.
Fixes: 47be24796c ("virtio-net: fix the set affinity bug when CPU IDs are not consecutive")
Signed-off-by: Jeff Dike <jdike@akamai.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20201223025421.671-1-jdike@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1385ae5c30 ]
All the buffers and registers are already set up appropriately for an
MTU slightly above 1500, so we just need to expose this to the
networking stack. AFAICT, there's no need to implement .ndo_change_mtu
when the receive buffers are always set up to support the max_mtu.
This fixes several warnings during boot on our mpc8309-board with an
embedded mv88e6250 switch:
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 0
...
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 4
ucc_geth e0102000.ethernet eth1: error -22 setting MTU to 1504 to include DSA overhead
The last line explains what the DSA stack tries to do: achieving an MTU
of 1500 on-the-wire requires that the master netdevice connected to
the CPU port supports an MTU of 1500+the tagging overhead.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e925e0cd2a ]
ugeth is the netdiv_priv() part of the netdevice. Accessing the memory
pointed to by ugeth (such as done by ucc_geth_memclean() and the two
of_node_puts) after free_netdev() is thus use-after-free.
Fixes: 80a9fad8e8 ("ucc_geth: fix module removal")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cedd1862be ]
Commit 436e980e2e ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).
Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3684566384 ]
Some graphic card has very big memory on chip, such as 32G bytes.
In the following case, it will cause overflow:
pool = gen_pool_create(PAGE_SHIFT, NUMA_NO_NODE);
ret = gen_pool_add(pool, 0x1000000, SZ_32G, NUMA_NO_NODE);
va = gen_pool_alloc(pool, SZ_4G);
The overflow occurs in gen_pool_alloc_algo_owner():
....
size = nbits << order;
....
The @nbits is "int" type, so it will overflow.
Then the gen_pool_avail() will return the wrong value.
This patch converts some "int" to "unsigned long", and
changes the compare code in while.
Link: https://lkml.kernel.org/r/20201229060657.3389-1-sjhuang@iluvatar.ai
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reported-by: Shi Jiasheng <jiasheng.shi@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96d86e6a80 ]
RQF_PREEMPT is used for two different purposes in the legacy IDE code:
1. To mark power management requests.
2. To mark requests that should preempt another request. An (old)
explanation of that feature is as follows: "The IDE driver in the Linux
kernel normally uses a series of busywait delays during its
initialization. When the driver executes these busywaits, the kernel
does nothing for the duration of the wait. The time spent in these
waits could be used for other initialization activities, if they could
be run concurrently with these waits.
More specifically, busywait-style delays such as udelay() in module
init functions inhibit kernel preemption because the Big Kernel Lock is
held, while yielding APIs such as schedule_timeout() allow
preemption. This is true because the kernel handles the BKL specially
and releases and reacquires it across reschedules allowed by the
current thread.
This IDE-preempt specification requires that the driver eliminate these
busywaits and replace them with a mechanism that allows other work to
proceed while the IDE driver is initializing."
Since I haven't found an implementation of (2), do not set the PREEMPT flag
for sense requests. This patch causes sense requests to be postponed while
a drive is suspended instead of being submitted to ide_queue_rq().
If it would ever be necessary to restore the IDE PREEMPT functionality,
that can be done by introducing a new flag in struct ide_request.
Link: https://lore.kernel.org/r/20201209052951.16136-4-bvanassche@acm.org
Cc: David S. Miller <davem@davemloft.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Can Guo <cang@codeaurora.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01341fbd0d ]
In realtime scenario, We do not want to have interference on the
isolated cpu cores. but when invoking alloc_workqueue() for percpu wq
on the housekeeping cpu, it kick a kworker on the isolated cpu.
alloc_workqueue
pwq_adjust_max_active
wake_up_worker
The comment in pwq_adjust_max_active() said:
"Need to kick a worker after thawed or an unbound wq's
max_active is bumped"
So it is unnecessary to kick a kworker for percpu's wq when invoking
alloc_workqueue(). this patch only kick a worker based on the actual
activation of delayed works.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 436e980e2e upstream.
depmod is not guaranteed to be in /sbin, just let make look for
it in the path like all the other invoked programs
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89deb13342 upstream
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc() so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case but
does make the code slightly less fragile so I have included it.
Fixes: 39631b5f95 ("iio: Add Freescale mag3110 magnetometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-4-jic23@kernel.org
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b6b51234d upstream
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable array in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver, depending on which channels are enabled, the timestamp
can be in a number of locations. Hence we cannot use a structure
to specify the data layout without it being misleading.
Fixes: 77c4ad2d6a ("iio: imu: Add initial support for Bosch BMI160")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-6-jic23@kernel.org
[sudip: adjust context and use bmi160_data in old location]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 252bd12563 ]
If emergency system shutdown is called, like by thermal shutdown,
a dm device could be alive when the block device couldn't process
I/O requests anymore. In this state, the handling of I/O errors
by new dm I/O requests or by those already in-flight can lead to
a verity corruption state, which is a misjudgment.
So, skip verity work in response to I/O error when system is shutting
down.
Signed-off-by: Hyeongseok Kim <hyeongseok@gmail.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618de0f4ef ]
The PCM hw_params core function tries to clear up the PCM buffer
before actually using for avoiding the information leak from the
previous usages or the usage before a new allocation. It performs the
memset() with runtime->dma_bytes, but this might still leave some
remaining bytes untouched; namely, the PCM buffer size is aligned in
page size for mmap, hence runtime->dma_bytes doesn't necessarily cover
all PCM buffer pages, and the remaining bytes are exposed via mmap.
This patch changes the memory clearance to cover the all buffer pages
if the stream is supposed to be mmap-ready (that guarantees that the
buffer size is aligned in page size).
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20201218145625.2045-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38dc717e97 ]
Apparently there has been a longstanding race between udev/systemd and
the module loader. Currently, the module loader sends a uevent right
after sysfs initialization, but before the module calls its init
function. However, some udev rules expect that the module has
initialized already upon receiving the uevent.
This race has been triggered recently (see link in references) in some
systemd mount unit files. For instance, the configfs module creates the
/sys/kernel/config mount point in its init function, however the module
loader issues the uevent before this happens. sys-kernel-config.mount
expects to be able to mount /sys/kernel/config upon receipt of the
module loading uevent, but if the configfs module has not called its
init function yet, then this directory will not exist and the mount unit
fails. A similar situation exists for sys-fs-fuse-connections.mount, as
the fuse sysfs mount point is created during the fuse module's init
function. If udev is faster than module initialization then the mount
unit would fail in a similar fashion.
To fix this race, delay the module KOBJ_ADD uevent until after the
module has finished calling its init routine.
References: https://github.com/systemd/systemd/issues/17586
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-By: Nicolas Morey-Chaisemartin <nmoreychaisemartin@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10f04d40a9 ]
The on-disk quota format supports quota files with upto 2^32 blocks. Be
careful when computing quota file offsets in the quota files from block
numbers as they can overflow 32-bit types. Since quota files larger than
4GB would require ~26 millions of quota users, this is mostly a
theoretical concern now but better be careful, fuzzers would find the
problem sooner or later anyway...
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e8ed280da ]
If a module fails to load due to an error in prepare_coming_module(),
the following error handling in load_module() runs with
MODULE_STATE_COMING in module's state. Fix it by correctly setting
MODULE_STATE_GOING under "bug_cleanup" label.
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ebd470370 upstream.
The snd_seq_queue struct contains various flags in the bit fields.
Those are categorized to two different use cases, both of which are
protected by different spinlocks. That implies that there are still
potential risks of the bad operations for bit fields by concurrent
accesses.
For addressing the problem, this patch rearranges those flags to be
a standard bool instead of a bit field.
Reported-by: syzbot+63cbe31877bb80ef58f5@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20201206083456.21110-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5812b32e01 upstream.
Specify type alignment when declaring linker-section match-table entries
to prevent gcc from increasing alignment and corrupting the various
tables with padding (e.g. timers, irqchips, clocks, reserved memory).
This is specifically needed on x86 where gcc (typically) aligns larger
objects like struct of_device_id with static extent on 32-byte
boundaries which at best prevents matching on anything but the first
entry. Specifying alignment when declaring variables suppresses this
optimisation.
Here's a 64-bit example where all entries are corrupt as 16 bytes of
padding has been inserted before the first entry:
ffffffff8266b4b0 D __clk_of_table
ffffffff8266b4c0 d __of_table_fixed_factor_clk
ffffffff8266b5a0 d __of_table_fixed_clk
ffffffff8266b680 d __clk_of_table_sentinel
And here's a 32-bit example where the 8-byte-aligned table happens to be
placed on a 32-byte boundary so that all but the first entry are corrupt
due to the 28 bytes of padding inserted between entries:
812b3ec0 D __irqchip_of_table
812b3ec0 d __of_table_irqchip1
812b3fa0 d __of_table_irqchip2
812b4080 d __of_table_irqchip3
812b4160 d irqchip_of_match_end
Verified on x86 using gcc-9.3 and gcc-4.9 (which uses 64-byte
alignment), and on arm using gcc-7.2.
Note that there are no in-tree users of these tables on x86 currently
(even if they are included in the image).
Fixes: 54196ccbe0 ("of: consolidate linker section OF match table declarations")
Fixes: f6e916b820 ("irqchip: add basic infrastructure")
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201123102319.8090-2-johan@kernel.org
[ johan: adjust context to 5.4 ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a85cbe6159 upstream.
and include <linux/const.h> in UAPI headers instead of <linux/kernel.h>.
The reason is to avoid indirect <linux/sysinfo.h> include when using
some network headers: <linux/netlink.h> or others -> <linux/kernel.h>
-> <linux/sysinfo.h>.
This indirect include causes on MUSL redefinition of struct sysinfo when
included both <sys/sysinfo.h> and some of UAPI headers:
In file included from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/kernel.h:5,
from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/netlink.h:5,
from ../include/tst_netlink.h:14,
from tst_crypto.c:13:
x86_64-buildroot-linux-musl/sysroot/usr/include/linux/sysinfo.h:8:8: error: redefinition of `struct sysinfo'
struct sysinfo {
^~~~~~~
In file included from ../include/tst_safe_macros.h:15,
from ../include/tst_test.h:93,
from tst_crypto.c:11:
x86_64-buildroot-linux-musl/sysroot/usr/include/sys/sysinfo.h:10:8: note: originally defined here
Link: https://lkml.kernel.org/r/20201015190013.8901-1-petr.vorel@gmail.com
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Suggested-by: Rich Felker <dalias@aerifal.cx>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1891ef21d9 ]
fls() and fls64() are using __builtin_ctz() and _builtin_ctzll().
On powerpc, those builtins trivially use ctlzw and ctlzd power
instructions.
Allthough those instructions provide the expected result with
input argument 0, __builtin_ctz() and __builtin_ctzll() are
documented as undefined for value 0.
The easiest fix would be to use fls() and fls64() functions
defined in include/asm-generic/bitops/builtin-fls.h and
include/asm-generic/bitops/fls64.h, but GCC output is not optimal:
00000388 <testfls>:
388: 2c 03 00 00 cmpwi r3,0
38c: 41 82 00 10 beq 39c <testfls+0x14>
390: 7c 63 00 34 cntlzw r3,r3
394: 20 63 00 20 subfic r3,r3,32
398: 4e 80 00 20 blr
39c: 38 60 00 00 li r3,0
3a0: 4e 80 00 20 blr
000003b0 <testfls64>:
3b0: 2c 03 00 00 cmpwi r3,0
3b4: 40 82 00 1c bne 3d0 <testfls64+0x20>
3b8: 2f 84 00 00 cmpwi cr7,r4,0
3bc: 38 60 00 00 li r3,0
3c0: 4d 9e 00 20 beqlr cr7
3c4: 7c 83 00 34 cntlzw r3,r4
3c8: 20 63 00 20 subfic r3,r3,32
3cc: 4e 80 00 20 blr
3d0: 7c 63 00 34 cntlzw r3,r3
3d4: 20 63 00 40 subfic r3,r3,64
3d8: 4e 80 00 20 blr
When the input of fls(x) is a constant, just check x for nullity and
return either 0 or __builtin_clz(x). Otherwise, use cntlzw instruction
directly.
For fls64() on PPC64, do the same but with __builtin_clzll() and
cntlzd instruction. On PPC32, lets take the generic fls64() which
will use our fls(). The result is as expected:
00000388 <testfls>:
388: 7c 63 00 34 cntlzw r3,r3
38c: 20 63 00 20 subfic r3,r3,32
390: 4e 80 00 20 blr
000003a0 <testfls64>:
3a0: 2c 03 00 00 cmpwi r3,0
3a4: 40 82 00 10 bne 3b4 <testfls64+0x14>
3a8: 7c 83 00 34 cntlzw r3,r4
3ac: 20 63 00 20 subfic r3,r3,32
3b0: 4e 80 00 20 blr
3b4: 7c 63 00 34 cntlzw r3,r3
3b8: 20 63 00 40 subfic r3,r3,64
3bc: 4e 80 00 20 blr
Fixes: 2fcff790dc ("powerpc: Use builtin functions for fls()/__fls()/fls64()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/348c2d3f19ffcff8abe50d52513f989c4581d000.1603375524.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5098e77962 ]
The driver must not call tty_wakeup() while holding its private lock as
line disciplines are allowed to call back into write() from
write_wakeup(), leading to a deadlock.
Also remove the unneeded work struct that was used to defer wakeup in
order to work around a possible race in ancient times (see comment about
n_tty write_chan() in commit 14b54e39b4 ("USB: serial: remove
changelogs and old todo entries")).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 658a337a60 ]
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
Cc: stable@vger.kernel.org #5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b8fe4caf ]
In case an error occurs in vfio_pci_enable() before the call to
vfio_pci_probe_mmaps(), vfio_pci_disable() will try to iterate
on an uninitialized list and cause a kernel panic.
Lets move to the initialization to vfio_pci_probe() to fix the
issue.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Fixes: 05f0c03fba ("vfio-pci: Allow to mmap sub-page MMIO BARs if the mmio page is exclusive")
CC: Stable <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a983b5ebee upstream
We've seen memory.stat reads in top-level cgroups take up to fourteen
seconds during a userspace bug that created tens of thousands of ghost
cgroups pinned by lingering page cache.
Even with a more reasonable number of cgroups, aggregating memory.stat
is unnecessarily heavy. The complexity is this:
nr_cgroups * nr_stat_items * nr_possible_cpus
where the stat items are ~70 at this point. With 128 cgroups and 128
CPUs - decent, not enormous setups - reading the top-level memory.stat
has to aggregate over a million per-cpu counters. This doesn't scale.
Instead of spreading the source of truth across all CPUs, use the
per-cpu counters merely to batch updates to shared atomic counters.
This is the same as the per-cpu stocks we use for charging memory to the
shared atomic page_counters, and also the way the global vmstat counters
are implemented.
Vmstat has elaborate spilling thresholds that depend on the number of
CPUs, amount of memory, and memory pressure - carefully balancing the
cost of counter updates with the amount of per-cpu error. That's
because the vmstat counters are system-wide, but also used for decisions
inside the kernel (e.g. NR_FREE_PAGES in the allocator). Neither is
true for the memory controller.
Use the same static batch size we already use for page_counter updates
during charging. The per-cpu error in the stats will be 128k, which is
an acceptable ratio of cores to memory accounting granularity.
[hannes@cmpxchg.org: fix warning in __this_cpu_xchg() calls]
Link: http://lkml.kernel.org/r/20171201135750.GB8097@cmpxchg.org
Link: http://lkml.kernel.org/r/20171103153336.24044-3-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
[shaoyi@amazon.com: resolved the conflict brought by commit 17ffa29c35 in mm/memcontrol.c by contextual fix]
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d1b71226d upstream
The altsetting sanity check in set_sync_ep_implicit_fb_quirk() was
checking for there to be at least one altsetting but then went on to
access the second one, which may not exist.
This could lead to random slab data being used to initialise the sync
endpoint in snd_usb_add_endpoint().
Fixes: c75a8a7ae5 ("ALSA: snd-usb: add support for implicit feedback")
Fixes: ca10a7ebdf ("ALSA: usb-audio: FT C400 sync playback EP to capture EP")
Fixes: 5e35dc0338 ("ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204")
Fixes: 17f08b0d9a ("ALSA: usb-audio: add implicit fb quirk for Axe-Fx II")
Fixes: 103e962564 ("ALSA: usb-audio: simplify set_sync_ep_implicit_fb_quirk")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200114083953.1106-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93decc5636 upstream.
In __make_request() a new r10bio is allocated and passed to
raid10_read_request(). The read_slot member of the bio is not
initialized, and the raid10_read_request() uses it to index an
array. This leads to occasional panics.
Fix by initializing the field to invalid value and checking for
valid value in raid10_read_request().
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Vigor <kvigor@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4684709bf8 upstream.
If kobject_init_and_add() fails, pci_slot_release() is called to delete
slot->list from parent->slots. But slot->list hasn't been initialized
yet, so we dereference a NULL pointer:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
...
CPU: 10 PID: 1 Comm: swapper/0 Not tainted 4.4.240 #197
task: ffffeb398a45ef10 task.stack: ffffeb398a470000
PC is at __list_del_entry_valid+0x5c/0xb0
LR is at pci_slot_release+0x84/0xe4
...
__list_del_entry_valid+0x5c/0xb0
pci_slot_release+0x84/0xe4
kobject_put+0x184/0x1c4
pci_create_slot+0x17c/0x1b4
__pci_hp_initialize+0x68/0xa4
pciehp_probe+0x1a4/0x2fc
pcie_port_probe_service+0x58/0x84
driver_probe_device+0x320/0x470
Initialize slot->list before calling kobject_init_and_add() to avoid this.
Fixes: 8a94644b44 ("PCI: Fix pci_create_slot() reference count leak")
Link: https://lore.kernel.org/r/1606876422-117457-1-git-send-email-zhongjubin@huawei.com
Signed-off-by: Jubin Zhong <zhongjubin@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dd2a1740e upstream.
A recent change to ndctl to attempt to reconfigure namespaces in place
uncovered a label accounting problem in block-window-type namespaces.
The ndctl "create.sh" test is able to trigger this signature:
WARNING: CPU: 34 PID: 9167 at drivers/nvdimm/label.c:1100 __blk_label_update+0x9a3/0xbc0 [libnvdimm]
[..]
RIP: 0010:__blk_label_update+0x9a3/0xbc0 [libnvdimm]
[..]
Call Trace:
uuid_store+0x21b/0x2f0 [libnvdimm]
kernfs_fop_write+0xcf/0x1c0
vfs_write+0xcc/0x380
ksys_write+0x68/0xe0
When allocated capacity for a namespace is renamed (new UUID) the labels
with the old UUID need to be deleted. The ndctl behavior to always
destroy namespaces on reconfiguration hid this problem.
The immediate impact of this bug is limited since block-window-type
namespaces only seem to exist in the specification and not in any
shipping products. However, the label handling code is being reused for
other technologies like CXL region labels, so there is a benefit to
making sure both vertical labels sets (block-window) and horizontal
label sets (pmem) have a functional reference implementation in
libnvdimm.
Fixes: c4703ce11c ("libnvdimm/namespace: Fix label tracking error")
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9996bd4947 upstream.
'xenbus_backend' watches 'state' of devices, which is writable by
guests. Hence, if guests intensively updates it, dom0 will have lots of
pending events that exhausting memory of dom0. In other words, guests
can trigger dom0 memory pressure. This is known as XSA-349. However,
the watch callback of it, 'frontend_changed()', reads only 'state', so
doesn't need to have the pending events.
To avoid the problem, this commit disallows pending watch messages for
'xenbus_backend' using the 'will_handle()' watch callback.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dc86ca6b4 upstream.
This commit adds a counter of pending messages for each watch in the
struct. It is used to skip unnecessary pending messages lookup in
'unregister_xenbus_watch()'. It could also be used in 'will_handle'
callback.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e85d32b1c upstream.
Some code does not directly make 'xenbus_watch' object and call
'register_xenbus_watch()' but use 'xenbus_watch_path()' instead. This
commit adds support of 'will_handle' callback in the
'xenbus_watch_path()' and it's wrapper, 'xenbus_watch_pathfmt()'.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fed1755b11 upstream.
If handling logics of watch events are slower than the events enqueue
logic and the events can be created from the guests, the guests could
trigger memory pressure by intensively inducing the events, because it
will create a huge number of pending events that exhausting the memory.
Fortunately, some watch events could be ignored, depending on its
handler callback. For example, if the callback has interest in only one
single path, the watch wouldn't want multiple pending events. Or, some
watches could ignore events to same path.
To let such watches to volutarily help avoiding the memory pressure
situation, this commit introduces new watch callback, 'will_handle'. If
it is not NULL, it will be called for each new event just before
enqueuing it. Then, if the callback returns false, the event will be
discarded. No watch is using the callback for now, though.
This is part of XSA-349
Cc: stable@vger.kernel.org
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reported-by: Michael Kurth <mku@amazon.de>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c728719a4 upstream.
When xen_blkif_disconnect() is called, the kernel thread behind the
block interface is stopped by calling kthread_stop(ring->xenblkd).
The ring->xenblkd thread pointer being non-NULL determines if the
thread has been already stopped.
Normally, the thread's function xen_blkif_schedule() sets the
ring->xenblkd to NULL, when the thread's main loop ends.
However, when the thread has not been started yet (i.e.
wake_up_process() has not been called on it), the xen_blkif_schedule()
function would not be called yet.
In such case the kthread_stop() call returns -EINTR and the
ring->xenblkd remains dangling.
When this happens, any consecutive call to xen_blkif_disconnect (for
example in frontend_changed() callback) leads to a kernel crash in
kthread_stop() (e.g. NULL pointer dereference in exit_creds()).
This is XSA-350.
Cc: <stable@vger.kernel.org> # 4.12
Fixes: a24fa22ce2 ("xen/blkback: don't use xen_blkif_get() in xen-blkback kthread")
Reported-by: Olivier Benjamin <oliben@amazon.com>
Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Signed-off-by: Pawel Wieczorkiewicz <wipawel@amazon.de>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bca5b06580 upstream.
md-cluster uses MD_CLUSTER_SEND_LOCK to make node can exclusively send msg.
During sending msg, node can concurrently receive msg from another node.
When node does resync job, grab token_lockres:EX may trigger a deadlock:
```
nodeA nodeB
-------------------- --------------------
a.
send METADATA_UPDATED
held token_lockres:EX
b.
md_do_sync
resync_info_update
send RESYNCING
+ set MD_CLUSTER_SEND_LOCK
+ wait for holding token_lockres:EX
c.
mdadm /dev/md0 --remove /dev/sdg
+ held reconfig_mutex
+ send REMOVE
+ wait_event(MD_CLUSTER_SEND_LOCK)
d.
recv_daemon //METADATA_UPDATED from A
process_metadata_update
+ (mddev_trylock(mddev) ||
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD)
//this time, both return false forever
```
Explaination:
a. A send METADATA_UPDATED
This will block another node to send msg
b. B does sync jobs, which will send RESYNCING at intervals.
This will be block for holding token_lockres:EX lock.
c. B do "mdadm --remove", which will send REMOVE.
This will be blocked by step <b>: MD_CLUSTER_SEND_LOCK is 1.
d. B recv METADATA_UPDATED msg, which send from A in step <a>.
This will be blocked by step <c>: holding mddev lock, it makes
wait_event can't hold mddev lock. (btw,
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD keep ZERO in this scenario.)
There is a similar deadlock in commit 0ba959774e
("md-cluster: use sync way to handle METADATA_UPDATED msg")
In that commit, step c is "update sb". This patch step c is
"mdadm --remove".
For fixing this issue, we can refer the solution of function:
metadata_update_start. Which does the same grab lock_token action.
lock_comm can use the same steps to avoid deadlock. By moving
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD from lock_token to lock_comm.
It enlarge a little bit window of MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD,
but it is safe & can break deadlock.
Repro steps (I only triggered 3 times with hundreds tests):
two nodes share 3 iSCSI luns: sdg/sdh/sdi. Each lun size is 1GB.
```
ssh root@node2 "mdadm -S --scan"
mdadm -S --scan
for i in {g,h,i};do dd if=/dev/zero of=/dev/sd$i oflag=direct bs=1M \
count=20; done
mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sdg /dev/sdh \
--bitmap-chunk=1M
ssh root@node2 "mdadm -A /dev/md0 /dev/sdg /dev/sdh"
sleep 5
mkfs.xfs /dev/md0
mdadm --manage --add /dev/md0 /dev/sdi
mdadm --wait /dev/md0
mdadm --grow --raid-devices=3 /dev/md0
mdadm /dev/md0 --fail /dev/sdg
mdadm /dev/md0 --remove /dev/sdg
mdadm --grow --raid-devices=2 /dev/md0
```
test script will hung when executing "mdadm --remove".
```
# dump stacks by "echo t > /proc/sysrq-trigger"
md0_cluster_rec D 0 5329 2 0x80004000
Call Trace:
__schedule+0x1f6/0x560
? _cond_resched+0x2d/0x40
? schedule+0x4a/0xb0
? process_metadata_update.isra.0+0xdb/0x140 [md_cluster]
? wait_woken+0x80/0x80
? process_recvd_msg+0x113/0x1d0 [md_cluster]
? recv_daemon+0x9e/0x120 [md_cluster]
? md_thread+0x94/0x160 [md_mod]
? wait_woken+0x80/0x80
? md_congested+0x30/0x30 [md_mod]
? kthread+0x115/0x140
? __kthread_bind_mask+0x60/0x60
? ret_from_fork+0x1f/0x40
mdadm D 0 5423 1 0x00004004
Call Trace:
__schedule+0x1f6/0x560
? __schedule+0x1fe/0x560
? schedule+0x4a/0xb0
? lock_comm.isra.0+0x7b/0xb0 [md_cluster]
? wait_woken+0x80/0x80
? remove_disk+0x4f/0x90 [md_cluster]
? hot_remove_disk+0xb1/0x1b0 [md_mod]
? md_ioctl+0x50c/0xba0 [md_mod]
? wait_woken+0x80/0x80
? blkdev_ioctl+0xa2/0x2a0
? block_ioctl+0x39/0x40
? ksys_ioctl+0x82/0xc0
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x5f/0x150
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
md0_resync D 0 5425 2 0x80004000
Call Trace:
__schedule+0x1f6/0x560
? schedule+0x4a/0xb0
? dlm_lock_sync+0xa1/0xd0 [md_cluster]
? wait_woken+0x80/0x80
? lock_token+0x2d/0x90 [md_cluster]
? resync_info_update+0x95/0x100 [md_cluster]
? raid1_sync_request+0x7d3/0xa40 [raid1]
? md_do_sync.cold+0x737/0xc8f [md_mod]
? md_thread+0x94/0x160 [md_mod]
? md_congested+0x30/0x30 [md_mod]
? kthread+0x115/0x140
? __kthread_bind_mask+0x60/0x60
? ret_from_fork+0x1f/0x40
```
At last, thanks for Xiao's solution.
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Heming <heming.zhao@suse.com>
Suggested-by: Xiao Ni <xni@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198cf32f05 upstream.
Whilst this is another case of the issue Lars reported with
an array of elements of smaller than 8 bytes being passed
to iio_push_to_buffers_with_timestamp(), the solution here is
a bit different from the other cases and relies on __aligned
working on the stack (true since 4.6?)
This one is unusual. We have to do an explicit memset() each time
as we are reading 3 bytes into a potential 4 byte channel which
may sometimes be a 2 byte channel depending on what is enabled.
As such, moving the buffer to the heap in the iio_priv structure
doesn't save us much. We can't use a nice explicit structure
on the stack either as the data channels have different storage
sizes and are all separately controlled.
Fixes: cc26ad455f ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-7-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a61817216b upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc() so no data can leak apart
from previous readings and in this case the status byte from the device.
The forced alignment of ts is not necessary in this case but it
potentially makes the code less fragile.
>From personal communications with Mikko:
We could probably split the reading of the int register, but it
would mean a significant performance cost of 20 i2c clock cycles.
Fixes: e12ffd241c ("iio: light: rpr0521 triggered buffer")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-2-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19ef7b70ca upstream.
When updating the buffer demux, we will skip a scan element from the
device in the case `in_ind != out_ind` and we enter the while loop.
in_ind should only be refreshed with `find_next_bit()` in the end of the
loop.
Note, to cause problems we need a situation where we are skippig over
an element (channel not enabled) that happens to not have the same size
as the next element. Whilst this is a possible situation we haven't
actually identified any cases in mainline where it happens as most drivers
have consistent channel storage sizes with the exception of the timestamp
which is the last element and hence never skipped over.
Fixes: 5ada4ea9be ("staging:iio: add demux optionally to path from device to buffer")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20201112144323.28887-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 639a82434f upstream.
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa0227 ("mtd: parser: cmdline: Support MTD names containing one or more colons")
Cc: stable@vger.kernel.org
Cc: Ron Minnich <rminnich@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c61b3e4839 upstream.
Bounds checking tools can flag a bug in dbAdjTree() for an array index
out of bounds in dmt_stree. Since dmt_stree can refer to the stree in
both structures dmaptree and dmapctl, use the larger array to eliminate
the false positive.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9afc9a8a49 upstream.
The log of this problem is:
jffs2: Error garbage collecting node at 0x***!
jffs2: No space for garbage collection. Aborting GC thread
This is because GC believe that it do nothing, so it abort.
After going over the image of jffs2, I find a scene that
can trigger this problem stably.
The scene is: there is a normal dirent node at summary-area,
but abnormal at corresponding not-summary-area with error
name_crc.
The reason that GC exit abnormally is because it find that
abnormal dirent node to GC, but when it goes to function
jffs2_add_fd_to_list, it cannot meet the condition listed
below:
if ((*prev)->nhash == new->nhash && !strcmp((*prev)->name, new->name))
So no node is marked obsolete, statistical information of
erase_block do not change, which cause GC exit abnormally.
The root cause of this problem is: we do not check the
name_crc of the abnormal dirent node with summary is enabled.
Noticed that in function jffs2_scan_dirent_node, we use
function jffs2_scan_dirty_space to deal with the dirent
node with error name_crc. So this patch add a checking
code in function read_direntry to ensure the correctness
of dirent node. If checked failed, the dirent node will
be marked obsolete so GC will pass this node and this
problem will be fixed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhe Li <lizhe67@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5cafce3ad upstream.
A NULL pointer dereference may occur in __ceph_remove_cap with some of the
callbacks used in ceph_iterate_session_caps, namely trim_caps_cb and
remove_session_caps_cb. Those callers hold the session->s_mutex, so they
are prevented from concurrent execution, but ceph_evict_inode does not.
Since the callers of this function hold the i_ceph_lock, the fix is simply
a matter of returning immediately if caps->ci is NULL.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/43272
Suggested-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 207cdd565d upstream.
Commit a408e4a86b ("ima: open a new file instance if no read
permissions") already introduced a second open to measure a file when the
original file descriptor does not allow it. However, it didn't remove the
existing method of changing the mode of the original file descriptor, which
is still necessary if the current process does not have enough privileges
to open a new one.
Changing the mode isn't really an option, as the filesystem might need to
do preliminary steps to make the read possible. Thus, this patch removes
the code and keeps the second open as the only option to measure a file
when it is unreadable with the original file descriptor.
Cc: <stable@vger.kernel.org> # 4.20.x: 0014cc04e8 ima: Set file->f_mode
Fixes: 2fe5d6def1 ("ima: integrity appraisal extension")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f10881a46f upstream.
Commit bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
introduced the following error when invoking the errinjct userspace
tool:
[root@ltcalpine2-lp5 librtas]# errinjct open
[327884.071171] sys_rtas: RTAS call blocked - exploit attempt?
[327884.071186] sys_rtas: token=0x26, nargs=0 (called by errinjct)
errinjct: Could not open RTAS error injection facility
errinjct: librtas: open: Unexpected I/O error
The entry for ibm,open-errinjct in rtas_filter array has a typo where
the "j" is omitted in the rtas call name. After fixing this typo the
errinjct tool functions again as expected.
[root@ltcalpine2-lp5 linux]# errinjct open
RTAS error injection facility open, token = 1
Fixes: bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201208195434.8289-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b8350ae9 upstream.
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46e294efc3 upstream.
Xattr code using inodes with large xattr data can end up dropping last
inode reference (and thus deleting the inode) from places like
ext4_xattr_set_entry(). That function is called with transaction started
and so ext4_evict_inode() can deadlock against fs freezing like:
CPU1 CPU2
removexattr() freeze_super()
vfs_removexattr()
ext4_xattr_set()
handle = ext4_journal_start()
...
ext4_xattr_set_entry()
iput(old_ea_inode)
ext4_evict_inode(old_ea_inode)
sb->s_writers.frozen = SB_FREEZE_FS;
sb_wait_write(sb, SB_FREEZE_FS);
ext4_freeze()
jbd2_journal_lock_updates()
-> blocks waiting for all
handles to stop
sb_start_intwrite()
-> blocks as sb is already in SB_FREEZE_FS state
Generally it is advisable to delete inodes from a separate transaction
as it can consume quite some credits however in this case it would be
quite clumsy and furthermore the credits for inode deletion are quite
limited and already accounted for. So just tweak ext4_evict_inode() to
avoid freeze protection if we have transaction already started and thus
it is not really needed anyway.
Cc: stable@vger.kernel.org
Fixes: dec214d00e ("ext4: xattr inode deduplication")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Link: https://lore.kernel.org/r/20201127110649.24730-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cca4155372 upstream.
When freeing metadata, we will create an ext4_free_data and
insert it into the pending free list. After the current
transaction is committed, the object will be freed.
ext4_mb_free_metadata() will check whether the area to be freed
overlaps with the pending free list. If true, return directly. At this
time, ext4_free_data is leaked. Fortunately, the probability of this
problem is small, since it only occurs if the file system is corrupted
such that a block is claimed by more one inode and those inodes are
deleted within a single jbd2 transaction.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Link: https://lore.kernel.org/r/1604764698-4269-8-git-send-email-brookxu@tencent.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f7fec0ba8 upstream
Some of the self tests create a test inode, setup some extents and then do
calls to btrfs_get_extent() to test that the corresponding extent maps
exist and are correct. However btrfs_get_extent(), since the 5.2 merge
window, now errors out when it finds a regular or prealloc extent for an
inode that does not correspond to a regular file (its ->i_mode is not
S_IFREG). This causes the self tests to fail sometimes, specially when
KASAN, slub_debug and page poisoning are enabled:
$ modprobe btrfs
modprobe: ERROR: could not insert 'btrfs': Invalid argument
$ dmesg
[ 9414.691648] Btrfs loaded, crc32c=crc32c-intel, debug=on, assert=on, integrity-checker=on, ref-verify=on
[ 9414.692655] BTRFS: selftest: sectorsize: 4096 nodesize: 4096
[ 9414.692658] BTRFS: selftest: running btrfs free space cache tests
[ 9414.692918] BTRFS: selftest: running extent only tests
[ 9414.693061] BTRFS: selftest: running bitmap only tests
[ 9414.693366] BTRFS: selftest: running bitmap and extent tests
[ 9414.696455] BTRFS: selftest: running space stealing from bitmap to extent tests
[ 9414.697131] BTRFS: selftest: running extent buffer operation tests
[ 9414.697133] BTRFS: selftest: running btrfs_split_item tests
[ 9414.697564] BTRFS: selftest: running extent I/O tests
[ 9414.697583] BTRFS: selftest: running find delalloc tests
[ 9415.081125] BTRFS: selftest: running find_first_clear_extent_bit test
[ 9415.081278] BTRFS: selftest: running extent buffer bitmap tests
[ 9415.124192] BTRFS: selftest: running inode tests
[ 9415.124195] BTRFS: selftest: running btrfs_get_extent tests
[ 9415.127909] BTRFS: selftest: running hole first btrfs_get_extent test
[ 9415.128343] BTRFS critical (device (efault)): regular/prealloc extent found for non-regular inode 256
[ 9415.131428] BTRFS: selftest: fs/btrfs/tests/inode-tests.c:904 expected a real extent, got 0
This happens because the test inodes are created without ever initializing
the i_mode field of the inode, and neither VFS's new_inode() nor the btrfs
callback btrfs_alloc_inode() initialize the i_mode. Initialization of the
i_mode is done through the various callbacks used by the VFS to create
new inodes (regular files, directories, symlinks, tmpfiles, etc), which
all call btrfs_new_inode() which in turn calls inode_init_owner(), which
sets the inode's i_mode. Since the tests only uses new_inode() to create
the test inodes, the i_mode was never initialized.
This always happens on a VM I used with kasan, slub_debug and many other
debug facilities enabled. It also happened to someone who reported this
on bugzilla (on a 5.3-rc).
Fix this by setting i_mode to S_IFREG at btrfs_new_test_inode().
Fixes: 6bf9e4bd6a ("btrfs: inode: Verify inode mode to avoid NULL pointer dereference")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204397
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 320f9028c7 upstream.
The driver did not update its view of the available device buffer space
until write() was called in task context. This meant that write_room()
would return 0 even after the device had sent a write-unthrottle
notification, something which could lead to blocked writers not being
woken up (e.g. when using OPOST).
Note that we must also request an unthrottle notification is case a
write() request fills the device buffer exactly.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49fbb8e37a upstream.
The driver's transmit-unthrottle work was never flushed on disconnect,
something which could lead to the driver port data being freed while the
unthrottle work is still scheduled.
Fix this by cancelling the unthrottle work when shutting down the port.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37faf50615 upstream.
The driver's deferred write wakeup was never flushed on disconnect,
something which could lead to the driver port data being freed while the
wakeup work is still scheduled.
Fix this by using the usb-serial write wakeup which gets cancelled
properly on disconnect.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c01d2c5869 upstream.
Make sure to clear the write-busy flag also in case no new data was
submitted due to lack of device buffer space so that writing is
resumed once space again becomes available.
Fixes: 507ca9bc04 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7353cad7ee upstream.
The write() callback can be called in interrupt context (e.g. when used
as a console) so interrupts must be disabled while holding the port lock
to prevent a possible deadlock.
Fixes: e81ee637e4 ("usb-serial: possible irq lock inversion (PPP vs. usb/serial)")
Fixes: 507ca9bc04 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 696c541c8c upstream.
Commit c528fcb116 ("USB: serial: keyspan_pda: fix receive sanity
checks") broke write-unthrottle handling by dropping well-formed
unthrottle-interrupt packets which are precisely two bytes long. This
could lead to blocked writers not being woken up when buffer space again
becomes available.
Instead, stop unconditionally printing the third byte which is
(presumably) only valid on modem-line changes.
Fixes: c528fcb116 ("USB: serial: keyspan_pda: fix receive sanity checks")
Cc: stable <stable@vger.kernel.org> # 4.11
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 975323ab8f upstream.
The parallel-port restore operations is called when a driver claims the
port and is supposed to restore the provided state (e.g. saved when
releasing the port).
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 706657b1fe upstream.
In order to setup its PCI component, the driver needs any node private
instance in order to get a reference to the PCI device and hand that
into edac_pci_create_generic_ctl(). For convenience, it uses the 0th
memory controller descriptor under the assumption that if any, the 0th
will be always present.
However, this assumption goes wrong when the 0th node doesn't have
memory and the driver doesn't initialize an instance for it:
EDAC amd64: F17h detected (node 0).
...
EDAC amd64: Node 0: No DIMMs detected.
But looking up node instances is not really needed - all one needs is
the pointer to the proper device which gets discovered during instance
init.
So stash that pointer into a variable and use it when setting up the
EDAC PCI component.
Clear that variable when the driver needs to unwind due to some
instances failing init to avoid any registration imbalance.
Cc: <stable@vger.kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201122150815.13808-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17858b140b upstream.
ecdh_set_secret() casts a void* pointer to a const u64* in order to
feed it into ecc_is_key_valid(). This is not generally permitted by
the C standard, and leads to actual misalignment faults on ARMv6
cores. In some cases, these are fixed up in software, but this still
leads to performance hits that are entirely avoidable.
So let's copy the key into the ctx buffer first, which we will do
anyway in the common case, and which guarantees correct alignment.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56c90457eb upstream.
I have had reports from two different people that attempts to read the
analog input channels of the MF624 board fail with an `ETIMEDOUT` error.
After triggering the conversion, the code calls `comedi_timeout()` with
`mf6x4_ai_eoc()` as the callback function to check if the conversion is
complete. The callback returns 0 if complete or `-EBUSY` if not yet
complete. `comedi_timeout()` returns `-ETIMEDOUT` if it has not
completed within a timeout period which is propagated as an error to the
user application.
The existing code considers the conversion to be complete when the EOLC
bit is high. However, according to the user manuals for the MF624 and
MF634 boards, this test is incorrect because EOLC is an active low
signal that goes high when the conversion is triggered, and goes low
when the conversion is complete. Fix the problem by inverting the test
of the EOLC bit state.
Fixes: 04b565021a ("comedi: Humusoft MF634 and MF624 DAQ cards driver")
Cc: <stable@vger.kernel.org> # v4.4+
Cc: Rostislav Lisovy <lisovy@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20201207145806.4046-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a7f65583 upstream.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ede91f83a upstream.
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a29ea01653 upstream.
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5e438ebd7 upstream.
Not resetting the SMT siblings might leave them in unpredictable
state. One of the observed problems was that the CPU timer wasn't
reset and therefore large system time values where accounted during
CPU bringup.
Cc: <stable@kernel.org> # 4.0
Fixes: 10ad34bc76 ("s390: add SMT support")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08221c40f upstream.
Recently we met a touchscreen problem on some Thinkpad machines, the
touchscreen driver (i2c-hid) is not loaded and the touchscreen can't
work.
An i2c ACPI device with the name WACF2200 is defined in the BIOS, with
the current rule in matching_id(), this device will be regarded as
a PNP device since there is WACFXXX in the acpi_pnp_device_ids[] and
this PNP device is attached to the acpi device as the 1st
physical_node, this will make the i2c bus match fail when i2c bus
calls acpi_companion_match() to match the acpi_id_table in the i2c-hid
driver.
WACF2200 is an i2c device instead of a PNP device, after adding the
string length comparing, the matching_id() will return false when
matching WACF2200 and WACFXXX, and it is reasonable to compare the
string length when matching two IDs.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12fc4dad94 upstream.
This reverts commit 8a66790b78.
Switching this function to AE_CTRL_TERMINATE broke the documented
behaviour of acpi_dev_get_resources() - AE_CTRL_TERMINATE does not, in
fact, terminate the resource walk because acpi_walk_resource_buffer()
ignores it (specifically converting it to AE_OK), referring to that
value as "an OK termination by the user function". This means that
acpi_dev_get_resources() does not abort processing when the preproc
function returns a negative value.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7482c5cb90 upstream.
The idea behind acpi_pm_set_bridge_wakeup() was to allow bridges to
be reference counted for wakeup enabling, because they may be enabled
to signal wakeup on behalf of their subordinate devices and that
may happen for multiple times in a row, whereas for the other devices
it only makes sense to enable wakeup signaling once.
However, this becomes problematic if the bridge itself is suspended,
because it is treated as a "regular" device in that case and the
reference counting doesn't work.
For instance, suppose that there are two devices below a bridge and
they both can signal wakeup. Every time one of them is suspended,
wakeup signaling is enabled for the bridge, so when they both have
been suspended, the bridge's wakeup reference counter value is 2.
Say that the bridge is suspended subsequently and acpi_pci_wakeup()
is called for it. Because the bridge can signal wakeup, that
function will invoke acpi_pm_set_device_wakeup() to configure it
and __acpi_pm_set_device_wakeup() will be called with the last
argument equal to 1. This causes __acpi_device_wakeup_enable()
invoked by it to omit the reference counting, because the reference
counter of the target device (the bridge) is 2 at that time.
Now say that the bridge resumes and one of the device below it
resumes too, so the bridge's reference counter becomes 0 and
wakeup signaling is disabled for it, but there is still the other
suspended device which may need the bridge to signal wakeup on its
behalf and that is not going to work.
To address this scenario, use wakeup enable reference counting for
all devices, not just for bridges, so drop the last argument from
__acpi_device_wakeup_enable() and __acpi_pm_set_device_wakeup(),
which causes acpi_pm_set_device_wakeup() and
acpi_pm_set_bridge_wakeup() to become identical, so drop the latter
and use the former instead of it everywhere.
Fixes: 1ba51a7c14 ("ACPI / PCI / PM: Rework acpi_pci_propagate_wakeup()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f051ae4f6c upstream.
gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:
drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
40 | *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
569 | } __packed cmd;
| ^~~
Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.
Fixes: c2c06c41f7 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e297ddf296 upstream.
If the call to spi_register_master() fails on probe of the NetUP
Universal DVB driver, the spi_master struct is erroneously not freed.
Likewise, if spi_new_device() fails, the spi_controller struct is
not unregistered. Plug the leaks.
While at it, fix an ordering issue in netup_spi_release() wherein
spi_unregister_master() is called after fiddling with the IRQ control
register. The correct order is to call spi_unregister_master() *before*
this teardown step because bus accesses may still be ongoing until that
function returns.
Fixes: 52b1eaf4c5 ("[media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: <stable@vger.kernel.org> # v4.3+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.3+
Cc: Kozlov Sergey <serjk@netup.ru>
Link: https://lore.kernel.org/r/c4c24f333fc7840f4a3db24789e6e10dd660bede.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f56df4c8f upstream.
If a user holds a button down on a remote, then no ir idle interrupt will
be generated until the user releases the button, depending on how quickly
the remote repeats. No IR is processed until that point, which means that
holding down a button may not do anything.
This also resolves an issue on a Cubieboard 1 where the IR receiver is
picking up ambient infrared as IR and spews out endless
"rc rc0: IR event FIFO is full!" messages unless you choose to live in
the dark.
Cc: stable@vger.kernel.org
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e469d0b09a upstream.
The gspca driver leaks memory when a probe fails. gspca_dev_probe2()
calls v4l2_device_register(), which takes a reference to the
underlying device node (in this case, a USB interface). But the
failure pathway neglects to call v4l2_device_unregister(), the routine
responsible for dropping this reference. Consequently the memory for
the USB interface and its device never gets released.
This patch adds the missing function call.
Reported-and-tested-by: syzbot+44e64397bd81d5e84cba@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 80db2a087f ]
To let userspace know what 'scancodes' should be used in EVIOCGKEYCODE
and EVIOCSKEYCODE ioctls, we should send EV_MSC/MSC_SCAN events in
addition to EV_KEY/KEY_* events. The driver already declared MSC_SCAN
capability, so it is only matter of actually sending the events.
Link: https://lore.kernel.org/r/X87aOaSptPTvZ3nZ@google.com
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed9b25d197 ]
Namespaced file capabilities were introduced in 8db6c34f1d .
When userspace reads an xattr for a namespaced capability, a
virtualized representation of it is returned if the caller is
in a user namespace owned by the capability's owning rootid.
The function which performs this virtualization was not hooked
up if CONFIG_SECURITY=n. Therefore in that case the original
xattr was shown instead of the virtualized one.
To test this using libcap-bin (*1),
$ v=$(mktemp)
$ unshare -Ur setcap cap_sys_admin-eip $v
$ unshare -Ur setcap -v cap_sys_admin-eip $v
/tmp/tmp.lSiIFRvt8Y: OK
"setcap -v" verifies the values instead of setting them, and
will check whether the rootid value is set. Therefore, with
this bug un-fixed, and with CONFIG_SECURITY=n, setcap -v will
fail:
$ v=$(mktemp)
$ unshare -Ur setcap cap_sys_admin=eip $v
$ unshare -Ur setcap -v cap_sys_admin=eip $v
nsowner[got=1000, want=0],/tmp/tmp.HHDiOOl9fY differs in []
Fix this bug by calling cap_inode_getsecurity() in
security_inode_getsecurity() instead of returning
-EOPNOTSUPP, when CONFIG_SECURITY=n.
*1 - note, if libcap is too old for getcap to have the '-n'
option, then use verify-caps instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209689
Cc: Hervé Guillemet <herve@guillemet.org>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Serge Hallyn <shallyn@cisco.com>
Signed-off-by: Andrew G. Morgan <morgan@kernel.org>
Signed-off-by: James Morris <jamorris@linux.microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f0f1e80fd ]
When there are other PWM controllers enabled along with pwm-lp3943,
pwm-lp3942 is failing to probe with -EEXIST error. This is because
other PWM controllers are probed first and assigned PWM base 0 and
pwm-lp3943 is requesting for 0 again.
In order to avoid this, assign the chip base with -1, so that it is
dynamically allocated.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Uwe Kleine-König <u.kleine-könig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36c47df85e ]
clang produces a build failure in configurations without COMMON_CLK
when a timeout calculation goes wrong:
arm-linux-gnueabi-ld: drivers/watchdog/coh901327_wdt.o: in function `coh901327_enable':
coh901327_wdt.c:(.text+0x50): undefined reference to `__bad_udelay'
Add a Kconfig dependency to only do build testing when COMMON_CLK
is enabled.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201203223358.1269372-1-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9431f7c199 ]
xterm serial channel was leaking a fd used in setting up the
port helper
This bug is prehistoric - it predates switching to git. The "fixes"
header here is really just to mark all the versions we would like this to
apply to which is "Anything from the Cretaceous period onwards".
No dinosaurs were harmed in fixing this bug.
Fixes: b40997b872 ("um: drivers/xterm.c: fix a file descriptor leak")
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1efdb604f ]
The platform device driver name is "max77693-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: db1b903742 ("extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bf5861d6e ]
The periph_clks[] array contains duplicated entry for Security Engine
clock which was meant to be defined for T210, but it wasn't added
properly. This patch corrects the T210 SE entry and fixes the following
error message on T114/T124: "Tegra clk 127: register failed with -17".
Fixes: dc37fec483 ("clk: tegra: periph: Add new periph clks and muxes for Tegra210")
Tested-by Nicolas Chauvet <kwizart@gmail.com>
Reported-by Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201025224212.7790-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78ff2733ff ]
Fix to restore BTF if single-stepping causes a page fault and
it is cancelled.
Usually the BTF flag was restored when the single stepping is done
(in resume_execution()). However, if a page fault happens on the
single stepping instruction, the fault handler is invoked and
the single stepping is cancelled. Thus, the BTF flag is not
restored.
Fixes: 1ecc798c67 ("x86: debugctlmsr kprobes")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/160389546985.106936.12727996109376240993.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4420440c57 ]
The warning message from nfsd terminating normally
can confuse system adminstrators or monitoring software.
Though it's not exactly fair to pin-point a commit where it
originated, the current form in the current place started
to appear in:
Fixes: e096bbc648 ("knfsd: remove special handling for SIGHUP")
Signed-off-by: kazuo ito <kzpn200@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b866459489 ]
Partitions with cache nodes in the device tree can encounter the
following warning on resume:
CPU 0 already accounted in PowerPC,POWER9@0(Data)
WARNING: CPU: 0 PID: 3177 at arch/powerpc/kernel/cacheinfo.c:197 cacheinfo_cpu_online+0x640/0x820
These calls to cacheinfo_cpu_offline/online have been redundant since
commit e610a466d1 ("powerpc/pseries/mobility: rebuild cacheinfo
hierarchy post-migration").
Fixes: e610a466d1 ("powerpc/pseries/mobility: rebuild cacheinfo hierarchy post-migration")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201207215200.1785968-25-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52719fce3f ]
There are three ways pseries_suspend_begin() can be reached:
1. When "mem" is written to /sys/power/state:
kobj_attr_store()
-> state_store()
-> pm_suspend()
-> suspend_devices_and_enter()
-> pseries_suspend_begin()
This never works because there is no way to supply a valid stream id
using this interface, and H_VASI_STATE is called with a stream id of
zero. So this call path is useless at best.
2. When a stream id is written to /sys/devices/system/power/hibernate.
pseries_suspend_begin() is polled directly from store_hibernate()
until the stream is in the "Suspending" state (i.e. the platform is
ready for the OS to suspend execution):
dev_attr_store()
-> store_hibernate()
-> pseries_suspend_begin()
3. When a stream id is written to /sys/devices/system/power/hibernate
(continued). After #2, pseries_suspend_begin() is called once again
from the pm core:
dev_attr_store()
-> store_hibernate()
-> pm_suspend()
-> suspend_devices_and_enter()
-> pseries_suspend_begin()
This is redundant because the VASI suspend state is already known to
be Suspending.
The begin() callback of platform_suspend_ops is optional, so we can
simply remove that assignment with no loss of function.
Fixes: 32d8ad4e62 ("powerpc/pseries: Partition hibernation support")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201207215200.1785968-18-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a9280a0d ]
Building with W=2 prints a number of warnings for one function that
has a pointer type mismatch:
linux/seq_buf.h: In function 'seq_buf_init':
linux/seq_buf.h:35:12: warning: pointer targets in assignment from 'unsigned char *' to 'char *' differ in signedness [-Wpointer-sign]
Change the type in the function prototype according to the type in
the structure.
Link: https://lkml.kernel.org/r/20201026161108.3707783-1-arnd@kernel.org
Fixes: 9a7777935c ("tracing: Convert seq_buf fields to be like seq_file fields")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0382d049d ]
This patch adds missing MODULE_ALIAS for automatic loading of this cpufreq
driver when it is compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 8def31034d ("cpufreq: arm_big_little: add SCPI interface driver")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9acab0918 ]
This patch adds missing MODULE_ALIAS for automatic loading of this cpufreq
driver when it is compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a0a22cf144 ("cpufreq: Loongson1: Add cpufreq driver for Loongson1B")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 183747ab52 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: ab0ea257fc ("cpufreq: st: Provide runtime initialised driver for ST's platforms")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af6eca0650 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 501c574f4e ("cpufreq: mediatek: Add support of cpufreq to MT2701/MT7623 SoC")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9433777a6e ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 6754f55610 ("cpufreq / highbank: add support for highbank cpufreq")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b7770b877 ]
ARM virtual counter supports event stream, it can only trigger an event
when the trigger bit (the value of CNTKCTL_EL1.EVNTI) of CNTVCT_EL0 changes,
so the actual period of event stream is 2^(cntkctl_evnti + 1). For example,
when the trigger bit is 0, then virtual counter trigger an event for every
two cycles.
While we're at it, rework the way we compute the trigger bit position
by making it more obvious that when bits [n:n-1] are both set (with n
being the most significant bit), we pick bit (n + 1).
Fixes: 037f637767 ("drivers: clocksource: add support for ARM architected timer event stream")
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201204073126.6920-3-zhukeqian1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d7659bfbe ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 2ca4c92f58 ("dm ioctl: prevent empty message")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907af0f0ca ]
mlx5 firmware expects driver version in specific format X.X.X, so
make it always correct and based on real kernel version aligned with
the driver.
Fixes: 012e50e109 ("net/mlx5: Set driver version into firmware")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dad6bed3 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e4d86e241 ]
The "a->index" value comes from the user via the ioctl. The problem is
that the shift can wrap resulting in setting "mxb->cur_audinput" to an
invalid value, which later results in an array overflow.
Fixes: 6680427791 ("[media] mxb: fix audio handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b06a56d46 ]
commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") allows drivers using mmap to put PCI memory mapped
BAR space into userspace to work correctly on AMD SME systems that default
to all memory encrypted.
Since vfio_pci_mmap_fault() is working with PCI memory mapped BAR space it
should be calling io_remap_pfn_range() otherwise it will not work on SME
systems.
Fixes: 11c4cd07ba ("vfio-pci: Fault mmaps to enable vma tracking")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Peter Xu <peterx@redhat.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf701b765e ]
nfsiod is currently a concurrency-managed workqueue (CMWQ).
This means that workitems scheduled to nfsiod on a given CPU are queued
behind all other work items queued on any CMWQ on the same CPU. This
can introduce unexpected latency.
Occaionally nfsiod can even cause excessive latency. If the work item
to complete a CLOSE request calls the final iput() on an inode, the
address_space of that inode will be dismantled. This takes time
proportional to the number of in-memory pages, which on a large host
working on large files (e.g.. 5TB), can be a large number of pages
resulting in a noticable number of seconds.
We can avoid these latency problems by switching nfsiod to WQ_UNBOUND.
This causes each concurrent work item to gets a dedicated thread which
can be scheduled to an idle CPU.
There is precedent for this as several other filesystems use WQ_UNBOUND
workqueue for handling various async events.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: ada609ee2a ("workqueue: use WQ_MEM_RECLAIM instead of WQ_RESCUER")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b82d88d59 ]
NLM uses an interval-based rebinding, i.e. it clears the transport's
binding under certain conditions if more than 60 seconds have elapsed
since the connection was last bound.
This rebinding is not necessary for an autobind RPC client over a
connection-oriented protocol like TCP.
It can also cause problems: it is possible for nlm_bind_host() to clear
XPRT_BOUND whilst a connection worker is in the middle of trying to
reconnect, after it had already been checked in xprt_connect().
When the connection worker notices that XPRT_BOUND has been cleared
under it, in xs_tcp_finish_connecting(), that results in:
xs_tcp_setup_socket: connect returned unhandled error -107
Worse, it's possible that the two can get into lockstep, resulting in
the same behaviour repeated indefinitely, with the above error every
300 seconds, without ever recovering, and the connection never being
established. This has been seen in practice, with a large number of NLM
client tasks, following a server restart.
The existing callers of nlm_bind_host & nlm_rebind_host should not need
to force the rebind, for TCP, so restrict the interval-based rebinding
to UDP only.
For TCP, we will still rebind when needed, e.g. on timeout, and connection
error (including closure), since connection-related errors on an existing
connection, ECONNREFUSED when trying to connect, and rpc_check_timeout(),
already unconditionally clear XPRT_BOUND.
To avoid having to add the fix, and explanation, to both nlm_bind_host()
and nlm_rebind_host(), remove the duplicate code from the former, and
have it call the latter.
Drop the dprintk, which adds no value over a trace.
Signed-off-by: Calum Mackay <calum.mackay@oracle.com>
Fixes: 35f5a422ce ("SUNRPC: new interface to force an RPC rebind")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5aa6b22e2 ]
According to RFC5666, the correct netid for an IPv6 addressed RDMA
transport is "rdma6", which we've supported as a mount option since
Linux-4.7. The problem is when we try to load the module "xprtrdma6",
that will fail, since there is no modulealias of that name.
Fixes: 181342c5eb ("xprtrdma: Add rdma6 option to support NFS/RDMA IPv6")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ad917561 ]
Currently, the client will always ask for security_labels if the server
returns that it supports that feature regardless of any LSM modules
(such as Selinux) enforcing security policy. This adds performance
penalty to the READDIR operation.
Client adjusts superblock's support of the security_label based on
the server's support but also current client's configuration of the
LSM modules. Thus, prior to using the default bitmask in READDIR,
this patch checks the server's capabilities and then instructs
READDIR to remove FATTR4_WORD2_SECURITY_LABEL from the bitmask.
v5: fixing silly mistakes of the rushed v4
v4: simplifying logic
v3: changing label's initialization per Ondrej's comment
v2: dropping selinux hook and using the sb cap.
Suggested-by: Ondrej Mosnacek <omosnace@redhat.com>
Suggested-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Fixes: 2b0143b5c9 ("VFS: normal filesystems (and lustre): d_inode() annotations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4615fbc378 ]
When an interrupt allocation fails for N interrupts, it is pretty
common for the error handling code to free the same number of interrupts,
no matter how many interrupts have actually been allocated.
This may result in the domain freeing code to be unexpectedly called
for interrupts that have no mapping in that domain. Things end pretty
badly.
Instead, add some checks to irq_domain_free_irqs_hierarchy() to make sure
that thiss does not follow the hierarchy if no mapping exists for a given
interrupt.
Fixes: 6a6544e520 ("genirq/irqdomain: Remove auto-recursive hierarchy support")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201129135551.396777-1-maz@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2f6cb78ea ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in callers(bq24190_sysfs_show,
bq24190_charger_get_property, bq24190_charger_set_property,
bq24190_battery_get_property, bq24190_battery_set_property),
so we should fix it.
Fixes: f385e6e2a1 ("power: bq24190_charger: Use PM runtime autosuspend")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f24479ead ]
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba877 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41fff6e19b ]
In current code, it jumps to ida_simple_remove() when ida_simple_get()
failes to allocate an ID. Just return to fix it.
Fixes: 0fae198988 ("HSI: omap_ssi: built omap_ssi and omap_ssi_port into one module")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b1b0cb063 ]
This is supposed to return negative error codes but the type is bool so
it returns true instead.
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0afe0a998c ]
Currently, lwt_len_hist's map lwt_len_hist_map is uses pinning, and the
map isn't cleared on test end. This leds to reuse of that map for
each test, which prevents the results of the test from being accurate.
This commit fixes the problem by removing of pinned map from bpffs.
Also, this commit add the executable permission to shell script
files.
Fixes: f74599f7c5 ("bpf: Add tests and samples for LWT-BPF")
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20201124090310.24374-7-danieltimlee@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abf287eeff ]
When dvb_create_media_graph fails, the debugfs kept inside client should
be released. However, the current implementation does not release them.
Fix this by adding a new goto label to call smsdvb_debugfs_release.
Fixes: 0d3ab8410d ("[media] dvb core: must check dvb_create_media_graph()")
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a31eb61564 ]
ezusb_xmit() allocates a context which is leaked if
orinoco_process_xmit_skb() returns an error.
Move ezusb_alloc_ctx() after the invocation of
orinoco_process_xmit_skb() because the context is not needed so early.
ezusb_access_ltv() will cleanup the context in case of an error.
Fixes: bac6fafd4d ("orinoco: refactor xmit path")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-2-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59bbf83835 ]
In omap4_keypad_probe, the patch fix several bugs.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) In err_unmap, forget to disable runtime of device,
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
3) In err_pm_disable, it will call pm_runtime_put_sync twice not
one time.
To fix this we factor out code reading revision and disabling touchpad, and
drop PM reference once we are done talking to the device.
Fixes: f77621cc64 ("Input: omap-keypad - dynamically handle register offsets")
Fixes: 5ad567ffba ("Input: omap4-keypad - wire up runtime PM handling")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201120133918.2559681-1-zhangqilong3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4fa73358c ]
The patch fix two reference leak.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to call put operation will result in
reference leak.
2) The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced.
We fix it by: 1) adding call pm_runtime_put_noidle or
pm_runtime_put_sync in error handling. 2) adding pm_runtime_disable
in error handling, to keep usage counter and disable depth balanced.
Fixes: 88139ed030 ("soc: ti: add Keystone Navigator DMA support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec8684847d ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in knav_queue_probe, so we should fix it.
Fixes: 41f93af900 ("soc: ti: add Keystone Navigator QMSS driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff81072003 ]
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: f7b2b5dd6a ("crypto: omap-aes - add error check for pm_runtime_get_sync")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78665179e5 ]
On 8xx, we get the following features:
[ 0.000000] cpu_features = 0x0000000000000100
[ 0.000000] possible = 0x0000000000000120
[ 0.000000] always = 0x0000000000000000
This is not correct. As CONFIG_PPC_8xx is mutually exclusive with all
other configurations, the three lines should be equal.
The problem is due to CPU_FTRS_GENERIC_32 which is taken when
CONFIG_BOOK3S_32 is NOT selected. This CPU_FTRS_GENERIC_32 is
pointless because there is no generic configuration supporting
all 32 bits but book3s/32.
Remove this pointless generic features definition to unbreak the
calculation of 'possible' features and 'always' features.
Fixes: 76bc080ef5 ("[POWERPC] Make default cputable entries reflect selected CPU family")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/76a85f30bf981d1aeaae00df99321235494da254.1604426550.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e2c9c782 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820830ec91 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e4209b380 ]
The current implementation of scsi_vpd_lun_id() uses the designator length
as an implicit measure of priority. This works most of the time, but not
always. For example, some Hitachi storage arrays return this in VPD 0x83:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: T10 vendor identification, code_set: ASCII
associated with the Addressed logical unit
vendor id: HITACHI
vendor specific: 5030C3502025
Designation descriptor number 2, descriptor length: 6
designator_type: vendor specific [0x0], code_set: Binary
associated with the Target port
vendor specific: 08 03
Designation descriptor number 3, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the Addressed logical unit
NAA 6, IEEE Company_id: 0x60e8
Vendor Specific Identifier: 0x7c35000
Vendor Specific Identifier Extension: 0x30c35000002025
[0x60060e8007c350000030c35000002025]
The current code would use the first descriptor because it's longer than
the NAA descriptor. But this is wrong, the kernel is supposed to prefer NAA
descriptors over T10 vendor ID. Designator length should only be used to
compare designators of the same type.
This patch addresses the issue by separating designator priority and
length.
Link: https://lore.kernel.org/r/20201029170846.14786-1-mwilck@suse.com
Fixes: 9983bed390 ("scsi: Add scsi_vpd_lun_id()")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27c3943683 ]
mtk_vcodec_release_dec_pm() will be called in two places:
a. mtk_vcodec_init_dec_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_dec_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_dec_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_dec_pm()
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a5fe2fb96 ]
When BCM47XX_BCMA is enabled and BCMA_DRIVER_PCI is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for BCMA_DRIVER_PCI_HOSTMODE
Depends on [n]: MIPS [=y] && BCMA_DRIVER_PCI [=n] && PCI_DRIVERS_LEGACY [=y] && BCMA [=y]=y
Selected by [y]:
- BCM47XX_BCMA [=y] && BCM47XX [=y] && PCI [=y]
The reason is that BCM47XX_BCMA selects BCMA_DRIVER_PCI_HOSTMODE without
depending on or selecting BCMA_DRIVER_PCI while BCMA_DRIVER_PCI_HOSTMODE
depends on BCMA_DRIVER_PCI. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: c1d1c5d421 ("bcm47xx: add support for bcma bus")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209879
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb7dc5db6 ]
gcc points out a suspicious mixing of enum types in a function that
converts from MTHCA_OPCODE_* values to IB_WC_* values:
drivers/infiniband/hw/mthca/mthca_cq.c: In function 'mthca_poll_one':
drivers/infiniband/hw/mthca/mthca_cq.c:607:21: warning: implicit conversion from 'enum <anonymous>' to 'enum ib_wc_opcode' [-Wenum-conversion]
607 | entry->opcode = MTHCA_OPCODE_INVALID;
Nothing seems to ever check for MTHCA_OPCODE_INVALID again, no idea if
this is meaningful, but it seems harmless as it deals with an invalid
input.
Remove MTHCA_OPCODE_INVALID and set the ib_wc_opcode to 0xFF, which is
still bogus, but at least doesn't make compiler warnings.
Fixes: 2a4443a699 ("[PATCH] IB/mthca: fill in opcode field for send completions")
Link: https://lore.kernel.org/r/20201026211311.3887003-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dfccd13db ]
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca6 ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 200ea5a229 ]
A previous fix, commit 83370b31a9 ("selinux: fix error initialization
in inode_doinit_with_dentry()"), changed how failures were handled
before a SELinux policy was loaded. Unfortunately that patch was
potentially problematic for two reasons: it set the isec->initialized
state without holding a lock, and it didn't set the inode's SELinux
label to the "default" for the particular filesystem. The later can
be a problem if/when a later attempt to revalidate the inode fails
and SELinux reverts to the existing inode label.
This patch should restore the default inode labeling that existed
before the original fix, without affecting the LABEL_INVALID marking
such that revalidation will still be attempted in the future.
Fixes: 83370b31a9 ("selinux: fix error initialization in inode_doinit_with_dentry()")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c22b80f61 ]
soc-pcm's dpcm_fe_dai_do_trigger() supported DRAIN commnad up to kernel
v5.4 where explicit switch(cmd) has been introduced which takes into
account all SNDRV_PCM_TRIGGER_xxx but SNDRV_PCM_TRIGGER_DRAIN. Update
switch statement to reactive support for it.
As DRAIN is somewhat unique by lacking negative/stop counterpart, bring
behaviour of dpcm_fe_dai_do_trigger() for said command back to its
pre-v5.4 state by adding it to START/RESUME/PAUSE_RELEASE group.
Fixes: acbf27746e ("ASoC: pcm: update FE/BE trigger order based on the command")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201026100129.8216-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0237616173 ]
current_desc_hdr() returns a u32 but in fact this is a __be32,
leading to a lot of sparse warnings.
Change the return type to __be32 and ensure it is handled as
sure by the caller.
Fixes: 3e721aeb3d ("crypto: talitos - handle descriptor not found in error path")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 345a957fcc ]
do_sched_yield() invokes schedule() with interrupts disabled which is
not allowed. This goes back to the pre git era to commit a6efb709806c
("[PATCH] irqlock patch 2.5.27-H6") in the history tree.
Reenable interrupts and remove the misleading comment which "explains" it.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/87r1pt7y5c.fsf@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a57415f5d1 ]
When change sched_rt_{runtime, period}_us, we validate that the new
settings should at least accommodate the currently allocated -dl
bandwidth:
sched_rt_handler()
--> sched_dl_bandwidth_validate()
{
new_bw = global_rt_runtime()/global_rt_period();
for_each_possible_cpu(cpu) {
dl_b = dl_bw_of(cpu);
if (new_bw < dl_b->total_bw) <-------
ret = -EBUSY;
}
}
But under CONFIG_SMP, dl_bw is per root domain , but not per CPU,
dl_b->total_bw is the allocated bandwidth of the whole root domain.
Instead, we should compare dl_b->total_bw against "cpus*new_bw",
where 'cpus' is the number of CPUs of the root domain.
Also, below annotation(in kernel/sched/sched.h) implied implementation
only appeared in SCHED_DEADLINE v2[1], then deadline scheduler kept
evolving till got merged(v9), but the annotation remains unchanged,
meaningless and misleading, update it.
* With respect to SMP, the bandwidth is given on a per-CPU basis,
* meaning that:
* - dl_bw (< 100%) is the bandwidth of the system (group) on each CPU;
* - dl_total_bw array contains, in the i-eth element, the currently
* allocated bandwidth on the i-eth CPU.
[1]: https://lore.kernel.org/lkml/1267385230.13676.101.camel@Palantir/
Fixes: 332ac17ef5 ("sched/deadline: Add bandwidth management for SCHED_DEADLINE tasks")
Signed-off-by: Peng Liu <iwtbavbm@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lkml.kernel.org/r/db6bbda316048cda7a1bbc9571defde193a8d67e.1602171061.git.iwtbavbm@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e79f0211b ]
When running in BE mode on LPAE hardware with a PA-to-VA translation
that exceeds 4 GB, we patch bits 39:32 of the offset into the wrong
byte of the opcode. So fix that, by rotating the offset in r0 to the
right by 8 bits, which will put the 8-bit immediate in bits 31:24.
Note that this will also move bit #22 in its correct place when
applying the rotation to the constant #0x400000.
Fixes: d9a790df8e ("ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE")
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fcd009102 ]
Commit
ea3b5e60ce ("x86/mm/ident_map: Add 5-level paging support")
added ident_p4d_init() to support 5-level paging, but this function
doesn't check and return errors from ident_pud_init().
For example, the decompressor stub uses this code to create an identity
mapping. If it runs out of pages while trying to allocate a PMD
pagetable, the error will be currently ignored.
Fix this to propagate errors.
[ bp: Space out statements for better readability. ]
Fixes: ea3b5e60ce ("x86/mm/ident_map: Add 5-level paging support")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lkml.kernel.org/r/20201027230648.1885111-1-nivedita@alum.mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb3ab2979f ]
The code which limited the number of unacknowledged PSNs was incorrect.
The PSNs are limited to 24 bits and wrap back to zero from 0x00ffffff.
The test was computing a 32 bit value which wraps at 32 bits so that
qp->req.psn can appear smaller than the limit when it is actually larger.
Replace '>' test with psn_compare which is used for other PSN comparisons
and correctly handles the 24 bit size.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20201013170741.3590-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83370b31a9 ]
Mark the inode security label as invalid if we cannot find
a dentry so that we will retry later rather than marking it
initialized with the unlabeled SID.
Fixes: 9287aed2ad ("selinux: Convert isec->lock into a spinlock")
Signed-off-by: Tianyue Ren <rentianyue@kylinos.cn>
[PM: minor comment tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4007844b05 ]
In the error case, where a power domain cannot be powered on
successfully at boot time (in mtk_register_power_domains),
pm_genpd_init would still be called with is_off=false, and the
system would later try to disable the power domain again, triggering
warnings as disabled clocks are disabled again (and other potential
issues).
Also print a warning splat in that case, as this should never
happen.
Fixes: c84e358718 ("soc: Mediatek: Add SCPSYS power domain driver")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20200928113107.v2.1.I5e6f8c262031d0451fe7241b744f4f3111c1ce71@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e19d51ca5 ]
clang static analysis reports this problem:
cdv_intel_dp.c:2101:2: warning: Attempt to free released memory
kfree(gma_connector);
^~~~~~~~~~~~~~~~~~~~
In cdv_intel_dp_init() when the call to cdv_intel_edp_panel_vdd_off()
fails, the handler calls cdv_intel_dp_destroy(connector) which does
the first free of gma_connector. So adjust the goto label and skip
the second free.
Fixes: d112a8163f ("gma500/cdv: Add eDP support")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003193928.18869-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92eb6c3060 upstream.
Commit 3f69cc6076 ("crypto: af_alg - Allow arbitrarily long algorithm
names") made the kernel start accepting arbitrarily long algorithm names
in sockaddr_alg. However, the actual length of the salg_name field
stayed at the original 64 bytes.
This is broken because the kernel can access indices >= 64 in salg_name,
which is undefined behavior -- even though the memory that is accessed
is still located within the sockaddr structure. It would only be
defined behavior if the array were properly marked as arbitrary-length
(either by making it a flexible array, which is the recommended way
these days, or by making it an array of length 0 or 1).
We can't simply change salg_name into a flexible array, since that would
break source compatibility with userspace programs that embed
sockaddr_alg into another struct, or (more commonly) declare a
sockaddr_alg like 'struct sockaddr_alg sa = { .salg_name = "foo" };'.
One solution would be to change salg_name into a flexible array only
when '#ifdef __KERNEL__'. However, that would keep userspace without an
easy way to actually use the longer algorithm names.
Instead, add a new structure 'sockaddr_alg_new' that has the flexible
array field, and expose it to both userspace and the kernel.
Make the kernel use it correctly in alg_bind().
This addresses the syzbot report
"UBSAN: array-index-out-of-bounds in alg_bind"
(https://syzkaller.appspot.com/bug?extid=92ead4eb8e26a26d465e).
Reported-by: syzbot+92ead4eb8e26a26d465e@syzkaller.appspotmail.com
Fixes: 3f69cc6076 ("crypto: af_alg - Allow arbitrarily long algorithm names")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f70e49ed8 upstream.
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd7e7ff56f upstream.
On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD). LDO7 also supplies
GPJ GPIO pins.
The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.
Fixes: 88644b4c75 ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-3-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d992fd8f4 upstream.
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb08965622 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a353397b0d upstream.
In many cases a function that supports SuperSpeed can very well
operate in SuperSpeedPlus, if a gadget controller supports it,
as the endpoint descriptors (and companion descriptors) are
generally identical and can be re-used. This is true for two
commonly used functions: Android's ADB and MTP. So we can simply
assign the usb_function's ssp_descriptors array to point to its
ss_descriptors, if available. Similarly, we need to allow an
epfile's ioctl for FUNCTIONFS_ENDPOINT_DESC to correctly
return the corresponding SuperSpeed endpoint descriptor in case
the connected speed is SuperSpeedPlus as well.
The only exception is if a function wants to implement an
Isochronous endpoint capable of transferring more than 48KB per
service interval when operating at greater than USB 3.1 Gen1
speed, in which case it would require an additional SuperSpeedPlus
Isochronous Endpoint Companion descriptor to be returned as part
of the Configuration Descriptor. Support for that would need
to be separately added to the userspace-facing FunctionFS API
which may not be a trivial task--likely a new descriptor format
(v3?) may need to be devised to allow for separate SS and SSP
descriptors to be supplied.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201027230731.9073-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7b624183d ]
The BUG_ON(in_interrupt()) in dm_table_event() is a historic leftover from
a rework of the dm table code which changed the calling context.
Issuing a BUG for a wrong calling context is frowned upon and
in_interrupt() is deprecated and only covering parts of the wrong
contexts. The sanity check for the context is covered by
CONFIG_DEBUG_ATOMIC_SLEEP and other debug facilities already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a35dc41fe ]
It was observed that sending data via batadv over vxlan (on top of
wireguard) reduced the performance massively compared to raw ethernet or
batadv on raw ethernet. A check of perf data showed that the
vxlan_build_skb was calling all the time pskb_expand_head to allocate
enough headroom for:
min_headroom = LL_RESERVED_SPACE(dst->dev) + dst->header_len
+ VXLAN_HLEN + iphdr_len;
But the vxlan_config_apply only requested needed headroom for:
lowerdev->hard_header_len + VXLAN6_HEADROOM or VXLAN_HEADROOM
So it completely ignored the needed_headroom of the lower device. The first
caller of net_dev_xmit could therefore never make sure that enough headroom
was allocated for the rest of the transmit path.
Cc: Annika Wickert <annika.wickert@exaring.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Annika Wickert <aw@awlnx.space>
Link: https://lore.kernel.org/r/20201126125247.1047977-1-sven@narfation.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b74e40a4e ]
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa86fc2e2 ]
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a34a0a632d upstream
drm_dp_mst_allocate_vcpi() invokes
drm_dp_mst_topology_get_port_validated(), which increases the refcount
of the "port".
These reference counting issues take place in two exception handling
paths separately. Either when “slots” is less than 0 or when
drm_dp_init_vcpi() returns a negative value, the function forgets to
reduce the refcnt increased drm_dp_mst_topology_get_port_validated(),
which results in a refcount leak.
Fix these issues by pulling up the error handling when "slots" is less
than 0, and calling drm_dp_mst_topology_put_port() before termination
when drm_dp_init_vcpi() returns a negative value.
Fixes: 1e797f556c ("drm/dp: Split drm_dp_mst_allocate_vcpi")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200719154545.GA41231@xin-virtual-machine
[sudip: use old functions before rename]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d96f04d347 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 862ee699fe upstream.
The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.
in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.
There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.
Make it depend on BROKEN for now.
Fixes: 1bbb4f2035 ("[PATCH] USB: sisusb[vga] update")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101109.603244207@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dde8ffd0 upstream.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82ca4c922b ]
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f58591323 ]
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba603d9d7b ]
In case error CQE was found while polling TX CQ, the QP is in error
state and all posted WQEs will generate error CQEs without any data
transmitted. Fix it by reopening the channels, via same method used for
TX timeout handling.
In addition add some more info on error CQE and WQE for debug.
Fixes: bd2f631d7c ("net/mlx4_en: Notify user when TX ring in error state")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fed91613c9 ]
Add restarting state flag to avoid scheduling another restart task while
such task is already running. Change task name from watchdog_task to
restart_task to better fit the task role.
Fixes: 1e338db56e ("mlx4_en: Fix a race at restart task")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 299bcb55ec ]
When cwnd is not a multiple of the TSO skb size of N*MSS, we can get
into persistent scenarios where we have the following sequence:
(1) ACK for full-sized skb of N*MSS arrives
-> tcp_write_xmit() transmit full-sized skb with N*MSS
-> move pacing release time forward
-> exit tcp_write_xmit() because pacing time is in the future
(2) TSQ callback or TCP internal pacing timer fires
-> try to transmit next skb, but TSO deferral finds remainder of
available cwnd is not big enough to trigger an immediate send
now, so we defer sending until the next ACK.
(3) repeat...
So we can get into a case where we never mark ourselves as
cwnd-limited for many seconds at a time, even with
bulk/infinite-backlog senders, because:
o In case (1) above, every time in tcp_write_xmit() we have enough
cwnd to send a full-sized skb, we are not fully using the cwnd
(because cwnd is not a multiple of the TSO skb size). So every time we
send data, we are not cwnd limited, and so in the cwnd-limited
tracking code in tcp_cwnd_validate() we mark ourselves as not
cwnd-limited.
o In case (2) above, every time in tcp_write_xmit() that we try to
transmit the "remainder" of the cwnd but defer, we set the local
variable is_cwnd_limited to true, but we do not send any packets, so
sent_pkts is zero, so we don't call the cwnd-limited logic to update
tp->is_cwnd_limited.
Fixes: ca8a226343 ("tcp: make cwnd-limited checks measurement-based, and gentler")
Reported-by: Ingemar Johansson <ingemar.s.johansson@ericsson.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201209035759.1225145-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73cc291c27 ]
If someone plays with the UFS clk scaling devfreq governor through sysfs,
ufshcd_devfreq_scale may be called even when HBA is not runtime ACTIVE.
This can lead to unexpected error. We cannot just protect it by calling
pm_runtime_get_sync() because that may cause a race condition since HBA
runtime suspend ops need to suspend clk scaling. To fix this call
pm_runtime_get_noresume() and check HBA's runtime status. Only proceed if
HBA is runtime ACTIVE, otherwise just bail.
governor_store
devfreq_performance_handler
update_devfreq
devfreq_set_target
ufshcd_devfreq_target
ufshcd_devfreq_scale
Link: https://lore.kernel.org/r/1600758548-28576-1-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e42404fa10 ]
To start stack unwinding (SP, PC and BLINK) are needed. When the
explicit execution context (pt_regs etc) is not available, unwinder
assumes the task is sleeping (in __switch_to()) and fetches SP and BLINK
from kernel mode stack.
But this assumption is not true, specially in a SMP system, when top
runs on 1 core, there may be active running processes on all cores.
So when unwinding non courrent tasks, ensure they are NOT running.
And while at it, handle the self unwinding case explicitly.
This came out of investigation of a customer reported hang with
rcutorture+top
Link: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/31
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04516706bb ]
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d853b34069 ]
Clang warns:
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc47 ("spi: bcm2835aux: Fix use-after-free on unbind")
Link: https://github.com/ClangBuiltLinux/linux/issues/1199
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
[lukas: backport to 4.19-stable, add stable designation]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.4+: e13ee6cc47: spi: bcm2835aux: Fix use-after-free on unbind
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 778721510e upstream.
If gfs2 tries to mount a (corrupt) file system that has no resource
groups it still tries to set preferences on the first one, which causes
a kernel null pointer dereference. This patch adds a check to function
gfs2_ri_update so this condition is detected and reported back as an
error.
Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcee527895 upstream.
When the instances were able to use their own options, the userstacktrace
option was left hardcoded for the top level. This made the instance
userstacktrace option bascially into a nop, and will confuse users that set
it, but nothing happens (I was confused when it happened to me!)
Cc: stable@vger.kernel.org
Fixes: 16270145ce ("tracing: Add trace options for core options to instances")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63c5395bb7 upstream
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Moreover, since commit 0392727c26 ("spi: bcm-qspi: Handle clock probe
deferral"), bcm_qspi_probe() leaks the spi_master allocation if the call
to devm_clk_get_optional() fails.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 123456789abc: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/5e31a9a59fd1c0d0b795b2fe219f25e5ee855f9d.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e844cc37a ]
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1de67a3dee upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f7 upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c75b0ff4e upstream.
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: a124692b69 ("ftrace: Enable trampoline when rec count returns back to one")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242d990c15 upstream.
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bcd9c5be upstream.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ffccbf05 upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bb ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c98fff7332 upstream.
This is a partial revert of commit 2bb70f0a4b ("USB: serial:
option: support dynamic Quectel USB compositions")
The Quectel BG96 is different from most other modern Quectel modems,
having serial functions with 3 endpoints using ff/ff/ff and ff/fe/ff
class/subclass/protocol. Including it in the change to accommodate
dynamic function mapping was incorrect.
Revert to interface number matching for the BG96, assuming static
layout of the RMNET function on interface 4. This restores support
for the serial functions on interfaces 2 and 3.
Full lsusb output for the BG96:
Bus 002 Device 003: ID 2c7c:0296
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2c7c
idProduct 0x0296
bcdDevice 0.00
iManufacturer 3 Qualcomm, Incorporated
iProduct 2 Qualcomm CDMA Technologies MSM
iSerial 4 d1098243
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 145
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 1 Qualcomm Configuration
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 254
bInterfaceProtocol 255
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Cc: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Fixes: 2bb70f0a4b ("USB: serial: option: support dynamic Quectel USB compositions")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 469aceddfa ]
Toshiaki pointed out that we now have two very similar functions to extract
the L3 protocol number in the presence of VLAN tags. And Daniel pointed out
that the unbounded parsing loop makes it possible for maliciously crafted
packets to loop through potentially hundreds of tags.
Fix both of these issues by consolidating the two parsing functions and
limiting the VLAN tag parsing to a max depth of 8 tags. As part of this,
switch over __vlan_get_protocol() to use skb_header_pointer() instead of
pskb_may_pull(), to avoid the possible side effects of the latter and keep
the skb pointer 'const' through all the parsing functions.
v2:
- Use limit of 8 tags instead of 32 (matching XMIT_RECURSION_LIMIT)
Reported-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: d7bf2ebebc ("sched: consistently handle layer3 header accesses in the presence of VLANs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 156abe2961 upstream
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[sudip: use byt_gpio and vg->pdev->dev for dev_info()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2b74419e5 upstream
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ed381439e upstream.
i40iw_mmap manipulates the vma->vm_pgoff to differentiate a push page mmap
vs a doorbell mmap, and uses it to compute the pfn in remap_pfn_range
without any validation. This is vulnerable to an mmap exploit as described
in: https://lore.kernel.org/r/20201119093523.7588-1-zhudi21@huawei.com
The push feature is disabled in the driver currently and therefore no push
mmaps are issued from user-space. The feature does not work as expected in
the x722 product.
Remove the push module parameter and all VMA attribute manipulations for
this feature in i40iw_mmap. Update i40iw_mmap to only allow DB user
mmapings at offset = 0. Check vm_pgoff for zero and if the mmaps are bound
to a single page.
Cc: <stable@kernel.org>
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Link: https://lore.kernel.org/r/20201125005616.1800-2-shiraz.saleem@intel.com
Reported-by: Di Zhu <zhudi21@huawei.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d521943f7 ]
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670fc ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b3292215 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d2bb5ad89 ]
When command interface is down, driver to reclaim all 4K page chucks that
were hold by the Firmeware. Fix a bug for 64K page size systems, where
driver repeatedly released only the first chunk of the page.
Define helper function to fill 4K chunks for a given Firmware pages.
Iterate over all unreleased Firmware pages and call the hepler per each.
Fixes: 5adff6a088 ("net/mlx5: Fix incorrect page count when in internal error")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ee50c8e26 ]
The .x25_addr[] address comes from the user and is not necessarily
NUL terminated. This leads to a couple problems. The first problem is
that the strlen() in x25_bind() can read beyond the end of the buffer.
The second problem is more subtle and could result in memory corruption.
The call tree is:
x25_connect()
--> x25_write_internal()
--> x25_addr_aton()
The .x25_addr[] buffers are copied to the "addresses" buffer from
x25_write_internal() so it will lead to stack corruption.
Verify that the strings are NUL terminated and return -EINVAL if they
are not.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: a9288525d2 ("X25: Dont let x25_bind use addresses containing characters")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/X8ZeAKm8FnFpN//B@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba246c1751 ]
TX completions received with an error return code are not
being processed properly. When an error code is seen, do not
proceed to the next completion before cleaning up the existing
entry's data structures.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b71ec95223 ]
Ensure that received Subordinate Command-Response Queue (SCRQ)
entries are properly read in order by the driver. These queues
are used in the ibmvnic device to process RX buffer and TX completion
descriptors. dma_rmb barriers have been added after checking for a
pending descriptor to ensure the correct descriptor entry is checked
and after reading the SCRQ descriptor to ensure the entire
descriptor is read before processing.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ebf179037 ]
When inet_rtm_getroute() was converted to use the RCU variants of
ip_route_input() and ip_route_output_key(), the TOS parameters
stopped being masked with IPTOS_RT_MASK before doing the route lookup.
As a result, "ip route get" can return a different route than what
would be used when sending real packets.
For example:
$ ip route add 192.0.2.11/32 dev eth0
$ ip route add unreachable 192.0.2.11/32 tos 2
$ ip route get 192.0.2.11 tos 2
RTNETLINK answers: No route to host
But, packets with TOS 2 (ECT(0) if interpreted as an ECN bit) would
actually be routed using the first route:
$ ping -c 1 -Q 2 192.0.2.11
PING 192.0.2.11 (192.0.2.11) 56(84) bytes of data.
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.173 ms
--- 192.0.2.11 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.173/0.173/0.173/0.000 ms
This patch re-applies IPTOS_RT_MASK in inet_rtm_getroute(), to
return results consistent with real route lookups.
Fixes: 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/b2d237d08317ca55926add9654a48409ac1b8f5b.1606412894.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44f64f23ba ]
Netfilter changes PACKET_OTHERHOST to PACKET_HOST before invoking the
hooks as, while it's an expected value for a bridge, routing expects
PACKET_HOST. The change is undone later on after hook traversal. This
can be seen with pairs of functions updating skb>pkt_type and then
reverting it to its original value:
For hook NF_INET_PRE_ROUTING:
setup_pre_routing / br_nf_pre_routing_finish
For hook NF_INET_FORWARD:
br_nf_forward_ip / br_nf_forward_finish
But the third case where netfilter does this, for hook
NF_INET_POST_ROUTING, the packet type is changed in br_nf_post_routing
but never reverted. A comment says:
/* We assume any code from br_dev_queue_push_xmit onwards doesn't care
* about the value of skb->pkt_type. */
But when having a tunnel (say vxlan) attached to a bridge we have the
following call trace:
br_nf_pre_routing
br_nf_pre_routing_ipv6
br_nf_pre_routing_finish
br_nf_forward_ip
br_nf_forward_finish
br_nf_post_routing <- pkt_type is updated to PACKET_HOST
br_nf_dev_queue_xmit <- but not reverted to its original value
vxlan_xmit
vxlan_xmit_one
skb_tunnel_check_pmtu <- a check on pkt_type is performed
In this specific case, this creates issues such as when an ICMPv6 PTB
should be sent back. When CONFIG_BRIDGE_NETFILTER is enabled, the PTB
isn't sent (as skb_tunnel_check_pmtu checks if pkt_type is PACKET_HOST
and returns early).
If the comment is right and no one cares about the value of
skb->pkt_type after br_dev_queue_push_xmit (which isn't true), resetting
it to its original value should be safe.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20201123174902.622102-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f33d9e2b48 ]
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55472017a4 ]
When setting congestion control via a BPF program it is seen that the
SYN/ACK for packets within a given flow will not include the ECT0 flag. A
bit of simple printk debugging shows that when this is configured without
BPF we will see the value INET_ECN_xmit value initialized in
tcp_assign_congestion_control however when we configure this via BPF the
socket is in the closed state and as such it isn't configured, and I do not
see it being initialized when we transition the socket into the listen
state. The result of this is that the ECT0 bit is configured based on
whatever the default state is for the socket.
Any easy way to reproduce this is to monitor the following with tcpdump:
tools/testing/selftests/bpf/test_progs -t bpf_tcp_ca
Without this patch the SYN/ACK will follow whatever the default is. If dctcp
all SYN/ACK packets will have the ECT0 bit set, and if it is not then ECT0
will be cleared on all SYN/ACK packets. With this patch applied the SYN/ACK
bit matches the value seen on the other packets in the given stream.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 985f733742 ]
When setting sk_err, set it to ee_errno, not ee_origin.
Commit f5f99309fa ("sock: do not set sk_err in
sock_dequeue_err_skb") disabled updating sk_err on errq dequeue,
which is correct for most error types (origins):
- sk->sk_err = err;
Commit 38b257938a ("sock: reset sk_err when the error queue is
empty") reenabled the behavior for IMCP origins, which do require it:
+ if (icmp_next)
+ sk->sk_err = SKB_EXT_ERR(skb_next)->ee.ee_origin;
But read from ee_errno.
Fixes: 38b257938a ("sock: reset sk_err when the error queue is empty")
Reported-by: Ayush Ranjan <ayushranjan@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20201126151220.2819322-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5dab0941f ]
Child sockets erroneously inherit their parent's sk_type (ie. SOCK_*),
instead of the PF_IUCV protocol that the parent was created with in
iucv_sock_create().
We're currently not using sk->sk_protocol ourselves, so this shouldn't
have much impact (except eg. getting the output in skb_dump() right).
Fixes: eac3731bd0 ("[S390]: Add AF_IUCV socket support")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20201120100657.34407-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 184eead057 upstream
Commit 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
aimed to make the USB stack more reliable by detecting and skipping
over endpoints that are duplicated between interfaces. This caused a
regression for a Hercules audio card (reported as Bugzilla #208357),
which contains such non-compliant duplications. Although the
duplications are harmless, skipping the valid endpoints prevented the
device from working.
This patch fixes the regression by adding ENDPOINT_IGNORE quirks for
the Hercules card, telling the kernel to ignore the invalid duplicate
endpoints and thereby allowing the valid endpoints to be used as
intended.
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
CC: <stable@vger.kernel.org>
Reported-by: Alexander Chalikiopoulos <bugzilla.kernel.org@mrtoasted.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170040.GA576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[sudip: use usb_endpoint_blacklist and USB_QUIRK_ENDPOINT_BLACKLIST]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7589992469 upstream.
On resource group creation via a mkdir an extra kernfs_node reference is
obtained by kernfs_get() to ensure that the rdtgroup structure remains
accessible for the rdtgroup_kn_unlock() calls where it is removed on
deletion. Currently the extra kernfs_node reference count is only
dropped by kernfs_put() in rdtgroup_kn_unlock() while the rdtgroup
structure is removed in a few other locations that lack the matching
reference drop.
In call paths of rmdir and umount, when a control group is removed,
kernfs_remove() is called to remove the whole kernfs nodes tree of the
control group (including the kernfs nodes trees of all child monitoring
groups), and then rdtgroup structure is freed by kfree(). The rdtgroup
structures of all child monitoring groups under the control group are
freed by kfree() in free_all_child_rdtgrp().
Before calling kfree() to free the rdtgroup structures, the kernfs node
of the control group itself as well as the kernfs nodes of all child
monitoring groups still take the extra references which will never be
dropped to 0 and the kernfs nodes will never be freed. It leads to
reference count leak and kernfs_node_cache memory leak.
For example, reference count leak is observed in these two cases:
(1) mount -t resctrl resctrl /sys/fs/resctrl
mkdir /sys/fs/resctrl/c1
mkdir /sys/fs/resctrl/c1/mon_groups/m1
umount /sys/fs/resctrl
(2) mkdir /sys/fs/resctrl/c1
mkdir /sys/fs/resctrl/c1/mon_groups/m1
rmdir /sys/fs/resctrl/c1
The same reference count leak issue also exists in the error exit paths
of mkdir in mkdir_rdt_prepare() and rdtgroup_mkdir_ctrl_mon().
Fix this issue by following changes to make sure the extra kernfs_node
reference on rdtgroup is dropped before freeing the rdtgroup structure.
(1) Introduce rdtgroup removal helper rdtgroup_remove() to wrap up
kernfs_put() and kfree().
(2) Call rdtgroup_remove() in rdtgroup removal path where the rdtgroup
structure is about to be freed by kfree().
(3) Call rdtgroup_remove() or kernfs_put() as appropriate in the error
exit paths of mkdir where an extra reference is taken by kernfs_get().
Backporting notes:
Since upstream commit fa7d949337 ("x86/resctrl: Rename and move rdt
files to a separate directory"), the file
arch/x86/kernel/cpu/intel_rdt_rdtgroup.c has been renamed and moved to
arch/x86/kernel/cpu/resctrl/rdtgroup.c.
Apply the change against file arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
in older stable trees.
Fixes: f3cbeacaa0 ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: e02737d5b8 ("x86/intel_rdt: Add tasks files")
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1604085088-31707-1-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd8d9db355 upstream.
Willem reported growing of kernfs_node_cache entries in slabtop when
repeatedly creating and removing resctrl subdirectories as well as when
repeatedly mounting and unmounting the resctrl filesystem.
On resource group (control as well as monitoring) creation via a mkdir
an extra kernfs_node reference is obtained to ensure that the rdtgroup
structure remains accessible for the rdtgroup_kn_unlock() calls where it
is removed on deletion. The kernfs_node reference count is dropped by
kernfs_put() in rdtgroup_kn_unlock().
With the above explaining the need for one kernfs_get()/kernfs_put()
pair in resctrl there are more places where a kernfs_node reference is
obtained without a corresponding release. The excessive amount of
reference count on kernfs nodes will never be dropped to 0 and the
kernfs nodes will never be freed in the call paths of rmdir and umount.
It leads to reference count leak and kernfs_node_cache memory leak.
Remove the superfluous kernfs_get() calls and expand the existing
comments surrounding the remaining kernfs_get()/kernfs_put() pair that
remains in use.
Superfluous kernfs_get() calls are removed from two areas:
(1) In call paths of mount and mkdir, when kernfs nodes for "info",
"mon_groups" and "mon_data" directories and sub-directories are
created, the reference count of newly created kernfs node is set to 1.
But after kernfs_create_dir() returns, superfluous kernfs_get() are
called to take an additional reference.
(2) kernfs_get() calls in rmdir call paths.
Backporting notes:
Since upstream commit fa7d949337 ("x86/resctrl: Rename and move rdt
files to a separate directory"), the file
arch/x86/kernel/cpu/intel_rdt_rdtgroup.c has been renamed and moved to
arch/x86/kernel/cpu/resctrl/rdtgroup.c.
Apply the change against file arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
for older stable trees.
Upstream commit 17eafd0762 ("x86/intel_rdt: Split resource group
removal in two") moved part of resource group removal code from
rdtgroup_rmdir_ctrl() into a separate function rdtgroup_ctrl_remove().
Apply the change against original code base of rdtgroup_rmdir_ctrl() for
older stable trees.
Fixes: 17eafd0762 ("x86/intel_rdt: Split resource group removal in two")
Fixes: 4af4a88e0c ("x86/intel_rdt/cqm: Add mount,umount support")
Fixes: f3cbeacaa0 ("x86/intel_rdt/cqm: Add rmdir support")
Fixes: d89b737901 ("x86/intel_rdt/cqm: Add mon_data")
Fixes: c7d9aac613 ("x86/intel_rdt/cqm: Add mkdir support for RDT monitoring")
Fixes: 5dc1d5c6ba ("x86/intel_rdt: Simplify info and base file lists")
Fixes: 60cf5e101f ("x86/intel_rdt: Add mkdir to resctrl file system")
Fixes: 4e978d06de ("x86/intel_rdt: Add "info" files to resctrl file system")
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1604085053-31639-1-git-send-email-xiaochen.shen@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33fc379df7 upstream.
When spectre_v2_user={seccomp,prctl},ibpb is specified on the command
line, IBPB is force-enabled and STIPB is conditionally-enabled (or not
available).
However, since
21998a3515 ("x86/speculation: Avoid force-disabling IBPB based on STIBP and enhanced IBRS.")
the spectre_v2_user_ibpb variable is set to SPECTRE_V2_USER_{PRCTL,SECCOMP}
instead of SPECTRE_V2_USER_STRICT, which is the actual behaviour.
Because the issuing of IBPB relies on the switch_mm_*_ibpb static
branches, the mitigations behave as expected.
Since
1978b3a53a ("x86/speculation: Allow IBPB to be conditionally enabled on CPUs with always-on STIBP")
this discrepency caused the misreporting of IB speculation via prctl().
On CPUs with STIBP always-on and spectre_v2_user=seccomp,ibpb,
prctl(PR_GET_SPECULATION_CTRL) would return PR_SPEC_PRCTL |
PR_SPEC_ENABLE instead of PR_SPEC_DISABLE since both IBPB and STIPB are
always on. It also allowed prctl(PR_SET_SPECULATION_CTRL) to set the IB
speculation mode, even though the flag is ignored.
Similarly, for CPUs without SMT, prctl(PR_GET_SPECULATION_CTRL) should
also return PR_SPEC_DISABLE since IBPB is always on and STIBP is not
available.
[ bp: Massage commit message. ]
Fixes: 21998a3515 ("x86/speculation: Avoid force-disabling IBPB based on STIBP and enhanced IBRS.")
Fixes: 1978b3a53a ("x86/speculation: Allow IBPB to be conditionally enabled on CPUs with always-on STIBP")
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201110123349.1.Id0cbf996d2151f4c143c90f9028651a5b49a5908@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3bc432aa8 upstream.
Commit 2f964780c0 ("USB: core: replace %p with %pK") used the %pK
format specifier for a bunch of __user pointers. But as the 'K' in
the specifier indicates, it is meant for kernel pointers. The reason
for the %pK specifier is to avoid leaks of kernel addresses, but when
the pointer is to an address in userspace the security implications
are minimal. In particular, no kernel information is leaked.
This patch changes the __user %pK specifiers (used in a bunch of
debugging output lines) to %px, which will always print the actual
address with no mangling. (Notably, there is no printk format
specifier particularly intended for __user pointers.)
Fixes: 2f964780c0 ("USB: core: replace %p with %pK")
CC: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201119170228.GB576844@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ba1cb39fc ]
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff04f3b6f2 ]
The memory leak addressed by commit fe5186cf12 is a false positive:
all allocations are recorded in a linked list, and freed when the
filesystem is unmounted. This leads to double frees, and as reported
by David, leads to crashes if SLUB is configured to self destruct when
double frees occur.
So drop the redundant kfree() again, and instead, mark the offending
pointer variable so the allocation is ignored by kmemleak.
Cc: Vamshi K Sthambamkadi <vamshi.k.sthambamkadi@gmail.com>
Fixes: fe5186cf12 ("efivarfs: fix memory leak in efivarfs_create()")
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09323b3bca ]
The ENA driver uses the readless mechanism, which uses DMA, to find
out what the DMA mask is supposed to be.
If DMA is used without setting the dma_mask first, it causes the
Intel IOMMU driver to think that ENA is a 32-bit device and therefore
disables IOMMU passthrough permanently.
This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48
before readless initialization in
ena_device_init()->ena_com_mmio_reg_read_request_init(),
which is large enough to workaround the intel_iommu issue.
DMA mask is set again to the correct value after it's received from the
device after readless is initialized.
The patch also changes the driver to use dma_set_mask_and_coherent()
function instead of the two pci_set_dma_mask() and
pci_set_consistent_dma_mask() ones. Both methods achieve the same
effect.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Mike Cui <mikecui@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8f0a86795 ]
GPIOs - as returned by of_get_named_gpio() and used by the gpiolib - are
signed integers, where negative number indicates error. The return
value of of_get_named_gpio() should not be assigned to an unsigned int
because in case of !CONFIG_GPIOLIB such number would be a valid GPIO.
Fixes: c04c674fad ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201123162351.209100-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f1251a48c ]
x86 Hyper-V used to essentially always overwrite the effective cache type
of guest memory accesses to WB. This was problematic in cases where there
is a physical device assigned to the VM, since that often requires that
the VM should have control over cache types. Thus, on newer Hyper-V since
2018, Hyper-V always honors the VM's cache type, but unexpectedly Linux VM
users start to complain that Linux VM's VRAM becomes very slow, and it
turns out that Linux VM should not map the VRAM uncacheable by ioremap().
Fix this slowness issue by using ioremap_cache().
On ARM64, ioremap_cache() is also required as the host also maps the VRAM
cacheable, otherwise VM Connect can't display properly with ioremap() or
ioremap_wc().
With this change, the VRAM on new Hyper-V is as fast as regular RAM, so
it's no longer necessary to use the hacks we added to mitigate the
slowness, i.e. we no longer need to allocate physical memory and use
it to back up the VRAM in Generation-1 VM, and we also no longer need to
allocate physical memory to back up the framebuffer in a Generation-2 VM
and copy the framebuffer to the real VRAM. A further big change will
address these for v5.11.
Fixes: 68a2d20b79 ("drivers/video: add Hyper-V Synthetic Video Frame Buffer Driver")
Tested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/20201118000305.24797-1-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e92643db51 ]
If UFS host device is in runtime-suspended state while UFS shutdown
callback is invoked, UFS device shall be resumed for register
accesses. Currently only UFS local runtime resume function will be invoked
to wake up the host. This is not enough because if someone triggers
runtime resume from block layer, then race may happen between shutdown and
runtime resume flow, and finally lead to unlocked register access.
To fix this, in ufshcd_shutdown(), use pm_runtime_get_sync() instead of
resuming UFS device by ufshcd_runtime_resume() "internally" to let runtime
PM framework manage the whole resume flow.
Link: https://lore.kernel.org/r/20201119062916.12931-1-stanley.chu@mediatek.com
Fixes: 57d104c153 ("ufs: add UFS power management support")
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14a2e551fa ]
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f36199355c ]
Maurizio found a race where the abort and cmd stop paths can race as
follows:
1. thread1 runs iscsit_release_commands_from_conn and sets
CMD_T_FABRIC_STOP.
2. thread2 runs iscsit_aborted_task and then does __iscsit_free_cmd. It
then returns from the aborted_task callout and we finish
target_handle_abort and do:
target_handle_abort -> transport_cmd_check_stop_to_fabric ->
lio_check_stop_free -> target_put_sess_cmd
The cmd is now freed.
3. thread1 now finishes iscsit_release_commands_from_conn and runs
iscsit_free_cmd while accessing a command we just released.
In __target_check_io_state we check for CMD_T_FABRIC_STOP and set the
CMD_T_ABORTED if the driver is not cleaning up the cmd because of a session
shutdown. However, iscsit_release_commands_from_conn only sets the
CMD_T_FABRIC_STOP and does not check to see if the abort path has claimed
completion ownership of the command.
This adds a check in iscsit_release_commands_from_conn so only the abort or
fabric stop path cleanup the command.
Link: https://lore.kernel.org/r/1605318378-9269-1-git-send-email-michael.christie@oracle.com
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe0a8a95e7 ]
iSCSI NOPs are sometimes "lost", mistakenly sent to the user-land iscsid
daemon instead of handled in the kernel, as they should be, resulting in a
message from the daemon like:
iscsid: Got nop in, but kernel supports nop handling.
This can occur because of the new forward- and back-locks, and the fact
that an iSCSI NOP response can occur before processing of the NOP send is
complete. This can result in "conn->ping_task" being NULL in
iscsi_nop_out_rsp(), when the pointer is actually in the process of being
set.
To work around this, we add a new state to the "ping_task" pointer. In
addition to NULL (not assigned) and a pointer (assigned), we add the state
"being set", which is signaled with an INVALID pointer (using "-1").
Link: https://lore.kernel.org/r/20201106193317.16993-1-leeman.duncan@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f0d2c876c ]
If Doorbell Buffer Config command fails even 'dev->dbbuf_dbs != NULL'
which means OACS indicates that NVME_CTRL_OACS_DBBUF_SUPP is set,
nvme_dbbuf_update_and_check_event() will check event even it's not been
successfully set.
This patch fixes mismatch among dbbuf for sq/cqs in case that dbbuf
command fails.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d4c3e76e3 ]
If this is attempted by a kthread, then return -EOPNOTSUPP as we don't
currently support that. Once we can get task_pid_ptr() doing the right
thing, then this can go away again.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7940fb035a ]
The battery status is also being reported by the logitech-hidpp driver,
so ignore the standard HID battery status to avoid reporting the same
info twice.
Note the logitech-hidpp battery driver provides more info, such as properly
differentiating between charging and discharging. Also the standard HID
battery info seems to be wrong, reporting a capacity of just 26% after
fully charging the device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65cae18882 ]
When booting a hyperthreaded system with the kernel parameter
'mitigations=auto,nosmt', the following warning occurs:
WARNING: CPU: 0 PID: 1 at drivers/xen/events/events_base.c:1112 unbind_from_irqhandler+0x4e/0x60
...
Hardware name: Xen HVM domU, BIOS 4.2.amazon 08/24/2006
...
Call Trace:
xen_uninit_lock_cpu+0x28/0x62
xen_hvm_cpu_die+0x21/0x30
takedown_cpu+0x9c/0xe0
? trace_suspend_resume+0x60/0x60
cpuhp_invoke_callback+0x9a/0x530
_cpu_up+0x11a/0x130
cpu_up+0x7e/0xc0
bringup_nonboot_cpus+0x48/0x50
smp_init+0x26/0x79
kernel_init_freeable+0xea/0x229
? rest_init+0xaa/0xaa
kernel_init+0xa/0x106
ret_from_fork+0x35/0x40
The secondary CPUs are not activated with the nosmt mitigations and only
the primary thread on each CPU core is used. In this situation,
xen_hvm_smp_prepare_cpus(), and more importantly xen_init_lock_cpu(), is
not called, so the lock_kicker_irq is not initialized for the secondary
CPUs. Let's fix this by exiting early in xen_uninit_lock_cpu() if the
irq is not set to avoid the warning from above for each secondary CPU.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20201107011119.631442-1-bmasney@redhat.com
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34a9fa2025 ]
Some HID devices don't use a report ID because they only have a single
report. In those cases, the report ID in struct hid_report will be zero
and the data for the report will start at the first byte, so don't skip
over the first byte.
Signed-off-by: Pablo Ceballos <pceballos@google.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1884583fc ]
The i8042 module exports several symbols which may be used by other
modules.
Before this commit it would refuse to load (when built as a module itself)
on systems without an i8042 controller.
This is a problem specifically for the asus-nb-wmi module. Many Asus
laptops support the Asus WMI interface. Some of them have an i8042
controller and need to use i8042_install_filter() to filter some kbd
events. Other models do not have an i8042 controller (e.g. they use an
USB attached kbd).
Before this commit the asus-nb-wmi driver could not be loaded on Asus
models without an i8042 controller, when the i8042 code was built as
a module (as Arch Linux does) because the module_init function of the
i8042 module would fail with -ENODEV and thus the i8042_install_filter
symbol could not be loaded.
This commit fixes this by exiting from module_init with a return code
of 0 if no controller is found. It also adds a i8042_present bool to
make the module_exit function a no-op in this case and also adds a
check for i8042_present to the exported i8042_command function.
The latter i8042_present check should not really be necessary because
when builtin that function can already be used on systems without
an i8042 controller, but better safe then sorry.
Reported-and-tested-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201008112628.3979-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 652f3d00de ]
The Varmilo VA104M Keyboard (04b4:07b1, reported as Varmilo Z104M)
exposes media control hotkeys as a USB HID consumer control device, but
these keys do not work in the current (5.8-rc1) kernel due to the
incorrect HID report descriptor. Fix the problem by modifying the
internal HID report descriptor.
More specifically, the keyboard report descriptor specifies the
logical boundary as 572~10754 (0x023c ~ 0x2a02) while the usage
boundary is specified as 0~10754 (0x00 ~ 0x2a02). This results in an
incorrect interpretation of input reports, causing inputs to be ignored.
By setting the Logical Minimum to zero, we align the logical boundary
with the Usage ID boundary.
Some notes:
* There seem to be multiple variants of the VA104M keyboard. This
patch specifically targets 04b4:07b1 variant.
* The device works out-of-the-box on Windows platform with the generic
consumer control device driver (hidserv.inf). This suggests that
Windows either ignores the Logical Minimum/Logical Maximum or
interprets the Usage ID assignment differently from the linux
implementation; Maybe there are other devices out there that only
works on Windows due to this problem?
Signed-off-by: Frank Yang <puilp0502@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ce1558c285 upstream
A race exists between closing a PCM and update of ELD data. In
hdmi_pcm_close(), hinfo->nid value is modified without taking
spec->pcm_lock. If this happens concurrently while processing an ELD
update in hdmi_pcm_setup_pin(), converter assignment may be done
incorrectly.
This bug was found by hitting a WARN_ON in snd_hda_spdif_ctls_assign()
in a HDMI receiver connection stress test:
[2739.684569] WARNING: CPU: 5 PID: 2090 at sound/pci/hda/patch_hdmi.c:1898 check_non_pcm_per_cvt+0x41/0x50 [snd_hda_codec_hdmi]
...
[2739.684707] Call Trace:
[2739.684720] update_eld+0x121/0x5a0 [snd_hda_codec_hdmi]
[2739.684736] hdmi_present_sense+0x21e/0x3b0 [snd_hda_codec_hdmi]
[2739.684750] check_presence_and_report+0x81/0xd0 [snd_hda_codec_hdmi]
[2739.684842] intel_audio_codec_enable+0x122/0x190 [i915]
Fixes: 42b2987079 ("ALSA: hda - hdmi playback without monitor in dynamic pcm bind mode")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201013152628.920764-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f69548ffaf upstream
Instead of calling mutex_unlock() at each error path multiple times,
take the standard goto-and-a-single-unlock approach. This will
simplify the code and make easier to find the unbalanced mutex locks.
No functional changes, but only the code readability improvement as a
preliminary work for further changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff1712f953 upstream.
With hardware dirty bit management, calling pte_wrprotect() on a writable,
dirty PTE will lose the dirty state and return a read-only, clean entry.
Move the logic from ptep_set_wrprotect() into pte_wrprotect() to ensure that
the dirty bit is preserved for writable entries, as this is required for
soft-dirty bit management if we enable it in the future.
Cc: <stable@vger.kernel.org>
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07509e10dc upstream.
pte_accessible() is used by ptep_clear_flush() to figure out whether TLB
invalidation is necessary when unmapping pages for reclaim. Although our
implementation is correct according to the architecture, returning true
only for valid, young ptes in the absence of racing page-table
modifications, this is in fact flawed due to lazy invalidation of old
ptes in ptep_clear_flush_young() where we elide the expensive DSB
instruction for completing the TLB invalidation.
Rather than penalise the aging path, adjust pte_accessible() to return
true for any valid pte, even if the access flag is cleared.
Cc: <stable@vger.kernel.org>
Fixes: 76c714be0e ("arm64: pgtable: implement pte_accessible()")
Reported-by: Yu Zhao <yuzhao@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bf9e4bd6a upstream
[BUG]
When accessing a file on a crafted image, btrfs can crash in block layer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
PGD 136501067 P4D 136501067 PUD 124519067 PMD 0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.0.0-rc8-default #252
RIP: 0010:end_bio_extent_readpage+0x144/0x700
Call Trace:
<IRQ>
blk_update_request+0x8f/0x350
blk_mq_end_request+0x1a/0x120
blk_done_softirq+0x99/0xc0
__do_softirq+0xc7/0x467
irq_exit+0xd1/0xe0
call_function_single_interrupt+0xf/0x20
</IRQ>
RIP: 0010:default_idle+0x1e/0x170
[CAUSE]
The crafted image has a tricky corruption, the INODE_ITEM has a
different type against its parent dir:
item 20 key (268 INODE_ITEM 0) itemoff 2808 itemsize 160
generation 13 transid 13 size 1048576 nbytes 1048576
block group 0 mode 121644 links 1 uid 0 gid 0 rdev 0
sequence 9 flags 0x0(none)
This mode number 0120000 means it's a symlink.
But the dir item think it's still a regular file:
item 8 key (264 DIR_INDEX 5) itemoff 3707 itemsize 32
location key (268 INODE_ITEM 0) type FILE
transid 13 data_len 0 name_len 2
name: f4
item 40 key (264 DIR_ITEM 51821248) itemoff 1573 itemsize 32
location key (268 INODE_ITEM 0) type FILE
transid 13 data_len 0 name_len 2
name: f4
For symlink, we don't set BTRFS_I(inode)->io_tree.ops and leave it
empty, as symlink is only designed to have inlined extent, all handled
by tree block read. Thus no need to trigger btrfs_submit_bio_hook() for
inline file extent.
However end_bio_extent_readpage() expects tree->ops populated, as it's
reading regular data extent. This causes NULL pointer dereference.
[FIX]
This patch fixes the problem in two ways:
- Verify inode mode against its dir item when looking up inode
So in btrfs_lookup_dentry() if we find inode mode mismatch with dir
item, we error out so that corrupted inode will not be accessed.
- Verify inode mode when getting extent mapping
Only regular file should have regular or preallocated extent.
If we found regular/preallocated file extent for symlink or
the rest, we error out before submitting the read bio.
With this fix that crafted image can be rejected gracefully:
BTRFS critical (device loop0): inode mode mismatch with dir: inode mode=0121644 btrfs type=7 dir type=1
Reported-by: Yoon Jungyeon <jungyeon@gatech.edu>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202763
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[sudip: use original btrfs_inode_type()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 005d67127f upstream
Previously, btrfs_inode_by_name() returned 0 which left caller to check
objectid of location even location if the type was invalid.
Let btrfs_inode_by_name() return -EUCLEAN if a corrupted location of a
dir entry is found. Removal of label out_err also simplifies the
function.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ drop unlikely ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b9ae0c929 upstream.
When compiling inside the kernel include linux/stddef.h instead of
stddef.h. When I compile this header file in backports for power PC I
run into a conflict with ptrdiff_t. I was unable to reproduce this in
mainline kernel. I still would like to fix this problem in the kernel.
Fixes: 6989310f5d ("wireless: Use offsetof instead of custom macro.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20200521201422.16493-1-hauke@hauke-m.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfe8cc1db0 upstream.
Alexander reported a syzkaller / KASAN finding on s390, see below for
complete output.
In do_huge_pmd_anonymous_page(), the pre-allocated pagetable will be
freed in some cases. In the case of userfaultfd_missing(), this will
happen after calling handle_userfault(), which might have released the
mmap_lock. Therefore, the following pte_free(vma->vm_mm, pgtable) will
access an unstable vma->vm_mm, which could have been freed or re-used
already.
For all architectures other than s390 this will go w/o any negative
impact, because pte_free() simply frees the page and ignores the
passed-in mm. The implementation for SPARC32 would also access
mm->page_table_lock for pte_free(), but there is no THP support in
SPARC32, so the buggy code path will not be used there.
For s390, the mm->context.pgtable_list is being used to maintain the 2K
pagetable fragments, and operating on an already freed or even re-used
mm could result in various more or less subtle bugs due to list /
pagetable corruption.
Fix this by calling pte_free() before handle_userfault(), similar to how
it is already done in __do_huge_pmd_anonymous_page() for the WRITE /
non-huge_zero_page case.
Commit 6b251fc96c ("userfaultfd: call handle_userfault() for
userfaultfd_missing() faults") actually introduced both, the
do_huge_pmd_anonymous_page() and also __do_huge_pmd_anonymous_page()
changes wrt to calling handle_userfault(), but only in the latter case
it put the pte_free() before calling handle_userfault().
BUG: KASAN: use-after-free in do_huge_pmd_anonymous_page+0xcda/0xd90 mm/huge_memory.c:744
Read of size 8 at addr 00000000962d6988 by task syz-executor.0/9334
CPU: 1 PID: 9334 Comm: syz-executor.0 Not tainted 5.10.0-rc1-syzkaller-07083-g4c9720875573 #0
Hardware name: IBM 3906 M04 701 (KVM/Linux)
Call Trace:
do_huge_pmd_anonymous_page+0xcda/0xd90 mm/huge_memory.c:744
create_huge_pmd mm/memory.c:4256 [inline]
__handle_mm_fault+0xe6e/0x1068 mm/memory.c:4480
handle_mm_fault+0x288/0x748 mm/memory.c:4607
do_exception+0x394/0xae0 arch/s390/mm/fault.c:479
do_dat_exception+0x34/0x80 arch/s390/mm/fault.c:567
pgm_check_handler+0x1da/0x22c arch/s390/kernel/entry.S:706
copy_from_user_mvcos arch/s390/lib/uaccess.c:111 [inline]
raw_copy_from_user+0x3a/0x88 arch/s390/lib/uaccess.c:174
_copy_from_user+0x48/0xa8 lib/usercopy.c:16
copy_from_user include/linux/uaccess.h:192 [inline]
__do_sys_sigaltstack kernel/signal.c:4064 [inline]
__s390x_sys_sigaltstack+0xc8/0x240 kernel/signal.c:4060
system_call+0xe0/0x28c arch/s390/kernel/entry.S:415
Allocated by task 9334:
slab_alloc_node mm/slub.c:2891 [inline]
slab_alloc mm/slub.c:2899 [inline]
kmem_cache_alloc+0x118/0x348 mm/slub.c:2904
vm_area_dup+0x9c/0x2b8 kernel/fork.c:356
__split_vma+0xba/0x560 mm/mmap.c:2742
split_vma+0xca/0x108 mm/mmap.c:2800
mlock_fixup+0x4ae/0x600 mm/mlock.c:550
apply_vma_lock_flags+0x2c6/0x398 mm/mlock.c:619
do_mlock+0x1aa/0x718 mm/mlock.c:711
__do_sys_mlock2 mm/mlock.c:738 [inline]
__s390x_sys_mlock2+0x86/0xa8 mm/mlock.c:728
system_call+0xe0/0x28c arch/s390/kernel/entry.S:415
Freed by task 9333:
slab_free mm/slub.c:3142 [inline]
kmem_cache_free+0x7c/0x4b8 mm/slub.c:3158
__vma_adjust+0x7b2/0x2508 mm/mmap.c:960
vma_merge+0x87e/0xce0 mm/mmap.c:1209
userfaultfd_release+0x412/0x6b8 fs/userfaultfd.c:868
__fput+0x22c/0x7a8 fs/file_table.c:281
task_work_run+0x200/0x320 kernel/task_work.c:151
tracehook_notify_resume include/linux/tracehook.h:188 [inline]
do_notify_resume+0x100/0x148 arch/s390/kernel/signal.c:538
system_call+0xe6/0x28c arch/s390/kernel/entry.S:416
The buggy address belongs to the object at 00000000962d6948 which belongs to the cache vm_area_struct of size 200
The buggy address is located 64 bytes inside of 200-byte region [00000000962d6948, 00000000962d6a10)
The buggy address belongs to the page: page:00000000313a09fe refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x962d6 flags: 0x3ffff00000000200(slab)
raw: 3ffff00000000200 000040000257e080 0000000c0000000c 000000008020ba00
raw: 0000000000000000 000f001e00000000 ffffffff00000001 0000000096959501
page dumped because: kasan: bad access detected
page->mem_cgroup:0000000096959501
Memory state around the buggy address:
00000000962d6880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000000962d6900: 00 fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb
>00000000962d6980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
00000000962d6a00: fb fb fc fc fc fc fc fc fc fc 00 00 00 00 00 00
00000000962d6a80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Changes for v4.14 stable:
- Make it apply w/o
* Commit 4cf5892495 ("mm: treewide: remove unused address argument
from pte_alloc functions")
* Commit 2b74030354 ("mm: Change return type int to vm_fault_t for
fault handlers")
Fixes: 6b251fc96c ("userfaultfd: call handle_userfault() for userfaultfd_missing() faults")
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org> [4.3+]
Link: https://lkml.kernel.org/r/20201110190329.11920-1-gerald.schaefer@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a371e67dc upstream.
Currently, scan_microcode() leverages microcode_matches() to check
if the microcode matches the CPU by comparing the family and model.
However, the processor stepping and flags of the microcode signature
should also be considered when saving a microcode patch for early
update.
Use find_matching_signature() in scan_microcode() and get rid of the
now-unused microcode_matches() which is a good cleanup in itself.
Complete the verification of the patch being saved for early loading in
save_microcode_patch() directly. This needs to be done there too because
save_mc_for_early() will call save_microcode_patch() too.
The second reason why this needs to be done is because the loader still
tries to support, at least hypothetically, mixed-steppings systems and
thus adds all patches to the cache that belong to the same CPU model
albeit with different steppings.
For example:
microcode: CPU: sig=0x906ec, pf=0x2, rev=0xd6
microcode: mc_saved[0]: sig=0x906e9, pf=0x2a, rev=0xd6, total size=0x19400, date = 2020-04-23
microcode: mc_saved[1]: sig=0x906ea, pf=0x22, rev=0xd6, total size=0x19000, date = 2020-04-27
microcode: mc_saved[2]: sig=0x906eb, pf=0x2, rev=0xd6, total size=0x19400, date = 2020-04-23
microcode: mc_saved[3]: sig=0x906ec, pf=0x22, rev=0xd6, total size=0x19000, date = 2020-04-27
microcode: mc_saved[4]: sig=0x906ed, pf=0x22, rev=0xd6, total size=0x19400, date = 2020-04-23
The patch which is being saved for early loading, however, can only be
the one which fits the CPU this runs on so do the signature verification
before saving.
[ bp: Do signature verification in save_microcode_patch()
and rewrite commit message. ]
Fixes: ec400ddeff ("x86/microcode_intel_early.c: Early update ucode on Intel's CPU")
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208535
Link: https://lkml.kernel.org/r/20201113015923.13960-1-yu.c.chen@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f117cb854 upstream.
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd343 ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78d732e1f3 upstream.
This file is installed by the s390 CPU Measurement sampling
facility device driver to export supported minimum and
maximum sample buffer sizes.
This file is read by lscpumf tool to display the details
of the device driver capabilities. The lscpumf tool might
be invoked by a non-root user. In this case it does not
print anything because the file contents can not be read.
Fix this by allowing read access for all users. Reading
the file contents is ok, changing the file contents is
left to the root user only.
For further reference and details see:
[1] https://github.com/ibm-s390-tools/s390-tools/issues/97
Fixes: 69f239ed33 ("s390/cpum_sf: Dynamically extend the sampling buffer if overflows occur")
Cc: <stable@vger.kernel.org> # 3.14
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fe40b8e15 upstream.
Deferring sampling attempts to the second stage has some bad interactions
with drivers that process the rate table in hardware and use the probe flag
to indicate probing packets (e.g. most mt76 drivers). On affected drivers
it can lead to probing not working at all.
If the link conditions turn worse, it might not be such a good idea to
do a lot of sampling for lower rates in this case.
Fix this by simply skipping the sample attempt instead of deferring it,
but keep the checks that would allow it to be sampled if it was skipped
too often, but only if it has less than 95% success probability.
Also ensure that IEEE80211_TX_CTL_RATE_CTRL_PROBE is set for all probing
packets.
Cc: stable@vger.kernel.org
Fixes: cccf129f82 ("mac80211: add the 'minstrel' rate control algorithm")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a860d165e upstream.
Although cache alias management calls set up and tear down TLB entries
and fast_second_level_miss is able to restore TLB entry should it be
evicted they absolutely cannot preempt each other because they use the
same TLBTEMP area for different purposes.
Disable preemption around all cache alias management calls to enforce
that.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5b1032a65 upstream.
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 KXCJ91008-s
to allow the OS to determine the angle between the display and the base
of the device, so that the OS can determine if the 2-in-1 is in laptop
or in tablet-mode.
On Windows both accelerometers are read by a special HingeAngleService
process; and this process calls a DSM (Device Specific Method) on the
ACPI KIOX010A device node for the sensor in the display, to let the
embedded-controller (EC) know about the mode so that it can disable the
kbd and touchpad to avoid spurious input while folded into tablet-mode.
This notifying of the EC is problematic because sometimes the EC comes up
thinking that device is in tablet-mode and the kbd and touchpad do not
work. This happens for example on Irbis NB111 devices after a suspend /
resume cycle (after a complete battery drain / hard reset without having
booted Windows at least once). Other 2-in-1s which are likely affected
too are e.g. the Teclast F5 and F6 series.
The kxcjk-1013 driver may seem like a strange place to deal with this,
but since it is *the* driver for the ACPI KIOX010A device, it is also
the driver which has access to the ACPI handle needed by the DSM.
Add support for calling the DSM and on probe unconditionally tell the
EC that the device is laptop mode, fixing the kbd and touchpad sometimes
not working.
Fixes: 7f6232e695 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201110133835.129080-3-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f902b21650 upstream.
The idea of the warning in ext4_update_dx_flag() is that we should warn
when we are clearing EXT4_INODE_INDEX on a filesystem with metadata
checksums enabled since after clearing the flag, checksums for internal
htree nodes will become invalid. So there's no need to warn (or actually
do anything) when EXT4_INODE_INDEX is not set.
Link: https://lore.kernel.org/r/20201118153032.17281-1-jack@suse.cz
Fixes: 48a3431195 ("ext4: fix checksum errors with indexed dirs")
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d21b96c8ed upstream.
The code change for switching to non-atomic mode brought the
unexpected mutex deadlock in get_msg(). It converted the spinlock
with the existing mutex, but there were calls with the already holding
the mutex. Since the only place that needs the extra lock is the code
path from snd_mixart_send_msg(), remove the mutex lock in get_msg()
and apply in the caller side for fixing the mutex deadlock.
Fixes: 8d3a8b5cb5 ("ALSA: mixart: Use nonatomic PCM ops")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201119121440.18945-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95a793c3bc upstream.
When processing request to add/replace user-defined element set, check
of given element identifier and decision of numeric identifier is done
in "__snd_ctl_add_replace()" helper function. When the result of check
is wrong, the helper function returns error code. The error code shall
be returned to userspace application.
Current implementation includes bug to return zero to userspace application
regardless of the result. This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: e1a7bfe380 ("ALSA: control: Fix race between adding and removing a user element")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20201113092043.16148-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d412275444 upstream.
Speakup has only one speakup_tty variable to store the tty it is managing. This
makes sense since its codebase currently assumes that there is only one user who
controls the screen reading.
That however means that we have to forbid using the line discipline several
times, otherwise the second closure would try to free a NULL ldisc_data, leading to
general protection fault: 0000 [#1] SMP KASAN PTI
RIP: 0010:spk_ttyio_ldisc_close+0x2c/0x60
Call Trace:
tty_ldisc_release+0xa2/0x340
tty_release_struct+0x17/0xd0
tty_release+0x9d9/0xcc0
__fput+0x231/0x740
task_work_run+0x12c/0x1a0
do_exit+0x9b5/0x2230
? release_task+0x1240/0x1240
? __do_page_fault+0x562/0xa30
do_group_exit+0xd5/0x2a0
__x64_sys_exit_group+0x35/0x40
do_syscall_64+0x89/0x2b0
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Cc: stable@vger.kernel.org
Reported-by: 秦世松 <qinshisong1205@gmail.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Shisong Qin <qinshisong1205@gmail.com>
Link: https://lore.kernel.org/r/20201110183541.fzgnlwhjpgqzjeth@function
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter reports a build failure on cell_defconfig and maple_defconfg:
In file included from arch/powerpc/include/asm/kup.h:10:0,
from arch/powerpc/include/asm/uaccess.h:12,
from arch/powerpc/lib/checksum_wrappers.c:24:
arch/powerpc/include/asm/book3s/64/kup-radix.h:5:1: error: data definition has no type or storage class [-Werror]
DECLARE_STATIC_KEY_FALSE(uaccess_flush_key);
^~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/include/asm/book3s/64/kup-radix.h:5:1: error: type defaults to ‘int’ in declaration of ‘DECLARE_STATIC_KEY_FALSE’ [-Werror=implicit-int]
arch/powerpc/include/asm/book3s/64/kup-radix.h:5:1: error: parameter names (without types) in function declaration [-Werror]
arch/powerpc/include/asm/book3s/64/kup-radix.h: In function ‘prevent_user_access’:
arch/powerpc/include/asm/book3s/64/kup-radix.h:18:6: error: implicit declaration of function ‘static_branch_unlikely’ [-Werror=implicit-function-declaration]
if (static_branch_unlikely(&uaccess_flush_key))
^~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/include/asm/book3s/64/kup-radix.h:18:30: error: ‘uaccess_flush_key’ undeclared (first use in this function); did you mean
‘do_uaccess_flush’?
if (static_branch_unlikely(&uaccess_flush_key))
^~~~~~~~~~~~~~~~~
do_uaccess_flush
arch/powerpc/include/asm/book3s/64/kup-radix.h:18:30: note: each undeclared identifier is reported only once for each function it appears in
cc1: all warnings being treated as errors
This is because I failed to include linux/jump_label.h in kup-radix.h. Include it.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 488dac0c92 ]
The attr->set() receive a value of u64, but simple_strtoll() is used for
doing the conversion. It will lead to the error cast if user inputs a
negative value.
Use kstrtoull() instead of simple_strtoll() to convert a string got from
the user to an unsigned value. The former will return '-EINVAL' if it
gets a negetive value, but the latter can't handle the situation
correctly. Make 'val' unsigned long long as what kstrtoull() takes,
this will eliminate the compile warning on no 64-bit architectures.
Fixes: f7b88631a8 ("fs/libfs.c: fix simple_attr_write() on 32bit machines")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/1605341356-11872-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8409071a ]
This reverts commit 6ff646b2ce.
Your maintainer committed a major braino in the rmap code by adding the
attr fork, bmbt, and unwritten extent usage bits into rmap record key
comparisons. While XFS uses the usage bits *in the rmap records* for
cross-referencing metadata in xfs_scrub and xfs_repair, it only needs
the owner and offset information to distinguish between reverse mappings
of the same physical extent into the data fork of a file at multiple
offsets. The other bits are not important for key comparisons for index
lookups, and never have been.
Eric Sandeen reports that this causes regressions in generic/299, so
undo this patch before it does more damage.
Reported-by: Eric Sandeen <sandeen@sandeen.net>
Fixes: 6ff646b2ce ("xfs: fix rmap key and record comparison functions")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ba546ebe0 ]
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efe ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac3b57adf8 ]
If the clk_register fails, we should free h before
function returns to prevent memleak.
Fixes: 474402291a ("MIPS: Alchemy: clock framework integration of onchip clocks")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd0d83eab2 ]
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a68cc0d69 ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aa9379d8f ]
In canfd_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CANFD_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: d468984688 ("can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once")
Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com
Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201103213906.24219-3-anant.thazhemadam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c958a58f ]
In can_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CAN_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: 8cb68751c1 ("can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once")
Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com
Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201103213906.24219-2-anant.thazhemadam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0e5a05cc9 ]
When execute command "perf lock report", it hits failure and outputs log
as follows:
perf: builtin-lock.c:623: report_lock_release_event: Assertion `!(seq->read_count < 0)' failed.
Aborted
This is an imbalance issue. The locking sequence structure
"lock_seq_stat" contains the reader counter and it is used to check if
the locking sequence is balance or not between acquiring and releasing.
If the tool wrongly frees "lock_seq_stat" when "read_count" isn't zero,
the "read_count" will be reset to zero when allocate a new structure at
the next time; thus it causes the wrong counting for reader and finally
results in imbalance issue.
To fix this issue, if detects "read_count" is not zero (means still have
read user in the locking sequence), goto the "end" tag to skip freeing
structure "lock_seq_stat".
Fixes: e4cef1f650 ("perf lock: Fix state machine to recognize lock sequence")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/r/20201104094229.17509-2-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33d0d84387 ]
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e1 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22843291ef ]
__sb_start_write has some weird looking lockdep code that claims to
exist to handle nested freeze locking requests from xfs. The code as
written seems broken -- if we think we hold a read lock on any of the
higher freeze levels (e.g. we hold SB_FREEZE_WRITE and are trying to
lock SB_FREEZE_PAGEFAULT), it converts a blocking lock attempt into a
trylock.
However, it's not correct to downgrade a blocking lock attempt to a
trylock unless the downgrading code or the callers are prepared to deal
with that situation. Neither __sb_start_write nor its callers handle
this at all. For example:
sb_start_pagefault ignores the return value completely, with the result
that if xfs_filemap_fault loses a race with a different thread trying to
fsfreeze, it will proceed without pagefault freeze protection (thereby
breaking locking rules) and then unlocks the pagefault freeze lock that
it doesn't own on its way out (thereby corrupting the lock state), which
leads to a system hang shortly afterwards.
Normally, this won't happen because our ownership of a read lock on a
higher freeze protection level blocks fsfreeze from grabbing a write
lock on that higher level. *However*, if lockdep is offline,
lock_is_held_type unconditionally returns 1, which means that
percpu_rwsem_is_held returns 1, which means that __sb_start_write
unconditionally converts blocking freeze lock attempts into trylocks,
even when we *don't* hold anything that would block a fsfreeze.
Apparently this all held together until 5.10-rc1, when bugs in lockdep
caused lockdep to shut itself off early in an fstests run, and once
fstests gets to the "race writes with freezer" tests, kaboom. This
might explain the long trail of vanishingly infrequent livelocks in
fstests after lockdep goes offline that I've never been able to
diagnose.
We could fix it by spinning on the trylock if wait==true, but AFAICT the
locking works fine if lockdep is not built at all (and I didn't see any
complaints running fstests overnight), so remove this snippet entirely.
NOTE: Commit f4b554af99 in 2015 created the current weird logic (which
used to exist in a different form in commit 5accdf82ba from 2012) in
__sb_start_write. XFS solved this whole problem in the late 2.6 era by
creating a variant of transactions (XFS_TRANS_NO_WRITECOUNT) that don't
grab intwrite freeze protection, thus making lockdep's solution
unnecessary. The commit claims that Dave Chinner explained that the
trylock hack + comment could be removed, but nobody ever did.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d5179458d ]
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
------------[ cut here ]------------
kernel BUG at net/core/dev.c:10254!
Internal error: Oops - BUG: 0 [#1] SMP ARM
CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46
Hardware name: Generic DT based system
PC is at netdev_run_todo+0x314/0x394
LR is at cpumask_next+0x20/0x24
pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153
sp : 855bbd58 ip : 00000001 fp : 855bbdac
r10: 80c03d00 r9 : 80c06228 r8 : 81158c54
r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280
r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002
Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85514008 DAC: 00000051
Process sh (pid: 115, stack limit = 0x7cb5703d)
...
Backtrace:
[<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c)
r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410
r4:813b9000
[<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30)
[<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8)
r5:8115b410 r4:813b9000
[<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c)
Fixes: bd466c3fb5 ("net/faraday: Support NCSI mode")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b9e2a8c99 ]
During loss recovery, retransmitted packets are forced to use TCP
timestamps to calculate the RTT samples, which have a millisecond
granularity. BBR is designed using a microsecond granularity. As a
result, multiple RTT samples could be truncated to the same RTT value
during loss recovery. This is problematic, as BBR will not enter
PROBE_RTT if the RTT sample is <= the current min_rtt sample, meaning
that if there are persistent losses, PROBE_RTT will constantly be
pushed off and potentially never re-entered. This patch makes sure
that BBR enters PROBE_RTT by checking if RTT sample is < the current
min_rtt sample, rather than <=.
The Netflix transport/TCP team discovered this bug in the Linux TCP
BBR code during lab tests.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Ryan Sharpelletti <sharpelletti@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Link: https://lore.kernel.org/r/20201116174412.1433277-1-sharpelletti.kdev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 470b747582 ]
Currently when QoS is enabled for VF and any min_rate is configured,
the driver sets bw_share value to at least 1 and doesn’t allow to set
it to 0 to make minimal rate unlimited. It means there is always a
minimal rate configured for every VF, even if user tries to remove it.
In order to make QoS disable possible, check whether all vports have
configured min_rate = 0. If this is true, set their bw_share to 0 to
disable min_rate limitations.
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 057a10fa1f ]
A call trace was found in Hangbin's Codenomicon testing with debug kernel:
[ 2615.981988] ODEBUG: free active (active state 0) object type: timer_list hint: sctp_generate_proto_unreach_event+0x0/0x3a0 [sctp]
[ 2615.995050] WARNING: CPU: 17 PID: 0 at lib/debugobjects.c:328 debug_print_object+0x199/0x2b0
[ 2616.095934] RIP: 0010:debug_print_object+0x199/0x2b0
[ 2616.191533] Call Trace:
[ 2616.194265] <IRQ>
[ 2616.202068] debug_check_no_obj_freed+0x25e/0x3f0
[ 2616.207336] slab_free_freelist_hook+0xeb/0x140
[ 2616.220971] kfree+0xd6/0x2c0
[ 2616.224293] rcu_do_batch+0x3bd/0xc70
[ 2616.243096] rcu_core+0x8b9/0xd00
[ 2616.256065] __do_softirq+0x23d/0xacd
[ 2616.260166] irq_exit+0x236/0x2a0
[ 2616.263879] smp_apic_timer_interrupt+0x18d/0x620
[ 2616.269138] apic_timer_interrupt+0xf/0x20
[ 2616.273711] </IRQ>
This is because it holds asoc when transport->proto_unreach_timer starts
and puts asoc when the timer stops, and without holding transport the
transport could be freed when the timer is still running.
So fix it by holding/putting transport instead for proto_unreach_timer
in transport, just like other timers in transport.
v1->v2:
- Also use sctp_transport_put() for the "out_unlock:" path in
sctp_generate_proto_unreach_event(), as Marcelo noticed.
Fixes: 50b5d6ad63 ("sctp: Fix a race between ICMP protocol unreachable and connect()")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ee18c179e ]
The x25_disconnect function in x25_subr.c would decrease the refcount of
"x25->neighbour" (struct x25_neigh) and reset this pointer to NULL.
However, the x25_rx_call_request function in af_x25.c, which is called
when we receive a connection request, does not increase the refcount when
it assigns the pointer.
Fix this issue by increasing the refcount of "struct x25_neigh" in
x25_rx_call_request.
This patch fixes frequent kernel crashes when using AF_X25 sockets.
Fixes: 4becb7ee5b ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect")
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201112103506.5875-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d9c8d15af ]
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded6043 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 866358ec33 ]
The current NetLabel code doesn't correctly keep track of the netlink
dump state in some cases, in particular when multiple interfaces with
large configurations are loaded. The problem manifests itself by not
reporting the full configuration to userspace, even though it is
loaded and active in the kernel. This patch fixes this by ensuring
that the dump state is properly reset when necessary inside the
netlbl_unlabel_staticlist() function.
Fixes: 8cc44579d1 ("NetLabel: Introduce static network labels for unlabeled connections")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/r/160484450633.3752.16512718263560813473.stgit@sifl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1532b97784 ]
DSA network devices rely on having their DSA management interface up and
running otherwise their ndo_open() will return -ENETDOWN. Without doing
this it would not be possible to use DSA devices as netconsole when
configured on the command line. These devices also do not utilize the
upper/lower linking so the check about the netpoll device having upper
is not going to be a problem.
The solution adopted here is identical to the one done for
net/ipv4/ipconfig.c with 728c02089a ("net: ipv4: handle DSA enabled
master network devices"), with the network namespace scope being
restricted to that of the process configuring netpoll.
Fixes: 04ff53f96a ("net: dsa: Add netconsole support")
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201117035236.22658-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92307069a9 ]
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f492eab67 ]
The driver sends Ethernet Management Datagram (EMAD) packets to the
device for configuration purposes and waits for up to 200ms for a reply.
A request is retried up to 5 times.
When the system is under heavy load, replies are not always processed in
time and EMAD transactions fail.
Make the process more robust to such delays by using exponential
backoff. First wait for up to 200ms, then retransmit and wait for up to
400ms and so on.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Reported-by: Denis Yulevich <denisyu@nvidia.com>
Tested-by: Denis Yulevich <denisyu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4260330b32 ]
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4c ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dceaa9f56 ]
The `skb' is mapped for DMA in ns_send() but does not unmap DMA in case
push_scqe() fails to submit the `skb'. The memory of the `skb' is
released so only the DMA mapping is leaking.
Unmap the DMA mapping in case push_scqe() failed.
Fixes: 864a3ff635 ("atm: [nicstar] remove virt_to_bus() and support 64-bit platforms")
Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9debfb81e7 upstream.
Clang is more aggressive about -Wformat warnings when the format flag
specifies a type smaller than the parameter. It turns out that gsi is an
int. Fixes:
drivers/acpi/evged.c:105:48: warning: format specifies type 'unsigned
char' but the argument has type 'unsigned int' [-Wformat]
trigger == ACPI_EDGE_SENSITIVE ? 'E' : 'L', gsi);
^~~
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Fixes: ea6f3af4c5 ("ACPI: GED: add support for _Exx / _Lxx handler methods")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd479e10a upstream.
When (for example) an IBSS station is pre-moved to AUTHORIZED
before it's inserted, and then the insertion fails, we don't
clean up the fast RX/TX states that might already have been
created, since we don't go through all the state transitions
again on the way down.
Do that, if it hasn't been done already, when the station is
freed. I considered only freeing the fast TX/RX state there,
but we might add more state so it's more robust to wind down
the state properly.
Note that we warn if the station was ever inserted, it should
have been properly cleaned up in that case, and the driver
will probably not like things happening out of order.
Reported-by: syzbot+2e293dbd67de2836ba42@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20201009141710.7223b322a955.I95bd08b9ad0e039c034927cce0b75beea38e059b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29daf869cb upstream.
The kernel expects pte_young() to work regardless of CONFIG_SWAP.
Make sure a minor fault is taken to set _PAGE_ACCESSED when it
is not already set, regardless of the selection of CONFIG_SWAP.
This adds at least 3 instructions to the TLB miss exception
handlers fast path. Following patch will reduce this overhead.
Also update the rotation instruction to the correct number of bits
to reflect all changes done to _PAGE_ACCESSED over time.
Fixes: d069cb4373 ("powerpc/8xx: Don't touch ACCESSED when no SWAP.")
Fixes: 5f356497c3 ("powerpc/8xx: remove unused _PAGE_WRITETHRU")
Fixes: e0a8e0d90a ("powerpc/8xx: Handle PAGE_USER via APG bits")
Fixes: 5b2753fc3e ("powerpc/8xx: Implementation of PAGE_EXEC")
Fixes: a891c43b97 ("powerpc/8xx: Prepare handlers for _PAGE_HUGE for 512k pages.")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/af834e8a0f1fa97bfae65664950f0984a70c4750.1602492856.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e50e4f0b85 upstream
If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled. This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
(free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
(release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
(really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
(driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
(__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
(bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
(driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
(do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
(kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
(kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)
Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.
The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.
Fixes: 1c4b6c3bcf ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a32a7e78b upstream.
IBM Power9 processors can speculatively operate on data in the L1 cache before
it has been completely validated, via a way-prediction mechanism. It is not possible
for an attacker to determine the contents of impermissible memory using this method,
since these systems implement a combination of hardware and software security measures
to prevent scenarios where protected data could be leaked.
However these measures don't address the scenario where an attacker induces
the operating system to speculatively execute instructions using data that the
attacker controls. This can be used for example to speculatively bypass "kernel
user access prevention" techniques, as discovered by Anthony Steinhauser of
Google's Safeside Project. This is not an attack by itself, but there is a possibility
it could be used in conjunction with side-channels or other weaknesses in the
privileged code to construct an attack.
This issue can be mitigated by flushing the L1 cache between privilege boundaries
of concern. This patch flushes the L1 cache after user accesses.
This is part of the fix for CVE-2020-4788.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d02f6b7dab upstream.
get/put_user() can be called with nontrivial arguments. fs/proc/page.c
has a good example:
if (put_user(stable_page_flags(ppage), out)) {
stable_page_flags() is quite a lot of code, including spin locks in
the page allocator.
Ensure these arguments are evaluated before user access is allowed.
This improves security by reducing code with access to userspace, but
it also fixes a PREEMPT bug with KUAP on powerpc/64s:
stable_page_flags() is currently called with AMR set to allow writes,
it ends up calling spin_unlock(), which can call preempt_schedule. But
the task switch code can not be called with AMR set (it relies on
interrupts saving the register), so this blows up.
It's fine if the code inside allow_user_access() is preemptible,
because a timer or IPI will save the AMR, but it's not okay to
explicitly cause a reschedule.
Fixes: de78a9c42a ("powerpc: Add a framework for Kernel Userspace Access Protection")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200407041245.600651-1-npiggin@gmail.com
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e3acd8c6 upstream.
The KUAP implementation adds calls in clear_user() to enable and
disable access to userspace memory. However, it doesn't add these to
__clear_user(), which is used in the ptrace regset code.
As there's only one direct user of __clear_user() (the regset code),
and the time taken to set the AMR for KUAP purposes is going to
dominate the cost of a quick access_ok(), there's not much point
having a separate path.
Rename __clear_user() to __arch_clear_user(), and make __clear_user()
just call clear_user().
Reported-by: syzbot+f25ecf4b2982d8c7a640@syzkaller-ppc64.appspotmail.com
Reported-by: Daniel Axtens <dja@axtens.net>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: de78a9c42a ("powerpc: Add a framework for Kernel Userspace Access Protection")
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
[mpe: Use __arch_clear_user() for the asm version like arm64 & nds32]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191209132221.15328-1-ajd@linux.ibm.com
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cd623333e upstream.
Today, when a function like strncpy_from_user() is called,
the userspace access protection is de-activated and re-activated
for every word read.
By implementing user_access_begin and friends, the protection
is de-activated at the beginning of the copy and re-activated at the
end.
Implement user_access_begin(), user_access_end() and
unsafe_get_user(), unsafe_put_user() and unsafe_copy_to_user()
For the time being, we keep user_access_save() and
user_access_restore() as nops.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/36d4fbf9e56a75994aca4ee2214c77b26a5a8d35.1579866752.git.christophe.leroy@c-s.fr
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Backported from commit de78a9c42a ("powerpc: Add a framework
for Kernel Userspace Access Protection"). Here we don't try to
add the KUAP framework, we just want the helper functions
because we want to put uaccess flush helpers in them.
In terms of fixes, we don't need commit 1d8f739b07 ("powerpc/kuap:
Fix set direction in allow/prevent_user_access()") as we don't have
real KUAP. Likewise as all our allows are noops and all our prevents
are just flushes, we don't need commit 9dc086f1e9 ("powerpc/futex:
Fix incorrect user access blocking") The other 2 fixes we do need.
The original description is:
This patch implements a framework for Kernel Userspace Access
Protection.
Then subarches will have the possibility to provide their own
implementation by providing setup_kuap() and
allow/prevent_user_access().
Some platforms will need to know the area accessed and whether it is
accessed from read, write or both. Therefore source, destination and
size and handed over to the two functions.
mpe: Rename to allow/prevent rather than unlock/lock, and add
read/write wrappers. Drop the 32-bit code for now until we have an
implementation for it. Add kuap to pt_regs for 64-bit as well as
32-bit. Don't split strings, use pr_crit_ratelimited().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f79643787e upstream.
IBM Power9 processors can speculatively operate on data in the L1 cache before
it has been completely validated, via a way-prediction mechanism. It is not possible
for an attacker to determine the contents of impermissible memory using this method,
since these systems implement a combination of hardware and software security measures
to prevent scenarios where protected data could be leaked.
However these measures don't address the scenario where an attacker induces
the operating system to speculatively execute instructions using data that the
attacker controls. This can be used for example to speculatively bypass "kernel
user access prevention" techniques, as discovered by Anthony Steinhauser of
Google's Safeside Project. This is not an attack by itself, but there is a possibility
it could be used in conjunction with side-channels or other weaknesses in the
privileged code to construct an attack.
This issue can be mitigated by flushing the L1 cache between privilege boundaries
of concern. This patch flushes the L1 cache on kernel entry.
This is part of the fix for CVE-2020-4788.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backport only)
We're about to grow the exception handlers, which will make a bunch of them
no longer fit within the space available. We move them out of line.
This is a fiddly and error-prone business, so in the interests of reviewability
I haven't merged this in with the addition of the entry flush.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit da2bc4644c ("powerpc/64s: Add new exception vector macros")
adds:
+#define __TRAMP_REAL_VIRT_OOL_MASKABLE(name, realvec) \
+ TRAMP_REAL_BEGIN(tramp_virt_##name); \
+ MASKABLE_RELON_EXCEPTION_PSERIES_OOL(realvec, name##_common); \
However there's no reference there or anywhere else to
MASKABLE_RELON_EXCEPTION_PSERIES_OOL and an attempt to use it
unsurprisingly doesn't work.
Add a definition provided by mpe.
Fixes: da2bc4644c ("powerpc/64s: Add new exception vector macros")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-22 10:00:23 +01:00
1609 changed files with 14112 additions and 7117 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
