GPIO4_21 is the LAN8720 power pin, not the LAN8720 reset pin.
Fix that, so that we can have Ethernet functional again.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The stm_is_locked_sr() function is picked from Linux kernel. For reason
unknown, the 64bit data types used by the function and present in Linux
were replaced with 32bit unsigned ones, which causes trouble.
The testcase performed was done using ST M25P80 chip.
The command used was:
=> sf protect unlock 0 0x10000
The call chain starts in stm_unlock(), which calls stm_is_locked_sr()
with negative ofs argument. This works fine in Linux, where the "ofs"
is loff_t, which is signed long long, while this fails in U-Boot, where
"ofs" is u32 (unsigned int). Because of this signedness problem, the
expression past the return statement to be incorrectly evaluated to 1,
which in turn propagates back to stm_unlock() and results in -EINVAL.
The correction is very simple, just use the correctly sized data types
with correct signedness in the function to make it work as intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
TI QSPI driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.
This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Enable CONFIG_USB_ETHER_RTL8152 support for Odroid XU4 which
has support for RTL8153-CG gigabit Ethernet adapter,
connected over USB 3.0.
commit 9dc8ba19c5 added support
for Realtek 8152/8153 driver.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The DMC driver in v3.14 kernel[0] get the ddr setting from PMU_SYS_REG2,
and it expects uboot to store the value using a same protocol. But now
the ddr setting value is different with DMC, so if you enable the DMC,
system would crash in kernel. Correct the sdram setting here, according
to the requirements of kernel.
[0]
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/
chromeos-3.14/drivers/clk/rockchip/clk-rk3288-dmc.c
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
on v2016.03-rc3, size of SPL image compiled by gcc 5.3.0 is too large for
Firefly-RK3288. (it's fine for Rock2)
$ gcc --version
gcc (Ubuntu/Linaro 5.3.0-3ubuntu1~14.04) 5.3.0 20151204
Copyright (C) 2015 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin u-boot-spl-dtb.img
Warning: SPL image is too large (size 0x80d0) and will not boot
to reduce size of SPL image, this patch makes configure_emmc() empty for
Firefly-RK3288 as same as Rock2.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
emac may use dpll as clock parent, and it request the clock frequency
multiples of 50, so change ddr frequency to 400M.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
MIPS EL boards should define CONFIG_USE_PRIVATE_LIBGCC=y to work
with EB-only toolchains like the one from kernel.org. If one do
not globally set CONFIG_USE_PRIVATE_LIBGCC=y, the build fails with:
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o)
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o)
/work/git-trees/u-boot-mips/Makefile:1171: recipe for target 'u-boot' failed
One example for a failing build is Travis CI.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Purna Chandra Mandal <purna.mandal@microchip.com>
The "R" constraint supplies the address of an variable in a register. Use
"r" instead and adjust asm to supply the content of addr in a register
instead.
Fixes: 2b8bcc5a ("MIPS: avoid .set ISA for cache operations")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Following the previous patch, malloc() is never called before gd is set,
so we can remove the special-case check for this condition.
This reverts commit 854d2b9753 "dlmalloc: ensure gd is set for early
alloc".
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When running sandbox, the following phases occur, each with different
malloc implementations or behaviors:
1) Dynamic linker execution, using the dynamic linker's own malloc()
implementation. This is fully functional.
2) After U-Boot's malloc symbol has been hooked into the GOT, but before
any U-Boot code has run. This phase is entirely non-functional, since
U-Boot's gd symbol is NULL and U-Boot's initf_malloc() and
mem_malloc_init() have not been called.
At least on Ubuntu Xenial, the dynamic linker does make both malloc() and
free() calls during this phase. Currently these free() calls crash since
they dereference gd, which is NULL.
U-Boot itself makes no use of malloc() during this phase.
3) U-Boot execution after gd is set and initf_malloc() has been called.
This is fully functional, albeit via a very simple malloc()
implementation.
4) U-Boot execution after mem_malloc_init() has been called. This is fully
functional with a complete malloc() implementation.
Furthermore, if code that called malloc() during phase 1 calls free() in
phase 3 or later, it is likely that heap corruption will occur, since
U-Boot's malloc implementation will assume the pointer is part of its own
heap, although it isn't. I have not actively observed this happening.
To prevent phase 2 from happening, this patch makes all of U-Boot's malloc
library public symbols have hidden visibility. This prevents them from
being hooked into the GOT, so only code in the U-Boot binary itself
actually calls them; any other code will call into the standard C library
malloc(). This also avoids the "furthermore" issue mentioned above.
I have seen references to this GCC pragma in blog posts from 2008, and
RHEL5's ancient gcc appears to accept it fine, so I believe it's quite
safe to use it without checking gcc version.
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- The macro __BIGGEST_ALIGNMENT__ is gcc-specific. If it is not defined
we'll just assume 16. This is correct for at least the common cases
and LLVM does not provide an equivalent macro.
- When linking U-Boot we're passing -T to the linker, and while gcc will
just pass this along with LLVM we need to be specific.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we fall back to the FS code path when we don't find u-boot
at the raw sector offset, there is no good reason to not default to
raw boot.
With this patch, I can successfully boot u-boot from a raw sector
offset on beagle-xm.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch makes the U-Boot api export its structure address as an environment
variable, so it can be used to directly hint FreeBSD's loader of api's location.
The relevant FreeBSD loader change is currently under review at:
https://reviews.freebsd.org/D5492
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Select 8-bit BCH ecc-scheme with s/w based error correction
- OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function should just return for unknown SoCs rather than writing
unexpected values to registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long, so rename it
into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
[ ported from Linux commit bac7f4c1bf5e7c6ccd5bb71edc015b26c77f7460 ]
Fixes: 5dc626f836 ("pinctrl: uniphier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary overcurrent
error which would then disable the host port.
The overcurrent condition was happening on the SoCFPGA Cyclone5 devkit, thus
USB was not working on the devkit. This patch fixes that problem.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Fix the BOOTCFG value for eMMC in the same way as commit
214c3f0f99
[imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failure]
did for sabresd.
Signed-off-by: Soeren Moch <smoch@web.de>
Move to booting a zImage kernel by default to align with the other
i.MX boards.
While at it, adjust the fdt_addr so that we can boot a standard
mainline kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
During very early boot-ROM execution the pinmux
configuration isi in Hi-Z state. If pull-up is enabled
on GPIO pad's there will be a short period of toggle
from high to low on the IO when GPIO is set low during
boot. To avoid this glitch, disable pull-up configuration
in GPIO pinmux.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
In case when usb_composite_register() failed once (for whatever reason),
it will fail further even if all conditions are correct. Example:
=> fastboot 2
Invalid Controller Index
couldn't find an available UDC
g_dnl_register: failed!, error: -19
exit not allowed from main input shell.
=> fastboot 0
g_dnl_register: failed!, error: -22
exit not allowed from main input shell.
Despite that 0 is correct index for USB controller, "fastboot 0" command
will fail, because "composite" structure wasn't cleared properly on
previous fail (on "fastboot 2" command).
This patch fixes that erroneous behavior, allowing us to use composite
even after previous failure.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a number of AMCC platforms which are close to, or with some
toolchains exceeding, the size constraints. Disable CONFIG_SYS_LONGHELP
to get us room to build with again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Copy these from Linux v4.5-rc6 tag.
This is needed so that we can keep up with newer gcc versions. Note
that we don't have the uapi/ hierarchy from the kernel so continue to
use <linux/types.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
The UniPhier SoC family has not supported ARMv8 yet, but these would
cause warnings if they were compiled with a 64bit compiler. Before
adding the ARMv8 support really, fix them now.
Because UniPhier SoCs do not support Large Physical Address Extension,
casting "phys_addr_t" into "unsigned long" would carry the address
as is.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Before adding ARMv8 support, this commit refactors the directory
structure. Move ARMv7 specific files to arch/arm/mach-uniphier/arm32
to avoid a mess by mixture of ARMv7 and ARMv8 code. Also move the
"select CPU_V7" to the lower-level menu because we will have to
select ARM64 instead of CPU_V7 for ARMv8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit d9a3bec682.
While this is a correct change to do long term it unfortunately breaks a
number of platforms that are using pdata and not named struct members so
they are getting all of their data after 'base' incorrect.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to the company's awful projecting, PH1-LD10 and PH1-sLD11 have
been renamed to PH1-LD20 and PH1-LD11, respectively.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The chains of "depends on <SoC_name>" in the current Kconfig is
clumsy. The idea here is to allow users to choose a SoC group first
(SoC group consists of some SoCs that can coexist in one binary).
Then, allow to enable/disable each SoC support in the selected SoC
group. This makes the Kconfig menu clearer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These macros are no longer used. These base addresses are
SoC-dependent, so they should not be placed in the header.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, DRAM size is converted twice:
size in byte -> size in Gbit -> enum
Optimize the code by converting the "size in byte" into enum directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now this code can be re-written with a "for" statement instead of
calling the same function multiple times.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now this code can be re-written with a "for" statement instead of
calling the same function multiple times.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now this code can be re-written with a "for" statement instead of
calling the same function multiple times.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The if-else statements for the frequency-dependent register settings
seem clumsy. Moving them to arrays would make it cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR PHY settings no longer depend on the DRAM size. Drop the
argument from the init function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now these three are almost the same. The only difference is the DTPR1
register dependency on the DRAM size, but it can be ignored. (It has
already been ignored in PH1-sLD8 and PH1-Pro4.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a field to distinguish DDR3+ from (standard) DDR3. It also
allows to delete CONFIG_DDR_STANDARD (this is not a software
configuration, but a board attribute).
Default DDR3 spec for each SoC:
PH1-LD4, PH1-sLD8: DDR3+
Others: DDR3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These settings control the clocks around the memory controller.
The debug ability is unneeded once it works properly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These settings were used only for the PH1-sLD3 and older SoCs. The
PH1-LD4 and newer one just ignore them because their DDR-PHY take
care of such timing parameters instead.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, a dummy value is defined for the UMC_SPCCTLA register
when the DRAM size is zero. This seems weird because the controller
does not need setting in the first place if the size is zero.
Also, redefine enum dram_size to represent the DRAM size per 16-bit
unit. This makes things simpler because the channel 0 and 1 are
connected with 32-bit width DRAM, while the channel 2 is connected
with 16-bit width one.
I am renaming SIZE_* into DRAM_SZ_* (and also FREQ_* to DRAM_FREQ_*
for consistency) while I am here because SIZE_* might be easily
mixed-up with the macros in include/linux/sizes.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now this code can be re-written with a "for" statement instead of
calling the same function multiple times.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit reworks "struct uniphier_board_data" with an array of
DRAM channel data in it. It will allow further cleanups by means of
"for" statements that iterate over the DDR channels.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Of the several boot devices supported, it looks like the eMMC is the
most commonly used. Enable CONFIG_ENV_IS_IN_MMC by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM expects the boot image (SPL) in the Boot Partition 1.
So, updating images involves the hardware partition switch. It might
be a bit advanced for some users.
To be user-friendly, this commit adds a useful command to update the
images; just put SPL and U-Boot proper into the public directory of
the TFTP server and execute "run emmcupdate" from the command line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier SoC family supports both (e)MMC boot and SD card boot;
however, both of them are handled in the same uclass.
When booting from the eMMC, we want to know the device number
of the (e)MMC, not SD. This command is useful to find the first
MMC (non-SD) device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Export device nodes needed for eMMC boot (eMMC node, pinctrl, and
clock) to the SPL DTB. CONFIG_SUPPORT_EMMC_BOOT is also necessary
to use "mmc partconf" command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the driver in all UniPhier defconfig files and add some
needed defines to the common files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I implemented a GPIO driver based on Driver Model for the UniPhier
SoC family, but I could not find any good reason why such SoC
specific GPIO headers are needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is currently one config option (CONFIG_NET_RETRY_COUNT) that
is available to tune the retries of the network stack.
Unfortunately, it is global to all protocols, and the value is
interpreted differently in all of them.
Add a new environment variable that directly sets the retry period for
BOOTP timeouts. If this new value is not set, the period is still derived
from the default number of retries, or from CONFIG_NET_RETRY_COUNT if
defined. When both the new variable is set and CONFIG_NET_RETRY_COUNT
is defined, the variable has precedence.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
In commit <a058052c358c> [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Bit 12(AUTO_NEGOTIATION)
is cleared too. It causes auto-negotiation timeout error on Atheros's
PHY AR8033.
To fix this problem, genphy_config_aneg() and genphy_restart_aneg()
needs to be called in ar8035_config() to enable and restart
auto-negotiation.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The patch that enabled eSDHC peripheral clock support had an
obvious error as below. This patch is used to fix it.
+#define define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
Fixes: 3285e6cbcc ("powerpc/t2080qds: enable eSDHC peripheral clock support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fix the following warning on aarch64 introduced by using p2v/v2p
functions in the code:
In file included from ./arch/arm/include/asm/byteorder.h:29:0,
from include/compiler.h:125,
from include/image.h:19,
from include/common.h:88,
from drivers/usb/host/ehci-hcd.c:10:
drivers/usb/host/ehci-hcd.c: In function ‘ehci_td_buffer’:
drivers/usb/host/ehci-hcd.c:250:49: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
^
include/linux/byteorder/little_endian.h:34:51: note: in definition of macro ‘__cpu_to_le32’
#define __cpu_to_le32(x) ((__force __le32)(__u32)(x))
^
drivers/usb/host/ehci-hcd.c:250:24: note: in expansion of macro ‘cpu_to_hc32’
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
Fix the following compiler warnings when DEBUG is on.
warning: 'bar_res' may be used uninitialized in this function.
drivers/pci/pci_auto.c:101:21:
if (!enum_only && pciauto_region_allocate(bar_res, bar_size,
^
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When an error number is provided we should use it, not change it. This fixes
the SPI and SPI flash tests.
One of these is long-standing. The other seems to have been introduced by
commit 1e90d9fd (sf: Move read_id code to sf_ops).
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 1e90d9fd (sf: Move read_id code to sf_ops)
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
We must not free data that is managed by driver mode. Remove this line,
which is a hangover from the pre-driver-model code.
This fixes a problem where 'sf probe' crashes U-Boot if the backing file
for the SPI flash cannot be found.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When using the early timer, we need to manually trigger setting up the
real timer. This will not happen automatically. Do this immediately after
starting driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In some cases the timer must be accessible before driver model is active.
Examples include when using CONFIG_TRACE to trace U-Boot's execution before
driver model is set up. Enable this option to use an early timer. These
functions must be supported by your timer driver: timer_early_get_count()
and timer_early_get_rate().
Signed-off-by: Simon Glass <sjg@chromium.org>
A few of the functions in the timer uclass are not marked with 'notrace'. Fix
this so that tracing can be used with CONFIG_TRACE.
Signed-off-by: Simon Glass <sjg@chromium.org>
The awk tool can be confused by return character (ASCII 13) in its input
since it thinks there is a separate field. These can appear if the terminal
is in raw mode, perhaps due to a previous U-Boot crash with sandbox. This
is very confusing. Remove these so that the trace test passes.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be called from the timer code on instrumented functions.
Mark it as 'notrace' so that it doesn't cause infinite recursion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With min() we must use the same type for each parameter. Fix two problems
in trace.c which produce compiler warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When used with a device tree, sandbox now requires a 'reset' controller. Add
this to the device trees so that reset works and the tests can complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 5010d98f (sandbox: Use the reset driver to handle reset)
This reverts commit 84ca65aa4b.
On signature verification failures fit_image_verify() should NOT exit with
error. Only keys marked 'required' can cause image verification failure.
This logic is already there and works correctly.
Add a comment to make this clear.
Fixes: 84ca65aa (image-fit: Fix signature checking)
Signed-off-by: Simon Glass <sjg@chromium.org>
A recent change broke the 'bootm' command on sandbox. The root cause is
using a pointer as an address. Conversion from pointer to address needs to
use map_to_sysmem() so that sandbox can do the right thing. The problem was
pre-existing but uncovered by a recent commit.
Fix this. Also move fit_get_end() to the C file to avoid needing to include
mapmem.h (and thus asm/io.h) everywhere.
Fixes: 1fec3c5d (common/image.c: Make boot_get_ramdisk() perform a check for Android images)
Signed-off-by: Simon Glass <sjg@chromium.org>
test_hush_if_test.py executes commands that require large values of
CONFIG_SYS_MAXARGS. Detect cases where the configured value is too low
and skip those tests.
Ideally, this would be implemented inside console.run_command(). However,
the command passed to that function is already a completely formed string,
and determining its argument count usage would require splitting commands
at ;, handling quoting to deal with arguments containing spaces, etc. Even
passing the command as a list wouldn't solve all these issues, since we'd
still need to split commands on ; and deal with cases like "if test ..."
which consumes 0 of the argument count.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
Sending CTRL-C to QEMU's stdin aborts the process, even if stdin is being
used as a serial port (at least in the raspi2 machine with "qemu -serial
stdin"). Avoid sending CTRL-C to U-Boot to prevent it exiting.
I'd originally used CTRL-C to make sure that if the character used to
abort autoboot ended up being treated as part of a command as well, it'd
abort command entry and return the prompt to a known state. However, this
is not needed, since aborting the autoboot eats the character used to do
that.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
This allows all the hush tests implemented in test/py to pass, under qemu
at least.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabling this driver requires some DT changes.
Adding DCC to root or main bus:
dcc: dcc {
compatible = "arm,dcc";
u-boot,dm-pre-reloc;
};
Extend alias list to link DCC:
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
Change stdout-path to point to dcc port.
stdout-path = "serial2:115200n8";
Also add support for debug uart to help with early debug.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide user option to skip SPL signature verification for cases where
u-boot is build with SPL support but full U-Boot is also verified
without SPL.
If you want to support this feature please add env__spl_skipped = True
to your boardenv configuration file.
For example Xilinx Zynq is using this feature where the same U-Boot
binary is checked with SPL and without SPL(with FSBL).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A patman series with a 'Series-notes' section causes
buildman to crash with:
self.series.notes += self.section
TypeError: cannot concatenate 'str' and 'list' objects
Fix by initializing series.notes as a one-element array
rather than a scalar.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
These two properties are necessary for SPL to get clocks from DT.
Note:
For now, only clock look-up by index is supported (clk_get_by_index()
function), so "clock-names" is never parsed in U-Boot. However, we
may want to support something like clk_get_by_name() in the future,
so let's keep "clock-names" as well as "clocks".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
fdtgrep requires /chosen node to be specified or at least more nodes which
stays in DTS to generate output.
Error message:
./tools/fdtgrep -b u-boot,dm-pre-reloc -RT dts/dt.dtb -n /chosen -O
dtb | ./tools/fdtgrep -r -O dtb - -o spl/u-boot-spl.dtb -P pinctrl-0 -P
pinctrl-names -P clocks -P clock-names -P interrupt-parent
Error: FDT_ERR_BADMAGIC
This patch add empty chosen node to keep fdtgrep happy and pass
compilation for in tree DTS file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Scrolling the simple framebuffer is really slow in Raspberry Pi to the
point it delays the boot by a second or two and makes longer output
inconvenient to follow (printenv, md).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Gets propagated into the device tree and then into /proc/cpuinfo where
users often expect it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Fix spelling errors in the "booti" help text and bring it more
in line with the bootm/bootz help texts.
Signed-off-by: Karsten Merker <merker@debian.org>
Since commit 87da2690ab
"openrisc: updating build tools naming convention", openrisc
kernel.org toolchain is out of date and cannot build U-Boot.
Update buildman and moveconfig tools to refer to the new one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Commit 755324 (configs: Use config_distro_defaults.h in ti_armv7_common.h)
made ti_armv7_common.h include config_distro_defaults.h. This breaks the
bootdelay feature in cm_t43 because now the
- #include ti_armv7_common.h (#define CONFIG_BOOTDELAY 1)
- #undef CONFIG_BOOTDELAY
- #include config_distro_defaults.h (#define CONFIG_BOOTDELAY 2)
dance in cm_t43.h is no longer valid and in fact leads to CONFIG_BOOTDELAY
not being defined.
Adapt the config file to the new inclusion hierarchy.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators
are not updated. This is not a problem in cold boot since the default values
that the pmic outputs are correct, but if Linux were to switch the module to a
low power OPP, the new voltage values will be retained after a reboot and the
module will likely hang once U-Boot raises the CPU frequency back up.
Set both CORE and MPU regulators to to 1.1V on boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the following functions:
tps65218_reg_read() for accessing redisters
tps65218_toggle_fseal() for toggling the fseal bit
tps65218_lock_fsea() for locking the fseal bit to 1
Add the following defines:
All status register bits
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
bur_am335x_common.h today holds all common configuration which is shared
over all B&R boards.
In future we want to bring up boards which are not based on AM335x only
but we still want to have common configuration over all B&R boards
independent from their architecture.
To prepare this we introduce a new file "bur_cfg_common.h", where we
move all common things, which are not architecture specific, from
bur_am335x_common.h.
On B&R am335x boards we include from now:
#include <configs/bur_cfg_common.h>
#include <configs/bur_am335x_common.h>
On other B&R boards, we include only
#include <configs/bur_cfg_common.h>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
We drop everything possible things from board headerfiles and replace
this functionality with responsible settings in Kconfig (_defconfig).
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no need to have some specific prompt, so we drop this within
defconfigs.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
During very early prototype-phase we did boot the AM335x boards
initially from CPSW-EMAC.
Now we don't need this feature anymore.
So we drop it to save MLO-space and having therefore a more quickly
boot.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
Logic PD makes four different system on modules. This patch will auto
detect the board type and identify the corresponding device tree image.
V2:
Added 'default:' case to switch statement
Since board_late_init() is defined as int, we now return 0
Signed-off-by: Derald Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
check for U-Boot SPL signature only if SPL really has a serial output.
So check if CONFIG_SPL_SERIAL_SUPPORT is active in board config.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Building pci_rom.c with my toolchain complains about may be used uninitialized
rom varaible:
---8<---
+drivers/pci/pci_rom.c:269:25: note: 'rom' was declared here
w+drivers/pci/pci_rom.c: In function 'dm_pci_run_vga_bios':
w+drivers/pci/pci_rom.c:154:14: warning: 'rom' may be used uninitialized in this function [-Wmaybe-uninitialized]
--->8---
Fix this as done in 55616b86c7 the ram variable.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Compiling the mkorigenspl tool on darwin complains about undefined ulong. Fix
this by using the unified way.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since OpenSSL is deprecated on OS X in favour of Common Crypto API disable the
warning for this host OS.
Another solution would be to add some glue layer for crypto stuff, but I think
this is not worth the effort.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To follow the MIPS 32-bit and 64-bit memory map conventions (*) recent
MIPS Linux kernels are using a 64-bit sign extended value
(0xffffffff80010000) for the 32-bit load address (0x80010000) of the
Creator CI20 board kernel. When this 64-bit argument was passed to
mkimage running on a 32-bit machine such as the Creator CI20 board the
load address was incorrectly formed from the upper 32-bit sign-extend
bits (0xffffffff) by the strtoul instead of from the lower 32-bits
(0x80010000). The mkimage should be able to tolerate the longer
sign-extended 64-bit version of the 32-bit arguments with the use of
strtoull. Use of the strtoll in place of the strtol in mkimage.c
resolves the issue of self hosted kernel builds for the Creator CI20
board (+) and (++).
(*) http://techpubs.sgi.com/library/dynaweb_docs/0620/SGI_Developer/books/DevDriver_PG/sgi_html/ch01.html
(+) https://github.com/MIPS/CI20_linux/issues/23
(++) https://github.com/MIPS/CI20_linux/issues/22
Signed-off-by: William Cohen <wcohen@redhat.com>
This patch adds support for stm32f7 family usart peripheral.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Base addresses for GPIOs could be different for different socs, this
patch moves the base addresses from driver to the soc specific location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This patch removes the gpio clock enable from gpio driver & move it in the
board code, making it possible to use the gpio driver with other socs.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The following patch caused cpu_eth_init() to not be called anymore
for DM-capable boards:
commit c32a6fd07b
Date: Sun Jan 17 14:51:56 2016 -0700
net: Don't call board/cpu_eth_init() with driver model
This breaks ethernet on SoCFPGA, since we use that function to un-reset
the ethernet blocks. Invoke the ethernet reset function from arch_misc_init()
instead to fix the breakage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Don't understand how it happened, but this change got applied twice!
Therefore, removing the duplicated items.
Signed-off-by: Steve Rae <srae@broadcom.com>
Fix the formatting in error messages, and demote one error message
to a warning, as it is only informational.
Signed-off-by: Steve Rae <srae@broadcom.com>
The alignment and size were swapped, leading to malloc heap corruption.
On my system, this sometimes caused U-Boot to crash during or after
certain USB Ethernet operations.
Fixes: c8c2797c38 ("dm: usb: eth: Support driver model with USB Ethernet")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As tested on the Odroid XU3, large files to be stored on the file system
require considerable time to be physically written to the medium.
The default 300 ms is not enough to store large file (e.g. 26 MiB).
To fix this situation the DFU_MANIFEST_POLL_TIMEOUT has been defined.
It is used to cease the communication with dfu-util and allow the target
board to store the data on file system.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This patch fixes situation when one would like to write large file into
medium with the file system (fat, ext4, etc).
This change sets file size limitation to the DFU internal buffer size.
Since u-boot is not supporting interrupts and seek on file systems, it
becomes challenging to store large file appropriately.
To reproduce this error - create large file (around 26 MiB) and sent it
to the target board.
Lets examine the flow of USB transactions:
0. DFU uses EP0 with 64B MPS [Max Packet Size]
1. Send file - OUT (PC->target) - dat_26MiB.img is sent with 4096 B transactions
2. Get status - OUT (PC->target) - wait for DFU_STATE_dfuDNLOAD_IDLE (0x05) sent
from target board - IN transaction
(target->PC)
3. The whole file content is sent to target - OUT (PC->target) with ZLP [Zero
Length Packet]
Now the interesting part starts:
4. OUT (PC->target) Setup transaction (request to share DFU state)
5. IN (target->PC) - reply the current DFU state
- In the UDC driver the req->completion (with dfu_flush) is called
after successful IN transfer.
- The dfu_flush() (called from req->completion callback) saves the
whole file at once (u-boot doesn't support seek on fs).
Such operation takes considerable time. When the file
is large - e.g. 26MiB - this time may be more than 5 seconds.
6. OUT (PC->target) - ZLP, is send in the same time when dfu_flush()
writes data to eMMC memory.
The dfu-util application has hard coded timeout on USB transaction
completion set to 5 seconds (it uses libusb calls).
When the file to store is large (e.g. 26 MiB) the time needed to write it
may excess the dfu-util timeout and following error message will be displayed:
"unable to read DFU status" on the HOST PC console.
This change is supposed to leverage DFU's part responsible for storing files
on file systems. Other DFU operations - i.e. raw/partition write to NAND and
eMMC should work as before.
The only functional change is the error reporting. When dfu_flush() fails
the u-boot prompt will exit with error information and dfu-util application
exits afterwards as well.
Test HW:
- Odroid XU3 (Exynos5433) - test with large file
- Trats (Exynos4210) - test for regression - eMMC, raw,
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reported-by: Alex Gdalevich <agdalevich@axion-biosystems.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Heiko Schocher <hs@denx.de>
Add explicit cpu_to_be32()/be32_to_cpu() conversion to BE EHCI I/O
accessors to align them with their LE counterpart. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
If the USB EHCI is configured for little endian MMIO, make sure to
clear the USBMODE_BE flag from the USBMODE register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Certain processor architectures, like MIPS, require that the USB
structures and transfer buffers are passed with their PA to the
USB controller. If VA is passed, the USB will not work. Add the
necessary virt_to_phys() calls into the USB EHCI code to make it
work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Some architectures, like MIPS, require remapping of the registers.
Add the map_physmem() call to handle it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
The initialization for smmu and stream id is moved into the common soc
code.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QE-HDLC and USB multi-use the pins, modify the pin-muxing code
for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins
to QE-HDLC, if not, assgin it to USB
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Pin-muxing code should be in config_board_mux, move USB muxing
config to config_board_mux.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
there are some code in qe.c not used for micro QE,
use "#ifdef CONFIG_QE" to mask them.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use fdt32_to_cpu() to convert the data correctly for both endianness
platforms.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Before Linux boot DPL must be deployed to DPAA2 interface.
So update bootcmd env variable to make sure DPL deployment before
Linux boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define mcinitcmd env variable to load Management complex during
u-boot boot sequence.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory controller performance is not optimal with default internal
target queue register value, write required value for optimal DDR
performance.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.
The patch reverts commit 7cad2e38d6.
The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The output ring needs to be invalidated before enqueuing the job to SEC.
While allocation of space to output ring, it should be taken care that the
size is cacheline size aligned inorder to prevent invalidating valid data.
The patch also correct the method of aligning end of structs while flushing caches
Since start = align(start_of_struct), it is incorrect to assign
end = align(start + struct_size). It should instead be,
end = align(start_of_struct + struct_size).
Signed-off-by: Saksham Jain <saksham@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
enable dma driver model for am437x_sk_evm as ti-edma3 supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When CONFIG_DMA is defined the default spi_flash_copy_mmap() can
handle dma memory copy, so compile out spi_flash_copy_mmap() from
ti_qspi driver when CONFIG_DMA config is defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add dma memcpy api to the default spi_flash_copy_mmap(), so that
dma will be used to copy data when CONFIG_DMA is defined for the
platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Implement a DMA uclass so that the devices like ethernet, spi,
mmc etc can offload the data transfers from/to the device and
memory.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Zybo contains on board HDMI that's why enable EDID.
Doing it via config because zynq i2c driver hasn't been moved to DM yet
and enabling via Kconfig requires DM_I2C.
This will be moved that driver is moved to DM.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTS syncup with Linux kernel.
Add missing reset-gpio property.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The problem with current implementation is that SPDDONE bit is 1
but link bit is zero. That's why phydev->link is setup to 0
which ending up in driver failure that link is not up.
Log:
Zynq> dhcp
ethernet@e000b000 Waiting for PHY auto negotiation to complete.......
done
ethernet@e000b000: No link.
There is at least 1ms delay between spddone bit and link up.
Use genphy_read_status() instead of realtek implemenation which is
working with page 11. Linux driver is also using generic implementation.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync logic with Linux kernel where TX empty flag is checked before char
is sent.
This logic is fixing problem with console on zynqmp platform.
For example:
DRAM: 2 GiB
Enabling Caches...
EL Level: �� sdhci@ff170000: 0
Using default environment
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Remove CONFIG_ZYNQ_BOOT_FREEBSD configuration option and setup
CONFIG_SYS_MMC_MAX_DEVICE 1 for all Zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When the resolution is not supported we should free the memory we don't plan
to use.
Reported-by: Coverity (CID: 135127)
Signed-off-by: Simon Glass <sjg@chromium.org>
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.
This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce macros and command to support booting M4 core for
i.MX7D SabreSD board.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce macros and command to support booting M4 core for
i.MX6SX SabreSD board.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To boot a auxiliary core in asymmetric multicore system, introduce the
new command "bootaux" to do it. Example of boot auxliary core from
0x70000000 where stores the boot head information that should be
parsed by auxiliary core, "bootaux 0x70000000".
Introduce Kconfig option IMX_BOOTAUX.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the peripherals/masters definitions and registers base addresses
for mx7d RDC.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce Resource Domain Controller support for i.MX.
Now i.MX6SX and i.MX7D supports this feature to assign masters
and peripherals to different domains.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introudce rdc regs structure and rdc sema reg structure for i.MX6.
For now, to i.MX6, only i.MX6SX supports this.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Specify max_bus_width directly in usdhc_cfg static definition instead
of tweaking it in the board_mmc_init() function.
Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
commit 216d286c7e [imx: mx6: implement
mmc_get_env_dev] introduced selection of the environment device according
to the boot device when booting from SD/MMC.
Extend this functionality for also selecting the device partition.
Signed-off-by: Soeren Moch <smoch@web.de>
Introudce i.MX7 pinctrl driver support.
For now only i.MX7D supported.
There are two iomux controllers in i.MX7D, iomuxc and iomuxc_lpsr.
To iomuxc_lpsr, ZERO_OFFSET_VALID is set, means offset of mux_reg
and conf_reg can begin at 0.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce pinctrl for i.MX6
1. pinctrl-imx.c is for common usage. It's used by i.MX6/7.
2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry.
3. To the pinctrl_ops implementation, only set_state is implemented.
To i.MX6/7, the pinctrl dts entry is as following:
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
>;
};
[.....]
};
there is no property named function or groups. So pinctrl_generic_set_state
can not be used here.
5. This driver is a simple implementation for i.mx iomux controller,
only parse the fsl,pins property and write value to registers.
6. With DEBUG enabled, we can see log when "i2c bus 0":
"
set_state_simple op missing
imx_pinctrl_set_state: i2c1grp
mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x14c val 0x10
select_input: offset 0x5d8 val 0x1
write config: offset 0x3bc val 0x7f
mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x148 val 0x10
select_input: offset 0x5d4 val 0x1
write config: offset 0x3b8 val 0x7f
"
this means imx6 pinctrl driver works as expected.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactored data structure for CAAM's job ring and Secure Memory
to support i.MX7.
The new memory map use macros to resolve SM's offset by version.
This will solve the versioning issue caused by the new version of
secure memory of i.MX7
Signed-off-by: Ulises Cardenas <raul.casas@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
When running the 'ums' command we get:
=> ums 0 mmc 0
UMS: disk start sector: 0x0, count: 0xe18000
g_dnl_register: failed!, error: -22
ERROR: g_dnl_register failed
at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage()
Fix this by initializing USB OTG1 port as USB device mode instead of host.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Select CONFIG_FSL_QSPI so that the SPI can be probed:
=> sf probe
SF: Detected N25Q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Commit 276d3ebb88 removed htole32() but missed
to remove the corresponding header. This is annoying, since BSD systems do not
have endian.h.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Michael Heimpold <mhei@heimpold.de>
Update existing documentation to mention Intel Bayley Bay board
instructions, an additional Bay Trail based board to MinnowMax.
This also adds a minor change to QEMU section to indicate clearly
the instructions are for bare mode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Wrap initialization codes with #ifndef CONFIG_HAVE_FSP #endif,
and enable the build for both FSP and non-FSP configurations.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Intel IvyBridge FSP seems to be buggy that it does not report memory
used by FSP itself as reserved in the resource descriptor HOB. The
FSP specification does not describe how resource descriptor HOBs are
generated by the FSP to describe what memory regions. It looks newer
FSPs like Queensbay and BayTrail do not have such issue. This causes
U-Boot relocation overwrites the important boot service data which is
used by FSP, and the subsequent call to fsp_notify() will fail.
To resolve this, we find out the lowest memory base address allocated
by FSP for the boot service data when walking through the HOB list in
fsp_get_usable_lowmem_top(). Check whether the memory top address is
below the FSP HOB list, and if not, use the lowest memory base address
allocated by FSP as the memory top address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on link (ivybridge non-FSP)
Tested-by: Simon Glass <sjg@chromium.org>
The SMSC SIO1007 superio chipset integrates two ns16550 compatible
serial ports for legacy applications, 16 GPIO pins and some other
functionalities like power management.
This adds a simple driver to enable serial port and handle GPIO.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
IvyBridge FSP package is built with a base address at 0xfff80000,
and does not use UPD data region. This adds basic FSP support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on link (ivybridge non-FSP)
Tested-by: Simon Glass <sjg@chromium.org>
Purely by code inspection, it looks like the parameter order to memalign()
is swapped; its parameters are (align, size). 4096 is a likely desired
alignment, and a variable named size sounds like a size:-)
Fixes: 45b5a37836 ("x86: Add multi-processor init")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With release of ARC HS38 v2.1 new IO coherency engine could be built-in
ARC core. This hardware module ensures coherency between DMA-ed data
from peripherals and L2 cache.
With L2 and IOC enabled there's no overhead for L2 cache manual
maintenance which results in significantly improved IO bandwidth.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARC core could be configured with different L1 and L2 (AKA SLC) cache
line lengths. At least these values are possible and were really used:
32, 64 or 128 bytes.
Current implementation requires cache line to be selected upon U-Boot
configuration and then it will only work on matching hardware. Indeed
this is quite efficient because cache line length gets hardcoded during
code compilation. But OTOH it makes binary less portable.
With this commit we allow U-Boot to determine real L1 cache line length
early in runtime and use this value later on. This extends portability
of U-Boot binary a lot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The SAMA5D2 has a second internal SRAM that can be reassigned as a L2
cache memory.
Make sure it is configured as a L2 cache memory when booting from a SPL
image.
Based on the commit b5ea95ef2b5b from the at91bootstrap repository.
Signed-off-by: Samuel Mescoff <samuel.mescoff@mobile-devices.fr>
Reviewed-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the PMC_PLLICPR init function, use this
function to clean up the code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the PMC_PLLICPR init function, use this
function to clean up the code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new PLLB clock handle functions,
use these functions to clean up the PLLB enable code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Due to introducing the new PLLB clock handle functions,
use these functions to clean up the PLLB enable/disable code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Due to introducing the new UTMI PLL clock handle functions,
use the functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new UTMI PLL clock handle functions,
use these function to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the UTMI PLL enable function, use this function
to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To avoid the duplicated code, add the UTMI PLL handle functions,
and add PMC_USB init function too.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[fixup for missing clk.h in at91_emac.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[Rebased on current master, fixup for at91rm9200ek]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to clean up the duplicated code.
Meanwhile, remove unneeded header file include, at91_pmc.h.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixup for arm920t code]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
To reduce the duplicated code, add a new file to accommodate
the peripheral's and system's clock handle code, shared with
the SoCs with different ARM core.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
With commit a058052c [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Resulting in bit 12
being cleared (A/N enable). This leads to autonegotiation link problems,
at least on the Marvell Armada ClearFog board. I suspect that other
boards using this driver will be affected as well.
At the of m88e1111s_config(), phy_reset() is called. This is not needed
for the PHY to load the changed configuration, as phy_reset() is called
a few lines before already. So lets call genphy_restart_aneg() here
instead to start the AN correctly.
Tested on clearfog.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This allows U-Boot to expose UMS and DFU protocols on this port in device
mode, or to act as a USB host on the port, using an "OTG" (micro-B to
female A host) cable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option is no longer used now that DM_USB is enabled.
Fixes: 534f9d3fef ("dm: tegra: usb: Move USB to driver model")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This new feature causes a Kconfig warning on boards without a display
enabled. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove the old PWM code. Remove calls to CONFIG_LCD functions now that we
are using driver model for video.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use the driver-model PWM driver in preference to the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this option to Kconfig and clean up the header files. Adjust the only
user (the LCD driver) to work with the new driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Join the two functions which decode the device tree and put them in the
ofdata_to_platdata() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no need to have these in a separate file as they are not
referenced from anywhere else.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We can move the static variables into the driver-private data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We have a structure for the display panel and another for the controller.
There is some overlap between them. Merge them to simplify the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present we have code in arch/arm and code in drivers/video. Move it all
into drivers/video since it is a display driver and our current approach is
to put all driver code in drivers/.
Make a few functions static now that they are not used outside the file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This file has changed quite a bit since it was set up. Sync it back with
Linux v4.4. Adjust the users slightly to cope with the changes:
- the host1x node is now called host1x@50000000
- we need a clocks node to provide the clk32k_in phandle
- active usb nodes need status = "okay"
- active i2c nodes need status = "okay"
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While we transition to using driver model for video, we need to support both
options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We can skip this manual init when using driver model for the PWM.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There isn't a lot of benefit of have two separate files. With driver model
the code needs to be in the same driver, so it's better to have it in the
same file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This PWM supports four channels. The driver always uses the 32KHz clock,
and adjusts the duty cycle accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The tegra GPIO controller has two ways of reading the value of a GPIO. It
can supply the 'input' value (which is the value read from the pin) and the
'output' value (which is the value being driven from the pin. With a GPIO
set to output mode, the 'input' value is always low which is not very
useful.
This has the unfortunate result that setting a GPIO high still leaves it
showing as low in the 'gpio status' command.
Adjust the driver to check which direction the GPIO is set to, then read
the value from the appropriate register: 'input' for input GPIOs, 'output'
for output GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sync up these files with Linux v4.4. Some differences remain, principally
that the addresses are still 32-bit in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This helps keep the display consistent. puts() is used when printing the
prompt, so is a useful way to make sure the current display contents is
visible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We need to add the base tables before adding the function tables. Fix the
init order so the keyboard scans keys correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The initial boot of U-Boot happens within the context of the first test
that needs to access the U-Boot console when there is no existing
connection. This keeps all activity nestled within test execution, which
fits well into the pytest model. However, this mingles the U-Boot startup
logs with the execution of some test(s), which hides find the boundary
between the two.
To solve this, wrap the "Starting U-Boot" logic into a separate log
section. If the user wishes, they can simply collapse this log section
when viewing the HTML log, to concentrate purely on the test's own
interaction.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
u_boot_console.exec_attach.get_spawn() performs two steps:
1) Spawn a process to communicate with the serial console.
2) Reset the board so that U-Boot starts running from scratch.
Currently, if an exception happens in step (2), no cleanup is performed on
the process created in step (1). That process stays running and may e.g.
hold serial port locks, or simply continue to read data from the serial
port, thus preventing it from reaching any other process that attempts to
read from the same serial port later. While there is error cleanup code in
u_boot_console_base.ensure_spawned(), this is not triggered since the
exception prevents assignment to self.p there, and hence the exception
handler has no object to operate upon in cleanup_spawn().
Solve this by enhancing u_boot_console.exec_attach.get_spawn() to clean
up any objects it has created.
In theory, u_boot_spawn.Spawn's constructor has a similar issue, so fix
this too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use lists rather than sets to record the status of tests. This causes
the test summary in the HTML file to be generated in the same order as
the tests are (or would have been) run. This makes it easier to locate
the first failed test. The log for this test might have interesting
first clues re: interaction with the environment (e.g. hardware flashing,
serial console, ...) and may help tracking down external issues.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Python ini file parser that's used to parse .config converts all keys
to lower-case. Hence, all queries against the results must use lower-case.
Fix u_boot_console.ensure_spawned() to test CONFIG_SPL correctly, or the
connection will fail for boards that have SPL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This provides runtime test coverage in Travis, in addition to the existing
build coverage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
The code replaced pexpect with custom code long ago. Don't import the
unused module so it doesn't need to be installed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add documentation describing the new --gdbserver feature, and some common
pytest options.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Invoke each "ut"-based unit test as a separate pytest.
Now that the DM unit test runs under test/py, remove the manual shell
script that invokes it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # v2, on sandbox
This information may be useful for both debugging, and processes that want
to perform simple forms of introspection on the U-Boot binary, such as
determining the set of "ut" subtests that are compiled in.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is broken - we need to look at the first two characters to distinguish
'gpio status' from 'gpio set'.
Fixes: 0ffe6ab5 (gpio: Allow 's' as an abbreviation for 'status')
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
$ make tools-all
...
In file included from tools/env/env_flags.c:1:0:
tools/env/../../common/env_flags.c: In function
‘env_flags_parse_varaccess_from_binflags’:
tools/env/../../common/env_flags.c:156:18: warning: implicit declaration
of function ‘ARRAY_SIZE’ [-Wimplicit-function-declaration]
for (i = 0; i < ARRAY_SIZE(env_flags_varaccess_mask); i++)
^
Seems like the other utilities just add a copy of ARRAY_SIZE since
there's nowhere to include it from (tools/imagetool.h,
tools/mxsimage.h). Let's do the same here.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
The kernel gets much too sad when the ramdisk is loaded too high into the 1GiB
of memory on Raspberry Pi 2:
## Flattened Device Tree blob at 00000100
Booting using the fdt blob at 0x000100
Loading Ramdisk to 39c14000, end 3ab45067 ... OK
Using Device Tree in place at 00000100, end 000045ea
...
[ 0.599346] Unpacking initramfs...
[ 0.602924] Unable to handle kernel paging request at virtual address f9c14000
Placement of the device tree was fixed in 89ca1000 (ARM: rpi: set fdt_high
in the default environment).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
If BUILD_TAG is part of KBUILD_CFLAGS, then any time the value changes,
all files get rebuilt. In a continuous integration environment, the value
will change every build. This wastes time, assuming that incremental
builds would otherwise occur.
To solve this, remove BUILD_TAG from KBUILD_CFLAGS and add it to CFLAGS
for just the one file that uses it. This does have the disadvantage that
if any other files want to use the flag, we'll need to duplicate this
custom CFLAGS setup logic. However, it seems unlikely we'll need this.
An alternative would be to add BUILD_TAG to the "local version" and remove
the special case code from display_options.c. However, that would affect
the format of the U-Boot signon message, which may negatively affect
people looking for specific data there. The approach of using
file-specific CFLAGS was suggested by Masahiro Yamada.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the recent addition of UBI support, this patch will add the preset
parameters to allow for mouting an UBIFS from the 'fs' partition in NAND.
-V2: ubi.mtd=fs instead of ubi.mtd=4
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SF_DEFAULT_MODE is used to select default SPI mode when using
sf commands. Therefore fix am43xx to use CONFIG_SF_DEFAULT_MODE instead
of CONFIG_DEFAULT_SPI_MODE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
I will take this over from Peter Barada, since I work with it daily
at Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peter Barada <peter.barada@logicpd.com>
Based on the work done by Overo, this seems to help some compilers
that have a hard time fitting all the code into the allocated space.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Boot with the Linux zImage and am3517-evm.dtb pair, when SD/MMC media
is present. This behavior can be overridden by creating a 'uEnv.txt'
file with 'uenvcmd' defined.
To boot an existing 'uImage', create the following 'uEnv.txt':
[start]-----------------------------------------------------------------
loaduimage=fatload mmc 0:1 ${loadaddr} ${bootfile}
uenvcmd=run loaduimage; run mmcargs; bootm ${loadaddr}
[end]-------------------------------------------------------------------
Inspired by similar patches, for other OMAP3 boards, from EEWiki
- https://github.com/eewiki/u-boot-patches/tree/master/v2016.01
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Initial commit for PH1-Pro4 Ace and Sanji boards.
Note:
There are two variants for the Ace board in terms of the amount of
DDR memory; 1GB or 2GB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This board has an EEPROM connected to the I2C channel 0 of the SoC.
Its slave address is 0x54.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This environment define has been here to work around the LMB
allocation error introduced by commit 9c11135ce0 ("image: fix
getenv_bootm_size() function").
It is no longer needed because the root cause was fixed by commit
0cb389dd1a ("image: fix getenv_bootm_size() function again").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It turned out that DDR channel 2 was not working on ProXstream2
Vodka board. Add the missing ACBLDR0 register setting to adjust
the delay between the clock lines and the address/command lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_CMD_DDRMPHY_DUMP is enabled, the build fails.
Fixes: 93d92d46cd ("ARM: uniphier: add dump command for DDR Multi PHY registers")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The U-Boot proper building needs to descend arch/arm/mach-uniphier/dram
to build these commands.
Fixes: 93d92d46cd ("ARM: uniphier: add dump command for DDR Multi PHY registers")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This header is no longer used.
This is the last file in arch/arm/mach-uniphier/include/mach/.
At last, I've succeeded in eliminating the mach directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, all this driver does can be covered by the generic EHCI driver
(drivers/usb/host/ehci-generic.c). UniPhier SoCs have switched to
use it. Delete this driver rather than bothering to convert it to
Driver Model.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
The UniPhier EHCI driver (drivers/usb/host/ehci-uniphier.c) does
nothing special but set the base address and handle reset/clock.
Since commit 4feefdcfe9 ("usb: add clock support for generic EHCI"),
the generic one (drivers/usb/host/ehci-generic.c) can do those, too.
We no longer need to stick to the dedicated driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This block provides clock and reset control for MIO (Media I/O)
hardware blocks such as USB2.0, SD card, eMMC, etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This block provides clock and reset control for peripherals such as
UART, I2C, IC card, etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the initial commit for the UniPhier clock drivers.
Currently, only the Media I/O clock is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The USB boot code is too fat and complicated to be included in SPL
(at least for now). So, it was implemented as a separate project
(what we call USB-loader).
The expected boot sequence is as follows:
Boot ROM -> USB-loader -> SPL -> U-Boot proper
The USB-loader loads the SPL and U-Boot proper from a USB memory
onto the locked L2 cache. Then, SPL needs to copy the U-Boot proper
to DRAM, so this mode looks like a NOR boot from the view of SPL.
However, we want to distinguish between (genuine) NOR boot and USB
boot in some places.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier SoCs are not equipped with dedicated on-chip SRAM. Instead,
locked outer cache is used as RAM area during the early boot stage
where DRAM is not ready yet. This effectively means MMU must be
always enabled while we are in SPL.
Currently, the SPL image for UniPhier SoCs contains the page table
statically defined at compile time. It has been a burden because the
16KB page table occupies a quarter memory footprint of the 64KB SPL
image.
Finally, there is no more room to implement new features in SPL.
Setting aside the NOR boot mode, this issue can be solved by creating
the page table onto RAM at run time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No special reason for the current stack address 0x0ff08000.
Change it to 0x00100000 to simplify the init_page_table.
There are two types of SoCs in terms of the load address of SPL.
[1] PH1-sLD3, PH1-LD4, PH1-sLD8
SPL is loaded at 0x00040000-0x0004ffff
[2] PH1-Pro4, PH1-Pro5, ProXstream2, PH1-LD6b
SPL is loaded at 0x00100000-0x0010ffff
The new stack area (0x000f8000-0x00100000) should be safe for all the
cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit ad1ecd2063 ("fdt: Build a U-Boot binary without device
tree") and commit 03c25bcd26 ("fdt: Build an SPL binary without
device tree"), we can use shorter file names for the output images.
The default configuration for UniPhier SoCs enables CONFIG_OF_SEPARATE
and CONFIG_SPL_OF_CONTROL. In this case, spl/u-boot-spl.bin is the
same as spl/u-boot-spl-dtb.bin. Likewise, u-boot.img is the same as
as u-boot-dtb.img. So, this change of the flow has no impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some of PH1-Pro4 boards are equipped with larger amount of DRAM than
the reference board. Add UMC settings to support them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The environment "bootm_low" is updated before the "bootz" command.
This is common for all the boot modes (NOR, NAND, TFTP, etc.), so
can be factored out.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 25d4eb8091 ("ARM: uniphier: add bootm_low environment")
missed to add "bootm_low" for FIT boot. Set "bootm_low" to the
DRAM base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 89835b3557 ("ARM: uniphier: allow to run zImage rather than
uImage") changed the kernel boot commands. Unlike "bootm", "bootz"
does not relocate the kernel image. When the boot device is a NOR
flash, the zImage should be copied from the NOR onto the DRAM before
it is passed to the "bootz" command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
The allocation size is reduced from what was introduced from the
Linux kernel, as U-boot uses the statically allocated nand_info
instead of needing to dynamically allocate an mtd_info instance.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Correct some pointer math in initialization. An offset was added
to a struct-typed pointer instead of one casted to a byte-size,
resulting in a much larger offset than intended.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Correct a null pointer dereference in board_nand_init(). Zeroed
memory was allocated, then immediately dereferenced. The
dereference is completely removed, since this pointer is later
initialized in alloc_nand_resources.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
Fix error handling for mxs_nand_init.
The original error handling is wrong for err2 and err1.
Should first free desc[x], then free desc.
This patch also correctly handle err3, should use
MXS_DMA_CHANNEL_AHB_APBH_GPMI0 as the check point.
Cc: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Boards with a saved environment may use 'lcd' in their stdout environment
variable, expecting that this will enable output to the LCD. When the board
moves to use driver model for video, this will no-longer work. Add a
work-around to fix this. A warning messages is printed, and we will remove
the work-around at the end of 2016.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
This commit breaks bootup on sunxi boards, the get stuck
when running the main u-boot binary at:
CPU: Allwinner H3 (SUN8I)
I2C: ready
DRAM:
This reverts commit 8e7cba048b.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The existing regex simply ensures that the captured version string doesn't
go past the end of a line. We really want to grab as much as possible. Do
this by explicitly including a ) character at the end of the regex to
match the last character of the version test.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A regex match object's .end() value is already the index after the match,
not the index of the last character in the match, so there's no need to
add 1 to point past the match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Implement three improvements to the HTML log file:
- Ability to expand/contract sections. All passing sections are contracted
at file load time so the user can concentrate on issues requiring
action.
- The overall status report is copied to the top of the log for easy
access.
- Add links from the status report to the test logs, for easy navigation.
This all relies on Javascript and the jquery library. If the user doesn't
have Javascript enabled, or jquery can't be downloaded, the log should
look and behave identically to how it did before this patch.
A few notes on the diff:
- A few more 'with log.section("xxx")' were added, so that all stream
blocks are kept within a section block for consistent HTML entity
nesting structure. This changed indentation in a few places, making
the diff look slightly larger.
- HTML entity IDs are cleaned up. We assign simple incrementing integer
IDs now, rather than using mangled test names which were possibly
invalid.
- Sections and streams now use common CSS class names (in addition to the
current separate class names) to more easily share the new behaviour.
This also reduces the CSS file size since rules don't need to be
duplicated.
- An "OK" status is logged after some external command executions so that
make and flash steps are auto-contracted at log file load time, assuming
they passed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The test/py/test.py wrapper script catches exceptions thrown when
exec()ing py.test in order to print a helpful error message. However,
the exception handling code squashes the exception and so the script
exits with a non-zero exit code, leading callers to believe that it
passed. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
On some systems, RAM starts at address 0. If the user executes itest
against address 0 on such a system, it will call map_physmem(0, ...)
which will return 0 back; mapping only changes the address on sandbox.
This causes itest to believe map_physmem() has failed, and hence fails
the comparison.
Fix itest so that it allows map_physmem() to return 0 /if/ the orignal
address passed to it was also 0.
This fixes "tegra-uboot-flasher flash" on Tegra20.
This has the disadvantage that on sandbox, failed mapping attempts for
address 0 are not detected. Instead, should the code only call
map_physmem() on sandbox? Or, should map_physmem() return its error status
some other way. Or, should the special case only be allowed on systems
where the base of RAM is 0 somehow?
Fixes: 7861204c9a ("itest: make memory access work under sandbox")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Current, the following passes:
./u-boot -d arch/sandbox/dts/test.dtb -c 'ut_image_decomp'
but the following fails:
./u-boot -d arch/sandbox/dts/test.dtb -c 'ut dm; ut_image_decomp'
This is because the gunzip code reads input data beyond the end of its
input buffer. In the first case above, this data just happens to be 0,
which just happens to trigger gzip to signal the error the decompression
unit test expects. In the second case above, the "ut dm" test has written
data to the accidentally-read memory, which causes the gzip code to take a
different path and so return a different value, which triggers the test
failure.
The cause of gunzip reading past its input buffer is the re-calculation of
s.avail_in in zunzip(), since it can underflow. Not only is the formula
non-sensical (it uses the delta between two output buffer pointers to
calculate available input buffer size), it also appears to be unnecessary,
since the gunzip code already maintains this value itself. This patch
removes this re-calculation to avoid the underflow and redundant work.
The loop exit condition is also adjusted so that if inflate() has consumed
the entire input buffer, without indicating returning Z_STREAM_END (i.e.
decompression complete without error), an error is raised. There is still
opportunity to simplify the code here by splitting up the loop exit
condition into separate tests. However, this patch makes the minimum
modifications required to solve the problem at hand, in order to keep the
Acked-by: Kees Cook <keescook@chromium.org>
diff simple.
I am not entirely convinced that the loop in zunzip() is necessary at all.
It could only be useful if inflate() can return Z_BUF_ERROR (which
typically means that it needs more data in the input buffer, or more space
in the output buffer), even though Z_FINISH is set /and/ the full input is
available in the input buffer /and/ there is enough space to store the
decompressed output in the output buffer. The comment in zlib.h after the
prototype of inflate() implies this is never the case. However, I assume
there must have been some reason for introducing this loop in the first
place, as part of commit "Fix gunzip to work for any gziped uImage size".
This patch is similar to the earlier b75650d84d "gzip: correctly
bounds-check output buffer", which corrected a similar issue for
s.avail_out.
Cc: Catalin Radu <Catalin@VirtualMetrix.com>
Cc: Kees Cook <keescook@chromium.org>
Fixes: f039ada5c1 ("Fix gunzip to work for any gziped uImage size")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There are various different boards with the same hardware sold as LG Optimus
Black, such as P970, P970g and KU5900. Since this port is functional for all
variants, it doesn't make sense to keep references to P970.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The ARM Linux kernel requires the DT to be in memory accessible early
during the boot process. This always happens naturally on the RPi 1,
since the maximum memory size of 512MiB, and additionally some of that
is reserved for use by the GPU. The RPi 2 has 1GiB of RAM (minus some
GPU usage), and so if the DT is relocated to the top of RAM, Linux cannot
access it. Prevent this from happening by setting fdt_high.
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Update rpi-common.h's documentation that describes the rationale for
choosing various addresses for standardized variables used by boot
scripts. This comment was correct when written, but not updated when some
of the values were changed.
Fixes: 14006a5671 ("rpi: set fdt_addr_r to 0x00000100 to match default
...device_tree_address")
Cc: Jonathan Liu <net147@gmail.com>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The build command of u-boot-spl.dtb is not constant, but dependent
on CONFIG_OF_SPL_REMOVE_PROPS. Use $(call if_changed,...) so that
the change of CONFIG_OF_SPL_REMOVE_PROPS is detected.
Also, add tools/fdtgrep to the dependency to make sure u-boot-spl.dtb
is generated by the up-to-date fdtgrep in case the tool is modified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FORCE is needed for $(call if_changed,...) to be evaluated every time.
Otherwise, the command is not executed when the command line has
changed but any prerequisite has not been updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These rules are only used for SOCFPGA, SUNXI, but no need to hide
them from other SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 9c11135ce0 ("image: fix getenv_bootm_size() function") fixed
the case where "bootm_low" is defined, but "bootm_size" is not.
Instead, it broke the case where neither "bootm_low" nor "bootm_size"
is defined. Fix this function again.
Fixes: 9c11135ce0 ("image: fix getenv_bootm_size() function")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Matthias Weisser <m.weisser.m@gmail.com>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Implement command--line option --gdbserver COMM, which does two things:
a) Run the sandbox process under gdbserver, using COMM as gdbserver's
communication channel.
b) Disables all timeouts, so that if U-Boot is halted under the debugger,
tests don't fail. If the user gives up in the middle of a debugging
session, they can simply CTRL-C the test script to abort it.
This allows easy debugging of test failures without having to manually
re-create the failure conditions. Usage is:
Window 1:
./test/py/test.py --bd sandbox --gdbserver localhost:1234
Window 2:
gdb ./build-sandbox/u-boot -ex 'target remote localhost:1234'
When using this option, it likely makes sense to use pytest's -k option
to limit the set of tests that are executed.
Simply running U-Boot directly under gdb (rather than gdbserver) was
also considered. However, this was rejected because:
a) gdb's output would then be processed by the test script, and likely
confuse it causing false failures.
b) pytest by default hides stdout from tests, which would prevent the
user from interacting with gdb.
While gdb can be told to redirect the debugee's stdio to a separate
PTY, this would appear to leave gdb's stdio directed at the test
scripts and the debugee's stdio directed elsewhere, which is the
opposite of the desired effect. Perhaps some complicated PTY muxing
and process hierarchy could invert this. However, the current scheme
is simple to implement and use, so it doesn't seem worth complicating
matters.
c) Using gdbserver allows arbitrary debuggers to be used, even those with
a GUI. If the test scripts invoked the debugger themselves, they'd have
to know how to execute arbitary applications. While the user could hide
this all in a wrapper script, this feels like extra complication.
An interesting future idea might be a --gdb-screen option, which could
spawn both U-Boot and gdb separately, and spawn the screen into a newly
created window under screen. Similar options could be envisaged for
creating a new xterm/... too.
--gdbserver currently only supports sandbox, and not real hardware.
That's primarily because the test hooks are responsible for all aspects of
hardware control, so there's nothing for the test scripts themselves can
do to enable gdbserver on real hardware. We might consider introducing a
separate --disable-timeouts option to support use of debuggers on real
hardware, and having --gdbserver imply that option.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The recent change to memalign() caused the allocation failure detection
code to be dead code; the "retry" logic is always activated under the same
condition that the original failure detection code is, and also fully
handles any possible failures. This patch solves the presence of dead
code.
Two alternatives are possible:
a) Delete the now-dead test, and rely on the "retry" path to handle any
allocation problems, as it does.
b) Make the "retry" path fall through to the existing (currently dead)
failure detection code, thus making it not-dead.
(b) was chosen since it reduces the diff between U-Boot's and the upstream
dlmalloc. This should make it marginally easier to import a new version of
dlmalloc in the future.
Reported by: Coverity Scan
Fixes: 4f144a4164 ("malloc: work around some memalign fragmentation issues")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Without this, builds default to using new Travis CI infra-structure which
does no allow sudo. The builds need sudo in order to install the ELDK
compilers. Consequently, almost all builds fail without this.
I suspect that existing Travis CI users have not noticed this because
their accounts or builds have been grand-fathered into backwards-
compatible default settings, whereas I just set up a new build from
scratch and received new default settings.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Heiko Schocher <hs@denx.de>
Let's set "ethaddr" when we get the ethernet address too, so that
fdt_fixup_ethernet() sets the address in the device tree and the Linux
driver can pick it up.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The case of memory of size 0 is not that different from a memory of any other
size, so we remove the duplicate code and treat the small differences when it
is the case.
Signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
When Micrel phy is selected without CONFIG_PHY_MICREL_KSZ9031 or
CONFIG_PHY_MICREL_KSZ9021 there is a build error. Fixing this
by adding proper ifdefs
drivers/net/phy/micrel.c:370:39: error: array type has incomplete element type
static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
^
drivers/net/phy/micrel.c:372:39: error: array type has incomplete element type
static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
^
drivers/net/phy/micrel.c: In function ‘ksz9031_of_config’:
drivers/net/phy/micrel.c:377:23: error: array type has incomplete element type
struct ksz90x1_ofcfg ofcfg[] = {
^
drivers/net/phy/micrel.c:379:13: error: ‘ksz90x1_rxd_grp’ undeclared (first use in this function)
{ MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 2, ksz90x1_rxd_grp, 4 },
^
drivers/net/phy/micrel.c:379:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/phy/micrel.c:380:13: error: ‘ksz90x1_txd_grp’ undeclared (first use in this function)
{ MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 2, ksz90x1_txd_grp, 4 },
^
drivers/net/phy/micrel.c:386:3: warning: implicit declaration of function ‘ksz90x1_of_config_group’ [-Wimplicit-function-declaration]
ret = ksz90x1_of_config_group(phydev, &(ofcfg[i]));
^
drivers/net/phy/micrel.c:377:23: warning: unused variable ‘ofcfg’ [-Wunused-variable]
struct ksz90x1_ofcfg ofcfg[] = {
^
drivers/net/phy/micrel.c: At top level:
drivers/net/phy/micrel.c:370:39: warning: ‘ksz9031_ctl_grp’ defined but not used [-Wunused-variable]
static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
^
drivers/net/phy/micrel.c:372:39: warning: ‘ksz9031_clk_grp’ defined but not used [-Wunused-variable]
static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
^
scripts/Makefile.build:277: recipe for target 'drivers/net/phy/micrel.o' failed
make[1]: *** [drivers/net/phy/micrel.o] Error 1
Makefile:1201: recipe for target 'drivers/net/phy' failed
make: *** [drivers/net/phy] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
UBIFS is the preferred FS, and YAFFS isn't officially included in
Linux. Removing this feature reduces the code size.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The interface automatically converts one 32-bit word into two 16 words.
The README said it is permissible to use this flag in that scenario.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic.
This patch sets up the USB gadget and Android Fastboot to match what is done in the
omap3_beagle project.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Previously, Omap3_logic assumed X-loader was present. With this
patch, we can finally replace X-loader with an MLO generated by
U-Boot. This requires ECC to be setup to match the Linux Kernel
and the PBIAS confgured for the SD card.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The P5 header was not present on "Model B" any board prior to Revision 2.0,
there's no need for a separate device tree.
Also, it looks like "rev2" is incorrectly used to only cover the 512MiB
memory models; there also were 256MiB 2.0 boards.
I don't have all of the boards to check this, I'm following this table:
http://elinux.org/RPi_HardwareHistory#Board_Revision_History
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
This source has been blessed by Dom Cobley at the RPi Foundation, so seems
like the best source to refer to. It's a superset of and consistent with
the other sources.
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add trivial support for changing the U-Boot command prompt string
by setting PS1 and PS2 environment variables. Only static variables
are supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pull the code which displays U-Boot prompt and reads the command line
into a separate function. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch removes the uart clock enable from serial driver & move it in the
board code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
disabled original parsing, but not yet removed since the
argument indexing needs to be fixed
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
goal is to use getopt for all argument parsing instead of adhoc
parsing in fw_getenv/fw_setenv functions
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
The FB address is generated by the firmware running on the GPU/VideoCore
and is a "bus" address. This address is the other side of an IOMMU from
the ARM upon which U-Boot is running. Use bus_to_phys() to convert this
to an ARM physical address. Without this, U-Boot seems to work just fine,
but once the Linux kernel boots on an RPi2, accessing the FB memory often
causes a hard system hang.
This is related to:
122426d46e ARM: bcm2835: use phys_to_bus() for mbox
5c0beb5c58 usb: dwc2: use phys_to_bus/bus_to_phys
79340db7f1 ARM: bcm2835: implement phys_to_bus/bus_to_phys
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
emac module of the davinci platform supports only 8 tx and 8
rx channels (total 16). emac driver for davinci platform,
however, while doing initialization of the dma descriptor
head pointers, wrongly initializes the 16 head pointers
(instead of 8) for tx dma and 16 head pointers (insted of 8)
for rx dma, which is wrong. The result is, that this register
initilization spills over the other registers which was not
intended and is undesirable. This patch fixes this problem.
Signed-off-by: Vishwas Srivastava <vishu.kernel@gmail.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The option was renamed to CONFIG_CONSOLE_ROTATION and Rockchip boards
were not updated. However this option is is not needed by default for
Rockchip since we don't need a rotated console for current boards. So just
remove the old option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use __maybe_unused which should avoid the Coverity error.
Reported-by: Coverity (CID: 134900)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Close the file earlier to hopefully fix a Coverity error.
Reported-by: Coverity (CID: 134901)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Using short doesn't save anything and is confusing when the width and height
variables are ulong.
This may fix Coverity CID134902 but I doubt it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All paths should share the same return.
Reported-by: Coverity (CID:134903)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This fixes the following error when building microblaze-generic:
net/eth-uclass.c: In function 'eth_post_probe':
net/eth-uclass.c:466:18: error: 'gd' undeclared (first use in this function)
ops->start += gd->reloc_off;
Fixes: db9391e1 ("net: Move driver-model code into its own file")
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Set up the debug UART early if enabled, so that it is ready to use.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Now that we have converted all x86 codes to DM PCI, drop pci_type1.c
which is only built for legacy PCI. Also per checkpatch.pl warning,
DEFINE_PCI_DEVICE_TABLE is now deprecated so drop that too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that all x86 codes have been converted to use proper DM PCI APIs,
it's time to disable the legacy compatible layer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When CONFIG_DM_PCI_COMPAT is not on, there is only a forward declaration
for pci_write_config32(). Add other missing ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board uses RTL8169 which is a driver model ethernet driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the RTL8169 driver warning is fixed we can drop this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It does not build if without CONFIG_DM_PCI_COMPAT. For now we just
disable it, until some day we add USB support to EFI application.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move some #undef from efi-x86.h to efi-x86_defconfig as these are
already Kconfig options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are still two places in Quark's MRC codes that use the generic
legacy PCI APIs, but as we are phasing out these legacy APIs, switch
to use Quark's own PCI config routines.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have converted all x86 codes to use DM PCI APIs,
drop those legacy ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
With recent DM PCI changes to vesa_fb driver, external graphics
card does not work any more. This is because: after setting the
function disable bit, IGD and SDVO devices will disappear in the
PCI configuration space. This however creates an inconsistent state
from a driver model PCI controller point of view, as these two PCI
devices are still attached to its parent's child device list as
maintained by the driver model. Some driver model PCI APIs like
dm_pci_find_class() used in the vesa_fb driver, are referring to
the list to speed up the finding process instead of re-enumerating
the whole PCI bus, so it gets the stale cached data which is wrong.
To fix this, manually remove these two devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Once we get udevice of IGD and SDVO, we can use its udevice to
access PCI configuration space with dm_pci_write_config32().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
So far disable_igd() does not have any return value, but we may need
that in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Now that we have irq router's udevice passed as a parameter, it's
time to start using the DM PCI API instead of those legacy ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present irq_router is declared as a static struct irq_router in
arch/x86/cpu/irq.c. Since it's a driver control block, it makes sense
to move it to a per driver priv. Adjust existing APIs to accept an
additional parameter of irq_router's udevice.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
There is no need to parse PCH's <reg> property as we have already
a DM PCI API dm_pci_get_bdf() that can handle this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
IOBASE is now obtained from PCH driver, drop this <io-base> property.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
asm/arch/gpio.h is not needed anymore as we get the GPIO base from
PCH driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present this GPIO driver still uses the legacy PCI API. Now that
we have proper PCH drivers we can use those to obtain the information
we need. While the device tree has nodes for the GPIO peripheral it is
not in the right place. It should be on the PCI bus as a sub-peripheral
of the PCH device.
Update the device tree files to show the GPIO controller within the PCH,
so that PCI access works as expected. This also adds '#address-cells'
and '#size-cells' to the PCH node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
On some newer chipset (eg: BayTrail), there is an IO base address
register on the PCH device which configures the base address of a
memory-mapped I/O controller.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
x86 GPIO registers are accessed via I/O port whose base address is
configured in a PCI configuration register on the PCH device. Add
an op get_gpio_base to get the GPIO base address from PCH.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
pch_get_version op was only used by the ich spi controller driver,
and does not really provide a good identification of pch controller
so far, since we see plenty of Intel PCH chipsets and one differs
from another a lot, which is not simply either a PCHV_7 or PCHV_9.
Now that ich spi controller driver was updated to not get such info
from pch, the pch_get_version op is useless now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The ICH SPI controller supports two variants, one of which is ICH7
compatible and the other is ICH9 compatible. Change 'pch_version'
to 'ich_version' to better match its original name.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
At present ich spi driver gets the controller version information via
pch, but this can be simply retrieved via spi node's compatible string.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
This cleans up the ich spi driver a little bit:
- Remove struct ich_spi_slave that is not referenced anywhere
- Remove ending period in some comments
- Move struct ich_spi_platdata and struct ich_spi_priv to ich.h
- Add #ifndef _ICH_H_ .. in ich.h
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Without this CONFIG_BOOTDELAY, autobooting does not work at all. As
autoboot_command() from common/* will not get called. So lets define
CONFIG_BOOTDELAY, so that auto-booting works on x86.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miao Yan <yanmiaobest@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Miao Yan <yanmiaobest@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
The x86 build target "efi-x86" has no TEXT_BASE configured. And with the
introduction of CONFIG_BOOTDELAY for x86, this function is now called
for this board as well. Resulting in compile errors for this target.
Without TEXT_BASE it makes no sense to fill these values. So lets only
configure the env variable if TEXT_BASE is defined.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Apparently, the logic for the FPGA global bit is not universal between Gen5
and Gen10 devices is not the same. Disabling this bit, while applicable to
Gen10 devices, will break FPGA programming on Gen5 devices.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
In current high speed fastboot, fs_ep_in.wMaxPacketSize is configured 64 bytes
as default, as a result, it failed to match the size at initialization stage in
usb controller.
Actually, hardware can support less than or equal to 512 bytes in high speed mode,
so I changed the condition from '!=' to '>' to fix this issue.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Tested-by: Steve Rae <srae@broadcom.com>
Implement board_mmc_get_env_dev for the boards.
Following is examples:
SD1/SD2/SD3: return devno;
SD2/SD3: return devno - 1;
SD2/SD4: if (devno == 2), return dev - 2; return dev - 1;
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC.
Introduce a weak function board_mmc_get_env_dev, different
boards can implement it according to different sdhc controllers
that used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
All boards using this driver are with device tree support,
hence drop the legacy code in driver to have a pure DT solution.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
All boards using this driver are with device tree support,
hence drop the legacy code in driver to have a pure DT solution.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Let's go with pure DT solution for board's
based on NXP/Freescale Vybrid platform.
- Merge the DT defconfig with non-DT defconfig for Toradex
Colibri VF50/VF61 and drop the non-DT defconfig.
- Update the legacy defconfigs for NXP/Freescale VF610 Tower
Board with DT.
- Update the legacy defconfigs for Phytec phyCORE-vybrid
Board with DT.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add device tree files for Phytec phyCORE-Vybrid Board.
- Enable lpuart support for Phytec phyCORE-Vybrid Board.
- Use UART1 for stdout.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add device tree files for NXP/Freescale VF610 Tower Board.
- Enable lpuart support on NXP/Freescale VF610 Tower Board.
- Use UART1 as stdout.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1
port, enable this display feature by adding relevant BSP codes
and configurations.
Signed-off-by: Ye Li <ye.li@nxp.com>
The checking with max frequency supported is not correct, because the temp
is calculated by max pre and post dividers. We can decrease any divider to
meet the max frequency limitation. Actually, the calculation below the codes
is doing this way to find best pre and post dividers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always
enter the -EINVAL return.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
As mx6slevk has only one Ethernet port, we don't need
to declare CONFIG_ETHPRIME, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.
So do as suggested by the LAN8720 datasheet.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.
So do as suggested in order to have Ethernet working again.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
Currently when building mxsboot on certain machines it reports:
HOSTCC tools/mxsboot
tools/mxsboot.c: In function 'mx28_create_sd_image':
tools/mxsboot.c:560: warning: implicit declaration of function 'htole32'
/tmp/cchLIV6q.o: In function 'main':
mxsboot.c:(.text+0x6d8): undefined reference to 'htole32'
mxsboot.c:(.text+0x6e7): undefined reference to 'htole32'
mxsboot.c:(.text+0x6f6): undefined reference to 'htole32'
mxsboot.c:(.text+0x705): undefined reference to 'htole32'
mxsboot.c:(.text+0x711): undefined reference to 'htole32'
/tmp/cchLIV6q.o:mxsboot.c:(.text+0x71d): more undefined references to
'htole32' follow
collect2: ld returned 1 exit status
make[1]: *** [tools/mxsboot] Error 1
make: *** [tools] Error 2
The solution is to use cpu_to_le32() instead which is more portable,
just like other U-Boot tools [1] do.
[1] http://lists.denx.de/pipermail/u-boot/2014-October/192919.html
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
All boards that support PXE booting use the pxefile_addr_r variable. Standardise
wandboard with this variable as pxe_addr_r isn't used anywhere else so it's a
typo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Enable the DDR calibration functionality on Novena to deal with the
memory SoDIMM on this board. Moreover, tweak the initial DDR DRAM
parameters so the calibration works properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code
fine-tunes the behavior of the MMDC controller in order to improve
the signal integrity and memory stability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-02 20:58:46 +01:00
1048 changed files with 24566 additions and 9480 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
