* Add automatic update support for LWMON board

* Enable MSDOS/VFAT filesystem support for LWMON board

* Clear Block Lock-Bits when erasing flash on LWMON board.

* Fix return code of "fatload" command

* Disable debugging for TQM5200 board

CHANGELOG

@@ -1,7 +1,833 @@
 ======================================================================
-Changes for U-Boot 1.0.2:
+Changes since U-Boot 1.1.1:
 ======================================================================
 
+* Add automatic update support for LWMON board
+
+* Clear Block Lock-Bits when erasing flash on LWMON board.
+
+* Fix return code of "fatload" command
+
+* Enable MSDOS/VFAT filesystem support for LWMON board
+
+* Patch by Martin Krause, 03 Aug 2004:
+  change timing for SM501 graphics controller on TQM5200 module
+
+* Patch by Mark Jonas, 13 July 2004:
+  - Total5200 LCD now run in little endian mode. Endianess conversion
+    is done in hardware.
+  - Removed last reference to "console" environment variable. 
+
+* Patches by Lars Munch, 12 Jul 2004:
+  - move at45.c to board/at91rm9200dk/ since this is at91rm9200dk
+    board specific
+  - split out the LXT971A PHY from ns_9750_eth.h
+  - split the dm9161 phy part out of at91rm9200_ether.c
+
+* Patch by Andreas Engel, 12 Jul 2004:
+  Replaced hardcoded PL011 clock frequency with config variable.
+  Fixed wrong CONFIG_CMD_DFL doc.
+
+* Patch by Thomas Viehweger, 09 Jun 2004:
+  make it possible to remove chpart when there is only one partition
+
+* Add support for console over UDP (compatible to Ingo Molnar's
+  netconsole patch under Linux)
+
+* Patch by Jon Loeliger, 16 Jul 2004:
+  - support larger DDR memories up to 2G on the PC8540/8560ADS and
+    STXGP3 boards
+  - Made MPC8540/8560ADS be 33Mhz PCI by default.
+  - Removed moldy CONFIG_RAM_AS_FLASH, CFG_FLASH_PORT_WIDTH_16
+    and CONFIG_L2_INIT_RAM options.
+  - Refactor Local Bus initialization out of SDRAM setup.
+  - Re-implement new version of LBC11/DDR11 errata workarounds.
+  - Moved board specific PCI init parts out of CPU directory.
+  - Added TLB entry for PCI-1 IO Memory
+  - Updated README.mpc85xxads
+
+* Patch by Sascha Hauer, 28 Jun:
+  - add generic support for Motorola i.MX architecture
+  - add support for mx1ads, mx1fs2 and scb9328 boards
+
+* Patches by Marc Leeman, 23 Jul 2004:
+  - Add define for the PCI/Memory Buffer Configuration Register
+  - corrected comments in cpu/mpc824x/cpu_init.c
+
+* Add support for multiple serial interfaces
+  (for example to allow modem dial-in / dial-out)
+
+* Patch by Stefan Roese, 15 Jul 2004:
+  cpu/ppc4xx/sdram.c rewritten now using get_ram_size()
+
+* Fix NSCU config; add ethernet wakeup code.
+
+* Add link for preloader for Motorola Coldfire to README.m68k
+
+* Patch by Michael Bendzick, 12 Jul 2004:
+  fix output formatting in drivers/cfi_flash.c
+
+* Patch by Mark Jonas, 02 Jul 2004:
+  Fix lowboot (again) on MPC5xxx
+
+* Patch by Curt Brune, 07 Jul 2004:
+  relocate exception vectors on arm720t if needed
+
+* Patch by George G. Davis, 06 Jul 2004:
+  - update mach-types.h to latest arm.linux.org.uk master list
+  - Set correct OMAP1610 bi_arch_number for build target
+
+* Patch by Curt Brune, 06 Jul 2004:
+  evb4510: add support for timer interrupt; cleanup
+
+* Patch by Dan Poirot, 06 Jul 2004:
+  Fix sbc8260 environment variables
+
+* Cleanup redundand "console" environment variable
+
+* Patch by Mark Jonas, 05 Jul 2004:
+  add support for the Total5100's and Total5200's LCD screen
+
+* Patches by Dan Eisenhut, 01 Jul 2004:
+  - README fixes.
+  - Move doc2000.h include to prevent compiler warning on some boards
+
+* Patch by Mark Jonas, 01 Jul 2004:
+  Added support for Total5100 and Total5200 (Rev.1 and Rev.2)
+  MGT5100 and MPC5200 based Freescale platforms.
+
+* Patch by Philippe Robin, 01 Jul 2004:
+  Add initialization for Integrator and versatile board files.
+
+* Patch by Hinko Kocevar, 01 Jun 2004:
+  Fix VFD FB allocation, add LCD FB allocation on ARM
+
+* Patch by Martin Krause, 30 Jun 2004:
+  Add support for TQM5200 board
+
+* Patch by Martin Krause, 29 Jun 2004:
+  Add loopw command: infinite write loop on address range
+
+* Patches by Yasushi Shoji, 29 Jun 2004:
+  - add empty include/asm-microblaze/processor.h
+  - add to CREDITS and MAINTAINERS
+  - add gd initialization
+  - add MicroBlaze and SUZAKU board to MAKEALL script
+  - add reset support for SUZAKU
+  - add flush_cache() for MicroBlaze
+  - add CFG_FLASH_SIZE to include/configs/suzaku.h since we have fixed
+    size flash memory on SUZAKU
+
+* Patch by Prakash Kumar, 27 Jun 2004:
+  Add support for the PXA250 based Intrinsyc Cerf board.
+
+* Patch by Yasushi Shoji, 27 Jun 2004:
+  fix comment in include/common.h
+
+* Rename SBC8560 into sbc8560 for consistency
+
+* Patch by Daniel Poirot, 24 Jun 2004:
+  Add support for Wind River's sbc8240 board
+
+* Patches by Yasushi Shoji, 26 Jun 2004:
+  - drivers/serial_xuartlite.c: fix "return 0" in void function
+  - add microblaze support to mkimage tool
+
+* Patch by Fred Klatt, 25 Jun 2004:
+  Add support for WindRiver's sbc8560 board
+
+* Patch by Nicolas Lacressonniere, 24 Jun 2004
+  Small Bugs fixes for "at91rm9200dk" board:
+  - Timing modifications for SPI DataFlash access
+  - Fix NAND flash detection bug
+
+* Patch by Nicolas Lacressonniere, 24 Jun 2004:
+  Add Support for Flash AT49BV6416 for AT91RM9200DK board
+
+* Patch by Jon Loeliger, 17 June 2004:
+  Completion of the 8540ADS/8560ADS updates:
+  Fix some PCI and Rapid I/O memory maps,
+  Initialize both TSEC 1 and 2,
+  Initialize SDRAM
+  Update MAINTAINER for 85xx boards and README.mpc85xxads
+
+* Patch by Yuli Barcohen, 16 Jun 2004:
+  Remove obsolete AdderII port which was superseded by unified
+  AdderII/Adder87x port
+
+* Patch by Ladislav Michl, 16 Jun 2004:
+  Fix gcc-3.3.3 warnings for smc91111.c
+
+* Patch by Stefan Roese, 02 Jul 2004:
+  - Fix bug in 405 ethernet driver; allocated data not cleared!
+  - Fix problem in 405 i2c driver; don't try to print without console!
+
+* Patch by Paul Ruhland, 11 Jun 2004:
+  Remove debug code from 'board/lpd7a40x/flash.c'
+
+* Patch by Andrea Marson, 11 Jun 2004:
+  Update for PPChameleon board:
+  - support for SysClk @ 25MHz
+  - support for Silicon Motion SM712 VGA controller
+  - some clean ups
+
+* Patches by Richard Woodruff, 10 Jun 2004:
+  - fix problems with examples/stubs.c for GCC >= 3.4
+  - fix problems with gd initialization
+
+* Patch by Curt Brune, 17 May 2004:
+  - Add support for Samsung S3C4510B CPU (ARM7tdmi based SoC)
+  - Add support for ESPD-Inc. EVB4510 Board
+
+* Patch by Marc Leeman, 11 May 2004:
+  Fix for MPC8245 - reading PPC Memory from another device with the
+  PPC as PCI target device corrupts data due to interenal hardware
+  buffering.
+
+* Fix "cls" command when used with splash screen
+
+* Increase NFS download timeout (now 1 min - 10 sec is to short for a
+  slow download of a big image)
+
+* Add "cls" function to MPC823 LCD driver so we can reinitialize the
+  display even after showing a bitmap
+
+* Patch by Josef Wagner, 04 Jun 2004:
+  - DDR Ram support for PM520 (MPC5200)
+  - support for different flash types (PM520)
+  - USB / IDE / CF-Card / DiskOnChip support for PM520
+  - 8 bit boot rom support for PM520/CE520
+  - Add auto SDRAM module detection for MicroSys CPC45 board (MPC8245)
+  - I2C and RTC support for CPC45
+  - support of new flash type (28F160C3T) for CPC45
+
+* Fix flash parameters passed to Linux for PPChameleon board
+
+* Remove eth_init() from lib_arm/board.c; it's done in net.net.c.
+
+* Patch by Paul Ruhland, 10 Jun 2004:
+  fix support for Logic SDK-LH7A404 board and clean up the
+  LH7A404 register macros.
+
+* Patch by Matthew McClintock, 10 Jun 2004:
+  Modify code to select correct serial clock on Sandpoint8245
+
+* Patch by Robert Schwebel, 10 Jun 2004:
+  Add support for Intel K3 strata flash.
+
+* Patch by Thomas Brand, 10 Jun 2004:
+  Fix "loads" command on DK1S10 board
+
+* Patch by Yuli Barcohen, 09 Jun 2004:
+  Add support for 8MB flash SIMM and JFFS2 file system on
+  Motorola FADS board and its derivatives (MPC86xADS, MPC885ADS).
+
+* Patch by Yuli Barcohen, 09 Jun 2004:
+  Add support for Analogue&Micro Adder87x and the older AdderII board.
+
+* Patch by Ming-Len Wu, 09 Jun 2004:
+  Add suppport for MC9328 (Dargonball) CPU and Motorola MX1ADS board
+
+* Patch by Sam Song, 09 Jun 2004:
+  - Add support for RPXlite_DW board
+  - Update FLASH driver for 4*AM29DL323DB90VI
+  - Add option configuration of CFG_ENV_IS_IN_NVRAM on RPXlite_DW board
+
+* Patch by Mark Jonas, 08 June 2004:
+  - Make MPC5200 boards evaluate the SVR to print processor name and
+    version in checkcpu() (cpu/mpc5xxx/cpu.c).
+
+* Patch by Kai-Uwe Bloem, 06 May 2004:
+  Fix endianess problem in cramfs code
+
+* Patch by Tom Armistead, 04 Jun 2004:
+  Add support for MAX6900 RTC
+
+* Patches by Ladislav Michl, 03 Jun 2004:
+  - fix cfi_flash.c on LE systems
+  - let 'make mrproper' delete u-boot.img as well
+  - turn printf into debug in cfi_flash.c
+
+* Patch by Kurt Stremerch, 28 May 2004:
+  Add support for Exys XSEngine board
+
+* Patch by Martin Krause, 27 May 2004:
+  Fix a MPC5xxx I2C timing issue in i2c_probe().
+
+* Patch by Leif Lindholm, 27 May 2004:
+  Fix board_init_f() for dbau1x00 board.
+
+* Patch by Imre Deak, 26 May 2004:
+  On OMAP1610 platforms check if booting from RAM(CS0) or flash(CS3).
+  Set flash base accordingly, and decide whether to do or skip board
+  specific setup steps.
+
+* Patch by Josef Baumgartner, 26 May 2004:
+  Add missing define in include/asm-m68k/global_data.h
+
+* Patch by Josef Baumgartner, 25 May 2004:
+  Add missing functions get_ticks() and get_tbclk() in lib_m68k/time.c
+
+* Patch by Paul Ruhland, 24 May 2004:
+  fix SDRAM initialization for LPD7A400 board.
+
+* Patch by Jian Zhang, 20 May 2004:
+  add support for environment in NAND flash
+
+* Patch by Yuli Barcohen, 20 May 2004:
+  Add support for Interphase iSPAN boards.
+
+* Patches by Paul Ruhland, 17 May 2004:
+  - Add I/O functions to the smc91111 ethernet driver to support the
+    Logic LPD7A40x boards.
+  - Add support for the Logic Zoom LH7A40x based SDK board(s),
+    specifically the LPD7A400.
+
+* Patches by Robert Schwebel, 15 May 2004:
+  - call MAC address reading code also for SMSC91C111;
+  - make SMSC91C111 timeout configurable, remove duplicate code
+  - fix get_timer() for PXA
+  - update doc/README.JFFS2
+  - use "bootfile" env variable also for jffs2
+
+* Patch by Tolunay Orkun, 14 May 2004:
+  Add support for Cogent CSB472 board (8MB Flash Rev)
+
+* Patch by Thomas Viehweger, 14 May 2004:
+  - flash.h: more flash types added
+  - immap_8260.h: some bits added (useful for RMII)
+  - cmd_coninfo.c: typo corrected, printf -> puts
+  - reduced size by replacing spaces with tab
+
+* Patch by Robert Schwebel, 13 May 2004:
+  Add 'imgextract' command: extract one part of a multi file image.
+
+* Patches by Jon Loeliger, 11 May 2004:
+  Dynamically handle REV1 and REV2 MPC85xx parts.
+    (Jon Loeliger, 10-May-2004).
+  New consistent memory map and Local Access Window across MPC85xx line.
+  New CCSRBAR at 0xE000_0000 now.
+  Add RAPID I/O memory map.
+  New memory map in README.MPC85xxads
+    (Kumar Gala, 10-May-2004)
+  Better board and CPU identification on MPC85xx boards at boot.
+    (Jon Loeliger, 10-May-2004)
+  SDRAM clock control fixes on MPC8540ADS & MPC8560 boards.
+  Some configuration options for MPC8540ADS & MPC8560ADS cleaned up.
+    (Jim Robertson, 10-May-2004)
+  Rewrite of the MPC85xx Three Speed Ethernet Controller (TSEC) driver.
+  Supports multiple PHYs.
+    (Andy Fleming, 10-May-2004)
+  Some README.MPC85xxads updates.
+    (Kumar Gala, 10-May-2004)
+  Copyright updates for "Freescale"
+    (Andy Fleming, 10-May-2004)
+
+* Patch by Stephen Williams, 11 May 2004:
+  Add flash support for ST M29W040B
+  Reduce JSE specific flash.c to remove dead code.
+
+* Patch by Markus Pietrek, 04 May 2004:
+  Fix clear_bss code for ARM systems (all except s3c44b0 which
+  doesn't clear BSS at all?)
+
+* Fix "ping" problem on INC-IP board. Strange problem:
+  Sometimes the store word instruction hangs while writing to one of
+  the Switch registers, but only if the next instruction is 16-byte
+  aligned. Moving the instruction into a separate function somehow
+  makes the problem go away.
+
+* Patch by Rishi Bhattacharya, 08 May 2004:
+  Add support for TI OMAP5912 OSK Board
+
+* Patch by Sam Song May, 07 May 2004:
+  Fix typo of UPM table for rmu board
+
+* Patch by Pantelis Antoniou, 05 May 2004:
+  - Intracom board update.
+  - Add Codec POST.
+
+* Add support for the second Ethernet interface for the 'PPChameleon'
+  board.
+
+* Patch by Dave Peverley, 30 Apr 2004:
+  Add support for OMAP730 Perseus2 Development board
+
+* Patch by Alan J. Luse, 29 Apr 2004:
+  Fix flash chip-select (OR0) option register setting on FADS boards.
+
+* Patch by Alan J. Luse, 29 Apr 2004:
+  Report MII network speed and duplex setting properly when
+  auto-negotiate is not enabled.
+
+* Patch by Jarrett Redd, 29 Apr 2004:
+  Fix hang on reset on Ocotea board due to flash in wrong mode.
+
+* Patch by Dave Peverley, 29 Apr 2004:
+  add MAC address detection to smc91111 driver
+
+* Patch by David M<>ller, 28 Apr 2004:
+  fix typo in lib_arm/board.c
+
+* Patch by Tolunay Orkun, 20 Apr 2004:
+  - README update: add CONFIG_CSB272 and csb272_config
+  - add descriptions for some MII/PHY options, CONFIG_I2CFAST, and
+    i2cfast environment variable
+
+* Patch by Yuli Barcohen, 19 Apr 2004:
+  - Rename DUET_ADS to MPC885ADS
+  - Rename CONFIG_DUET to CONFIG_MPC885_FAMILY
+  - Rename CONFIG_866_et_al to CONFIG_MPC866_FAMILY
+  - Clean up FADS family port to use the new defines
+
+* Fix PCI support on CPC45 board
+
+* Patch by Scott McNutt, 25 Apr 2004:
+  Add Nios GDB/JTAG Console support:
+  - Add stubs to support gdb via JTAG.
+  - Add support for console over JTAG.
+  - Minor cleanup.
+
+* Add support for CATcenter board (based on PPChameleon ME module)
+
+* Patch by Klaus Heydeck, 12 May 2004:
+  Using external watchdog for KUP4 boards in mpc8xx/cpu.c;
+  load_sernum_ethaddr() for KUP4 boards in lib_ppc/board.c;
+  various changes to KUP4 board specific files
+
+* Fix minor network problem on MPC5200: need some delay between
+  resetting the PHY and sending the first packet. Implemented in a
+  "natural" way by invoking the PHY reset and initialization code
+  only once after power on vs. each time the interface is brought up.
+
+* Add some limited support for low-speed devices to SL811 USB controller
+  (at least "usb reset" now passes successfully and "usb info" displays
+  correct information)
+
+* Change init sequence for multiple network interfaces: initialize
+  on-chip interfaces before external cards.
+
+* Fix memory leak in the NAND-specific JFFS2 code
+
+* Fix SL811 USB controller when attached to a USB hub
+
+* Fix config option spelling in PM520 config file
+
+* Fix PHY discovery problem in cpu/mpc8xx/fec.c (introduced by
+  patches by Pantelis Antoniou, 30 Mar 2004)
+
+* Fix minor NAND JFFS2 related issue
+
+* Fixes for SL811 USB controller:
+  - implement workaround for broken memory stick
+  - improve error handling
+
+* Increase packet send timeout to 1 ms in cpu/mpc8xx/scc.c to better
+  cope with congested networks.
+
+======================================================================
+Changes for U-Boot 1.1.1:
+======================================================================
+
+* Patch by Travis Sawyer, 23 Apr 2004:
+  Fix VSC/CIS 8201 phy descrambler interoperability timing due to
+  errata from Vitesse Semiconductor.
+
+* Patch by Philippe Robin, 22 Apr 2004:
+  Fix ethernet configuration for "versatile" board
+
+* Patch by Kshitij Gupta, 21 Apr 2004:
+  Remove busy loop and use MPU timer fr usleep() on OMAP1510/1610 boards
+
+* Patch by Steven Scholz, 24 Feb 2004:
+  Fix a bug in AT91RM9200 ethernet driver:
+  The MII interface is now initialized before accessing the PHY.
+
+* Patch by John Kerl, 19 Apr 2004:
+  Use U-boot's miiphy.h for PHY register names, rather than
+  introducing a new header file.
+
+* Update pci_ids.h from linux-2.4.26
+
+* Patch by Masami Komiya, 19 Apr 2004:
+  Fix problem cause by VLAN function on little endian architecture
+  without VLAN environment
+
+* Clean up the TQM8xx_YYMHz configurations; allow to use the same
+  binary image for all clock frequencies. Implement run-time
+  optimization of flash access timing based on the actual bus
+  frequency.
+
+* Modify KUP4X board configuration to use SL811 driver for USB memory
+  sticks (including FAT / VFAT filesystem support)
+
+* Add SL811 Host Controller Interface driver for USB
+
+* Add CFG_I2C_EEPROM_ADDR_OVERFLOW desription to README
+
+* Patch by Pantelis Antoniou, 19 Apr 2004:
+  Allow to use shell style syntax (i. e. ${var} ) with standard parser.
+  Minor patches for Intracom boards.
+
+* Patch by Christian Pell, 19 Apr 2004:
+  cleanup support for CF/IDE on PCMCIA for PXA25X
+
+* Temporarily disabled John Kerl's extended MII command code because
+  "miivals.h" is missing
+
+* Patches by Mark Jonas, 13 Apr 2004:
+  - Remove CS0 chip select timing setting from cpu/mpc5xxx/start.S
+  - Add sync instructions to IceCube SDRAM init code
+  - Move SDRAM chip constants into seperate include files
+  - Unify DDR and SDR initialization code
+  - Unify all IceCube (Lite5xxx) target names
+
+* Patch by John Kerl, 16 Apr 2004:
+  Enable ranges in mii command, e.g. mii read 0-1f 0 or
+  mii read 4-7 18-1a.  Also add mii dump subcommand for
+  pretty-printing standard regs 0-5.
+
+* Patch by  Stephen Williams, 16 April 2004:
+  fix typo in JSE.h; update MAINTAINERS
+
+* Patch by Matthew S. McClintock, 14 Apr 2004:
+  fix initdram function for utx8245 board
+
+* Patch by Markus Pietrek, 14 Apr 2004:
+  use ATAG_INITRD2 instead of deprecated ATAG_INITRD tag
+
+* Patch by Reinhard Meyer, 18 Apr 2004:
+  provide the IDE Reset Function for EMK 5200 boards
+
+* Patch by Masami Komiya, 12 Apr 2004:
+  fix pci_hose_write_config_{byte,word}_via_dword problems
+
+* Patch by Sangmoon Kim, 12 Apr 2004:
+  Update max RAM size for debris board
+
+* Patch by Travis Sawyer, 08 Apr 2004:
+  Add TLB entry for second DIMM slot on ocotea
+
+* Patch by Masami Komiya, 08 Apr 2004:
+  add RTL8169 network driver
+
+* Patch by Dan Malek, 07 Apr 2004:
+  - Add support for RPC/STx GP3, Motorola 8560 board
+  - Update 85xx TSEC driver so it searches MII for first available PHY
+    and uses that one.
+  - Add functions to support console MII commands.
+
+* Patch by Tolunay Orkun, 07 Apr 2004:
+  Move initialization of bi_iic_fast[]
+  from board_init_f() to board_init_r()
+
+* Patch by Yasushi Shoji, 07 Apr 2004:
+  Cleanup microblaze port
+
+* Patch by Sangmoon Kim, 07 Apr 2004:
+  Add auto SDRAM module detection for Debris board
+
+* Patch by Rune Torgersen, 06 Apr 2004:
+  - Fix some PCI problems on the MPC8266ADS board
+  - Fix the location of some PCI entries in the immap structure
+
+* Patch by Yasushi Shoji, 07 Apr 2004:
+  - add support for microblaze processors
+  - add support for AtmarkTechno "suzaku" board
+
+* Configure PPChameleon board to use redundand environment in flash
+
+* Configure PPChameleon board to use JFFS2 NAND support.
+
+* Added support for JFFS2 filesystem (read-only) on top of NAND flash
+
+* Patch by Rune Torgersen, 16 Apr 2004:
+  LBA48 fixes
+
+* Patches by Pantelis Antoniou, 16 Apr 2004:
+  - add support for a new version of an Intracom board and fix
+    various other things on others.
+  - add verify support to the crc32 command (define
+    CONFIG_CRC32_VERIFY to enable it)
+  - fix FEC driver for MPC8xx systems:
+    1. fix compilation problems for boards that use dynamic
+       allocation of DPRAM
+    2. shut down FEC after network transfers
+  - HUSH parser fixes:
+    1. A new test command was added. This is a simplified version of
+       the one in the bourne shell.
+    2. A new exit command was added which terminates the current
+       executing script.
+    3. Fixed handing of $? (exit code of last executed command)
+  - Fix some compile problems;
+    add "once" functionality for the netretry variable
+
+* Patch by George G. Davis, 02 Apr 2004:
+  add support for Intel Assabet board
+
+* Patch by Stephen Williams, 01 Apr 2004:
+  Add support for Picture Elements JSE board
+
+* Patch by Christian Pell, 01 Apr 2004:
+  Add CompactFlash support for PXA systems.
+
+* Patches by Pantelis Antoniou, 30 Mar 2004:
+  - add auto-complete support to the U-Boot CLI
+  - add support for NETTA and NETPHONE boards; fix NETVIA board
+  - add support for the Epson 156x series of graphical displays
+    (These displays are serial and not suitable for using a normal
+    framebuffer console on them)
+  - add infrastructure needed in order to POST any DSPs in a board
+  - improve and fix various things in the MPC8xx FEC driver:
+    1. The new 87x and 88x series of processors have two FECs,
+       and the new driver supports them both.
+    2. Another change in the 87x/88x series is support for
+       the RMII (Reduced MII) interface. However numerous
+       changes are needed to make it work since the PHYs
+       are connected to the same lines. That means that
+       you have to address them correctly over the MII
+       interface.
+    3. We now correctly match the MII/RMII interface
+       configuration to what the PHY reports.
+  - Fix problem when readingthe MII status register. Due to the
+    internal design of many PHYs you have to read the register
+    twice. The problem is more apparent in 10Mbit mode.
+  - add new mode ".jffs2s" for reading from a NAND device: it just
+    skips over bad blocks.
+  - add networking support for VLANs (802.1q), and CDP (Cisco
+    Discovery Protocol)
+  - some minor patches / cleanup
+
+* Patch by Yuli Barcohen, 28 Mar 2004:
+  - Add support for MPC8272 family including MPC8247/8248/8271/8272
+  - Add support for MPC8272ADS evaluation board (another flavour of MPC8260ADS)
+  - Change configuration method for MPC8260ADS family
+
+* add startup code to clear the BSS of standalone applications
+
+* Fix if / elif handling bug in HUSH shell
+
+======================================================================
+Changes for U-Boot 1.1.0:
+======================================================================
+
+* Patch by Mark Jonas: Remove config.tmp files only when
+  unconfiguring the board
+
+* Adapt RMU board for bigger flash memory
+
+* Patch by Klaus Heydeck, 13 Mar 2003:
+  Add support for KUP4X Board
+
+* Patch by Pavel Bartusek, 21 Mar 2004
+  Add Reiserfs support
+
+* Patch by Hinko Kocevar, 20 Mar 2004
+  - Add auto-release for SMSC LAN91c111 driver
+  - Add save/restore of PTR and PNR regs as suggested in datasheet
+
+* Patch by Stephen Williams, 19 March 2004
+  Increase speed of sector reads from SystemACE,
+  shorten poll timeout and remove a useless reset
+
+* Patch by Tolunay Orkun, 19 Mar 2004:
+  Make GigE PHY 1000Mbps Speed/Duplex detection conditional
+  (CONFIG_PHY_GIGE)
+
+* Patch by Brad Kemp, 18 Mar 2004:
+  prevent machine checks during a PCI scan
+
+* Patch by Pierre Aubert, 18 Mar 2004:
+  Fix string cleaning in IDE identification
+
+* Patch by Pierre Aubert, 18 Mar 2004:
+  - Unify video mode handling for Chips & Technologies 69000 Video
+    chip and Silicon Motion SMI 712/710/810 Video chip
+  - Add selection of the video output (CRT or LCD) via 'videoout'
+    environment variable for the Silicon Motion
+  - README update
+
+* Patch by Pierre Aubert, 18 Mar 2004:
+  include/common.h typo fix
+
+* Patches by Tolunay Orkun, 17 Mar 2004:
+  - Add support for bd->bi_iic_fast[] initialization via environment
+    variable "i2cfast" (CONFIG_I2CFAST)
+  - Add "i2cfast" u-boot environment variable support for csb272
+
+* Patch by Carl Riechers, 17 Mar 2004:
+  Ignore '\0' characters in console input for use with telnet and
+  telco pads.
+
+* Patch by Leon Kukovec, 17 Mar 2004:
+  typo fix for strswab prototype #ifdef
+
+* Patches by Thomas Viehweger, 16 Mar 2004:
+  - show PCI clock frequency on MPC8260 systems
+  - add FCC_PSMR_RMII flag for HiP7 processors
+  - in do_jffs2_fsload(), take load address from load_addr if not set
+    explicit, update load_addr otherwise
+  - replaced printf by putc/puts when no formatting is needed
+    (smaller code size, faster execution)
+
+* Patch by Phillippe Robin, 16 Mar 2004:
+  avoid dereferencing NULL pointer in lib_arm/armlinux.c
+
+* Patch by Stephen Williams, 15 Mar 2004:
+  Fix CONFIG_SERIAL_SOFTWARE_FIFO documentation
+
+* Patch by Tolunay Orkun, 15 Mar 2004:
+  Initialize bi_opbfreq to real OPB frequency via get_OPB_freq()
+
+* Patch by Travis Sawyer, 15 Mar 2004:
+  Update CREDITS & MAINTAINERS files for PPC440GX & Ocotea port
+
+* Add start-up delay to make sure power has stabilized before
+  attempting to switch on USB on SX1 board.
+
+* Patch by Josef Wagner, 18 Mar 2004:
+  - Add support for MicroSys XM250 board (PXA255)
+  - Add support for MicroSys PM828 board (MPC8280)
+  - Add support for 32 MB Flash on PM825/826
+  - new SDRAM refresh rate for PM825/PM826
+  - added support for MicroSys PM520 (MPC5200)
+  - replaced Query by Identify command in CPU86/flash.c
+    to support 28F160F3B
+
+* Fix wrap around problem with udelay() on ARM920T
+
+* Add support for Macronix flash on TRAB board
+
+* Patch by Pierre Aubert, 15 Mar 2004:
+  Fix buffer overflow in IDE identification
+
+* Fix power-off of LCD for out-of-band temperatures on LWMON board
+
+* Remove redundand #define in IceCube.h
+
+* Patch by Steven Scholz, 27 Feb 2004:
+  - Adding get_ticks() and get_tbclk() for AT91RM9200
+  - Many white space fixes in cpu/at91rm9200/interrupts.c
+
+* Patches by Steven Scholz, 20 Feb 2004:
+  some cleanup in AT91RM9200 related code
+
+* Patches by Travis Sawyer, 12 Mar 2004:
+  - Fix Gigabit Ethernet support for 440GX
+  - Add Gigabit Ethernet Support to MII PHY utilities
+
+* Patch by Brad Kemp, 12 Mar 2004:
+  Fixes for drivers/cfi_flash.c:
+  - Better support for x8/x16 implementations
+  - Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE
+  - Added defines for AMD command and address constants
+
+* Patch by Leon Kukovec, 12 Mar 2004:
+  Fix get_dentfromdir() to correctly handle deleted dentries
+
+* Patch by George G. Davis, 11 Mar 2004:
+  Remove hard coded network settings in TI OMAP1610 H2
+  default board config
+
+* Patch by George G. Davis, 11 Mar 2004:
+  add support for ADS GraphicsClient+ board.
+
+* Patch by Pierre Aubert, 11 Mar 2004:
+  - add bitmap command and splash screen support in cfb console
+  - add [optional] origin in the bitmap display command
+
+* Patch by Travis Sawyer, 11 Mar 2004:
+  Fix ocotea board early init interrupt setup.
+
+* Patch by Thomas Viehweger, 11 Mar 2004:
+  Remove redundand code; add  PCI-specific bits to include/mpc8260.h
+
+* Patch by Stephan Linz, 09 Mar 2004
+  - Add support for the SSV ADNP/ESC1 (Nios Softcore)
+
+* Patch by George G. Davis, 9 Mar 2004:
+  fix recent build failure for SA1100 target
+
+* Patch by Travis Sawyer, 09 Mar 2004:
+  Support native interrupt mode for the IBM440GX.
+  Previously it was running in 440GP compatibility mode.
+
+* Patch by Philippe Robin, 09 Mar 2004:
+  Added ARM Integrator AP, CP and Versatile PB926EJ-S Reference
+  Platform support.
+
+* Patch by Masami Komiya, 08 Mar 2004:
+  Don't overwrite server IP address or boot file name
+  when the boot server does not return values
+
+* Patch by Tolunay Orkun, 5 Mar 2004:
+  Removed compile time restriction on CFG_I2C_SPEED for DS1338 RTC
+
+* Patch by Tolunay Orkun, 5 Mar 2004:
+  Fix early board initialization for Cogent CSB272 board
+
+* Patch by Ed Okerson, 3 Mar 2004:
+  fix CFI flash writes for little endian systems
+
+* Patch by Reinhard Meyer, 01 Mar 2004:
+  generalize USB and IDE support for MPC5200 with according
+  changes to IceCube.h and TOP5200.h
+  add Am29LV256 256 MBit FLASH support for TOP5200 boards
+  add info about USB and IDE to README
+
+* Patch by Yuli Barcohen, 4 Mar 2004:
+  Fix problems with GCC 3.3.x which changed handling of global
+  variables explicitly initialized to zero (now in .bss instead of
+  .data as before).
+
+* Patch by Leon Kukovec, 02 Mar 2004:
+  add strswab() to fix IDE LBA capacity, firmware and model numbers
+  on little endian machines
+
+* Patch by Masami Komiya, 02 Mar 2004:
+  - Remove get_ticks() from NFS code
+  - Add verification of RPC transaction ID
+
+* Patch by Pierre Aubert, 02 Mar 2004:
+  cleanup for IDE and USB drivers for MPC5200
+
+* Patch by Travis Sawyer, 01 Mar 2004:
+  Ocotea:
+  - Add IBM PPC440GX Ref Platform support (Ocotea)
+    Original code by Paul Reynolds <PaulReynolds@lhsolutions.com>
+    Adapted to U-Boot and 440GX port
+  440gx_enet.c:
+  - Add gracious handling of all Ethernet Pin Selections for 440GX
+  - Add RGMII selection for Cicada CIS8201 Gigabit PHY
+  ppc440.h:
+  - Add needed bit definitions
+  - Fix formatting
+
+* Patch by Carl Riechers, 1 Mar 2004:
+  Add PPC440GX prbdv0 divider to fix memory clock calculation.
+
+* Patch by Stephan Linz, 27 Feb 2004
+  - avoid problems for targets without NFS download support
+
+* Patch by Rune Torgersen, 27 Feb 2004:
+  - Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
+  - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
+  - Added support for 64bit strtoul (CFG_64BIT_STRTOUL)
+
+* Patch by Masami Komiya, 27 Feb 2004:
+  Fix rarpboot: add autoload by NFS
+
+* Patch by Dan Eisenhut, 26 Feb 2004:
+  fix flash_write return value in saveenv
+
+* Patch by Stephan Linz, 11 Dec 2003
+  expand config.mk to avoid trigraph warnings on NIOS
+
+* Rename "BMS2003" board into "HMI10"
+
+* SX1 patches: use "serial#" for USB serial #; use redundand environment
+  storage; auto-set console on USB port (using preboot command)
+
 * Add support for SX1 mobile phone; add support for USB-based console
   (enable with "setenv stdout usbtty; setenv stdin usbtty")
 

CREDITS

@@ -28,16 +28,29 @@ D: ERIC Support
 
 N: Pantelis Antoniou
 E: panto@intracom.gr
-D: NETVIA board support, ARTOS support.
+D: NETVIA & NETPHONE board support, ARTOS support.
 
 N: Pierre Aubert
 E: <p.aubert@staubli.com>
 D: Support for RPXClassic board
 
+N: Yuli Barcohen
+E: yuli@arabellasw.com
+D: Unified support for Motorola MPC826xADS/MPC8272ADS/PQ2FADS boards.
+D: Support for Zephyr Engineering ZPC.1900 board.
+D: Support for Interphase iSPAN boards.
+D: Support for Analogue&Micro Adder boards.
+W: http://www.arabellasw.com
+
 N: Jerry van Baren
 E: <vanbaren@cideas.com>
 D: BedBug port to 603e core (MPC82xx). Code for enhanced memory test.
 
+N: Pavel Bartusek
+E: <pba@sysgo.com>
+D: Reiserfs support
+W: http://www.elinos.com
+
 N: Andre Beaudin
 E: <andre.beaudin@colubris.com>
 D: PCMCIA, Ethernet, TFTP
@@ -62,6 +75,12 @@ N: Oliver Brown
 E: obrown@adventnetworks.com
 D: Port to the gw8260 board
 
+N: Curt Brune
+E: curt@cucy.com
+D: Added support for Samsung S3C4510B CPU (ARM7tdmi based SoC)
+D: Added support for ESPD-Inc. EVB4510 Board
+W: http://www.cucy.com
+
 N: Jonathan De Bruyne
 E: jonathan.debruyne@siemens.atea.be
 D: Port to Siemens IAD210 board
@@ -78,6 +97,10 @@ N: Magnus Damm
 E: damm@opensource.se
 D: 8xxrom
 
+N: George G. Davis
+E: gdavis@mvista.com
+D: Board ports for ADS GraphicsClient+ and Intel Assabet
+
 N: Arun Dharankar
 E: ADharankar@ATTBI.Com
 D: threads / scheduler example code
@@ -183,6 +206,15 @@ N: Yoo. Jonghoon
 E: yooth@ipone.co.kr
 D: Added port to the RPXlite board
 
+N: Mark Jonas
+E: mark.jonas@freescale.com
+D: Support for Freescale Total5200 platform
+W: http://www.mobilegt.com/
+
+N: Sam Song
+E: samsongshu@yahoo.com.cn
+D: Port to the RPXlite_DW board
+
 N: Brad Kemp
 E: Brad.Kemp@seranoa.com
 D: Port to Windriver ppmc8260 board
@@ -204,6 +236,10 @@ N: Bernhard Kuhn
 E: bkuhn@metrowerks.com
 D Support for Coldfire CPU; Support for Motorola M5272C3 and M5282EVB boards
 
+N: Prakash Kumar
+E: prakash@embedx.com
+D  Support for Intrinsyc CERF PXA250 board.
+
 N: Thomas Lange
 E: thomas@corelatus.se
 D: Support for GTH and dbau1x00 boards; lots of PCMCIA fixes
@@ -216,6 +252,7 @@ W: http://www.leox.org
 N: Stephan Linz
 E: linz@li-pro.net
 D: Support for Nios Stratix Development Kit (DK-1S10)
+D: Support for SSV ADNP/ESC1 (Nios Cyclone)
 W: http://www.li-pro.net
 
 N: Raymond Lo
@@ -226,6 +263,11 @@ N: Dan Malek
 E: dan@netx4.com
 D: FADSROM, the grandfather of all of this
 
+N: Andrea "llandre" Marson
+E: andrea.marson@dave-tech.it
+D: Port to PPChameleonEVB board
+W: www.dave-tech.it
+
 N: Reinhard Meyer
 E: r.meyer@emk-elektronik.de
 D: Port to EMK TOP860 Module
@@ -251,6 +293,10 @@ E: rof@sysgo.de
 D: Initial support for SSV-DNP1110, SMC91111 driver
 W: www.elinos.com
 
+N: Tolunay Orkun
+E: torkun@nextio.com
+D: Support for Cogent CSB272 & CSB472 boards
+
 N: Keith Outwater
 E: keith_outwater@mvis.com
 D: Support for generic/custom MPC860T boards (GEN860T, GEN860T_SC)
@@ -265,10 +311,20 @@ D: Support for 4xx SCSI, floppy, CDROM, CT69000 video, ...
 D: Support for PIP405 board
 D: Support for MIP405 board
 
+N: Dave Peverley
+E: dpeverley@mpc-data.co.uk
+W: http://www.mpc-data.co.uk
+D: OMAP730 P2 board support
+
 N: Bill Pitts
 E: wlp@mindspring.com
 D: BedBug embedded debugger code
 
+N: Daniel Poirot
+E: dan.poirot@windriver.com
+D: Support for the sbc8240 board
+W: http://www.windriver.com
+
 N: Stefan Roese
 E: stefan.roese@esd-electronics.com
 D: IBM PPC401/403/405GP Support; Windows environment support
@@ -277,13 +333,17 @@ N: Erwin Rol
 E: erwin@muffin.org
 D: boot support for RTEMS
 
+N: Paul Ruhland
+E: pruhland@rochester.rr.com
+D: Port to Logic Zoom LH7A40x SDK board(s)
+
 N: Neil Russell
 E: caret@c-side.com
 D: Author of LiMon-1.4.2, which contributed some ideas
 
 N: Travis B. Sawyer
 E: travis.sawyer@sandburst.com
-D: Support for IBM PPC440GX, XES XPedite1000 440GX PrPMC board.
+D: Support for IBM PPC440GX, XES XPedite1000 440GX PrPMC board.  IBM 440gx Ref Platform (Ocotea)
 
 N: Paolo Scaffardi
 E: arsenio@tin.it
@@ -293,6 +353,19 @@ N: Robert Schwebel
 E: r.schwebel@pengutronix.de
 D: Support for csb226, logodl and innokom boards (PXA2xx)
 
+N: Yasushi Shoji
+E: yashi@atmark-techno.com
+D: Support for Xilinx MicroBlaze, for Atmark Techno SUZAKU FPGA board
+
+N: Kurt Stremerch
+E: kurt@exys.be
+D: Support for Exys XSEngine board
+
+N: Andrea Scian
+E: andrea.scian@dave-tech.it
+D: Port to B2 board
+W: www.dave-tech.it
+
 N: Rob Taylor
 E: robt@flyingpig.com
 D: Port to MBX860T and Sandpoint8240
@@ -313,13 +386,22 @@ N: David Updegraff
 E: dave@cray.com
 D: Port to Cray L1 board; DHCP vendor extensions
 
+N: Christian Vejlbo
+E: christian.vejlbo@tellabs.com
+D: FADS860T ethernet support
+
 N: Martin Winistoerfer
 E: martinwinistoerfer@gmx.ch
 D: Port to MPC555/556 microcontrollers and support for cmi board
 
-N: Christian Vejlbo
-E: christian.vejlbo@tellabs.com
-D: FADS860T ethernet support
+N: Ming-Len Wu
+E: minglen_wu@techware.com.tw
+D: Motorola MX1ADS board support
+W: http://www.techware.com.tw/
+
+N: Xianghua Xiao
+E: x.xiao@motorola.com
+D: Support for Motorola 85xx(PowerQUICC III) chip, MPC8540ADS and MPC8560ADS boards.
 
 N: John Zhan
 E: zhanz@sinovee.com
@@ -329,7 +411,3 @@ N: Alex Zuepke
 E: azu@sysgo.de
 D: Overall improvements on StrongARM, ARM720TDMI; Support for Tuxscreen; initial PCMCIA support for ARM
 W: www.elinos.com
-
-N: Xianghua Xiao
-E: x.xiao@motorola.com
-D: Support for Motorola 85xx(PowerQUICC III) chip, MPC8540ADS and MPC8560ADS boards.

MAINTAINERS

@@ -27,6 +27,9 @@ Pantelis Antoniou <panto@intracom.gr>
 
 Yuli Barcohen <yuli@arabellasw.com>
 
+	Adder			MPC87x/MPC852T
+	ISPAN			MPC8260
+	MPC8260ADS		MPC826x/MPC827x/MPC8280
 	ZPC1900			MPC8265
 
 Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
@@ -97,7 +100,6 @@ Wolfgang Denk <wd@denx.de>
 	TQM8255			MPC8255
 
 	CPU86			MPC8260
-	PM825			MPC8250
 	PM826			MPC8260
 	TQM8260			MPC8260
 
@@ -146,6 +148,7 @@ Bill Hargen <Bill_Hargen@Jabil.com>
 Klaus Heydeck <heydeck@kieback-peter.de>
 
 	KUP4K			MPC855
+	KUP4X			MPC859
 
 Murray Jensen <Murray.Jensen@cmst.csiro.au>
 
@@ -162,10 +165,6 @@ Sangmoon Kim <dogoil@etinsys.com>
 
 	debris			MPC8245
 
-Raghu Krishnaprasad <raghu.krishnaprasad@fci.com>
-
-	ADDERII			MPC852T
-
 Nye Liu <nyet@zumanetworks.com>
 
 	ZUMA			MPC7xx_74xx
@@ -182,6 +181,10 @@ Eran Man <eran@nbase.co.il>
 
 	EVB64260_750CX		MPC750CX
 
+Andrea "llandre" Marson <andrea.marson@dave-tech.it>
+
+	PPChameleonEVB	PPC405EP
+
 Reinhard Meyer <r.meyer@emk-elektronik.de>
 
 	TOP860			MPC860T
@@ -192,7 +195,8 @@ Scott McNutt <smcnutt@artesyncp.com>
 	EBONY			PPC440GP
 
 Tolunay Orkun <torkun@nextio.com>
-	csb272			PPC4xx
+	csb272			PPC405GP
+	csb472			PPC405GP
 
 Keith Outwater <Keith_Outwater@mvis.com>
 
@@ -230,6 +234,11 @@ Stefan Roese <stefan.roese@esd-electronics.com>
 	PMC405			PPC405GP
 	VOH405			PPC405EP
 
+Travis Sawyer (travis.sawyer@sandburst.com>
+
+	XPEDITE1K		PPC440GX
+	OCOTEA			PPC440GX
+
 Peter De Schrijver <p2@mind.be>
 
 	ML2			PPC4xx
@@ -248,15 +257,28 @@ Rune Torgersen <runet@innovsys.com>
 
 	MPC8266ADS		MPC8266
 
+Josef Wagner <Wagner@Microsys.de>
+
+	CPC45			MPC8245
+	PM520			MPC5200
+
+Stephen Williams <steve@icarus.com>
+
+	JSE			PPC405GPr
+
 John Zhan <zhanz@sinovee.com>
 
 	svm_sc8xx		MPC8xx
 
-Xianghua Xiao <x.xiao@motorola.com>
+Jon Loeliger <jdl@freescale.com>
 
 	MPC8540ADS		MPC8540
 	MPC8560ADS		MPC8560
 
+Dan Malek <dan@embeddededge.com>
+
+	STxGP3			MPC85xx
+
 -------------------------------------------------------------------------
 
 Unknown / orphaned boards:
@@ -279,7 +301,6 @@ Unknown / orphaned boards:
 
 	MOUSSE			MPC824x
 
-	MPC8260ADS		MPC8260
 	RPXsuper		MPC8260
 	rsdproto		MPC8260
 
@@ -293,6 +314,11 @@ Unknown / orphaned boards:
 #	Board			CPU					#
 #########################################################################
 
+George G. Davis <gdavis@mvista.com>
+
+	assabet			SA1100
+	gcplus			SA1100
+
 Thomas Elste <info@elste.org>
 
 	modnet50		ARM720T (NET+50)
@@ -317,15 +343,26 @@ Gary Jennejohn <gj@denx.de>
 	smdk2400		ARM920T
 	trab			ARM920T
 
+Prakash Kumar <prakash@embedx.com>
+
+	cerf250			xscale
+
 Kshitij Gupta <kshitij@ti.com>
 
 	omap1510inn		ARM925T
 	omap1610inn		ARM926EJS
 
+Dave Peverley <dpeverley@mpc-data.co.uk>
+	omap730p2		ARM926EJS
+
 Nishant Kamat <nskamat@ti.com>
 
 	omap1610h2		ARM926EJS
 
+Rishi Bhattacharya <rishi@ti.com>
+
+	omap5912osk		ARM926EJS
+
 David M<>ller <d.mueller@elsoft.ch>
 
 	smdk2410		ARM920T
@@ -340,6 +377,10 @@ Robert Schwebel <r.schwebel@pengutronix.de>
 	csb226			xscale
 	innokom			xscale
 
+Andrea Scian <andrea.scian@dave-tech.it>
+
+	B2				ARM7TDMI (S3C44B0X)
+
 Alex Z<>pke <azu@sysgo.de>
 
 	lart			SA1100
@@ -381,11 +422,23 @@ Thomas Lange <thomas@corelatus.se>
 Stephan Linz <linz@li-pro.net>
 
 	DK1S10			Nios-32
+	ADNPESC1		Nios-32
 
 Scott McNutt <smcnutt@psyent.com>
 
 	DK1C20			Nios-32
 
+#########################################################################
+# MicroBlaze Systems:							#
+#									#
+# Maintainer Name, Email Address					#
+#	Board			CPU					#
+#########################################################################
+
+Yasushi Shoji <yashi@atmark-techno.com>
+
+	SUZAKU			MicroBlaze
+
 #########################################################################
 # End of MAINTAINERS list						#
 #########################################################################

MAKEALL

@@ -25,7 +25,8 @@ LIST_5xx="	\
 #########################################################################
 
 LIST_5xxx="	\
-	IceCube_5100	IceCube_5200	EVAL5200	\
+	icecube_5100	icecube_5200	EVAL5200	PM520		\
+	Total5100	Total5200	Total5200_Rev2	TQM5200_AA	\
 "
 
 #########################################################################
@@ -33,22 +34,23 @@ LIST_5xxx="	\
 #########################################################################
 
 LIST_8xx="	\
-	AdderII		ADS860		AMX860		c2mon		\
-	CCM		cogent_mpc8xx	DUET_ADS	ESTEEM192E	\
-	ETX094		ELPT860		FADS823		FADS850SAR	\
-	FADS860T	FLAGADM		FPS850L		GEN860T		\
-	GEN860T_SC	GENIETV		GTH		hermes		\
-	IAD210		ICU862_100MHz	IP860		IVML24		\
-	IVML24_128	IVML24_256	IVMS8		IVMS8_128	\
-	IVMS8_256	KUP4K		LANTEC		lwmon		\
-	MBX		MBX860T		MHPC		MPC86xADS	\
-	MVS1		NETVIA		NETVIA_V2	NX823		\
-	pcu_e		QS823		QS850		QS860T		\
-	R360MPI		RBC823		rmu		RPXClassic	\
-	RPXlite		RRvision	SM850		SPD823TS	\
-	svm_sc8xx	SXNI855T	TOP860		TQM823L		\
-	TQM823L_LCD	TQM850L		TQM855L		TQM860L		\
-	v37								\
+	Adder87x	GENIETV		MBX860T		RBC823		\
+	AdderII		GTH		MHPC		rmu		\
+	ADS860		hermes		MPC86xADS	RPXClassic	\
+	AMX860		IAD210		MPC885ADS	RPXlite		\
+	c2mon		ICU862_100MHz	MVS1		RPXlite_DW	\
+	CCM		IP860		NETPHONE	RRvision	\
+	cogent_mpc8xx	IVML24		NETTA		SM850		\
+	ELPT860		IVML24_128	NETTA2		SPD823TS	\
+	ESTEEM192E	IVML24_256	NETTA_ISDN	svm_sc8xx	\
+	ETX094		IVMS8		NETVIA		SXNI855T	\
+	FADS823		IVMS8_128	NETVIA_V2	TOP860		\
+	FADS850SAR	IVMS8_256	NX823		TQM823L		\
+	FADS860T	KUP4K		pcu_e		TQM823L_LCD	\
+	FLAGADM		KUP4X		QS823		TQM850L		\
+	FPS850L		LANTEC		QS850		TQM855L		\
+	GEN860T		lwmon		QS860T		TQM860L		\
+	GEN860T_SC	MBX		R360MPI		v37		\
 "
 
 #########################################################################
@@ -59,12 +61,13 @@ LIST_4xx="	\
 	ADCIOP		AR405		ASH405		BUBINGA405EP	\
 	CANBT		CPCI405		CPCI4052	CPCI405AB	\
 	CPCI440		CPCIISER4	CRAYL1		csb272		\
-	DASA_SIM	DP405		DU405		EBONY		\
-	ERIC		EXBITGEN	HUB405		MIP405		\
-	MIP405T		ML2		ml300		OCRTC		\
-	ORSG		PCI405		PIP405		PLU405		\
-	PMC405		PPChameleonEVB	VOH405		W7OLMC		\
-	W7OLMG		WALNUT405	XPEDITE1K			\
+	csb472		DASA_SIM	DP405		DU405		\
+	EBONY		ERIC		EXBITGEN	HUB405		\
+	JSE		MIP405		MIP405T		ML2		\
+	ml300		OCOTEA		OCRTC		ORSG		\
+	PCI405		PIP405		PLU405		PMC405		\
+	PPChameleonEVB	VOH405		W7OLMC		W7OLMG		\
+	WALNUT405	XPEDITE1K					\
 "
 
 #########################################################################
@@ -75,7 +78,7 @@ LIST_824x="	\
 	A3000		BMW		CPC45		CU824		\
 	debris		eXalion		MOUSSE		MUSENKI		\
 	MVBLUE		OXC		PN62		Sandpoint8240	\
-	Sandpoint8245	SL8245		utx8245				\
+	Sandpoint8245	SL8245		utx8245		sbc8240	\
 "
 
 #########################################################################
@@ -84,8 +87,9 @@ LIST_824x="	\
 
 LIST_8260="	\
 	atc		cogent_mpc8260	CPU86		ep8260		\
-	gw8260		hymod		IPHASE4539	MPC8260ADS	\
-	MPC8266ADS	PM826		ppmc8260	RPXsuper	\
+	gw8260		hymod		IPHASE4539	ISPAN		\
+	MPC8260ADS	MPC8266ADS	MPC8272ADS	PM826		\
+	PM828		ppmc8260	PQ2FADS		RPXsuper	\
 	rsdproto	sacsng		sbc8260		SCM		\
 	TQM8260_AC	TQM8260_AD	TQM8260_AE	ZPC1900		\
 "
@@ -95,7 +99,7 @@ LIST_8260="	\
 #########################################################################
 
 LIST_85xx="	\
-	MPC8540ADS	MPC8560ADS					\
+	MPC8540ADS	MPC8560ADS	sbc8560		stxgp3		\
 "
 
 #########################################################################
@@ -122,29 +126,30 @@ LIST_ppc="${LIST_5xx}  ${LIST_5xxx} \
 ## StrongARM Systems
 #########################################################################
 
-LIST_SA="dnp1110 lart shannon"
+LIST_SA="assabet dnp1110 gcplus lart shannon"
 
 #########################################################################
 ## ARM7 Systems
 #########################################################################
 
-LIST_ARM7="B2 ep7312 impa7"
+LIST_ARM7="B2 ep7312 evb4510 impa7 modnet50"
 
 #########################################################################
 ## ARM9 Systems
 #########################################################################
 
 LIST_ARM9="	\
-	at91rm9200dk	omap1510inn	omap1610h2	omap1610inn	\
-	smdk2400	smdk2410	trab				\
-	VCMA9								\
+	at91rm9200dk	integratorcp	integratorap 	lpd7a400	\
+	mx1ads		mx1fs2		omap1510inn	omap1610h2	\
+	omap1610inn	omap730p2	scb9328		smdk2400	\
+	smdk2410	trab		VCMA9		versatile	\
 "
 
 #########################################################################
 ## Xscale Systems
 #########################################################################
 
-LIST_pxa="cradle csb226 innokom lubbock wepep250"
+LIST_pxa="cerf250 cradle csb226 innokom lubbock wepep250 xm250 xsengine"
 
 LIST_ixp="ixdp425"
 
@@ -176,10 +181,18 @@ LIST_x86="${LIST_I486}"
 #########################################################################
 
 LIST_nios="	\
+	ADNPESC1 ADNPESC1_base_32					\
+	ADNPESC1_DNPEVA2_base_32					\
 	DK1C20 DK1C20_standard_32					\
 	DK1S10 DK1S10_standard_32 DK1S10_mtx_ldk_20			\
 "
 
+#########################################################################
+## MicroBlaze Systems
+#########################################################################
+
+LIST_microblaze="suzaku"
+
 #-----------------------------------------------------------------------
 
 #----- for now, just run PPC by default -----
@@ -204,6 +217,7 @@ do
 	case "$arg" in
 	ppc|5xx|5xxx|8xx|824x|8260|85xx|4xx|7xx|74xx| \
 	arm|SA|ARM7|ARM9|pxa|ixp| \
+	microblaze| \
 	mips| \
 	nios| \
 	x86|I486)

Makefile

@@ -75,6 +75,9 @@ endif
 ifeq ($(ARCH),m68k)
 CROSS_COMPILE = m68k-elf-
 endif
+ifeq ($(ARCH),microblaze)
+CROSS_COMPILE = mb-
+endif
 endif
 endif
 
@@ -99,7 +102,8 @@ LIBS  = lib_generic/libgeneric.a
 LIBS += board/$(BOARDDIR)/lib$(BOARD).a
 LIBS += cpu/$(CPU)/lib$(CPU).a
 LIBS += lib_$(ARCH)/lib$(ARCH).a
-LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a
+LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a \
+	fs/reiserfs/libreiserfs.a
 LIBS += net/libnet.a
 LIBS += disk/libdisk.a
 LIBS += rtc/librtc.a
@@ -111,7 +115,8 @@ LIBS += common/libcommon.a
 .PHONY : $(LIBS)
 
 # Add GCC lib
-PLATFORM_LIBS += -L $(shell dirname `$(CC) $(CFLAGS) -print-libgcc-file-name`) -lgcc
+PLATFORM_LIBS += --no-warn-mismatch -L $(shell dirname `$(CC) $(CFLAGS) -print-libgcc-file-name`) -lgcc
+
 
 # The "tools" are needed early, so put this first
 # Don't include stuff already done in $(LIBS)
@@ -164,6 +169,9 @@ depend dep:
 
 tags:
 		ctags -w `find $(SUBDIRS) include \
+				lib_generic board/$(BOARDDIR) cpu/$(CPU) lib_$(ARCH) \
+				fs/cramfs fs/fat fs/fdos fs/jffs2 \
+				net disk rtc dtt drivers drivers/sk98lin common \
 			\( -name CVS -prune \) -o \( -name '*.[ch]' -print \)`
 
 etags:
@@ -185,7 +193,7 @@ endif
 #########################################################################
 
 unconfig:
-	rm -f include/config.h include/config.mk
+	@rm -f include/config.h include/config.mk board/*/config.tmp
 
 #========================================================================
 # PowerPC
@@ -198,30 +206,34 @@ unconfig:
 cmi_mpc5xx_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc5xx cmi
 
-PATI_config:unconfig
+PATI_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc5xx pati mpl
 
 #########################################################################
 ## MPC5xxx Systems
 #########################################################################
-MPC5200LITE_config		\
-MPC5200LITE_LOWBOOT_config	\
-MPC5200LITE_LOWBOOT08_config	\
-icecube_5200_DDR_config		\
-IceCube_5200_DDR_config		\
-icecube_5200_DDR_LOWBOOT_config \
-icecube_5200_DDR_LOWBOOT08_config \
-icecube_5200_config		\
-IceCube_5200_config		\
-IceCube_5100_config:		unconfig
+Lite5200_config				\
+Lite5200_LOWBOOT_config			\
+Lite5200_LOWBOOT08_config		\
+icecube_5200_config			\
+icecube_5200_LOWBOOT_config		\
+icecube_5200_LOWBOOT08_config		\
+icecube_5200_DDR_config 		\
+icecube_5200_DDR_LOWBOOT_config 	\
+icecube_5200_DDR_LOWBOOT08_config	\
+icecube_5100_config:			unconfig
 	@ >include/config.h
-	@[ -z "$(findstring LOWBOOT,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFF000000" >board/icecube/config.tmp ; \
+	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
+		{ if [ "$(findstring DDR,$@)" ] ; \
+			then echo "TEXT_BASE = 0xFF800000" >board/icecube/config.tmp ; \
+			else echo "TEXT_BASE = 0xFF000000" >board/icecube/config.tmp ; \
+		  fi ; \
 		  echo "... with LOWBOOT configuration" ; \
 		}
 	@[ -z "$(findstring LOWBOOT08,$@)" ] || \
 		{ echo "TEXT_BASE = 0xFF800000" >board/icecube/config.tmp ; \
 		  echo "... with 8 MB flash only" ; \
+		  echo "... with LOWBOOT configuration" ; \
 		}
 	@[ -z "$(findstring DDR,$@)" ] || \
 		{ echo "#define CONFIG_MPC5200_DDR"	>>include/config.h ; \
@@ -237,33 +249,104 @@ IceCube_5100_config:		unconfig
 		}
 	@./mkconfig -a IceCube ppc mpc5xxx icecube
 
+PM520_config \
+PM520_DDR_config \
+PM520_ROMBOOT_config \
+PM520_ROMBOOT_DDR_config:	unconfig
+	@ >include/config.h
+	@[ -z "$(findstring DDR,$@)" ] || \
+		{ echo "#define CONFIG_MPC5200_DDR"	>>include/config.h ; \
+		  echo "... DDR memory revision" ; \
+		}
+	@[ -z "$(findstring ROMBOOT,$@)" ] || \
+		{ echo "#define CONFIG_BOOT_ROM" >>include/config.h ; \
+		  echo "... booting from 8-bit flash" ; \
+		}
+	@./mkconfig -a PM520 ppc mpc5xxx pm520
+
 MINI5200_config	\
 EVAL5200_config	\
 TOP5200_config:	unconfig
 	@ echo "#define CONFIG_$(@:_config=) 1"	>include/config.h
 	@./mkconfig -a TOP5200 ppc mpc5xxx top5200 emk
 
+Total5100_config		\
+Total5200_config		\
+Total5200_lowboot_config	\
+Total5200_Rev2_config		\
+Total5200_Rev2_lowboot_config:	unconfig
+	@ >include/config.h
+	@[ -z "$(findstring 5100,$@)" ] || \
+		{ echo "#define CONFIG_MGT5100"		>>include/config.h ; \
+		  echo "... with MGT5100 processor" ; \
+		}
+	@[ -z "$(findstring 5200,$@)" ] || \
+		{ echo "#define CONFIG_MPC5200"		>>include/config.h ; \
+		  echo "... with MPC5200 processor" ; \
+		}
+	@[ -n "$(findstring Rev,$@)" ] || \
+		{ echo "#define CONFIG_TOTAL5200_REV 1"	>>include/config.h ; \
+		  echo "... revision 1 board" ; \
+		}
+	@[ -z "$(findstring Rev2_,$@)" ] || \
+		{ echo "#define CONFIG_TOTAL5200_REV 2"	>>include/config.h ; \
+		  echo "... revision 2 board" ; \
+		}
+	@[ -z "$(findstring lowboot_,$@)" ] || \
+		{ echo "TEXT_BASE = 0xFE000000" >board/total5200/config.tmp ; \
+		  echo "... with lowboot configuration" ; \
+		}
+	@./mkconfig -a Total5200 ppc mpc5xxx total5200
+
+TQM5200_AA_config	\
+TQM5200_AB_config	\
+TQM5200_AC_config	\
+MiniFAP_config:	unconfig
+	@ >include/config.h
+	@[ -z "$(findstring MiniFAP,$@)" ] || \
+		{ echo "#define CONFIG_MINIFAP"	>>include/config.h ; \
+		  echo "#define CONFIG_TQM5200_AC"	>>include/config.h ; \
+		  echo "... TQM5200_AC on MiniFAP" ; \
+		}
+	@[ -z "$(findstring AA,$@)" ] || \
+		{ echo "#define CONFIG_TQM5200_AA"	>>include/config.h ; \
+		  echo "... with 4 MB Flash, 16 MB SDRAM, 32 kB EEPROM" ; \
+		}
+	@[ -z "$(findstring AB,$@)" ] || \
+		{ echo "#define CONFIG_TQM5200_AB"	>>include/config.h ; \
+		  echo "... with 64 MB Flash, 64 MB SDRAM, 32 kB EEPROM, 512 kB SRAM" ; \
+		  echo "... with Graphics Controller"; \
+		}
+	@[ -z "$(findstring AC,$@)" ] || \
+		{ echo "#define CONFIG_TQM5200_AC"	>>include/config.h ; \
+		  echo "... with 4 MB Flash, 128 MB SDRAM" ; \
+		  echo "... with Graphics Controller"; \
+		}
+	@./mkconfig -a TQM5200 ppc mpc5xxx tqm5200
+
 #########################################################################
 ## MPC8xx Systems
 #########################################################################
 
-AdderII_config:	unconfig
-	@./mkconfig $(@:_config=) ppc mpc8xx adderII
+Adder_config    \
+Adder87x_config \
+AdderII_config  \
+	:		unconfig
+	$(if $(findstring AdderII,$@), \
+	@echo "#define CONFIG_MPC852T" > include/config.h)
+	@./mkconfig -a Adder ppc mpc8xx adder
 
 ADS860_config     \
-DUET_ADS_config   \
 FADS823_config    \
 FADS850SAR_config \
 MPC86xADS_config  \
+MPC885ADS_config  \
 FADS860T_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx fads
 
 AMX860_config	:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx amx860 westel
 
-bms2003_config	:	unconfig
-	@./mkconfig $(@:_config=) ppc mpc8xx tqm8xx
-
 c2mon_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx c2mon
 
@@ -305,6 +388,9 @@ GTH_config:	unconfig
 hermes_config	:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx hermes
 
+HMI10_config	:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc8xx tqm8xx
+
 IAD210_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx IAD210 siemens
 
@@ -353,7 +439,10 @@ IVMS8_config:	unconfig
 	@./mkconfig -a IVMS8 ppc mpc8xx ivm
 
 KUP4K_config	:	unconfig
-	@./mkconfig $(@:_config=) ppc mpc8xx kup4k
+	@./mkconfig $(@:_config=) ppc mpc8xx kup4k kup
+
+KUP4X_config    :       unconfig
+	@./mkconfig $(@:_config=) ppc mpc8xx kup4x kup
 
 LANTEC_config	:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx lantec
@@ -386,6 +475,63 @@ NETVIA_config:		unconfig
 		 }
 	@./mkconfig -a $(call xtract_NETVIA,$@) ppc mpc8xx netvia
 
+xtract_NETPHONE = $(subst _V2,,$(subst _config,,$1))
+
+NETPHONE_V2_config \
+NETPHONE_config:	unconfig
+	@ >include/config.h
+	@[ -z "$(findstring NETPHONE_config,$@)" ] || \
+		 { echo "#define CONFIG_NETPHONE_VERSION 1" >>include/config.h ; \
+		 }
+	@[ -z "$(findstring NETPHONE_V2_config,$@)" ] || \
+		 { echo "#define CONFIG_NETPHONE_VERSION 2" >>include/config.h ; \
+		 }
+	@./mkconfig -a $(call xtract_NETPHONE,$@) ppc mpc8xx netphone
+
+xtract_NETTA = $(subst _SWAPHOOK,,$(subst _6412,,$(subst _ISDN,,$(subst _config,,$1))))
+
+NETTA_ISDN_6412_SWAPHOOK_config \
+NETTA_ISDN_SWAPHOOK_config \
+NETTA_6412_SWAPHOOK_config \
+NETTA_SWAPHOOK_config \
+NETTA_ISDN_6412_config \
+NETTA_ISDN_config \
+NETTA_6412_config \
+NETTA_config:		unconfig
+	@ >include/config.h
+	@[ -z "$(findstring ISDN_,$@)" ] || \
+		 { echo "#define CONFIG_NETTA_ISDN 1" >>include/config.h ; \
+		 }
+	@[ -n "$(findstring ISDN_,$@)" ] || \
+		 { echo "#undef CONFIG_NETTA_ISDN" >>include/config.h ; \
+		 }
+	@[ -z "$(findstring 6412_,$@)" ] || \
+		 { echo "#define CONFIG_NETTA_6412 1" >>include/config.h ; \
+		 }
+	@[ -n "$(findstring 6412_,$@)" ] || \
+		 { echo "#undef CONFIG_NETTA_6412" >>include/config.h ; \
+		 }
+	@[ -z "$(findstring SWAPHOOK_,$@)" ] || \
+		 { echo "#define CONFIG_NETTA_SWAPHOOK 1" >>include/config.h ; \
+		 }
+	@[ -n "$(findstring SWAPHOOK_,$@)" ] || \
+		 { echo "#undef CONFIG_NETTA_SWAPHOOK" >>include/config.h ; \
+		 }
+	@./mkconfig -a $(call xtract_NETTA,$@) ppc mpc8xx netta
+
+xtract_NETTA2 = $(subst _V2,,$(subst _config,,$1))
+
+NETTA2_V2_config \
+NETTA2_config:		unconfig
+	@ >include/config.h
+	@[ -z "$(findstring NETTA2_config,$@)" ] || \
+		 { echo "#define CONFIG_NETTA2_VERSION 1" >>include/config.h ; \
+		 }
+	@[ -z "$(findstring NETTA2_V2_config,$@)" ] || \
+		 { echo "#define CONFIG_NETTA2_VERSION 2" >>include/config.h ; \
+		 }
+	@./mkconfig -a $(call xtract_NETTA2,$@) ppc mpc8xx netta2
+
 NX823_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx nx823
 
@@ -413,6 +559,30 @@ RPXClassic_config:	unconfig
 RPXlite_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx RPXlite
 
+RPXlite_DW_64_config  		\
+RPXlite_DW_LCD_config 		\
+RPXlite_DW_64_LCD_config 	\
+RPXlite_DW_NVRAM_config		\
+RPXlite_DW_NVRAM_64_config      \
+RPXlite_DW_NVRAM_LCD_config	\
+RPXlite_DW_NVRAM_64_LCD_config  \
+RPXlite_DW_config:         unconfig
+	@ >include/config.h
+	@[ -z "$(findstring _64,$@)" ] || \
+		{ echo "#define RPXlite_64MHz"		>>include/config.h ; \
+		  echo "... with 64MHz system clock ..."; \
+		}
+	@[ -z "$(findstring _LCD,$@)" ] || \
+		{ echo "#define CONFIG_LCD"          	>>include/config.h ; \
+		  echo "#define CONFIG_NEC_NL6448BC20"	>>include/config.h ; \
+		  echo "... with LCD display ..."; \
+		}
+	@[ -z "$(findstring _NVRAM,$@)" ] || \
+		{ echo "#define  CFG_ENV_IS_IN_NVRAM" 	>>include/config.h ; \
+		  echo "... with ENV in NVRAM ..."; \
+		}
+	@./mkconfig -a RPXlite_DW ppc mpc8xx RPXlite_dw
+
 rmu_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx rmu
 
@@ -442,66 +612,26 @@ TOP860_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx top860 emk
 
 # Play some tricks for configuration selection
-# All boards can come with 50 MHz (default), 66MHz, 80MHz or 100 MHz clock,
-# but only 855 and 860 boards may come with FEC
-# and 823 boards may have LCD support
-xtract_8xx = $(subst _66MHz,,$(subst _80MHz,,$(subst _100MHz,,$(subst _133MHz,,$(subst _LCD,,$(subst _config,,$1))))))
+# Only 855 and 860 boards may come with FEC
+# and only 823 boards may have LCD support
+xtract_8xx = $(subst _LCD,,$(subst _config,,$1))
 
 FPS850L_config		\
 FPS860L_config		\
 NSCU_config		\
 TQM823L_config		\
-TQM823L_66MHz_config	\
-TQM823L_80MHz_config	\
 TQM823L_LCD_config	\
-TQM823L_LCD_66MHz_config \
-TQM823L_LCD_80MHz_config \
 TQM850L_config		\
-TQM850L_66MHz_config	\
-TQM850L_80MHz_config	\
 TQM855L_config		\
-TQM855L_66MHz_config	\
-TQM855L_80MHz_config	\
 TQM860L_config		\
-TQM860L_66MHz_config	\
-TQM860L_80MHz_config	\
 TQM862L_config		\
-TQM862L_66MHz_config	\
-TQM862L_80MHz_config	\
 TQM823M_config		\
-TQM823M_66MHz_config	\
-TQM823M_80MHz_config	\
 TQM850M_config		\
-TQM850M_66MHz_config	\
-TQM850M_80MHz_config	\
 TQM855M_config		\
-TQM855M_66MHz_config	\
-TQM855M_80MHz_config	\
 TQM860M_config		\
-TQM860M_66MHz_config	\
-TQM860M_80MHz_config	\
 TQM862M_config		\
-TQM862M_66MHz_config	\
-TQM862M_80MHz_config	\
-TQM862M_100MHz_config	\
 TQM866M_config:		unconfig
 	@ >include/config.h
-	@[ -z "$(findstring _66MHz,$@)" ] || \
-		{ echo "#define CONFIG_66MHz"		>>include/config.h ; \
-		  echo "... with 66MHz system clock" ; \
-		}
-	@[ -z "$(findstring _80MHz,$@)" ] || \
-		{ echo "#define CONFIG_80MHz"		>>include/config.h ; \
-		  echo "... with 80MHz system clock" ; \
-		}
-	@[ -z "$(findstring _100MHz,$@)" ] || \
-		{ echo "#define CONFIG_100MHz"		>>include/config.h ; \
-		  echo "... with 100MHz system clock" ; \
-		}
-	@[ -z "$(findstring _133MHz,$@)" ] || \
-		{ echo "#define CONFIG_133MHz"		>>include/config.h ; \
-		  echo "... with 133MHz system clock" ; \
-		}
 	@[ -z "$(findstring _LCD,$@)" ] || \
 		{ echo "#define CONFIG_LCD"		>>include/config.h ; \
 		  echo "#define CONFIG_NEC_NL6448BC20"	>>include/config.h ; \
@@ -527,7 +657,7 @@ wtk_config:	unconfig
 #########################################################################
 ## PPC4xx Systems
 #########################################################################
-xtract_4xx = $(subst _MODEL_BA,,$(subst _MODEL_ME,,$(subst _MODEL_HI,,$(subst _config,,$1))))
+xtract_4xx = $(subst _25,,$(subst _33,,$(subst _BA,,$(subst _ME,,$(subst _HI,,$(subst _config,,$1))))))
 
 ADCIOP_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx adciop esd
@@ -538,12 +668,17 @@ AR405_config:	unconfig
 ASH405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ash405 esd
 
-BUBINGA405EP_config:unconfig
+BUBINGA405EP_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx bubinga405ep
 
 CANBT_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx canbt esd
 
+CATcenter_config:	unconfig
+	@ echo "/* CATcenter uses PPChameleon Model ME */"  > include/config.h
+	@ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >> include/config.h
+	@./mkconfig -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave
+
 CPCI405_config	\
 CPCI4052_config	\
 CPCI405AB_config:	unconfig
@@ -556,12 +691,15 @@ CPCI440_config:	unconfig
 CPCIISER4_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx cpciiser4 esd
 
-CRAYL1_config:unconfig
+CRAYL1_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx L1 cray
 
 csb272_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx csb272
 
+csb472_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx csb472
+
 DASA_SIM_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx dasa_sim esd
 
@@ -571,32 +709,38 @@ DP405_config:	unconfig
 DU405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx du405 esd
 
-EBONY_config:unconfig
+EBONY_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ebony
 
-ERIC_config:unconfig
+ERIC_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx eric
 
-EXBITGEN_config:unconfig
+EXBITGEN_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx exbitgen
 
 HUB405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx hub405 esd
 
-MIP405_config:unconfig
+JSE_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx jse
+
+MIP405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx mip405 mpl
 
-MIP405T_config:unconfig
+MIP405T_config:	unconfig
 	@echo "#define CONFIG_MIP405T" >include/config.h
 	@echo "Enable subset config for MIP405T"
 	@./mkconfig -a MIP405 ppc ppc4xx mip405 mpl
 
-ML2_config:unconfig
+ML2_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ml2
 
-ml300_config:unconfig
+ml300_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ml300 xilinx
 
+OCOTEA_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx ocotea
+
 OCRTC_config		\
 ORSG_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ocrtc esd
@@ -604,7 +748,7 @@ ORSG_config:	unconfig
 PCI405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx pci405 esd
 
-PIP405_config:unconfig
+PIP405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx pip405 mpl
 
 PLU405_config:	unconfig
@@ -613,10 +757,13 @@ PLU405_config:	unconfig
 PMC405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx pmc405 esd
 
-PPChameleonEVB_MODEL_BA_config	\
-PPChameleonEVB_MODEL_ME_config	\
-PPChameleonEVB_MODEL_HI_config	\
-PPChameleonEVB_config:	unconfig
+PPChameleonEVB_config		\
+PPChameleonEVB_BA_25_config	\
+PPChameleonEVB_ME_25_config	\
+PPChameleonEVB_HI_25_config	\
+PPChameleonEVB_BA_33_config	\
+PPChameleonEVB_ME_33_config	\
+PPChameleonEVB_HI_33_config:	unconfig
 	@ >include/config.h
 	@[ -z "$(findstring _MODEL_BA,$@)" ] || \
 		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 0" >>include/config.h ; \
@@ -630,6 +777,14 @@ PPChameleonEVB_config:	unconfig
 		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 2" >>include/config.h ; \
 		  echo "... HIGH-END model" ; \
 		}
+	@[ -z "$(findstring _25,$@)" ] || \
+		{ echo "#define CONFIG_PPCHAMELEON_CLK_25" >>include/config.h ; \
+		  echo " SysClk = 25MHz" ; \
+		}
+	@[ -z "$(findstring _33,$@)" ] || \
+		{ echo "#define CONFIG_PPCHAMELEON_CLK_33" >>include/config.h ; \
+		  echo " SysClk = 33MHz" ; \
+		}
 	@./mkconfig -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave
 
 VOH405_config:	unconfig
@@ -639,16 +794,16 @@ W7OLMC_config	\
 W7OLMG_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx w7o
 
-WALNUT405_config:unconfig
+WALNUT405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx walnut405
 
-XPEDITE1K_config:unconfig
+XPEDITE1K_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx xpedite1k
 
 #########################################################################
 ## MPC824x Systems
 #########################################################################
-xtract_82xx = $(subst _ROMBOOT,,$(subst _L2,,$(subst _266MHz,,$(subst _300MHz,,$(subst _config,,$1)))))
+xtract_82xx = $(subst _BIGFLASH,,$(subst _ROMBOOT,,$(subst _L2,,$(subst _266MHz,,$(subst _300MHz,,$(subst _config,,$1))))))
 
 A3000_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x a3000
@@ -672,6 +827,9 @@ CPC45_ROMBOOT_config:	unconfig
 CU824_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x cu824
 
+debris_config: unconfig
+	@./mkconfig $(@:_config=) ppc mpc824x debris etin
+
 eXalion_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x eXalion
 
@@ -696,6 +854,9 @@ Sandpoint8240_config: unconfig
 Sandpoint8245_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x sandpoint
 
+sbc8240_config: unconfig
+	@./mkconfig $(@:_config=) ppc mpc824x sbc8240
+
 SL8245_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x sl8245
 
@@ -737,38 +898,84 @@ hymod_config:	unconfig
 IPHASE4539_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8260 iphase4539
 
-MPC8260ADS_config:	unconfig
-	@./mkconfig $(@:_config=) ppc mpc8260 mpc8260ads
+ISPAN_config		\
+ISPAN_REVB_config:	unconfig
+	@if [ "$(findstring _REVB_,$@)" ] ; then \
+		echo "#define CFG_REV_B" > include/config.h ; \
+	fi
+	@./mkconfig -a ISPAN ppc mpc8260 ispan
+
+MPC8260ADS_config	\
+MPC8260ADS_33MHz_config	\
+MPC8260ADS_40MHz_config	\
+MPC8272ADS_config	\
+PQ2FADS_config		\
+PQ2FADS-VR_config	\
+PQ2FADS-ZU_config	\
+PQ2FADS-ZU_66MHz_config	\
+	:		unconfig
+	$(if $(findstring PQ2FADS,$@), \
+	@echo "#define CONFIG_ADSTYPE CFG_PQ2FADS" > include/config.h, \
+	@echo "#define CONFIG_ADSTYPE CFG_"$(subst MPC,,$(word 1,$(subst _, ,$@))) > include/config.h)
+	$(if $(findstring MHz,$@), \
+	@echo "#define CONFIG_8260_CLKIN" $(subst MHz,,$(word 2,$(subst _, ,$@)))"000000" >> include/config.h, \
+	$(if $(findstring VR,$@), \
+	@echo "#define CONFIG_8260_CLKIN 66000000" >> include/config.h))
+	@./mkconfig -a MPC8260ADS ppc mpc8260 mpc8260ads
 
 MPC8266ADS_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8260 mpc8266ads
 
+# PM825/PM826 default configuration:  small (= 8 MB) Flash / boot from 64-bit flash
 PM825_config	\
-PM825_ROMBOOT_config: unconfig
-	@echo "#define CONFIG_PCI"	>include/config.h
-	@./mkconfig -a PM826 ppc mpc8260 pm826
-	@cd ./include ;				\
-	if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		echo "CONFIG_BOOT_ROM = y" >> config.mk ; \
-		echo "... booting from 8-bit flash" ; \
-	else \
-		echo "CONFIG_BOOT_ROM = n" >> config.mk ; \
-		echo "... booting from 64-bit flash" ; \
-	fi; \
-	echo "export CONFIG_BOOT_ROM" >> config.mk; \
-
+PM825_ROMBOOT_config	\
+PM825_BIGFLASH_config	\
+PM825_ROMBOOT_BIGFLASH_config	\
 PM826_config	\
-PM826_ROMBOOT_config: unconfig
-	@./mkconfig $(call xtract_82xx,$@) ppc mpc8260 pm826
-	@cd ./include ;				\
-	if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
-		echo "CONFIG_BOOT_ROM = y" >> config.mk ; \
-		echo "... booting from 8-bit flash" ; \
+PM826_ROMBOOT_config	\
+PM826_BIGFLASH_config	\
+PM826_ROMBOOT_BIGFLASH_config:	unconfig
+	@if [ "$(findstring PM825_,$@)" ] ; then \
+		echo "#define CONFIG_PCI"	>include/config.h ; \
+	else \
+		>include/config.h ; \
+	fi
+	@if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
+		echo "... booting from 8-bit flash" ; \
+		echo "#define CONFIG_BOOT_ROM" >>include/config.h ; \
+		echo "TEXT_BASE = 0xFF800000" >board/pm826/config.tmp ; \
+		if [ "$(findstring _BIGFLASH_,$@)" ] ; then \
+			echo "... with 32 MB Flash" ; \
+			echo "#define CONFIG_FLASH_32MB" >>include/config.h ; \
+		fi; \
 	else \
-		echo "CONFIG_BOOT_ROM = n" >> config.mk ; \
 		echo "... booting from 64-bit flash" ; \
-	fi; \
-	echo "export CONFIG_BOOT_ROM" >> config.mk; \
+		if [ "$(findstring _BIGFLASH_,$@)" ] ; then \
+			echo "... with 32 MB Flash" ; \
+			echo "#define CONFIG_FLASH_32MB" >>include/config.h ; \
+			echo "TEXT_BASE = 0x40000000" >board/pm826/config.tmp ; \
+		else \
+			echo "TEXT_BASE = 0xFF000000" >board/pm826/config.tmp ; \
+		fi; \
+	fi
+	@./mkconfig -a PM826 ppc mpc8260 pm826
+
+PM828_config	\
+PM828_PCI_config	\
+PM828_ROMBOOT_config	\
+PM828_ROMBOOT_PCI_config:	unconfig
+	@if [ -z "$(findstring _PCI_,$@)" ] ; then \
+		echo "#define CONFIG_PCI"  >>include/config.h ; \
+		echo "... with PCI enabled" ; \
+	else \
+		>include/config.h ; \
+	fi
+	@if [ "$(findstring _ROMBOOT_,$@)" ] ; then \
+		echo "... booting from 8-bit flash" ; \
+		echo "#define CONFIG_BOOT_ROM" >>include/config.h ; \
+		echo "TEXT_BASE = 0xFF800000" >board/pm826/config.tmp ; \
+	fi
+	@./mkconfig -a PM828 ppc mpc8260 pm828
 
 ppmc8260_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8260 ppmc8260
@@ -852,12 +1059,27 @@ M5282EVB_config :		unconfig
 ## MPC85xx Systems
 #########################################################################
 
-MPC8540ADS_config:      unconfig
+MPC8540ADS_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc85xx mpc8540ads
 
-MPC8560ADS_config:      unconfig
+MPC8560ADS_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc85xx mpc8560ads
 
+stxgp3_config:		unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
+
+sbc8560_config \
+sbc8560_33_config \
+sbc8560_66_config:      unconfig
+	@if [ "$(findstring _66_,$@)" ] ; then \
+		echo "#define CONFIG_PCI_66"  >>include/config.h ; \
+		echo "... 66 MHz PCI" ; \
+	else \
+		>include/config.h ; \
+		echo "... 33 MHz PCI" ; \
+	fi
+	@./mkconfig -a sbc8560 ppc mpc85xx sbc8560
+
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################
@@ -874,9 +1096,6 @@ DB64360_config:  unconfig
 DB64460_config:  unconfig
 	@./mkconfig DB64460 ppc 74xx_7xx db64460 Marvell
 
-debris_config: unconfig
-	@./mkconfig $(@:_config=) ppc mpc824x debris etin
-
 ELPPC_config: unconfig
 	@./mkconfig $(@:_config=) ppc 74xx_7xx elppc eltec
 
@@ -901,15 +1120,18 @@ ZUMA_config:	unconfig
 ## StrongARM Systems
 #########################################################################
 
-at91rm9200dk_config	:	unconfig
-	@./mkconfig $(@:_config=) arm at91rm9200 at91rm9200dk
-
-lart_config	:	unconfig
-	@./mkconfig $(@:_config=) arm sa1100 lart
+assabet_config	:	unconfig
+	@./mkconfig $(@:_config=) arm sa1100 assabet
 
 dnp1110_config	:	unconfig
 	@./mkconfig $(@:_config=) arm sa1100 dnp1110
 
+gcplus_config	:	unconfig
+	@./mkconfig $(@:_config=) arm sa1100 gcplus
+
+lart_config	:	unconfig
+	@./mkconfig $(@:_config=) arm sa1100 lart
+
 shannon_config	:	unconfig
 	@./mkconfig $(@:_config=) arm sa1100 shannon
 
@@ -919,35 +1141,76 @@ shannon_config	:	unconfig
 
 xtract_trab = $(subst _bigram,,$(subst _bigflash,,$(subst _old,,$(subst _config,,$1))))
 
-xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
+xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,,$(subst _cs_autoboot,,$(subst _config,,$1))))
 
-SX1_config :		unconfig
-	@./mkconfig $(@:_config=) arm arm925t sx1
+xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
+
+integratorcp_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs integratorcp
+
+integratorap_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs integratorap
+
+lpd7a400_config \
+lpd7a404_config:	unconfig
+	@./mkconfig $(@:_config=) arm lh7a40x lpd7a40x
+
+mx1ads_config	:	unconfig
+	@./mkconfig $(@:_config=) arm arm920t mx1ads
+
+mx1fs2_config	:	unconfig
+	@./mkconfig $(@:_config=) arm arm920t mx1fs2
 
 omap1510inn_config :	unconfig
 	@./mkconfig $(@:_config=) arm arm925t omap1510inn
 
+omap5912osk_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs omap5912osk
+
 omap1610inn_config \
 omap1610inn_cs0boot_config \
 omap1610inn_cs3boot_config \
+omap1610inn_cs_autoboot_config \
 omap1610h2_config \
 omap1610h2_cs0boot_config \
-omap1610h2_cs3boot_config :	unconfig
+omap1610h2_cs3boot_config \
+omap1610h2_cs_autoboot_config:	unconfig
 	@if [ "$(findstring _cs0boot_, $@)" ] ; then \
 		echo "#define CONFIG_CS0_BOOT" >> ./include/config.h ; \
-		echo "Configured for CS0 boot"; \
+		echo "... configured for CS0 boot"; \
+	elif [ "$(findstring _cs_autoboot_, $@)" ] ; then \
+		echo "#define CONFIG_CS_AUTOBOOT" >> ./include/config.h ; \
+		echo "... configured for CS_AUTO boot"; \
 	else \
 		echo "#define CONFIG_CS3_BOOT" >> ./include/config.h ; \
-		echo "Configured for CS3 boot"; \
+		echo "... configured for CS3 boot"; \
 	fi;
 	@./mkconfig -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn
 
+omap730p2_config \
+omap730p2_cs0boot_config \
+omap730p2_cs3boot_config :	unconfig
+	@if [ "$(findstring _cs0boot_, $@)" ] ; then \
+		echo "#define CONFIG_CS0_BOOT" >> ./include/config.h ; \
+		echo "... configured for CS0 boot"; \
+	else \
+		echo "#define CONFIG_CS3_BOOT" >> ./include/config.h ; \
+		echo "... configured for CS3 boot"; \
+	fi;
+	@./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2
+
+scb9328_config	:	unconfig
+	@./mkconfig $(@:_config=) arm arm920t scb9328
+
 smdk2400_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t smdk2400
 
 smdk2410_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t smdk2410
 
+SX1_config :		unconfig
+	@./mkconfig $(@:_config=) arm arm925t sx1
+
 # TRAB default configuration:	8 MB Flash, 32 MB RAM
 trab_config \
 trab_bigram_config \
@@ -976,6 +1239,8 @@ trab_old_config:	unconfig
 VCMA9_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t vcma9 mpl
 
+versatile_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs versatile
 
 #########################################################################
 ## S3C44B0 Systems
@@ -988,19 +1253,32 @@ B2_config	:	unconfig
 ## ARM720T Systems
 #########################################################################
 
-impa7_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm720t impa7
-
 ep7312_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm720t ep7312
 
+impa7_config	:	unconfig
+	@./mkconfig $(@:_config=) arm arm720t impa7
+
 modnet50_config :	unconfig
 	@./mkconfig $(@:_config=) arm arm720t modnet50
 
+evb4510_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm720t evb4510
+
+#########################################################################
+## AT91RM9200 Systems
+#########################################################################
+
+at91rm9200dk_config	:	unconfig
+	@./mkconfig $(@:_config=) arm at91rm9200 at91rm9200dk
+
 #########################################################################
 ## XScale Systems
 #########################################################################
 
+cerf250_config :	unconfig
+	@./mkconfig $(@:_config=) arm pxa cerf250
+
 cradle_config	:	unconfig
 	@./mkconfig $(@:_config=) arm pxa cradle
 
@@ -1022,6 +1300,12 @@ logodl_config	:	unconfig
 wepep250_config	:	unconfig
 	@./mkconfig $(@:_config=) arm pxa wepep250
 
+xm250_config	:	unconfig
+	@./mkconfig $(@:_config=) arm pxa xm250
+
+xsengine_config :	unconfig
+	@./mkconfig $(@:_config=) arm pxa xsengine
+
 #========================================================================
 # i386
 #========================================================================
@@ -1068,6 +1352,24 @@ incaip_config: unconfig
 tb0229_config: unconfig
 	@./mkconfig $(@:_config=) mips mips tb0229
 
+#########################################################################
+## MIPS32 AU1X00
+#########################################################################
+dbau1000_config		: 	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_DBAU1000 1" >>include/config.h
+	@./mkconfig -a dbau1x00 mips mips dbau1x00
+
+dbau1100_config		: 	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_DBAU1100 1" >>include/config.h
+	@./mkconfig -a dbau1x00 mips mips dbau1x00
+
+dbau1500_config		: 	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_DBAU1500 1" >>include/config.h
+	@./mkconfig -a dbau1x00 mips mips dbau1x00
+
 #########################################################################
 ## MIPS64 5Kc
 #########################################################################
@@ -1123,24 +1425,35 @@ DK1S10_config:	unconfig
 		}
 	@./mkconfig -a DK1S10 nios nios dk1s10 altera
 
+ADNPESC1_DNPEVA2_base_32_config	\
+ADNPESC1_base_32_config		\
+ADNPESC1_config: unconfig
+	@ >include/config.h
+	@[ -z "$(findstring _DNPEVA2,$@)" ] || \
+		{ echo "#define CONFIG_DNPEVA2 1" >>include/config.h ; \
+		  echo "... DNP/EVA2 configuration" ; \
+		}
+	@[ -z "$(findstring _base_32,$@)" ] || \
+		{ echo "#define CONFIG_NIOS_BASE_32 1" >>include/config.h ; \
+		  echo "... NIOS 'base_32' configuration" ; \
+		}
+	@[ -z "$(findstring ADNPESC1_config,$@)" ] || \
+		{ echo "#define CONFIG_NIOS_BASE_32 1" >>include/config.h ; \
+		  echo "... NIOS 'base_32' configuration (DEFAULT)" ; \
+		}
+	@./mkconfig -a ADNPESC1 nios nios adnpesc1 ssv
 
+
+#========================================================================
+# MicroBlaze
+#========================================================================
 #########################################################################
-## MIPS32 AU1X00
+## Microblaze
 #########################################################################
-dbau1000_config		: 	unconfig
+suzaku_config:	unconfig
 	@ >include/config.h
-	@echo "#define CONFIG_DBAU1000 1" >>include/config.h
-	@./mkconfig -a dbau1x00 mips mips dbau1x00
-
-dbau1100_config		: 	unconfig
-	@ >include/config.h
-	@echo "#define CONFIG_DBAU1100 1" >>include/config.h
-	@./mkconfig -a dbau1x00 mips mips dbau1x00
-
-dbau1500_config		: 	unconfig
-	@ >include/config.h
-	@echo "#define CONFIG_DBAU1500 1" >>include/config.h
-	@./mkconfig -a dbau1x00 mips mips dbau1x00
+	@echo "#define CONFIG_SUZAKU 1" >> include/config.h
+	@./mkconfig -a $(@:_config=) microblaze microblaze suzaku AtmarkTechno
 
 #########################################################################
 #########################################################################
@@ -1153,19 +1466,19 @@ clean:
 	rm -f examples/hello_world examples/timer \
 	      examples/eepro100_eeprom examples/sched \
 	      examples/mem_to_mem_idma2intr examples/82559_eeprom
-
 	rm -f tools/img2srec tools/mkimage tools/envcrc tools/gen_eth_addr
+	rm -f tools/mpc86x_clk
 	rm -f tools/easylogo/easylogo tools/bmp_logo
 	rm -f tools/gdb/astest tools/gdb/gdbcont tools/gdb/gdbsend
 	rm -f tools/env/fw_printenv tools/env/fw_setenv
 	rm -f board/cray/L1/bootscript.c board/cray/L1/bootscript.image
-	rm -f board/trab/trab_fkt board/*/config.tmp
+	rm -f board/trab/trab_fkt
 
 clobber:	clean
-	find . -type f \
-		\( -name .depend -o -name '*.srec' -o -name '*.bin' \) \
-		-print \
-		| xargs rm -f
+	find . -type f \( -name .depend \
+		-o -name '*.srec' -o -name '*.bin' -o -name u-boot.img \) \
+		-print0 \
+		| xargs -0 rm -f
 	rm -f $(OBJS) *.bak tags TAGS
 	rm -fr *.*~
 	rm -f u-boot u-boot.map $(ALL)

README

@@ -240,57 +240,69 @@ The following options need to be configured:
 		CONFIG_ARM7
 		CONFIG_PXA250
 
+		MicroBlaze based CPUs:
+		----------------------
+		CONFIG_MICROBLAZE
+
 
 - Board Type:	Define exactly one of
 
 		PowerPC based boards:
 		---------------------
 
-		CONFIG_ADCIOP,	   CONFIG_ICU862      CONFIG_RPXsuper,
-		CONFIG_ADS860,	   CONFIG_IP860,      CONFIG_SM850,
-		CONFIG_AMX860,	   CONFIG_IPHASE4539, CONFIG_SPD823TS,
-		CONFIG_AR405,	   CONFIG_IVML24,     CONFIG_SXNI855T,
-		CONFIG_BAB7xx,	   CONFIG_IVML24_128, CONFIG_Sandpoint8240,
-		CONFIG_CANBT,	   CONFIG_IVML24_256, CONFIG_Sandpoint8245,
-		CONFIG_CCM,	   CONFIG_IVMS8,      CONFIG_TQM823L,
-		CONFIG_CPCI405,	   CONFIG_IVMS8_128,  CONFIG_TQM850L,
-		CONFIG_CPCI4052,   CONFIG_IVMS8_256,  CONFIG_TQM855L,
-		CONFIG_CPCIISER4,  CONFIG_LANTEC,     CONFIG_TQM860L,
-		CONFIG_CPU86,	   CONFIG_MBX,	      CONFIG_TQM8260,
-		CONFIG_CRAYL1,	   CONFIG_MBX860T,    CONFIG_TTTech,
-		CONFIG_CU824,	   CONFIG_MHPC,	      CONFIG_UTX8245,
-		CONFIG_DASA_SIM,   CONFIG_MIP405,     CONFIG_W7OLMC,
-		CONFIG_DU405,	   CONFIG_MOUSSE,     CONFIG_W7OLMG,
-		CONFIG_ELPPC,	   CONFIG_MPC8260ADS, CONFIG_WALNUT405,
-		CONFIG_ERIC,	   CONFIG_MUSENKI,    CONFIG_ZUMA,
-		CONFIG_ESTEEM192E, CONFIG_MVS1,	      CONFIG_c2mon,
-		CONFIG_ETX094,	   CONFIG_NX823,      CONFIG_cogent_mpc8260,
-		CONFIG_EVB64260,   CONFIG_OCRTC,      CONFIG_cogent_mpc8xx,
-		CONFIG_FADS823,	   CONFIG_ORSG,	      CONFIG_ep8260,
-		CONFIG_FADS850SAR, CONFIG_OXC,	      CONFIG_gw8260,
-		CONFIG_FADS860T,   CONFIG_PCI405,     CONFIG_hermes,
-		CONFIG_FLAGADM,	   CONFIG_PCIPPC2,    CONFIG_hymod,
-		CONFIG_FPS850L,	   CONFIG_PCIPPC6,    CONFIG_lwmon,
-		CONFIG_GEN860T,	   CONFIG_PIP405,     CONFIG_pcu_e,
-		CONFIG_GENIETV,	   CONFIG_PM826,      CONFIG_ppmc8260,
-		CONFIG_GTH,	   CONFIG_RPXClassic, CONFIG_rsdproto,
-		CONFIG_IAD210,	   CONFIG_RPXlite,    CONFIG_sbc8260,
-		CONFIG_EBONY,	   CONFIG_sacsng,     CONFIG_FPS860L,
-		CONFIG_V37,	   CONFIG_ELPT860,    CONFIG_CMI,
-		CONFIG_NETVIA,	   CONFIG_RBC823,     CONFIG_ZPC1900,
-		CONFIG_MPC8540ADS, CONFIG_MPC8560ADS, CONFIG_QS850,
-		CONFIG_QS823,	   CONFIG_QS860T,     CONFIG_DB64360,
-		CONFIG_DB64460,	   CONFIG_DUET_ADS
+		CONFIG_ADCIOP		CONFIG_GEN860T		CONFIG_PCI405
+		CONFIG_ADS860		CONFIG_GENIETV		CONFIG_PCIPPC2
+		CONFIG_AMX860		CONFIG_GTH		CONFIG_PCIPPC6
+		CONFIG_AR405		CONFIG_gw8260		CONFIG_pcu_e
+		CONFIG_BAB7xx		CONFIG_hermes		CONFIG_PIP405
+		CONFIG_c2mon		CONFIG_hymod		CONFIG_PM826
+		CONFIG_CANBT		CONFIG_IAD210		CONFIG_ppmc8260
+		CONFIG_CCM		CONFIG_ICU862		CONFIG_QS823
+		CONFIG_CMI		CONFIG_IP860		CONFIG_QS850
+		CONFIG_cogent_mpc8260	CONFIG_IPHASE4539	CONFIG_QS860T
+		CONFIG_cogent_mpc8xx	CONFIG_IVML24		CONFIG_RBC823
+		CONFIG_CPCI405		CONFIG_IVML24_128	CONFIG_RPXClassic
+		CONFIG_CPCI4052		CONFIG_IVML24_256	CONFIG_RPXlite
+		CONFIG_CPCIISER4	CONFIG_IVMS8		CONFIG_RPXsuper
+		CONFIG_CPU86		CONFIG_IVMS8_128	CONFIG_rsdproto
+		CONFIG_CRAYL1		CONFIG_IVMS8_256	CONFIG_sacsng
+		CONFIG_CSB272		CONFIG_JSE		CONFIG_Sandpoint8240
+		CONFIG_CU824		CONFIG_LANTEC		CONFIG_Sandpoint8245
+		CONFIG_DASA_SIM		CONFIG_lwmon		CONFIG_sbc8260
+		CONFIG_DB64360		CONFIG_MBX		CONFIG_sbc8560
+		CONFIG_DB64460		CONFIG_MBX860T		CONFIG_SM850
+		CONFIG_DU405		CONFIG_MHPC		CONFIG_SPD823TS
+		CONFIG_DUET_ADS		CONFIG_MIP405		CONFIG_STXGP3
+		CONFIG_EBONY		CONFIG_MOUSSE		CONFIG_SXNI855T
+		CONFIG_ELPPC		CONFIG_MPC8260ADS	CONFIG_TQM823L
+		CONFIG_ELPT860		CONFIG_MPC8540ADS	CONFIG_TQM8260
+		CONFIG_ep8260		CONFIG_MPC8560ADS	CONFIG_TQM850L
+		CONFIG_ERIC		CONFIG_MUSENKI		CONFIG_TQM855L
+		CONFIG_ESTEEM192E	CONFIG_MVS1		CONFIG_TQM860L
+		CONFIG_ETX094		CONFIG_NETPHONE		CONFIG_TTTech
+		CONFIG_EVB64260		CONFIG_NETTA		CONFIG_UTX8245
+		CONFIG_FADS823		CONFIG_NETVIA		CONFIG_V37
+		CONFIG_FADS850SAR	CONFIG_NX823		CONFIG_W7OLMC
+		CONFIG_FADS860T		CONFIG_OCRTC		CONFIG_W7OLMG
+		CONFIG_FLAGADM		CONFIG_ORSG		CONFIG_WALNUT405
+		CONFIG_FPS850L		CONFIG_OXC		CONFIG_ZPC1900
+		CONFIG_FPS860L					CONFIG_ZUMA
 
 		ARM based boards:
 		-----------------
 
-		CONFIG_HHP_CRADLE,  CONFIG_DNP1110,	CONFIG_EP7312,
-		CONFIG_IMPA7,	    CONFIG_LART,	CONFIG_LUBBOCK,
-		CONFIG_INNOVATOROMAP1510,      CONFIG_INNOVATOROMAP1610,
-		CONFIG_H2_OMAP1610, CONFIG_SHANNON,	CONFIG_SMDK2400,
-		CONFIG_SMDK2410,    CONFIG_TRAB,	CONFIG_VCMA9,
-		CONFIG_AT91RM9200DK
+		CONFIG_AT91RM9200DK,		CONFIG_CERF250,		CONFIG_DNP1110,
+		CONFIG_EP7312,			CONFIG_H2_OMAP1610,	CONFIG_HHP_CRADLE,
+		CONFIG_IMPA7,		CONFIG_INNOVATOROMAP1510,	CONFIG_INNOVATOROMAP1610,
+		CONFIG_LART,			CONFIG_LPD7A400		CONFIG_LUBBOCK,
+		CONFIG_OSK_OMAP5912,		CONFIG_SHANNON,		CONFIG_P2_OMAP730,
+		CONFIG_SMDK2400,		CONFIG_SMDK2410,	CONFIG_TRAB,
+		CONFIG_VCMA9
+
+		MicroBlaze based boards:
+		------------------------
+
+		CONFIG_SUZAKU
 
 
 - CPU Module Type: (if CONFIG_COGENT is defined)
@@ -320,7 +332,7 @@ The following options need to be configured:
 			CFG_8260ADS	- original MPC8260ADS
 			CFG_8266ADS	- MPC8266ADS
 			CFG_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
-
+			CFG_8272ADS	- MPC8272ADS
 
 - MPC824X Family Member (if CONFIG_MPC824X is defined)
 		Define exactly one of
@@ -368,6 +380,27 @@ The following options need to be configured:
 		expect it to be in bytes, others in MB.
 		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
 
+- Serial Ports:
+		CFG_PL010_SERIAL
+
+		Define this if you want support for Amba PrimeCell PL010 UARTs.
+
+		CFG_PL011_SERIAL
+
+		Define this if you want support for Amba PrimeCell PL011 UARTs.
+
+		CONFIG_PL011_CLOCK
+
+		If you have Amba PrimeCell PL011 UARTs, set this variable to
+		the clock speed of the UARTs.
+
+		CONFIG_PL01x_PORTS
+
+		If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
+		define this to a list of base addresses for each (supported)
+		port. See e.g. include/configs/versatile.h
+
+
 - Console Interface:
 		Depending on board, define exactly one serial port
 		(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
@@ -441,8 +474,8 @@ The following options need to be configured:
 		(RTS/CTS) and UART's built-in FIFO. Set the number of
 		bytes the interrupt driven input buffer should have.
 
-		Set to 0 to disable this feature (this is the default).
-		This will also disable hardware handshake.
+		Leave undefined to disable this feature, including
+		disable the buffer and hardware handshake.
 
 - Console UART Number:
 		CONFIG_UART1_CONSOLE
@@ -529,22 +562,23 @@ The following options need to be configured:
 		CFG_CMD_ASKENV	* ask for env variable
 		CFG_CMD_AUTOSCRIPT Autoscript Support
 		CFG_CMD_BDI	  bdinfo
-		CFG_CMD_BEDBUG	  Include BedBug Debugger
+		CFG_CMD_BEDBUG	* Include BedBug Debugger
 		CFG_CMD_BMP	* BMP support
+		CFG_CMD_BSP	* Board specific commands
 		CFG_CMD_BOOTD	  bootd
-		CFG_CMD_CACHE	  icache, dcache
+		CFG_CMD_CACHE	* icache, dcache
 		CFG_CMD_CONSOLE	  coninfo
 		CFG_CMD_DATE	* support for RTC, date/time...
-		CFG_CMD_DHCP	  DHCP support
+		CFG_CMD_DHCP	* DHCP support
 		CFG_CMD_DIAG	* Diagnostics
 		CFG_CMD_DOC	* Disk-On-Chip Support
-		CFG_CMD_DTT	  Digital Therm and Thermostat
+		CFG_CMD_DTT	* Digital Therm and Thermostat
 		CFG_CMD_ECHO	* echo arguments
 		CFG_CMD_EEPROM	* EEPROM read/write support
-		CFG_CMD_ELF	  bootelf, bootvx
+		CFG_CMD_ELF	* bootelf, bootvx
 		CFG_CMD_ENV	  saveenv
 		CFG_CMD_FDC	* Floppy Disk Support
-		CFG_CMD_FAT	  FAT partition support
+		CFG_CMD_FAT	* FAT partition support
 		CFG_CMD_FDOS	* Dos diskette Support
 		CFG_CMD_FLASH	  flinfo, erase, protect
 		CFG_CMD_FPGA	  FPGA device initialization support
@@ -555,16 +589,16 @@ The following options need to be configured:
 		CFG_CMD_IMLS	  List all found images
 		CFG_CMD_IMMAP	* IMMR dump support
 		CFG_CMD_IRQ	* irqinfo
-		CFG_CMD_ITEST	* Integer/string test of 2 values
+		CFG_CMD_ITEST	  Integer/string test of 2 values
 		CFG_CMD_JFFS2	* JFFS2 Support
 		CFG_CMD_KGDB	* kgdb
 		CFG_CMD_LOADB	  loadb
 		CFG_CMD_LOADS	  loads
 		CFG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
-				  loop, mtest
+				  loop, loopw, mtest
 		CFG_CMD_MISC	  Misc functions like sleep etc
-		CFG_CMD_MMC	  MMC memory mapped support
-		CFG_CMD_MII	  MII utility commands
+		CFG_CMD_MMC	* MMC memory mapped support
+		CFG_CMD_MII	* MII utility commands
 		CFG_CMD_NAND	* NAND support
 		CFG_CMD_NET	  bootp, tftpboot, rarpboot
 		CFG_CMD_PCI	* pciinfo
@@ -573,7 +607,7 @@ The following options need to be configured:
 		CFG_CMD_PORTIO	* Port I/O
 		CFG_CMD_REGINFO * Register dump
 		CFG_CMD_RUN	  run command in env variable
-		CFG_CMD_SAVES	  save S record dump
+		CFG_CMD_SAVES	* save S record dump
 		CFG_CMD_SCSI	* SCSI Support
 		CFG_CMD_SDRAM	* print SDRAM configuration information
 		CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
@@ -581,16 +615,17 @@ The following options need to be configured:
 		CFG_CMD_USB	* USB support
 		CFG_CMD_VFD	* VFD support (TRAB)
 		CFG_CMD_BSP	* Board SPecific functions
+		CFG_CMD_CDP	* Cisco Discover Protocol support
 		-----------------------------------------------
 		CFG_CMD_ALL	all
 
-		CFG_CMD_DFL	Default configuration; at the moment
+		CONFIG_CMD_DFL	Default configuration; at the moment
 				this is includes all commands, except
 				the ones marked with "*" in the list
 				above.
 
 		If you don't define CONFIG_COMMANDS it defaults to
-		CFG_CMD_DFL in include/cmd_confdefs.h. A board can
+		CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
 		override the default settings in the respective
 		include file.
 
@@ -640,6 +675,7 @@ The following options need to be configured:
 		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
 		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
 		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
+		CONFIG_RTC_MAX6900	- use Maxim, Inc. MAX6900 RTC
 
 		Note that if the RTC uses I2C, then the I2C interface
 		must also be configured. See I2C Support, below.
@@ -660,16 +696,31 @@ The following options need to be configured:
 		one partition type as well.
 
 - IDE Reset method:
-		CONFIG_IDE_RESET_ROUTINE
+		CONFIG_IDE_RESET_ROUTINE - this is defined in several
+		board configurations files but used nowhere!
 
-		Set this to define that instead of a reset Pin, the
-		routine ide_set_reset(int idereset) will be used.
+		CONFIG_IDE_RESET - is this is defined, IDE Reset will
+		be performed by calling the function
+			ide_set_reset(int reset)
+		which has to be defined in a board specific file
 
 - ATAPI Support:
 		CONFIG_ATAPI
 
 		Set this to enable ATAPI support.
 
+- LBA48 Support
+		CONFIG_LBA48
+
+		Set this to enable support for disks larger than 137GB
+		Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
+		Whithout these , LBA48 support uses 32bit variables and will 'only'
+		support disks up to 2.1TB.
+
+		CFG_64BIT_LBA:
+			When enabled, makes the IDE subsystem use 64bit sector addresses.
+			Default is 32bit.
+
 - SCSI Support:
 		At the moment only there is only support for the
 		SYM53C8XX SCSI controller; define
@@ -714,9 +765,23 @@ The following options need to be configured:
 			CONFIG_LAN91C96_USE_32_BIT
 			Define this to enable 32 bit addressing
 
+		CONFIG_DRIVER_SMC91111
+		Support for SMSC's LAN91C111 chip
+
+			CONFIG_SMC91111_BASE
+			Define this to hold the physical address
+			of the device (I/O space)
+
+			CONFIG_SMC_USE_32_BIT
+			Define this if data bus is 32 bits
+
+			CONFIG_SMC_USE_IOFUNCS
+			Define this to use i/o functions instead of macros
+			(some hardware wont work with macros)
+
 - USB Support:
 		At the moment only the UHCI host controller is
-		supported (PIP405, MIP405); define
+		supported (PIP405, MIP405, MPC5200); define
 		CONFIG_USB_UHCI to enable it.
 		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
 		end define CONFIG_USB_STORAGE to enable the USB
@@ -724,6 +789,13 @@ The following options need to be configured:
 		Note:
 		Supported are USB Keyboards and USB Floppy drives
 		(TEAC FD-05PUB).
+		MPC5200 USB requires additional defines:
+			CONFIG_USB_CLOCK
+				for 528 MHz Clock: 0x0001bbbb
+			CONFIG_USB_CONFIG
+				for differential drivers: 0x00001000
+				for single ended drivers: 0x00005000
+
 
 - MMC Support:
 		The MMC controller on the Intel PXA is supported. To
@@ -733,6 +805,24 @@ The following options need to be configured:
 		enabled with CFG_CMD_MMC. The MMC driver also works with
 		the FAT fs. This is enabled with CFG_CMD_FAT.
 
+- Journaling Flash filesystem support:
+		CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
+		CONFIG_JFFS2_NAND_DEV
+		Define these for a default partition on a NAND device
+
+		CFG_JFFS2_FIRST_SECTOR,
+		CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
+		Define these for a default partition on a NOR device
+
+		CFG_JFFS_CUSTOM_PART
+		Define this to create an own partition. You have to provide a
+		function struct part_info* jffs2_part_info(int part_num)
+
+		If you define only one JFFS2 partition you may also want to
+		#define CFG_JFFS_SINGLE_PART    1
+		to disable the command chpart. This is the default when you
+		have not defined a custom partition
+
 - Keyboard Support:
 		CONFIG_ISA_KEYBOARD
 
@@ -756,17 +846,30 @@ The following options need to be configured:
 		Enable Chips & Technologies 69000 Video chip
 
 		CONFIG_VIDEO_SMI_LYNXEM
-		Enable Silicon Motion SMI 712/710/810 Video chip
-		Videomode are selected via environment 'videomode' with
-		standard LiLo mode numbers.
-		Following modes are supported  (* is default):
+		Enable Silicon Motion SMI 712/710/810 Video chip. The
+		video output is selected via environment 'videoout'
+		(1 = LCD and 2 = CRT). If videoout is undefined, CRT is
+		assumed.
 
-			    800x600  1024x768  1280x1024
-	      256  (8bit)     303*	305	  307
-	    65536 (16bit)     314	317	  31a
-	16,7 Mill (24bit)     315	318	  31b
+		For the CT69000 and SMI_LYNXEM drivers, videomode is
+		selected via environment 'videomode'. Two diferent ways
+		are possible:
+		- "videomode=num"   'num' is a standard LiLo mode numbers.
+		Following standard modes are supported	(* is default):
+
+		      Colors	640x480 800x600 1024x768 1152x864 1280x1024
+		-------------+---------------------------------------------
+		      8 bits |	0x301*	0x303	 0x305	  0x161	    0x307
+		     15 bits |	0x310	0x313	 0x316	  0x162	    0x319
+		     16 bits |	0x311	0x314	 0x317	  0x163	    0x31A
+		     24 bits |	0x312	0x315	 0x318	    ?	    0x31B
+		-------------+---------------------------------------------
 		(i.e. setenv videomode 317; saveenv; reset;)
 
+		- "videomode=bootargs" all the video parameters are parsed
+		from the bootargs. (See drivers/videomodes.c)
+
+
 		CONFIG_VIDEO_SED13806
 		Enable Epson SED13806 driver. This driver supports 8bpp
 		and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
@@ -833,7 +936,7 @@ The following options need to be configured:
 		If this option is set, the environment is checked for
 		a variable "splashimage". If found, the usual display
 		of logo, copyright and system information on the LCD
-		is supressed and the BMP image at the address
+		is suppressed and the BMP image at the address
 		specified in "splashimage" is loaded instead. The
 		console is redirected to the "nulldev", too. This
 		allows for a "silent" boot where a splash screen is
@@ -850,6 +953,32 @@ The following options need to be configured:
 		the malloc area (as defined by CFG_MALLOC_LEN) should
 		be at least 4MB.
 
+- MII/PHY support:
+		CONFIG_PHY_ADDR
+
+		The address of PHY on MII bus.
+
+		CONFIG_PHY_CLOCK_FREQ (ppc4xx)
+
+		The clock frequency of the MII bus
+
+		CONFIG_PHY_GIGE
+
+		If this option is set, support for speed/duplex
+		detection of Gigabit PHY is included.
+
+		CONFIG_PHY_RESET_DELAY
+
+		Some PHY like Intel LXT971A need extra delay after
+		reset before any MII register access is possible.
+		For such PHY, set this option to the usec delay
+		required. (minimum 300usec for LXT971A)
+
+		CONFIG_PHY_CMD_DELAY (ppc4xx)
+
+		Some PHY like Intel LXT971A need extra delay after
+		command issued before MII status register can be read
+
 - Ethernet address:
 		CONFIG_ETHADDR
 		CONFIG_ETH2ADDR
@@ -914,6 +1043,48 @@ The following options need to be configured:
 		environment variable is passed as option 12 to
 		the DHCP server.
 
+ - CDP Options:
+		CONFIG_CDP_DEVICE_ID
+
+		The device id used in CDP trigger frames.
+
+		CONFIG_CDP_DEVICE_ID_PREFIX
+
+		A two character string which is prefixed to the MAC address
+		of the device.
+
+		CONFIG_CDP_PORT_ID
+
+		A printf format string which contains the ascii name of
+		the port. Normally is set to "eth%d" which sets
+		eth0 for the first ethernet, eth1 for the second etc.
+
+		CONFIG_CDP_CAPABILITIES
+
+		A 32bit integer which indicates the device capabilities;
+		0x00000010 for a normal host which does not forwards.
+
+		CONFIG_CDP_VERSION
+
+		An ascii string containing the version of the software.
+
+		CONFIG_CDP_PLATFORM
+
+		An ascii string containing the name of the platform.
+
+		CONFIG_CDP_TRIGGER
+
+		A 32bit integer sent on the trigger.
+
+		CONFIG_CDP_POWER_CONSUMPTION
+
+		A 16bit integer containing the power consumption of the
+		device in .1 of milliwatts.
+
+		CONFIG_CDP_APPLIANCE_VLAN_TYPE
+
+		A byte containing the id of the VLAN.
+
 - Status LED:	CONFIG_STATUS_LED
 
 		Several configurations allow to display the current
@@ -1042,6 +1213,12 @@ The following options need to be configured:
 		custom i2c_init_board() routine in boards/xxx/board.c
 		is run early in the boot sequence.
 
+		CONFIG_I2CFAST (PPC405GP|PPC405EP only)
+
+		This option enables configuration of bi_iic_fast[] flags
+		in u-boot bd_info structure based on u-boot environment
+		variable "i2cfast". (see also i2cfast)
+
 - SPI Support:	CONFIG_SPI
 
 		Enables SPI driver (so far only tested with
@@ -1196,6 +1373,10 @@ The following options need to be configured:
 		default value of 5 is used.
 
 - Command Interpreter:
+		CFG_AUTO_COMPLETE
+
+		Enable auto completion of commands using TAB.
+
 		CFG_HUSH_PARSER
 
 		Define this variable to enable the "hush" shell (from
@@ -1660,6 +1841,17 @@ to save the current settings.
 	  The length in bytes of the EEPROM memory array address.  Note
 	  that this is NOT the chip address length!
 
+	- CFG_I2C_EEPROM_ADDR_OVERFLOW:
+	  EEPROM chips that implement "address overflow" are ones
+	  like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+	  address and the extra bits end up in the "chip address" bit
+	  slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+	  byte chips.
+
+	  Note that we consider the length of the address field to
+	  still be one byte because the extra address bits are hidden
+	  in the chip address.
+
 	- CFG_EEPROM_SIZE:
 	  The size in bytes of the EEPROM device.
 
@@ -1677,6 +1869,16 @@ to save the current settings.
 	  environment area within the total memory of your DataFlash placed
 	  at the specified address.
 
+- CFG_ENV_IS_IN_NAND:
+
+	Define this if you have a NAND device which you want to use
+	for the environment.
+
+	- CFG_ENV_OFFSET:
+	- CFG_ENV_SIZE:
+
+	  These two #defines specify the offset and size of the environment
+	  area within the first NAND device.
 
 - CFG_SPI_INIT_OFFSET
 
@@ -1713,6 +1915,13 @@ use the "saveenv" command to store a valid environment.
 - CFG_FAULT_MII_ADDR:
 		MII address of the PHY to check for the Ethernet link state.
 
+- CFG_64BIT_VSPRINTF:
+		Makes vsprintf (and all *printf functions) support printing
+		of 64bit values by using the L quantifier
+
+- CFG_64BIT_STRTOUL:
+		Adds simple_strtoull that returns a 64bit value
+
 Low Level (hardware related) configuration options:
 ---------------------------------------------------
 
@@ -1854,6 +2063,40 @@ Low Level (hardware related) configuration options:
   CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
 		Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
 
+- CONFIG_ETHER_ON_FEC[12]
+		Define to enable FEC[12] on a 8xx series processor.
+
+- CONFIG_FEC[12]_PHY
+		Define to the hardcoded PHY address which corresponds
+		to the given FEC; i. e.
+			#define CONFIG_FEC1_PHY 4
+		means that the PHY with address 4 is connected to FEC1
+
+		When set to -1, means to probe for first available.
+
+- CONFIG_FEC[12]_PHY_NORXERR
+		The PHY does not have a RXERR line (RMII only).
+		(so program the FEC to ignore it).
+
+- CONFIG_RMII
+		Enable RMII mode for all FECs.
+		Note that this is a global option, we can't
+		have one FEC in standard MII mode and another in RMII mode.
+
+- CONFIG_CRC32_VERIFY
+		Add a verify option to the crc32 command.
+		The syntax is:
+
+		=> crc32 -v <address> <count> <crc32>
+
+		Where address/count indicate a memory area
+		and crc32 is the correct crc32 which the
+		area should have.
+
+- CONFIG_LOOPW
+		Add the "loopw" memory command. This only takes effect if
+		the memory commands are activated globally (CFG_CMD_MEM).
+
 Building the Software:
 ======================
 
@@ -1881,54 +2124,43 @@ is done by typing:
 where "NAME_config" is the name of one of the existing
 configurations; the following names are supported:
 
-    ADCIOP_config	  GTH_config		TQM850L_config
-    ADS860_config	  IP860_config		TQM855L_config
-    AR405_config	  IVML24_config		TQM860L_config
-    CANBT_config	  IVMS8_config		WALNUT405_config
-    CPCI405_config	  LANTEC_config		cogent_common_config
-    CPCIISER4_config	  MBX_config		cogent_mpc8260_config
-    CU824_config	  MBX860T_config	cogent_mpc8xx_config
-    ESTEEM192E_config	  RPXlite_config	hermes_config
-    ETX094_config	  RPXsuper_config	hymod_config
-    FADS823_config	  SM850_config		lwmon_config
-    FADS850SAR_config	  SPD823TS_config	pcu_e_config
-    FADS860T_config	  SXNI855T_config	rsdproto_config
-    FPS850L_config	  Sandpoint8240_config	sbc8260_config
-    GENIETV_config	  TQM823L_config	PIP405_config
-    GEN860T_config	  EBONY_config		FPS860L_config
-    ELPT860_config	  cmi_mpc5xx_config	NETVIA_config
-    at91rm9200dk_config	  omap1510inn_config	MPC8260ADS_config
-    omap1610inn_config	  ZPC1900_config	MPC8540ADS_config
-    MPC8560ADS_config	  QS850_config		QS823_config
-    QS860T_config	  DUET_ADS_config	omap1610h2_config
+	ADCIOP_config		FPS860L_config		omap730p2_config
+	ADS860_config		GEN860T_config		pcu_e_config
+	AR405_config		GENIETV_config		PIP405_config
+	at91rm9200dk_config	GTH_config		QS823_config
+	CANBT_config		hermes_config		QS850_config
+	cmi_mpc5xx_config	hymod_config		QS860T_config
+	cogent_common_config	IP860_config		RPXlite_config
+	cogent_mpc8260_config	IVML24_config		RPXlite_DW_config
+	cogent_mpc8xx_config	IVMS8_config		RPXsuper_config
+	CPCI405_config		JSE_config		rsdproto_config
+	CPCIISER4_config	LANTEC_config		Sandpoint8240_config
+	csb272_config		lwmon_config		sbc8260_config
+	CU824_config		MBX860T_config		sbc8560_33_config
+	DUET_ADS_config		MBX_config		sbc8560_66_config
+	EBONY_config		MPC8260ADS_config	SM850_config
+	ELPT860_config		MPC8540ADS_config	SPD823TS_config
+	ESTEEM192E_config	MPC8560ADS_config	stxgp3_config
+	ETX094_config		NETVIA_config		SXNI855T_config
+	FADS823_config		omap1510inn_config	TQM823L_config
+	FADS850SAR_config	omap1610h2_config	TQM850L_config
+	FADS860T_config		omap1610inn_config	TQM855L_config
+	FPS850L_config		omap5912osk_config	TQM860L_config
+							WALNUT405_config
+							ZPC1900_config
 
-Note: for some board special configuration names may exist; check  if
-      additional  information is available from the board vendor; for
-      instance, the TQM8xxL systems run normally at 50 MHz and use  a
-      SCC  for	10baseT	 ethernet; there are also systems with 80 MHz
-      CPU clock, and an optional Fast Ethernet	module	is  available
-      for  CPU's  with FEC. You can select such additional "features"
+Note: for some board special configuration names may exist; check if
+      additional information is available from the board vendor; for
+      instance, the TQM823L systems are available without (standard)
+      or with LCD support. You can select such additional "features"
       when chosing the configuration, i. e.
 
-      make TQM860L_config
-	- will configure for a plain TQM860L, i. e. 50MHz, no FEC
-
-      make TQM860L_FEC_config
-	- will configure for a TQM860L at 50MHz with FEC for ethernet
-
-      make TQM860L_80MHz_config
-	- will configure for a TQM860L at 80 MHz, with normal 10baseT
-	  interface
-
-      make TQM860L_FEC_80MHz_config
-	- will configure for a TQM860L at 80 MHz with FEC for ethernet
+      make TQM823L_config
+	- will configure for a plain TQM823L, i. e. no LCD support
 
       make TQM823L_LCD_config
 	- will configure for a TQM823L with U-Boot console on LCD
 
-      make TQM823L_LCD_80MHz_config
-	- will configure for a TQM823L at 80 MHz with U-Boot console on LCD
-
       etc.
 
 
@@ -2037,6 +2269,7 @@ iminfo	- print header information for application image
 coninfo - print console devices and informations
 ide	- IDE sub-system
 loop	- infinite loop on address range
+loopw	- infinite write loop on address range
 mtest	- simple RAM test
 icache	- enable or disable instruction cache
 dcache	- enable or disable data cache
@@ -2096,6 +2329,12 @@ Some configuration options can be set using Environment Variables:
 		  This can be used to load and uncompress arbitrary
 		  data.
 
+  i2cfast	- (PPC405GP|PPC405EP only)
+		  if set to 'y' configures Linux I2C driver for fast
+		  mode (400kHZ). This environment variable is used in
+		  initialization code. So, for changes to be effective
+		  it must be saved and board must be reset.
+
   initrd_high	- restrict positioning of initrd images:
 		  If this variable is not set, initrd images will be
 		  copied to the highest possible address in RAM; this
@@ -2140,6 +2379,29 @@ Some configuration options can be set using Environment Variables:
 
   bootstopkey	- see CONFIG_AUTOBOOT_STOP_STR
 
+  ethprime	- When CONFIG_NET_MULTI is enabled controls which
+		  interface is used first.
+
+  ethact	- When CONFIG_NET_MULTI is enabled controls which
+		  interface is currently active. For example you
+		  can do the following
+
+		  => setenv ethact FEC ETHERNET
+		  => ping 192.168.0.1 # traffic sent on FEC ETHERNET
+		  => setenv ethact SCC ETHERNET
+		  => ping 10.0.0.1 # traffic sent on SCC ETHERNET
+
+   netretry	- When set to "no" each network operation will
+		  either succeed or fail without retrying.
+		  When set to "once" the network operation will
+		  fail when all the available network interfaces
+		  are tried once without success.
+		  Useful on scripts which control the retry operation
+		  themselves.
+
+   vlan		- When set to a value < 4095 the traffic over
+		  ethernet is encapsulated/received over 802.1q
+		  VLAN tagged frames.
 
 The following environment variables may be used and automatically
 updated by the network boot commands ("bootp" and "rarpboot"),
@@ -2406,8 +2668,9 @@ from a "data file" which is used as image payload:
 	  -n ==> set image name to 'name'
 	  -d ==> use image data from 'datafile'
 
-Right now, all Linux kernels use the same load address	(0x00000000),
-but the entry point address depends on the kernel version:
+Right now, all Linux kernels for PowerPC systems use the same load
+address (0x00000000), but the entry point address depends on the
+kernel version:
 
 - 2.2.x kernels have the entry point at 0x0000000C,
 - 2.3.x and later kernels have the entry point at 0x00000000.

board/AtmarkTechno/suzaku/Makefile

@@ -1,5 +1,5 @@
 #
-# (C) Copyright 2000-2003
+# (C) Copyright 2003
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this

board/AtmarkTechno/suzaku/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2004 Atmark Techno, Inc.
+#
+# Yasushi SHOJI <yashi@atmark-techno.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x80F00000
+
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+PLATFORM_CPPFLAGS += -mxl-barrel-shift

board/AtmarkTechno/suzaku/flash.c

@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+unsigned long flash_init(void)
+{
+	return 0;
+}
+
+void flash_print_info(flash_info_t *info)
+{
+}
+
+int flash_erase(flash_info_t *info, int s_first, int s_last)
+{
+	return 0;
+}
+
+int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	return 0;
+}

board/AtmarkTechno/suzaku/suzaku.c

@@ -0,0 +1,32 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This is a board specific file.  It's OK to include board specific
+ * header files */
+#include <asm/suzaku.h>
+
+void do_reset(void)
+{
+	*((unsigned long *)(MICROBLAZE_SYSREG_BASE_ADDR)) = MICROBLAZE_SYSREG_RECONFIGURE;
+}

board/AtmarkTechno/suzaku/u-boot.lds

@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(microblaze)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text ALIGN(0x4):
+	{
+		__text_start = .;
+		cpu/microblaze/start.o (.text)
+		*(.text)
+		__text_end = .;
+	}
+
+	.rodata ALIGN(0x4):
+	{
+		__rodata_start = .;
+		*(.rodata)
+		__rodata_end = .;
+	}
+
+	.data ALIGN(0x4):
+	{
+		__data_start = .;
+		*(.data)
+		__data_end = .;
+	}
+
+	.u_boot_cmd ALIGN(0x4):
+	{
+		__u_boot_cmd_start = .;
+		*(.u_boot_cmd)
+		__u_boot_cmd_end = .;
+	}
+
+	.bss ALIGN(0x4):
+	{
+		__bss_start = .;
+		*(.bss)
+		__bss_start = .;
+	}
+}

board/RPXlite_dw/Makefile

@@ -1,5 +1,5 @@
 #
-# (C) Copyright 2000-2002
+# (C) Copyright 2000-2004
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this

board/RPXlite_dw/README

@@ -0,0 +1,96 @@
+
+After following the step of Yoo. Jonghoon and Wolfgang Denk,
+I ported u-boot on RPXlite DW version board: RPXlite_DW or LITE_DW.
+
+There are three differences between the Yoo-ported RPXlite and the RPXlite_DW.
+
+Board(in U-BOOT)	version(in EmbeddedPlanet)	CPU	SDRAM	FLASH
+RPXlite				RPXlite CW		850	16MB	4MB
+RPXlite_DW			RPXlite DW		823e	64MB	16MB
+
+This fireware is specially coded for EmbeddedPlanet Co. Software Development
+Platform(RPXlite DW),which has a NEC NL6448BC20-08 LCD panel.
+
+It has the following three features:
+
+1. 64MHz/48MHz system frequence setting options.
+The default setting is 48MHz.To get a 64MHz u-boot,just add
+'64' in make command,like
+
+make RPXlite_DW_64_config
+make all
+
+2. CFG_ENV_IS_IN_FLASH/CFG_ENV_IS_IN_NVRAM
+
+The default environment parameter is stored in FLASH because it is a common choice for
+environment parameter.So I make NVRAM as backup parameter storeage.The reason why I
+didn't use EEPROM for ENV is that PlanetCore V2.0 use EEPROM as environment parameter
+home.Because of the possibility of using two firewares on this board,I didn't
+'disturb' EEPROM.To get NVRAM support,you may use the following build command:
+
+make RPXlite_DW_NVRAM_config
+make all
+
+3. LCD panel support
+
+To support the Platform better,I added LCD panel(NL6448BC20-08) function.But bewear of
+the fact that once you build this support and program it to FLASH,you should make sure
+you put workable kernel and ramdisk at the right place in FLASH or through NFS.
+Otherwise, you must erase this fireware manually via BDI2000 or ICE tools.So this
+function is used for deployment and demo only.Pls look before you leap.
+
+To get a LCD support u-boot,you can do the following:
+
+make RPXlite_DW_LCD_config
+make all
+
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The basic make commands could be:
+
+make RPXlite_DW_config
+make RPXlite_DW_64_config
+make RPXlite_DW_LCD_config
+make RPXlite_DW_NVRAM_config
+
+BTW,you can combine the above features together and get a workable u-boot to meet your need.
+For example,to get a 64MHZ && ENV_IS_IN_FLASH && LCD panel support u-boot,you can type:
+
+make RPXlite_DW_NVRAM_64_LCD_config
+make all
+
+So other combining make commands could be:
+
+make RPXlite_DW_NVRAM_64_config
+make RPXlite_DW_NVRAM_LCD_config
+make RPXlite_DW_64_LCD_config
+
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The boot process by "make RPXlite_DW_config" could be:
+
+U-Boot 1.1.1 (Jun  8 2004 - 11:16:30)
+
+CPU:   PPC823EZTnnB2 at 48 MHz: 16 kB I-Cache 8 kB D-Cache
+Board: RPXlite_DW
+DRAM:  64 MB
+FLASH: 16 MB
+*** Warning - bad CRC, using default environment
+
+In:    serial
+Out:   serial
+Err:   serial
+Net:   SCC ETHERNET
+u-boot>
+
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+I'd like to extend my heartfelt gratitute to kind people for helping me work it out.
+I would particually thank Wolfgang Denk for his nice help.
+
+Enjoy,
+
+Sam Song, samsongshu@yahoo.com.cn
+Institute of Electrical Machinery and Controls
+Shanghai University
+
+June 8,2004

board/RPXlite_dw/RPXlite_dw.c

@@ -0,0 +1,180 @@
+/*
+ * (C) Copyright 2004
+ * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Sam Song
+ * U-Boot port on RPXlite DW board : RPXlite_DW or LITE_DW
+ * Tested on working at 64MHz(CPU)/32MHz(BUS),48MHz/24MHz
+ * with 64MB, 2 SDRAM Micron chips,MT48LC16M16A2-75.
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+
+/* ------------------------------------------------------------------------- */
+static long int dram_size (long int, long int *, long int);
+/* ------------------------------------------------------------------------- */
+
+#define	_NOT_USED_	0xFFFFCC25
+
+const uint sdram_table[] =
+{
+	/*
+	 * Single Read. (Offset 00h in UPMA RAM)
+	 */
+	0x0F03CC04, 0x00ACCC24, 0x1FF74C20, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_,
+
+	/*
+	 * Burst Read. (Offset 08h in UPMA RAM)
+	 */
+	0x0F03CC04, 0x00ACCC24, 0x00FFCC20, 0x00FFCC20,
+	0x01FFCC20, 0x1FF74C20, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_,
+
+	/*
+	 * Single Write. (Offset 18h in UPMA RAM)
+	 */
+	0x0F03CC02, 0x00AC0C24, 0x1FF74C25, /* last */
+	_NOT_USED_, _NOT_USED_, 0x0FA00C34,0x0FFFCC35,
+	_NOT_USED_,
+
+	/*
+	 * Burst Write. (Offset 20h in UPMA RAM)
+	 */
+	0x0F03CC00, 0x00AC0C20, 0x00FFFC20, 0x00FFFC22,
+	0x01FFFC24, 0x1FF74C25, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_,
+
+	/*
+	 * Refresh. (Offset 30h in UPMA RAM)
+	 */
+	0x0FF0CC24, 0xFFFFCC24, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, 0xEFFB8C34, 0x0FF74C34,
+	0x0FFACCB4, 0x0FF5CC34, 0x0FFFCC34, 0x0FFFCCB4,
+	/* INIT sequence RAM WORDS
+	 * SDRAM Initialization (offset 0x36 in UPMA RAM)
+	 * The above definition uses the remaining space
+	 * to establish an initialization sequence,
+	 * which is executed by a RUN command.
+	 * The sequence is COMMAND INHIBIT(NOP),Precharge,
+	 * Load Mode Register,NOP,Auto Refresh.
+	 */
+
+	/*
+	 * Exception. (Offset 3Ch in UPMA RAM)
+	 */
+	0x0FEA8C34, 0x1FB54C34, 0xFFFFCC34, _NOT_USED_
+};
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	puts ("Board: RPXlite_DW\n") ;
+	return (0) ;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	volatile immap_t     *immap  = (immap_t *)CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	long int size9;
+
+	upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
+
+	/* Refresh clock prescalar */
+	memctl->memc_mptpr = CFG_MPTPR ;
+
+	memctl->memc_mar  = 0x00000088;
+
+	/* Map controller banks 1 to the SDRAM bank */
+	memctl->memc_or1 = CFG_OR1_PRELIM;
+	memctl->memc_br1 = CFG_BR1_PRELIM;
+
+	memctl->memc_mamr = CFG_MAMR_9COL & (~(MAMR_PTAE)); /* no refresh yet */
+	/*Disable Periodic timer A. */
+
+ 	udelay(200);
+
+	/* perform SDRAM initializsation sequence */
+
+	memctl->memc_mcr  = 0x80002236; /* SDRAM bank 0 - refresh twice */
+
+	udelay(1);
+
+	memctl->memc_mamr |= MAMR_PTAE;	/* enable refresh */
+
+	/*Enable Periodic timer A */
+
+	udelay (1000);
+
+	 /* Check Bank 0 Memory Size
+	  * try 9 column mode
+	  */
+
+	size9 = dram_size (CFG_MAMR_9COL, (ulong *)SDRAM_BASE_PRELIM, SDRAM_MAX_SIZE);
+
+	/*
+	 * Final mapping:
+	 */
+
+	memctl->memc_or1 = ((-size9) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
+
+	udelay (1000);
+
+	return (size9);
+}
+
+void rpxlite_init (void)
+{
+	/* Enable NVRAM */
+	*((uchar *) BCSR0) |= BCSR0_ENNVRAM;
+}
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+static long int dram_size (long int mamr_value, long int *base,
+			   long int maxsize)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+	memctl->memc_mamr = mamr_value;
+
+	return (get_ram_size (base, maxsize));
+}

board/RPXlite_dw/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# RPXlite dw boards : lite_dw
+#
+
+TEXT_BASE = 0xff000000

board/RPXlite_dw/flash.c

@@ -0,0 +1,490 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Yoo. Jonghoon, IPone, yooth@ipone.co.kr
+ * U-Boot port on RPXlite board
+ *
+ * Some of flash control words are modified. (from 2x16bit device
+ * to 4x8bit device)
+ * RPXLite board I tested has only 4 AM29LV800BB devices. Other devices
+ * are not tested.
+ *
+ * (?) Does an RPXLite board which
+ * 	does not use AM29LV800 flash memory exist ?
+ *	I don't know...
+ */
+
+/* Yes,Yoo.They do use other FLASH for the board.
+ *
+ * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn
+ * U-Boot port on RPXlite DW version board
+ *
+ * By now,it uses 4 AM29DL323DB90VI devices(4x8bit).
+ * The total FLASH has 16MB(4x4MB).
+ * I just made some necessary changes on the basis of Wolfgang and Yoo's job.
+ *
+ * June 8, 2004 */
+
+#include <common.h>
+#include <mpc8xx.h>
+
+flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+/*-----------------------------------------------------------------------
+ * Functions   vu_long : volatile unsigned long IN include/common.h
+ */
+static ulong flash_get_size (vu_long *addr, flash_info_t *info);
+static int write_word (flash_info_t *info, ulong dest, ulong data);
+static void flash_get_offsets (ulong base, flash_info_t *info);
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0 ;
+	int i;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	size_b0 = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
+	flash_get_offsets (CFG_FLASH_BASE, &flash_info[0]);
+
+#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
+	/* If Monitor is in the cope of FLASH,then
+	 * protect this area by default in case for
+	 * other occupation. [SAM] */
+
+	/* monitor protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_MONITOR_BASE,
+		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      &flash_info[0]);
+#endif
+	flash_info[0].size = size_b0;
+	return (size_b0);
+}
+
+static void flash_get_offsets (ulong base, flash_info_t *info)
+{
+	int i;
+
+	/* set up sector start address table */
+	if (info->flash_id & FLASH_BTYPE) {
+		info->start[0] = base + 0x00000000;
+		info->start[1] = base + 0x00008000;
+		info->start[2] = base + 0x00010000;
+		info->start[3] = base + 0x00018000;
+		info->start[4] = base + 0x00020000;
+		info->start[5] = base + 0x00028000;
+		info->start[6] = base + 0x00030000;
+		info->start[7] = base + 0x00038000;
+
+		for (i = 8; i < info->sector_count; i++) {
+			info->start[i] = base + ((i-7) * 0x00040000);
+		}
+	} else {
+		i = info->sector_count - 1;
+		info->start[i--] = base + info->size - 0x00010000;
+		info->start[i--] = base + info->size - 0x00018000;
+		info->start[i--] = base + info->size - 0x00020000;
+		for (; i >= 0; i--) {
+			info->start[i] = base + i * 0x00040000;
+		}
+	}
+
+}
+
+void flash_print_info  (flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:	printf ("AMD ");		break;
+	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
+	default:		printf ("Unknown Vendor ");	break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AM400B:	printf ("AM29LV400B (4 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM400T:	printf ("AM29LV400T (4 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM800B:	printf ("AM29LV800B (8 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM800T:	printf ("AM29LV800T (8 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM160B:	printf ("AM29LV160B (16 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM160T:	printf ("AM29LV160T (16 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM320B:	printf ("AM29LV320B (32 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM320T:	printf ("AM29LV320T (32 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AMDL323B:    printf ("AM29DL323B (32 Mbit, bottom boot sector)\n");
+				break;
+	/* I just add the FLASH_AMDL323B for RPXlite_DW BOARD. [SAM]  */
+	default:		printf ("Unknown Chip Type\n");
+				break;
+	}
+	printf ("  Size: %ld MB in %d Sectors\n",info->size >> 20, info->sector_count);
+	printf ("  Sector Start Addresses:");
+	for (i=0; i<info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",info->start[i],info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+static ulong flash_get_size (vu_long *addr, flash_info_t *info)
+{
+	short i;
+	ulong value;
+	ulong base = (ulong)addr;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0xAAA] = 0x00AA00AA ;
+	addr[0x555] = 0x00550055 ;
+	addr[0xAAA] = 0x00900090 ;
+
+	value = addr[0] ;
+	switch (value & 0x00FF00FF) {
+	case AMD_MANUFACT:             		/* AMD_MANUFACT=0x00010001 in flash.h. */
+		info->flash_id = FLASH_MAN_AMD; /* FLASH_MAN_AMD=0x00000000 in flash.h.*/
+		break;
+	case FUJ_MANUFACT:
+		info->flash_id = FLASH_MAN_FUJ;
+		break;
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);			/* no or unknown flash	*/
+	}
+
+	value = addr[2] ;			/* device ID		*/
+	switch (value & 0x00FF00FF) {
+	case (AMD_ID_LV400T & 0x00FF00FF):
+		info->flash_id += FLASH_AM400T;
+		info->sector_count = 11;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+	case (AMD_ID_LV400B & 0x00FF00FF):
+		info->flash_id += FLASH_AM400B;
+		info->sector_count = 11;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+	case (AMD_ID_LV800T & 0x00FF00FF):
+		info->flash_id += FLASH_AM800T;
+		info->sector_count = 19;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+	case (AMD_ID_LV800B & 0x00FF00FF):
+		info->flash_id += FLASH_AM800B;
+		info->sector_count = 19;
+		info->size = 0x00400000;	/* Size doubled by yooth */
+		break;				/* => 4 MB		 */
+	case (AMD_ID_LV160T & 0x00FF00FF):
+		info->flash_id += FLASH_AM160T;
+		info->sector_count = 35;
+		info->size = 0x00400000;
+		break;				/* => 4 MB		*/
+	case (AMD_ID_LV160B & 0x00FF00FF):
+		info->flash_id += FLASH_AM160B;
+		info->sector_count = 35;
+		info->size = 0x00400000;
+		break;				/* => 4 MB		*/
+	case (AMD_ID_DL323B & 0x00FF00FF):
+		info->flash_id += FLASH_AMDL323B;
+		info->sector_count = 71;
+		info->size = 0x01000000;
+		break;                          /* => 16 MB(4x4MB)  */
+	/* AMD_ID_DL323B= 0x22532253  FLASH_AMDL323B= 0x0013
+	 * AMD_ID_DL323B could be found in <flash.h>.[SAM]
+	 * So we could get : flash_id = 0x00000013.
+	 * The first four-bit represents VEDOR ID,leaving others for FLASH ID. */
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);			/* => no or unknown flash */
+
+	}
+	/* set up sector start address table */
+	if (info->flash_id & FLASH_BTYPE) {
+	/* FLASH_BTYPE=0x0001 mask for bottom boot sector type.If the last bit equals 1,
+	 * it means bottom boot flash. GOOD IDEA! [SAM]
+	 */
+
+	/* set sector offsets for bottom boot block type        */
+		info->start[0] = base + 0x00000000;
+		info->start[1] = base + 0x00008000;
+		info->start[2] = base + 0x00010000;
+		info->start[3] = base + 0x00018000;
+		info->start[4] = base + 0x00020000;
+		info->start[5] = base + 0x00028000;
+		info->start[6] = base + 0x00030000;
+		info->start[7] = base + 0x00038000;
+
+		for (i = 8; i < info->sector_count; i++) {
+			info->start[i] = base + ((i-7) * 0x00040000) ;
+		}
+	} else {
+		/* set sector offsets for top boot block type		*/
+		i = info->sector_count - 1;
+		info->start[i--] = base + info->size - 0x00010000;
+		info->start[i--] = base + info->size - 0x00018000;
+		info->start[i--] = base + info->size - 0x00020000;
+		for (; i >= 0; i--) {
+			info->start[i] = base + i * 0x00040000;
+		}
+	}
+
+	/* check for protected sectors */
+	for (i = 0; i < info->sector_count; i++) {
+		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
+		/* D0 = 1 if protected */
+		addr = (volatile unsigned long *)(info->start[i]);
+		/* info->protect[i] = addr[4] & 1 ; */
+		/* Mask it for disorder FLASH protection **[Sam]** */
+	}
+
+	/*
+	 * Prevent writes to uninitialized FLASH.
+	 */
+	if (info->flash_id != FLASH_UNKNOWN) {
+		addr = (volatile unsigned long *)info->start[0];
+
+		*addr = 0xF0F0F0F0;	/* reset bank */
+	}
+	return (info->size);
+}
+
+int	flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	vu_long *addr = (vu_long*)(info->start[0]);
+	int flag, prot, sect, l_sect;
+	ulong start, now, last;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	if ((info->flash_id == FLASH_UNKNOWN) ||
+	    (info->flash_id > FLASH_AMD_COMP)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+			info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect=s_first; sect<=s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	l_sect = -1;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	addr[0xAAA] = 0xAAAAAAAA;
+	addr[0x555] = 0x55555555;
+	addr[0xAAA] = 0x80808080;
+	addr[0xAAA] = 0xAAAAAAAA;
+	addr[0x555] = 0x55555555;
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect<=s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			addr = (vu_long *)(info->start[sect]) ;
+			addr[0] = 0x30303030 ;
+			l_sect = sect;
+		}
+	}
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* wait at least 80us - let's wait 1 ms */
+	udelay (1000);
+
+	/*
+	 * We wait for the last triggered sector
+	 */
+	if (l_sect < 0)
+		goto DONE;
+
+	start = get_timer (0);
+	last  = start;
+	addr = (vu_long *)(info->start[l_sect]);
+	while ((addr[0] & 0x80808080) != 0x80808080) {
+		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+			printf ("Timeout\n");
+			return 1;
+		}
+		/* show that we're waiting */
+		if ((now - last) > 1000) {	/* every second */
+			putc ('.');
+			last = now;
+		}
+	}
+
+DONE:
+	/* reset to read mode */
+	addr = (vu_long *)info->start[0];
+	addr[0] = 0xF0F0F0F0;	/* reset bank */
+
+	printf (" done\n");
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong cp, wp, data;
+	int i, l, rc;
+
+	wp = (addr & ~3);	/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i=0, cp=wp; i<l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+		for (; i<4 && cnt>0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt==0 && i<4; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 4;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 4) {
+		data = 0;
+		for (i=0; i<4; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp  += 4;
+		cnt -= 4;
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i<4; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *)cp);
+	}
+	return (write_word(info, wp, data));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word (flash_info_t *info, ulong dest, ulong data)
+{
+	vu_long *addr = (vu_long *)(info->start[0]);
+	ulong start;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*((vu_long *)dest) & data) != data) {
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	addr[0xAAA] = 0xAAAAAAAA;
+	addr[0x555] = 0x55555555;
+	addr[0xAAA] = 0xA0A0A0A0;
+
+	*((vu_long *)dest) = data;
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* data polling for D7 */
+	start = get_timer (0);
+	while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080)) {
+		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
+			return (1);
+		}
+	}
+	return (0);
+}

board/RPXlite_dw/u-boot.lds

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -57,17 +57,15 @@ SECTIONS
     /* the sector layout of our flash chips!	XXX FIXME XXX	*/
 
     cpu/mpc8xx/start.o	(.text)
-/*
-    cpu/mpc8xx/start.o	(.text)
     common/dlmalloc.o	(.text)
     lib_ppc/ppcstring.o	(.text)
     lib_generic/vsprintf.o	(.text)
     lib_generic/crc32.o		(.text)
     lib_generic/zlib.o		(.text)
-
+/* XXX ?
     . = env_offset;
-    common/environment.o(.text)
 */
+    common/environment.o(.text)
 
     *(.text)
     *(.fixup)
@@ -86,7 +84,7 @@ SECTIONS
   .dtors     : { *(.dtors)   }
 
   /* Read-write section, merged into data segment: */
-  . = (. + 0x0FFF) & 0xFFFFF000;
+  . = (. + 0x00FF) & 0xFFFFFF00;
   _erotext = .;
   PROVIDE (erotext = .);
   .reloc   :
@@ -136,11 +134,6 @@ SECTIONS
    *(.bss)
    *(COMMON)
   }
-  . = ALIGN(256 * 1024);
-  .ppcenv	:
-  {
-    common/environment.o (.ppcenv)
-  }
   _end = . ;
   PROVIDE (end = .);
 }

board/RPXlite_dw/u-boot.lds.debug

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2002
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this

board/adder/Makefile

@@ -0,0 +1,46 @@
+#
+# Copyright (C) 2004 Arabella Software Ltd.
+# Yuli Barcohen <yuli@arabellasw.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/adder/adder.c

@@ -0,0 +1,107 @@
+/*
+ * Copyright (C) 2004 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * Support for Analogue&Micro Adder boards family.
+ * Tested on AdderII and Adder87x.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+
+/*
+ * SDRAM is single Samsung K4S643232F-T70 chip.
+ * Minimal CPU frequency is 40MHz.
+ */
+static uint sdram_table[] = {
+	/* Single read	(offset 0x00 in UPM RAM) */
+	0x1f07fc24, 0xe0aefc04, 0x10adfc04, 0xe0bbbc00,
+	0x10f77c44, 0xf3fffc07, 0xfffffc04, 0xfffffc04,
+
+	/* Burst read	(offset 0x08 in UPM RAM) */
+	0x1f07fc24, 0xe0aefc04, 0x10adfc04, 0xf0affc00,
+	0xf0affc00, 0xf0affc00, 0xf0affc00, 0x10a77c44,
+	0xf7bffc47, 0xfffffc35, 0xfffffc34, 0xfffffc35,
+	0xfffffc35, 0x1ff77c35, 0xfffffc34, 0x1fb57c35,
+
+	/* Single write (offset 0x18 in UPM RAM) */
+	0x1f27fc24, 0xe0aebc04, 0x00b93c00, 0x13f77c47,
+	0xfffdfc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+
+	/* Burst write	(offset 0x20 in UPM RAM) */
+	0x1f07fc24, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
+	0xf0affc00, 0xe0abbc00, 0x1fb77c47, 0xfffffc04,
+	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+
+	/* Refresh	(offset 0x30 in UPM RAM) */
+	0x1ff5fca4, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+	0xfffffc84, 0xfffffc07, 0xfffffc04, 0xfffffc04,
+	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+
+	/* Exception	(offset 0x3C in UPM RAM) */
+	0xfffffc27, 0xfffffc04, 0xfffffc04, 0xfffffc04
+};
+
+long int initdram (int board_type)
+{
+	long int msize = CFG_SDRAM_SIZE;
+	volatile immap_t     *immap  = (volatile immap_t *)CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+	upmconfig(UPMA, sdram_table, sizeof(sdram_table) / sizeof(uint));
+
+	/* Configure SDRAM refresh */
+	memctl->memc_mptpr = MPTPR_PTP_DIV32; /* BRGCLK/32 */
+
+	memctl->memc_mamr = (94 << 24) | CFG_MAMR;
+	memctl->memc_mar  = 0x0;
+	udelay(200);
+
+	/* Run precharge from location 0x15 */
+	memctl->memc_mcr = 0x80002115;
+	udelay(200);
+
+	/* Run 8 refresh cycles */
+	memctl->memc_mcr = 0x80002830;
+	udelay(200);
+
+	memctl->memc_mar = 0x88;
+	udelay(200);
+
+	/* Run MRS pattern from location 0x16 */
+	memctl->memc_mcr = 0x80002116;
+	udelay(200);
+
+	return msize;
+}
+
+int checkboard( void )
+{
+	puts("Board: Adder");
+#if defined(CONFIG_MPC885_FAMILY)
+	puts("87x\n");
+#elif defined(CONFIG_MPC866_FAMILY)
+	puts("II\n");
+#endif
+
+	return 0;
+}

board/adder/config.mk

@@ -0,0 +1,27 @@
+#
+# Copyright (C) 2004 Arabella Software Ltd.
+# Yuli Barcohen <yuli@arabellasw.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Analogue&Micro Adder boards family
+#
+TEXT_BASE = 0xFE000000

board/adder/u-boot.lds

@@ -0,0 +1,122 @@
+/*
+ * (C) Copyright 2001-2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Modified by Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp        : { *(.interp)		}
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt           : { *(.plt)		}
+  .text          :
+  {
+    cpu/mpc8xx/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
+ENTRY(_start)

board/adderII/adderII.c

@@ -1,189 +0,0 @@
-/*
- * (C) Copyright 2000-2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <config.h>
-#include <mpc8xx.h>
-
-/*
- * Check Board Identity:
- */
-
-int checkboard( void )
-{
-	puts("Board: ");
-	puts("AdderII(MPC852T)\n" );
-
-  	return 0;
-}
-
-#if defined( CONFIG_SDRAM_50MHZ )
-
-/******************************************************************************
-** for chip Samsung K4S643232F - T70
-** this table is for 32-50MHz operation
-*******************************************************************************/
-
-#define SDRAM_MPTPRVALUE 	0x0200
-
-#define SDRAM_MAMRVALUE0 	0x00802114   /* refresh at 32MHz */
-#define SDRAM_MAMRVALUE1 	0x00802118
-
-#define SDRAM_OR1VALUE   	0xff800e00
-#define SDRAM_BR1VALUE   	0x00000081
-
-#define SDRAM_MARVALUE		94
-
-#define SDRAM_MCRVALUE0  	0x80808105
-#define SDRAM_MCRVALUE1  	0x80808130
-
-const uint sdram_table[] = {
-
-	/* single read   (offset 0x00 in upm ram) */
-       	0x1f07fc24, 0xe0aefc04, 0x10adfc04, 0xe0bbbc00,
-       	0x10f77c44, 0xf3fffc07, 0xfffffc04, 0xfffffc04,
-
-	/* burst read    (offset 0x08 in upm ram) */
-       	0x1f07fc24, 0xe0aefc04, 0x10adfc04, 0xf0affc00,
-       	0xf0affc00, 0xf0affc00, 0xf0affc00, 0x10a77c44,
-       	0xf7bffc47, 0xfffffc35, 0xfffffc34, 0xfffffc35,
-       	0xfffffc35, 0x1ff77c35, 0xfffffc34, 0x1fb57c35,
-
-	/* single write  (offset 0x18 in upm ram) */
-       	0x1f27fc24, 0xe0aebc04, 0x00b93c00, 0x13f77c47,
-       	0xfffdfc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-
-	/* burst write   (offset 0x20 in upm ram) */
-       	0x1f07fc24, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
-       	0xf0affc00, 0xe0abbc00, 0x1fb77c47, 0xfffffc04,
-       	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-       	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-
-	/* refresh       (offset 0x30 in upm ram) */
-       	0x1ff5fca4, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-       	0xfffffc84, 0xfffffc07, 0xfffffc04, 0xfffffc04,
-       	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-
-	/* exception     (offset 0x3C in upm ram) */
-       	0xfffffc27, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-};
-
-#else
-#error SDRAM not correctly configured
-#endif
-
-int _initsdram (uint base, uint noMbytes)
-{
-	volatile immap_t *immap = (immap_t *) CFG_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-
-	if (noMbytes != 8) {
-		return -1;
-	}
-
-	upmconfig (UPMA, (uint *) sdram_table,
-		   sizeof (sdram_table) / sizeof (uint));
-
-	memctl->memc_mptpr = SDRAM_MPTPRVALUE;
-
-	/* Configure the refresh (mostly).  This needs to be
-	 * based upon processor clock speed and optimized to provide
-	 * the highest level of performance.  For multiple banks,
-	 * this time has to be divided by the number of banks.
-	 * Although it is not clear anywhere, it appears the
-	 * refresh steps through the chip selects for this UPM
-	 * on each refresh cycle.
-	 * We have to be careful changing
-	 * UPM registers after we ask it to run these commands.
-	 */
-
-	memctl->memc_mamr = (SDRAM_MAMRVALUE0 | (SDRAM_MARVALUE << 24));
-	memctl->memc_mar = 0x0;
-	udelay (200);
-
-	/* Now run the precharge/nop/mrs commands.
-	 */
-	memctl->memc_mcr = 0x80002115;
-	udelay (200);
-
-	/* Run 8 refresh cycles */
-	memctl->memc_mcr = 0x80002380;
-	udelay (200);
-
-	memctl->memc_mar = 0x88;
-	udelay (200);
-
-	memctl->memc_mcr = 0x80002116;
-	udelay (200);
-
-	memctl->memc_or1 = SDRAM_OR1VALUE;
-	memctl->memc_br1 = SDRAM_BR1VALUE | base;
-
-	return 0;
-}
-
-void _sdramdisable( void )
-{
-	volatile immap_t     *immap = (immap_t *)CFG_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-
-	memctl->memc_br1 = 0x00000000;
-
-	/* maybe we should turn off upma here or something */
-}
-
-int initsdram (uint base, uint * noMbytes)
-{
-	uint m = 8;
-
-	*noMbytes = m;
-
-	if (!_initsdram (base, m)) {
-		return 0;
-	} else {
-		_sdramdisable ();
-		return -1;
-	}
-}
-
-long int initdram (int board_type)
-{
-	/* AdderII: has 8MB SDRAM */
-	uint sdramsz;
-	uint m = 0;
-
-	if (!initsdram (0x00000000, &sdramsz)) {
-		m += sdramsz;
-	} else {
-		return -1;
-	}
-	return (m << 20);
-}
-
-int testdram (void)
-{
-	/* TODO: XXX XXX XXX not an actual SDRAM test */
-	printf ("Test: 8MB SDRAM\n");
-
-	return (0);
-}

board/altera/dk1c20/vectors.S

@@ -38,6 +38,8 @@
  *	_cwp_lolimit	-Handles register window underflows.
  *	_cwp_hilimit	-Handles register window overflows.
  *	_timebase_int	-Increments the timebase.
+ *	_brkpt_hw_int	-Hardware breakpoint handler.
+ *	_brkpt_sw_int	-Software breakpoint handler.
  *	_def_xhandler	-Default exception handler.
  *
  * _timebase_int handles a Nios Timer interrupt and increments the
@@ -58,9 +60,8 @@ _vectors:
 	.long	_def_xhandler@h		/* Vector 0  - NMI */
 	.long	_cwp_lolimit@h		/* Vector 1  -  underflow */
 	.long	_cwp_hilimit@h		/* Vector 2  - overflow	*/
-
-	.long	_def_xhandler@h		/* Vector 3 - GNUPro debug */
-	.long	_def_xhandler@h		/* Vector 4 - GNUPro debug */
+	.long	_brkpt_hw_int@h		/* Vector 3 - Breakpoint */
+	.long	_brkpt_sw_int@h		/* Vector 4 - Single step*/
 	.long	_def_xhandler@h		/* Vector 5 - GNUPro debug */
 	.long	_def_xhandler@h		/* Vector 6 - future reserved */
 	.long	_def_xhandler@h		/* Vector 7 - future reserved */

board/assabet/Makefile

@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# 2004 (c) MontaVista Software, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= assabet.o
+SOBJS	:= setup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/assabet/assabet.c

@@ -0,0 +1,121 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * 2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <SA-1100.h>
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Board dependent initialisation
+ */
+
+#define ECOR			0x8000
+#define ECOR_RESET		0x80
+#define ECOR_LEVEL_IRQ		0x40
+#define ECOR_WR_ATTRIB		0x04
+#define ECOR_ENABLE		0x01
+
+#define ECSR			0x8002
+#define ECSR_IOIS8		0x20
+#define ECSR_PWRDWN		0x04
+#define ECSR_INT		0x02
+#define SMC_IO_SHIFT		2
+#define NCR_0           	(*((volatile u_char *)(0x100000a0)))
+#define NCR_ENET_OSC_EN		(1<<3)
+
+static inline u8
+readb(volatile u8 * p)
+{
+	return *p;
+}
+
+static inline void
+writeb(u8 v, volatile u8 * p)
+{
+	*p = v;
+}
+
+static void
+smc_init(void)
+{
+	u8 ecor;
+	u8 ecsr;
+	volatile u8 *addr = (volatile u8 *)(0x18000000 + (1 << 25));
+
+	NCR_0 |= NCR_ENET_OSC_EN;
+	udelay(100);
+
+	ecor = readb(addr + (ECOR << SMC_IO_SHIFT)) & ~ECOR_RESET;
+	writeb(ecor | ECOR_RESET, addr + (ECOR << SMC_IO_SHIFT));
+	udelay(100);
+
+	/*
+	 * The device will ignore all writes to the enable bit while
+	 * reset is asserted, even if the reset bit is cleared in the
+	 * same write.  Must clear reset first, then enable the device.
+	 */
+	writeb(ecor, addr + (ECOR << SMC_IO_SHIFT));
+	writeb(ecor | ECOR_ENABLE, addr + (ECOR << SMC_IO_SHIFT));
+
+	/*
+	 * Set the appropriate byte/word mode.
+	 */
+	ecsr = readb(addr + (ECSR << SMC_IO_SHIFT)) & ~ECSR_IOIS8;
+	ecsr |= ECSR_IOIS8;
+	writeb(ecsr, addr + (ECSR << SMC_IO_SHIFT));
+	udelay(100);
+}
+
+static void
+neponset_init(void)
+{
+	smc_init();
+}
+
+int
+board_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_arch_number = 25;	/* Intel Assabet Board */
+	gd->bd->bi_boot_params = 0xc0000100;
+
+	neponset_init();
+
+	return 0;
+}
+
+int
+dram_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return (0);
+}

board/assabet/config.mk

@@ -0,0 +1,7 @@
+#
+# SA-1110 based Intel Assabet board
+#
+# The Intel Assabet 1 bank of 32 MiB SDRAM
+#
+
+TEXT_BASE = 0xc1f00000

board/assabet/setup.S

@@ -0,0 +1,136 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
+ *		       Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
+ * 2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include "config.h"
+#include "version.h"
+
+
+/*-----------------------------------------------------------------------
+ * Board defines:
+ */
+
+#define MDCNFG		0x00
+#define MDCAS00		0x04
+#define MDCAS01		0x08
+#define MDCAS02		0x0C
+#define MSC0		0x10
+#define MSC1		0x14
+#define MECR		0x18
+#define MDREFR		0x1C
+#define MDCAS20		0x20
+#define MDCAS21		0x24
+#define MDCAS22		0x28
+#define MSC2		0x2C
+#define SMCNFG		0x30
+
+#define ASSABET_BCR		(0x12000000)
+#define ASSABET_BCR_DB1110	(0x00a07490 | (0<<16) | (0<<17))
+#define ASSABET_SCR_nNEPONSET	(1 << 9)
+#define NEPONSET_LEDS		(0x10000010)
+
+
+/*-----------------------------------------------------------------------
+ * Setup parameters for the board:
+ */
+
+
+MEM_BASE:	.long	0xa0000000
+MEM_START:	.long	0xc0000000
+
+mdcnfg:		.long	0x72547254
+mdcas00:	.long	0xaaaaaa7f
+mdcas01:	.long	0xaaaaaaaa
+mdcas02:	.long	0xaaaaaaaa
+msc0:		.long	0x4b384370
+msc1:		.long	0x22212419
+mecr:		.long	0x994a994a
+mdrefr:		.long	0x04340327
+mdcas20:	.long	0xaaaaaa7f
+mdcas21:	.long	0xaaaaaaaa
+mdcas22:	.long	0xaaaaaaaa
+msc2:		.long	0x42196669
+smcnfg:		.long	0x00000000
+
+BCR:		.long	ASSABET_BCR
+BCR_DB1110:	.long	ASSABET_BCR_DB1110
+LEDS:		.long	NEPONSET_LEDS
+
+
+	.globl memsetup
+memsetup:
+
+	/* Setting up the memory and stuff */
+
+	ldr	r0, MEM_BASE
+	ldr	r1, mdcas00
+	str	r1, [r0, #MDCAS00]
+	ldr	r1, mdcas01
+	str	r1, [r0, #MDCAS01]
+	ldr	r1, mdcas02
+	str	r1, [r0, #MDCAS02]
+	ldr	r1, mdcas20
+	str	r1, [r0, #MDCAS20]
+	ldr	r1, mdcas21
+	str	r1, [r0, #MDCAS21]
+	ldr	r1, mdcas22
+	str	r1, [r0, #MDCAS22]
+	ldr	r1, mdrefr
+	str	r1, [r0, #MDREFR]
+	ldr	r1, mecr
+	str	r1, [r0, #MECR]
+	ldr	r1, msc0
+	str	r1, [r0, #MSC0]
+	ldr	r1, msc1
+	str	r1, [r0, #MSC1]
+	ldr	r1, msc2
+	str	r1, [r0, #MSC2]
+	ldr	r1, smcnfg
+	str	r1, [r0, #SMCNFG]
+
+	ldr	r1, mdcnfg
+	str	r1, [r0, #MDCNFG]
+
+	/* Load something to activate bank */
+	ldr	r2, MEM_START
+.rept	8
+	ldr	r3, [r2]
+.endr
+
+	/* Enable SDRAM */
+	orr	r1, r1, #0x00000001
+	str	r1, [r0, #MDCNFG]
+
+	ldr	r1, BCR
+	ldr	r2, BCR_DB1110
+	str	r2, [r1]
+
+	ldr	r1, LEDS
+	mov	r0, #0x3
+	str	r0, [r1]
+
+	/* All done... */
+	mov	pc, lr

board/assabet/u-boot.lds

@@ -0,0 +1,57 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * 2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+		cpu/sa1100/start.o	(.text)
+		*(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/at91rm9200dk/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= at91rm9200dk.o flash.o
+OBJS	:= at91rm9200dk.o at45.o dm9161.o flash.o
 SOBJS	:=
 
 $(LIB):	$(OBJS) $(SOBJS)

board/at91rm9200dk/at45.c

@@ -25,7 +25,14 @@
 #ifdef CONFIG_HAS_DATAFLASH
 #include <dataflash.h>
 
-#define SPI_CLK 5000000
+#define AT91C_SPI_CLK	10000000	/* Max Value = 10MHz to be compliant to
+the Continuous Array Read function */
+
+/* AC Characteristics */
+/* DLYBS = tCSS = 250ns min and DLYBCT = tCSH = 250ns */
+#define DATAFLASH_TCSS	(0xC << 16)
+#define DATAFLASH_TCHS	(0x1 << 24)
+
 #define AT91C_TIMEOUT_WRDY			200000
 #define AT91C_SPI_PCS0_SERIAL_DATAFLASH		0xE     /* Chip Select 0 : NPCS0 %1110 */
 #define AT91C_SPI_PCS3_DATAFLASH_CARD		0x7     /* Chip Select 3 : NPCS3 %0111 */
@@ -50,9 +57,11 @@ void AT91F_SpiInit(void) {
 	AT91C_BASE_SPI->SPI_MR = AT91C_SPI_MSTR | AT91C_SPI_MODFDIS | AT91C_SPI_PCS;
 
 	/* Configure CS0 and CS3 */
-	*(AT91C_SPI_CSR + 0) = AT91C_SPI_CPOL | (AT91C_SPI_DLYBS & 0x100000) | ((AT91C_MASTER_CLOCK / (2*SPI_CLK)) << 8);
+	*(AT91C_SPI_CSR + 0) = AT91C_SPI_CPOL | (AT91C_SPI_DLYBS & DATAFLASH_TCSS) | (AT91C_SPI_DLYBCT &
+	DATAFLASH_TCHS) | ((AT91C_MASTER_CLOCK / (2*AT91C_SPI_CLK)) << 8);
 
-	*(AT91C_SPI_CSR + 3) = AT91C_SPI_CPOL | (AT91C_SPI_DLYBS & 0x100000) | ((AT91C_MASTER_CLOCK / (2*SPI_CLK)) << 8);
+	*(AT91C_SPI_CSR + 3) = AT91C_SPI_CPOL | (AT91C_SPI_DLYBS & DATAFLASH_TCSS) | (AT91C_SPI_DLYBCT &
+	DATAFLASH_TCHS) | ((AT91C_MASTER_CLOCK / (2*AT91C_SPI_CLK)) << 8);
 
 }
 

board/at91rm9200dk/at91rm9200dk.c

@@ -102,6 +102,10 @@ void nand_init (void)
 	*AT91C_PIOB_PER = AT91C_PIO_PB1;	/* enable direct output enable */
 	*AT91C_PIOB_ODR = AT91C_PIO_PB1;	/* disable output */
 
+	/* PIOB and PIOC clock enabling */
+	*AT91C_PMC_PCER = 1 << AT91C_ID_PIOB;
+	*AT91C_PMC_PCER = 1 << AT91C_ID_PIOC;
+
 	if (*AT91C_PIOB_PDSR & AT91C_PIO_PB1)
 		printf ("  No SmartMedia card inserted\n");
 #ifdef DEBUG

board/at91rm9200dk/dm9161.c

@@ -0,0 +1,243 @@
+/*
+ * (C) Copyright 2003
+ * Author : Hamid Ikdoumi (Atmel)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <at91rm9200_net.h>
+#include <net.h>
+#include <dm9161.h>
+
+#ifdef CONFIG_DRIVER_ETHER
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET)
+
+/*
+ * Name:
+ *	dm9161_IsPhyConnected
+ * Description:
+ *	Reads the 2 PHY ID registers
+ * Arguments:
+ *	p_mac - pointer to AT91S_EMAC struct
+ * Return value:
+ *	TRUE - if id read successfully
+ *	FALSE- if error
+ */
+static unsigned int dm9161_IsPhyConnected (AT91PS_EMAC p_mac)
+{
+	unsigned short Id1, Id2;
+
+	at91rm9200_EmacEnableMDIO (p_mac);
+	at91rm9200_EmacReadPhy (p_mac, DM9161_PHYID1, &Id1);
+	at91rm9200_EmacReadPhy (p_mac, DM9161_PHYID2, &Id2);
+	at91rm9200_EmacDisableMDIO (p_mac);
+
+	if ((Id1 == (DM9161_PHYID1_OUI >> 6)) &&
+		((Id2 >> 10) == (DM9161_PHYID1_OUI & DM9161_LSB_MASK)))
+		return TRUE;
+
+	return FALSE;
+}
+
+/*
+ * Name:
+ *	dm9161_GetLinkSpeed
+ * Description:
+ *	Link parallel detection status of MAC is checked and set in the
+ *	MAC configuration registers
+ * Arguments:
+ *	p_mac - pointer to MAC
+ * Return value:
+ *	TRUE - if link status set succesfully
+ *	FALSE - if link status not set
+ */
+static UCHAR dm9161_GetLinkSpeed (AT91PS_EMAC p_mac)
+{
+	unsigned short stat1, stat2;
+
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_BMSR, &stat1))
+		return FALSE;
+
+	if (!(stat1 & DM9161_LINK_STATUS))	/* link status up? */
+		return FALSE;
+
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_DSCSR, &stat2))
+		return FALSE;
+
+	if ((stat1 & DM9161_100BASE_TX_FD) && (stat2 & DM9161_100FDX)) {
+		/*set Emac for 100BaseTX and Full Duplex  */
+		p_mac->EMAC_CFG |= AT91C_EMAC_SPD | AT91C_EMAC_FD;
+		return TRUE;
+	}
+
+	if ((stat1 & DM9161_10BASE_T_FD) && (stat2 & DM9161_10FDX)) {
+		/*set MII for 10BaseT and Full Duplex  */
+		p_mac->EMAC_CFG = (p_mac->EMAC_CFG &
+				~(AT91C_EMAC_SPD | AT91C_EMAC_FD))
+				| AT91C_EMAC_FD;
+		return TRUE;
+	}
+
+	if ((stat1 & DM9161_100BASE_T4_HD) && (stat2 & DM9161_100HDX)) {
+		/*set MII for 100BaseTX and Half Duplex  */
+		p_mac->EMAC_CFG = (p_mac->EMAC_CFG &
+				~(AT91C_EMAC_SPD | AT91C_EMAC_FD))
+				| AT91C_EMAC_SPD;
+		return TRUE;
+	}
+
+	if ((stat1 & DM9161_10BASE_T_HD) && (stat2 & DM9161_10HDX)) {
+		/*set MII for 10BaseT and Half Duplex  */
+		p_mac->EMAC_CFG &= ~(AT91C_EMAC_SPD | AT91C_EMAC_FD);
+		return TRUE;
+	}
+	return FALSE;
+}
+
+
+/*
+ * Name:
+ *	dm9161_InitPhy
+ * Description:
+ *	MAC starts checking its link by using parallel detection and
+ *	Autonegotiation and the same is set in the MAC configuration registers
+ * Arguments:
+ *	p_mac - pointer to struct AT91S_EMAC
+ * Return value:
+ *	TRUE - if link status set succesfully
+ *	FALSE - if link status not set
+ */
+static UCHAR dm9161_InitPhy (AT91PS_EMAC p_mac)
+{
+	UCHAR ret = TRUE;
+	unsigned short IntValue;
+
+	at91rm9200_EmacEnableMDIO (p_mac);
+
+	if (!dm9161_GetLinkSpeed (p_mac)) {
+		/* Try another time */
+		ret = dm9161_GetLinkSpeed (p_mac);
+	}
+
+	/* Disable PHY Interrupts */
+	at91rm9200_EmacReadPhy (p_mac, DM9161_MDINTR, &IntValue);
+	/* clear FDX, SPD, Link, INTR masks */
+	IntValue &= ~(DM9161_FDX_MASK | DM9161_SPD_MASK |
+		      DM9161_LINK_MASK | DM9161_INTR_MASK);
+	at91rm9200_EmacWritePhy (p_mac, DM9161_MDINTR, &IntValue);
+	at91rm9200_EmacDisableMDIO (p_mac);
+
+	return (ret);
+}
+
+
+/*
+ * Name:
+ *	dm9161_AutoNegotiate
+ * Description:
+ *	MAC Autonegotiates with the partner status of same is set in the
+ *	MAC configuration registers
+ * Arguments:
+ *	dev - pointer to struct net_device
+ * Return value:
+ *	TRUE - if link status set successfully
+ *	FALSE - if link status not set
+ */
+static UCHAR dm9161_AutoNegotiate (AT91PS_EMAC p_mac, int *status)
+{
+	unsigned short value;
+	unsigned short PhyAnar;
+	unsigned short PhyAnalpar;
+
+	/* Set dm9161 control register */
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+	value &= ~DM9161_AUTONEG;	/* remove autonegotiation enable */
+	value |= DM9161_ISOLATE;	/* Electrically isolate PHY */
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+
+	/* Set the Auto_negotiation Advertisement Register */
+	/* MII advertising for Next page, 100BaseTxFD and HD, 10BaseTFD and HD, IEEE 802.3 */
+	PhyAnar = DM9161_NP | DM9161_TX_FDX | DM9161_TX_HDX |
+		  DM9161_10_FDX | DM9161_10_HDX | DM9161_AN_IEEE_802_3;
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_ANAR, &PhyAnar))
+		return FALSE;
+
+	/* Read the Control Register     */
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+
+	value |= DM9161_SPEED_SELECT | DM9161_AUTONEG | DM9161_DUPLEX_MODE;
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+	/* Restart Auto_negotiation  */
+	value |= DM9161_RESTART_AUTONEG;
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+
+	/*check AutoNegotiate complete */
+	udelay (10000);
+	at91rm9200_EmacReadPhy (p_mac, DM9161_BMSR, &value);
+	if (!(value & DM9161_AUTONEG_COMP))
+		return FALSE;
+
+	/* Get the AutoNeg Link partner base page */
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_ANLPAR, &PhyAnalpar))
+		return FALSE;
+
+	if ((PhyAnar & DM9161_TX_FDX) && (PhyAnalpar & DM9161_TX_FDX)) {
+		/*set MII for 100BaseTX and Full Duplex  */
+		p_mac->EMAC_CFG |= AT91C_EMAC_SPD | AT91C_EMAC_FD;
+		return TRUE;
+	}
+
+	if ((PhyAnar & DM9161_10_FDX) && (PhyAnalpar & DM9161_10_FDX)) {
+		/*set MII for 10BaseT and Full Duplex  */
+		p_mac->EMAC_CFG = (p_mac->EMAC_CFG &
+				~(AT91C_EMAC_SPD | AT91C_EMAC_FD))
+				| AT91C_EMAC_FD;
+		return TRUE;
+	}
+	return FALSE;
+}
+
+
+/*
+ * Name:
+ *	at91rm92000_GetPhyInterface
+ * Description:
+ *	Initialise the interface functions to the PHY
+ * Arguments:
+ *	None
+ * Return value:
+ *	None
+ */
+void at91rm92000_GetPhyInterface(AT91PS_PhyOps p_phyops)
+{
+	p_phyops->Init = dm9161_InitPhy;
+	p_phyops->IsPhyConnected = dm9161_IsPhyConnected;
+	p_phyops->GetLinkSpeed = dm9161_GetLinkSpeed;
+	p_phyops->AutoNegotiate = dm9161_AutoNegotiate;
+}
+
+#endif	/* CONFIG_COMMANDS & CFG_CMD_NET */
+
+#endif	/* CONFIG_DRIVER_ETHER */

board/at91rm9200dk/flash.c

@@ -42,20 +42,22 @@ typedef struct OrgDef
 /* Flash Organizations */
 OrgDef OrgAT49BV16x4[] =
 {
-	{ 8, 8*1024 }, /* 8 * 8kBytes sectors */
-	{ 2, 32*1024 }, /* 2 * 32kBytes sectors */
-	{ 30, 64*1024 } /* 30 * 64kBytes sectors */
+	{  8,  8*1024 },	/*   8 *  8 kBytes sectors */
+	{  2, 32*1024 },	/*   2 * 32 kBytes sectors */
+	{ 30, 64*1024 },	/*  30 * 64 kBytes sectors */
 };
 
 OrgDef OrgAT49BV16x4A[] =
 {
-	{ 8, 8*1024 }, /* 8 * 8kBytes sectors */
-	{ 31, 64*1024 } /* 31 * 64kBytes sectors */
+	{  8,  8*1024 },	/*   8 *  8 kBytes sectors */
+	{ 31, 64*1024 },	/*  31 * 64 kBytes sectors */
 };
 
-
-#define FLASH_BANK_SIZE 0x200000	/* 2 MB */
-#define MAIN_SECT_SIZE  0x10000		/* 64 KB */
+OrgDef OrgAT49BV6416[] =
+{
+	{   8,  8*1024 },	/*   8 *  8 kBytes sectors */
+	{ 127, 64*1024 },	/* 127 * 64 kBytes sectors */
+};
 
 flash_info_t    flash_info[CFG_MAX_FLASH_BANKS];
 
@@ -73,13 +75,11 @@ flash_info_t    flash_info[CFG_MAX_FLASH_BANKS];
 #define CMD_ERASE_CONFIRM	0x0030
 #define CMD_PROGRAM		0x00A0
 #define CMD_UNLOCK_BYPASS	0x0020
+#define CMD_SECTOR_UNLOCK	0x0070
 
 #define MEM_FLASH_ADDR1		(*(volatile u16 *)(CFG_FLASH_BASE + (0x00005555<<1)))
 #define MEM_FLASH_ADDR2		(*(volatile u16 *)(CFG_FLASH_BASE + (0x00002AAA<<1)))
 
-#define IDENT_FLASH_ADDR1	(*(volatile u16 *)(CFG_FLASH_BASE + (0x0000555<<1)))
-#define IDENT_FLASH_ADDR2	(*(volatile u16 *)(CFG_FLASH_BASE + (0x0000AAA<<1)))
-
 #define BIT_ERASE_DONE		0x0080
 #define BIT_RDY_MASK		0x0080
 #define BIT_PROGRAM_ERROR	0x0020
@@ -95,17 +95,17 @@ void flash_identification (flash_info_t * info)
 {
 	volatile u16 manuf_code, device_code, add_device_code;
 
-	IDENT_FLASH_ADDR1 = FLASH_CODE1;
-	IDENT_FLASH_ADDR2 = FLASH_CODE2;
-	IDENT_FLASH_ADDR1 = ID_IN_CODE;
+	MEM_FLASH_ADDR1 = FLASH_CODE1;
+	MEM_FLASH_ADDR2 = FLASH_CODE2;
+	MEM_FLASH_ADDR1 = ID_IN_CODE;
 
 	manuf_code = *(volatile u16 *) CFG_FLASH_BASE;
 	device_code = *(volatile u16 *) (CFG_FLASH_BASE + 2);
 	add_device_code = *(volatile u16 *) (CFG_FLASH_BASE + (3 << 1));
 
-	IDENT_FLASH_ADDR1 = FLASH_CODE1;
-	IDENT_FLASH_ADDR2 = FLASH_CODE2;
-	IDENT_FLASH_ADDR1 = ID_OUT_CODE;
+	MEM_FLASH_ADDR1 = FLASH_CODE1;
+	MEM_FLASH_ADDR2 = FLASH_CODE2;
+	MEM_FLASH_ADDR1 = ID_OUT_CODE;
 
 	/* Vendor type */
 	info->flash_id = ATM_MANUFACT & FLASH_VENDMASK;
@@ -117,14 +117,36 @@ void flash_identification (flash_info_t * info)
 			(ATM_ID_BV1614A & FLASH_TYPEMASK)) {
 			info->flash_id |= ATM_ID_BV1614A & FLASH_TYPEMASK;
 			printf ("AT49BV1614A (16Mbit)\n");
+		} else {				/* AT49BV1614 Flash */
+			info->flash_id |= ATM_ID_BV1614 & FLASH_TYPEMASK;
+			printf ("AT49BV1614 (16Mbit)\n");
 		}
 
-	} else {				/* AT49BV1614 Flash */
-		info->flash_id |= ATM_ID_BV1614 & FLASH_TYPEMASK;
-		printf ("AT49BV1614 (16Mbit)\n");
+	} else if ((device_code & FLASH_TYPEMASK) == (ATM_ID_BV6416 & FLASH_TYPEMASK)) {
+		info->flash_id |= ATM_ID_BV6416 & FLASH_TYPEMASK;
+		printf ("AT49BV6416 (64Mbit)\n");
 	}
 }
 
+ushort flash_number_sector(OrgDef *pOrgDef, unsigned int nb_blocks)
+{
+	int i, nb_sectors = 0;
+
+	for (i=0; i<nb_blocks; i++){
+		nb_sectors += pOrgDef[i].sector_number;
+	}
+
+	return nb_sectors;
+}
+
+void flash_unlock_sector(flash_info_t * info, unsigned int sector)
+{
+	volatile u16 *addr = (volatile u16 *) (info->start[sector]);
+
+	MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+	*addr = CMD_SECTOR_UNLOCK;
+}
+
 
 ulong flash_init (void)
 {
@@ -140,23 +162,29 @@ ulong flash_init (void)
 
 		flash_identification (&flash_info[i]);
 
-		flash_info[i].size = FLASH_BANK_SIZE;
-
 		if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
 			(ATM_ID_BV1614 & FLASH_TYPEMASK)) {
-			flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
-			memset (flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
 
 			pOrgDef = OrgAT49BV16x4;
 			flash_nb_blocks = sizeof (OrgAT49BV16x4) / sizeof (OrgDef);
-		} else {			/* AT49BV1614A Flash */
-			flash_info[i].sector_count = CFG_MAX_FLASH_SECT - 1;
-			memset (flash_info[i].protect, 0, CFG_MAX_FLASH_SECT - 1);
+		} else if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV1614A & FLASH_TYPEMASK)){	/* AT49BV1614A Flash */
 
 			pOrgDef = OrgAT49BV16x4A;
 			flash_nb_blocks = sizeof (OrgAT49BV16x4A) / sizeof (OrgDef);
+		} else if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV6416 & FLASH_TYPEMASK)){	/* AT49BV6416 Flash */
+
+			pOrgDef = OrgAT49BV6416;
+			flash_nb_blocks = sizeof (OrgAT49BV6416) / sizeof (OrgDef);
+		} else {
+			flash_nb_blocks = 0;
+			pOrgDef = OrgAT49BV16x4;
 		}
 
+		flash_info[i].sector_count = flash_number_sector(pOrgDef, flash_nb_blocks);
+		memset (flash_info[i].protect, 0, flash_info[i].sector_count);
+
 		if (i == 0)
 			flashbase = PHYS_FLASH_1;
 		else
@@ -164,15 +192,26 @@ ulong flash_init (void)
 
 		sector = 0;
 		start_address = flashbase;
+		flash_info[i].size = 0;
 
 		for (j = 0; j < flash_nb_blocks; j++) {
 			for (k = 0; k < pOrgDef[j].sector_number; k++) {
 				flash_info[i].start[sector++] = start_address;
 				start_address += pOrgDef[j].sector_size;
+				flash_info[i].size += pOrgDef[j].sector_size;
 			}
 		}
 
 		size += flash_info[i].size;
+
+		if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV6416 & FLASH_TYPEMASK)){	/* AT49BV6416 Flash */
+
+			/* Unlock all sectors at reset */
+			for (j=0; j<flash_info[i].sector_count; j++){
+				flash_unlock_sector(&flash_info[i], j);
+			}
+		}
 	}
 
 	/* Protect binary boot image */
@@ -215,6 +254,9 @@ void flash_print_info (flash_info_t * info)
 	case (ATM_ID_BV1614A & FLASH_TYPEMASK):
 		printf ("AT49BV1614A (16Mbit)\n");
 		break;
+	case (ATM_ID_BV6416 & FLASH_TYPEMASK):
+		printf ("AT49BV6416 (64Mbit)\n");
+		break;
 	default:
 		printf ("Unknown Chip Type\n");
 		goto Done;
@@ -234,7 +276,7 @@ void flash_print_info (flash_info_t * info)
 	}
 	printf ("\n");
 
-  Done:
+Done:	;
 }
 
 /*-----------------------------------------------------------------------

board/cerf250/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= cerf250.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/cerf250/cerf250.c

@@ -0,0 +1,75 @@
+/*
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* memory and cpu-speed are setup before relocation */
+	/* so we do _nothing_ here */
+
+	/* arch number of cerf PXA Board */
+	gd->bd->bi_arch_number = 139;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0xa0000100;
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	setenv("stdout", "serial");
+	setenv("stderr", "serial");
+	return 0;
+}
+
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+	gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
+	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
+
+	return 0;
+}

board/cerf250/config.mk

@@ -0,0 +1,5 @@
+#
+# Cerf board with PXA250 cpu
+#
+#
+TEXT_BASE = 0xa3080000

board/cerf250/flash.c

@@ -0,0 +1,431 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+/* Board support for 1 or 2 flash devices */
+#define FLASH_PORT_WIDTH32
+#undef FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)               __swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)               __swab32(x)
+#endif
+
+#define FPW	   FLASH_PORT_WIDTH
+#define FPWV   FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (FPW *addr, flash_info_t *info);
+static int write_data (flash_info_t *info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t *info);
+void inline spin_wheel (void);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		case 1:
+			flash_get_size ((FPW *) PHYS_FLASH_2, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_2, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect ( FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1,
+			&flash_info[0] );
+
+	flash_protect ( FLAG_PROTECT_SET,
+			CFG_ENV_ADDR,
+			CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0] );
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
+			info->protect[i] = 0;
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F128J3A:
+		printf ("28F128J3A\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW *addr, flash_info_t *info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);			/* no or unknown flash  */
+	}
+
+	mb ();
+	value = addr[1];			/* device ID        */
+
+	switch (value) {
+
+	case (FPW) INTEL_ID_28F128J3A:
+		info->flash_id += FLASH_28F128J3A;
+		info->sector_count = 128;
+		info->size = 0x02000000;
+		break;				/* => 16 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+			info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;		/* restore read mode */
+
+	return (info->size);
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+			info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	start = get_timer (0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;	/* clear status register */
+			*addr = (FPW) 0x00200020;	/* erase setup */
+			*addr = (FPW) 0x00D000D0;	/* erase confirm */
+
+			while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+				if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					*addr = (FPW) 0x00B000B0;	/* suspend erase     */
+					*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
+					rcode = 1;
+					break;
+				}
+			}
+
+			*addr = 0x00500050;	/* clear status register cmd.   */
+			*addr = 0x00FF00FF;	/* resest to read mode          */
+
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t *info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%lx)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}

board/cerf250/memsetup.S

@@ -0,0 +1,411 @@
+/*
+ * Most of this taken from Redboot hal_platform_setup.h with cleanup
+ *
+ * NOTE: I haven't clean this up considerably, just enough to get it
+ * running. See hal_platform_setup.h for the source. See
+ * board/cradle/memsetup.S for another PXA250 setup that is
+ * much cleaner.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+
+DRAM_SIZE:  .long   CFG_DRAM_SIZE
+
+/* wait for coprocessor write complete */
+   .macro CPWAIT reg
+   mrc  p15,0,\reg,c2,c0,0
+   mov  \reg,\reg
+   sub  pc,pc,#4
+   .endm
+
+
+/*
+ * 	Memory setup
+ */
+
+.globl memsetup
+memsetup:
+
+	/* Set up GPIO pins first ----------------------------------------- */
+
+	ldr		r0,	=GPSR0
+	ldr		r1,	=CFG_GPSR0_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPSR1
+	ldr		r1,	=CFG_GPSR1_VAL
+	str		r1,  [r0]
+
+	ldr		r0,	=GPSR2
+	ldr		r1,	=CFG_GPSR2_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPCR0
+	ldr		r1,	=CFG_GPCR0_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPCR1
+	ldr		r1,	=CFG_GPCR1_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPCR2
+	ldr		r1,	=CFG_GPCR2_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPDR0
+	ldr		r1,	=CFG_GPDR0_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPDR1
+	ldr		r1,	=CFG_GPDR1_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GPDR2
+	ldr		r1,	=CFG_GPDR2_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GAFR0_L
+	ldr		r1,	=CFG_GAFR0_L_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GAFR0_U
+	ldr		r1,	=CFG_GAFR0_U_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GAFR1_L
+	ldr		r1,	=CFG_GAFR1_L_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GAFR1_U
+	ldr		r1,	=CFG_GAFR1_U_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GAFR2_L
+	ldr		r1,	=CFG_GAFR2_L_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=GAFR2_U
+	ldr		r1,	=CFG_GAFR2_U_VAL
+	str		r1,	[r0]
+
+	ldr		r0,	=PSSR				/* enable GPIO pins */
+	ldr		r1,	=CFG_PSSR_VAL
+	str		r1,	[r0]
+
+	/* ---------------------------------------------------------------- */
+	/* Enable memory interface                                          */
+	/*                                                                  */
+	/* The sequence below is based on the recommended init steps        */
+	/* detailed in the Intel PXA250 Operating Systems Developers Guide, */
+	/* Chapter 10.                                                      */
+	/* ---------------------------------------------------------------- */
+
+	/* ---------------------------------------------------------------- */
+	/* Step 1: Wait for at least 200 microsedonds to allow internal     */
+	/*         clocks to settle. Only necessary after hard reset...     */
+	/*         FIXME: can be optimized later                            */
+	/* ---------------------------------------------------------------- */
+
+	ldr		r3,	=OSCR			/* reset the OS Timer Count to zero */
+	mov 	r2,	#0
+	str 	r2,	[r3]
+	ldr 	r4,	=0x300				/* really 0x2E1 is about 200usec,   */
+							/* so 0x300 should be plenty        */
+1:
+	ldr 	r2,	[r3]
+	cmp 	r4,	r2
+	bgt 	1b
+
+mem_init:
+
+	ldr  	r1,	=MEMC_BASE		/* get memory controller base addr. */
+
+	/* ---------------------------------------------------------------- */
+	/* Step 2a: Initialize Asynchronous static memory controller        */
+	/* ---------------------------------------------------------------- */
+
+	/* MSC registers: timing, bus width, mem type                       */
+
+	/* MSC0: nCS(0,1)                                                   */
+	ldr  	r2,	=CFG_MSC0_VAL
+	str  	r2,	[r1, #MSC0_OFFSET]
+	ldr  	r2,	[r1, #MSC0_OFFSET]	/* read back to ensure      */
+						/* that data latches        */
+	/* MSC1: nCS(2,3)                                                   */
+	ldr  	r2,	=CFG_MSC1_VAL
+	str  	r2,	[r1, #MSC1_OFFSET]
+	ldr  	r2,	[r1, #MSC1_OFFSET]
+
+	/* MSC2: nCS(4,5)                                                   */
+	ldr  	r2,	=CFG_MSC2_VAL
+	str  	r2,	[r1, #MSC2_OFFSET]
+	ldr  	r2,	[r1, #MSC2_OFFSET]
+
+	/* ---------------------------------------------------------------- */
+	/* Step 2b: Initialize Card Interface                               */
+	/* ---------------------------------------------------------------- */
+
+	/* MECR: Memory Expansion Card Register                             */
+	ldr  	r2,	=CFG_MECR_VAL
+	str  	r2,	[r1, #MECR_OFFSET]
+	ldr	 	r2,	[r1, #MECR_OFFSET]
+
+	/* MCMEM0: Card Interface slot 0 timing                             */
+	ldr  	r2,	=CFG_MCMEM0_VAL
+	str  	r2,	[r1, #MCMEM0_OFFSET]
+	ldr	 	r2,	[r1, #MCMEM0_OFFSET]
+
+	/* MCMEM1: Card Interface slot 1 timing                             */
+	ldr  	r2,	=CFG_MCMEM1_VAL
+	str  	r2,	[r1, #MCMEM1_OFFSET]
+	ldr	 	r2,	[r1, #MCMEM1_OFFSET]
+
+	/* MCATT0: Card Interface Attribute Space Timing, slot 0            */
+	ldr  	r2,	=CFG_MCATT0_VAL
+	str  	r2,	[r1, #MCATT0_OFFSET]
+	ldr	 	r2,	[r1, #MCATT0_OFFSET]
+
+	/* MCATT1: Card Interface Attribute Space Timing, slot 1            */
+	ldr  	r2, =CFG_MCATT1_VAL
+	str  	r2, [r1, #MCATT1_OFFSET]
+	ldr	 	r2,	[r1, #MCATT1_OFFSET]
+
+	/* MCIO0: Card Interface I/O Space Timing, slot 0                   */
+	ldr  	r2, =CFG_MCIO0_VAL
+	str  	r2, [r1, #MCIO0_OFFSET]
+	ldr	 	r2,	[r1, #MCIO0_OFFSET]
+
+	/* MCIO1: Card Interface I/O Space Timing, slot 1                   */
+	ldr  	r2, =CFG_MCIO1_VAL
+	str  	r2, [r1, #MCIO1_OFFSET]
+	ldr	 	r2,	[r1, #MCIO1_OFFSET]
+
+	/* ---------------------------------------------------------------- */
+	/* Step 2c: Write FLYCNFG  FIXME: what's that???                    */
+	/* ---------------------------------------------------------------- */
+
+
+	/* ---------------------------------------------------------------- */
+	/* Step 2d: Initialize Timing for Sync Memory (SDCLK0)              */
+	/* ---------------------------------------------------------------- */
+
+	/* Before accessing MDREFR we need a valid DRI field, so we set     */
+	/* this to power on defaults + DRI field, set SDRAM clocks free running */
+
+	ldr  	r3, =CFG_MDREFR_VAL
+	ldr  	r2, =0xFFF
+	and  	r3, r3,  r2
+
+	ldr	 	r0,	[r1, #MDREFR_OFFSET]
+	bic	 	r0, r0, r2
+	bic	 	r0, r0, #(MDREFR_K0FREE|MDREFR_K1FREE|MDREFR_K2FREE)
+	orr	 	r0, r0, r3
+
+	str		r0,	[r1, #MDREFR_OFFSET]	/* write back MDREFR        */
+
+
+	/* ---------------------------------------------------------------- */
+	/* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */
+	/* ---------------------------------------------------------------- */
+
+	/* Initialize SXCNFG register. Assert the enable bits               */
+
+	/* Write SXMRS to cause an MRS command to all enabled banks of      */
+	/* synchronous static memory. Note that SXLCR need not be written   */
+	/* at this time.                                                    */
+
+	/* FIXME: we use async mode for now                                 */
+
+
+	/* ---------------------------------------------------------------- */
+	/* Step 4: Initialize SDRAM                                         */
+	/* ---------------------------------------------------------------- */
+
+	/* set MDREFR according to user define with exception of a few bits */
+
+	ldr     r4, =CFG_MDREFR_VAL
+	ldr		r2, =(MDREFR_K0RUN|MDREFR_K0DB2|MDREFR_K1RUN|MDREFR_K1DB2|\
+					MDREFR_K2RUN |MDREFR_K2DB2)
+	and		r4, r4, r2
+	bic		r0,	r0,	r2
+	orr		r0, r0, r4
+
+	str     r0, [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
+	ldr     r0, [r1, #MDREFR_OFFSET]
+
+	/* Step 4b: de-assert MDREFR:SLFRSH.                                */
+
+	bic		r0, r0,	#(MDREFR_SLFRSH)
+	str     r0, [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
+	ldr     r0, [r1, #MDREFR_OFFSET]
+
+
+	/* Step 4c: assert MDREFR:E1PIN and E0PIO as desired, set KXFREE  */
+
+	ldr     r4, =CFG_MDREFR_VAL
+	ldr		r2, =(MDREFR_E0PIN|MDREFR_E1PIN|MDREFR_K0FREE| \
+					MDREFR_K1FREE | MDREFR_K2FREE)
+	and		r4, r4, r2
+	orr		r0, r0, r4
+	str     r0, [r1, #MDREFR_OFFSET]    /* write back MDREFR        */
+	ldr     r0, [r1, #MDREFR_OFFSET]
+
+
+	/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to  */
+	/*          configure but not enable each SDRAM partition pair.     */
+
+	ldr		r4,	=CFG_MDCNFG_VAL
+	bic		r4,	r4,	#(MDCNFG_DE0|MDCNFG_DE1)
+	bic		r4, r4,	#(MDCNFG_DE2|MDCNFG_DE3)
+	str     r4, [r1, #MDCNFG_OFFSET]	/* write back MDCNFG        */
+	ldr     r4, [r1, #MDCNFG_OFFSET]
+
+
+	/* Step 4e: Wait for the clock to the SDRAMs to stabilize,          */
+	/*          100..200 <20>sec.                                          */
+
+	ldr 	r3, =OSCR			/* reset the OS Timer Count to zero */
+	mov 	r2, #0
+	str 	r2, [r3]
+	ldr 	r4, =0x300			/* really 0x2E1 is about 200usec,   */
+						/* so 0x300 should be plenty        */
+1:
+	ldr 	r2, [r3]
+	cmp 	r4, r2
+	bgt 	1b
+
+
+	/* Step 4f: Trigger a number (usually 8) refresh cycles by          */
+	/*          attempting non-burst read or write accesses to disabled */
+	/*          SDRAM, as commonly specified in the power up sequence   */
+	/*          documented in SDRAM data sheets. The address(es) used   */
+	/*          for this purpose must not be cacheable.                 */
+
+	ldr		r3,	=CFG_DRAM_BASE
+.rept 8
+	str		r2,	[r3]
+.endr
+
+	/* Step 4g: Write MDCNFG with enable bits asserted                  */
+	/*          (MDCNFG:DEx set to 1).                                  */
+
+	ldr     r3, [r1, #MDCNFG_OFFSET]
+	orr	r3,	r3,	#(MDCNFG_DE0|MDCNFG_DE1)
+	str     r3, [r1, #MDCNFG_OFFSET]
+
+	/* Step 4h: Write MDMRS.                                            */
+
+	ldr     r2, =CFG_MDMRS_VAL
+	str     r2, [r1, #MDMRS_OFFSET]
+
+
+	/* We are finished with Intel's memory controller initialisation    */
+
+
+	/* ---------------------------------------------------------------- */
+	/* Disable (mask) all interrupts at interrupt controller            */
+	/* ---------------------------------------------------------------- */
+
+initirqs:
+
+	mov     r1, #0		/* clear int. level register (IRQ, not FIQ) */
+	ldr     r2, =ICLR
+	str     r1, [r2]
+
+	ldr     r2, =ICMR	/* mask all interrupts at the controller    */
+	str     r1, [r2]
+
+
+	/* ---------------------------------------------------------------- */
+	/* Clock initialisation                                             */
+	/* ---------------------------------------------------------------- */
+
+initclks:
+
+	/* Disable the peripheral clocks, and set the core clock frequency  */
+
+	/* Turn Off ALL on-chip peripheral clocks for re-configuration      */
+	/* Note: See label 'ENABLECLKS' for the re-enabling                 */
+	ldr     r1, =CKEN
+	mov     r2, #0
+	str     r2, [r1]
+
+
+	/* default value in case no valid rotary switch setting is found    */
+	ldr     r2, =(CCCR_L27|CCCR_M2|CCCR_N10)  /* DEFAULT: {200/200/100} */
+
+	/* ... and write the core clock config register                     */
+	ldr     r1, =CCCR
+	str     r2, [r1]
+
+#ifdef RTC
+	/* enable the 32Khz oscillator for RTC and PowerManager             */
+
+	ldr     r1, =OSCC
+	mov     r2, #OSCC_OON
+	str     r2, [r1]
+
+	/* NOTE:  spin here until OSCC.OOK get set, meaning the PLL         */
+	/* has settled.                                                     */
+60:
+	ldr     r2, [r1]
+	ands    r2, r2, #1
+	beq     60b
+#endif
+
+	/* ---------------------------------------------------------------- */
+	/*                                                                  */
+	/* ---------------------------------------------------------------- */
+
+	/* Save SDRAM size */
+    ldr     r1, =DRAM_SIZE
+	str   	r8, [r1]
+
+	/* Interrupt init: Mask all interrupts                              */
+    ldr		r0,	=ICMR /* enable no sources */
+	mov 	r1,	#0
+    str 	r1,	[r0]
+
+	/* FIXME */
+
+#define NODEBUG
+#ifdef NODEBUG
+	/*Disable software and data breakpoints */
+	mov		r0,#0
+	mcr		p15,0,r0,c14,c8,0  /* ibcr0 */
+	mcr		p15,0,r0,c14,c9,0  /* ibcr1 */
+	mcr		p15,0,r0,c14,c4,0  /* dbcon */
+
+	/*Enable all debug functionality */
+	mov		r0,#0x80000000
+	mcr		p14,0,r0,c10,c0,0  /* dcsr */
+
+#endif
+
+	/* ---------------------------------------------------------------- */
+	/* End memsetup                                                     */
+	/* ---------------------------------------------------------------- */
+
+endmemsetup:
+
+    mov     pc,	lr

board/cerf250/u-boot.lds

@@ -21,23 +21,35 @@
  * MA 02111-1307 USA
  */
 
-/****************************************************************************
- * FLASH Memory Map as used by FADS Monitor:
- *
- *                          Start Address    Length
- * +-----------------------+ 0xFE00_0000     Start of Flash -----------------
- * | MON8xx code           | 0xFE00_0100     Reset Vector
- * +-----------------------+ 0xFE0?_????
- * | (unused)              |
- * +-----------------------+
- * | 			   |
- * +-----------------------+
- * | 			   |
- * +-----------------------+
- * | 			   |
- * +-----------------------+
- * | 			   |
- * +=======================+
- * | 			   |
- * | ...                   |
- *****************************************************************************/
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/pxa/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/cogent/mb.c

@@ -235,7 +235,7 @@ int misc_init_f (void)
 
 long int initdram (int board_type)
 {
-#if CONFIG_CMA111
+#ifdef CONFIG_CMA111
 	return (32L * 1024L * 1024L);
 #else
 	unsigned char dipsw_val;

board/cpc45/cpc45.c

@@ -25,6 +25,7 @@
 #include <mpc824x.h>
 #include <asm/processor.h>
 #include <pci.h>
+#include <i2c.h>
 
 int sysControlDisplay(int digit, uchar ascii_code);
 extern void Plx9030Init(void);
@@ -49,7 +50,7 @@ int checkboard(void)
 	ulong busfreq  = get_bus_freq(0);
 	char  buf[32];
 
-	printf("CPC45 ");
+	puts ("CPC45  ");
 /*
 	printf("Revision %d ", revision);
 */
@@ -58,46 +59,134 @@ int checkboard(void)
 	return 0;
 }
 
-long int initdram(int board_type)
+long int initdram (int board_type)
 {
-	long size;
-	long new_bank0_end;
-	long mear1;
-	long emear1;
+	int m, row, col, bank, i, ref;
+	unsigned long start, end;
+	uint32_t mccr1, mccr2;
+	uint32_t mear1 = 0, emear1 = 0, msar1 = 0, emsar1 = 0;
+	uint32_t mear2 = 0, emear2 = 0, msar2 = 0, emsar2 = 0;
+	uint8_t mber = 0;
+	unsigned int tmp;
 
-	size = get_ram_size(CFG_SDRAM_BASE, CFG_MAX_RAM_SIZE);
+	i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
 
-	new_bank0_end = size - 1;
-	mear1 = mpc824x_mpc107_getreg(MEAR1);
-	emear1 = mpc824x_mpc107_getreg(EMEAR1);
-	mear1 = (mear1  & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
-	emear1 = (emear1 & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
-	mpc824x_mpc107_setreg(MEAR1, mear1);
-	mpc824x_mpc107_setreg(EMEAR1, emear1);
+	if (i2c_reg_read (0x50, 2) != 0x04)
+		return 0;	/* Memory type */
 
-	return (size);
+	m = i2c_reg_read (0x50, 5);	/* # of physical banks */
+	row = i2c_reg_read (0x50, 3);	/* # of rows */
+	col = i2c_reg_read (0x50, 4);	/* # of columns */
+	bank = i2c_reg_read (0x50, 17);	/* # of logical banks */
+	ref  = i2c_reg_read (0x50, 12);	/* refresh rate / type */
+
+	CONFIG_READ_WORD(MCCR1, mccr1);
+	mccr1 &= 0xffff0000;
+
+	CONFIG_READ_WORD(MCCR2, mccr2);
+	mccr2 &= 0xffff0000;
+
+	start = CFG_SDRAM_BASE;
+	end = start + (1 << (col + row + 3) ) * bank - 1;
+
+	for (i = 0; i < m; i++) {
+		mccr1 |= ((row == 13)? 2 : (bank == 4)? 0 : 3) << i * 2;
+		if (i < 4) {
+			msar1  |= ((start >> 20) & 0xff) << i * 8;
+			emsar1 |= ((start >> 28) & 0xff) << i * 8;
+			mear1  |= ((end >> 20) & 0xff) << i * 8;
+			emear1 |= ((end >> 28) & 0xff) << i * 8;
+		} else {
+			msar2  |= ((start >> 20) & 0xff) << (i-4) * 8;
+			emsar2 |= ((start >> 28) & 0xff) << (i-4) * 8;
+			mear2  |= ((end >> 20) & 0xff) << (i-4) * 8;
+			emear2 |= ((end >> 28) & 0xff) << (i-4) * 8;
+		}
+		mber |= 1 << i;
+		start += (1 << (col + row + 3) ) * bank;
+		end += (1 << (col + row + 3) ) * bank;
+	}
+	for (; i < 8; i++) {
+		if (i < 4) {
+			msar1  |= 0xff << i * 8;
+			emsar1 |= 0x30 << i * 8;
+			mear1  |= 0xff << i * 8;
+			emear1 |= 0x30 << i * 8;
+		} else {
+			msar2  |= 0xff << (i-4) * 8;
+			emsar2 |= 0x30 << (i-4) * 8;
+			mear2  |= 0xff << (i-4) * 8;
+			emear2 |= 0x30 << (i-4) * 8;
+		}
+	}
+
+	switch(ref) {
+		case 0x00:
+		case 0x80:
+			tmp = get_bus_freq(0) / 1000000 * 15625 / 1000 - 22;
+			break;
+		case 0x01:
+		case 0x81:
+			tmp = get_bus_freq(0) / 1000000 * 3900 / 1000 - 22;
+			break;
+		case 0x02:
+		case 0x82:
+			tmp = get_bus_freq(0) / 1000000 * 7800 / 1000 - 22;
+			break;
+		case 0x03:
+		case 0x83:
+			tmp = get_bus_freq(0) / 1000000 * 31300 / 1000 - 22;
+			break;
+		case 0x04:
+		case 0x84:
+			tmp = get_bus_freq(0) / 1000000 * 62500 / 1000 - 22;
+			break;
+		case 0x05:
+		case 0x85:
+			tmp = get_bus_freq(0) / 1000000 * 125000 / 1000 - 22;
+			break;
+		default:
+			tmp = 0x512;
+			break;
+	}
+
+	CONFIG_WRITE_WORD(MCCR1, mccr1);
+	CONFIG_WRITE_WORD(MCCR2, tmp << MCCR2_REFINT_SHIFT);
+	CONFIG_WRITE_WORD(MSAR1, msar1);
+	CONFIG_WRITE_WORD(EMSAR1, emsar1);
+	CONFIG_WRITE_WORD(MEAR1, mear1);
+	CONFIG_WRITE_WORD(EMEAR1, emear1);
+	CONFIG_WRITE_WORD(MSAR2, msar2);
+	CONFIG_WRITE_WORD(EMSAR2, emsar2);
+	CONFIG_WRITE_WORD(MEAR2, mear2);
+	CONFIG_WRITE_WORD(EMEAR2, emear2);
+	CONFIG_WRITE_BYTE(MBER, mber);
+
+	return (1 << (col + row + 3) ) * bank * m;
 }
 
+
 /*
  * Initialize PCI Devices, report devices found.
  */
-#ifndef CONFIG_PCI_PNP
 
-static struct pci_config_table pci_sandpoint_config_table[] = {
-	{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
+static struct pci_config_table pci_cpc45_config_table[] = {
+#ifndef CONFIG_PCI_PNP
+	{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0F, PCI_ANY_ID,
 	  pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
 				       PCI_ENET0_MEMADDR,
 				       PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
+	{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0D, PCI_ANY_ID,
+	  pci_cfgfunc_config_device, { PCI_PLX9030_IOADDR,
+				       PCI_PLX9030_MEMADDR,
+				       PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
+#endif /*CONFIG_PCI_PNP*/
 	{ }
 };
-#endif
-
 
 struct pci_controller hose = {
 #ifndef CONFIG_PCI_PNP
-	config_table: pci_sandpoint_config_table,
+	config_table: pci_cpc45_config_table,
 #endif
 };
 
@@ -108,6 +197,9 @@ void pci_init_board(void)
 	/* init PCI_to_LOCAL Bus BRIDGE */
 	Plx9030Init();
 
+	/* Clear Display */
+	DISP_CWORD = 0x0;
+
 	sysControlDisplay(0,' ');
 	sysControlDisplay(1,'C');
 	sysControlDisplay(2,'P');
@@ -130,16 +222,14 @@ void pci_init_board(void)
 * RETURNS: NA
 */
 
-int sysControlDisplay
-    (
-    int digit, 			/* number of digit 0..7 */
-    uchar ascii_code		/* ASCII code */
-    )
+int sysControlDisplay (int digit,	/* number of digit 0..7 */
+		       uchar ascii_code	/* ASCII code */
+		      )
 {
 	if ((digit < 0) || (digit > 7))
 		return (-1);
 
-	*((volatile uchar*)(DISP_CHR_RAM + digit)) = ascii_code;
+	*((volatile uchar *) (DISP_CHR_RAM + digit)) = ascii_code;
 
 	return (0);
 }

board/cpc45/flash.c

@@ -41,12 +41,12 @@
 #define MAIN_SECT_SIZE  0x40000
 #define PARAM_SECT_SIZE 0x8000
 
-flash_info_t    flash_info[CFG_MAX_FLASH_BANKS];
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
 
-static int write_data (flash_info_t *info, ulong dest, ulong *data);
-static void write_via_fpu(vu_long *addr, ulong *data);
-static __inline__ unsigned long get_msr(void);
-static __inline__ void set_msr(unsigned long msr);
+static int write_data (flash_info_t * info, ulong dest, ulong * data);
+static void write_via_fpu (vu_long * addr, ulong * data);
+static __inline__ unsigned long get_msr (void);
+static __inline__ void set_msr (unsigned long msr);
 
 /*---------------------------------------------------------------------*/
 #undef	DEBUG_FLASH
@@ -62,102 +62,132 @@ static __inline__ void set_msr(unsigned long msr);
 /*-----------------------------------------------------------------------
  */
 
-unsigned long flash_init(void)
+unsigned long flash_init (void)
 {
-    int i, j;
-    ulong size = 0;
-    uchar tempChar;
+	int i, j;
+	ulong size = 0;
+	uchar tempChar;
+	vu_long *tmpaddr;
 
-   /* Enable flash writes on CPC45 */
+	/* Enable flash writes on CPC45 */
 
-    tempChar = BOARD_CTRL;
+	tempChar = BOARD_CTRL;
 
-    tempChar |= (B_CTRL_FWPT_1 | B_CTRL_FWRE_1);
+	tempChar |= (B_CTRL_FWPT_1 | B_CTRL_FWRE_1);
 
-    tempChar &= ~(B_CTRL_FWPT_0 | B_CTRL_FWRE_0);
+	tempChar &= ~(B_CTRL_FWPT_0 | B_CTRL_FWRE_0);
 
-    BOARD_CTRL = tempChar;
+	BOARD_CTRL = tempChar;
+
+	__asm__ volatile ("sync\n eieio");
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		vu_long *addr = (vu_long *) (CFG_FLASH_BASE + i * FLASH_BANK_SIZE);
+
+		addr[0] = 0x00900090;
+
+		__asm__ volatile ("sync\n eieio");
+
+		udelay (100);
+
+		DEBUGF ("Flash bank # %d:\n"
+			"\tManuf. ID @ 0x%08lX: 0x%08lX\n"
+			"\tDevice ID @ 0x%08lX: 0x%08lX\n",
+			i,
+			(ulong) (&addr[0]), addr[0],
+			(ulong) (&addr[2]), addr[2]);
 
 
-    for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
-	vu_long *addr = (vu_long *)(CFG_FLASH_BASE + i * FLASH_BANK_SIZE);
+		if ((addr[0] == addr[1]) && (addr[0] == INTEL_MANUFACT) &&
+		    (addr[2] == addr[3]) && (addr[2] == INTEL_ID_28F160F3T)) {
 
-	addr[0] = 0x00900090;
+			flash_info[i].flash_id =
+				(FLASH_MAN_INTEL & FLASH_VENDMASK) |
+				(INTEL_ID_28F160F3T & FLASH_TYPEMASK);
 
-	DEBUGF ("Flash bank # %d:\n"
-		"\tManuf. ID @ 0x%08lX: 0x%08lX\n"
-		"\tDevice ID @ 0x%08lX: 0x%08lX\n",
-		i,
-		(ulong)(&addr[0]), addr[0],
-		(ulong)(&addr[2]), addr[2]);
+		} else if ((addr[0] == addr[1]) && (addr[0] == INTEL_MANUFACT)
+			 && (addr[2] == addr[3])
+			 && (addr[2] == INTEL_ID_28F160C3T)) {
 
+			flash_info[i].flash_id =
+				(FLASH_MAN_INTEL & FLASH_VENDMASK) |
+				(INTEL_ID_28F160C3T & FLASH_TYPEMASK);
 
-	if ((addr[0] == addr[1]) && (addr[0] == INTEL_MANUFACT) &&
-	    (addr[2] == addr[3]) && (addr[2] == INTEL_ID_28F160F3T))
-	{
-
-	    flash_info[i].flash_id = (FLASH_MAN_INTEL & FLASH_VENDMASK) |
-				     (INTEL_ID_28F160F3T & FLASH_TYPEMASK);
-
-	} else {
-	    flash_info[i].flash_id = FLASH_UNKNOWN;
-	    addr[0] = 0xFFFFFFFF;
-	    goto Done;
-	}
-
-	DEBUGF ("flash_id = 0x%08lX\n", flash_info[i].flash_id);
-
-	addr[0] = 0xFFFFFFFF;
-
-	flash_info[i].size = FLASH_BANK_SIZE;
-	flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
-	memset(flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
-	for (j = 0; j < flash_info[i].sector_count; j++) {
-		if (j > 30) {
-			flash_info[i].start[j] = CFG_FLASH_BASE +
-						 i * FLASH_BANK_SIZE +
-						 (MAIN_SECT_SIZE * 31) + (j - 31) * PARAM_SECT_SIZE;
 		} else {
-			flash_info[i].start[j] = CFG_FLASH_BASE +
-						 i * FLASH_BANK_SIZE +
-						 j * MAIN_SECT_SIZE;
+			flash_info[i].flash_id = FLASH_UNKNOWN;
+			addr[0] = 0xFFFFFFFF;
+			goto Done;
 		}
-	}
-	size += flash_info[i].size;
-    }
 
-    /* Protect monitor and environment sectors
-     */
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
+		DEBUGF ("flash_id = 0x%08lX\n", flash_info[i].flash_id);
+
+		addr[0] = 0xFFFFFFFF;
+
+		flash_info[i].size = FLASH_BANK_SIZE;
+		flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
+		memset (flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
+		for (j = 0; j < flash_info[i].sector_count; j++) {
+			if (j > 30) {
+				flash_info[i].start[j] = CFG_FLASH_BASE +
+					i * FLASH_BANK_SIZE +
+					(MAIN_SECT_SIZE * 31) + (j -
+								 31) *
+					PARAM_SECT_SIZE;
+			} else {
+				flash_info[i].start[j] = CFG_FLASH_BASE +
+					i * FLASH_BANK_SIZE +
+					j * MAIN_SECT_SIZE;
+			}
+		}
+
+		/* unlock sectors, if 160C3T */
+
+		for (j = 0; j < flash_info[i].sector_count; j++) {
+			tmpaddr = (vu_long *) flash_info[i].start[j];
+
+			if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			    (INTEL_ID_28F160C3T & FLASH_TYPEMASK)) {
+				tmpaddr[0] = 0x00600060;
+				tmpaddr[0] = 0x00D000D0;
+				tmpaddr[1] = 0x00600060;
+				tmpaddr[1] = 0x00D000D0;
+			}
+		}
+
+		size += flash_info[i].size;
+
+		addr[0] = 0x00FF00FF;
+		addr[1] = 0x00FF00FF;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE + FLASH_BANK_SIZE
-    flash_protect(FLAG_PROTECT_SET,
-	      CFG_MONITOR_BASE,
-	      CFG_MONITOR_BASE + monitor_flash_len - 1,
-	      &flash_info[1]);
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_MONITOR_BASE,
+		       CFG_MONITOR_BASE + monitor_flash_len - 1,
+		       &flash_info[1]);
 #else
-    flash_protect(FLAG_PROTECT_SET,
-	      CFG_MONITOR_BASE,
-	      CFG_MONITOR_BASE + monitor_flash_len - 1,
-	      &flash_info[0]);
-#endif
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_MONITOR_BASE,
+		       CFG_MONITOR_BASE + monitor_flash_len - 1,
+		       &flash_info[0]);
 #endif
 
 #if (CFG_ENV_IS_IN_FLASH == 1) && defined(CFG_ENV_ADDR)
 #if CFG_ENV_ADDR >= CFG_FLASH_BASE + FLASH_BANK_SIZE
-    flash_protect(FLAG_PROTECT_SET,
-	      CFG_ENV_ADDR,
-	      CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
-	      &flash_info[1]);
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[1]);
 #else
-    flash_protect(FLAG_PROTECT_SET,
-	      CFG_ENV_ADDR,
-	      CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
-	      &flash_info[0]);
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
 #endif
 #endif
 
 Done:
-    return size;
+	return size;
 }
 
 /*-----------------------------------------------------------------------
@@ -179,6 +209,11 @@ void flash_print_info (flash_info_t * info)
 	case (INTEL_ID_28F160F3T & FLASH_TYPEMASK):
 		printf ("28F160F3T (16Mbit)\n");
 		break;
+
+	case (INTEL_ID_28F160C3T & FLASH_TYPEMASK):
+		printf ("28F160C3T (16Mbit)\n");
+		break;
+
 	default:
 		printf ("Unknown Chip Type 0x%04x\n", i);
 		goto Done;
@@ -186,7 +221,7 @@ void flash_print_info (flash_info_t * info)
 	}
 
 	printf ("  Size: %ld MB in %d Sectors\n",
-			info->size >> 20, info->sector_count);
+		info->size >> 20, info->sector_count);
 
 	printf ("  Sector Start Addresses:");
 	for (i = 0; i < info->sector_count; i++) {
@@ -194,7 +229,7 @@ void flash_print_info (flash_info_t * info)
 			printf ("\n   ");
 		}
 		printf (" %08lX%s", info->start[i],
-				info->protect[i] ? " (RO)" : "     ");
+			info->protect[i] ? " (RO)" : "     ");
 	}
 	printf ("\n");
 
@@ -205,7 +240,7 @@ Done:
 /*-----------------------------------------------------------------------
  */
 
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
+int flash_erase (flash_info_t * info, int s_first, int s_last)
 {
 	int flag, prot, sect;
 	ulong start, now, last;
@@ -229,33 +264,32 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 	}
 
 	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
+	for (sect = s_first; sect <= s_last; ++sect) {
 		if (info->protect[sect]) {
 			prot++;
 		}
 	}
 
 	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
+		printf ("- Warning: %d protected sectors will not be erased!\n", prot);
 	} else {
 		printf ("\n");
 	}
 
 	start = get_timer (0);
-	last  = start;
+	last = start;
 	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last; sect++) {
+	for (sect = s_first; sect <= s_last; sect++) {
 		if (info->protect[sect] == 0) {	/* not protected */
-			vu_long *addr = (vu_long *)(info->start[sect]);
+			vu_long *addr = (vu_long *) (info->start[sect]);
 
 			DEBUGF ("Erase sect %d @ 0x%08lX\n",
-				sect, (ulong)addr);
+				sect, (ulong) addr);
 
 			/* Disable interrupts which might cause a timeout
 			 * here.
 			 */
-			flag = disable_interrupts();
+			flag = disable_interrupts ();
 
 			addr[0] = 0x00500050;	/* clear status register */
 			addr[0] = 0x00200020;	/* erase setup */
@@ -267,23 +301,23 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 
 			/* re-enable interrupts if necessary */
 			if (flag)
-				enable_interrupts();
+				enable_interrupts ();
 
 			/* wait at least 80us - let's wait 1 ms */
 			udelay (1000);
 
 			while (((addr[0] & 0x00800080) != 0x00800080) ||
-			       ((addr[1] & 0x00800080) != 0x00800080) ) {
-				if ((now=get_timer(start)) >
-					   CFG_FLASH_ERASE_TOUT) {
+			       ((addr[1] & 0x00800080) != 0x00800080)) {
+				if ((now = get_timer (start)) >
+				    CFG_FLASH_ERASE_TOUT) {
 					printf ("Timeout\n");
-					addr[0] = 0x00B000B0; /* suspend erase */
-					addr[0] = 0x00FF00FF; /* to read mode  */
+					addr[0] = 0x00B000B0;	/* suspend erase */
+					addr[0] = 0x00FF00FF;	/* to read mode  */
 					return 1;
 				}
 
 				/* show that we're waiting */
-				if ((now - last) > 1000) {  /* every second  */
+				if ((now - last) > 1000) {	/* every second  */
 					putc ('.');
 					last = now;
 				}
@@ -306,7 +340,7 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 
 #define	FLASH_WIDTH	8	/* flash bus width in bytes */
 
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
 {
 	ulong wp, cp, msr;
 	int l, rc, i;
@@ -315,16 +349,16 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	ulong *datal = &data[1];
 
 	DEBUGF ("Flash write_buff: @ 0x%08lx, src 0x%08lx len %ld\n",
-		addr, (ulong)src, cnt);
+		addr, (ulong) src, cnt);
 
 	if (info->flash_id == FLASH_UNKNOWN) {
 		return 4;
 	}
 
-	msr = get_msr();
-	set_msr(msr | MSR_FP);
+	msr = get_msr ();
+	set_msr (msr | MSR_FP);
 
-	wp = (addr & ~(FLASH_WIDTH-1));	/* get lower aligned address */
+	wp = (addr & ~(FLASH_WIDTH - 1));	/* get lower aligned address */
 
 	/*
 	 * handle unaligned start bytes
@@ -335,39 +369,35 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 		for (i = 0, cp = wp; i < l; i++, cp++) {
 			if (i >= 4) {
 				*datah = (*datah << 8) |
-						((*datal & 0xFF000000) >> 24);
+					((*datal & 0xFF000000) >> 24);
 			}
 
-			*datal = (*datal << 8) | (*(uchar *)cp);
+			*datal = (*datal << 8) | (*(uchar *) cp);
 		}
 		for (; i < FLASH_WIDTH && cnt > 0; ++i) {
-			char tmp;
-
-			tmp = *src;
-
-			src++;
+			char tmp = *src++;
 
 			if (i >= 4) {
 				*datah = (*datah << 8) |
-						((*datal & 0xFF000000) >> 24);
+					((*datal & 0xFF000000) >> 24);
 			}
 
 			*datal = (*datal << 8) | tmp;
-
-			--cnt; ++cp;
+			--cnt;
+			++cp;
 		}
 
 		for (; cnt == 0 && i < FLASH_WIDTH; ++i, ++cp) {
 			if (i >= 4) {
 				*datah = (*datah << 8) |
-						((*datal & 0xFF000000) >> 24);
+					((*datal & 0xFF000000) >> 24);
 			}
 
-			*datal = (*datah << 8) | (*(uchar *)cp);
+			*datal = (*datah << 8) | (*(uchar *) cp);
 		}
 
-		if ((rc = write_data(info, wp, data)) != 0) {
-			set_msr(msr);
+		if ((rc = write_data (info, wp, data)) != 0) {
+			set_msr (msr);
 			return (rc);
 		}
 
@@ -378,19 +408,19 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	 * handle FLASH_WIDTH aligned part
 	 */
 	while (cnt >= FLASH_WIDTH) {
-		*datah = *(ulong *)src;
-		*datal = *(ulong *)(src + 4);
-		if ((rc = write_data(info, wp, data)) != 0) {
-			set_msr(msr);
+		*datah = *(ulong *) src;
+		*datal = *(ulong *) (src + 4);
+		if ((rc = write_data (info, wp, data)) != 0) {
+			set_msr (msr);
 			return (rc);
 		}
-		wp  += FLASH_WIDTH;
+		wp += FLASH_WIDTH;
 		cnt -= FLASH_WIDTH;
 		src += FLASH_WIDTH;
 	}
 
 	if (cnt == 0) {
-		set_msr(msr);
+		set_msr (msr);
 		return (0);
 	}
 
@@ -399,31 +429,28 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	 */
 	*datah = *datal = 0;
 	for (i = 0, cp = wp; i < FLASH_WIDTH && cnt > 0; ++i, ++cp) {
-		char tmp;
-
-		tmp = *src;
-
-		src++;
+		char tmp = *src++;
 
 		if (i >= 4) {
-			*datah = (*datah << 8) | ((*datal & 0xFF000000) >> 24);
+			*datah = (*datah << 8) | ((*datal & 0xFF000000) >>
+						  24);
 		}
 
 		*datal = (*datal << 8) | tmp;
-
 		--cnt;
 	}
 
 	for (; i < FLASH_WIDTH; ++i, ++cp) {
 		if (i >= 4) {
-			*datah = (*datah << 8) | ((*datal & 0xFF000000) >> 24);
+			*datah = (*datah << 8) | ((*datal & 0xFF000000) >>
+						  24);
 		}
 
-		*datal = (*datal << 8) | (*(uchar *)cp);
+		*datal = (*datal << 8) | (*(uchar *) cp);
 	}
 
-	rc = write_data(info, wp, data);
-	set_msr(msr);
+	rc = write_data (info, wp, data);
+	set_msr (msr);
 
 	return (rc);
 }
@@ -434,32 +461,32 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
  * 1 - write timeout
  * 2 - Flash not erased
  */
-static int write_data (flash_info_t *info, ulong dest, ulong *data)
+static int write_data (flash_info_t * info, ulong dest, ulong * data)
 {
-	vu_long *addr = (vu_long *)dest;
+	vu_long *addr = (vu_long *) dest;
 	ulong start;
 	int flag;
 
 	/* Check if Flash is (sufficiently) erased */
 	if (((addr[0] & data[0]) != data[0]) ||
-	    ((addr[1] & data[1]) != data[1]) ) {
+	    ((addr[1] & data[1]) != data[1])) {
 		return (2);
 	}
 	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
+	flag = disable_interrupts ();
 
-	addr[0] = 0x00400040;		/* write setup */
-	write_via_fpu(addr, data);
+	addr[0] = 0x00400040;	/* write setup */
+	write_via_fpu (addr, data);
 
 	/* re-enable interrupts if necessary */
 	if (flag)
-		enable_interrupts();
+		enable_interrupts ();
 
 	start = get_timer (0);
 
 	while (((addr[0] & 0x00800080) != 0x00800080) ||
-	       ((addr[1] & 0x00800080) != 0x00800080) ) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
+	       ((addr[1] & 0x00800080) != 0x00800080)) {
+		if (get_timer (start) > CFG_FLASH_WRITE_TOUT) {
 			addr[0] = 0x00FF00FF;	/* restore read mode */
 			return (1);
 		}
@@ -472,22 +499,24 @@ static int write_data (flash_info_t *info, ulong dest, ulong *data)
 
 /*-----------------------------------------------------------------------
  */
-static void write_via_fpu(vu_long *addr, ulong *data)
+static void write_via_fpu (vu_long * addr, ulong * data)
 {
-	__asm__ __volatile__ ("lfd  1, 0(%0)" : : "r" (data));
-	__asm__ __volatile__ ("stfd 1, 0(%0)" : : "r" (addr));
+	__asm__ __volatile__ ("lfd  1, 0(%0)"::"r" (data));
+	__asm__ __volatile__ ("stfd 1, 0(%0)"::"r" (addr));
 }
+
 /*-----------------------------------------------------------------------
  */
-static __inline__ unsigned long get_msr(void)
+static __inline__ unsigned long get_msr (void)
 {
-    unsigned long msr;
+	unsigned long msr;
 
-    __asm__ __volatile__ ("mfmsr %0" : "=r" (msr) :);
-    return msr;
+	__asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
+
+	return msr;
 }
 
-static __inline__ void set_msr(unsigned long msr)
+static __inline__ void set_msr (unsigned long msr)
 {
-    __asm__ __volatile__ ("mtmsr %0" : : "r" (msr));
+	__asm__ __volatile__ ("mtmsr %0"::"r" (msr));
 }

board/cpu86/flash.c

@@ -41,10 +41,10 @@ ulong flash_int_get_size (volatile unsigned long *baseaddr,
 	info->sector_count = info->size = 0;
 	info->flash_id = FLASH_UNKNOWN;
 
-	/* Write query command sequence and test FLASH answer
+	/* Write identify command sequence and test FLASH answer
 	 */
-	baseaddr[0] = 0x00980098;
-	baseaddr[1] = 0x00980098;
+	baseaddr[0] = 0x00900090;
+	baseaddr[1] = 0x00900090;
 
 	flashtest_h = baseaddr[0];	/* manufacturer ID	*/
 	flashtest_l = baseaddr[1];

board/csb272/csb272.c

@@ -21,9 +21,8 @@
  * MA 02111-1307 USA
  */
 
-#include <asm/u-boot.h>
-#include <asm/processor.h>
 #include <common.h>
+#include <asm/processor.h>
 #include <i2c.h>
 #include <miiphy.h>
 #include <405gp_enet.h>
@@ -57,10 +56,10 @@ int pll_init(void)
 }
 
 /*
- * board_pre_init: do any preliminary board initialization
+ * board_early_init_f: do early board initialization
  *
  */
-int board_pre_init(void)
+int board_early_init_f(void)
 {
 	/* initialize PLL so UART, LCD, Ethernet clocked at correctly */
 	(void) get_clocks();

board/csb472/Makefile

@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+#OBJS	= $(BOARD).o flash.o
+#OBJS	= $(BOARD).o strataflash.o
+OBJS	= $(BOARD).o
+
+SOBJS	= init.o
+
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/csb472/config.mk

@@ -0,0 +1,36 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2004
+# Tolunay Orkun, NextIO Inc., torkun@nextio.com.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Cogent CSB472 board
+#
+
+LDFLAGS += $(LINKER_UNDEFS)
+
+TEXT_BASE := 0xFFFC0000
+#TEXT_BASE := 0x00100000
+
+PLATFORM_RELFLAGS := $(PLATFORM_RELFLAGS)

board/csb472/csb472.c

@@ -0,0 +1,141 @@
+/*
+ * (C) Copyright 2004
+ * Tolunay Orkun, Nextio Inc., torkun@nextio.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <405gp_enet.h>
+
+/*
+ * board_early_init_f: do early board initialization
+ *
+ */
+int board_early_init_f(void)
+{
+   /*-------------------------------------------------------------------------+
+   | Interrupt controller setup for the Walnut board.
+   | Note: IRQ 0-15  405GP internally generated; active high; level sensitive
+   |       IRQ 16    405GP internally generated; active low; level sensitive
+   |       IRQ 17-24 RESERVED
+   |       IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive
+   |       IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive
+   |       IRQ 27 (EXT IRQ 2) Not Used
+   |       IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive
+   |       IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
+   |       IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive
+   |       IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive
+   | Note for Walnut board:
+   |       An interrupt taken for the FPGA (IRQ 25) indicates that either
+   |       the Mouse, Keyboard, IRDA, or External Expansion caused the
+   |       interrupt. The FPGA must be read to determine which device
+   |       caused the interrupt. The default setting of the FPGA clears
+   |
+   +-------------------------------------------------------------------------*/
+
+	mtdcr (uicsr, 0xFFFFFFFF);   /* clear all ints */
+	mtdcr (uicer, 0x00000000);   /* disable all ints */
+	mtdcr (uiccr, 0x00000000);   /* set all to be non-critical */
+	mtdcr (uicpr, 0xFFFFFF83);   /* set int polarities */
+	mtdcr (uictr, 0x10000000);   /* set int trigger levels */
+	mtdcr (uicvcr, 0x00000001);  /* set vect base=0,INT0 highest priority */
+	mtdcr (uicsr, 0xFFFFFFFF);   /* clear all ints */
+
+	mtebc (epcr, 0xa8400000);   /* EBC always driven */
+
+	return 0; /* success */
+}
+
+/*
+ * checkboard: identify/verify the board we are running
+ *
+ * Remark: we just assume it is correct board here!
+ *
+ */
+int checkboard(void)
+{
+	printf("BOARD: Cogent CSB472\n");
+
+	return 0; /* success */
+}
+
+/*
+ * initram: Determine the size of mounted DRAM
+ *
+ * Size is determined by reading SDRAM configuration registers as
+ * configured by initialization code
+ *
+ */
+long initdram (int board_type)
+{
+	ulong tot_size;
+	ulong bank_size;
+	ulong tmp;
+
+	tot_size = 0;
+
+	mtdcr (memcfga, mem_mb0cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	mtdcr (memcfga, mem_mb1cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	mtdcr (memcfga, mem_mb2cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	mtdcr (memcfga, mem_mb3cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	return tot_size;
+}
+
+/*
+ * last_stage_init: final configurations (such as PHY etc)
+ *
+ */
+int last_stage_init(void)
+{
+	/* initialize the PHY */
+	miiphy_reset(CONFIG_PHY_ADDR);
+	miiphy_write(CONFIG_PHY_ADDR, PHY_BMCR,
+			PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);	/* AUTO neg */
+	miiphy_write(CONFIG_PHY_ADDR, PHY_FCSCR, 0x0d08);	/* LEDs     */
+
+	return 0; /* success */
+}

board/csb472/init.S

@@ -0,0 +1,212 @@
+/******************************************************************************
+ *
+ *	 This source code has been made available to you by IBM on an AS-IS
+ *	 basis.	 Anyone receiving this source is licensed under IBM
+ *	 copyrights to use it in any way he or she deems fit, including
+ *	 copying it, modifying it, compiling it, and redistributing it either
+ *	 with or without modifications.	 No license under IBM patents or
+ *	 patent applications is to be implied by the copyright license.
+ *
+ *	 Any user of this software should understand that IBM cannot provide
+ *	 technical support for this software and will not be responsible for
+ *	 any consequences resulting from the use of this software.
+ *
+ *	 Any person who transfers this source code or any derivative work
+ *	 must include the IBM copyright notice, this paragraph, and the
+ *	 preceding two paragraphs in the transferred software.
+ *
+ *	 COPYRIGHT   I B M   CORPORATION 1995
+ *	 LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+ *
+ *****************************************************************************/
+#include <config.h>
+#include <ppc4xx.h>
+
+#define _LINUX_CONFIG_H 1	/* avoid reading Linux autoconf.h file	*/
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+
+#include <asm/cache.h>
+#include <asm/mmu.h>
+
+#define LI32(reg,val) \
+	addis   reg,0,val@h;\
+	ori     reg,reg,val@l
+
+#define WDCR_EBC(reg,val) \
+	addi    r4,0,reg;\
+	mtdcr   ebccfga,r4;\
+	addis   r4,0,val@h;\
+	ori     r4,r4,val@l;\
+	mtdcr   ebccfgd,r4
+
+#define WDCR_SDRAM(reg,val) \
+	addi    r4,0,reg;\
+	mtdcr   memcfga,r4;\
+	addis   r4,0,val@h;\
+	ori     r4,r4,val@l;\
+	mtdcr   memcfgd,r4
+
+/******************************************************************************
+ * Function:	ext_bus_cntlr_init
+ *
+ * Description:	Configures EBC Controller and a few basic chip selects.
+ *
+ *		CS0 is setup to get the Boot Flash out of the addresss range
+ *		so that we may setup a stack.  CS7 is setup so that we can
+ *		access and reset the hardware watchdog.
+ *
+ *		IMPORTANT: For pass1 this code must run from
+ *		cache since you can not reliably change a peripheral banks
+ *		timing register (pbxap) while running code from that bank.
+ *		For ex., since we are running from ROM on bank 0, we can NOT
+ *		execute the code that modifies bank 0 timings from ROM, so
+ *		we run it from cache.
+ *
+ * Notes:	Does NOT use the stack.
+ *****************************************************************************/
+	.section ".text"
+	.align	2
+	.globl	ext_bus_cntlr_init
+	.type	ext_bus_cntlr_init, @function
+ext_bus_cntlr_init:
+	mflr	r0
+	/********************************************************************
+	 * Prefetch entire ext_bus_cntrl_init function into the icache.
+	 * This is necessary because we are going to change the same CS we
+	 * are executing from.  Otherwise a CPU lockup may occur.
+	 *******************************************************************/
+	bl	..getAddr
+..getAddr:
+	mflr	r3			/* get address of ..getAddr */
+
+	/* Calculate number of cache lines for this function */
+	addi	r4, 0, (((.Lfe0 - ..getAddr) / CFG_CACHELINE_SIZE) + 2)
+	mtctr	r4
+..ebcloop:
+	icbt	r0, r3			/* prefetch cache line for addr in r3*/
+	addi	r3, r3, CFG_CACHELINE_SIZE /* move to next cache line */
+	bdnz	..ebcloop		/* continue for $CTR cache lines */
+
+	/********************************************************************
+	 * Delay to ensure all accesses to ROM are complete before changing
+	 * bank 0 timings. 200usec should be enough.
+	 * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
+	 *******************************************************************/
+	addis	r3, 0, 0x0
+	ori	r3, r3, 0xA000		/* wait 200us from reset */
+	mtctr	r3
+..spinlp:
+	bdnz	..spinlp		/* spin loop */
+
+	/********************************************************************
+	 * SETUP CPC0_CR0
+	 *******************************************************************/
+	LI32(r4, 0x00c01030)
+	mtdcr	cntrl0, r4
+
+	/********************************************************************
+	 * Setup CPC0_CR1: Change PCIINT signal to PerWE
+	 *******************************************************************/
+	mfdcr	r4, cntrl1
+	ori	r4, r4, 0x4000
+	mtdcr	cntrl1, r4
+
+	/********************************************************************
+	 * Setup External Bus Controller (EBC).
+	 *******************************************************************/
+	WDCR_EBC(epcr, 0xd84c0000)
+	/********************************************************************
+	 * Memory Bank 0 (Intel 28F640J3 Flash) initialization
+	 *******************************************************************/
+	/*WDCR_EBC(pb0ap, 0x03055200)*/
+	/*WDCR_EBC(pb0ap, 0x04055200)*/
+	WDCR_EBC(pb0ap, 0x08055200)
+	WDCR_EBC(pb0cr, 0xff87a000)
+	/********************************************************************
+	 * Memory Bank 3 (Xilinx XC95144 CPLD) initialization
+	 *******************************************************************/
+	/*WDCR_EBC(pb3ap, 0x07869200)*/
+	WDCR_EBC(pb3ap, 0x04055200)
+	WDCR_EBC(pb3cr, 0xff01c000)
+	/********************************************************************
+	 * Memory Bank 1,2,4-7 (Unused) initialization
+	 *******************************************************************/
+	WDCR_EBC(pb1ap, 0)
+	WDCR_EBC(pb1cr, 0)
+	WDCR_EBC(pb2ap, 0)
+	WDCR_EBC(pb2cr, 0)
+	WDCR_EBC(pb4ap, 0)
+	WDCR_EBC(pb4cr, 0)
+	WDCR_EBC(pb5ap, 0)
+	WDCR_EBC(pb5cr, 0)
+	WDCR_EBC(pb6ap, 0)
+	WDCR_EBC(pb6cr, 0)
+	WDCR_EBC(pb7ap, 0)
+	WDCR_EBC(pb7cr, 0)
+
+	/* We are all done */
+	mtlr	r0			/* Restore link register */
+	blr				/* Return to calling function */
+.Lfe0:	.size	ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
+/* end ext_bus_cntlr_init() */
+
+/******************************************************************************
+ * Function:	sdram_init
+ *
+ * Description:	Configures SDRAM memory banks.
+ *
+ * Notes:	Does NOT use the stack.
+ *****************************************************************************/
+	.section ".text"
+	.align	2
+	.globl	sdram_init
+	.type	sdram_init, @function
+sdram_init:
+
+	/*
+	 * Disable memory controller to allow
+	 * values to be changed.
+	 */
+	WDCR_SDRAM(mem_mcopt1, 0x00000000)
+
+	/*
+	 * Configure Memory Banks
+	 */
+	WDCR_SDRAM(mem_mb0cf, 0x00062001)
+	WDCR_SDRAM(mem_mb1cf, 0x00000000)
+	WDCR_SDRAM(mem_mb2cf, 0x00000000)
+	WDCR_SDRAM(mem_mb3cf, 0x00000000)
+
+	/*
+	 * Set up SDTR1 (SDRAM Timing Register)
+	 */
+	WDCR_SDRAM(mem_sdtr1, 0x00854009)
+
+	/*
+	 * Set RTR (Refresh Timing Register)
+	 */
+	WDCR_SDRAM(mem_rtr,   0x10000000)
+	/* WDCR_SDRAM(mem_rtr,   0x05f00000) */
+
+	/********************************************************************
+	 * Delay to ensure 200usec have elapsed since reset. Assume worst
+	 * case that the core is running 200Mhz:
+	 *	  200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
+	 *******************************************************************/
+	addis   r3, 0, 0x0000
+	ori     r3, r3, 0xA000		/* Wait >200us from reset */
+	mtctr   r3
+..spinlp2:
+	bdnz    ..spinlp2		/* spin loop */
+
+	/********************************************************************
+	 * Set memory controller options reg, MCOPT1.
+	 *******************************************************************/
+	WDCR_SDRAM(mem_mcopt1,0x80800000)
+
+..sdri_done:
+	blr				/* Return to calling function */
+.Lfe1:	.size	sdram_init,.Lfe1-sdram_init
+/* end sdram_init() */

board/csb472/u-boot.lds

@@ -0,0 +1,151 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    board/csb472/init.o	(.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+
+    lib_ppc/extable.o	(.text)
+    lib_ppc/board.o	(.text)
+    lib_generic/zlib.o	(.text)
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/dave/B2/flash.c

@@ -45,9 +45,6 @@ unsigned long flash_init (void)
 #else
 	unsigned long size_b0;
 	int i;
-	uint pbcr;
-	unsigned long base_b0;
-	int size_val = 0;
 
 	/* Init: no FLASHes known */
 	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {

board/dave/B2/u-boot.lds

@@ -51,7 +51,7 @@ SECTIONS
 	armboot_end_data = .;
 
 	. = ALIGN(4);
+	__bss_start = .;
 	.bss : { *(.bss) }
-
-	armboot_end = .;
+	_end = .;
 }

board/dave/PPChameleonEVB/PPChameleonEVB.c

@@ -31,26 +31,9 @@
 
 /* ------------------------------------------------------------------------- */
 
-#if 0
-#define FPGA_DEBUG
-#endif
-
-/* fpga configuration data - gzip compressed and generated by bin2c */
-const unsigned char fpgadata[] =
-{
-#include "fpgadata.c"
-};
-
-/*
- * include common fpga code (for esd boards)
- */
-#include "../common/fpga.c"
-
-
 /* Prototypes */
 int gunzip(void *, int, unsigned char *, int *);
 
-
 int board_early_init_f (void)
 {
 	out32(GPIO0_OR, CFG_NAND0_CE);                 /* set initial outputs     */
@@ -60,13 +43,13 @@ int board_early_init_f (void)
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive
 	 * IRQ 16    405GP internally generated; active low; level sensitive
 	 * IRQ 17-24 RESERVED
-	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
-	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
-	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
-	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
-	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
-	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
-	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 * IRQ 25 (EXT IRQ 0)
+	 * IRQ 26 (EXT IRQ 1)
+	 * IRQ 27 (EXT IRQ 2)
+	 * IRQ 28 (EXT IRQ 3)
+	 * IRQ 29 (EXT IRQ 4)
+	 * IRQ 30 (EXT IRQ 5)
+	 * IRQ 31 (EXT IRQ 6)
 	 */
 	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
 	mtdcr(uicer, 0x00000000);       /* disable all ints */
@@ -84,11 +67,9 @@ int board_early_init_f (void)
 #else
 	mtebc (epcr, 0x28400000); /* ebc in high-z */
 #endif
-
 	return 0;
 }
 
-
 /* ------------------------------------------------------------------------- */
 
 int misc_init_f (void)
@@ -96,11 +77,15 @@ int misc_init_f (void)
 	return 0;  /* dummy implementation */
 }
 
+extern flash_info_t flash_info[];	/* info for FLASH chips */
 
 int misc_init_r (void)
 {
-#if 0 /* test-only */
 	DECLARE_GLOBAL_DATA_PTR;
+
+	/* adjust flash start and size as well as the offset */
+	gd->bd->bi_flashstart = 0 - flash_info[0].size;
+	gd->bd->bi_flashoffset= flash_info[0].size - CFG_MONITOR_LEN;
 #if 0
 	volatile unsigned short *fpga_mode =
 		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL);
@@ -177,7 +162,6 @@ int misc_init_r (void)
 	udelay(1000); /* wait 1ms */
 	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
 	udelay(1000); /* wait 1ms */
-
 #endif
 
 #if 0
@@ -192,12 +176,9 @@ int misc_init_r (void)
 	*duart0_mcr = 0x08;
 	*duart1_mcr = 0x08;
 #endif
-#endif
-
 	return (0);
 }
 
-
 /*
  * Check Board Identity:
  */
@@ -266,8 +247,13 @@ nand_init(void)
 {
 	ulong totlen = 0;
 
-#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) || \
+/*
+	The HI model is equipped with a large block NAND chip not supported yet
+	by U-Boot
     (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
+*/
+
+#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
 	debug ("Probing at 0x%.8x\n", CFG_NAND0_BASE);
 	totlen += nand_probe (CFG_NAND0_BASE);
 #endif	/* CONFIG_PPCHAMELEON_MODULE_ME, CONFIG_PPCHAMELEON_MODULE_HI */
@@ -278,3 +264,39 @@ nand_init(void)
 	printf ("%4lu MB\n", totlen >>20);
 }
 #endif
+
+#ifdef CONFIG_CFB_CONSOLE
+# ifdef CONFIG_CONSOLE_EXTRA_INFO
+# include <video_fb.h>
+extern GraphicDevice smi;
+
+void video_get_info_str (int line_number, char *info)
+{
+	uint pvr = get_pvr ();
+
+	/* init video info strings for graphic console */
+	switch (line_number) {
+	case 1:
+		switch (pvr) {
+		case PVR_405EP_RB:
+			sprintf (info, " IBM PowerPC 405EP Rev. B");
+			break;
+		default:
+			sprintf (info, " IBM PowerPC 405EP Rev. <unknown>");
+			break;
+		}
+		return;
+	case 2:
+		sprintf (info, " DAVE Srl PPChameleonEVB - www.dave-tech.it");
+		return;
+	case 3:
+		sprintf (info, " %s", smi.modeIdent);
+		return;
+	}
+
+	/* no more info lines */
+	*info = 0;
+	return;
+}
+# endif	/* CONFIG_CONSOLE_EXTRA_INFO */
+#endif	/* CONFIG_CFB_CONSOLE */

board/dave/PPChameleonEVB/flash.c

@@ -44,12 +44,15 @@ unsigned long flash_init (void)
 #ifdef __DEBUG_START_FROM_SRAM__
 	return CFG_DUMMY_FLASH_SIZE;
 #else
-	unsigned long size_b0;
+	unsigned long size;
 	int i;
 	uint pbcr;
-	unsigned long base_b0;
+	unsigned long base;
 	int size_val = 0;
 
+	debug("[%s, %d] Entering ...\n", __FUNCTION__, __LINE__);
+	debug("[%s, %d] flash_info = 0x%08X ...\n", __FUNCTION__, __LINE__, flash_info);
+
 	/* Init: no FLASHes known */
 	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
 		flash_info[i].flash_id = FLASH_UNKNOWN;
@@ -57,22 +60,26 @@ unsigned long flash_init (void)
 
 	/* Static FLASH Bank configuration here - FIXME XXX */
 
-	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+	debug("[%s, %d] Calling flash_get_size ...\n", __FUNCTION__, __LINE__);
+	size = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
 
 	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
 		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size_b0, size_b0<<20);
+			size, size<<20);
 	}
 
+	debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
+
 	/* Setup offsets */
-	flash_get_offsets (-size_b0, &flash_info[0]);
+	flash_get_offsets (-size, &flash_info[0]);
+	debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
 
 	/* Re-do sizing to get full correct info */
 	mtdcr(ebccfga, pb0cr);
 	pbcr = mfdcr(ebccfgd);
 	mtdcr(ebccfga, pb0cr);
-	base_b0 = -size_b0;
-	switch (size_b0) {
+	base = -size;
+	switch (size) {
 	case 1 << 20:
 		size_val = 0;
 		break;
@@ -89,8 +96,9 @@ unsigned long flash_init (void)
 		size_val = 4;
 		break;
 	}
-	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+	pbcr = (pbcr & 0x0001ffff) | base | (size_val << 17);
 	mtdcr(ebccfgd, pbcr);
+	debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
 
 	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
@@ -98,8 +106,9 @@ unsigned long flash_init (void)
 			    0xffffffff,
 			    &flash_info[0]);
 
-	flash_info[0].size = size_b0;
+	debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
+	flash_info[0].size  = size;
 
-	return (size_b0);
+	return (size);
 #endif
 }

board/dave/PPChameleonEVB/u-boot.lds

@@ -73,9 +73,6 @@ SECTIONS
     lib_ppc/extable.o	(.text)
     lib_generic/zlib.o		(.text)
 
-/*    . = env_offset;*/
-/*    common/environment.o(.text)*/
-
     *(.text)
     *(.fixup)
     *(.got1)
@@ -142,6 +139,13 @@ SECTIONS
    *(.bss)
    *(COMMON)
   }
+
+  . = 0xFFFF8000;
+  .ppcenv :
+  {
+    common/environment.o(.ppcenv);
+  }
+
   _end = . ;
   PROVIDE (end = .);
 }

board/dave/common/flash.c

@@ -220,6 +220,8 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 	ulong base = (ulong)addr;
 	volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *)addr;
 
+	debug("[%s, %d] Entering ...\n", __FUNCTION__, __LINE__);
+
 	/* Write auto select command: read Manufacturer ID */
 	addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE)0x00AA00AA;
 	addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE)0x00550055;
@@ -669,8 +671,7 @@ static int write_word (flash_info_t *info, ulong dest, ulong data)
 	int i;
 
 	/* Check if Flash is (sufficiently) erased */
-	if ((*((volatile CFG_FLASH_WORD_SIZE *)dest) &
-	     (CFG_FLASH_WORD_SIZE)data) != (CFG_FLASH_WORD_SIZE)data) {
+	if ((*((volatile ulong *)dest) & data) != data) {
 		return (2);
 	}
 	/* Disable interrupts which might cause a timeout here */

board/dbau1x00/dbau1x00.c

@@ -104,17 +104,17 @@ int checkboard (void)
 		      CFG_PCMCIA_ATTR_BASE, /* Hi */
 		      0x3D000017,           /* Lo0 */
 		      0x3D200017);          /* Lo1 */
-#endif
+#endif	/* 0 */
 	write_one_tlb(22,                   /* index */
 		      0x01ffe000,           /* Pagemask, 16 MB pages */
 		      CFG_PCMCIA_MEM_ADDR,  /* Hi */
 		      0x3E000017,           /* Lo0 */
 		      0x3E200017);          /* Lo1 */
+#endif	/* CONFIG_IDE_PCMCIA */
 
 	/* Release reset of ethernet PHY chips */
 	/* Always do this, because linux does not know about it */
 	*phy = 3;
 
 	return 0;
-#endif
 }

board/eXalion/Makefile

@@ -29,7 +29,7 @@ OBJS	= $(BOARD).o
 SOBJS	=
 
 $(LIB):	.depend $(OBJS) $(SOBJS)
-	$(AR) crv $@ $^
+	$(AR) crv $@ $(OBJS) $(SOBJS)
 
 #########################################################################
 

board/eltec/elppc/misc.c

@@ -250,10 +250,6 @@ int misc_init_r (void)
 		 eerev.etheraddr[4], eerev.etheraddr[5]);
 	setenv ("ethaddr", buf);
 
-	/* set serial console as default */
-	if ((ptr = getenv ("console")) == NULL)
-		setenv ("console", "serial");
-
 	/* print actual board identification */
 	printf ("Ident: %s  Ser %s  Rev %c%c\n",
 		eerev.board, (char *) &eerev.serial,

board/emk/common/flash.c

@@ -40,9 +40,11 @@ flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
   #define FLASH_CYCLE2	0x02aa
   #define FLASH_ID1		0
   #define FLASH_ID2		1
+  #define FLASH_ID3		0x0e
+  #define FLASH_ID4		0x0F
 #endif
 
-#if defined (CONFIG_TOP5200)
+#if defined (CONFIG_TOP5200) && !defined (CONFIG_LITE5200)
   typedef unsigned char FLASH_PORT_WIDTH;
   typedef volatile unsigned char FLASH_PORT_WIDTHV;
   #define	FLASH_ID_MASK	0xFF
@@ -54,6 +56,24 @@ flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
   #define FLASH_CYCLE2	0x0555
   #define FLASH_ID1		0
   #define FLASH_ID2		2
+  #define FLASH_ID3		0x1c
+  #define FLASH_ID4		0x1E
+#endif
+
+#if defined (CONFIG_TOP5200) && defined (CONFIG_LITE5200)
+  typedef unsigned char FLASH_PORT_WIDTH;
+  typedef volatile unsigned char FLASH_PORT_WIDTHV;
+  #define	FLASH_ID_MASK	0xFF
+
+  #define FPW	FLASH_PORT_WIDTH
+  #define FPWV	FLASH_PORT_WIDTHV
+
+  #define FLASH_CYCLE1	0x0555
+  #define FLASH_CYCLE2	0x02aa
+  #define FLASH_ID1		0
+  #define FLASH_ID2		1
+  #define FLASH_ID3		0x0E
+  #define FLASH_ID4		0x0F
 #endif
 
 /*-----------------------------------------------------------------------
@@ -183,6 +203,15 @@ void flash_print_info (flash_info_t *info)
 	case FLASH_AM160B:
 		fmt = "29LV160%s (16 Mbit, %s)\n";
 		break;
+	case FLASH_AMLV640U:
+		fmt = "29LV640M (64 Mbit)\n";
+		break;
+	case FLASH_AMDLV065D:
+		fmt = "29LV065D (64 Mbit)\n";
+		break;
+	case FLASH_AMLV256U:
+		fmt = "29LV256M (256 Mbit)\n";
+		break;
 	default:
 		fmt = "Unknown Chip Type\n";
 		break;
@@ -239,7 +268,6 @@ void flash_print_info (flash_info_t *info)
 ulong flash_get_size (FPWV *addr, flash_info_t *info)
 {
 	int		i;
-	ulong	offset;
 
 	/* Write auto select command: read Manufacturer ID */
 	/* Write auto select command sequence and test FLASH answer */
@@ -278,27 +306,64 @@ ulong flash_get_size (FPWV *addr, flash_info_t *info)
 		info->flash_id += FLASH_AM160B;
 		info->sector_count = 35;
 		info->size = 0x00200000;
-#ifdef CFG_LOWBOOT
-		offset = 0;
-#else
-		offset = 0x00e00000;
-#endif
-		info->start[0] = (ulong)addr + offset;
-		info->start[1] = (ulong)addr + offset + 0x4000;
-		info->start[2] = (ulong)addr + offset + 0x6000;
-		info->start[3] = (ulong)addr + offset + 0x8000;
+		info->start[0] = (ulong)addr;
+		info->start[1] = (ulong)addr + 0x4000;
+		info->start[2] = (ulong)addr + 0x6000;
+		info->start[3] = (ulong)addr + 0x8000;
 		for (i = 4; i < info->sector_count; i++)
 		{
-			info->start[i] = (ulong)addr + offset + 0x10000 * (i-3);
+			info->start[i] = (ulong)addr + 0x10000 * (i-3);
 		}
 		break;
 
+	case (FPW)AMD_ID_LV065D:
+		info->flash_id += FLASH_AMDLV065D;
+		info->sector_count = 128;
+		info->size = 0x00800000;
+		for (i = 0; i < info->sector_count; i++)
+		{
+			info->start[i] = (ulong)addr + 0x10000 * i;
+		}
+		break;
+
+	case (FPW)AMD_ID_MIRROR:
+		/* MIRROR BIT FLASH, read more ID bytes */
+		if ((FPW)addr[FLASH_ID3] == (FPW)AMD_ID_LV640U_2 &&
+			(FPW)addr[FLASH_ID4] == (FPW)AMD_ID_LV640U_3)
+		{
+			info->flash_id += FLASH_AMLV640U;
+			info->sector_count = 128;
+			info->size = 0x00800000;
+			for (i = 0; i < info->sector_count; i++)
+			{
+				info->start[i] = (ulong)addr + 0x10000 * i;
+			}
+			break;
+		}
+		if ((FPW)addr[FLASH_ID3] == (FPW)AMD_ID_LV256U_2 &&
+			(FPW)addr[FLASH_ID4] == (FPW)AMD_ID_LV256U_3)
+		{
+			/* attention: only the first 16 MB will be used in u-boot */
+			info->flash_id += FLASH_AMLV256U;
+			info->sector_count = 256;
+			info->size = 0x01000000;
+			for (i = 0; i < info->sector_count; i++)
+			{
+				info->start[i] = (ulong)addr + 0x10000 * i;
+			}
+			break;
+		}
+
+		/* fall thru to here ! */
 	default:
-		printf ("unknown AMD device=%x ", (FPW)addr[FLASH_ID2]);
+		printf ("unknown AMD device=%x %x %x",
+			(FPW)addr[FLASH_ID2],
+			(FPW)addr[FLASH_ID3],
+			(FPW)addr[FLASH_ID4]);
 		info->flash_id = FLASH_UNKNOWN;
 		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* => no or unknown flash */
+		info->size = 0x800000;
+		break;
 	}
 
 	/* Put FLASH back in read mode */
@@ -329,6 +394,7 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 
 	switch (info->flash_id & FLASH_TYPEMASK) {
 	case FLASH_AM160B:
+	case FLASH_AMLV640U:
 		break;
 	case FLASH_UNKNOWN:
 	default:

board/emk/top5200/top5200.c

@@ -57,7 +57,7 @@ long int initdram (int board_type)
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN;
 	/* precharge all banks */
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN | SOFT_PRE;
-#if CFG_DRAM_DDR
+#ifdef CFG_DRAM_DDR
 	/* set extended mode register */
 	*(vu_short *)MPC5XXX_SDRAM_MODE = CFG_DRAM_EMODE;
 #endif
@@ -113,11 +113,15 @@ int checkboard (void)
 #if defined (CONFIG_EVAL5200)
 	puts ("Board: EMK TOP5200 on EVAL5200\n");
 #else
+#if defined (CONFIG_LITE5200)
+	puts ("Board: LITE5200\n");
+#else
 #if defined (CONFIG_MINI5200)
 	puts ("Board: EMK TOP5200 on MINI5200\n");
 #else
 	puts ("Board: EMK TOP5200\n");
 #endif
+#endif
 #endif
 	return 0;
 }
@@ -155,10 +159,11 @@ void flash_afterinit(uint bank, ulong start, ulong size)
  *****************************************************************************/
 int misc_init_r (void)
 {
+#if !defined (CONFIG_LITE5200)
 	/* read 'factory' part of EEPROM */
 	extern void read_factory_r (void);
 	read_factory_r ();
-
+#endif
 	return (0);
 }
 
@@ -175,3 +180,31 @@ void pci_init_board(void)
 	pci_mpc5xxx_init(&hose);
 }
 #endif
+
+/*****************************************************************************
+ * provide the IDE Reset Function
+ *****************************************************************************/
+#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+
+#define GPIO_PSC1_4	0x01000000UL
+
+void init_ide_reset (void)
+{
+	debug ("init_ide_reset\n");
+
+    	/* Configure PSC1_4 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
+}
+
+void ide_set_reset (int idereset)
+{
+	debug ("ide_reset(%d)\n", idereset);
+
+	if (idereset) {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
+	} else {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA |=  GPIO_PSC1_4;
+	}
+}
+#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */

board/etin/debris/debris.c

@@ -24,6 +24,7 @@
 #include <common.h>
 #include <mpc824x.h>
 #include <pci.h>
+#include <i2c.h>
 
 int checkboard (void)
 {
@@ -52,28 +53,70 @@ int checkflash (void)
 
 long int initdram (int board_type)
 {
-	long size;
-#if 0
-	long new_bank0_end;
-	long mear1;
-	long emear1;
-#endif
+	int m, row, col, bank, i;
+	unsigned long start, end;
+	uint32_t mccr1;
+	uint32_t mear1 = 0, emear1 = 0, msar1 = 0, emsar1 = 0;
+	uint32_t mear2 = 0, emear2 = 0, msar2 = 0, emsar2 = 0;
+	uint8_t mber = 0;
 
-	size = get_ram_size(CFG_SDRAM_BASE, CFG_MAX_RAM_SIZE);
+	i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
 
-#if 0
-	new_bank0_end = size - 1;
-	mear1 = mpc824x_mpc107_getreg(MEAR1);
-	emear1 = mpc824x_mpc107_getreg(EMEAR1);
-	mear1 = (mear1  & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
-	emear1 = (emear1 & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
-	mpc824x_mpc107_setreg(MEAR1, mear1);
-	mpc824x_mpc107_setreg(EMEAR1, emear1);
-#endif
+	if (i2c_reg_read (0x50, 2) != 0x04) return 0;	/* Memory type */
+	m = i2c_reg_read (0x50, 5);	/* # of physical banks */
+	row = i2c_reg_read (0x50, 3);	/* # of rows */
+	col = i2c_reg_read (0x50, 4);	/* # of columns */
+	bank = i2c_reg_read (0x50, 17);	/* # of logical banks */
 
-	return (size);
+	CONFIG_READ_WORD(MCCR1, mccr1);
+	mccr1 &= 0xffff0000;
+
+	start = CFG_SDRAM_BASE;
+	end = start + (1 << (col + row + 3) ) * bank - 1;
+
+	for (i = 0; i < m; i++) {
+		mccr1 |= ((row == 13)? 2 : (bank == 4)? 0 : 3) << i * 2;
+		if (i < 4) {
+			msar1  |= ((start >> 20) & 0xff) << i * 8;
+			emsar1 |= ((start >> 28) & 0xff) << i * 8;
+			mear1  |= ((end >> 20) & 0xff) << i * 8;
+			emear1 |= ((end >> 28) & 0xff) << i * 8;
+		} else {
+			msar2  |= ((start >> 20) & 0xff) << (i-4) * 8;
+			emsar2 |= ((start >> 28) & 0xff) << (i-4) * 8;
+			mear2  |= ((end >> 20) & 0xff) << (i-4) * 8;
+			emear2 |= ((end >> 28) & 0xff) << (i-4) * 8;
+		}
+		mber |= 1 << i;
+		start += (1 << (col + row + 3) ) * bank;
+		end += (1 << (col + row + 3) ) * bank;
+	}
+	for (; i < 8; i++) {
+		if (i < 4) {
+			msar1  |= 0xff << i * 8;
+			emsar1 |= 0x30 << i * 8;
+			mear1  |= 0xff << i * 8;
+			emear1 |= 0x30 << i * 8;
+		} else {
+			msar2  |= 0xff << (i-4) * 8;
+			emsar2 |= 0x30 << (i-4) * 8;
+			mear2  |= 0xff << (i-4) * 8;
+			emear2 |= 0x30 << (i-4) * 8;
+		}
+	}
+
+	CONFIG_WRITE_WORD(MCCR1, mccr1);
+	CONFIG_WRITE_WORD(MSAR1, msar1);
+	CONFIG_WRITE_WORD(EMSAR1, emsar1);
+	CONFIG_WRITE_WORD(MEAR1, mear1);
+	CONFIG_WRITE_WORD(EMEAR1, emear1);
+	CONFIG_WRITE_WORD(MSAR2, msar2);
+	CONFIG_WRITE_WORD(EMSAR2, emsar2);
+	CONFIG_WRITE_WORD(MEAR2, mear2);
+	CONFIG_WRITE_WORD(EMEAR2, emear2);
+	CONFIG_WRITE_BYTE(MBER, mber);
+
+	return (1 << (col + row + 3) ) * bank * m;
 }
 
 /*

board/evb4510/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= evb4510.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/evb4510/config.mk

@@ -0,0 +1,27 @@
+#
+# Copyright (c) 2004	Cucy Systems (http://www.cucy.com)
+# Curt Brune <curt@cucy.com>
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x007d0000

board/evb4510/evb4510.c

@@ -0,0 +1,65 @@
+/*
+ * Copyright (c) 2004	Cucy Systems (http://www.cucy.com)
+ * Curt Brune <curt@cucy.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/hardware.h>
+#include <command.h>
+
+#ifdef CONFIG_EVB4510
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	icache_enable();
+
+	/* address for the kernel command line */
+	gd->bd->bi_boot_params = 0x800;
+
+	/* enable board LEDs for output */
+	PUT_REG( REG_IOPDATA, 0x0);
+	PUT_REG( REG_IOPMODE, 0xFFFF);
+	PUT_REG( REG_IOPDATA, 0xFF);
+
+	return 0;
+}
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size  = PHYS_SDRAM_1_SIZE;
+#if CONFIG_NR_DRAM_BANKS == 2
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size  = PHYS_SDRAM_2_SIZE;
+#endif
+	return 0;
+}
+
+#endif

board/evb4510/flash.c

@@ -0,0 +1,540 @@
+/*
+ *
+ * Copyright (c) 2004	Cucy Systems (http://www.cucy.com)
+ * Curt Brune <curt@cucy.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/hardware.h>
+#include <flash.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+typedef enum {
+	FLASH_DEV_U9_512KB = 0,
+	FLASH_DEV_U7_2MB = 1
+} FLASH_DEV;
+
+#define FLASH_DQ7		(0x80)
+#define FLASH_DQ5		(0x20)
+
+#define PROG_ADDR		(0xAAA)
+#define SETUP_ADDR		(0xAAA)
+#define ID_ADDR			(0xAAA)
+#define UNLOCK_ADDR1		(0xAAA)
+#define UNLOCK_ADDR2		(0x555)
+
+#define UNLOCK_CMD1		(0xAA)
+#define UNLOCK_CMD2		(0x55)
+#define ERASE_SUSPEND_CMD	(0xB0)
+#define ERASE_RESUME_CMD	(0x30)
+#define RESET_CMD		(0xF0)
+#define ID_CMD			(0x90)
+#define SELECT_CMD		(0x90)
+#define CHIPERASE_CMD		(0x10)
+#define BYPASS_CMD		(0x20)
+#define SECERASE_CMD		(0x30)
+#define PROG_CMD		(0xa0)
+#define SETUP_CMD		(0x80)
+
+#if 0
+#define WRITE_UNLOCK(addr) { \
+	PUT__U8( addr + UNLOCK_ADDR1, UNLOCK_CMD1); \
+	PUT__U8( addr + UNLOCK_ADDR2, UNLOCK_CMD2); \
+}
+
+/* auto select command */
+#define CMD_ID(addr) WRITE_UNLOCK(addr); { \
+	PUT__U8( addr + ID_ADDR, ID_CMD); \
+}
+
+#define CMD_RESET(addr) WRITE_UNLOCK(addr); { \
+	PUT__U8( addr + ID_ADDR, RESET_CMD); \
+}
+
+#define CMD_ERASE_SEC(base, addr) WRITE_UNLOCK(base); \
+	PUT__U8( base + SETUP_ADDR, SETUP_CMD); \
+	WRITE_UNLOCK(base); \
+	PUT__U8( addr, SECERASE_CMD);
+
+#define CMD_ERASE_CHIP(base) WRITE_UNLOCK(base); \
+	PUT__U8( base + SETUP_ADDR, SETUP_CMD); \
+	WRITE_UNLOCK(base); \
+	PUT__U8( base + SETUP_ADDR, CHIPERASE_CMD);
+
+/* prepare for bypass programming */
+#define CMD_UNLOCK_BYPASS(addr) WRITE_UNLOCK(addr); { \
+	PUT__U8( addr + ID_ADDR, 0x20); \
+}
+
+/* terminate bypass programming */
+#define CMD_BYPASS_RESET(addr) { \
+	PUT__U8(addr, 0x90); \
+	PUT__U8(addr, 0x00); \
+}
+#endif
+
+inline static void FLASH_CMD_UNLOCK (FLASH_DEV dev, u32 base)
+{
+	switch (dev) {
+	case FLASH_DEV_U7_2MB:
+		PUT__U8 (base + 0xAAA, 0xAA);
+		PUT__U8 (base + 0x555, 0x55);
+		break;
+	case FLASH_DEV_U9_512KB:
+		PUT__U8 (base + 0x555, 0xAA);
+		PUT__U8 (base + 0x2AA, 0x55);
+		break;
+	}
+}
+
+inline static void FLASH_CMD_SELECT (FLASH_DEV dev, u32 base)
+{
+	switch (dev) {
+	case FLASH_DEV_U7_2MB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0xAAA, SELECT_CMD);
+		break;
+	case FLASH_DEV_U9_512KB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0x555, SELECT_CMD);
+		break;
+	}
+}
+
+inline static void FLASH_CMD_RESET (FLASH_DEV dev, u32 base)
+{
+	switch (dev) {
+	case FLASH_DEV_U7_2MB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0xAAA, RESET_CMD);
+		break;
+	case FLASH_DEV_U9_512KB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0x555, RESET_CMD);
+		break;
+	}
+}
+
+inline static void FLASH_CMD_ERASE_SEC (FLASH_DEV dev, u32 base, u32 addr)
+{
+	switch (dev) {
+	case FLASH_DEV_U7_2MB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0xAAA, SETUP_CMD);
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (addr, SECERASE_CMD);
+		break;
+	case FLASH_DEV_U9_512KB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0x555, SETUP_CMD);
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (addr, SECERASE_CMD);
+		break;
+	}
+}
+
+inline static void FLASH_CMD_ERASE_CHIP (FLASH_DEV dev, u32 base)
+{
+	switch (dev) {
+	case FLASH_DEV_U7_2MB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0xAAA, SETUP_CMD);
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base, CHIPERASE_CMD);
+		break;
+	case FLASH_DEV_U9_512KB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0x555, SETUP_CMD);
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base, CHIPERASE_CMD);
+		break;
+	}
+}
+
+inline static void FLASH_CMD_UNLOCK_BYPASS (FLASH_DEV dev, u32 base)
+{
+	switch (dev) {
+	case FLASH_DEV_U7_2MB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0xAAA, BYPASS_CMD);
+		break;
+	case FLASH_DEV_U9_512KB:
+		FLASH_CMD_UNLOCK (dev, base);
+		PUT__U8 (base + 0x555, BYPASS_CMD);
+		break;
+	}
+}
+
+inline static void FLASH_CMD_BYPASS_RESET (FLASH_DEV dev, u32 base)
+{
+	PUT__U8 (base, SELECT_CMD);
+	PUT__U8 (base, 0x0);
+}
+
+/* poll for flash command completion */
+static u16 _flash_poll (FLASH_DEV dev, u32 addr, u16 data, ulong timeOut)
+{
+	u32 done = 0;
+	ulong t0;
+
+	u16 error = 0;
+	volatile u16 flashData;
+
+	data = data & 0xFF;
+	t0 = get_timer (0);
+	while (get_timer (t0) < timeOut) {
+		/*	for( i = 0; i < POLL_LOOPS; i++) { */
+		/*  Read the Data */
+		flashData = GET__U8 (addr);
+
+		/*  FLASH_DQ7 = Data? */
+		if ((flashData & FLASH_DQ7) == (data & FLASH_DQ7)) {
+			done = 1;
+			break;
+		}
+
+		/*  Check Timeout (FLASH_DQ5==1) */
+		if (flashData & FLASH_DQ5) {
+			/*  Read the Data */
+			flashData = GET__U8 (addr);
+
+			/*  FLASH_DQ7 = Data? */
+			if (!((flashData & FLASH_DQ7) == (data & FLASH_DQ7))) {
+				printf ("_flash_poll(): FLASH_DQ7 & flashData not equal to write value\n");
+				error = ERR_PROG_ERROR;
+			}
+			FLASH_CMD_RESET (dev, addr);
+			done = 1;
+			break;
+		}
+		/*  spin delay */
+		udelay (10);
+	}
+
+
+	/*  error update */
+	if (!done) {
+		printf ("_flash_poll(): Timeout\n");
+		error = ERR_TIMOUT;
+	}
+
+	/*  Check the data */
+	if (!error) {
+		/*  Read the Data */
+		flashData = GET__U8 (addr);
+		if (flashData != data) {
+			error = ERR_PROG_ERROR;
+			printf ("_flash_poll(): flashData(0x%04x) not equal to data(0x%04x)\n",
+				flashData, data);
+		}
+	}
+
+	return error;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static int _flash_check_protection (flash_info_t * info, int s_first, int s_last)
+{
+	int sect, prot = 0;
+
+	for (sect = s_first; sect <= s_last; sect++)
+		if (info->protect[sect]) {
+			printf ("  Flash sector %d protected.\n", sect);
+			prot++;
+		}
+	return prot;
+}
+
+static int _detectFlash (FLASH_DEV dev, u32 base, u8 venId, u8 devId)
+{
+
+	u32 baseAddr = base | CACHE_DISABLE_MASK;
+	u8 vendorId, deviceId;
+
+	/*	printf(__FUNCTION__"(): detecting flash @ 0x%08x\n", base); */
+
+	/* Send auto select command and read manufacturer info */
+	FLASH_CMD_SELECT (dev, baseAddr);
+	vendorId = GET__U8 (baseAddr);
+	FLASH_CMD_RESET (dev, baseAddr);
+
+	/* Send auto select command and read device info */
+	FLASH_CMD_SELECT (dev, baseAddr);
+
+	if (dev == FLASH_DEV_U7_2MB) {
+		deviceId = GET__U8 (baseAddr + 2);
+	} else if (dev == FLASH_DEV_U9_512KB) {
+		deviceId = GET__U8 (baseAddr + 1);
+	} else {
+		return 0;
+	}
+
+	FLASH_CMD_RESET (dev, baseAddr);
+
+	/* printf (__FUNCTION__"(): found vendorId 0x%04x, deviceId 0x%04x\n",
+		vendorId, deviceId);
+	 */
+
+	return (vendorId == venId) && (deviceId == devId);
+
+}
+
+/******************************************************************************
+ *
+ * Public u-boot interface functions below
+ *
+ *****************************************************************************/
+
+/***************************************************************************
+ *
+ * Flash initialization
+ *
+ * This board has two banks of flash, but the base addresses depend on
+ * how the board is jumpered.
+ *
+ * The two flash types are:
+ *
+ *   AMD Am29LV160DB (2MB) sectors layout 16KB, 2x8KB, 32KB, 31x64KB
+ *
+ *   AMD Am29LV040B  (512KB)  sectors: 8x64KB
+ *****************************************************************************/
+
+unsigned long flash_init (void)
+{
+	flash_info_t *info;
+	u16 i;
+	u32 flashtest;
+	s16 amd160 = -1;
+	u32 amd160base = 0;
+
+#if CFG_MAX_FLASH_BANKS == 2
+	s16 amd040 = -1;
+	u32 amd040base = 0;
+#endif
+
+	/* configure PHYS_FLASH_1 */
+	if (_detectFlash (FLASH_DEV_U7_2MB, PHYS_FLASH_1, 0x1, 0x49)) {
+		amd160 = 0;
+		amd160base = PHYS_FLASH_1;
+#if CFG_MAX_FLASH_BANKS == 1
+	}
+#else
+		if (_detectFlash
+		    (FLASH_DEV_U9_512KB, PHYS_FLASH_2, 0x1, 0x4F)) {
+			amd040 = 1;
+			amd040base = PHYS_FLASH_2;
+		} else {
+			printf (__FUNCTION__
+				"(): Unable to detect PHYS_FLASH_2: 0x%08x\n",
+				PHYS_FLASH_2);
+		}
+	} else if (_detectFlash (FLASH_DEV_U9_512KB, PHYS_FLASH_1, 0x1, 0x4F)) {
+		amd040 = 0;
+		amd040base = PHYS_FLASH_1;
+		if (_detectFlash (FLASH_DEV_U7_2MB, PHYS_FLASH_2, 0x1, 0x49)) {
+			amd160 = 1;
+			amd160base = PHYS_FLASH_2;
+		} else {
+			printf (__FUNCTION__
+				"(): Unable to detect PHYS_FLASH_2: 0x%08x\n",
+				PHYS_FLASH_2);
+		}
+	}
+#endif
+	else {
+		printf (__FUNCTION__
+			"(): Unable to detect PHYS_FLASH_1: 0x%08x\n",
+			PHYS_FLASH_1);
+	}
+
+	/* Configure AMD Am29LV160DB (2MB) */
+	info = &flash_info[amd160];
+	info->flash_id = FLASH_DEV_U7_2MB;
+	info->sector_count = 35;
+	info->size = 2 * 1024 * 1024;	/* 2MB */
+	/* 1*16K Boot Block
+	   2*8K Parameter Block
+	   1*32K Small Main Block */
+	info->start[0] = amd160base;
+	info->start[1] = amd160base + 0x4000;
+	info->start[2] = amd160base + 0x6000;
+	info->start[3] = amd160base + 0x8000;
+	for (i = 1; i < info->sector_count; i++)
+		info->start[3 + i] = amd160base + i * (64 * 1024);
+
+	for (i = 0; i < info->sector_count; i++) {
+		/* Write auto select command sequence and query sector protection */
+		FLASH_CMD_SELECT (info->flash_id,
+				  info->start[i] | CACHE_DISABLE_MASK);
+		flashtest =
+			GET__U8 (((info->start[i] + 4) | CACHE_DISABLE_MASK));
+		FLASH_CMD_RESET (info->flash_id,
+				 amd160base | CACHE_DISABLE_MASK);
+		info->protect[i] = (flashtest & 0x0001);
+	}
+
+	/*
+	 * protect monitor and environment sectors in 2MB flash
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+		       amd160base, amd160base + monitor_flash_len - 1, info);
+
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR, CFG_ENV_ADDR + CFG_ENV_SIZE - 1, info);
+
+#if CFG_MAX_FLASH_BANKS == 2
+	/* Configure AMD Am29LV040B (512KB) */
+	info = &flash_info[amd040];
+	info->flash_id = FLASH_DEV_U9_512KB;
+	info->sector_count = 8;
+	info->size = 512 * 1024;	/* 512KB, 8 x 64KB */
+	for (i = 0; i < info->sector_count; i++) {
+		info->start[i] = amd040base + i * (64 * 1024);
+		/* Write auto select command sequence and query sector protection */
+		FLASH_CMD_SELECT (info->flash_id,
+				  info->start[i] | CACHE_DISABLE_MASK);
+		flashtest =
+			GET__U8 (((info->start[i] + 2) | CACHE_DISABLE_MASK));
+		FLASH_CMD_RESET (info->flash_id,
+				 amd040base | CACHE_DISABLE_MASK);
+		info->protect[i] = (flashtest & 0x0001);
+	}
+#endif
+
+	return flash_info[0].size
+#if CFG_MAX_FLASH_BANKS == 2
+		+ flash_info[1].size
+#endif
+		;
+}
+
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_DEV_U7_2MB) {
+		printf ("AMD Am29LV160DB (2MB) 16KB,2x8KB,32KB,31x64KB\n");
+	} else if (info->flash_id == FLASH_DEV_U9_512KB) {
+		printf ("AMD Am29LV040B	 (512KB) 8x64KB\n");
+	} else {
+		printf ("Unknown flash_id ...\n");
+		return;
+	}
+
+	printf ("  Size: %ld KB in %d Sectors\n",
+		info->size >> 10, info->sector_count);
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; i++) {
+		if ((i % 4) == 0)
+			printf ("\n   ");
+		printf (" S%02d @ 0x%08lX%s", i,
+			info->start[i], info->protect[i] ? " !" : "  ");
+	}
+	printf ("\n");
+}
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	u16 i, error = 0;
+
+	printf ("\n");
+
+	/* check flash protection bits */
+	if (_flash_check_protection (info, s_first, s_last)) {
+		printf ("  Flash erase aborted due to protected sectors\n");
+		return ERR_PROTECTED;
+	}
+
+	if ((s_first < info->sector_count) && (s_first <= s_last)) {
+		for (i = s_first; i <= s_last && !error; i++) {
+			printf ("  Erasing Sector %d @ 0x%08lx ... ", i,
+				info->start[i]);
+			/* bypass the cache to access the flash memory */
+			FLASH_CMD_ERASE_SEC (info->flash_id,
+					     (info->
+					      start[0] | CACHE_DISABLE_MASK),
+					     (info->
+					      start[i] | CACHE_DISABLE_MASK));
+			/* look for sector to become 0xFF after erase */
+			error = _flash_poll (info->flash_id,
+					     info->
+					     start[i] | CACHE_DISABLE_MASK,
+					     0xFF, CFG_FLASH_ERASE_TOUT);
+			FLASH_CMD_RESET (info->flash_id,
+					 (info->
+					  start[0] | CACHE_DISABLE_MASK));
+			printf ("done\n");
+			if (error) {
+				break;
+			}
+		}
+	} else
+		error = ERR_INVAL;
+
+	return error;
+}
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	u16 error = 0, i;
+	u32 n;
+	u8 *bp, *bps;
+
+	/*  Write Setup */
+	/* bypass the cache to access the flash memory */
+	FLASH_CMD_UNLOCK_BYPASS (info->flash_id,
+				 (info->start[0] | CACHE_DISABLE_MASK));
+
+	/*  Write the Data to Flash */
+
+	bp = (u8 *) (addr | CACHE_DISABLE_MASK);
+	bps = (u8 *) src;
+
+	for (n = 0; n < cnt && !error; n++, bp++, bps++) {
+
+		if (!(n % (cnt / 15))) {
+			printf (".");
+		}
+
+		/*  write the flash command for flash memory */
+		*bp = 0xA0;
+
+		/*  Write the data */
+		*bp = *bps;
+
+		/*  Check if the write is done */
+		for (i = 0; i < 0xff; i++);
+		error = _flash_poll (info->flash_id, (u32) bp, *bps,
+				     CFG_FLASH_WRITE_TOUT);
+		if (error) {
+			return error;
+		}
+	}
+
+	/*  Reset the Flash Mode to read */
+	FLASH_CMD_BYPASS_RESET (info->flash_id, info->start[0]);
+
+	printf (" ");
+
+	return error;
+}

board/evb4510/memsetup.S

@@ -0,0 +1,157 @@
+/*
+ * Copyright (c) 2004	Cucy Systems (http://www.cucy.com)
+ * Curt Brune <curt@cucy.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <config.h>
+#include <version.h>
+#include <asm/hardware.h>
+
+/***********************************************************************
+ * Configure Memory Map
+ *
+ * This memory map allows us to relocate from FLASH to SRAM.  After
+ * power-on reset the CPU only knows about the FLASH memory at address
+ * 0x00000000.	After memsetup completes the memory map will be:
+ *
+ * Memory Addr
+ * 0x00000000
+ *     to	8MB SRAM (U5) -- 8MB Map
+ * 0x00800000
+ *
+ * 0x01000000
+ *     to	2MB Flash @ 0x00000000 (U7) -- 2MB Map
+ * 0x01200000
+ *
+ * 0x02000000
+ *     to	512KB Flash @ 0x02000000 (U9) -- 2MB Map
+ * 0x02080000
+ *
+ * Load all 12 memory registers with the STMIA instruction since
+ * memory access is disabled once these registers are written.	The
+ * last register written re-enables memory access.  For more info see
+ * the user's manual for the S3C4510B, available from Samsung's web
+ * site.  Search for part number "S3C4510B".
+ *
+ ***********************************************************************/
+
+.globl memsetup
+memsetup:
+
+	/* preserve the temp register (r12 AKA ip) and remap it. */
+	ldr r1, =SRAM_BASE+0xC
+	add r0, r12, #0x01000000
+	str r0, [r1]
+
+	/* remap the link register for when we return */
+	add lr, lr, #0x01000000
+
+	/* store a short program in the on chip SRAM, which is
+	 * unaffected when remapping memory.  Note the cache must be
+	 * disabled for the on chip SRAM to be available.
+	 */
+	ldr r1, =SRAM_BASE
+	ldr r0, =0xe8801ffe  /* stmia r0, {r1-r12} */
+	str r0, [r1]
+	add r1, r1, #4
+	ldr r0, =0xe59fc000  /* ldr r12, [pc, #0]  */
+	str r0, [r1]
+	add r1, r1, #4
+	ldr r0, =0xe1a0f00e  /* mov pc, lr	   */
+	str r0, [r1]
+
+	adr   r0, memory_map_data
+	ldmia r0, {r1-r12}
+	ldr   r0, =REG_EXTDBWTH
+
+	ldr pc, =SRAM_BASE
+
+.globl reset_cpu
+reset_cpu:
+	/*
+	 * reset the cpu by re-mapping FLASH 0 to 0x0 and jumping to
+	 * address 0x0.	 We accomplish this by storing a few
+	 * instructions into the on chip SRAM (8KB) and run from
+	 * there.  Note the cache must be disabled for the on chip
+	 * SRAM to be available.
+	 *
+	 * load r2 with REG_ROMCON0
+	 * load r3 with 0x12040060	   configure FLASH bank 0 @ 0x00000000
+	 * load r4 with REG_DRAMCON0
+	 * load r5 with 0x08000380	   configure   RAM bank 0 @ 0x01000000
+	 * load r6 with REG_REFEXTCON
+	 * load r7 with 0x9c218360
+	 * load r8 with 0x0
+	 * store str r3,[r2] @ SRAM_BASE
+	 * store str r5,[r4] @ SRAM_BASE + 0x4
+	 * store str r7,[r6] @ SRAM_BASE + 0x8
+	 * store mov pc,r8   @ SRAM_BASE + 0xC
+	 * mov pc, SRAM_BASE
+	 *
+	 */
+
+	/* disable cache */
+	ldr r0, =REG_SYSCFG
+	ldr r1, =0x83ffffa0	/* cache-disabled  */
+	str r1, [r0]
+
+	ldr r2, =REG_ROMCON0
+	ldr r3, =0x02000060	/* Bank0 2MB FLASH   @ 0x00000000 */
+	ldr r4, =REG_DRAMCON0
+	ldr r5, =0x18040380	/* DRAM0 8MB SRAM    @ 0x01000000 */
+	ldr r6, =REG_REFEXTCON
+	ldr r7, =0xce278360
+	ldr r8, =0x00000000
+	ldr r1, =SRAM_BASE
+	ldr r0, =0xe5823000	/* str	r3, [r2] */
+	str r0, [r1]
+	ldr r1, =SRAM_BASE+4
+	ldr r0, =0xe5845000	/* str	r5, [r4] */
+	str r0, [r1]
+	ldr r1, =SRAM_BASE+8
+	ldr r0, =0xe5867000	/* str	r7, [r6] */
+	str r0, [r1]
+	ldr r1, =SRAM_BASE+0xC
+	ldr r0, =0xe1a0f008	/* mov	pc, r8	 */
+	str r0, [r1]
+	ldr r1, =SRAM_BASE
+	mov pc, r1
+
+	/* never return */
+
+/************************************************************************
+ * Below are twelve 32-bit values for the twelve memory registers of
+ * the system manager, starting with register REG_EXTDBWTH.
+ ***********************************************************************/
+memory_map_data:
+	.long 0x00f03005     /* memory widths */
+	.long 0x12040060     /* Bank0 2MB FLASH	  @ 0x01000000 */
+	.long 0x22080060     /* Bank1 512KB FLASH @ 0x02000000 */
+	.long 0x00000000
+	.long 0x00000000
+	.long 0x00000000
+	.long 0x00000000
+	.long 0x08000380     /* DRAM0 8MB SRAM	  @ 0x00000000 */
+	.long 0x00000000
+	.long 0x00000000
+	.long 0x00000000
+	.long 0x9c218360     /* enable memory */

board/evb4510/u-boot.lds

@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text	   :
+	{
+	  cpu/arm720t/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+				  /* Stabs debugging sections.	  */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

board/fads/config.mk

@@ -24,8 +24,8 @@
 #
 
 #
-# Motorola old MPC821/860ADS, MPC8xxFADS, new MPC866ADS, and DUET
-# (MPC87x/88x) ADS boards
+# Motorola old MPC821/860ADS, MPC8xxFADS, new MPC866ADS, and
+# MPC885ADS boards
 #
 
 TEXT_BASE = 0xFE000000

board/fads/fads.c

@@ -26,12 +26,13 @@
 #include <config.h>
 #include <common.h>
 #include <mpc8xx.h>
+#include <pcmcia.h>
 
 #define	_NOT_USED_	0xFFFFFFFF
 
 /* ========================================================================= */
 
-#ifndef CONFIG_DUET_ADS /* No old DRAM on Duet */
+#ifndef CONFIG_MPC885ADS /* No old DRAM on MPC885ADS */
 
 #if defined(CONFIG_DRAM_50MHZ)
 /* 50MHz tables */
@@ -290,7 +291,7 @@ static void _dramdisable(void)
 
 	/* maybe we should turn off upma here or something */
 }
-#endif /* !CONFIG_DUET_ADS */
+#endif /* !CONFIG_MPC885ADS */
 
 /* ========================================================================= */
 
@@ -604,7 +605,7 @@ long int initdram (int board_type)
 	uint sdramsz = 0;	/* size of sdram in Mbytes */
 	uint base = 0;		/* base of dram in bytes */
 	uint m = 0;		/* size of dram in Mbytes */
-#ifndef CONFIG_DUET_ADS
+#ifndef CONFIG_MPC885ADS
 	uint k, s;
 #endif
 
@@ -614,7 +615,7 @@ long int initdram (int board_type)
 		printf ("(%u MB SDRAM) ", sdramsz);
 	}
 #endif
-#ifndef CONFIG_DUET_ADS /* No old DRAM on Duet */
+#ifndef CONFIG_MPC885ADS /* No old DRAM on MPC885ADS */
 	k = (*((uint *) BCSR2) >> 23) & 0x0f;
 
 	switch (k & 0x3) {
@@ -665,7 +666,7 @@ long int initdram (int board_type)
 		_dramdisable ();
 		m = 0;
 	}
-#endif /* !CONFIG_DUET_ADS */
+#endif /* !CONFIG_MPC885ADS */
 	m += sdramsz;				/* add sdram size to total */
 
 	return (m << 20);
@@ -734,8 +735,8 @@ int checkboard (void)
 
 #if defined(CONFIG_MPC86xADS)
 	puts ("MPC86xADS");
-#elif defined(CONFIG_DUET_ADS)
-	puts ("DUET ADS");
+#elif defined(CONFIG_MPC885ADS)
+	puts ("MPC885ADS");
 	r = 0; /* I've got NR (No Revision) board */
 #elif defined(CONFIG_FADS)
 	puts ("FADS");
@@ -759,7 +760,7 @@ int checkboard (void)
 	case 0x03:
 		puts ("B \n");
 		break;
-#elif defined(CONFIG_DUET_ADS)
+#elif defined(CONFIG_MPC885ADS)
 	case 0x00:
 		puts ("NR\n");
 		break;
@@ -790,7 +791,7 @@ volatile unsigned char *pcmcia_mem = (unsigned char*)CFG_PCMCIA_MEM_ADDR;
 int pcmcia_init(void)
 {
 	volatile pcmconf8xx_t	*pcmp;
-	uint v, slota, slotb;
+	uint v, slota = 0, slotb = 0;
 
 	/*
 	** Enable the PCMCIA for a Flash card.
@@ -805,10 +806,10 @@ int pcmcia_init(void)
 	/* Set all slots to zero by default. */
 	pcmp->pcmc_pgcra = 0;
 	pcmp->pcmc_pgcrb = 0;
-#ifdef PCMCIA_SLOT_A
+#ifdef CONFIG_PCMCIA_SLOT_A
 	pcmp->pcmc_pgcra = 0x40;
 #endif
-#ifdef PCMCIA_SLOT_B
+#ifdef CONFIG_PCMCIA_SLOT_B
 	pcmp->pcmc_pgcrb = 0x40;
 #endif
 
@@ -817,17 +818,17 @@ int pcmcia_init(void)
 
 	/* Check if any PCMCIA card is plugged in. */
 
+#ifdef CONFIG_PCMCIA_SLOT_A
 	slota = (pcmp->pcmc_pipr & 0x18000000) == 0 ;
+#endif
+#ifdef CONFIG_PCMCIA_SLOT_B
 	slotb = (pcmp->pcmc_pipr & 0x00001800) == 0 ;
+#endif
 
 	if (!(slota || slotb)) {
 		printf("No card present\n");
-#ifdef PCMCIA_SLOT_A
 		pcmp->pcmc_pgcra = 0;
-#endif
-#ifdef PCMCIA_SLOT_B
 		pcmp->pcmc_pgcrb = 0;
-#endif
 		return -1;
 	}
 	else
@@ -908,9 +909,10 @@ int pcmcia_init(void)
 
 	udelay(20);
 
-#ifdef PCMCIA_SLOT_A
+#ifdef CONFIG_PCMCIA_SLOT_A
 	pcmp->pcmc_pgcra = 0;
-#elif PCMCIA_SLOT_B
+#endif
+#ifdef CONFIG_PCMCIA_SLOT_B
 	pcmp->pcmc_pgcrb = 0;
 #endif
 

board/fads/fads.h

@@ -48,9 +48,6 @@
  * | ...                   |                                 v
  *
  *****************************************************************************/
-/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
-/* in general, we always know this for FADS+new ADS anyway */
-#define CONFIG_8xx_GCLK_FREQ     ((CFG_8XX_XIN) * (CFG_8XX_FACT))
 
 #if 0
 #define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
@@ -66,6 +63,7 @@
     "bootm"
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+#define CONFIG_BZIP2	 /* include support for bzip2 compressed images */
 
 /*
  * New MPC86xADS and Duet provide two Ethernet connectivity options:
@@ -90,11 +88,13 @@
 #endif
 
 #ifndef CONFIG_COMMANDS
-#define CONFIG_COMMANDS	(CONFIG_CMD_DFL  \
-			 | CFG_CMD_DHCP  \
-			 | CFG_CMD_IMMAP \
-			 | CFG_CMD_MII   \
-			 | CFG_CMD_PING  \
+#define CONFIG_COMMANDS	(CONFIG_CMD_DFL   \
+			 | CFG_CMD_DHCP   \
+			 | CFG_CMD_IMMAP  \
+			 | CFG_CMD_JFFS2  \
+			 | CFG_CMD_MII    \
+			 | CFG_CMD_PCMCIA \
+			 | CFG_CMD_PING   \
 			)
 #endif /* !CONFIG_COMMANDS */
 
@@ -146,7 +146,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define	CFG_SDRAM_BASE		0x00000000
-#if defined(CONFIG_MPC86xADS) || defined(CONFIG_DUET_ADS) /* New ADS or Duet */
+#if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC885ADS) /* New ADS or Duet */
 #define	CFG_SDRAM_SIZE		0x00800000      	/* 8 Mbyte */
 #elif defined(CONFIG_FADS)				/* Old/new FADS */
 #define	CFG_SDRAM_SIZE		0x00400000		/* 4 Mbyte */
@@ -167,14 +167,24 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 KB for monitor	*/
+
+#ifdef CONFIG_BZIP2
+#define	CFG_MALLOC_LEN		(2500 << 10)	/* Reserve ~2.5 MB for malloc()	*/
+#else
+#define	CFG_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
+#endif /* CONFIG_BZIP2 */
+
 /*-----------------------------------------------------------------------
  * Flash organization
  */
-#define CFG_FLASH_BASE		TEXT_BASE
-#define CFG_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
+#define CFG_FLASH_BASE		CFG_MONITOR_BASE
+#define CFG_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte	*/
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	16      /* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	4	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
@@ -184,9 +194,14 @@
 #define CFG_ENV_OFFSET		CFG_ENV_SECT_SIZE
 #define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment		*/
 
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 KB for monitor	*/
-#define	CFG_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
+#define	CFG_DIRECT_FLASH_TFTP
+
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2)
+#define CFG_JFFS2_FIRST_BANK	0
+#define CFG_JFFS2_NUM_BANKS	CFG_MAX_FLASH_BANKS
+#define CFG_JFFS2_FIRST_SECTOR  4
+#define CFG_JFFS2_SORT_FRAGMENTS
+#endif /* CFG_CMD_JFFS2 */
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
@@ -248,7 +263,16 @@
 #define SCCR_MASK	SCCR_EBDF11
 #define CFG_SCCR	(SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
 
- /*-----------------------------------------------------------------------
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		14-22
+ *-----------------------------------------------------------------------
+ * set the PLL, the low-power modes and the reset control
+ */
+#ifndef CFG_PLPRCR
+#define CFG_PLPRCR	PLPRCR_TEXPS
+#endif
+
+/*-----------------------------------------------------------------------
  *
  *-----------------------------------------------------------------------
  *
@@ -339,6 +363,7 @@
 #define BCSR1_PCCVCCON		 BCSR1_PCCVCC0
 
 #define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
+#define BCSR2_FLASH_PD_SHIFT     28
 #define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
 #define BCSR2_DRAM_PD_SHIFT      23
 #define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
@@ -407,6 +432,20 @@
 #define BCSR4_DATA_VOICE         ((uint)0x00080000)
 #endif /* CONFIG_MPC850 */
 
+/* BSCR5 exists on MPC86xADS and Duet ADS only */
+
+#define CFG_PHYDEV_ADDR		(BCSR_ADDR + 0x20000)
+
+#define BCSR5			(CFG_PHYDEV_ADDR + 0x300)
+
+#define BCSR5_MII2_EN		0x40
+#define BCSR5_MII2_RST		0x20
+#define BCSR5_T1_RST		0x10
+#define BCSR5_ATM155_RST	0x08
+#define BCSR5_ATM25_RST		0x04
+#define BCSR5_MII1_EN		0x02
+#define BCSR5_MII1_RST		0x01
+
 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0
@@ -419,10 +458,6 @@
  * PCMCIA stuff
  *-----------------------------------------------------------------------
  */
-#if !defined(CONFIG_MPC823) && !defined(CONFIG_MPC850)
-#define PCMCIA_SLOT_A 1
-#endif
-
 #define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
 #define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
 #define CFG_PCMCIA_DMA_ADDR	(0xE4000000)

board/fads/flash.c

@@ -24,7 +24,7 @@
 #include <common.h>
 #include <mpc8xx.h>
 
-flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips        */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips */
 
 #if defined(CFG_ENV_IS_IN_FLASH)
 # ifndef  CFG_ENV_ADDR
@@ -38,124 +38,103 @@ flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips        */
 # endif
 #endif
 
+#define QUAD_ID(id)	((((ulong)(id) & 0xFF) << 24) | \
+			 (((ulong)(id) & 0xFF) << 16) | \
+			 (((ulong)(id) & 0xFF) << 8)  | \
+			 (((ulong)(id) & 0xFF) << 0)    \
+			)
+
 /*-----------------------------------------------------------------------
  * Functions
  */
 static ulong flash_get_size (vu_long * addr, flash_info_t * info);
 static int write_word (flash_info_t * info, ulong dest, ulong data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
 
 /*-----------------------------------------------------------------------
  */
-
 unsigned long flash_init (void)
 {
 	volatile immap_t *immap = (immap_t *) CFG_IMMR;
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
-	unsigned long total_size;
-	unsigned long size_b0, size_b1;
+	vu_long *bcsr = (vu_long *)BCSR_ADDR;
+	unsigned long pd_size, total_size, bsize, or_am;
 	int i;
 
 	/* Init: no FLASHes known */
 	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
 		flash_info[i].flash_id = FLASH_UNKNOWN;
+		flash_info[i].size = 0;
+		flash_info[i].sector_count = 0;
+		flash_info[i].start[0] = 0xFFFFFFFF; /* For TFTP */
+	}
+
+	switch ((bcsr[2] & BCSR2_FLASH_PD_MASK) >> BCSR2_FLASH_PD_SHIFT) {
+	case 2:
+	case 4:
+	case 6:
+		pd_size = 0x800000;
+		or_am = 0xFF800000;
+		break;
+
+	case 5:
+	case 7:
+		pd_size = 0x400000;
+		or_am = 0xFFC00000;
+		break;
+
+	case 8:
+		pd_size = 0x200000;
+		or_am = 0xFFE00000;
+		break;
+
+	default:
+		pd_size = 0;
+		or_am = 0xFFE00000;
+		printf("## Unsupported flash detected by BCSR: 0x%08X\n", bcsr[2]);
 	}
 
 	total_size = 0;
-	size_b0 = 0xffffffff;
-
-	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
-		size_b1 =
-			flash_get_size ((vu_long *) (CFG_FLASH_BASE +
-						     total_size),
-					&flash_info[i]);
+	for (i = 0; i < CFG_MAX_FLASH_BANKS && total_size < pd_size; ++i) {
+		bsize = flash_get_size((vu_long *)(CFG_FLASH_BASE + total_size),
+				       &flash_info[i]);
 
 		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
-			printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n", i, size_b1, size_b1 >> 20);
+			printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
+				i, bsize, bsize >> 20);
 		}
 
-		/* Is this really needed ? - LP */
-		if (size_b1 > size_b0) {
-			printf ("## ERROR: Bank %d (0x%08lx = %ld MB) > Bank %d (0x%08lx = %ld MB)\n", i, size_b1, size_b1 >> 20, i - 1, size_b0, size_b0 >> 20);
-			goto out_error;
-		}
-		size_b0 = size_b1;
-		total_size += size_b1;
+		total_size += bsize;
 	}
 
-	/* Compute the Address Mask */
-	for (i = 0; (total_size >> i) != 0; ++i) {
-	}
-	i--;
-
-	if (total_size != (1 << i)) {
-		printf ("## WARNING: Total FLASH size (0x%08lx = %ld MB) is not a power of 2\n", total_size, total_size >> 20);
+	if (total_size != pd_size) {
+		printf("## Detected flash size %lu conflicts with PD data %lu\n",
+		       total_size, pd_size);
 	}
 
 	/* Remap FLASH according to real size */
-	memctl->memc_or0 =
-		((((unsigned long) ~1) << i) & OR_AM_MSK) |
-		CFG_OR_TIMING_FLASH;
-	memctl->memc_br0 = CFG_BR0_PRELIM;
-
-	total_size = 0;
+	memctl->memc_or0 = or_am | CFG_OR_TIMING_FLASH;
 
 	for (i = 0; i < CFG_MAX_FLASH_BANKS && flash_info[i].size != 0; ++i) {
-		/* Re-do sizing to get full correct info */
-		/* Why ? - LP */
-		size_b1 =
-			flash_get_size ((vu_long *) (CFG_FLASH_BASE +
-						     total_size),
-					&flash_info[i]);
-
-		/* This is done by flash_get_size - LP */
-		/* flash_get_offsets (CFG_FLASH_BASE + total_size, &flash_info[i]); */
-
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE
 		/* monitor protection ON by default */
-		flash_protect (FLAG_PROTECT_SET,
-			       CFG_MONITOR_BASE,
-			       CFG_MONITOR_BASE + monitor_flash_len - 1,
-			       &flash_info[i]);
+		if (CFG_MONITOR_BASE >= flash_info[i].start[0])
+			flash_protect (FLAG_PROTECT_SET,
+				       CFG_MONITOR_BASE,
+				       CFG_MONITOR_BASE + monitor_flash_len - 1,
+				       &flash_info[i]);
 #endif
 
 #ifdef	CFG_ENV_IS_IN_FLASH
 		/* ENV protection ON by default */
-		flash_protect (FLAG_PROTECT_SET,
-			       CFG_ENV_ADDR,
-			       CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
-			       &flash_info[i]);
+		if (CFG_ENV_ADDR >= flash_info[i].start[0])
+			flash_protect (FLAG_PROTECT_SET,
+				       CFG_ENV_ADDR,
+				       CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
+				       &flash_info[i]);
 #endif
-
-		total_size += size_b1;
 	}
 
-	return (total_size);
-
-      out_error:
-	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-		flash_info[i].sector_count = -1;
-		flash_info[i].size = 0;
-	}
-
-	return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
-	int i;
-
-	/* set up sector start address table */
-	if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040
-	    || (info->flash_id & FLASH_TYPEMASK) == FLASH_AM080) {
-		/* set sector offsets for uniform sector type   */
-		for (i = 0; i < info->sector_count; i++) {
-			info->start[i] = base + (i * 0x00040000);
-		}
-	}
+	return total_size;
 }
 
 /*-----------------------------------------------------------------------
@@ -235,48 +214,26 @@ void flash_print_info (flash_info_t * info)
 	}
 
 	printf ("\n");
-	return;
 }
 
 /*-----------------------------------------------------------------------
+ * The following code can not run from flash!
  */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
 static ulong flash_get_size (vu_long * addr, flash_info_t * info)
 {
 	short i;
 
-#if 0
-	ulong base = (ulong) addr;
-#endif
-	uchar value;
-
 	/* Write auto select command: read Manufacturer ID */
-#if 0
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00900090;
-#else
 	addr[0x0555] = 0xAAAAAAAA;
 	addr[0x02AA] = 0x55555555;
 	addr[0x0555] = 0x90909090;
-#endif
 
-	value = addr[0];
-
-	switch (value + (value << 16)) {
-	case AMD_MANUFACT:
+	switch (addr[0]) {
+	case QUAD_ID(AMD_MANUFACT):
 		info->flash_id = FLASH_MAN_AMD;
 		break;
 
-	case FUJ_MANUFACT:
+	case QUAD_ID(FUJ_MANUFACT):
 		info->flash_id = FLASH_MAN_FUJ;
 		break;
 
@@ -287,21 +244,20 @@ static ulong flash_get_size (vu_long * addr, flash_info_t * info)
 		break;
 	}
 
-	value = addr[1];	/* device ID            */
-
-	switch (value) {
-	case AMD_ID_F040B:
+	switch (addr[1]) {	/* device ID            */
+	case QUAD_ID(AMD_ID_F040B):
+	case QUAD_ID(AMD_ID_LV040B):
 		info->flash_id += FLASH_AM040;
 		info->sector_count = 8;
 		info->size = 0x00200000;
 		break;		/* => 2 MB              */
 
-	case AMD_ID_F080B:
+	case QUAD_ID(AMD_ID_F080B):
 		info->flash_id += FLASH_AM080;
 		info->sector_count = 16;
 		info->size = 0x00400000;
 		break;		/* => 4 MB              */
-
+#if 0
 	case AMD_ID_LV400T:
 		info->flash_id += FLASH_AM400T;
 		info->sector_count = 11;
@@ -337,7 +293,7 @@ static ulong flash_get_size (vu_long * addr, flash_info_t * info)
 		info->sector_count = 35;
 		info->size = 0x00400000;
 		break;		/* => 4 MB              */
-#if 0				/* enable when device IDs are available */
+
 	case AMD_ID_LV320T:
 		info->flash_id += FLASH_AM320T;
 		info->sector_count = 67;
@@ -349,11 +305,10 @@ static ulong flash_get_size (vu_long * addr, flash_info_t * info)
 		info->sector_count = 67;
 		info->size = 0x00800000;
 		break;		/* => 8 MB              */
-#endif
+#endif /* 0 */
 	default:
 		info->flash_id = FLASH_UNKNOWN;
 		return (0);	/* => no or unknown flash */
-
 	}
 
 #if 0
@@ -378,7 +333,9 @@ static ulong flash_get_size (vu_long * addr, flash_info_t * info)
 		}
 	}
 #else
-	flash_get_offsets ((ulong) addr, info);
+	/* set sector offsets for uniform sector type */
+	for (i = 0; i < info->sector_count; i++)
+		info->start[i] = (ulong)addr + (i * 0x00040000);
 #endif
 
 	/* check for protected sectors */
@@ -389,25 +346,16 @@ static ulong flash_get_size (vu_long * addr, flash_info_t * info)
 		info->protect[i] = addr[2] & 1;
 	}
 
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
 	if (info->flash_id != FLASH_UNKNOWN) {
 		addr = (volatile unsigned long *) info->start[0];
-#if 0
-		*addr = 0x00F000F0;	/* reset bank */
-#else
 		*addr = 0xF0F0F0F0;	/* reset bank */
-#endif
 	}
 
 	return (info->size);
 }
 
-
 /*-----------------------------------------------------------------------
  */
-
 int flash_erase (flash_info_t * info, int s_first, int s_last)
 {
 	vu_long *addr = (vu_long *) (info->start[0]);
@@ -420,13 +368,13 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 		} else {
 			printf ("- no sectors to erase\n");
 		}
-		return 1;
+		return ERR_INVAL;
 	}
 
 	if ((info->flash_id == FLASH_UNKNOWN) ||
 	    (info->flash_id > FLASH_AMD_COMP)) {
 		printf ("Can't erase unknown flash type - aborted\n");
-		return 1;
+		return ERR_UNKNOWN_FLASH_TYPE;
 	}
 
 	prot = 0;
@@ -447,29 +395,17 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	/* Disable interrupts which might cause a timeout here */
 	flag = disable_interrupts ();
 
-#if 0
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00800080;
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-#else
 	addr[0x0555] = 0xAAAAAAAA;
 	addr[0x02AA] = 0x55555555;
 	addr[0x0555] = 0x80808080;
 	addr[0x0555] = 0xAAAAAAAA;
 	addr[0x02AA] = 0x55555555;
-#endif
 
 	/* Start erase on unprotected sectors */
 	for (sect = s_first; sect <= s_last; sect++) {
 		if (info->protect[sect] == 0) {	/* not protected */
 			addr = (vu_long *) (info->start[sect]);
-#if 0
-			addr[0] = 0x00300030;
-#else
 			addr[0] = 0x30303030;
-#endif
 			l_sect = sect;
 		}
 	}
@@ -490,15 +426,11 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	start = get_timer (0);
 	last = start;
 	addr = (vu_long *) (info->start[l_sect]);
-#if 0
-	while ((addr[0] & 0x00800080) != 0x00800080)
-#else
 	while ((addr[0] & 0xFFFFFFFF) != 0xFFFFFFFF)
-#endif
 	{
 		if ((now = get_timer (start)) > CFG_FLASH_ERASE_TOUT) {
 			printf ("Timeout\n");
-			return 1;
+			return ERR_TIMOUT;
 		}
 		/* show that we're waiting */
 		if ((now - last) > 1000) {	/* every second */
@@ -510,13 +442,10 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
       DONE:
 	/* reset to read mode */
 	addr = (volatile unsigned long *) info->start[0];
-#if 0
-	addr[0] = 0x00F000F0;	/* reset bank */
-#else
 	addr[0] = 0xF0F0F0F0;	/* reset bank */
-#endif
 
 	printf (" done\n");
+
 	return 0;
 }
 
@@ -526,7 +455,6 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
  * 1 - write timeout
  * 2 - Flash not erased
  */
-
 int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
 {
 	ulong cp, wp, data;
@@ -605,20 +533,14 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 
 	/* Check if Flash is (sufficiently) erased */
 	if ((*((vu_long *) dest) & data) != data) {
-		return (2);
+		return ERR_NOT_ERASED;
 	}
 	/* Disable interrupts which might cause a timeout here */
 	flag = disable_interrupts ();
 
-#if 0
-	addr[0x0555] = 0x00AA00AA;
-	addr[0x02AA] = 0x00550055;
-	addr[0x0555] = 0x00A000A0;
-#else
 	addr[0x0555] = 0xAAAAAAAA;
 	addr[0x02AA] = 0x55555555;
 	addr[0x0555] = 0xA0A0A0A0;
-#endif
 
 	*((vu_long *) dest) = data;
 
@@ -628,18 +550,11 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 
 	/* data polling for D7 */
 	start = get_timer (0);
-#if 0
-	while ((*((vu_long *) dest) & 0x00800080) != (data & 0x00800080))
-#else
 	while ((*((vu_long *) dest) & 0x80808080) != (data & 0x80808080))
-#endif
 	{
 		if (get_timer (start) > CFG_FLASH_WRITE_TOUT) {
-			return (1);
+			return ERR_TIMOUT;
 		}
 	}
 	return (0);
 }
-
-/*-----------------------------------------------------------------------
- */

board/fads/u-boot.lds

@@ -52,7 +52,7 @@ SECTIONS
   {
     cpu/mpc8xx/start.o		(.text)
 
-    . = DEFINED(env_offset) ? env_offset : .;
+    /*. = DEFINED(env_offset) ? env_offset : .;*/
     common/environment.o	(.ppcenv)
 
     *(.text)

board/gcplus/Makefile

@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# 2003 (c) MontaVista Software, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= gcplus.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/gcplus/config.mk

@@ -0,0 +1,13 @@
+#
+# ADS GCPlus board with SA1110 cpu
+#
+# The ADS GCPlus has 2 banks of 16 MiB SDRAM
+#
+# We use the ADS GCPlus Linux boot ROM to load U-Boot into SDRAM
+# at c020'0000 and then move ourself to c8f0'0000. Basically, just
+# install the U-Boot binary as you would the Linux zImage and then
+# reap the benfits of more convenient Linux development cycles, i.e.
+# bootp;tftp;bootm, repeat, etc.,.
+#
+
+TEXT_BASE = 0xc8f00000

board/gcplus/flash.c

@@ -0,0 +1,440 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * 2003 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips */
+
+/* Board support for 1 or 2 flash devices */
+#define FLASH_PORT_WIDTH32
+#undef FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)				__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)				__swab32(x)
+#endif
+
+#define FPW				FLASH_PORT_WIDTH
+#define FPWV				FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size(FPW * addr, flash_info_t * info);
+static int write_data(flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets(ulong base, flash_info_t * info);
+void inline spin_wheel(void);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long
+flash_init(void)
+{
+	int i;
+	ulong size = 0;
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets(PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_FLASH_BASE,
+		      CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_ENV_ADDR,
+		      CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void
+flash_get_offsets(ulong base, flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
+			info->protect[i] = 0;
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void
+flash_print_info(flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf("INTEL ");
+		break;
+	default:
+		printf("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F128J3A:
+		printf("28F128J3A\n");
+		break;
+	case FLASH_28F640J5:
+		printf("28F640J5\n");
+		break;
+	default:
+		printf("Unknown Chip Type\n");
+		break;
+	}
+
+	printf("  Size: %ld MB in %d Sectors\n",
+	       info->size >> 20, info->sector_count);
+
+	printf("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf("\n   ");
+		printf(" %08lX%s",
+		       info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong
+flash_get_size(FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);	/* no or unknown flash  */
+	}
+
+	mb();
+	value = addr[1];	/* device ID            */
+	switch (value) {
+	case (FPW) INTEL_ID_28F128J3A:
+		info->flash_id += FLASH_28F128J3A;
+		info->sector_count = 128;
+		info->size = 0x02000000;
+		break;		/* => 16 MB     */
+	case (FPW) INTEL_ID_28F640J5:
+		info->flash_id += FLASH_28F640J5;
+		info->sector_count = 64;
+		info->size = 0x01000000;
+		break;		/* => 16 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf("** ERROR: sector count %d > max (%d) **\n",
+		       info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int
+flash_erase(flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf("- missing\n");
+		} else {
+			printf("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf("Can't erase unknown flash type %08lx - aborted\n",
+		       info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf("- Warning: %d protected sectors will not be erased!\n",
+		       prot);
+	} else {
+		printf("\n");
+	}
+
+	start = get_timer(0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf("Erasing sector %2d ... ", sect);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked();
+
+			*addr = (FPW) 0x00500050;	/* clear status register */
+			*addr = (FPW) 0x00200020;	/* erase setup */
+			*addr = (FPW) 0x00D000D0;	/* erase confirm */
+
+			while (((status =
+				 *addr) & (FPW) 0x00800080) !=
+			       (FPW) 0x00800080) {
+				if (get_timer_masked() > CFG_FLASH_ERASE_TOUT) {
+					printf("Timeout\n");
+					*addr = (FPW) 0x00B000B0;	/* suspend erase         */
+					*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
+					rcode = 1;
+					break;
+				}
+			}
+
+			*addr = (FPW) 0x00500050;	/* clear status register cmd.   */
+			*addr = (FPW) 0x00FF00FF;	/* resest to read mode          */
+
+			printf(" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int
+write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data(info, wp, SWAP(data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data(info, wp, SWAP(data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data(info, wp, SWAP(data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int
+write_data(flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf("not erased at %08lX (%lX)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked() > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (0);
+}
+
+void inline
+spin_wheel(void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}

board/gcplus/gcplus.c

@@ -0,0 +1,73 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * 2003-2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <SA-1100.h>
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int
+board_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_arch_number = 29;	/* ADS GraphicsClientPlus Board */
+
+	gd->bd->bi_boot_params = 0xc000003c; /* Weird address? */
+
+	/* Most of the ADS GCPlus I/O is connected to Static nCS2.
+	 * So I'm brute forcing nCS2 timiming here for worst case.
+	 */
+	MSC1 &= ~0xFFFF;
+	MSC1 |= 0x8649;
+
+	/* Nothing is connected to Static nCS4 or nCS5. But I'm using
+	 * nCS4 as a paranoia safe guard to force nCS2, nOE; nWE high
+	 * after accessing I/O via (non-VLIO) nCS2. What can I say, I'm
+	 * paranoid and lack decent tools to alleviate my fear. I sure
+	 * do wish I had a logic analyzer. : (
+	 */
+
+	MSC2 =  0xfff9fff9;
+
+	return 0;
+}
+
+int
+dram_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+
+	return (0);
+}

board/gcplus/memsetup.S

@@ -0,0 +1,77 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
+ *                     Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
+ * 2003-2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include "config.h"
+#include "version.h"
+
+
+	.globl	memsetup
+memsetup:
+	/* The ADS GC+ for Linux Boot Rom Ver. 1.73 does memory init for us.
+	 * However the darn thing leaves the MMU enabled before handing control
+	 * over to us. So we need to disable the MMU and we use memsetup
+	 * to do it.
+	 */
+
+@ The following code segment was borrowed with gratitude from:
+@	linux-2.4.19-rmk7/arch/arm/boot/compressed/head-sa1100.S
+
+	@ Data cache might be active.
+	@ Be sure to flush kernel binary out of the cache,
+	@ whatever state it is, before it is turned off.
+	@ This is done by fetching through currently executed
+	@ memory to be sure we hit the same cache.
+	bic	r2, pc, #0x1f
+	add	r3, r2, #0x4000		@ 16 kb is quite enough...
+1:	ldr	r0, [r2], #32
+	teq	r2, r3
+	bne	1b
+	mcr	p15, 0, r0, c7, c10, 4	@ drain WB
+	mcr	p15, 0, r0, c7, c7, 0	@ flush I & D caches
+
+	@ disabling MMU and caches
+	mrc	p15, 0, r0, c1, c0, 0	@ read control reg
+	bic	r0, r0, #0x0d		@ clear WB, DC, MMU
+	bic	r0, r0, #0x1000		@ clear Icache
+	mcr	p15, 0, r0, c1, c0, 0
+
+	nop
+	nop
+	nop
+	nop
+	nop
+
+	b	2f
+2:
+	nop
+	nop
+	nop
+	nop
+	nop
+
+
+	mov	pc, lr

board/gcplus/u-boot.lds

@@ -0,0 +1,57 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * 2003 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+		cpu/sa1100/start.o	(.text)
+		*(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/icecube/icecube.c

@@ -2,6 +2,9 @@
  * (C) Copyright 2003
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
@@ -25,90 +28,84 @@
 #include <mpc5xxx.h>
 #include <pci.h>
 
+#if defined(CONFIG_MPC5200_DDR)
+#include "mt46v16m16-75.h"
+#else
+#include "mt48lc16m16a2-75.h"
+#endif
+
 #ifndef CFG_RAMBOOT
 static void sdram_start (int hi_addr)
 {
 	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
 
-#ifdef CONFIG_MPC5200_DDR
 	/* unlock mode register */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f00 | hi_addr_bit;
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
 	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f02 | hi_addr_bit;
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+#if SDRAM_DDR
 	/* set mode register: extended mode */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x40090000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+	__asm__ volatile ("sync");
+
 	/* set mode register: reset DLL */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x058d0000;
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f02 | hi_addr_bit;
-	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f04 | hi_addr_bit;
-	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x018d0000;
-	/* normal operation */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0x705f0f00 | hi_addr_bit;
-#else
-	/* unlock mode register */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0000 | hi_addr_bit;
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0002 | hi_addr_bit;
-	/* set mode register */
-#if defined(CONFIG_MPC5200)
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
-#elif defined(CONFIG_MGT5100)
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x008d0000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+	__asm__ volatile ("sync");
 #endif
+
+	/* precharge all banks */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
 	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
-	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
 	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+	__asm__ volatile ("sync");
+
 	/* normal operation */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0x504f0000 | hi_addr_bit;
-#endif
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+	__asm__ volatile ("sync");
 }
 #endif
 
+/*
+ * ATTENTION: Although partially referenced initdram does NOT make real use
+ *            use of CFG_SDRAM_BASE. The code does not work if CFG_SDRAM_BASE
+ *            is something else than 0x00000000.
+ */
+
+#if defined(CONFIG_MPC5200)
 long int initdram (int board_type)
 {
 	ulong dramsize = 0;
-#ifdef CONFIG_MPC5200_DDR
 	ulong dramsize2 = 0;
-#endif
 #ifndef CFG_RAMBOOT
 	ulong test1, test2;
 
-	/* configure SDRAM start/end */
-#if defined(CONFIG_MPC5200)
+	/* setup SDRAM chip selects */
 	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
 	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
+	__asm__ volatile ("sync");
 
-#ifdef CONFIG_MPC5200_DDR
 	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0x73722930;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x47770000;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+	__asm__ volatile ("sync");
 
-	/* set tap delay to 0x10 */
-	*(vu_long *)MPC5XXX_CDM_PORCFG = 0x10000000;
-#else
-	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xd2322800;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x8ad70000;
+#if SDRAM_DDR
+	/* set tap delay */
+	*(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+	__asm__ volatile ("sync");
 #endif
 
-#elif defined(CONFIG_MGT5100)
-	*(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
-	*(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
-	*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
-
-	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xc2222600;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x88b70004;
-
-	/* address select register */
-	*(vu_long *)MPC5XXX_SDRAM_XLBSEL = 0x03000000;
-#endif
+	/* find RAM size using SDRAM CS0 only */
 	sdram_start(0);
 	test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
 	sdram_start(1);
@@ -119,11 +116,23 @@ long int initdram (int board_type)
 	} else {
 		dramsize = test2;
 	}
-#if defined(CONFIG_MPC5200)
-	*(vu_long *)MPC5XXX_SDRAM_CS0CFG =
-		(0x13 + __builtin_ffs(dramsize >> 20) - 1);
-#ifdef CONFIG_MPC5200_DDR
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize < (1 << 20)) {
+		dramsize = 0;
+	}
+
+	/* set SDRAM CS0 size according to the amount of RAM found */
+	if (dramsize > 0) {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
+	} else {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+	}
+
+	/* let SDRAM CS1 start right after CS0 */
 	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
+
+	/* find RAM size using SDRAM CS1 only */
 	sdram_start(0);
 	test1 = get_ram_size((ulong *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
 	sdram_start(1);
@@ -134,34 +143,94 @@ long int initdram (int board_type)
 	} else {
 		dramsize2 = test2;
 	}
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG =
-		dramsize + (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
-#else
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-#endif
-#elif defined(CONFIG_MGT5100)
-	*(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
-#endif
 
-#else	/* CFG_RAMBOOT */
-#ifdef CONFIG_MGT5100
-	*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
-	dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
-#else
-	dramsize = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS0CFG - 0x13)) << 20);
-#ifdef CONFIG_MPC5200_DDR
-	dramsize2 = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS1CFG - 0x13)) << 20);
-#endif
-#endif
+	/* memory smaller than 1MB is impossible */
+	if (dramsize2 < (1 << 20)) {
+		dramsize2 = 0;
+	}
+
+	/* set SDRAM CS1 size according to the amount of RAM found */
+	if (dramsize2 > 0) {
+		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
+			| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
+	} else {
+		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+	}
+
+#else /* CFG_RAMBOOT */
+
+	/* retrieve size of memory connected to SDRAM CS0 */
+	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+	if (dramsize >= 0x13) {
+		dramsize = (1 << (dramsize - 0x13)) << 20;
+	} else {
+		dramsize = 0;
+	}
+
+	/* retrieve size of memory connected to SDRAM CS1 */
+	dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
+	if (dramsize2 >= 0x13) {
+		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+	} else {
+		dramsize2 = 0;
+	}
+
+#endif /* CFG_RAMBOOT */
+
+	return dramsize + dramsize2;
+}
+
+#elif defined(CONFIG_MGT5100)
+
+long int initdram (int board_type)
+{
+	ulong dramsize = 0;
+#ifndef CFG_RAMBOOT
+	ulong test1, test2;
+
+	/* setup and enable SDRAM chip selects */
+	*(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
+	*(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
+	*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
+	__asm__ volatile ("sync");
+
+	/* setup config registers */
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+
+	/* address select register */
+	*(vu_long *)MPC5XXX_SDRAM_XLBSEL = SDRAM_ADDRSEL;
+	__asm__ volatile ("sync");
+
+	/* find RAM size */
+	sdram_start(0);
+	test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+	sdram_start(1);
+	test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize = test1;
+	} else {
+		dramsize = test2;
+	}
+
+	/* set SDRAM end address according to size */
+	*(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
+
+#else /* CFG_RAMBOOT */
+
+	/* Retrieve amount of SDRAM available */
+	dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
+
 #endif /* CFG_RAMBOOT */
 
-#ifdef CONFIG_MPC5200_DDR
-	dramsize += dramsize2;
-#endif
-	/* return total ram size */
 	return dramsize;
 }
 
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif
+
 int checkboard (void)
 {
 #if defined(CONFIG_MPC5200)
@@ -207,3 +276,28 @@ void pci_init_board(void)
 	pci_mpc5xxx_init(&hose);
 }
 #endif
+
+#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+
+#define GPIO_PSC1_4	0x01000000UL
+
+void init_ide_reset (void)
+{
+	debug ("init_ide_reset\n");
+
+    	/* Configure PSC1_4 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
+}
+
+void ide_set_reset (int idereset)
+{
+	debug ("ide_reset(%d)\n", idereset);
+
+	if (idereset) {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
+	} else {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA |=  GPIO_PSC1_4;
+	}
+}
+#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */

board/icecube/mt46v16m16-75.h

@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	1		/* is DDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x018D0000
+#define SDRAM_EMODE	0x40090000
+#define SDRAM_CONTROL	0x705f0f00
+#define SDRAM_CONFIG1	0x73722930
+#define SDRAM_CONFIG2	0x47770000
+#define SDRAM_TAPDELAY	0x10000000
+
+#else
+#error CONFIG_MPC5200 not defined
+#endif

board/icecube/mt48lc16m16a2-75.h

@@ -0,0 +1,43 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	0		/* is SDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x00CD0000
+#define SDRAM_CONTROL	0x504F0000
+#define SDRAM_CONFIG1	0xD2322800
+#define SDRAM_CONFIG2	0x8AD70000
+
+#elif defined(CONFIG_MGT5100)
+/* Settings for XLB = 66 MHz */
+#define SDRAM_MODE	0x008D0000
+#define SDRAM_CONTROL	0x504F0000
+#define SDRAM_CONFIG1	0xC2222600
+#define SDRAM_CONFIG2	0x88B70004
+#define SDRAM_ADDRSEL	0x02000000
+
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif

board/integratorap/Makefile

@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2004
+# ARM Ltd.
+# Philippe Robin, <philippe.robin@arm.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= integratorap.o flash.o
+SOBJS	:= platform.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/integratorap/config.mk

@@ -0,0 +1,5 @@
+#
+# image should be loaded at 0x01000000
+#
+
+TEXT_BASE = 0x01000000

board/integratorap/flash.c

@@ -0,0 +1,473 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)			__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)			__swab32(x)
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+	unsigned int sector_number;
+	unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
+	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+	int i;
+	OrgDef *pOrgDef;
+
+	pOrgDef = OrgIntel_28F256L18T;
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			if (i > 255) {
+				info->start[i] = base + (i * 0x8000);
+				info->protect[i] = 0;
+			} else {
+				info->start[i] = base +
+						(i * PHYS_FLASH_SECT_SIZE);
+				info->protect[i] = 0;
+			}
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F256L18T:
+		printf ("FLASH 28F256L18T\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);		/* no or unknown flash  */
+	}
+
+	mb ();
+	value = addr[1];	/* device ID        */
+	switch (value) {
+
+	case (FPW) (INTEL_ID_28F256L18T):
+		info->flash_id += FLASH_28F256L18T;
+		info->sector_count = 259;
+		info->size = 0x02000000;
+		break;			/* => 32 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+				info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK    0x0080
+
+	*addr = (FPW) 0x00500050;	/* clear status register */
+
+	/* this sends the clear lock bit command */
+	*addr = (FPW) 0x00600060;
+	*addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+				info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+				prot);
+	} else {
+		printf ("\n");
+	}
+
+
+	start = get_timer (0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			flash_unprotect_sectors (addr);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;/* clear status register */
+			*addr = (FPW) 0x00200020;/* erase setup */
+			*addr = (FPW) 0x00D000D0;/* erase confirm */
+
+			while (((status =
+				*addr) & (FPW) 0x00800080) !=
+				(FPW) 0x00800080) {
+					if (get_timer_masked () >
+					CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					/* suspend erase     */
+					*addr = (FPW) 0x00B000B0;
+					/* reset to read mode */
+					*addr = (FPW) 0x00FF00FF;
+					rcode = 1;
+					break;
+				}
+			}
+
+			/* clear status register cmd.   */
+			*addr = (FPW) 0x00500050;
+			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	flash_unprotect_sectors (addr);
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}

board/integratorap/integratorap.c

@@ -0,0 +1,479 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * (C) Copyright 2004
+ * ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_PCI
+#   include <pci.h>
+#endif
+
+void flash__init (void);
+void ether__init (void);
+void peripheral_power_enable (void);
+
+#if defined(CONFIG_SHOW_BOOT_PROGRESS)
+void show_boot_progress(int progress)
+{
+    printf("Boot reached stage %d\n", progress);
+}
+#endif
+
+#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
+
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+		"subs %0, %1, #1\n"
+		"bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* arch number of Integrator Board */
+	gd->bd->bi_arch_number = 21;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x00000100;
+
+	gd->flags = 0;
+
+	icache_enable ();
+
+	flash__init ();
+	return 0;
+}
+
+
+int misc_init_r (void)
+{
+#ifdef CONFIG_PCI
+	pci_init();
+#endif
+	setenv("verify", "n");
+	return (0);
+}
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+#ifdef CONFIG_PCI
+
+#ifndef CONFIG_PCI_PNP
+
+static struct pci_config_table pci_integrator_config_table[] = {
+	{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
+	  pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				       PCI_ENET0_MEMADDR,
+				       PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
+	{ }
+};
+#endif
+
+/* V3 access routines */
+#define _V3Write16(o,v) (*(volatile unsigned short *)(PCI_V3_BASE + (unsigned int)(o)) = (unsigned short)(v))
+#define _V3Read16(o)    (*(volatile unsigned short *)(PCI_V3_BASE + (unsigned int)(o)))
+
+#define _V3Write32(o,v) (*(volatile unsigned int *)(PCI_V3_BASE + (unsigned int)(o)) = (unsigned int)(v))
+#define _V3Read32(o)    (*(volatile unsigned int *)(PCI_V3_BASE + (unsigned int)(o)))
+
+/* Compute address necessary to access PCI config space for the given */
+/* bus and device. */
+#define PCI_CONFIG_ADDRESS( __bus, __devfn, __offset ) ({				\
+	unsigned int __address, __devicebit;						\
+	unsigned short __mapaddress;							\
+	unsigned int __dev = PCI_DEV (__devfn);	/* FIXME to check!! (slot?) */		\
+											\
+	if (__bus == 0) {								\
+		/* local bus segment so need a type 0 config cycle */			\
+		/* build the PCI configuration "address" with one-hot in A31-A11 */	\
+		__address = PCI_CONFIG_BASE;						\
+		__address |= ((__devfn & 0x07) << 8);					\
+		__address |= __offset & 0xFF;						\
+		__mapaddress = 0x000A;	/* 101=>config cycle, 0=>A1=A0=0 */		\
+		__devicebit = (1 << (__dev + 11));					\
+											\
+		if ((__devicebit & 0xFF000000) != 0) {					\
+			/* high order bits are handled by the MAP register */		\
+			__mapaddress |= (__devicebit >> 16);				\
+		} else {								\
+			/* low order bits handled directly in the address */		\
+			__address |= __devicebit;					\
+		}									\
+	} else {		/* bus !=0 */						\
+		/* not the local bus segment so need a type 1 config cycle */		\
+		/* A31-A24 are don't care (so clear to 0) */				\
+		__mapaddress = 0x000B;	/* 101=>config cycle, 1=>A1&A0 from PCI_CFG */	\
+		__address = PCI_CONFIG_BASE;						\
+		__address |= ((__bus & 0xFF) << 16);	/* bits 23..16 = bus number     */  \
+		__address |= ((__dev & 0x1F) << 11);	/* bits 15..11 = device number  */  \
+		__address |= ((__devfn & 0x07) << 8);	/* bits 10..8  = function number */ \
+		__address |= __offset & 0xFF;	/* bits  7..0  = register number */	\
+	}										\
+	_V3Write16 (V3_LB_MAP1, __mapaddress);						\
+	__address;									\
+})
+
+/* _V3OpenConfigWindow - open V3 configuration window */
+#define _V3OpenConfigWindow() {								\
+	/* Set up base0 to see all 512Mbytes of memory space (not	     */		\
+	/* prefetchable), this frees up base1 for re-use by configuration*/		\
+	/* memory */									\
+											\
+	_V3Write32 (V3_LB_BASE0, ((INTEGRATOR_PCI_BASE & 0xFFF00000) |			\
+				     0x90 | V3_LB_BASE_M_ENABLE));			\
+	/* Set up base1 to point into configuration space, note that MAP1 */		\
+	/* register is set up by pciMakeConfigAddress(). */				\
+											\
+	_V3Write32 (V3_LB_BASE1, ((CPU_PCI_CNFG_ADRS & 0xFFF00000) |			\
+				     0x40 | V3_LB_BASE_M_ENABLE));			\
+}
+
+/* _V3CloseConfigWindow - close V3 configuration window */
+#define _V3CloseConfigWindow() {							\
+    /* Reassign base1 for use by prefetchable PCI memory */				\
+	_V3Write32 (V3_LB_BASE1, (((INTEGRATOR_PCI_BASE + 0x10000000) & 0xFFF00000)	\
+					| 0x84 | V3_LB_BASE_M_ENABLE));			\
+	_V3Write16 (V3_LB_MAP1,								\
+	    (((INTEGRATOR_PCI_BASE + 0x10000000) & 0xFFF00000) >> 16) | 0x0006);	\
+											\
+	/* And shrink base0 back to a 256M window (NOTE: MAP0 already correct) */	\
+											\
+	_V3Write32 (V3_LB_BASE0, ((INTEGRATOR_PCI_BASE & 0xFFF00000) |			\
+			     0x80 | V3_LB_BASE_M_ENABLE));				\
+}
+
+static int pci_integrator_read_byte (struct pci_controller *hose, pci_dev_t dev,
+				     int offset, unsigned char *val)
+{
+	_V3OpenConfigWindow ();
+	*val = *(volatile unsigned char *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							       PCI_FUNC (dev),
+							       offset);
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_read__word (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned short *val)
+{
+	_V3OpenConfigWindow ();
+	*val = *(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+								PCI_FUNC (dev),
+								offset);
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_read_dword (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned int *val)
+{
+	_V3OpenConfigWindow ();
+	*val = *(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+								PCI_FUNC (dev),
+								offset);
+	*val |= (*(volatile unsigned int *)
+		 PCI_CONFIG_ADDRESS (PCI_BUS (dev), PCI_FUNC (dev),
+				     (offset + 2))) << 16;
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_write_byte (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned char val)
+{
+	_V3OpenConfigWindow ();
+	*(volatile unsigned char *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							PCI_FUNC (dev),
+							offset) = val;
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_write_word (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned short val)
+{
+	_V3OpenConfigWindow ();
+	*(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							 PCI_FUNC (dev),
+							 offset) = val;
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_write_dword (struct pci_controller *hose,
+				       pci_dev_t dev, int offset,
+				       unsigned int val)
+{
+	_V3OpenConfigWindow ();
+	*(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							 PCI_FUNC (dev),
+							 offset) = (val & 0xFFFF);
+	*(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							 PCI_FUNC (dev),
+							 (offset + 2)) = ((val >> 16) & 0xFFFF);
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+/******************************
+ * PCI initialisation
+ ******************************/
+
+struct pci_controller integrator_hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_integrator_config_table,
+#endif
+};
+
+void pci_init_board (void)
+{
+	volatile int i, j;
+	struct pci_controller *hose = &integrator_hose;
+
+	/* setting this register will take the V3 out of reset */
+
+	*(volatile unsigned int *) (INTEGRATOR_SC_PCIENABLE) = 1;
+
+	/* wait a few usecs to settle the device and the PCI bus */
+
+	for (i = 0; i < 100; i++)
+		j = i + 1;
+
+	/* Now write the Base I/O Address Word to V3_BASE + 0x6C */
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_IO_BASE) =
+		(unsigned short) (V3_BASE >> 16);
+
+	do {
+		*(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA) = 0xAA;
+		*(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA + 4) =
+			0x55;
+	} while (*(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA) != 0xAA
+		 || *(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA +
+						 4) != 0x55);
+
+	/* Make sure that V3 register access is not locked, if it is, unlock it */
+
+	if ((*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) &
+	     V3_SYSTEM_M_LOCK)
+	    == V3_SYSTEM_M_LOCK)
+		*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) = 0xA05F;
+
+	/* Ensure that the slave accesses from PCI are disabled while we */
+	/* setup windows */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD) &=
+		~(V3_COMMAND_M_MEM_EN | V3_COMMAND_M_IO_EN);
+
+	/* Clear RST_OUT to 0; keep the PCI bus in reset until we've finished */
+
+	*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) &=
+		~V3_SYSTEM_M_RST_OUT;
+
+	/* Make all accesses from PCI space retry until we're ready for them */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CFG) |=
+		V3_PCI_CFG_M_RETRY_EN;
+
+	/* Set up any V3 PCI Configuration Registers that we absolutely have to */
+	/* LB_CFG controls Local Bus protocol. */
+	/* Enable LocalBus byte strobes for READ accesses too. */
+	/* set bit 7 BE_IMODE and bit 6 BE_OMODE */
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_CFG) |= 0x0C0;
+
+	/* PCI_CMD controls overall PCI operation. */
+	/* Enable PCI bus master. */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD) |= 0x04;
+
+	/* PCI_MAP0 controls where the PCI to CPU memory window is on Local Bus */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_MAP0) =
+		(INTEGRATOR_BOOT_ROM_BASE) | (V3_PCI_MAP_M_ADR_SIZE_512M |
+					      V3_PCI_MAP_M_REG_EN |
+					      V3_PCI_MAP_M_ENABLE);
+
+	/* PCI_BASE0 is the PCI address of the start of the window */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_BASE0) =
+		INTEGRATOR_BOOT_ROM_BASE;
+
+	/* PCI_MAP1 is LOCAL address of the start of the window */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_MAP1) =
+		(INTEGRATOR_HDR0_SDRAM_BASE) | (V3_PCI_MAP_M_ADR_SIZE_1024M |
+						V3_PCI_MAP_M_REG_EN |
+						V3_PCI_MAP_M_ENABLE);
+
+	/* PCI_BASE1 is the PCI address of the start of the window */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_BASE1) =
+		INTEGRATOR_HDR0_SDRAM_BASE;
+
+	/* Set up the windows from local bus memory into PCI configuration, */
+	/* I/O and Memory. */
+	/* PCI I/O, LB_BASE2 and LB_MAP2 are used exclusively for this. */
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_BASE2) =
+		((CPU_PCI_IO_ADRS >> 24) << 8) | V3_LB_BASE_M_ENABLE;
+	*(volatile unsigned short *) (V3_BASE + V3_LB_MAP2) = 0;
+
+	/* PCI Configuration, use LB_BASE1/LB_MAP1. */
+
+	/* PCI Memory use LB_BASE0/LB_MAP0 and LB_BASE1/LB_MAP1 */
+	/* Map first 256Mbytes as non-prefetchable via BASE0/MAP0 */
+	/* (INTEGRATOR_PCI_BASE == PCI_MEM_BASE) */
+
+	*(volatile unsigned int *) (V3_BASE + V3_LB_BASE0) =
+		INTEGRATOR_PCI_BASE | (0x80 | V3_LB_BASE_M_ENABLE);
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_MAP0) =
+		((INTEGRATOR_PCI_BASE >> 20) << 0x4) | 0x0006;
+
+	/* Map second 256 Mbytes as prefetchable via BASE1/MAP1 */
+
+	*(volatile unsigned int *) (V3_BASE + V3_LB_BASE1) =
+		INTEGRATOR_PCI_BASE | (0x84 | V3_LB_BASE_M_ENABLE);
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_MAP1) =
+		(((INTEGRATOR_PCI_BASE + 0x10000000) >> 20) << 4) | 0x0006;
+
+	/* Allow accesses to PCI Configuration space */
+	/* and set up A1, A0 for type 1 config cycles */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CFG) =
+		((*(volatile unsigned short *) (V3_BASE + V3_PCI_CFG)) &
+		 ~(V3_PCI_CFG_M_RETRY_EN | V3_PCI_CFG_M_AD_LOW1)) |
+		V3_PCI_CFG_M_AD_LOW0;
+
+	/* now we can allow in PCI MEMORY accesses */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD) =
+		(*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD)) |
+		V3_COMMAND_M_MEM_EN;
+
+	/* Set RST_OUT to take the PCI bus is out of reset, PCI devices can */
+	/* initialise and lock the V3 system register so that no one else */
+	/* can play with it */
+
+	*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) =
+		(*(volatile unsigned short *) (V3_BASE + V3_SYSTEM)) |
+		V3_SYSTEM_M_RST_OUT;
+
+	*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) =
+		(*(volatile unsigned short *) (V3_BASE + V3_SYSTEM)) |
+		V3_SYSTEM_M_LOCK;
+
+	/*
+	 * Register the hose
+	 */
+	hose->first_busno = 0;
+	hose->last_busno = 0xff;
+
+	/* System memory space */
+	pci_set_region (hose->regions + 0,
+			0x00000000, 0x40000000, 0x01000000,
+			PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+	/* PCI Memory - config space */
+	pci_set_region (hose->regions + 1,
+			0x00000000, 0x62000000, 0x01000000, PCI_REGION_MEM);
+
+	/* PCI V3 regs */
+	pci_set_region (hose->regions + 2,
+			0x00000000, 0x61000000, 0x00080000, PCI_REGION_MEM);
+
+	/* PCI I/O space */
+	pci_set_region (hose->regions + 3,
+			0x00000000, 0x60000000, 0x00010000, PCI_REGION_IO);
+
+	pci_set_ops (hose,
+		     pci_integrator_read_byte,
+		     pci_integrator_read__word,
+		     pci_integrator_read_dword,
+		     pci_integrator_write_byte,
+		     pci_integrator_write_word, pci_integrator_write_dword);
+
+	hose->region_count = 4;
+
+	pci_register_hose (hose);
+
+	pciauto_config_init (hose);
+	pciauto_config_device (hose, 0);
+
+	hose->last_busno = pci_hose_scan (hose);
+}
+#endif
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+	  		   for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+	return 0;
+}

board/integratorap/platform.S

@@ -0,0 +1,33 @@
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2004, ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+.globl platformsetup
+platformsetup:
+
+	/* All done by Integrator's boot monitor! */
+	mov pc, lr

board/integratorap/u-boot.lds

@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+	. = ALIGN(4);
+	.text	:
+	{
+	  cpu/arm926ejs/start.o	(.text)
+	  *(.text)
+	}
+	.rodata : { *(.rodata) }
+	. = ALIGN(4);
+	.data : { *(.data) }
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/integratorcp/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= integratorcp.o flash.o
+SOBJS	:= platform.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/integratorcp/config.mk

@@ -0,0 +1,5 @@
+#
+# image should be loaded at 0x01000000
+#
+
+TEXT_BASE = 0x01000000

board/integratorcp/flash.c

@@ -0,0 +1,473 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)			__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)			__swab32(x)
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+	unsigned int sector_number;
+	unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
+	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+	int i;
+	OrgDef *pOrgDef;
+
+	pOrgDef = OrgIntel_28F256L18T;
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			if (i > 255) {
+				info->start[i] = base + (i * 0x8000);
+				info->protect[i] = 0;
+			} else {
+				info->start[i] = base +
+						(i * PHYS_FLASH_SECT_SIZE);
+				info->protect[i] = 0;
+			}
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F256L18T:
+		printf ("FLASH 28F256L18T\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);		/* no or unknown flash  */
+	}
+
+	mb ();
+	value = addr[1];	/* device ID        */
+	switch (value) {
+
+	case (FPW) (INTEL_ID_28F256L18T):
+		info->flash_id += FLASH_28F256L18T;
+		info->sector_count = 259;
+		info->size = 0x02000000;
+		break;			/* => 32 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+				info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK    0x0080
+
+	*addr = (FPW) 0x00500050;	/* clear status register */
+
+	/* this sends the clear lock bit command */
+	*addr = (FPW) 0x00600060;
+	*addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+				info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+				prot);
+	} else {
+		printf ("\n");
+	}
+
+
+	start = get_timer (0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			flash_unprotect_sectors (addr);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;/* clear status register */
+			*addr = (FPW) 0x00200020;/* erase setup */
+			*addr = (FPW) 0x00D000D0;/* erase confirm */
+
+			while (((status =
+				*addr) & (FPW) 0x00800080) !=
+				(FPW) 0x00800080) {
+					if (get_timer_masked () >
+					CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					/* suspend erase     */
+					*addr = (FPW) 0x00B000B0;
+					/* reset to read mode */
+					*addr = (FPW) 0x00FF00FF;
+					rcode = 1;
+					break;
+				}
+			}
+
+			/* clear status register cmd.   */
+			*addr = (FPW) 0x00500050;
+			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	flash_unprotect_sectors (addr);
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}

board/integratorcp/integratorcp.c

@@ -0,0 +1,111 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * (C) Copyright 2004
+ * ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+void flash__init (void);
+void ether__init (void);
+void peripheral_power_enable (void);
+
+#if defined(CONFIG_SHOW_BOOT_PROGRESS)
+void show_boot_progress(int progress)
+{
+    printf("Boot reached stage %d\n", progress);
+}
+#endif
+
+#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
+
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+		"subs %0, %1, #1\n"
+		"bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* arch number of Integrator Board */
+	gd->bd->bi_arch_number = 275;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x00000100;
+
+	gd->flags = 0;
+
+	icache_enable ();
+
+	flash__init ();
+	ether__init ();
+	return 0;
+}
+
+
+int misc_init_r (void)
+{
+	setenv("verify", "n");
+	return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+	  		   for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+	return 0;
+}

board/integratorcp/platform.S

@@ -0,0 +1,33 @@
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003, ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+.globl platformsetup
+platformsetup:
+
+	/* All done by IntegratorCP's boot monitor! */
+	mov pc, lr

board/integratorcp/u-boot.lds

@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+	. = ALIGN(4);
+	.text	:
+	{
+	  cpu/arm926ejs/start.o	(.text)
+	  *(.text)
+	}
+	.rodata : { *(.rodata) }
+	. = ALIGN(4);
+	.data : { *(.data) }
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/ispan/Makefile

@@ -0,0 +1,46 @@
+#
+# Copyright (C) 2004 Arabella Software Ltd.
+# Yuli Barcohen <yuli@arabellasw.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/ispan/config.mk

@@ -0,0 +1,29 @@
+#
+# Copyright (C) 2004 Arabella Software Ltd.
+# Yuli Barcohen <yuli@arabellasw.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Interphase iSPAN Communications Controllers
+#
+#TEXT_BASE = 0xFF800000
+#TEXT_BASE = 0xFFBA0000
+TEXT_BASE = 0xFE7A0000

board/ispan/ispan.c

@@ -0,0 +1,464 @@
+/*
+ * Copyright (C) 2004 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * Support for Interphase iSPAN Communications Controllers
+ * (453x and others). Tested on 4532.
+ *
+ * Derived from iSPAN 4539 port (iphase4539) by
+ * Wolfgang Grandegger <wg@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ioports.h>
+#include <mpc8260.h>
+#include <asm/io.h>
+
+/*
+ * I/O Ports configuration table
+ *
+ * If conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+#define CFG_FCC1 (CONFIG_ETHER_INDEX == 1)
+#define CFG_FCC2 (CONFIG_ETHER_INDEX == 2)
+#define CFG_FCC3 (CONFIG_ETHER_INDEX == 3)
+
+const iop_conf_t iop_conf_tab[4][32] = {
+    /* Port A */
+    {	/*	      conf      ppar psor pdir podr pdat */
+	/* PA31 */ { CFG_FCC1,   1,   1,   0,   0,   0 }, /* FCC1 MII COL   */
+	/* PA30 */ { CFG_FCC1,   1,   1,   0,   0,   0 }, /* FCC1 MII CRS   */
+	/* PA29 */ { CFG_FCC1,   1,   1,   1,   0,   0 }, /* FCC1 MII TX_ER */
+	/* PA28 */ { CFG_FCC1,   1,   1,   1,   0,   0 }, /* FCC1 MII TX_EN */
+	/* PA27 */ { CFG_FCC1,   1,   1,   0,   0,   0 }, /* FCC1 MII RX_DV */
+	/* PA26 */ { CFG_FCC1,   1,   1,   0,   0,   0 }, /* FCC1 MII RX_ER */
+	/* PA25 */ { 0,          0,   0,   0,   0,   0 }, /* PA25 */
+	/* PA24 */ { 0,          0,   0,   0,   0,   0 }, /* PA24 */
+	/* PA23 */ { 0,          0,   0,   0,   0,   0 }, /* PA23 */
+	/* PA22 */ { 0,          0,   0,   0,   0,   0 }, /* PA22 */
+	/* PA21 */ { CFG_FCC1,   1,   0,   1,   0,   0 }, /* FCC1 MII TxD[3] */
+	/* PA20 */ { CFG_FCC1,   1,   0,   1,   0,   0 }, /* FCC1 MII TxD[2] */
+	/* PA19 */ { CFG_FCC1,   1,   0,   1,   0,   0 }, /* FCC1 MII TxD[1] */
+	/* PA18 */ { CFG_FCC1,   1,   0,   1,   0,   0 }, /* FCC1 MII TxD[0] */
+	/* PA17 */ { CFG_FCC1,   1,   0,   0,   0,   0 }, /* FCC1 MII RxD[0] */
+	/* PA16 */ { CFG_FCC1,   1,   0,   0,   0,   0 }, /* FCC1 MII RxD[1] */
+	/* PA15 */ { CFG_FCC1,   1,   0,   0,   0,   0 }, /* FCC1 MII RxD[2] */
+	/* PA14 */ { CFG_FCC1,   1,   0,   0,   0,   0 }, /* FCC1 MII RxD[3] */
+	/* PA13 */ { 0,          0,   0,   0,   0,   0 }, /* PA13 */
+	/* PA12 */ { 0,          0,   0,   0,   0,   0 }, /* PA12 */
+	/* PA11 */ { 0,          0,   0,   0,   0,   0 }, /* PA11 */
+	/* PA10 */ { 0,          0,   0,   0,   0,   0 }, /* PA10 */
+	/* PA9  */ { 0,          1,   0,   1,   0,   0 }, /* SMC2 SMTXD */
+	/* PA8  */ { 0,          1,   0,   0,   0,   0 }, /* SMC2 SMRXD */
+	/* PA7  */ { 0,          0,   0,   0,   0,   0 }, /* PA7 */
+	/* PA6  */ { 0,          0,   0,   0,   0,   0 }, /* PA6 */
+	/* PA5  */ { 0,          0,   0,   0,   0,   0 }, /* PA5 */
+	/* PA4  */ { 0,          0,   0,   0,   0,   0 }, /* PA4 */
+	/* PA3  */ { 0,          0,   0,   0,   0,   0 }, /* PA3 */
+	/* PA2  */ { 0,          0,   0,   0,   0,   0 }, /* PA2 */
+	/* PA1  */ { 0,          0,   0,   0,   0,   0 }, /* PA1 */
+	/* PA0  */ { 0,          0,   0,   0,   0,   0 }  /* PA0 */
+    },
+
+    /* Port B */
+    {   /*	      conf      ppar psor pdir podr pdat */
+	/* PB31 */ { CFG_FCC2,   1,   0,   1,   0,   0 }, /* FCC2 MII TX_ER  */
+	/* PB30 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII RX_DV  */
+	/* PB29 */ { CFG_FCC2,   1,   1,   1,   0,   0 }, /* FCC2 MII TX_EN  */
+	/* PB28 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII RX_ER  */
+	/* PB27 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII COL    */
+	/* PB26 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII CRS    */
+	/* PB25 */ { CFG_FCC2,   1,   0,   1,   0,   0 }, /* FCC2 MII TxD[3] */
+	/* PB24 */ { CFG_FCC2,   1,   0,   1,   0,   0 }, /* FCC2 MII TxD[2] */
+	/* PB23 */ { CFG_FCC2,   1,   0,   1,   0,   0 }, /* FCC2 MII TxD[1] */
+	/* PB22 */ { CFG_FCC2,   1,   0,   1,   0,   0 }, /* FCC2 MII TxD[0] */
+	/* PB21 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII RxD[0] */
+	/* PB20 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII RxD[1] */
+	/* PB19 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII RxD[2] */
+	/* PB18 */ { CFG_FCC2,   1,   0,   0,   0,   0 }, /* FCC2 MII RxD[3] */
+	/* PB17 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII RX_DV  */
+	/* PB16 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII RX_ER  */
+	/* PB15 */ { CFG_FCC3,   1,   0,   1,   0,   0 }, /* FCC3 MII TX_ER  */
+	/* PB14 */ { CFG_FCC3,   1,   0,   1,   0,   0 }, /* FCC3 MII TX_EN  */
+	/* PB13 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII COL    */
+	/* PB12 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII CRS    */
+	/* PB11 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII RxD[3] */
+	/* PB10 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII RxD[2] */
+	/* PB9  */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII RxD[1] */
+	/* PB8  */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII RxD[0] */
+	/* PB7  */ { CFG_FCC3,   1,   0,   1,   0,   0 }, /* FCC3 MII TxD[0] */
+	/* PB6  */ { CFG_FCC3,   1,   0,   1,   0,   0 }, /* FCC3 MII TxD[1] */
+	/* PB5  */ { CFG_FCC3,   1,   0,   1,   0,   0 }, /* FCC3 MII TxD[2] */
+	/* PB4  */ { CFG_FCC3,   1,   0,   1,   0,   0 }, /* FCC3 MII TxD[3] */
+	/* PB3  */ { 0,          0,   0,   0,   0,   0 }, /* pin doesn't exist */
+	/* PB2  */ { 0,          0,   0,   0,   0,   0 }, /* pin doesn't exist */
+	/* PB1  */ { 0,          0,   0,   0,   0,   0 }, /* pin doesn't exist */
+	/* PB0  */ { 0,          0,   0,   0,   0,   0 }  /* pin doesn't exist */
+    },
+
+    /* Port C */
+    {   /*	      conf      ppar psor pdir podr pdat */
+	/* PC31 */ { 0,          0,   0,   0,   0,   0 }, /* PC31 */
+	/* PC30 */ { 0,          0,   0,   0,   0,   0 }, /* PC30 */
+	/* PC29 */ { 0,          0,   0,   0,   0,   0 }, /* PC29 */
+	/* PC28 */ { 0,          0,   0,   0,   0,   0 }, /* PC28 */
+	/* PC27 */ { 0,          0,   0,   0,   0,   0 }, /* PC27 */
+	/* PC26 */ { 0,          0,   0,   0,   0,   0 }, /* PC26 */
+	/* PC25 */ { 0,          0,   0,   0,   0,   0 }, /* PC25 */
+	/* PC24 */ { 0,          0,   0,   0,   0,   0 }, /* PC24 */
+	/* PC23 */ { 0,          0,   0,   0,   0,   0 }, /* PC23 */
+	/* PC22 */ { 0,          0,   0,   0,   0,   0 }, /* PC22 */
+	/* PC21 */ { 0,          0,   0,   0,   0,   0 }, /* PC21 */
+	/* PC20 */ { 0,          0,   0,   0,   0,   0 }, /* PC20 */
+	/* PC19 */ { 0,          0,   0,   0,   0,   0 }, /* PC19 */
+	/* PC18 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII Rx Clock (CLK14) */
+	/* PC17 */ { 0,          0,   0,   0,   0,   0 }, /* PC17 */
+	/* PC16 */ { CFG_FCC3,   1,   0,   0,   0,   0 }, /* FCC3 MII Tx Clock (CLK16) */
+	/* PC15 */ { 0,          0,   0,   0,   0,   0 }, /* PC15 */
+	/* PC14 */ { 0,          0,   0,   0,   0,   0 }, /* PC14 */
+	/* PC13 */ { 0,          0,   0,   0,   0,   0 }, /* PC13 */
+	/* PC12 */ { 0,          0,   0,   0,   0,   0 }, /* PC12 */
+	/* PC11 */ { 0,          0,   0,   0,   0,   0 }, /* PC11 */
+	/* PC10 */ { 0,          0,   0,   0,   0,   0 }, /* PC10 */
+	/* PC9  */ { 0,          0,   0,   0,   0,   0 }, /* PC9  */
+	/* PC8  */ { 0,          0,   0,   0,   0,   0 }, /* PC8  */
+	/* PC7  */ { 0,          0,   0,   0,   0,   0 }, /* PC7  */
+	/* PC6  */ { 0,          0,   0,   0,   0,   0 }, /* PC6  */
+	/* PC5  */ { 0,          0,   0,   0,   0,   0 }, /* PC5  */
+	/* PC4  */ { 0,          0,   0,   0,   0,   0 }, /* PC4  */
+	/* PC3  */ { 0,          0,   0,   0,   0,   0 }, /* PC3  */
+	/* PC2  */ { 0,          0,   0,   0,   0,   0 }, /* PC2  */
+	/* PC1  */ { 0,          0,   0,   0,   0,   0 }, /* PC1  */
+	/* PC0  */ { 0,          0,   0,   0,   0,   0 }  /* PC0  */
+    },
+
+    /* Port D */
+    {   /*	      conf      ppar psor pdir podr pdat */
+	/* PD31 */ { 0,          0,   0,   0,   0,   0 }, /* PD31 */
+	/* PD30 */ { 0,          0,   0,   0,   0,   0 }, /* PD30 */
+	/* PD29 */ { 0,          0,   0,   0,   0,   0 }, /* PD29 */
+	/* PD28 */ { 0,          0,   0,   0,   0,   0 }, /* PD28 */
+	/* PD27 */ { 0,          0,   0,   0,   0,   0 }, /* PD27 */
+	/* PD26 */ { 0,          0,   0,   0,   0,   0 }, /* PD26 */
+	/* PD25 */ { 0,          0,   0,   0,   0,   0 }, /* PD25 */
+	/* PD24 */ { 0,          0,   0,   0,   0,   0 }, /* PD24 */
+	/* PD23 */ { 0,          0,   0,   0,   0,   0 }, /* PD23 */
+	/* PD22 */ { 0,          0,   0,   0,   0,   0 }, /* PD22 */
+	/* PD21 */ { 0,          0,   0,   0,   0,   0 }, /* PD21 */
+	/* PD20 */ { 0,          0,   0,   0,   0,   0 }, /* PD20 */
+	/* PD19 */ { 0,          0,   0,   0,   0,   0 }, /* PD19 */
+	/* PD18 */ { 0,          1,   1,   0,   0,   0 }, /* SPICLK  */
+	/* PD17 */ { 0,          1,   1,   0,   0,   0 }, /* SPIMOSI */
+	/* PD16 */ { 0,          1,   1,   0,   0,   0 }, /* SPIMISO */
+	/* PD15 */ { 0,          1,   1,   0,   1,   0 }, /* I2C SDA */
+	/* PD14 */ { 0,          1,   1,   0,   1,   0 }, /* I2C SCL */
+	/* PD13 */ { 1,          0,   0,   0,   0,   0 }, /* MII MDIO */
+	/* PD12 */ { 1,          0,   0,   1,   0,   0 }, /* MII MDC  */
+	/* PD11 */ { 0,          0,   0,   0,   0,   0 }, /* PD11 */
+	/* PD10 */ { 0,          0,   0,   0,   0,   0 }, /* PD10 */
+	/* PD9  */ { 1,          1,   0,   1,   0,   0 }, /* SMC1 SMTXD */
+	/* PD8  */ { 1,          1,   0,   0,   0,   0 }, /* SMC1 SMRXD */
+	/* PD7  */ { 0,          0,   0,   0,   0,   0 }, /* PD7 */
+	/* PD6  */ { CFG_FCC3,   0,   0,   1,   0,   1 }, /* MII PHY Reset  */
+	/* PD5  */ { CFG_FCC3,   0,   0,   1,   0,   0 }, /* MII PHY Enable */
+	/* PD4  */ { 0,          0,   0,   0,   0,   0 }, /* PD4 */
+	/* PD3  */ { 0,          0,   0,   0,   0,   0 }, /* pin doesn't exist */
+	/* PD2  */ { 0,          0,   0,   0,   0,   0 }, /* pin doesn't exist */
+	/* PD1  */ { 0,          0,   0,   0,   0,   0 }, /* pin doesn't exist */
+	/* PD0  */ { 0,          0,   0,   0,   0,   0 }  /* pin doesn't exist */
+    }
+};
+
+#define PSPAN_ADDR      0xF0020000
+#define EEPROM_REG      0x408
+#define EEPROM_READ_CMD 0xA000
+#define PSPAN_WRITE(a,v) \
+    *((volatile unsigned long *)(PSPAN_ADDR+(a))) = v; eieio()
+#define PSPAN_READ(a) \
+    *((volatile unsigned long *)(PSPAN_ADDR+(a)))
+
+static int seeprom_read (int addr, uchar * data, int size)
+{
+	ulong val, cmd;
+	int i;
+
+	for (i = 0; i < size; i++) {
+
+		cmd = EEPROM_READ_CMD;
+		cmd |= ((addr + i) << 24) & 0xff000000;
+
+		/* Wait for ACT to authorize write */
+		while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
+			eieio ();
+
+		/* Write command */
+		PSPAN_WRITE (EEPROM_REG, cmd);
+
+		/* Wait for data to be valid */
+		while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
+			eieio ();
+		/* Do it twice, first read might be erratic */
+		while ((val = PSPAN_READ (EEPROM_REG)) & 0x80)
+			eieio ();
+
+		/* Read error */
+		if (val & 0x00000040) {
+			return -1;
+		} else {
+			data[i] = (val >> 16) & 0xff;
+		}
+	}
+	return 0;
+}
+
+/***************************************************************
+ * We take some basic Hardware Configuration Parameter from the
+ * Serial EEPROM conected to the PSpan bridge. We keep it as
+ * simple as possible.
+ */
+#ifdef DEBUG
+static int hwc_flash_size (void)
+{
+	uchar byte;
+
+	if (!seeprom_read (0x40, &byte, sizeof (byte))) {
+		switch ((byte >> 2) & 0x3) {
+		case 0x1:
+			return 0x0400000;
+			break;
+		case 0x2:
+			return 0x0800000;
+			break;
+		case 0x3:
+			return 0x1000000;
+		default:
+			return 0x0100000;
+		}
+	}
+	return -1;
+}
+
+static int hwc_local_sdram_size (void)
+{
+	uchar byte;
+
+	if (!seeprom_read (0x40, &byte, sizeof (byte))) {
+		switch ((byte & 0x03)) {
+		case 0x1:
+			return 0x0800000;
+		case 0x2:
+			return 0x1000000;
+		default:
+			return 0;			/* not present */
+		}
+	}
+	return -1;
+}
+#endif	/* DEBUG */
+
+static int hwc_main_sdram_size (void)
+{
+	uchar byte;
+
+	if (!seeprom_read (0x41, &byte, sizeof (byte))) {
+		return 0x1000000 << ((byte >> 5) & 0x7);
+	}
+	return -1;
+}
+
+static int hwc_serial_number (void)
+{
+	int sn = -1;
+
+	if (!seeprom_read (0xa0, (char *) &sn, sizeof (sn))) {
+		sn = cpu_to_le32 (sn);
+	}
+	return sn;
+}
+
+static int hwc_mac_address (char *str)
+{
+	char mac[6];
+
+	if (!seeprom_read (0xb0, mac, sizeof (mac))) {
+		sprintf (str, "%02X:%02X:%02X:%02X:%02X:%02X",
+				 mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
+	} else {
+		strcpy (str, "ERROR");
+		return -1;
+	}
+	return 0;
+}
+
+static int hwc_manufact_date (char *str)
+{
+	uchar byte;
+	int value;
+
+	if (seeprom_read (0x92, &byte, sizeof (byte)))
+		goto out;
+	value = byte;
+	if (seeprom_read (0x93, &byte, sizeof (byte)))
+		goto out;
+	value += byte << 8;
+	sprintf (str, "%02d/%02d/%04d",
+			 value & 0x1F, (value >> 5) & 0xF,
+			 1980 + ((value >> 9) & 0x1FF));
+	return 0;
+
+out:
+	strcpy (str, "ERROR");
+	return -1;
+}
+
+static int hwc_board_type (char **str)
+{
+	ushort id = 0;
+
+	if (seeprom_read (7, (uchar *) & id, sizeof (id)) == 0) {
+		switch (id) {
+		case 0x9080:
+			*str = "4532-002";
+			break;
+		case 0x9081:
+			*str = "4532-001";
+			break;
+		case 0x9082:
+			*str = "4532-000";
+			break;
+		default:
+			*str = "Unknown";
+		}
+	} else {
+		*str = "Unknown";
+	}
+
+	return id;
+}
+
+long int initdram (int board_type)
+{
+	long maxsize = hwc_main_sdram_size();
+
+#if !defined(CFG_RAMBOOT) && !defined(CFG_USE_FIRMWARE)
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8260_t *memctl = &immap->im_memctl;
+	volatile uchar *base;
+	int i;
+
+	immap->im_siu_conf.sc_ppc_acr  = 0x00000026;
+	immap->im_siu_conf.sc_ppc_alrh = 0x01276345;
+	immap->im_siu_conf.sc_ppc_alrl = 0x89ABCDEF;
+	immap->im_siu_conf.sc_lcl_acr  = 0x00000000;
+	immap->im_siu_conf.sc_lcl_alrh = 0x01234567;
+	immap->im_siu_conf.sc_lcl_alrl = 0x89ABCDEF;
+	immap->im_siu_conf.sc_tescr1   = 0x00004000;
+	immap->im_siu_conf.sc_ltescr1  = 0x00004000;
+
+	memctl->memc_mptpr = CFG_MPTPR;
+
+	/* Initialise 60x bus SDRAM */
+	base = (uchar *)(CFG_SDRAM_BASE | 0x110);
+	memctl->memc_psrt  = CFG_PSRT;
+	memctl->memc_or1   = CFG_60x_OR;
+	memctl->memc_br1   = CFG_SDRAM_BASE | CFG_60x_BR;
+
+	memctl->memc_psdmr = CFG_PSDMR | 0x28000000;
+	*base = 0xFF;
+	memctl->memc_psdmr = CFG_PSDMR | 0x08000000;
+	for (i = 0; i < 8; i++)
+		*base = 0xFF;
+	memctl->memc_psdmr = CFG_PSDMR | 0x18000000;
+	*base = 0xFF;
+	memctl->memc_psdmr = CFG_PSDMR | 0x40000000;
+
+	/* Initialise local bus SDRAM */
+	base = (uchar *)CFG_LSDRAM_BASE;
+	memctl->memc_lsrt  = CFG_LSRT;
+	memctl->memc_or2   = CFG_LOC_OR;
+	memctl->memc_br2   = CFG_LSDRAM_BASE | CFG_LOC_BR;
+
+	memctl->memc_lsdmr = CFG_LSDMR | 0x28000000;
+	*base = 0xFF;
+	memctl->memc_lsdmr = CFG_LSDMR | 0x08000000;
+	for (i = 0; i < 8; i++)
+		*base = 0xFF;
+	memctl->memc_lsdmr = CFG_LSDMR | 0x18000000;
+	*base = 0xFF;
+	memctl->memc_lsdmr = CFG_LSDMR | 0x40000000;
+
+	/* We must be able to test a location outsize the maximum legal size
+	 * to find out THAT we are outside; but this address still has to be
+	 * mapped by the controller. That means, that the initial mapping has
+	 * to be (at least) twice as large as the maximum expected size.
+	 */
+	maxsize = (~(memctl->memc_or1 & BRx_BA_MSK) + 1) / 2;
+
+	maxsize = get_ram_size((long *)(memctl->memc_br1 & BRx_BA_MSK), maxsize);
+
+	memctl->memc_or1 |= ~(maxsize - 1);
+
+	if (maxsize != hwc_main_sdram_size())
+		puts("Oops: memory test has not found all memory!\n");
+#endif /* !CFG_RAMBOOT && !CFG_USE_FIRMWARE */
+
+	/* Return total RAM size (size of 60x SDRAM) */
+	return maxsize;
+}
+
+int checkboard(void)
+{
+	char string[32], *id;
+
+	hwc_manufact_date(string);
+	hwc_board_type(&id);
+	printf("Board: Interphase iSPAN %s (#%d %s)\n",
+	       id, hwc_serial_number(), string);
+#ifdef DEBUG
+	printf("Manufacturing date: %s\n", string);
+	printf("Serial number     : %d\n", hwc_serial_number());
+	printf("FLASH size        : %d MB\n", hwc_flash_size() >> 20);
+	printf("Main SDRAM size   : %d MB\n", hwc_main_sdram_size() >> 20);
+	printf("Local SDRAM size  : %d MB\n", hwc_local_sdram_size() >> 20);
+	hwc_mac_address(string);
+	printf("MAC address       : %s\n", string);
+#endif
+	return 0;
+}
+
+int misc_init_r(void)
+{
+	char *s, str[32];
+	int num;
+
+	if ((s = getenv("serial#")) == NULL &&
+	    (num = hwc_serial_number()) != -1) {
+		sprintf(str, "%06d", num);
+		setenv("serial#", str);
+	}
+	if ((s = getenv("ethaddr")) == NULL && hwc_mac_address(str) == 0) {
+		setenv("ethaddr", str);
+	}
+
+	return 0;
+}

board/ispan/u-boot.lds

@@ -0,0 +1,122 @@
+/*
+ * (C) Copyright 2001-2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Modified by Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc8260/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
+ENTRY(_start)

board/jse/Makefile

@@ -0,0 +1,44 @@
+#
+# Copyright 2004 Picture Elements, Inc.
+# Stephen Williams <steve@icarus.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o sdram.o flash.o host_bridge.o
+SOBJS	= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/jse/README.txt

@@ -0,0 +1,48 @@
+JSE Configuration Details
+
+Memory Bank 0 -- Flash chip
+---------------------------
+
+0xfff00000 - 0xffffffff
+
+The flash chip is really only 512Kbytes, but the high address bit of
+the 1Meg region is ignored, so the flash is replicated through the
+region. Thus, this is consistent with a flash base address 0xfff80000.
+
+The placement at the end is to be consistent with reset behavior,
+where the processor itself initially uses this bus to load the branch
+vector and start running.
+
+On-Chip Memory
+--------------
+
+0xf4000000 - 0xf4000fff
+
+The 405GPr includes a 4K on-chip memory that can be placed however
+software chooses. I choose to place the memory at this address, to
+keep it out of the cachable areas.
+
+
+Memory Bank 1 -- SystemACE Controller
+-------------------------------------
+
+0xf0000000 - 0xf00fffff
+
+The SystemACE chip is along on peripheral bank CS#1. We don't need
+much space, but 1Meg is the smallest we can configure the chip to
+allocate. We need it far away from the flash region, because this
+region is set to be non-cached.
+
+
+Internal Peripherals
+--------------------
+
+0xef600300 - 0xef6008ff
+
+These are scattered various peripherals internal to the PPC405GPr
+chip.
+
+SDRAM
+-----
+
+0x00000000 - 0x07ffffff  (128 MBytes)