As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.
To keep the compatibility, fix it by adding two macros.
Fixes: b444153fb5 ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-11-03
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
to not use page start but actual start instead to work correctly with
profiling e.g. finding hot instructions from stack traces. Also fix latter
with regards to dumping address and jited len for !multi prog, from Song.
2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:
net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'
In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: bql: better deal with GSO
While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.
On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.
This patch series :
- Add __netdev_tx_sent_queue() so that drivers
can implement efficient BQL and xmit_more support.
- Implement a work around in dev_hard_start_xmit()
for drivers not using __netdev_tx_sent_queue()
- changes mlx4 to use __netdev_tx_sent_queue()
v2: Tariq and Willem feedback addressed.
added __netdev_tx_sent_queue() (Willem suggestion)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
doorbell only depends on xmit_more and netif_tx_queue_stopped()
Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.
This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.
Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.
BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.
But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.
Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.
Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.
Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.
Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.
Code template in a driver might look like the following :
send_doorbell = __netdev_tx_sent_queue(tx_queue, nr_bytes, skb->xmit_more);
Note that __netdev_tx_sent_queue() use is not mandatory,
since following patch will change dev_hard_start_xmit()
to not care about BQL status.
But it is highly recommended so that xmit_more full benefits
can be reached (less doorbells sent, and less atomic operations as well)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-11-02
please apply one round of qeth fixes for -net.
Patch 1 is rather large and removes a use-after-free hazard from many of our
debug trace entries.
Patch 2 is yet another fix-up for the L3 subdriver's new IP address management
code.
Patch 3 and 4 resolve some fallout from the recent changes wrt how/when qeth
allocates its net_device.
Patch 5 makes sure we don't set reserved bits when building HW commands from
user-provided data.
And finally, patch 6 allows ethtool to play nice with new HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the various identifiers for 25Gbit cards, and wires them up
into sysfs and ethtool.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.
This also sets the correct command length for ARP_REMOVE_ENTRY.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e8 ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: timeout fixes for GENET and SYSTEMPORT
This patch series fixes occasional transmit timeout around the time
the system goes into suspend. GENET and SYSTEMPORT have nearly the same
logic in that regard and were both affected in the same way.
Please queue up for stable, thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network becomes (partially) unavailable, say by disabling IPv6, the
background ACK transmission routine can get itself into a tizzy by
proposing immediate ACK retransmission. Since we're in the call event
processor, that happens immediately without returning to the workqueue
manager.
The condition should clear after a while when either the network comes back
or the call times out.
Fix this by:
(1) When re-proposing an ACK on failed Tx, don't schedule it immediately.
This will allow a certain amount of time to elapse before we try
again.
(2) Enforce a return to the workqueue manager after a certain number of
iterations of the call processing loop.
(3) Add a backoff delay that increases the delay on deferred ACKs by a
jiffy per failed transmission to a limit of HZ. The backoff delay is
cleared on a successful return from kernel_sendmsg().
(4) Cancel calls immediately if the opening sendmsg fails. The layer
above can arrange retransmission or rotate to another server.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize mutex before use. Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp6_send() function is expensive on systems with a large number of
interfaces. Every time it’s called, it has to verify that the source
address does not correspond to an existing anycast address by looping
through every device and every anycast address on the device. This can
result in significant delays for a CPU when there are a large number of
neighbors and ND timers are frequently timing out and calling
neigh_invalidate().
Add anycast addresses to a global hashtable to allow quick searching for
matching anycast addresses. This is based on inet6_addr_lst in addrconf.c.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kernel-doc warning:
net/core/skbuff.c:4953: warning: Function parameter or member 'skb' not described in 'skb_gso_size_check'
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While dbecd73884 ("bpf: get kernel symbol addresses via syscall")
zeroed info.nr_jited_ksyms in bpf_prog_get_info_by_fd() for queries
from unprivileged users, commit 815581c11c ("bpf: get JITed image
lengths of functions via syscall") forgot about doing so and therefore
returns the #elems of the user set up buffer which is incorrect. It
also needs to indicate a info.nr_jited_func_lens of zero.
Fixes: 815581c11c ("bpf: get JITed image lengths of functions via syscall")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Sandipan Das <sandipan@linux.vnet.ibm.com>
Cc: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Song Liu says:
====================
Changes v1 -> v2:
1. Added main program length to bpf_prog_info->jited_fun_lens (3/3).
2. Updated commit message of 1/3 and 2/3 with more background about the
address masking, and why it is still save after the changes.
3. Replace "ulong" with "unsigned long".
This set improves bpf program address showed in /proc/kallsyms and in
bpf_prog_info. First, real program address is showed instead of page
address. Second, when there is no subprogram, bpf_prog_info->jited_ksyms
and bpf_prog_info->jited_fun_lens returns the main prog address and
length.
====================
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, when there is no subprog (prog->aux->func_cnt == 0),
bpf_prog_info does not return any jited_ksyms or jited_func_lens. This
patch adds main program address (prog->bpf_func) and main program
length (prog->jited_len) to bpf_prog_info.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, jited_ksyms in bpf_prog_info shows page addresses of jited
bpf program. The main reason here is to not expose randomized start
address. However, this is not ideal for detailed profiling (find hot
instructions from stack traces). This patch replaces the page address
with real prog start address.
This change is OK because bpf_prog_get_info_by_fd() is only available
to root.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, /proc/kallsyms shows page address of jited bpf program. The
main reason here is to not expose randomized start address. However,
This is not ideal for detailed profiling (find hot instructions from
stack traces). This patch replaces the page address with real prog start
address.
This change is OK because these addresses are still protected by sysctl
kptr_restrict (see kallsyms_show_value()), and only programs loaded by
root are added to kallsyms (see bpf_prog_kallsyms_add()).
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Most callers of pskb_trim_rcsum() simply drop the skb when
it fails, however, ip_check_defrag() still continues to pass
the skb up to stack. This is suspicious.
In ip_check_defrag(), after we learn the skb is an IP fragment,
passing the skb to callers makes no sense, because callers expect
fragments are defrag'ed on success. So, dropping the skb when we
can't defrag it is reasonable.
Note, prior to commit 88078d98d1, this is not a big problem as
checksum will be fixed up anyway. After it, the checksum is not
correct on failure.
Found this during code review.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
"I2C has a core bugfix & cleanup as well as an ID addition and
MAINTAINERS update for you"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for IMX LPI2C driver
dt-bindings: i2c: i2c-imx-lpi2c: add imx8qxp compatible string
i2c: Clear client->irq in i2c_device_remove
i2c: Remove unnecessary call to irq_find_mapping
Pull percpu fixes from Dennis Zhou:
"Two small things for v4.20.
The first fixes a clang uninitialized variable warning for arm64 in
the default path calls BUILD_BUG(). The second removes an unnecessary
unlikely() in a WARN_ON() use"
* 'for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
arm64: percpu: Initialize ret in the default case
mm: percpu: remove unnecessary unlikely()
Pull networking fixes from David Miller:
1) BPF verifier fixes from Daniel Borkmann.
2) HNS driver fixes from Huazhong Tan.
3) FDB only works for ethernet devices, reject attempts to install FDB
rules for others. From Ido Schimmel.
4) Fix spectre V1 in vhost, from Jason Wang.
5) Don't pass on-stack object to irq_set_affinity_hint() in mvpp2
driver, from Marc Zyngier.
6) Fix mlx5e checksum handling when RXFCS is enabled, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (49 commits)
openvswitch: Fix push/pop ethernet validation
net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
bpf: test make sure to run unpriv test cases in test_verifier
bpf: add various test cases to test_verifier
bpf: don't set id on after map lookup with ptr_to_map_val return
bpf: fix partial copy of map_ptr when dst is scalar
libbpf: Fix compile error in libbpf_attach_type_by_name
kselftests/bpf: use ping6 as the default ipv6 ping binary if it exists
selftests: mlxsw: qos_mc_aware: Add a test for UC awareness
selftests: mlxsw: qos_mc_aware: Tweak for min shaper
mlxsw: spectrum: Set minimum shaper on MC TCs
mlxsw: reg: QEEC: Add minimum shaper fields
net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
net: hns3: bugfix for handling mailbox while the command queue reinitialized
net: hns3: fix incorrect return value/type of some functions
net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read
net: hns3: bugfix for is_valid_csq_clean_head()
net: hns3: remove unnecessary queue reset in the hns3_uninit_all_ring()
net: hns3: bugfix for the initialization of command queue's spin lock
...
Pull sparc fixes from David Miller:
"Two small fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Wire up compat getpeername and getsockname.
sparc64: Remvoe set_fs() from perf_callchain_user().
Pull csky dtb fixups from Guo Ren:
"These fix the csky dtb Kbuild to follow the new Devicetree dtb build
rules"
* tag 'csky-for-linus-4.20-fixup-dtb' of https://github.com/c-sky/csky-linux:
csky: use common dtb build rules
csky: remove builtin-dtb Kbuild
Pull x86 platform driver updates from Darren Hart:
- Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86
as they are closely coupled with other drivers in this location.
- Improve _init* usage for acerhdf and fix some usage issues with
messages and module parameters.
- Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
- Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
- Notify intel_telemetry users when IPC1 device is not enabled.
- Update various drivers with new laptop model IDs.
- Update several intel drivers to use SPDX identifers and order headers
alphabetically.
* tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
HID: asus: only support backlight when it's not driven by WMI
platform/x86: asus-wmi: export function for evaluating WMI methods
platform/x86: asus-wmi: Only notify kbd LED hw_change by fn-key pressed
platform/x86: wmi: declare device_type structure as constant
platform/x86: ideapad: Add Y530-15ICH to no_hw_rfkill
platform/x86: Add Intel AtomISP2 dummy / power-management driver
platform/x86: touchscreen_dmi: Add min-x and min-y settings for various models
platform/x86: touchscreen_dmi: Add info for the Onda V80 Plus v3 tablet
platform/x86: touchscreen_dmi: Add info for the Trekstor Primetab T13B tablet
platform/x86: intel_telemetry: Get rid of custom macro
platform/x86: intel_telemetry: report debugfs failure
MAINTAINERS: intel_telemetry: Update maintainers info
platform/x86: Add LG Gram laptop special features driver
platform/x86: asus-wmi: Simplify the keyboard brightness updating process
platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11 convertible
platform/x86: mlx-platform: Properly use mlxplat_mlxcpld_msn201x_items
MAINTAINERS: intel_pmc_core: Update MAINTAINERS
firmware: dcdbas: include linux/io.h
platform/x86: intel-wmi-thunderbolt: Add dynamic debugging
platform/x86: intel-wmi-thunderbolt: Convert to use SPDX identifier
...
Remove the Kbuild rules in arch/csky and use common dtb build rules.
This modification is based on:
commit 37c8a5fafa ("kbuild: consolidate Devicetree dtb build rules")
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-10-31
This series contains a various collection of fixes.
Miroslav Lichvar from Red Hat or should I say IBM now? Updates the PHC
timecounter interval for igb so that it gets updated at least once
every 550 seconds.
Ngai-Mint provides a fix for fm10k to prevent a soft lockup or system
crash by adding a new condition to determine if the SM mailbox is in the
correct state before proceeding.
Jake provides several fm10k fixes, first one marks complier aborts as
non-fatal since on some platforms trigger machine check errors when the
compile aborts. Added missing device ids to the in-kernel driver. Due
to the recent fixes, bumped the driver version.
I (Jeff Kirsher) fixed a XFRM_ALGO dependency for both ixgbe and
ixgbevf. This fix was based on the original work from Arnd Bergmann,
which only fixed ixgbe.
Mitch provides a fix for i40e/avf to update the status codes, which
resolves an issue between a mis-match between i40e and the iavf driver,
which also supports the ice LAN driver.
Radoslaw fixes the ixgbe where the driver is logging a message about
spoofed packets detected when the VF is re-started with a different MAC
address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-11-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix tcp_bpf_recvmsg() to return -EAGAIN instead of 0 in non-blocking
case when no data is available yet, from John.
2) Fix a compilation error in libbpf_attach_type_by_name() when compiled
with clang 3.8, from Andrey.
3) Fix a partial copy of map pointer on scalar alu and remove id
generation for RET_PTR_TO_MAP_VALUE return types, from Daniel.
4) Add unlimited memlock limit for kernel selftest's flow_dissector_load
program, from Yonghong.
5) Fix ping for some BPF shell based kselftests where distro does not
ship "ping -6" anymore, from Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
The series contains two fixes in BPF core and test cases. For details
please see individual patches. Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Right now unprivileged tests are never executed as a BPF test run,
only loaded. Allow for running them as well so that we can check
the outcome and probe for regressions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add some more map related test cases to test_verifier kselftest
to improve test coverage. Summary: 1012 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In the verifier there is no such semantics where registers with
PTR_TO_MAP_VALUE type have an id assigned to them. This is only
used in PTR_TO_MAP_VALUE_OR_NULL and later on nullified once the
test against NULL has been pattern matched and type transformed
into PTR_TO_MAP_VALUE.
Fixes: 3e6a4b3e02 ("bpf/verifier: introduce BPF_PTR_TO_MAP_VALUE")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Roman Gushchin <guro@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ALU operations on pointers such as scalar_reg += map_value_ptr are
handled in adjust_ptr_min_max_vals(). Problem is however that map_ptr
and range in the register state share a union, so transferring state
through dst_reg->range = ptr_reg->range is just buggy as any new
map_ptr in the dst_reg is then truncated (or null) for subsequent
checks. Fix this by adding a raw member and use it for copying state
over to dst_reg.
Fixes: f1174f77b5 ("bpf/verifier: rework value tracking")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull chrome-platform updates from Benson Leung:
- Move mfd/cros_ec_lpc* includes to drivers/platform from mfd
- Adding a new interrupt path for cros_ec_lpc
* tag 'tag-chrome-platform-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: chromeos_tbmc - Remove unneeded const
platform/chrome: Add a new interrupt path for cros_ec_lpc
mfd: cros_ec: Fix and improve kerneldoc comments.
platform/chrome: Move mfd/cros_ec_lpc* includes to drivers/platform.
